Jean Delvare [Mon, 15 Nov 2010 20:38:57 +0000 (21:38 +0100)]
hwmon: (w83795) Check for BEEP pin availability
On the W83795ADG, there's a single pin for BEEP and OVT#, so you
can't have both. Check the configuration and don't create beep
attributes when BEEP pin is not available.
The W83795G has a dedicated BEEP pin so the functionality is always
available there.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Jean Delvare [Mon, 15 Nov 2010 20:38:57 +0000 (21:38 +0100)]
hwmon: (w83795) Clear intrusion alarm immediately
When asked to clear the intrusion alarm, do so immediately. We have to
invalidate the cache to make sure the new status will be read. But we
also have to read from the status register once to clear the pending
alarm, as writing to CLR_CHS surprising won't clear it automatically.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Jean Delvare [Mon, 15 Nov 2010 20:38:56 +0000 (21:38 +0100)]
hwmon: (w83795) Read the intrusion state properly
We can't read the intrusion state from the real-time alarm registers
as we do for all other alarm flags, because real-time alarm bits don't
stick (by definition) and the intrusion state has to stick until
explicitly cleared (otherwise it has little value.)
So we have to use the interrupt status register instead, which is read
from the same address but with a configuration bit flipped in another
register.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Jean Delvare [Mon, 15 Nov 2010 20:38:56 +0000 (21:38 +0100)]
hwmon: (w83795) List all usable temperature sources
Temperature sources are not correlated directly with temperature
channels. A look-up table is required to find out which temperature
sources can be used depending on which temperature channels (both
analog and digital) are enabled.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Jean Delvare [Mon, 15 Nov 2010 20:38:56 +0000 (21:38 +0100)]
hwmon: (w83795) Expose fan control method
Expose fan control method (DC vs. PWM) using the standard sysfs
attributes. I've made it read-only as the board should be wired for
a given mode, the BIOS should have set up the chip for this mode, and
you shouldn't have to change it. But it would be easy enough to make
it changeable if someone comes up with a use case.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Jean Delvare [Mon, 15 Nov 2010 20:38:56 +0000 (21:38 +0100)]
hwmon: (w83795) Fix fan control mode attributes
There were two bugs:
* Speed cruise mode was improperly reported for all fans but fan1.
* Fan control method (PWM vs. DC) was mixed with the control mode.
It will be added back as a separate attribute, as per the standard
sysfs interface.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Jean Delvare [Mon, 15 Nov 2010 20:38:56 +0000 (21:38 +0100)]
hwmon: (lm95241) Check validity of input values
This clears the following build-time warnings I was seeing:
drivers/hwmon/lm95241.c: In function "set_interval":
drivers/hwmon/lm95241.c:132:15: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_max2":
drivers/hwmon/lm95241.c:278:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_max1":
drivers/hwmon/lm95241.c:277:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_min2":
drivers/hwmon/lm95241.c:249:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_min1":
drivers/hwmon/lm95241.c:248:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_type2":
drivers/hwmon/lm95241.c:220:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_type1":
drivers/hwmon/lm95241.c:219:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
This also fixes a small race in set_interval() as a side effect: by
working with a temporary local variable we prevent data->interval from
being accessed at a time it contains the interval value in the wrong
unit.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Davide Rizzo <elpa.rizzo@gmail.com>
Jim Bos [Sat, 13 Nov 2010 11:13:53 +0000 (12:13 +0100)]
i8k: Tell gcc that *regs gets clobbered
More recent GCC caused the i8k driver to stop working, on Slackware
compiler was upgraded from gcc-4.4.4 to gcc-4.5.1 after which it didn't
work anymore, meaning the driver didn't load or gave total nonsensical
output.
As it turned out the asm(..) statement forgot to mention it modifies the
*regs variable.
Credits to Andi Kleen and Andreas Schwab for providing the fix.
Signed-off-by: Jim Bos <jim876@xs4all.nl> Cc: Andi Kleen <andi@firstfloor.org> Cc: Andreas Schwab <schwab@linux-m68k.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Dave Jones <davej@redhat.com> Signed-off-by: Len Brown <len.brown@intel.com> Cc: stable@kernel.org (for 2.6.36) Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (66 commits)
can-bcm: fix minor heap overflow
gianfar: Do not call device_set_wakeup_enable() under a spinlock
ipv6: Warn users if maximum number of routes is reached.
docs: Add neigh/gc_thresh3 and route/max_size documentation.
axnet_cs: fix resume problem for some Ax88790 chip
ipv6: addrconf: don't remove address state on ifdown if the address is being kept
tcp: Don't change unlocked socket state in tcp_v4_err().
x25: Prevent crashing when parsing bad X.25 facilities
cxgb4vf: add call to Firmware to reset VF State.
cxgb4vf: Fail open if link_start() fails.
cxgb4vf: flesh out PCI Device ID Table ...
cxgb4vf: fix some errors in Gather List to skb conversion
cxgb4vf: fix bug in Generic Receive Offload
cxgb4vf: don't implement trivial (and incorrect) ndo_select_queue()
ixgbe: Look inside vlan when determining offload protocol.
bnx2x: Look inside vlan when determining checksum proto.
vlan: Add function to retrieve EtherType from vlan packets.
virtio-net: init link state correctly
ucc_geth: Fix deadlock
ucc_geth: Do not bring the whole IF down when TX failure.
...
Linus Torvalds [Sat, 13 Nov 2010 01:13:28 +0000 (17:13 -0800)]
Merge branch 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (28 commits)
Revert "USB: xhci: Use GFP_ATOMIC under spin_lock"
USB: ohci-jz4740: Fix spelling in MODULE_ALIAS
UWB: Return UWB_RSV_ALLOC_NOT_FOUND rather than crashing on NULL dereference if kzalloc fails
usb: core: fix information leak to userland
usb: misc: iowarrior: fix information leak to userland
usb: misc: sisusbvga: fix information leak to userland
usb: subtle increased memory usage in u_serial
USB: option: fix when the driver is loaded incorrectly for some Huawei devices.
USB: xhci: Use GFP_ATOMIC under spin_lock
usb: gadget: goku_udc: add registered flag bit, fixing build
USB: ehci/mxc: compile fix
USB: Fix FSL USB driver on non Open Firmware systems
USB: the development of the usb tree is now in git
usb: musb: fail unaligned DMA transfers on v1.8 and above
USB: ftdi_sio: add device IDs for Milkymist One JTAG/serial
usb.h: fix ioctl kernel-doc info
usb: musb: gadget: kill duplicate code in musb_gadget_queue()
usb: musb: Fix handling of spurious SESSREQ
usb: musb: fix kernel oops when loading musb_hdrc module for the 2nd time
USB: musb: blackfin: push clkin value to platform resources
...
Linus Torvalds [Sat, 13 Nov 2010 00:02:30 +0000 (16:02 -0800)]
Merge branch 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6
* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
n_gsm: Fix length handling
n_gsm: Copy n2 over when configuring via ioctl interface
serial: bfin_5xx: grab port lock before making port termios changes
serial: bfin_5xx: disable CON_PRINTBUFFER for consoles
serial: bfin_5xx: remove redundant SSYNC to improve TX speed
serial: bfin_5xx: always include DMA headers
vcs: make proper usage of the poll flags
amiserial: Remove unused variable icount
8250: Fix tcsetattr to avoid ioctl(TIOCMIWAIT) hang
tty_ldisc: Fix BUG() on hangup
TTY: restore tty_ldisc_wait_idle
SERIAL: blacklist si3052 chip
drivers/serial/bfin_5xx.c: Fix line continuation defects
tty: prevent DOS in the flush_to_ldisc
8250: add support for Kouwell KW-L221N-2
nozomi: Fix warning from the previous TIOCGCOUNT changes
tty: fix warning in synclink driver
tty: Fix formatting in tty.h
tty: the development tree is now done in git
Linus Torvalds [Sat, 13 Nov 2010 00:01:55 +0000 (16:01 -0800)]
Merge branch 'upstream/core' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen
* 'upstream/core' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen:
xen: do not release any memory under 1M in domain 0
xen: events: do not unmask event channels on resume
xen: correct size of level2_kernel_pgt
Linus Torvalds [Fri, 12 Nov 2010 23:54:39 +0000 (15:54 -0800)]
Merge branch 'stable/xen-pcifront-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
* 'stable/xen-pcifront-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
MAINTAINERS: Mark XEN lists as moderated
xen-pcifront: fix PCI reference leak
xen-pcifront: Remove duplicate inclusion of headers.
xen: fix memory leak in Xen PCI MSI/MSI-X allocator.
MAINTAINERS: Update mailing list name for Xen pieces.
Tejun Heo [Mon, 1 Nov 2010 10:39:19 +0000 (11:39 +0100)]
libata: fix NULL sdev dereference race in atapi_qc_complete()
SCSI commands may be issued between __scsi_add_device() and dev->sdev
assignment, so it's unsafe for ata_qc_complete() to dereference
dev->sdev->locked without checking whether it's NULL or not. Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org> Cc: stable@kernel.org Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Reported-by: Dan Rosenberg <drosenberg@vsecurity.com> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> CC: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
gianfar: Do not call device_set_wakeup_enable() under a spinlock
The gianfar driver calls device_set_wakeup_enable() under a spinlock,
which causes a problem to happen after the recent core power
management changes, because this function can sleep now. Fix this
by moving the device_set_wakeup_enable() call out of the
spinlock-protected area.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
Lorenzo Colitti [Wed, 27 Oct 2010 18:16:49 +0000 (18:16 +0000)]
ipv6: addrconf: don't remove address state on ifdown if the address is being kept
Currently, addrconf_ifdown does not delete statically configured IPv6
addresses when the interface is brought down. The intent is that when
the interface comes back up the address will be usable again. However,
this doesn't actually work, because the system stops listening on the
corresponding solicited-node multicast address, so the address cannot
respond to neighbor solicitations and thus receive traffic. Also, the
code notifies the rest of the system that the address is being deleted
(e.g, RTM_DELADDR), even though it is not. Fix it so that none of this
state is updated if the address is being kept on the interface.
Tested: Added a statically configured IPv6 address to an interface,
started ping, brought link down, brought link up again. When link came
up ping kept on going and "ip -6 maddr" showed that the host was still
subscribed to there
Signed-off-by: Lorenzo Colitti <lorenzo@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 12 Nov 2010 21:35:00 +0000 (13:35 -0800)]
tcp: Don't change unlocked socket state in tcp_v4_err().
Alexey Kuznetsov noticed a regression introduced by
commit f1ecd5d9e7366609d640ff4040304ea197fbc618
("Revert Backoff [v3]: Revert RTO on ICMP destination unreachable")
The RTO and timer modification code added to tcp_v4_err()
doesn't check sock_owned_by_user(), which if true means we
don't have exclusive access to the socket and therefore cannot
modify it's critical state.
Just skip this new code block if sock_owned_by_user() is true
and eliminate the now superfluous sock_owned_by_user() code
block contained within.
Reported-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru> Signed-off-by: David S. Miller <davem@davemloft.net> CC: Damian Lukowski <damian@tvk.rwth-aachen.de> Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Dan Rosenberg [Fri, 12 Nov 2010 20:44:42 +0000 (12:44 -0800)]
x25: Prevent crashing when parsing bad X.25 facilities
Now with improved comma support.
On parsing malformed X.25 facilities, decrementing the remaining length
may cause it to underflow. Since the length is an unsigned integer,
this will result in the loop continuing until the kernel crashes.
This patch adds checks to ensure decrementing the remaining length does
not cause it to wrap around.
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Casey Leedom [Thu, 11 Nov 2010 09:06:50 +0000 (09:06 +0000)]
cxgb4vf: fix some errors in Gather List to skb conversion
There were some errors in the way that internal Gather Lists were being
translated into skb's. This also makes the VF Driver look more like the PF
Driver to facilitate easier comarison.
Signed-off-by: Casey Leedom <leedom@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Don't implement (struct net_device_ops *)->ndo_select_queue() with simple
call to skb_tx_hash(). This leads to non-persistent TX queue selection in
the Linux dev_pick_tx() routine for TCP connections.
Signed-off-by: Casey Leedom <leedom@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hao Zheng [Thu, 11 Nov 2010 13:47:59 +0000 (13:47 +0000)]
ixgbe: Look inside vlan when determining offload protocol.
Currently the skb->protocol field is used to setup various
offloading parameters on transmit for the correct protocol.
However, if vlan offloading is disabled or otherwise not used,
the protocol field will be ETH_P_8021Q, not the actual protocol.
This will cause the offloading to be not performed correctly,
even though the hardware is capable of looking inside vlan tags.
Instead, look inside the header if necessary to determine the
correct protocol type.
To some extent this fixes a regression from 2.6.36 because it
was previously not possible to disable vlan offloading and this
error case was not exposed.
Signed-off-by: Hao Zheng <hzheng@nicira.com> CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com> CC: Alex Duyck <alexander.h.duyck@intel.com> CC: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jesse Gross <jesse@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hao Zheng [Thu, 11 Nov 2010 13:47:58 +0000 (13:47 +0000)]
bnx2x: Look inside vlan when determining checksum proto.
Currently the skb->protocol field is used to setup checksum
offloading on transmit for the correct protocol. However, if
vlan offloading is disabled or otherwise not used, the protocol
field will be ETH_P_8021Q, not the actual protocol. This will
cause the checksum to be not computed correctly, even though the
hardware is capable of looking inside vlan tags. Instead,
look inside the header if necessary to determine the correct
protocol type.
To some extent this fixes a regression from 2.6.36 because it
was previously not possible to disable vlan offloading and this
error case was not exposed.
Signed-off-by: Hao Zheng <hzheng@nicira.com> CC: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: Jesse Gross <jesse@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hao Zheng [Thu, 11 Nov 2010 13:47:57 +0000 (13:47 +0000)]
vlan: Add function to retrieve EtherType from vlan packets.
Depending on how a packet is vlan tagged (i.e. hardware accelerated or
not), the encapsulated protocol is stored in different locations. This
provides a consistent method of accessing that protocol, which is needed
by drivers, security checks, etc.
Signed-off-by: Hao Zheng <hzheng@nicira.com> Signed-off-by: Jesse Gross <jesse@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Wed, 10 Nov 2010 14:45:41 +0000 (14:45 +0000)]
virtio-net: init link state correctly
For device that supports VIRTIO_NET_F_STATUS, there's no need to
assume the link is up and we need to call nerif_carrier_off() before
querying device status, otherwise we may get wrong operstate after
diver was loaded because the link watch event was not fired as
expected.
For device that does not support VIRITO_NET_F_STATUS, we could not get
its status through virtnet_update_status() and what we can only do is
always assuming the link is up.
Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Jason Wang <jasowang@redhat.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
The reason appears to be ucc_geth_stop meets adjust_link as the
PHY reports PHY changes. I belive adjust_link hangs somewhere,
holding the PHY lock, because ucc_geth_stop disabled the
controller HW.
Fix is to stop the PHY before disabling the controller.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se> Reviewed-by: Anton Vorontsov <cbouatmailru@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Joakim Tjernlund [Fri, 12 Nov 2010 03:55:08 +0000 (03:55 +0000)]
ucc_geth: Do not bring the whole IF down when TX failure.
ucc_geth_close lacks a cancel_work_sync(&ugeth->timeout_work)
to stop any outstanding processing of TX fail. However, one
can not call cancel_work_sync without fixing the timeout function
otherwise it will deadlock. This patch brings ucc_geth in line with
gianfar:
Don't bring the interface down and up, just reinit controller HW
and PHY.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se> Reviewed-by: Anton Vorontsov <cbouatmailru@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Graf [Thu, 11 Nov 2010 15:47:59 +0000 (15:47 +0000)]
rtnetlink: Fix message size calculation for link messages
nlmsg_total_size() calculates the length of a netlink message
including header and alignment. nla_total_size() calculates the
space an individual attribute consumes which was meant to be used
in this context.
Also, ensure to account for the attribute header for the
IFLA_INFO_XSTATS attribute as implementations of get_xstats_size()
seem to assume that we do so.
The addition of two message headers minus the missing attribute
header resulted in a calculated message size that was larger than
required. Therefore we never risked running out of skb tailroom.
Signed-off-by: Thomas Graf <tgraf@infradead.org> Acked-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 12 Nov 2010 18:30:49 +0000 (10:30 -0800)]
Merge master.kernel.org:/home/rmk/linux-2.6-arm
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: GIC: don't disable software generated interrupts
ARM: 6472/1: vexpress ct-ca9x4: only set twd_base if local timers are being used
ARM: arch/arm/kernel/traps.c: Convert sprintf_symbol to %pS
ARM: arch/arm/kernel/hw_breakpoint.c: Convert WARN_ON to WARN
ARM: 6462/1: EP93xx: Document DMA M2P API
ARM: 6470/1: atomic64: use generic implementation for OABI configurations
ARM: 6469/1: perf-events: squash compiler warning
ARM: 6468/1: backtrace: fix calculation of thread stack base
ARM: Fix DMA coherent allocator alignment
ARM: orion5x/kirkwood/mv78xx0: fix MPP configuration corner cases
[ARM] TS-78xxx NAND resource type should be IORESOURCE_MEM
ARM: pxa/saar: fix the building failure caused by typo
ARM: pxa/cm-x2xx: remove duplicate call to pxa27x_init_irq
ARM: pxa: fix the missing definition of IRQ_BOARD_END
ARM: mmp: fix cpuid detection on mmp2
[ARM] Kirkwood: restrict the scope of the PCIe reset workaround
[ARM] Kirkwood: fix timer initialization for LaCie boards
[ARM] Kirkwood: enhance TCLK detection
Linus Torvalds [Fri, 12 Nov 2010 17:52:31 +0000 (09:52 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: do not pass injected events back to the originating handler
Input: pcf8574_keypad - fix error handling in pcf8574_kp_probe
Input: acecad - fix a memory leak in usb_acecad_probe error path
Input: atkbd - add 'terminal' parameter for IBM Terminal keyboards
Input: i8042 - add Sony VAIOs to MUX blacklist
kgdboc: reset input devices (keyboards) when exiting debugger
Input: export input_reset_device() for use in KGDB
Input: adp5588-keys - unify common header defines
Linus Torvalds [Fri, 12 Nov 2010 16:52:47 +0000 (08:52 -0800)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/linux-2.6-block: (27 commits)
block: remove unused copy_io_context()
Documentation: remove anticipatory scheduler info
block: remove REQ_HARDBARRIER
ioprio: rcu_read_lock/unlock protect find_task_by_vpid call (V2)
ioprio: fix RCU locking around task dereference
block: ioctl: fix information leak to userland
block: read i_size with i_size_read()
cciss: fix proc warning on attempt to remove non-existant directory
bio: take care not overflow page count when mapping/copying user data
block: limit vec count in bio_kmalloc() and bio_alloc_map_data()
block: take care not to overflow when calculating total iov length
block: check for proper length of iov entries in blk_rq_map_user_iov()
cciss: remove controllers supported by hpsa
cciss: use usleep_range not msleep for small sleeps
cciss: limit commands allocated on reset_devices
cciss: Use kernel provided PCI state save and restore functions
cciss: fix board status waiting code
drbd: Removed checks for REQ_HARDBARRIER on incomming BIOs
drbd: REQ_HARDBARRIER -> REQ_FUA transition for meta data accesses
drbd: Removed the BIO_RW_BARRIER support form the receiver/epoch code
...
Linus Torvalds [Fri, 12 Nov 2010 16:39:52 +0000 (08:39 -0800)]
Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf, amd: Use kmalloc_node(,__GFP_ZERO) for northbridge structure allocation
perf_events: Fix time tracking in samples
perf trace: update usage
perf trace: update Documentation with new perf trace variants
perf trace: live-mode command-line cleanup
perf trace record: handle commands correctly
perf record: make the record options available outside perf record
perf trace scripting: remove system-wide param from shell scripts
perf trace scripting: fix some small memory leaks and missing error checks
perf: Fix usages of profile_cpu in builtin-top.c to use cpu_list
perf, ui: Eliminate stack-smashing protection compiler complaint
Linus Torvalds [Fri, 12 Nov 2010 16:11:58 +0000 (08:11 -0800)]
Merge branch 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (39 commits)
drm/ttm: Be consistent on ttm_bo_init() failures
drm/radeon/kms: Fix retrying ttm_bo_init() after it failed once.
drm/radeon/kms: fix thermal sensor reporting on rv6xx
drm/radeon/kms: fix bugs in ddc and cd path router code
drm/radeon/kms: add support for clock/data path routers
drm: vmwgfx: fix information leak to userland
drivers/gpu: Use vzalloc
drm/vmwgfx: Fix oops on failing bo pin
drm/ttm: Remove the CAP_SYS_ADMIN requirement for bo pinning
drm/ttm: Make sure a sync object doesn't disappear while we use it
drm/radeon/kms: don't disable shared encoders on pre-DCE3 display blocks
drivers/gpu/drm: Update WARN uses
drivers/gpu/drm/vmwgfx: Fix k.alloc switched arguments
DRM: ignore invalid EDID extensions
drm/radeon/kms: make the connector code less verbose
drm/ttm: remove failed ttm binding error printout
drm/ttm: Add a barrier when unreserving
drm/ttm: Remove mm init error printouts and checks
drm/ttm: Remove pointless list_empty check
drm/ttm: Use private locks for the default bo range manager
...
Linus Torvalds [Fri, 12 Nov 2010 16:11:03 +0000 (08:11 -0800)]
Merge branch 'for-linus' of git://oss.sgi.com/xfs/xfs
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: remove incorrect assert in xfs_vm_writepage
xfs: use hlist_add_fake
xfs: fix a few compiler warnings with CONFIG_XFS_QUOTA=n
xfs: tell lockdep about parent iolock usage in filestreams
xfs: move delayed write buffer trace
xfs: fix per-ag reference counting in inode reclaim tree walking
xfs: xfs_ioctl: fix information leak to userland
xfs: remove experimental tag from the delaylog option
Steffen Klassert [Wed, 10 Nov 2010 11:21:43 +0000 (12:21 +0100)]
crypto: pcrypt - Fix use after free on padata_free
kobject_put is called from padata_free for the padata kobject.
The kobject's release function frees the padata instance,
so don't call kobject_put for the padata kobject from pcrypt.
drivers/video/backlight/adp8860_bl.c: check strict_strtoul() return value
Handle return value, strict_strtoul is declared with attribute
warn_unused_result.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Cc: Mike Frysinger <vapier@gentoo.org> Acked-by: Richard Purdie <rpurdie@linux.intel.com> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/video/backlight/adp8860_bl.c: fix ambient light zone overwrite handling
This affects the get/set of the current Ambient Light Zone. Reading
should return an integer between 1..3 (1 = Daylight, 2 = office, 3 =
dark). Writing a value between 1..3 forces the backlight controller to
enter the corresponding Ambient Light Zone. Writing 0 returns to normal
operation.
Fix valid range checking so we don't write invalid values to the
controller, and make sure we subtract 1, since this is what the register
definition (CFGR:BLV) requires. Otherwise the values written don't work
correctly.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Richard Purdie <rpurdie@linux.intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arun Murthy [Thu, 11 Nov 2010 22:05:28 +0000 (14:05 -0800)]
backlight: add low threshold to pwm backlight
The intensity of the backlight can be varied from a range of
max_brightness to zero. Though most, if not all the pwm based backlight
devices start flickering at lower brightness value. And also for each
device there exists a brightness value below which the backlight appears
to be turned off though the value is not equal to zero.
If the range of brightness for a device is from zero to max_brightness. A
graph is plotted for brightness Vs intensity for the pwm based backlight
device has to be a linear graph.
But pratically on measuring the above we note that the intensity of
backlight goes to zero(OFF) when the value in not zero almost nearing to
zero(some x%). so the graph looks like
In order to overcome this drawback knowing this x% i.e nothing but the low
threshold beyond which the backlight is off and will have no effect, the
brightness value is being offset by the low threshold value(retaining the
linearity of the graph). Now the graph becomes
With this for each and every digit increment in the brightness from zero
there is a change in the intensity of backlight. Devices having this
behaviour can set the low threshold brightness(lth_brightness) and pass
the same as platform data else can have it as zero.
Eliminate section mismatch warning by marking s6e63m0_probe() as __devinit.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Richard Purdie <rpurdie@linux.intel.com> Cc: InKi Dae <inki.dae@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Axel Lin [Thu, 11 Nov 2010 22:05:26 +0000 (14:05 -0800)]
drivers/video/backlight/s6e63m0.c: unregister backlight device and remove sysfs attribute file in s6e63m0_remove
s6e63m0_probe() registered backlight device and create sysfs attribute
files, thus s6e63m0_remove() should unregister backlight device and remove
sysfs attribute files.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Richard Purdie <rpurdie@linux.intel.com> Cc: InKi Dae <inki.dae@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Axel Lin [Thu, 11 Nov 2010 22:05:25 +0000 (14:05 -0800)]
drivers/video/backlight/s6e63m0.c: set permissions on gamma_table file to 0444
gamma_table is not writable, so set permissions to 0444.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Richard Purdie <rpurdie@linux.intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Davidlohr Bueso [Thu, 11 Nov 2010 22:05:24 +0000 (14:05 -0800)]
drivers/leds/leds-gpio.c: properly initialize return value
In the event that none of the configs are set (CONFIG_LEDS_GPIO_PLATFORM,
CONFIG_LEDS_GPIO_OF, CONFIG_LEDS_GPIO_PLATFORM), we will return a bogus
value when initializing the module.
Signed-off-by: Davidlohr Bueso <dave@gnu.org> Acked-by: Richard Purdie <rpurdie@linux.intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Samu Onkalo [Thu, 11 Nov 2010 22:05:22 +0000 (14:05 -0800)]
leds: driver for National Semiconductors LP5523 chip
LP5523 chip is nine channel led driver with programmable engines. Driver
provides support for that chip for direct access via led class or via
programmable engines.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Cc: Richard Purdie <rpurdie@rpsys.net> Cc: Jean Delvare <khali@linux-fr.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Samu Onkalo [Thu, 11 Nov 2010 22:05:22 +0000 (14:05 -0800)]
leds: driver for National Semiconductor LP5521 chip
This patchset provides support for LP5521 and LP5523 LED driver chips from
National Semicondutor. Both drivers supports programmable engines and
naturally LED class features.
Documentation is provided as a part of the patchset. I created "leds"
subdirectory under Documentation. Perhaps the rest of the leds*
documentation should be moved there.
Datasheets are freely available at National Semiconductor www pages.
This patch:
LP5521 chip is three channel led driver with programmable engines. Driver
provides support for that chip for direct access via led class or via
programmable engines.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Cc: Richard Purdie <rpurdie@rpsys.net> Cc: Jean Delvare <khali@linux-fr.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Berg [Thu, 11 Nov 2010 22:05:21 +0000 (14:05 -0800)]
led-class: always implement blinking
Currently, blinking LEDs can be awkward because it is not guaranteed that
all LEDs implement blinking. The trigger that wants it to blink then
needs to implement its own timer solution.
Rather than require that, add led_blink_set() API that triggers can use.
This function will attempt to use hw blinking, but if that fails
implements a timer for it. To stop blinking again, brightness_set() also
needs to be wrapped into API that will stop the software blink.
As a result of this, the timer trigger becomes a very trivial one, and
hopefully we can finally see triggers using blinking as well because it's
always easy to use.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Acked-by: Richard Purdie <rpurdie@linux.intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Jones [Thu, 11 Nov 2010 22:05:20 +0000 (14:05 -0800)]
hugetlbfs: lessen the impact of a deprecation warning
WARN_ONCE is a bit strong for a deprecation warning, given that it spews a
huge backtrace.
Signed-off-by: Dave Jones <davej@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nick Piggin [Thu, 11 Nov 2010 22:05:19 +0000 (14:05 -0800)]
radix-tree: fix RCU bug
Salman Qazi describes the following radix-tree bug:
In the following case, we get can get a deadlock:
0. The radix tree contains two items, one has the index 0.
1. The reader (in this case find_get_pages) takes the rcu_read_lock.
2. The reader acquires slot(s) for item(s) including the index 0 item.
3. The non-zero index item is deleted, and as a consequence the other item is
moved to the root of the tree. The place where it used to be is queued for
deletion after the readers finish.
3b. The zero item is deleted, removing it from the direct slot, it remains in
the rcu-delayed indirect node.
4. The reader looks at the index 0 slot, and finds that the page has 0 ref
count
5. The reader looks at it again, hoping that the item will either be freed or
the ref count will increase. This never happens, as the slot it is looking
at will never be updated. Also, this slot can never be reclaimed because
the reader is holding rcu_read_lock and is in an infinite loop.
The fix is to re-use the same "indirect" pointer case that requires a slot
lookup retry into a general "retry the lookup" bit.
Signed-off-by: Nick Piggin <npiggin@kernel.dk> Reported-by: Salman Qazi <sqazi@google.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dan Rosenberg [Thu, 11 Nov 2010 22:05:18 +0000 (14:05 -0800)]
Restrict unprivileged access to kernel syslog
The kernel syslog contains debugging information that is often useful
during exploitation of other vulnerabilities, such as kernel heap
addresses. Rather than futilely attempt to sanitize hundreds (or
thousands) of printk statements and simultaneously cripple useful
debugging functionality, it is far simpler to create an option that
prevents unprivileged users from reading the syslog.
This patch, loosely based on grsecurity's GRKERNSEC_DMESG, creates the
dmesg_restrict sysctl. When set to "0", the default, no restrictions are
enforced. When set to "1", only users with CAP_SYS_ADMIN can read the
kernel syslog via dmesg(8) or other mechanisms.
[akpm@linux-foundation.org: explain the config option in kernel.txt] Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com> Acked-by: Ingo Molnar <mingo@elte.hu> Acked-by: Eugene Teo <eugeneteo@kernel.org> Acked-by: Kees Cook <kees.cook@canonical.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Rientjes [Thu, 11 Nov 2010 22:05:18 +0000 (14:05 -0800)]
oom: document obsolete oom_adj tunable
/proc/pid/oom_adj was deprecated in August 2010 with the introduction of
the new oom killer heuristic.
This patch copies the Documentation/feature-removal-schedule.txt entry for
this tunable to the Documentation/ABI/obsolete directory so nobody misses
it.
Signed-off-by: David Rientjes <rientjes@google.com> Reported-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Shaohua Li [Thu, 11 Nov 2010 22:05:17 +0000 (14:05 -0800)]
vmscan: avoid setting zone congested if no page dirty
nr_dirty and nr_congested are increased only when the page is dirty. So
if all pages are clean, both them will be zero. In this case, we should
not mark the zone congested.
Signed-off-by: Shaohua Li <shaohua.li@intel.com> Reviewed-by: Johannes Weiner <hannes@cmpxchg.org> Reviewed-by: Minchan Kim <minchan.kim@gmail.com> Acked-by: Mel Gorman <mel@csn.ul.ie> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ken Chen [Thu, 11 Nov 2010 22:05:16 +0000 (14:05 -0800)]
latencytop: fix per task accumulator
Per task latencytop accumulator prematurely terminates due to erroneous
placement of latency_record_count. It should be incremented whenever a
new record is allocated instead of increment on every latencytop event.
Also fix search iterator to only search known record events instead of
blindly searching all pre-allocated space.
Signed-off-by: Ken Chen <kenchen@google.com> Reviewed-by: Arjan van de Ven <arjan@infradead.org> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Hansen [Thu, 11 Nov 2010 22:05:15 +0000 (14:05 -0800)]
mm/vfs: revalidate page->mapping in do_generic_file_read()
70 hours into some stress tests of a 2.6.32-based enterprise kernel, we
ran into a NULL dereference in here:
int block_is_partially_uptodate(struct page *page, read_descriptor_t *desc,
unsigned long from)
{
----> struct inode *inode = page->mapping->host;
It looks like page->mapping was the culprit. (xmon trace is below).
After closer examination, I realized that do_generic_file_read() does a
find_get_page(), and eventually locks the page before calling
block_is_partially_uptodate(). However, it doesn't revalidate the
page->mapping after the page is locked. So, there's a small window
between the find_get_page() and ->is_partially_uptodate() where the page
could get truncated and page->mapping cleared.
We _have_ a reference, so it can't get reclaimed, but it certainly
can be truncated.
I think the correct thing is to check page->mapping after the
trylock_page(), and jump out if it got truncated. This patch has been
running in the test environment for a month or so now, and we have not
seen this bug pop up again.
kernel/range.c: fix clean_sort_range() for the case of full array
clean_sort_range() should return a number of nonempty elements of range
array, but if the array is full clean_sort_range() returns 0.
The problem is that the number of nonempty elements is evaluated by
finding the first empty element of the array. If there is no such element
it returns an initial value of local variable nr_range that is zero.
The fix is trivial: it changes initial value of nr_range to size of the
array.
The bug can lead to loss of information regarding all ranges, since
typically returned value of clean_sort_range() is considered as an actual
number of ranges in the array after a series of add/subtract operations.
Found by Analytical Verification project of Linux Verification Center
(linuxtesting.org), thanks to Alexander Kolosov.
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru> Cc: Yinghai Lu <yinghai@kernel.org> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dan Carpenter [Thu, 11 Nov 2010 22:05:13 +0000 (14:05 -0800)]
drivers/misc/bh1770glc.c: error handling in bh1770_power_state_store()
There was a signedness bug so "ret" was never less than zero and that
breaks the error handling. Also in the original code it would overwrite
ret and the result is still negative but it's bogus number instead of the
correct error code.
Signed-off-by: Dan Carpenter <error27@gmail.com> Cc: Samu Onkalo <samu.p.onkalo@nokia.com> Cc: Jonathan Cameron <jic23@cam.ac.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dan Carpenter [Thu, 11 Nov 2010 22:05:12 +0000 (14:05 -0800)]
memcg: null dereference on allocation failure
The original code had a null dereference if alloc_percpu() failed. This
was introduced in commit 711d3d2c9bc3 ("memcg: cpu hotplug aware percpu
count updates")
Catalin Marinas [Thu, 11 Nov 2010 22:05:10 +0000 (14:05 -0800)]
include/linux/highmem.h needs hardirq.h
Commit 3e4d3af501cc ("mm: stack based kmap_atomic()") introduced the
kmap_atomic_idx_push() function which warns on in_irq() with
CONFIG_DEBUG_HIGHMEM enabled. This patch includes linux/hardirq.h for
the in_irq definition.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eric Dumazet [Thu, 11 Nov 2010 22:05:08 +0000 (14:05 -0800)]
atomic: add atomic_inc_not_zero_hint()
Followup of perf tools session in Netfilter WorkShop 2010
In the network stack we make high usage of atomic_inc_not_zero() in
contexts we know the probable value of atomic before increment (2 for udp
sockets for example)
Using a special version of atomic_inc_not_zero() giving this hint can help
processor to use less bus transactions.
On x86 (MESI protocol) for example, this avoids entering Shared state,
because "lock cmpxchg" issues an RFO (Read For Ownership)
akpm: Adds a new include/linux/atomic.h. This means that new code should
henceforth include linux/atomic.h and not asm/atomic.h. The presence of
include/linux/atomic.h will in fact cause checkpatch.pl to warn about use
of asm/atomic.h. The new include/linux/atomic.h becomes the place where
arch-neutral atomic_t code should be placed.
[akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Cc: Christoph Lameter <cl@linux-foundation.org> Cc: Ingo Molnar <mingo@elte.hu> Cc: Andi Kleen <andi@firstfloor.org> Cc: Arnaldo Carvalho de Melo <acme@infradead.org> Cc: David Miller <davem@davemloft.net> Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com> Cc: Nick Piggin <npiggin@kernel.dk> Reviewed-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dan Carpenter [Thu, 11 Nov 2010 22:05:07 +0000 (14:05 -0800)]
rapidio: use resource_size()
The size calculation is done incorrectly here because it should include
both the start and end (end - start + 1). It's easiest to just use
resource_size() which does the right thing.
I was worried there was something non-standard going on because the
printk() subtracts "end - 1", but the rest of the file uses the normal
resource size calculations. This function is only called from
fsl_rio_setup() in arch/powerpc/sysdev/fsl_rio.c and the calculation
there is also:
Signed-off-by: Dan Carpenter <error27@gmail.com> Cc: Alexandre Bounine <alexandre.bounine@idt.com> Acked-by: Li Yang <leoli@freescale.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/macintosh/adb-iop.c: flags should be unsigned long
Fix these warnings:
drivers/macintosh/adb-iop.c: In function `adb_iop_complete':
drivers/macintosh/adb-iop.c:85: warning: comparison of distinct pointer types lacks a cast
drivers/macintosh/adb-iop.c:92: warning: comparison of distinct pointer types lacks a cast
drivers/macintosh/adb-iop.c: In function ¡adb_iop_listen¢:
drivers/macintosh/adb-iop.c:111: warning: comparison of distinct pointer types lacks a cast
drivers/macintosh/adb-iop.c:151: warning: comparison of distinct pointer types lacks a cast
Both commits 0a3d763f1a68 ("ptrace: cleanup arch_ptrace() on um") and 9b05a69e0534 ("ptrace: change signature of arch_ptrace()") broke the um
build. This patch fixes the issues.
0a3d763f1a68 introduced the undeclared variable "datavp". The patch seems
completely untested. :-(
9b05a69e0534 changed arch_ptrace()'s signature but did not update
um/include/asm/ptrace-generic.h.
Signed-off-by: Richard Weinberger <richard@nod.at> Cc: Namhyung Kim <namhyung@gmail.com> Cc: Jeff Dike <jdike@addtoit.com> Tested-by: Will Newton <will.newton@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Software generated interrupts (SGI) are used for IPIs by the kernel.
While previous revisions of the GIC hardware were specified not to
implement enable bits for SGIs, more recent hardware is now permitted
to implement these bits in a per-CPU banked register.
The priority registers for the PPI and SGIs are also per-CPU banked
registers, so ensure that these are also appropriately initialized.
Reported-by: Scott Valentine <svalentine@concentris-systems.com> Acked-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Eric Paris [Fri, 12 Nov 2010 07:26:06 +0000 (08:26 +0100)]
netfilter: NF_HOOK_COND has wrong conditional
The NF_HOOK_COND returns 0 when it shouldn't due to what I believe to be an
error in the code as the order of operations is not what was intended. C will
evalutate == before =. Which means ret is getting set to the bool result,
rather than the return value of the function call. The code says
if (ret = function() == 1)
when it meant to say:
if ((ret = function()) == 1)
Normally the compiler would warn, but it doesn't notice it because its
a actually complex conditional and so the wrong code is wrapped in an explict
set of () [exactly what the compiler wants you to do if this was intentional].
Fixing this means that errors when netfilter denies a packet get propagated
back up the stack rather than lost.
Problem introduced by commit 2249065f (netfilter: get rid of the grossness
in netfilter.h).
Signed-off-by: Eric Paris <eparis@redhat.com> Cc: stable@kernel.org Signed-off-by: Patrick McHardy <kaber@trash.net>
Sonic Zhang [Wed, 27 Oct 2010 08:16:48 +0000 (04:16 -0400)]
serial: bfin_5xx: remove redundant SSYNC to improve TX speed
We don't need to force a SSYNC here as the LSR register will already
be updated by the time we get back to reading it. This speeds up TX
throughput and lowers general system overhead (since SSYNC is system
wide, not peripheral-specific).
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
projects / mirror_ubuntu-disco-kernel.git / log