rt2800: replace msleep() with usleep_range() on channel switch
msleep(1) can sleep much more time then requested 1ms, this is not good
on channel switch, which we want to be performed fast (i.e. to make scan
faster). Replace msleep() with usleep_range(), which has much smaller
maximum sleeping time boundary.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We need to perform different actions (AGC and VCO calibrations and VGC
tuning) periodically at different intervals. We don't need separate
works for those, we can use link tuner work and just check for proper
interval on it.
This fixes performing AGC and VCO calibration when scanning on STA
mode. We need to be on-channel to perform those calibrations.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rt2800: set MAX_PSDU len according to remote STAs capabilities
MAX_LEN_CFG_MAX_PSDU specify maximum transmitted by HW AMPDU length
(0 - 8kB, 1 - 16kB, 2 - 32kB, 3 - 64kB). Set this option according to
remote stations capabilities (based on HT ampdu_factor). However limit
the value based our hardware TX capabilities as some chips can not send
more than 16kB (factor 1). Limit for all chips is currently 32kB
(factor 2), but perhaps for some chips this could be increased
to 64kB by setting drv_data->max_psdu to 3.
Since MAX_LEN_CFG_MAX_PSDU is global setting, on multi stations modes
(AP, IBSS, mesh) we limit according to less capable remote STA. We can
not set bigger value to speed up communication with some stations and
do not break communication with slow stations.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
orinoco: Use shash instead of ahash for MIC calculations
Eric Biggers pointed out that the orinoco driver pointed scatterlists
at the stack.
Fix it by switching from ahash to shash. The result should be
simpler, faster, and more correct.
Cc: stable@vger.kernel.org # 4.9 only Reported-by: Eric Biggers <ebiggers3@gmail.com> Signed-off-by: Andy Lutomirski <luto@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Johannes Berg [Wed, 7 Dec 2016 06:36:46 +0000 (07:36 +0100)]
iwlegacy: make il3945_mac_ops __ro_after_init
There's no need for this to be only __read_mostly, since
it's only written in a single way depending on the module
parameter, so that can be moved into the module's __init
function, and the ops can be __ro_after_init.
This is a little bit safer since it means the ops can't
be overwritten (accidentally or otherwise), which would
otherwise cause an arbitrary function or bad pointer to
be called.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Acked-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mwifiex: sdio: fix use after free issue for save_adapter
If we have sdio work requests received when sdio card reset is
happening, we may end up accessing older save_adapter pointer
later which is already freed during card reset.
This patch solves the problem by cancelling those pending requests.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Erik Nordmark [Fri, 2 Dec 2016 22:00:08 +0000 (14:00 -0800)]
ipv6 addrconf: Implemented enhanced DAD (RFC7527)
Implemented RFC7527 Enhanced DAD.
IPv6 duplicate address detection can fail if there is some temporary
loopback of Ethernet frames. RFC7527 solves this by including a random
nonce in the NS messages used for DAD, and if an NS is received with the
same nonce it is assumed to be a looped back DAD probe and is ignored.
RFC7527 is enabled by default. Can be disabled by setting both of
conf/{all,interface}/enhanced_dad to zero.
Signed-off-by: Erik Nordmark <nordmark@arista.com> Signed-off-by: Bob Gilligan <gilligan@arista.com> Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 4 Dec 2016 04:18:39 +0000 (23:18 -0500)]
Merge branch 'mv88e6390-batch-three'
Andrew Lunn says:
====================
mv88e6390 batch 3
More patches to support the MV88e6390. This is mostly refactoring
existing code and adding implementations for the mv88e6390. This
patchset set which reserved frames are sent to the cpu, the size of
jumbo frames that will be accepted, turn off egress rate limiting, and
configuration of pause frames.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sat, 3 Dec 2016 03:45:19 +0000 (04:45 +0100)]
net: dsa: mv88e6xxx: Refactor pause configuration
The mv88e6390 has a different mechanism for configuring pause.
Refactor the code into an ops function, and for the moment, don't add
any mv88e6390 code yet.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sat, 3 Dec 2016 03:45:16 +0000 (04:45 +0100)]
net: dsa: mv88e6xxx: Reserved Management frames to CPU
Older devices have a couple of registers in global2. The mv88e6390
family has a single register in global1 behind which hides similar
configuration. Implement and op for this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 4 Dec 2016 04:15:01 +0000 (23:15 -0500)]
Merge branch 'mv88e6390-batch-two'
Andrew Lunn says:
====================
MV88E6390 batch two
This is the second batch of patches adding support for the
MV88e6390. They are not sufficient to make it work properly.
The mv88e6390 has a much expanded set of priority maps. Refactor the
existing code, and implement basic support for the new device.
Similarly, the monitor control register has been reworked.
The mv88e6390 has something odd in its EDSA tagging implementation,
which means it is not possible to use it. So we need to use DSA
tagging. This is the first device with EDSA support where we need to
use DSA, and the code does not support this. So two patches refactor
the existing code. The two different register definitions are
separated out, and using DSA on an EDSA capable device is added.
v2:
Add port prefix
Add helper function for 6390
Add _IEEE_ into #defines
Split monitor_ctrl into a number of separate ops.
Remove 6390 code which is management, used in a later patch
s/EGREES/EGRESS/.
Broke up setup_port_dsa() and set_port_dsa() into a number of ops
v3:
Verify mandatory ops for port setup
Don't set ether type for DSA port.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sat, 3 Dec 2016 03:35:19 +0000 (04:35 +0100)]
net: dsa: mv88e6xxx: Refactor CPU and DSA port setup
Older chips only support DSA tagging. Newer chips have both DSA and
EDSA tagging. Refactor the code by adding port functions for setting the
frame mode, egress mode, and if to forward unknown frames.
This results in the helper mv88e6xxx_6065_family() becoming unused, so
remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v3:
Verify mandatory ops for port setup
Don't set ether type for DSA port. Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sat, 3 Dec 2016 03:35:18 +0000 (04:35 +0100)]
net: dsa: mv88e6xxx: Move the tagging protocol into info
Older chips support a single tagging protocol, DSA. New chips support
both DSA and EDSA, an enhanced version. Having both as an option
changes the register layouts. Up until now, it has been assumed that
if EDSA is supported, it will be used. Hence the register layout has
been determined by which protocol should be used. However, mv88e6390
has a different implementation of EDSA, which requires we need to use
the DSA tagging. Hence separate the selection of the protocol from the
register layout.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sat, 3 Dec 2016 03:35:16 +0000 (04:35 +0100)]
net: dsa: mv88e6xxx: Implement mv88e6390 tag remap
The mv88e6390 does not have the two registers to set the frame
priority map. Instead it has an indirection registers for setting a
number of different priority maps. Refactor the old code into an
function, implement the mv88e6390 version, and use an op to call the
right one.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 4 Dec 2016 00:29:37 +0000 (19:29 -0500)]
Merge branch 'fib-notifier-event-replay'
Jiri Pirko says:
====================
ipv4: fib: Replay events when registering FIB notifier
Ido says:
In kernel 4.9 the switchdev-specific FIB offload mechanism was replaced
by a new FIB notification chain to which modules could register in order
to be notified about the addition and deletion of FIB entries. The
motivation for this change was that switchdev drivers need to be able to
reflect the entire FIB table and not only FIBs configured on top of the
port netdevs themselves. This is useful in case of in-band management.
The fundamental problem with this approach is that upon registration
listeners lose all the information previously sent in the chain and
thus have an incomplete view of the FIB tables, which can result in
packet loss. This patchset fixes that by dumping the FIB tables and
replaying notifications previously sent in the chain for the registered
notification block.
The entire dump process is done under RCU and thus the FIB notification
chain is converted to be atomic. The listeners are modified accordingly.
This is done in the first eight patches.
The ninth patch adds a change sequence counter to ensure the integrity
of the FIB dump. The last patch adds the dump itself to the FIB chain
registration function and modifies existing listeners to pass a callback
to be executed in case dump was inconsistent.
---
v3->v4:
- Register the notification block after the dump and protect it using
the change sequence counter (Hannes Frederic Sowa).
- Since we now integrate the dump into the registration function, drop
the sysctl to set maximum number of retries and instead set it to a
fixed number. Lets see if it's really a problem before adding something
we can never remove.
- For the same reason, dump FIB tables for all net namespaces.
- Add a comment regarding guarantees provided by mutex semantics.
v2->v3:
- Add sysctl to set the number of FIB dump retries (Hannes Frederic Sowa).
- Read the sequence counter under RTNL to ensure synchronization
between the dump process and other processes changing the routing
tables (Hannes Frederic Sowa).
- Pass a callback to the dump function to be executed prior to a retry.
- Limit the dump to a single net namespace.
v1->v2:
- Add a sequence counter to ensure the integrity of the FIB dump
(David S. Miller, Hannes Frederic Sowa).
- Protect notifications from re-ordering in listeners by using an
ordered workqueue (Hannes Frederic Sowa).
- Introduce fib_info_hold() (Jiri Pirko).
- Relieve rocker from the need to invoke the FIB dump by registering
to the FIB notification chain prior to ports creation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Sat, 3 Dec 2016 15:45:07 +0000 (16:45 +0100)]
ipv4: fib: Replay events when registering FIB notifier
Commit b90eb7549499 ("fib: introduce FIB notification infrastructure")
introduced a new notification chain to notify listeners (f.e., switchdev
drivers) about addition and deletion of routes.
However, upon registration to the chain the FIB tables can already be
populated, which means potential listeners will have an incomplete view
of the tables.
Solve that by dumping the FIB tables and replaying the events to the
passed notification block. The dump itself is done using RCU in order
not to starve consumers that need RTNL to make progress.
The integrity of the dump is ensured by reading the FIB change sequence
counter before and after the dump under RTNL. This allows us to avoid
the problematic situation in which the dumping process sends a ENTRY_ADD
notification following ENTRY_DEL generated by another process holding
RTNL.
Callers of the registration function may pass a callback that is
executed in case the dump was inconsistent with current FIB tables.
The number of retries until a consistent dump is achieved is set to a
fixed number to prevent callers from looping for long periods of time.
In case current limit proves to be problematic in the future, it can be
easily converted to be configurable using a sysctl.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Sat, 3 Dec 2016 15:45:06 +0000 (16:45 +0100)]
ipv4: fib: Allow for consistent FIB dumping
The next patch will enable listeners of the FIB notification chain to
request a dump of the FIB tables. However, since RTNL isn't taken during
the dump, it's possible for the FIB tables to change mid-dump, which
will result in inconsistency between the listener's table and the
kernel's.
Allow listeners to know about changes that occurred mid-dump, by adding
a change sequence counter to each net namespace. The counter is
incremented just before a notification is sent in the FIB chain.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Sat, 3 Dec 2016 15:45:04 +0000 (16:45 +0100)]
rocker: Register FIB notifier before creating ports
We can miss FIB notifications sent between the time the ports were
created and the FIB notification block registered.
Instead of receiving these notifications only when they are replayed for
the FIB notification block during registration, just register the
notification block before the ports are created.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Sat, 3 Dec 2016 15:45:02 +0000 (16:45 +0100)]
rocker: Create an ordered workqueue for FIB offload
As explained in the previous commits, we need to process FIB entries
addition / deletion events in FIFO order or otherwise we can have a
mismatch between the kernel's FIB table and the device's.
Create an ordered workqueue for rocker to which these work items will be
submitted to.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Sat, 3 Dec 2016 15:45:01 +0000 (16:45 +0100)]
mlxsw: spectrum_router: Implement FIB offload in deferred work
FIB offload is currently done in process context with RTNL held, but
we're about to dump the FIB tables in RCU critical section, so we can no
longer sleep.
Instead, defer the operation to process context using deferred work. Make
sure fib info isn't freed while the work is queued by taking a reference
on it and releasing it after the operation is done.
Deferring the operation is valid because the upper layers always assume
the operation was successful. If it's not, then the driver-specific
abort mechanism is called and all routed traffic is directed to slow
path.
The work items are submitted to an ordered workqueue to prevent a
mismatch between the kernel's FIB table and the device's.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Sat, 3 Dec 2016 15:45:00 +0000 (16:45 +0100)]
mlxsw: core: Create an ordered workqueue for FIB offload
We're going to start processing FIB entries addition / deletion events
in deferred work. These work items must be processed in the order they
were submitted or otherwise we can have differences between the kernel's
FIB table and the device's.
Solve this by creating an ordered workqueue to which these work items
will be submitted to. Note that we can't simply convert the current
workqueue to be ordered, as EMADs re-transmissions are also processed in
deferred work.
Later on, we can migrate other work items to this workqueue, such as FDB
notification processing and nexthop resolution, since they all take the
same lock anyway.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Sat, 3 Dec 2016 15:44:58 +0000 (16:44 +0100)]
ipv4: fib: Export free_fib_info()
The FIB notification chain is going to be converted to an atomic chain,
which means switchdev drivers will have to offload FIB entries in
deferred work, as hardware operations entail sleeping.
However, while the work is queued fib info might be freed, so a
reference must be taken. To release the reference (and potentially free
the fib info) fib_info_put() will be called, which in turn calls
free_fib_info().
Export free_fib_info() so that modules will be able to invoke
fib_info_put().
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
WANG Cong [Sat, 3 Dec 2016 18:36:01 +0000 (10:36 -0800)]
act_mirred: fix a typo in get_dev
Fixes: 255cb30425c0 ("net/sched: act_mirred: Add new tc_action_ops get_dev()") Cc: Hadar Hen Zion <hadarh@mellanox.com> Cc: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 4 Dec 2016 00:10:48 +0000 (19:10 -0500)]
Merge branch '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-12-02
This series contains updates to i40e and i40evf only.
Alex provides changes so that we are much more robust about defining what
we can and cannot offload in i40e and i40evf by doing additional checks
other than L4 tunnel header length.
Jake provides several fixes/changes, first cleaning up a label that is
unnecessary, as well as cleaned up the use of a "magic number". Clarified
the code by separating the global private flags and the regular private
flags per interface into two arrays, so that future additions will not
produce duplication and buggy code. Adds additional checks to protect
against NULL values for msix_entries and q_vectors pointers.
Michal adds Clause22 method for accessing registers for some external
PHYs.
Piotr adds additional protocol support for the admin queue discover
capabilities function.
Tushar Dave fixes a panic seen on SPARC, where writel() should not be
used to write directly to a memory address but only to a memory mapped
I/O address otherwise it causes data access exceptions.
Joe Perches separates out a section of code into its own function, to
help reduce i40evf_reset_task() a bit.
Alan fixes an issue by checking for NULL before dereferencing msix_entries
and returning early in the case where it is NULL within the i40evf_close()
code path.
Henry provides code cleanup to remove unreachable and redundant sections
of code. Fixed up an issue where new NICs were not identifying "unknown
PHYs" correctly.
Harshitha fixes a issue where the ethtool "Supported Link" modes list
backplane interfaces on X722 devices for 10 GbE with SFP+ and Cortina
retimer, where these interfaces should not be visible to the user since
they cannot use them.
Carolyn changes an X722 informational message so that it only appears
when extra messages are desired.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuchung Cheng [Sat, 3 Dec 2016 22:46:22 +0000 (14:46 -0800)]
tcp: fix the missing avr32 SOF_TIMESTAMPING_OPT_STATS
The commit of SOF_TIMESTAMPING_OPT_STATS didn't include the
new header for avr32, causing build to break. The patch fixes it.
Fixes: 1c885808e456 ("tcp: SOF_TIMESTAMPING_OPT_STATS option for SO_TIMESTAMPING") Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Fri, 2 Dec 2016 16:35:49 +0000 (17:35 +0100)]
udp: be less conservative with sock rmem accounting
Before commit 850cbaddb52d ("udp: use it's own memory accounting
schema"), the udp protocol allowed sk_rmem_alloc to grow beyond
the rcvbuf by the whole current packet's truesize. After said commit
we allow sk_rmem_alloc to exceed the rcvbuf only if the receive queue
is empty. As reported by Jesper this cause a performance regression
for some (small) values of rcvbuf.
This commit is intended to fix the regression restoring the old
handling of the rcvbuf limit.
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com> Fixes: 850cbaddb52d ("udp: use it's own memory accounting schema") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 2 Dec 2016 16:11:00 +0000 (08:11 -0800)]
net_sched: gen_estimator: account for timer drifts
Under heavy stress, timer used in estimators tend to slowly be delayed
by a few jiffies, leading to inaccuracies.
Lets remember what was the last scheduled jiffies so that we get more
precise estimations, without having to add a multiply/divide in the loop
to account for the drifts.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Edward Cree [Fri, 2 Dec 2016 15:51:33 +0000 (15:51 +0000)]
sfc: remove EFX_BUG_ON_PARANOID, use EFX_WARN_ON_[ONCE_]PARANOID instead
Logically, EFX_BUG_ON_PARANOID can never be correct. For, BUG_ON should
only be used if it is not possible to continue without potential harm;
and since the non-DEBUG driver will continue regardless (as the BUG_ON is
compiled out), clearly the BUG_ON cannot be needed in the DEBUG driver.
So, replace every EFX_BUG_ON_PARANOID with either an EFX_WARN_ON_PARANOID
or the newly defined EFX_WARN_ON_ONCE_PARANOID.
Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 3 Dec 2016 21:08:01 +0000 (16:08 -0500)]
Merge branch 'samples-bpf-automated-cgroup-tests'
Sargun Dhillon says:
====================
samples, bpf: Refactor; Add automated tests for cgroups
These two patches are around refactoring out some old, reusable code from the
existing test_current_task_under_cgroup_user test, and adding a new, automated
test.
There is some generic cgroupsv2 setup & cleanup code, given that most
environment still don't have it setup by default. With this code, we're able
to pretty easily add an automated test for future cgroupsv2 functionality.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sargun Dhillon [Fri, 2 Dec 2016 10:42:32 +0000 (02:42 -0800)]
samples, bpf: Add automated test for cgroup filter attachments
This patch adds the sample program test_cgrp2_attach2. This program is
similar to test_cgrp2_attach, but it performs automated testing of the
cgroupv2 BPF attached filters. It runs the following checks:
* Simple filter attachment
* Application of filters to child cgroups
* Overriding filters on child cgroups
* Checking that this still works when the parent filter is removed
The filters that are used here are simply allow all / deny all filters, so
it isn't checking the actual functionality of the filters, but rather
the behaviour around detachment / attachment. If net_cls is enabled,
this test will fail.
Signed-off-by: Sargun Dhillon <sargun@sargun.me> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Sargun Dhillon [Fri, 2 Dec 2016 10:42:18 +0000 (02:42 -0800)]
samples, bpf: Refactor test_current_task_under_cgroup - separate out helpers
This patch modifies test_current_task_under_cgroup_user. The test has
several helpers around creating a temporary environment for cgroup
testing, and moving the current task around cgroups. This set of
helpers can then be used in other tests.
Signed-off-by: Sargun Dhillon <sargun@sargun.me> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
silence some of the clang compiler warnings like:
include/linux/fs.h:2693:9: warning: comparison of unsigned enum expression < 0 is always false
arch/x86/include/asm/processor.h:491:30: warning: taking address of packed member 'sp0' of class or structure 'x86_hw_tss' may result in an unaligned pointer value
include/linux/cgroup-defs.h:326:16: warning: field 'cgrp' with variable sized type 'struct cgroup' not at the end of a struct or class is a GNU extension
since they add too much noise to samples/bpf/ build.
Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Dobriyan [Fri, 2 Dec 2016 01:21:32 +0000 (04:21 +0300)]
netns: fix net_generic() "id - 1" bloat
net_generic() function is both a) inline and b) used ~600 times.
It has the following code inside
...
ptr = ng->ptr[id - 1];
...
"id" is never compile time constant so compiler is forced to subtract 1.
And those decrements or LEA [r32 - 1] instructions add up.
We also start id'ing from 1 to catch bugs where pernet sybsystem id
is not initialized and 0. This is quite pointless idea (nothing will
work or immediate interference with first registered subsystem) in
general but it hints what needs to be done for code size reduction.
Namely, overlaying allocation of pointer array and fixed part of
structure in the beginning and using usual base-0 addressing.
Ids are just cookies, their exact values do not matter, so lets start
with 3 on x86_64.
Code size savings (oh boy): -4.2 KB
As usual, ignore the initial compiler stupidity part of the table.
This bug was introduced with commit dec827d174d7f76c457238800183ca864a639365
("[NETNS]: The generic per-net pointers.") in the glorious days of
chopping networking stack into containers proper 8.5 years ago (whee...)
How it didn't trigger for so long?
Well, you need quite specific set of conditions:
*) race window opens once per pernet subsystem addition
(read: modprobe or boot)
*) not every pernet subsystem is eligible (need ->id and ->size)
*) not every pernet subsystem is vulnerable (need incorrect or absense
of ordering of register_pernet_sybsys() and actually using net_generic())
*) to hide the bug even more, default is to preallocate 13 pointers which
is actually quite a lot. You need IPv6, netfilter, bridging etc together
loaded to trigger reallocation in the first place. Trimmed down
config are OK.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Dobriyan [Fri, 2 Dec 2016 00:59:06 +0000 (03:59 +0300)]
netlink: 2-clause nla_ok()
nla_ok() consists of 3 clauses:
1) int rem >= (int)sizeof(struct nlattr)
2) u16 nla_len >= sizeof(struct nlattr)
3) u16 nla_len <= int rem
The statement is that clause (1) is redundant.
What it does is ensuring that "rem" is a positive number,
so that in clause (3) positive number will be compared to positive number
with no problems.
However, "u16" fully fits into "int" and integers do not change value
when upcasting even to signed type. Negative integers will be rejected
by clause (3) just fine. Small positive integers will be rejected
by transitivity of comparison operator.
NOTE: all of the above DOES NOT apply to nlmsg_ok() where ->nlmsg_len is
u32(!), so 3 clauses AND A CAST TO INT are necessary.
Zhang Shengju [Fri, 2 Dec 2016 01:51:07 +0000 (09:51 +0800)]
staging: wilc1000: use reset to set mac header
Since offset is zero, it's not necessary to use set function. Reset
function is straightforward, and will remove the unnecessary add
operation in set function.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Zhang Shengju [Fri, 2 Dec 2016 01:51:06 +0000 (09:51 +0800)]
iwlwifi: use reset to set transport header
Since offset is zero, it's not necessary to use set function. Reset
function is straightforward, and will remove the unnecessary add
operation in set function.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Zhang Shengju [Fri, 2 Dec 2016 01:51:05 +0000 (09:51 +0800)]
mlx4: use reset to set mac header
Since offset is zero, it's not necessary to use set function. Reset
function is straightforward, and will remove the unnecessary add
operation in set function.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Zhang Shengju [Fri, 2 Dec 2016 01:51:04 +0000 (09:51 +0800)]
bnx2x: use reset to set network header
Since offset is zero, it's not necessary to use set function. Reset
function is straightforward, and will remove the unnecessary add
operation in set function.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Zhang Shengju [Fri, 2 Dec 2016 01:51:03 +0000 (09:51 +0800)]
qede: use reset to set network header
Since offset is zero, it's not necessary to use set function. Reset
function is straightforward, and will remove the unnecessary add
operation in set function.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com> Acked-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds get_pauseparam and set_pauseparam functions.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com> Signed-off-by: Quan Nguyen <qnguyen@apm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
drivers: net: xgene: Add flow control initialization
This patch adds flow control/pause frame initialization and
advertising capabilities.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com> Signed-off-by: Quan Nguyen <qnguyen@apm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
drivers: net: xgene: Add flow control configuration
This patch adds functions to configure mac, when flow control
and pause frame settings change.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com> Signed-off-by: Quan Nguyen <qnguyen@apm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes RSS feature, for non-TCP/UDP packets.
Signed-off-by: Khuong Dinh <kdinh@apm.com> Signed-off-by: Iyappan Subramanian <isubramanian@apm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements ndo_change_mtu() callback function that
enables mtu change.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com> Signed-off-by: Quan Nguyen <qnguyen@apm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for jumbo frame, by allocating
additional buffer (page) pool and configuring the hardware.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com> Signed-off-by: Quan Nguyen <qnguyen@apm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
drivers: net: xgene: Configure classifier with pagepool
This patch configures classifier with the pagepool information.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com> Signed-off-by: Quan Nguyen <qnguyen@apm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This is a prepartion patch and adds xgene_enet_get_fpsel() helper
function to get buffer pool number.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com> Signed-off-by: Quan Nguyen <qnguyen@apm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
As of commit 8f32b90981dcdb355516fb95953133f8d4e6b11d
("net: ethernet: ti: davinci_cpdma: add set rate for a channel") the
ARM allmodconfig builds would fail modpost with:
Since these weren't declared as static, it is assumed they were
meant to be shared outside the file, and that modular build testing
was simply overlooked.
Fixes: 8f32b90981dc ("net: ethernet: ti: davinci_cpdma: add set rate for a channel") Cc: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Cc: Mugunthan V N <mugunthanvnm@ti.com> Cc: Grygorii Strashko <grygorii.strashko@ti.com> Cc: linux-omap@vger.kernel.org Cc: netdev@vger.kernel.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
this is a pull request of 4 patches for net-next/master.
There are two patches by Chris Paterson for the rcar_can and rcar_canfd
device tree binding documentation. And a patch by Geert Uytterhoeven
that corrects the order of interrupt specifiers.
The fourth patch by Colin Ian King fixes a spelling error in the
kvaser_usb driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
LABBE Corentin [Thu, 1 Dec 2016 15:19:41 +0000 (16:19 +0100)]
net: stmmac: unify mdio functions
stmmac_mdio_{read|write} and stmmac_mdio_{read|write}_gmac4 are not
enought different for being split.
The only differences between thoses two functions are shift/mask for
addr/reg/clk_csr.
This patch introduce a per platform set of variable for setting thoses
shift/mask and unify mdio read and write functions.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
LABBE Corentin [Thu, 1 Dec 2016 15:19:40 +0000 (16:19 +0100)]
net: stmmac: avoid Camelcase naming
This patch simply rename regValue to value, like it was named in other
mdio functions.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Mon, 28 Nov 2016 14:19:43 +0000 (15:19 +0100)]
irda: w83977af_ir: fix damaged whitespace
As David Miller pointed out for for the previous patch, the whitespace
in some functions looks rather odd. This was caused by commit 6329da5f258a
("obsolete config in kernel source: USE_INTERNAL_TIMER"), which removed
some conditions but did not reindent the code.
This fixes the indentation in the file and removes extraneous whitespace
at the end of the lines and before tabs.
There are many other minor coding style problems in the driver, but I'm
not touching those here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
1) In the MACB driver, a bug fix to properly initialize the
RX tail pointer properly overlapped with some changes
to support variable sized rings.
2) In XGBE we had a "CONFIG_PM" --> "CONFIG_PM_SLEEP" fix
overlapping with a reorganization of the driver to support
ACPI, OF, as well as PCI variants of the chip.
3) In 'net' we had several probe error path bug fixes to the
stmmac driver, meanwhile a lot of this code was cleaned up
and reorganized in 'net-next'.
4) The cls_flower classifier obtained a helper function in
'net-next' called __fl_delete() and this overlapped with
Daniel Borkamann's bug fix to use RCU for object destruction
in 'net'. It also overlapped with Jiri's change to guard
the rhashtable_remove_fast() call with a check against
tc_skip_sw().
5) In mlx4, a revert bug fix in 'net' overlapped with some
unrelated changes in 'net-next'.
6) In geneve, a stale header pointer after pskb_expand_head()
bug fix in 'net' overlapped with a large reorganization of
the same code in 'net-next'. Since the 'net-next' code no
longer had the bug in question, there was nothing to do
other than to simply take the 'net-next' hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>
Carolyn Wyborny [Tue, 8 Nov 2016 21:05:12 +0000 (13:05 -0800)]
i40e: change message to only appear when extra debug info is wanted
This patch changes an X722 informational message so that it only
appears when extra messages are desired. Without this patch,
on X722 devices, this message appears at load, potentially causing
unnecessary alarm.
Change-ID: I94f7aae15dc5b2723cc9728c630c72538a3e670e Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Tue, 8 Nov 2016 21:05:11 +0000 (13:05 -0800)]
i40e/i40evf: replace for memcpy with single memcpy call in ethtool
memcpy replaced with single memcpy call in ethtool.
Change-ID: I3f5bef6bcc593412c56592c6459784db41575a0a Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Tue, 8 Nov 2016 21:05:10 +0000 (13:05 -0800)]
i40e: set broadcast promiscuous mode for each active VLAN
A previous workaround added to ensure receipt of all broadcast frames
incorrectly set the broadcast promiscuous mode unconditionally
regardless of active VLAN status.
Replace this partial workaround with a complete solution that sets the
broadcast promiscuous filters in i40e_sync_vsi_filters. This new method
sets the promiscuous mode based on when broadcast filters are added or
removed.
I40E_VLAN_ANY will request a broadcast filter for all VLANs, (as we're
in untagged mode) while a broadcast filter on a specific VLAN will only
request broadcast for that VLAN.
Thus, we restore addition of broadcast filter to the array, but we add
special handling for these such that they enable the broadcast
promiscuous mode instead of being sent as regular filters.
The end result is that we will correctly receive all broadcast packets
(even those with a *source* address equal to the broadcast address) but
will not receive packets for which we don't have an active VLAN filter.
Change-ID: I7d0585c5cec1a5bf55bf533b42e5e817d5db6a2d Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the problem where the ethtool Supported link
modes list backplane interfaces on X722 devices for 10GbE with
SFP+ and Cortina retimer. This patch fixes the problem by setting
and using a flag for this particular device since the backplane
interface is only between the internal PHY and the retimer and it
should not be seen by the user as they cannot use it.
Without this patch, the user wrongly thinks that backplane interfaces
are supported on their device when they actually are not.
Change-ID: I3882bc2928431d48a2db03a51a713a1f681a79e9 Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Tue, 8 Nov 2016 21:05:08 +0000 (13:05 -0800)]
i40evf: protect against NULL msix_entries and q_vectors pointers
Update the functions which free msix_entries and q_vectors so that they
are safe against NULL values. This allows calling code to not care
whether these have already been freed when disabling and freeing them.
Change-ID: I31bfd1c0da18023d971b618edc6fb049721f3298 Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Henry Tieman [Tue, 8 Nov 2016 21:05:07 +0000 (13:05 -0800)]
i40e: Pass unknown PHY type for unknown PHYs
The PHY type value for unrecognized PHYs and cables was changed
based on firmware version number. Newer hardware use lower firmware
version numbers and this was causing some PHYs to be identified
as type 0x16 instead of 0xe (unknown).
Without this patch, newer card will incorrectly identify unknown
PHYs and cables.
This change adds hardware type to the check for firmware version
so the PHY type is reported correctly.
Change-ID: I0723cbfd263c76fc73ff1a5275d1639051376c9a Signed-off-by: Henry Tieman <henry.w.tieman@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Henry Tieman [Tue, 8 Nov 2016 21:05:06 +0000 (13:05 -0800)]
i40e: Remove unreachable code
The code at the end of i40e_read_phy_register_clause22() contained
unreachable code and redundant control statements.
This change removes the unreachable code. And deletes the redundant
goto statement and if statement.
Change-ID: I713032b1585396f40f903cbcfdea987abd874400 Signed-off-by: Henry Tieman <henry.w.tieman@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alan Brady [Tue, 8 Nov 2016 21:05:05 +0000 (13:05 -0800)]
i40evf: check for msix_entries null dereference
It is possible for msix_entries to be freed by a previous suspend/remove
before a VF is closed. This patch fixes the issue by checking for NULL
before dereferencing msix_entries and returning early in the case where
it is NULL within the i40evf_close code path. Without this patch it is
possible to trigger a kernel panic through NULL dereference.
Change-ID: I92a2746e82533a889e25f91578eac9abd0388ae2 Signed-off-by: Alan Brady <alan.brady@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Joe Perches [Tue, 1 Nov 2016 22:35:14 +0000 (15:35 -0700)]
i40evf: Move some i40evf_reset_task code to separate function
The i40evf_reset_task function is a couple hundred lines and it has
a separable block that disables VF. Move that block to a new
i40evf_disable_vf function to shorten i40evf_reset_task a bit.
Signed-off-by: Joe Perches <joe@perches.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tushar Dave [Wed, 26 Oct 2016 17:49:27 +0000 (10:49 -0700)]
i40e: fix panic on SPARC while changing num of desc
On SPARC, writel() should not be used to write directly to memory
address but only to memory mapped I/O address otherwise it causes
data access exception.
Commit 147e81ec75689 ("i40e: Test memory before ethtool alloc
succeeds") introduced a code that uses memory address to fake the HW
tail address and attempt to write to that address using writel()
causes kernel panic on SPARC. The issue is reproduced while changing
number of descriptors using ethtool.
This change resolves the panic by using HW read-only memory mapped
I/O register to fake HW tail address instead memory address.
Signed-off-by: Tushar Dave <tushar.n.dave@oracle.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Piotr Raczynski [Tue, 25 Oct 2016 23:08:53 +0000 (16:08 -0700)]
i40e: Add protocols over MCTP to i40e_aq_discover_capabilities
Add logical_id to I40E_AQ_CAP_ID_MNG_MODE capability starting from major
version 2.
Change-ID: Idb29214b172ea5c70cbd45a99e6745c0215af7e4 Signed-off-by: Piotr Raczynski <piotr.raczynski@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Tue, 25 Oct 2016 23:08:52 +0000 (16:08 -0700)]
i40e: fix trivial typo in naming of i40e_sync_filters_subtask
A comment incorrectly referred to i40e_vsi_sync_filters_subtask which
does not actually exist. Reference the correct function instead.
Change-ID: I6bd805c605741ffb6fe34377259bb0d597edfafd Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Michal Kosiarz [Tue, 25 Oct 2016 23:08:51 +0000 (16:08 -0700)]
i40e: Add Clause22 implementation
Some external PHYs require Clause22 method for accessing registers.
This patch also adds some defines to support blink led on devices using
10CBaseT PHY.
Change-ID: I868a4326911900f6c89e7e522fda4968b0825f14 Signed-off-by: Michal Kosiarz <michal.kosiarz@intel.com> Signed-off-by: Matt Jared <matthew.a.jared@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Tue, 25 Oct 2016 23:08:50 +0000 (16:08 -0700)]
i40e: avoid duplicate private flags definitions
Separate the global private flags and the regular private flags per
interface into two arrays. Future additions of private flags will not
need to be duplicated which may lead to buggy code. Also rename
"i40e_priv_flags_strings_gl" to "i40e_gl_priv_flags_strings" for
clarity, as it reads more naturally.
Change-ID: I68caef3c9954eb7da342d7f9d20f2873186f2758 Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Tue, 25 Oct 2016 23:08:49 +0000 (16:08 -0700)]
i40e: remove second check of VLAN_N_VID in i40e_vlan_rx_add_vid
Replace a check of magic number 4095 with VLAN_N_VID. This
makes it obvious that a later check against VLAN_N_VID is
always true and can be removed.
Change-ID: I28998f127a61a529480ce63d8a07e266f6c63b7b Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Tue, 25 Oct 2016 23:08:48 +0000 (16:08 -0700)]
i40e: remove error_param_int label from i40e_vc_config_promiscuous_mode_msg
This label is unnecessary, as are jumping to a block that checks aq_ret
and then immediately skipping it and returning. So just jump straight to
the error_param and remove this unnecessary label.
Also use goto error_param even in the last check for style consistency.
Change-ID: If487c7d10c4048e37c594e5eca167693aaed45f6 Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Tue, 25 Oct 2016 23:08:47 +0000 (16:08 -0700)]
i40evf: Be much more verbose about what we can and cannot offload
This change makes it so that we are much more robust about defining what we
can and cannot offload. Previously we were performing no checks. This
should bring us up to parity with the i40e PF driver.
In addition the device only supports GSO as long as the MSS is 64 or
greater. We were not checking this so an MSS less than that was resulting
in Tx hangs.
Change-ID: If533553ec92fc6ba694eab6ac81fdaf3004f3592 Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Tue, 25 Oct 2016 23:08:46 +0000 (16:08 -0700)]
i40e: Be much more verbose about what we can and cannot offload
This change makes it so that we are much more robust about defining what we
can and cannot offload. Previously we were just checking for the L4 tunnel
header length, however there are other fields we should be verifying as
there are multiple scenarios in which we cannot perform hardware offloads.
In addition the device only supports GSO as long as the MSS is 64 or
greater. We were not checking this so an MSS less than that was resulting
in Tx hangs.
Change-ID: I5e2fd5f3075c73601b4b36327b771c64fcb6c31b Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Linus Torvalds [Fri, 2 Dec 2016 21:34:37 +0000 (13:34 -0800)]
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"This should be the last set of bugfixes for arm-soc in v4.9. None of
these are critical regressions, but it would be nice to still get them
merged.
- On the Juno platform, the idle latency was described wrong, leading
to suboptimal cpuidle tuning.
- Also on the same platform, PCI I/O space was set up incorrectly and
could not work.
- On the sti platform, a syntactically incorrect DT entry caused
warnings.
- The newly added 'gr8' platform has somewhat confusing file names,
which we rename for consistency"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: dts: juno: fix cluster sleep state entry latency on all SoC versions
arm64: dts: juno: Correct PCI IO window
ARM: dts: STiH407-family: fix i2c nodes
ARM: gr8: Rename the DTSI and relevant DTS
1) Lots more phydev and probe error path leaks in various drivers by
Johan Hovold.
2) Fix race in packet_set_ring(), from Philip Pettersson.
3) Use after free in dccp_invalid_packet(), from Eric Dumazet.
4) Signnedness overflow in SO_{SND,RCV}BUFFORCE, also from Eric
Dumazet.
5) When tunneling between ipv4 and ipv6 we can be left with the wrong
skb->protocol value as we enter the IPSEC engine and this causes all
kinds of problems. Set it before the output path does any
dst_output() calls, from Eli Cooper.
6) bcmgenet uses wrong device struct pointer in DMA API calls, fix from
Florian Fainelli.
7) Various netfilter nat bug fixes from FLorian Westphal.
8) Fix memory leak in ipvlan_link_new(), from Gao Feng.
9) Locking fixes, particularly wrt. socket lookups, in l2tp from
Guillaume Nault.
10) Avoid invoking rhash teardowns in atomic context by moving netlink
cb->done() dump completion from a worker thread. Fix from Herbert
Xu.
11) Buffer refcount problems in tun and macvtap on errors, from Jason
Wang.
12) We don't set Kconfig symbol DEFAULT_TCP_CONG properly when the user
selects BBR. Fix from Julian Wollrath.
13) Fix deadlock in transmit path on altera TSE driver, from Lino
Sanfilippo.
14) Fix unbalanced reference counting in dsa_switch_tree, from Nikita
Yushchenko.
15) tc_tunnel_key needs to be properly exported to userspace via uapi,
fix from Roi Dayan.
16) rds_tcp_init_net() doesn't unregister notifier in error path, fix
from Sowmini Varadhan.
17) Stale packet header pointer access after pskb_expand_head() in
genenve driver, fix from Sabrina Dubroca.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (103 commits)
net: avoid signed overflows for SO_{SND|RCV}BUFFORCE
geneve: avoid use-after-free of skb->data
tipc: check minimum bearer MTU
net: renesas: ravb: unintialized return value
sh_eth: remove unchecked interrupts for RZ/A1
net: bcmgenet: Utilize correct struct device for all DMA operations
NET: usb: qmi_wwan: add support for Telit LE922A PID 0x1040
cdc_ether: Fix handling connection notification
ip6_offload: check segs for NULL in ipv6_gso_segment.
RDS: TCP: unregister_netdevice_notifier() in error path of rds_tcp_init_net
Revert: "ip6_tunnel: Update skb->protocol to ETH_P_IPV6 in ip6_tnl_xmit()"
ipv6: Set skb->protocol properly for local output
ipv4: Set skb->protocol properly for local output
packet: fix race condition in packet_set_ring
net: ethernet: altera: TSE: do not use tx queue lock in tx completion handler
net: ethernet: altera: TSE: Remove unneeded dma sync for tx buffers
net: ethernet: stmmac: fix of-node and fixed-link-phydev leaks
net: ethernet: stmmac: platform: fix outdated function header
net: ethernet: stmmac: dwmac-meson8b: fix probe error path
net: ethernet: stmmac: dwmac-generic: fix probe error path
...
Eric Dumazet [Fri, 2 Dec 2016 17:44:53 +0000 (09:44 -0800)]
net: avoid signed overflows for SO_{SND|RCV}BUFFORCE
CAP_NET_ADMIN users should not be allowed to set negative
sk_sndbuf or sk_rcvbuf values, as it can lead to various memory
corruptions, crashes, OOM...
Note that before commit 82981930125a ("net: cleanups in
sock_setsockopt()"), the bug was even more serious, since SO_SNDBUF
and SO_RCVBUF were vulnerable.
This needs to be backported to all known linux kernels.
Again, many thanks to syzkaller team for discovering this gem.
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sabrina Dubroca [Fri, 2 Dec 2016 15:49:29 +0000 (16:49 +0100)]
geneve: avoid use-after-free of skb->data
geneve{,6}_build_skb can end up doing a pskb_expand_head(), which
makes the ip_hdr(skb) reference we stashed earlier stale. Since it's
only needed as an argument to ip_tunnel_ecn_encap(), move this
directly in the function call.
Fixes: 08399efc6319 ("geneve: ensure ECN info is handled properly in all tx/rx paths") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Reviewed-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-eoan-kernel.git / log