Pavel reports that it causes occasional boot hangs for him that seem to
depend on just how the machine was booted. In particular, his machine
hangs at around the PCI fixups of the EHCI USB host controller, but only
hangs from cold boot, not from a warm boot.
Thomas Gleixner suspecs it's a CPU hotplug interaction, particularly
since Pavel also saw suspend/resume issues that seem to be related.
We're reverting for now while trying to figure out the root cause.
Reported-bisected-and-tested-by: Pavel Machek <pavel@ucw.cz> Acked-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Wanpeng Li <wanpeng.li@hotmail.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rik van Riel <riel@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: stable@kernel.org # reverted commits were marked for stable Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Miklos Szeredi [Thu, 16 Feb 2017 16:49:02 +0000 (17:49 +0100)]
vfs: fix uninitialized flags in splice_to_pipe()
Flags (PIPE_BUF_FLAG_PACKET, PIPE_BUF_FLAG_GIFT) could remain on the
unused part of the pipe ring buffer. Previously splice_to_pipe() left
the flags value alone, which could result in incorrect behavior.
Uninitialized flags appears to have been there from the introduction of
the splice syscall.
Linus Torvalds [Thu, 16 Feb 2017 17:05:34 +0000 (09:05 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse
Pull fuse fixes from Miklos Szeredi:
"Fix a use after free bug introduced in 4.2 and using an uninitialized
value introduced in 4.9"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: fix uninitialized flags in pipe_buffer
fuse: fix use after free issue in fuse_dev_do_read()
Linus Torvalds [Thu, 16 Feb 2017 17:03:37 +0000 (09:03 -0800)]
Merge tag 'pci-v4.10-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fix from Bjorn Helgaas:
"Add back pcie_pme_remove() so we free the IRQ when removing PCIe port
devices; previously the leaked IRQ caused an MSI BUG_ON"
* tag 'pci-v4.10-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI/PME: Restore pcie_pme_driver.remove
1) In order to avoid problems in the future, make cgroup bpf overriding
explicit using BPF_F_ALLOW_OVERRIDE. From Alexei Staovoitov.
2) LLC sets skb->sk without proper skb->destructor and this explodes,
fix from Eric Dumazet.
3) Make sure when we have an ipv4 mapped source address, the
destination is either also an ipv4 mapped address or
ipv6_addr_any(). Fix from Jonathan T. Leighton.
4) Avoid packet loss in fec driver by programming the multicast filter
more intelligently. From Rui Sousa.
5) Handle multiple threads invoking fanout_add(), fix from Eric
Dumazet.
6) Since we can invoke the TCP input path in process context, without
BH being disabled, we have to accomodate that in the locking of the
TCP probe. Also from Eric Dumazet.
7) Fix erroneous emission of NETEVENT_DELAY_PROBE_TIME_UPDATE when we
aren't even updating that sysctl value. From Marcus Huewe.
8) Fix endian bugs in ibmvnic driver, from Thomas Falcon.
[ This is the second version of the pull that reverts the nested
rhashtable changes that looked a bit too scary for this late in the
release - Linus ]
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (27 commits)
rhashtable: Revert nested table changes.
ibmvnic: Fix endian errors in error reporting output
ibmvnic: Fix endian error when requesting device capabilities
net: neigh: Fix netevent NETEVENT_DELAY_PROBE_TIME_UPDATE notification
net: xilinx_emaclite: fix freezes due to unordered I/O
net: xilinx_emaclite: fix receive buffer overflow
bpf: kernel header files need to be copied into the tools directory
tcp: tcp_probe: use spin_lock_bh()
uapi: fix linux/if_pppol2tp.h userspace compilation errors
packet: fix races in fanout_add()
ibmvnic: Fix initial MTU settings
net: ethernet: ti: cpsw: fix cpsw assignment in resume
kcm: fix a null pointer dereference in kcm_sendmsg()
net: fec: fix multicast filtering hardware setup
ipv6: Handle IPv4-mapped src to in6addr_any dst.
ipv6: Inhibit IPv4-mapped src address on the wire.
net/mlx5e: Disable preemption when doing TC statistics upcall
rhashtable: Add nested tables
tipc: Fix tipc_sk_reinit race conditions
gfs2: Use rhashtable walk interface in glock_hash_walk
...
Thomas Falcon [Wed, 15 Feb 2017 16:32:11 +0000 (10:32 -0600)]
ibmvnic: Fix endian error when requesting device capabilities
When a vNIC client driver requests a faulty device setting, the
server returns an acceptable value for the client to request.
This 64 bit value was incorrectly being swapped as a 32 bit value,
resulting in loss of data. This patch corrects that by using
the 64 bit swap function.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When setting a neigh related sysctl parameter, we always send a
NETEVENT_DELAY_PROBE_TIME_UPDATE netevent. For instance, when
executing
sysctl net.ipv6.neigh.wlp3s0.retrans_time_ms=2000
a NETEVENT_DELAY_PROBE_TIME_UPDATE netevent is generated.
This is caused by commit 2a4501ae18b5 ("neigh: Send a
notification when DELAY_PROBE_TIME changes"). According to the
commit's description, it was intended to generate such an event
when setting the "delay_first_probe_time" sysctl parameter.
In order to fix this, only generate this event when actually
setting the "delay_first_probe_time" sysctl parameter. This fix
should not have any unintended side-effects, because all but one
registered netevent callbacks check for other netevent event
types (the registered callbacks were obtained by grepping for
"register_netevent_notifier"). The only callback that uses the
NETEVENT_DELAY_PROBE_TIME_UPDATE event is
mlxsw_sp_router_netevent_event() (in
drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c): in case
of this event, it only accesses the DELAY_PROBE_TIME of the
passed neigh_parms.
Fixes: 2a4501ae18b5 ("neigh: Send a notification when DELAY_PROBE_TIME changes") Signed-off-by: Marcus Huewe <suse-tux@gmx.de> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Anssi Hannula [Tue, 14 Feb 2017 17:11:45 +0000 (19:11 +0200)]
net: xilinx_emaclite: fix freezes due to unordered I/O
The xilinx_emaclite uses __raw_writel and __raw_readl for register
accesses. Those functions do not imply any kind of memory barriers and
they may be reordered.
The driver does not seem to take that into account, though, and the
driver does not satisfy the ordering requirements of the hardware.
For clear examples, see xemaclite_mdio_write() and xemaclite_mdio_read()
which try to set MDIO address before initiating the transaction.
I'm seeing system freezes with the driver with GCC 5.4 and current
Linux kernels on Zynq-7000 SoC immediately when trying to use the
interface.
In commit 123c1407af87 ("net: emaclite: Do not use microblaze and ppc
IO functions") the driver was switched from non-generic
in_be32/out_be32 (memory barriers, big endian) to
__raw_readl/__raw_writel (no memory barriers, native endian), so
apparently the device follows system endianness and the driver was
originally written with the assumption of memory barriers.
Rather than try to hunt for each case of missing barrier, just switch
the driver to use iowrite32/ioread32/iowrite32be/ioread32be depending
on endianness instead.
Tested on little-endian Zynq-7000 ARM SoC FPGA.
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi> Fixes: 123c1407af87 ("net: emaclite: Do not use microblaze and ppc IO
functions") Signed-off-by: David S. Miller <davem@davemloft.net>
Anssi Hannula [Tue, 14 Feb 2017 17:11:44 +0000 (19:11 +0200)]
net: xilinx_emaclite: fix receive buffer overflow
xilinx_emaclite looks at the received data to try to determine the
Ethernet packet length but does not properly clamp it if
proto_type == ETH_P_IP or 1500 < proto_type <= 1518, causing a buffer
overflow and a panic via skb_panic() as the length exceeds the allocated
skb size.
Fix those cases.
Also add an additional unconditional check with WARN_ON() at the end.
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi> Fixes: bb81b2ddfa19 ("net: add Xilinx emac lite device driver") Signed-off-by: David S. Miller <davem@davemloft.net>
Yinghai Lu [Wed, 15 Feb 2017 05:17:48 +0000 (21:17 -0800)]
PCI/PME: Restore pcie_pme_driver.remove
In addition to making PME non-modular, d7def2040077 ("PCI/PME: Make
explicitly non-modular") removed the pcie_pme_driver .remove() method,
pcie_pme_remove().
pcie_pme_remove() freed the PME IRQ that was requested in pci_pme_probe().
The fact that we don't free the IRQ after d7def2040077 causes the following
crash when removing a PCIe port device via /sys:
Sahitya Tummala [Wed, 8 Feb 2017 15:00:56 +0000 (20:30 +0530)]
fuse: fix use after free issue in fuse_dev_do_read()
There is a potential race between fuse_dev_do_write()
and request_wait_answer() contexts as shown below:
TASK 1:
__fuse_request_send():
|--spin_lock(&fiq->waitq.lock);
|--queue_request();
|--spin_unlock(&fiq->waitq.lock);
|--request_wait_answer():
|--if (test_bit(FR_SENT, &req->flags))
<gets pre-empted after it is validated true>
TASK 2:
fuse_dev_do_write():
|--clears bit FR_SENT,
|--request_end():
|--sets bit FR_FINISHED
|--spin_lock(&fiq->waitq.lock);
|--list_del_init(&req->intr_entry);
|--spin_unlock(&fiq->waitq.lock);
|--fuse_put_request();
|--queue_interrupt();
<request gets queued to interrupts list>
|--wake_up_locked(&fiq->waitq);
|--wait_event_freezable();
<as FR_FINISHED is set, it returns and then
the caller frees this request>
Now, the next fuse_dev_do_read(), see interrupts list is not empty
and then calls fuse_read_interrupt() which tries to access the request
which is already free'd and gets the below crash:
[11432.401266] Unable to handle kernel paging request at virtual address 6b6b6b6b6b6b6b6b
...
[11432.418518] Kernel BUG at ffffff80083720e0
[11432.456168] PC is at __list_del_entry+0x6c/0xc4
[11432.463573] LR is at fuse_dev_do_read+0x1ac/0x474
...
[11432.679999] [<ffffff80083720e0>] __list_del_entry+0x6c/0xc4
[11432.687794] [<ffffff80082c65e0>] fuse_dev_do_read+0x1ac/0x474
[11432.693180] [<ffffff80082c6b14>] fuse_dev_read+0x6c/0x78
[11432.699082] [<ffffff80081d5638>] __vfs_read+0xc0/0xe8
[11432.704459] [<ffffff80081d5efc>] vfs_read+0x90/0x108
[11432.709406] [<ffffff80081d67f0>] SyS_read+0x58/0x94
As FR_FINISHED bit is set before deleting the intr_entry with input
queue lock in request completion path, do the testing of this flag and
queueing atomically with the same lock in queue_interrupt().
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org> Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Fixes: fd22d62ed0c3 ("fuse: no fc->lock for iqueue parts") Cc: <stable@vger.kernel.org> # 4.2+
Stephen Rothwell [Mon, 13 Feb 2017 21:22:20 +0000 (08:22 +1100)]
bpf: kernel header files need to be copied into the tools directory
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 15 Feb 2017 01:11:14 +0000 (17:11 -0800)]
tcp: tcp_probe: use spin_lock_bh()
tcp_rcv_established() can now run in process context.
We need to disable BH while acquiring tcp probe spinlock,
or risk a deadlock.
Fixes: 5413d1babe8f ("net: do not block BH while processing socket backlog") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Ricardo Nabinger Sanchez <rnsanchez@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Because of <linux/libc-compat.h> interface limitations, <netinet/in.h>
provided by libc cannot be included after <linux/in.h>, therefore any
header that includes <netinet/in.h> cannot be included after <linux/in.h>.
Change uapi/linux/l2tp.h, the last uapi header that includes
<netinet/in.h>, to include <linux/in.h> and <linux/in6.h> instead of
<netinet/in.h> and use __SOCK_SIZE__ instead of sizeof(struct sockaddr)
the same way as uapi/linux/in.h does, to fix linux/if_pppol2tp.h userspace
compilation errors like this:
In file included from /usr/include/linux/l2tp.h:12:0,
from /usr/include/linux/if_pppol2tp.h:21,
/usr/include/netinet/in.h:31:8: error: redefinition of 'struct in_addr'
Fixes: 47c3e7783be4 ("net: l2tp: deprecate PPPOL2TP_MSG_* in favour of L2TP_MSG_*") Signed-off-by: Dmitry V. Levin <ldv@altlinux.org> Signed-off-by: David S. Miller <davem@davemloft.net>
[media] siano: make it work again with CONFIG_VMAP_STACK
Reported as a Kaffeine bug:
https://bugs.kde.org/show_bug.cgi?id=375811
The USB control messages require DMA to work. We cannot pass
a stack-allocated buffer, as it is not warranted that the
stack would be into a DMA enabled area.
On Kernel 4.9, the default is to not accept DMA on stack anymore
on x86 architecture. On other architectures, this has been a
requirement since Kernel 2.2. So, after this patch, this driver
should likely work fine on all archs.
Eric Dumazet [Tue, 14 Feb 2017 17:03:51 +0000 (09:03 -0800)]
packet: fix races in fanout_add()
Multiple threads can call fanout_add() at the same time.
We need to grab fanout_mutex earlier to avoid races that could
lead to one thread freeing po->rollover that was set by another thread.
Do the same in fanout_release(), for peace of mind, and to help us
finding lockdep issues earlier.
Fixes: dc99f600698d ("packet: Add fanout support.") Fixes: 0648ab70afe6 ("packet: rollover prepare: per-socket state") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Falcon [Tue, 14 Feb 2017 16:22:59 +0000 (10:22 -0600)]
ibmvnic: Fix initial MTU settings
In the current driver, the MTU is set to the maximum value
capable for the backing device. This decision turned out to
be a mistake as it led to confusion among users. The expected
initial MTU value used for other IBM vNIC capable operating
systems is 1500, with the maximum value (9000) reserved for
when Jumbo frames are enabled. This patch sets the MTU to
the default value for a net device.
It also corrects a discrepancy between MTU values received from
firmware, which includes the ethernet header length, and net
device MTU values.
Finally, it removes redundant min/max MTU assignments after device
initialization.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Khoronzhuk [Tue, 14 Feb 2017 12:42:15 +0000 (14:42 +0200)]
net: ethernet: ti: cpsw: fix cpsw assignment in resume
There is a copy-paste error, which hides breaking of resume
for CPSW driver: there was replaced netdev_priv() to ndev_to_cpsw(ndev)
in suspend, but left it unchanged in resume.
Fixes: 606f39939595a4d4540406bfc11f265b2036af6d
(ti: cpsw: move platform data and slaves info to cpsw_common)
Reported-by: Alexey Starikovskiy <AStarikovskiy@topcon.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
WANG Cong [Mon, 13 Feb 2017 19:13:16 +0000 (11:13 -0800)]
kcm: fix a null pointer dereference in kcm_sendmsg()
In commit 98e3862ca2b1 ("kcm: fix 0-length case for kcm_sendmsg()")
I tried to avoid skb allocation for 0-length case, but missed
a check for NULL pointer in the non EOR case.
Fixes: 98e3862ca2b1 ("kcm: fix 0-length case for kcm_sendmsg()") Reported-by: Dmitry Vyukov <dvyukov@google.com> Cc: Tom Herbert <tom@herbertland.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rui Sousa [Mon, 13 Feb 2017 02:01:25 +0000 (10:01 +0800)]
net: fec: fix multicast filtering hardware setup
Fix hardware setup of multicast address hash:
- Never clear the hardware hash (to avoid packet loss)
- Construct the hash register values in software and then write once
to hardware
Signed-off-by: Rui Sousa <rui.sousa@nxp.com> Signed-off-by: Fugang Duan <fugang.duan@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 14 Feb 2017 17:13:52 +0000 (12:13 -0500)]
Merge branch 'ipv6-v4mapped'
Jonathan T. Leighton says:
====================
IPv4-mapped on wire, :: dst address issue
Under some circumstances IPv6 datagrams are sent with IPv4-mapped IPv6
addresses as the source. Given an IPv6 socket bound to an IPv4-mapped
IPv6 address, and an IPv6 destination address, both TCP and UDP will
will send packets using the IPv4-mapped IPv6 address as the source. Per
RFC 6890 (Table 20), IPv4-mapped IPv6 source addresses are not allowed
in an IP datagram. The problem can be observed by attempting to
connect() either a TCP or UDP socket, or by using sendmsg() with a UDP
socket. The patch is intended to correct this issue for all socket
types.
linux follows the BSD convention that an IPv6 destination address
specified as in6addr_any is converted to the loopback address.
Currently, neither TCP nor UDP consider the possibility that the source
address is an IPv4-mapped IPv6 address, and assume that the appropriate
loopback address is ::1. The patch adds a check on whether or not the
source address is an IPv4-mapped IPv6 address and then sets the
destination address to either ::ffff:127.0.0.1 or ::1, as appropriate.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a check on the type of the source address for the case
where the destination address is in6addr_any. If the source is an
IPv4-mapped IPv6 source address, the destination is changed to
::ffff:127.0.0.1, and otherwise the destination is changed to ::1. This
is done in three locations to handle UDP calls to either connect() or
sendmsg() and TCP calls to connect(). Note that udpv6_sendmsg() delays
handling an in6addr_any destination until very late, so the patch only
needs to handle the case where the source is an IPv4-mapped IPv6
address.
Signed-off-by: Jonathan T. Leighton <jtleight@udel.edu> Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6: Inhibit IPv4-mapped src address on the wire.
This patch adds a check for the problematic case of an IPv4-mapped IPv6
source address and a destination address that is neither an IPv4-mapped
IPv6 address nor in6addr_any, and returns an appropriate error. The
check in done before returning from looking up the route.
Signed-off-by: Jonathan T. Leighton <jtleight@udel.edu> Signed-off-by: David S. Miller <davem@davemloft.net>
per the kernel documention, preemption should be disabled, add that.
Before the fix, when running with CONFIG_PREEMPT set, we get a
BUG: using smp_processor_id() in preemptible [00000000] code: tc/3793
asserion from the TC action (mirred) stats_update callback.
Fixes: aad7e08d39bd ('net/mlx5e: Hardware offloaded flower filter statistics support') Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 14 Feb 2017 14:29:21 +0000 (06:29 -0800)]
Merge tag 'media/v4.10-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"A colorspace regression fix in V4L2 core and a CEC core bug that makes
it discard valid messages"
* tag 'media/v4.10-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] cec: initiator should be the same as the destination for, poll
[media] videodev2.h: go back to limited range Y'CbCr for SRGB and, ADOBERGB
====================
rhashtable: Handle table allocation failure during insertion
v2 -
Added Ack to patch 2.
Fixed RCU annotation in code path executed by rehasher by using
rht_dereference_bucket.
v1 -
This series tackles the problem of table allocation failures during
insertion. The issue is that we cannot vmalloc during insertion.
This series deals with this by introducing nested tables.
The first two patches removes manual hash table walks which cannot
work on a nested table.
The final patch introduces nested tables.
I've tested this with test_rhashtable and it appears to work.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Sat, 11 Feb 2017 11:26:47 +0000 (19:26 +0800)]
rhashtable: Add nested tables
This patch adds code that handles GFP_ATOMIC kmalloc failure on
insertion. As we cannot use vmalloc, we solve it by making our
hash table nested. That is, we allocate single pages at each level
and reach our desired table size by nesting them.
When a nested table is created, only a single page is allocated
at the top-level. Lower levels are allocated on demand during
insertion. Therefore for each insertion to succeed, only two
(non-consecutive) pages are needed.
After a nested table is created, a rehash will be scheduled in
order to switch to a vmalloced table as soon as possible. Also,
the rehash code will never rehash into a nested table. If we
detect a nested table during a rehash, the rehash will be aborted
and a new rehash will be scheduled.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Sat, 11 Feb 2017 11:26:46 +0000 (19:26 +0800)]
tipc: Fix tipc_sk_reinit race conditions
There are two problems with the function tipc_sk_reinit. Firstly
it's doing a manual walk over an rhashtable. This is broken as
an rhashtable can be resized and if you manually walk over it
during a resize then you may miss entries.
Secondly it's missing memory barriers as previously the code used
spinlocks which provide the barriers implicitly.
This patch fixes both problems.
Fixes: 07f6c4bc048a ("tipc: convert tipc reference table to...") Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Sat, 11 Feb 2017 11:26:45 +0000 (19:26 +0800)]
gfs2: Use rhashtable walk interface in glock_hash_walk
The function glock_hash_walk walks the rhashtable by hand. This
is broken because if it catches the hash table in the middle of
a rehash, then it will miss entries.
This patch replaces the manual walk by using the rhashtable walk
interface.
Fixes: 88ffbf3e037e ("GFS2: Use resizable hash table for glocks") Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Ralf Baechle [Fri, 10 Feb 2017 23:38:57 +0000 (00:38 +0100)]
NET: Fix /proc/net/arp for AX.25
When sending ARP requests over AX.25 links the hwaddress in the neighbour
cache are not getting initialized. For such an incomplete arp entry
ax2asc2 will generate an empty string resulting in /proc/net/arp output
like the following:
To do so it change ax2asc to put the string "*" in buf for a NULL address
argument. Finally the HW address field is left aligned in a 17 character
field (the length of an ethernet HW address in the usual hex notation) for
readability.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Mart van Santen [Fri, 10 Feb 2017 12:02:18 +0000 (12:02 +0000)]
xen-netback: vif counters from int/long to u64
This patch fixes an issue where the type of counters in the queue(s)
and interface are not in sync (queue counters are int, interface
counters are long), causing incorrect reporting of tx/rx values
of the vif interface and unclear counter overflows.
This patch sets both counters to the u64 type.
Signed-off-by: Mart van Santen <mart@greenhost.nl> Reviewed-by: Paul Durrant <paul.durrant@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The ghostprotocols.net domain is not working, remove it from CREDITS and
MAINTAINERS, and change the status to "Odd fixes", and since I haven't
been maintaining those, remove my address from there.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hans Verkuil [Sat, 11 Feb 2017 11:24:46 +0000 (09:24 -0200)]
[media] cec: initiator should be the same as the destination for, poll
Poll messages that are used to allocate a logical address should
use the same initiator as the destination. Instead, it expected that
the initiator was 0xf which is not according to the standard.
This also had consequences for the message checks in cec_transmit_msg_fh
that incorrectly rejected poll messages with the same initiator and
destination.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The problem is that many drivers can convert R'G'B' content (often
from sensors) to Y'CbCr, but they all produce limited range Y'CbCr.
To stay backwards compatible the default quantization range for
sRGB and AdobeRGB Y'CbCr encoding should be limited range, not full
range, even though the corresponding standards specify full range.
Update the V4L2_MAP_QUANTIZATION_DEFAULT define accordingly and
also update the documentation.
Fixes: 7e0739cd9c40 ("[media] videodev2.h: fix sYCC/AdobeYCC default quantization range") Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Cc: <stable@vger.kernel.org> # for v4.9 and up Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Eric Dumazet [Sun, 12 Feb 2017 22:03:52 +0000 (14:03 -0800)]
net/llc: avoid BUG_ON() in skb_orphan()
It seems nobody used LLC since linux-3.12.
Fortunately fuzzers like syzkaller still know how to run this code,
otherwise it would be no fun.
Setting skb->sk without skb->destructor leads to all kinds of
bugs, we now prefer to be very strict about it.
Ideally here we would use skb_set_owner() but this helper does not exist yet,
only CAN seems to have a private helper for that.
Fixes: 376c7311bdb6 ("net: add a temporary sanity check in skb_orphan()") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
If BPF_F_ALLOW_OVERRIDE flag is used in BPF_PROG_ATTACH command
to the given cgroup the descendent cgroup will be able to override
effective bpf program that was inherited from this cgroup.
By default it's not passed, therefore override is disallowed.
Examples:
1.
prog X attached to /A with default
prog Y fails to attach to /A/B and /A/B/C
Everything under /A runs prog X
2.
prog X attached to /A with allow_override.
prog Y fails to attach to /A/B with default (non-override)
prog M attached to /A/B with allow_override.
Everything under /A/B runs prog M only.
3.
prog X attached to /A with allow_override.
prog Y fails to attach to /A with default.
The user has to detach first to switch the mode.
In the future this behavior may be extended with a chain of
non-overridable programs.
Also fix the bug where detach from cgroup where nothing is attached
was not throwing error. Return ENOENT in such case.
Add several testcases and adjust libbpf.
Fixes: 3007098494be ("cgroup: add support for eBPF programs") Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Tejun Heo <tj@kernel.org> Acked-by: Daniel Mack <daniel@zonque.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Nathan Fontenot [Fri, 10 Feb 2017 18:29:06 +0000 (13:29 -0500)]
ibmvnic: Call napi_disable instead of napi_enable in failure path
The failure path in ibmvnic_open() mistakenly makes a second call
to napi_enable instead of calling napi_disable. This can result
in a BUG_ON for any queues that were enabled in the previous call
to napi_enable.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nathan Fontenot [Fri, 10 Feb 2017 18:45:05 +0000 (13:45 -0500)]
ibmvnic: Initialize completion variables before starting work
Initialize condition variables prior to invoking any work that can
mark them complete. This resolves a race in the ibmvnic driver where
the driver faults trying to complete an uninitialized condition
variable.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 11 Feb 2017 18:31:46 +0000 (10:31 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Last minute x86 fixes:
- Fix a softlockup detector warning and long delays if using ptdump
with KASAN enabled.
- Two more TSC-adjust fixes for interesting firmware interactions.
- Two commits to fix an AMD CPU topology enumeration bug that caused
a measurable gaming performance regression"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm/ptdump: Fix soft lockup in page table walker
x86/tsc: Make the TSC ADJUST sanitizing work for tsc_reliable
x86/tsc: Avoid the large time jump when sanitizing TSC ADJUST
x86/CPU/AMD: Fix Zen SMT topology
x86/CPU/AMD: Bring back Compute Unit ID
Linus Torvalds [Sat, 11 Feb 2017 18:24:16 +0000 (10:24 -0800)]
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Ingo Molnar:
"Fix a sporadic missed timer hw reprogramming bug that can result in
random delays"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick/nohz: Fix possible missing clock reprog after tick soft restart
Linus Torvalds [Sat, 11 Feb 2017 18:16:05 +0000 (10:16 -0800)]
Merge branch 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull lockdep fix from Ingo Molnar:
"This fixes an ugly lockdep stack trace output regression. (But also
affects other stacktrace users such as kmemleak, KASAN, etc)"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
stacktrace, lockdep: Fix address, newline ugliness
Linus Torvalds [Sat, 11 Feb 2017 18:14:24 +0000 (10:14 -0800)]
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Ingo Molnar:
"Two last minute ARM irqchip driver fixes"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/mxs: Enable SKIP_SET_WAKE and MASK_ON_SUSPEND
irqchip/keystone: Fix "scheduling while atomic" on rt
Linus Torvalds [Sat, 11 Feb 2017 17:15:58 +0000 (09:15 -0800)]
Merge branch 'for-linus-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"This has two last minute fixes. The highest priority here is a
regression fix for the decompression code, but we also fixed up a
problem with the 32-bit compat ioctls.
The decompression bug could hand back the wrong data on big reads when
zlib was used. I have a larger cleanup to make the math here less
error prone, but at this stage in the release Omar's patch is the best
choice"
* 'for-linus-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: fix btrfs_decompress_buf2page()
btrfs: fix btrfs_compat_ioctl failures on non-compat ioctls
Linus Torvalds [Sat, 11 Feb 2017 17:01:03 +0000 (09:01 -0800)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Six fairly small fixes. None is a real show stopper, two automation
detected problems: one memory leak, one use after free and four others
each of which fixes something that has been a significant source of
annoyance to someone"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: zfcp: fix use-after-free by not tracing WKA port open/close on failed send
scsi: aacraid: Fix INTx/MSI-x issue with older controllers
scsi: mpt3sas: disable ASPM for MPI2 controllers
scsi: mpt3sas: Force request partial completion alignment
scsi: qla2xxx: Avoid that issuing a LIP triggers a kernel crash
scsi: qla2xxx: Fix a recently introduced memory leak
Omar Sandoval [Fri, 10 Feb 2017 23:03:35 +0000 (15:03 -0800)]
Btrfs: fix btrfs_decompress_buf2page()
If btrfs_decompress_buf2page() is handed a bio with its page in the
middle of the working buffer, then we adjust the offset into the working
buffer. After we copy into the bio, we advance the iterator by the
number of bytes we copied. Then, we have some logic to handle the case
of discontiguous pages and adjust the offset into the working buffer
again. However, if we didn't advance the bio to a new page, we may enter
this case in error, essentially repeating the adjustment that we already
made when we entered the function. The end result is bogus data in the
bio.
Previously, we only checked for this case when we advanced to a new
page, but the conversion to bio iterators changed that. This restores
the old, correct behavior.
After bio_advance(), we are still in the same page, so start_byte is the
same. Then, we check (total_out > start_byte && current_buf_start < start_byte),
which is true! So, we adjust the values again:
But note that working_bytes was already zero before this, so we should
have stopped copying.
Fixes: 974b1adc3b10 ("btrfs: use bio iterators for the decompression handlers") Reported-by: Pat Erley <pat-lkml@erley.org> Reviewed-by: Chris Mason <clm@fb.com> Signed-off-by: Omar Sandoval <osandov@fb.com> Signed-off-by: Chris Mason <clm@fb.com> Reviewed-by: Liu Bo <bo.li.liu@oracle.com> Tested-by: Liu Bo <bo.li.liu@oracle.com>
1) If the timing is wrong we can indefinitely stop generating new ipv6
temporary addresses, from Marcus Huewe.
2) Don't double free per-cpu stats in ipv6 SIT tunnel driver, from Cong
Wang.
3) Put protections in place so that AF_PACKET is not able to submit
packets which don't even have a link level header to drivers. From
Willem de Bruijn.
4) Fix memory leaks in ipv4 and ipv6 multicast code, from Hangbin Liu.
5) Don't use udp_ioctl() in l2tp code, UDP version expects a UDP socket
and that doesn't go over very well when it is passed an L2TP one.
Fix from Eric Dumazet.
6) Don't crash on NULL pointer in phy_attach_direct(), from Florian
Fainelli.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
l2tp: do not use udp_ioctl()
xen-netfront: Delete rx_refill_timer in xennet_disconnect_backend()
NET: mkiss: Fix panic
net: hns: Fix the device being used for dma mapping during TX
net: phy: Initialize mdio clock at probe function
igmp, mld: Fix memory leak in igmpv3/mld_del_delrec()
xen-netfront: Improve error handling during initialization
sierra_net: Skip validating irrelevant fields for IDLE LSIs
sierra_net: Add support for IPv6 and Dual-Stack Link Sense Indications
kcm: fix 0-length case for kcm_sendmsg()
xen-netfront: Rework the fix for Rx stall during OOM and network stress
net: phy: Fix PHY module checks and NULL deref in phy_attach_direct()
net: thunderx: Fix PHY autoneg for SGMII QLM mode
net: dsa: Do not destroy invalid network devices
ping: fix a null pointer dereference
packet: round up linear to header len
net: introduce device min_header_len
sit: fix a double free on error path
lwtunnel: valid encap attr check should return 0 when lwtunnel is disabled
ipv6: addrconf: fix generation of new temporary addresses
Linus Torvalds [Fri, 10 Feb 2017 22:29:30 +0000 (14:29 -0800)]
Merge tag 'sound-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are some last-minute fixes: two fixes for races in ALSA sequencer
queue spotted by syzkaller, a revert for a regression of LINE6 driver
(since 4.9), and a trivial new codec ID addition for Nvidia HDMI"
* tag 'sound-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - adding a new NV HDMI/DP codec ID in the driver
ALSA: seq: Fix race at creating a queue
Revert "ALSA: line6: Only determine control port properties if needed"
ALSA: seq: Don't handle loop timeout at snd_seq_pool_done()
Linus Torvalds [Fri, 10 Feb 2017 22:23:45 +0000 (14:23 -0800)]
Merge tag 'nfsd-4.10-3' of git://linux-nfs.org/~bfields/linux
Pull nfsd revert from Bruce Fields:
"This patch turned out to have a couple problems. The problems are
fixable, but at least one of the fixes is a little ugly. The original
bug has always been there, so we can wait another week or two to get
this right"
* tag 'nfsd-4.10-3' of git://linux-nfs.org/~bfields/linux:
nfsd: Revert "nfsd: special case truncates some more"
Linus Torvalds [Fri, 10 Feb 2017 22:10:35 +0000 (14:10 -0800)]
Merge tag 'powerpc-4.10-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes friom Michael Ellerman:
"Apologies for the late pull request, but Ben has been busy finding bugs.
- Userspace was semi-randomly segfaulting on radix due to us
incorrectly handling a fault triggered by autonuma, caused by a
patch we merged earlier in v4.10 to prevent the kernel executing
userspace.
- We weren't marking host IPIs properly for KVM in the OPAL ICP
backend.
- The ERAT flushing on radix was missing an isync and was incorrectly
marked as DD1 only.
- The powernv CPU hotplug code was missing a wakeup type and failing
to flush the interrupt correctly when using OPAL ICP
Thanks to Benjamin Herrenschmidt"
* tag 'powerpc-4.10-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/powernv: Properly set "host-ipi" on IPIs
powerpc/powernv: Fix CPU hotplug to handle waking on HVI
powerpc/mm/radix: Update ERAT flushes when invalidating TLB
powerpc/mm: Fix spurrious segfaults on radix with autonuma
Eric Dumazet [Fri, 10 Feb 2017 00:15:52 +0000 (16:15 -0800)]
l2tp: do not use udp_ioctl()
udp_ioctl(), as its name suggests, is used by UDP protocols,
but is also used by L2TP :(
L2TP should use its own handler, because it really does not
look the same.
SIOCINQ for instance should not assume UDP checksum or headers.
Thanks to Andrey and syzkaller team for providing the report
and a nice reproducer.
While crashes only happen on recent kernels (after commit 7c13f97ffde6 ("udp: do fwd memory scheduling on dequeue")), this
probably needs to be backported to older kernels.
Fixes: 7c13f97ffde6 ("udp: do fwd memory scheduling on dequeue") Fixes: 85584672012e ("udp: Fix udp_poll() and ioctl()") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Andrey Konovalov <andreyknvl@google.com> Acked-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Boris Ostrovsky [Mon, 30 Jan 2017 17:45:46 +0000 (12:45 -0500)]
xen-netfront: Delete rx_refill_timer in xennet_disconnect_backend()
rx_refill_timer should be deleted as soon as we disconnect from the
backend since otherwise it is possible for the timer to go off before
we get to xennet_destroy_queues(). If this happens we may dereference
queue->rx.sring which is set to NULL in xennet_disconnect_backend().
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> CC: stable@vger.kernel.org Reviewed-by: Juergen Gross <jgross@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ralf Baechle [Thu, 9 Feb 2017 13:12:11 +0000 (14:12 +0100)]
NET: mkiss: Fix panic
If a USB-to-serial adapter is unplugged, the driver re-initializes, with
dev->hard_header_len and dev->addr_len set to zero, instead of the correct
values. If then a packet is sent through the half-dead interface, the
kernel will panic due to running out of headroom in the skb when pushing
for the AX.25 headers resulting in this panic:
[<c0595468>] (skb_panic) from [<c0401f70>] (skb_push+0x4c/0x50)
[<c0401f70>] (skb_push) from [<bf0bdad4>] (ax25_hard_header+0x34/0xf4 [ax25])
[<bf0bdad4>] (ax25_hard_header [ax25]) from [<bf0d05d4>] (ax_header+0x38/0x40 [mkiss])
[<bf0d05d4>] (ax_header [mkiss]) from [<c041b584>] (neigh_compat_output+0x8c/0xd8)
[<c041b584>] (neigh_compat_output) from [<c043e7a8>] (ip_finish_output+0x2a0/0x914)
[<c043e7a8>] (ip_finish_output) from [<c043f948>] (ip_output+0xd8/0xf0)
[<c043f948>] (ip_output) from [<c043f04c>] (ip_local_out_sk+0x44/0x48)
This patch makes mkiss behave like the 6pack driver. 6pack does not
panic. In 6pack.c sp_setup() (same function name here) the values for
dev->hard_header_len and dev->addr_len are set to the same values as in
my mkiss patch.
[ralf@linux-mips.org: Massages original submission to conform to the usual
standards for patch submissions.]
Signed-off-by: Thomas Osterried <thomas@osterried.de> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Kejian Yan [Thu, 9 Feb 2017 11:46:15 +0000 (11:46 +0000)]
net: hns: Fix the device being used for dma mapping during TX
This patch fixes the device being used to DMA map skb->data.
Erroneous device assignment causes the crash when SMMU is enabled.
This happens during TX since buffer gets DMA mapped with device
correspondign to net_device and gets unmapped using the device
related to DSAF.
Signed-off-by: Kejian Yan <yankejian@huawei.com> Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrey Ryabinin [Fri, 10 Feb 2017 09:54:05 +0000 (12:54 +0300)]
x86/mm/ptdump: Fix soft lockup in page table walker
CONFIG_KASAN=y needs a lot of virtual memory mapped for its shadow.
In that case ptdump_walk_pgd_level_core() takes a lot of time to
walk across all page tables and doing this without
a rescheduling causes soft lockups:
Thomas Gleixner [Thu, 9 Feb 2017 15:08:42 +0000 (16:08 +0100)]
x86/tsc: Make the TSC ADJUST sanitizing work for tsc_reliable
When the TSC is marked reliable then the synchronization check is skipped,
but that also skips the TSC ADJUST sanitizing code. So on a machine with a
wreckaged BIOS the TSC deviation between CPUs might go unnoticed.
Let the TSC adjust sanitizing code run unconditionally and just skip the
expensive synchronization checks when TSC is marked reliable.
Thomas Gleixner [Thu, 9 Feb 2017 15:08:41 +0000 (16:08 +0100)]
x86/tsc: Avoid the large time jump when sanitizing TSC ADJUST
Olof reported that on a machine which has a BIOS wreckaged TSC the
timestamps in dmesg are making a large jump because the TSC value is
jumping forward after resetting the TSC ADJUST register to a sane value.
This can be avoided by calling the TSC ADJUST saniziting function before
initializing the per cpu sched clock machinery. That takes the offset into
account and avoid the time jump.
What cannot be avoided is that the 'Firmware Bug' warnings on the secondary
CPUs are printed with the large time offsets because it would be too much
effort and ugly hackery to print those warnings into a buffer and emit them
after the adjustemt on the starting CPUs. It's a firmware bug and should be
fixed in firmware. The weird timestamps are collateral damage and just
illustrate the sillyness of the BIOS folks:
Reported-by: Olof Johansson <olof@lixom.net> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/20170209151231.411460506@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
tick/nohz: Fix possible missing clock reprog after tick soft restart
ts->next_tick keeps track of the next tick deadline in order to optimize
clock programmation on irq exit and avoid redundant clock device writes.
Now if ts->next_tick missed an update, we may spuriously miss a clock
reprog later as the nohz code is fooled by an obsolete next_tick value.
This is what happens here on a specific path: when we observe an
expired timer from the nohz update code on irq exit, we perform a soft
tick restart which simply fires the closest possible tick without
actually exiting the nohz mode and restoring a periodic state. But we
forget to update ts->next_tick accordingly.
As a result, after the next tick resulting from such soft tick restart,
the nohz code sees a stale value on ts->next_tick which doesn't match
the clock deadline that just expired. If that obsolete ts->next_tick
value happens to collide with the actual next tick deadline to be
scheduled, we may spuriously bypass the clock reprogramming. In the
worst case, the tick may never fire again.
Fix this with a ts->next_tick reset on soft tick restart.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Reviewed: Wanpeng Li <wanpeng.li@hotmail.com> Acked-by: Rik van Riel <riel@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/1486485894-29173-1-git-send-email-fweisbec@gmail.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Peter Zijlstra [Tue, 31 Jan 2017 10:27:10 +0000 (11:27 +0100)]
perf/core: Fix crash in perf_event_read()
Alexei had his box explode because doing read() on a package
(rapl/uncore) event that isn't currently scheduled in ends up doing an
out-of-bounds load.
Rework the code to more explicitly deal with event->oncpu being -1.
J. Bruce Fields [Thu, 9 Feb 2017 19:20:42 +0000 (14:20 -0500)]
nfsd: Revert "nfsd: special case truncates some more"
This patch incorrectly attempted nested mnt_want_write, and incorrectly
disabled nfsd's owner override for truncate. We'll fix those problems
and make another attempt soon, for the moment I think the safest is to
revert.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Linus Torvalds [Fri, 10 Feb 2017 01:46:30 +0000 (17:46 -0800)]
Merge tag 'drm-fixes-for-v4.10-rc8' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"This should be the final set of drm fixes for 4.10: one vmwgfx boot
fix, one vc4 fix, and a few i915 fixes:
* tag 'drm-fixes-for-v4.10-rc8' of git://people.freedesktop.org/~airlied/linux:
drm: vc4: adapt to new behaviour of drm_crtc.c
drm/i915: Always convert incoming exec offsets to non-canonical
drm/i915: Remove overzealous fence warn on runtime suspend
drm/i915/bxt: Add MST support when do DPLL calculation
drm/i915: don't warn about Skylake CPU - KabyPoint PCH combo
drm/i915: fix i915 running as dom0 under Xen
drm/i915: Flush untouched framebuffers before display on !llc
drm/i915: fix use-after-free in page_flip_completed()
drm/vmwgfx: Fix depth input into drm_mode_legacy_fb_format
Steffen Maier [Wed, 8 Feb 2017 14:34:22 +0000 (15:34 +0100)]
scsi: zfcp: fix use-after-free by not tracing WKA port open/close on failed send
Dan Carpenter kindly reported:
<quote>
The patch d27a7cb91960: "zfcp: trace on request for open and close of
WKA port" from Aug 10, 2016, leads to the following static checker
warning:
drivers/s390/scsi/zfcp_fsf.c:1615 zfcp_fsf_open_wka_port()
warn: 'req' was already freed.
1613 out:
1614 spin_unlock_irq(&qdio->req_q_lock);
1615 if (req && !IS_ERR(req))
1616 zfcp_dbf_rec_run_wka("fsowp_1", wka_port, req->req_id);
^^^^^^^^^^^
Use after free.
1617 return retval;
1618 }
Same thing for zfcp_fsf_close_wka_port() as well.
</quote>
Rather than relying on req being NULL (or ERR_PTR) for all cases where
we don't want to trace or should not trace,
simply check retval which is unconditionally initialized with -EIO != 0
and it can only become 0 on successful retval = zfcp_fsf_req_send(req).
With that we can also remove the then again unnecessary unconditional
initialization of req which was introduced with that earlier commit.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Suggested-by: Benjamin Block <bblock@linux.vnet.ibm.com> Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com> Fixes: d27a7cb91960 ("zfcp: trace on request for open and close of WKA port") Cc: <stable@vger.kernel.org> #2.6.38+ Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com> Reviewed-by: Jens Remus <jremus@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Dave Carroll [Thu, 9 Feb 2017 18:04:47 +0000 (11:04 -0700)]
scsi: aacraid: Fix INTx/MSI-x issue with older controllers
commit 78cbccd3bd68 ("aacraid: Fix for KDUMP driver hang")
caused a problem on older controllers which do not support MSI-x (namely
ASR3405,ASR3805). This patch conditionalizes the previous patch to
controllers which support MSI-x
Cc: <stable@vger.kernel.org> # v4.7+ Fixes: 78cbccd3bd68 ("aacraid: Fix for KDUMP driver hang") Reported-by: Arkadiusz Miskiewicz <a.miskiewicz@gmail.com> Signed-off-by: Dave Carroll <david.carroll@microsemi.com> Reviewed-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Dave Airlie [Fri, 10 Feb 2017 00:14:24 +0000 (10:14 +1000)]
Merge tag 'drm-intel-fixes-2017-02-09' of git://anongit.freedesktop.org/git/drm-intel into drm-fixes
Hopefully final fixes for v4.10, about half of them stable material.
* tag 'drm-intel-fixes-2017-02-09' of git://anongit.freedesktop.org/git/drm-intel:
drm/i915: Always convert incoming exec offsets to non-canonical
drm/i915: Remove overzealous fence warn on runtime suspend
drm/i915/bxt: Add MST support when do DPLL calculation
drm/i915: don't warn about Skylake CPU - KabyPoint PCH combo
drm/i915: fix i915 running as dom0 under Xen
drm/i915: Flush untouched framebuffers before display on !llc
drm/i915: fix use-after-free in page_flip_completed()
USB PHYs need the MDIO clock divisor enabled earlier to work.
Initialize mdio clock divisor in probe function. The ext bus
bit available in the same register will be used by mdio mux
to enable external mdio.
Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com> Fixes: ddc24ae1 ("net: phy: Broadcom iProc MDIO bus driver") Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jon Mason <jon.mason@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Wed, 8 Feb 2017 13:16:45 +0000 (21:16 +0800)]
igmp, mld: Fix memory leak in igmpv3/mld_del_delrec()
In function igmpv3/mld_add_delrec() we allocate pmc and put it in
idev->mc_tomb, so we should free it when we don't need it in del_delrec().
But I removed kfree(pmc) incorrectly in latest two patches. Now fix it.
Fixes: 24803f38a5c0 ("igmp: do not remove igmp souce list info when ...") Fixes: 1666d49e1d41 ("mld: do not remove mld souce list info when ...") Reported-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ross Lagerwall [Wed, 8 Feb 2017 10:57:37 +0000 (10:57 +0000)]
xen-netfront: Improve error handling during initialization
This fixes a crash when running out of grant refs when creating many
queues across many netdevs.
* If creating queues fails (i.e. there are no grant refs available),
call xenbus_dev_fatal() to ensure that the xenbus device is set to the
closed state.
* If no queues are created, don't call xennet_disconnect_backend as
netdev->real_num_tx_queues will not have been set correctly.
* If setup_netfront() fails, ensure that all the queues created are
cleaned up, not just those that have been set up.
* If any queues were set up and an error occurs, call
xennet_destroy_queues() to clean up the napi context.
* If any fatal error occurs, unregister and destroy the netdev to avoid
leaving around a half setup network device.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 9 Feb 2017 21:41:43 +0000 (16:41 -0500)]
Merge branch 'sierra_net-fixes'
Stefan Brüns says:
====================
Fixes for sierra_net driver
When trying to initiate a dual-stack (ipv4v6) connection, a MC7710, FW
version SWI9200X_03.05.24.00ap answers with an unsupported LSI. Add support
for this LSI.
Also the link_type should be ignored when going idle, otherwise the modem
is stuck in a bad link state.
Tested on MC7710, T-Mobile DE, APN internet.telekom, IPv4v6 PDP type. Both
IPv4 and IPv6 connections work.
v2: Do not overwrite protocol field in rx_fixup
v3: Remove leftover struct ethhdr *eth declaration
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Brüns [Wed, 8 Feb 2017 01:46:33 +0000 (02:46 +0100)]
sierra_net: Skip validating irrelevant fields for IDLE LSIs
When the context is deactivated, the link_type is set to 0xff, which
triggers a warning message, and results in a wrong link status, as
the LSI is ignored.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Brüns [Wed, 8 Feb 2017 01:46:32 +0000 (02:46 +0100)]
sierra_net: Add support for IPv6 and Dual-Stack Link Sense Indications
If a context is configured as dualstack ("IPv4v6"), the modem indicates
the context activation with a slightly different indication message.
The dual-stack indication omits the link_type (IPv4/v6) and adds
additional address fields.
IPv6 LSIs are identical to IPv4 LSIs, but have a different link type.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de> Reviewed-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
when calling syscall(__NR_write, sock2, 0x208aaf27ul, 0x0ul) on a KCM
seqpacket socket. It appears that kcm_sendmsg() does not handle len==0
case correctly, which causes an empty skb is allocated and queued.
Fix this by skipping the skb allocation for len==0 case.
Reported-by: Dmitry Vyukov <dvyukov@google.com> Cc: Tom Herbert <tom@herbertland.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
xen-netfront: Rework the fix for Rx stall during OOM and network stress
The commit 90c311b0eeea ("xen-netfront: Fix Rx stall during network
stress and OOM") caused the refill timer to be triggerred almost on
all invocations of xennet_alloc_rx_buffers for certain workloads.
This reworks the fix by reverting to the old behaviour and taking into
consideration the skb allocation failure. Refill timer is now triggered
on insufficient requests or skb allocation failure.
Signed-off-by: Vineeth Remanan Pillai <vineethp@amazon.com> Fixes: 90c311b0eeea (xen-netfront: Fix Rx stall during network stress and OOM) Reported-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pull SCSI target fixes from Nicholas Bellinger:
"This target series for v4.10 contains fixes which address a few
long-standing bugs that DATERA's QA + automation teams have uncovered
while putting v4.1.y target code into production usage.
We've been running the top three in our nightly automated regression
runs for the last two months, and the COMPARE_AND_WRITE fix Mr. Gary
Guo has been manually verifying against a four node ESX cluster this
past week.
Note all of them have CC' stable tags.
Summary:
- Fix a bug with ESX EXTENDED_COPY + SAM_STAT_RESERVATION_CONFLICT
status, where target_core_xcopy.c logic was incorrectly returning
SAM_STAT_CHECK_CONDITION for all non SAM_STAT_GOOD cases (Nixon
Vincent)
- Fix a TMR LUN_RESET hung task bug while other in-flight TMRs are
being aborted, before the new one had been dispatched into tmr_wq
(Rob Millner)
- Fix a long standing double free OOPs, where a dynamically generated
'demo-mode' NodeACL has multiple sessions associated with it, and
the /sys/kernel/config/target/$FABRIC/$WWN/ subsequently disables
demo-mode, but never converts the dynamic ACL into a explicit ACL
(Rob Millner)
- Fix a long standing reference leak with ESX VAAI COMPARE_AND_WRITE
when the second phase WRITE COMMIT command fails, resulting in
CHECK_CONDITION response never being sent and se_cmd->cmd_kref
never reaching zero (Gary Guo)
Beyond these items on v4.1.y we've reproduced, fixed, and run through
our regression test suite using iscsi-target exports, there are two
additional outstanding list items:
- Remove a >= v4.2 RCU conversion BUG_ON that would trigger when
dynamic node NodeACLs where being converted to explicit NodeACLs.
The patch drops the BUG_ON to follow how pre RCU conversion worked
for this special case (Benjamin Estrabaud)
- Add ibmvscsis target_core_fabric_ops->max_data_sg_nent assignment
to match what IBM's Virtual SCSI hypervisor is already enforcing at
transport layer. (Bryant Ly + Steven Royer)"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
ibmvscsis: Add SGL limit
target: Fix COMPARE_AND_WRITE ref leak for non GOOD status
target: Fix multi-session dynamic se_node_acl double free OOPs
target: Fix early transport_generic_handle_tmr abort scenario
target: Use correct SCSI status during EXTENDED_COPY exception
target: Don't BUG_ON during NodeACL dynamic -> explicit conversion
net: phy: Fix PHY module checks and NULL deref in phy_attach_direct()
The Generic PHY drivers gets assigned after we checked that the current
PHY driver is NULL, so we need to check a few things before we can
safely dereference d->driver. This would be causing a NULL deference to
occur when a system binds to the Generic PHY driver. Update
phy_attach_direct() to do the following:
- grab the driver module reference after we have assigned the Generic
PHY drivers accordingly, and remember we came from the generic PHY
path
- update the error path to clean up the module reference in case the
Generic PHY probe function fails
- split the error path involving phy_detacht() to avoid double free/put
since phy_detach() does all the clean up
- finally, have phy_detach() drop the module reference count before we
call device_release_driver() for the Generic PHY driver case
Fixes: cafe8df8b9bc ("net: phy: Fix lack of reference count on PHY driver") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 9 Feb 2017 19:58:05 +0000 (11:58 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"A fix for a crash in uinput, and a fix for build errors when HID-RMI
is built-in but SERIO is a module"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics-rmi4 - select 'SERIO' when needed
Input: uinput - fix crash when mixing old and new init style
Brian Norris [Thu, 9 Feb 2017 06:44:44 +0000 (22:44 -0800)]
pstore: don't OOPS when there are no ftrace zones
We'll OOPS in ramoops_get_next_prz() if the platform didn't ask for any
ftrace zones (i.e., cxt->fprzs will be NULL). Let's just skip this
entire FTRACE section if there's no 'fprzs'.
Regression seen on a coreboot/depthcharge-based Chromebook.
Fixes: 2fbea82bbb89 ("pstore: Merge per-CPU ftrace records into one") Cc: Joel Fernandes <joelaf@google.com> Cc: Kees Cook <keescook@chromium.org> Signed-off-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kees Cook <keescook@chromium.org>
powerpc/powernv: Fix CPU hotplug to handle waking on HVI
The IPIs come in as HVI not EE, so we need to test the appropriate
SRR1 bits. The encoding is such that it won't have false positives
on P7 and P8 so we can just test it like that. We also need to handle
the icp-opal variant of the flush.
Fixes: d74361881f0d ("powerpc/xics: Add ICP OPAL backend") Cc: stable@vger.kernel.org # v4.8+ Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/mm/radix: Update ERAT flushes when invalidating TLB
Three tiny changes to the ERAT flushing logic: First don't make
it depend on DD1. It hasn't been decided yet but we might run
DD2 in a mode that also requires explicit flushes for performance
reasons so make it unconditional. We also add a missing isync, and
finally remove the flush from _tlbiel_va as it is only necessary
for congruence-class invalidations (PID, LPID and full TLB), not
targetted invalidations.
Fixes: 96ed1fe511a8 ("powerpc/mm/radix: Invalidate ERAT on tlbiel for POWER9 DD1") Cc: stable@vger.kernel.org # v4.9+ Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Gabriel C reports that it causes his machine to not boot, and we haven't
tracked down the reason for it yet. Since the bug it fixes has been
around for a longish time, we're better off reverting the fix for now.
Gabriel says:
"It hangs early and freezes with a lot RCU warnings.
The box is a PRIMERGY TX200 S5 , 2 socket , 2 x E5520 CPU(s) installed"
and Ruslan and Thomas are currently stumped.
Reported-and-bisected-by: Gabriel C <nix.or.die@gmail.com> Cc: Ruslan Ruslichenko <rruslich@cisco.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: stable@kernel.org # for the backport of the original commit Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / mirror_ubuntu-kernels.git / log