This patch explicitly defines the CSUM offload engine type which need
(not mandatory) to be passed from the platform code.
STMMAC core supports two check sum offload engine types- Type-1 & Type-2.
Also, there are STMMAC cores that do not have the check sum offload
capabilities.
The behaviour of Type-1 & Type-2 cores related to provision of checksum
increases the packet length for Type-1 cores by 2, as the checksum is appended
at the end of data packet and the same is made accountable in the DMA status.
The STMMAC cores beyond Version-3.5 provide HW interface registers which allows
the user to read the HW capabilities, while to support the previous cores the
information related to HW capabilities has to be provided from the platform
code.
The Type-1 cores which do not have the HW register interface need this
information.
This patch also updates the driver's doc.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com> Hacked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac: Allow stmmac to work with other PHY buses(v3).
As stmmac mdio bus name prefix is hardcoded in the driver, this allows
only phys on stmmac mdio buses to connect, however stmmac should allow
phys on other mdio buses too.
This patch adds new variable phy_bus_name to plat_stmmacenet_data
struct to let the BSP decide which phy bus to be used by stmmac driver.
A typical use-case is to have generic MDIO buses like mdio-gpio on top
of stmmac.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com> Acked-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Renamed following functions:
bnad_cleanup_tx to bnad_destroy_tx
bnad_free_all_txbufs to bnad_txq_cleanup
bnad_free_txbufs to bnad_txcmpl_process
bnad_tx to bnad_tx_complete
bnad_cleanup_rx to bnad_destroy_rx
bnad_reset_rcb to bnad_rcb_cleanup
bnad_free_all_rxbufs to bnad_rxq_cleanup
bnad_cq_cmpl_init to bnad_cq_cleanup
bnad_alloc_n_post_rxbufs to bnad_rxq_post
bnad_poll_cq to bnad_cq_process
Signed-off-by: Jing Huang <huangj@brocade.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The scheduling of tasklet and keeping the interrupts enabled makes interrupt
reduntant. 20% of the Tx interrupts have nothing left to process or could not
process as Tx tasklet was running.
Signed-off-by: Jing Huang <huangj@brocade.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes busy wait in tx/rx cleanup. bnad_cb_tx_cleanup() and
bnad_cb_rx_cleanup() functions are called from irq context, and currently
they do busy wait for the in-flight transmit or the currently executing napi
polling routine to complete. To fix the issue, we create a workqueue to defer
tx & rx cleanup processing, an in the tx rx cleanup handler, we will
wait respective in flight processing to complete, before freeing the buffers.
Signed-off-by: Jing Huang <huangj@brocade.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Added NFC pause/resume logic. We only do NFC pause/resume if NFC version
is greater than 0x143 and it was halted before, otherwise we revert to
old NFC halt mechanism.
Made changes to avoid clearing off the interrupts during the initial
pll initialization.
Signed-off-by: Jing Huang <huangj@brocade.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bna: Serialize smem access during adapter initialization
Use init semaphore to serialize execution of the "unlock IOC semaphore"
code. Added bfa_ioc_fwver_clear() function to clear the firmware header if
last firmwar boot is not from driver.
Signed-off-by: Jing Huang <huangj@brocade.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rob Herring [Tue, 3 Apr 2012 15:34:00 +0000 (15:34 +0000)]
net: remove ixp2000 ethernet driver
The platform is removed, so there are no users of this driver.
Signed-off-by: Rob Herring <rob.herring@calxeda.com> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: Jesse Brandeburg <jesse.brandeburg@intel.com> Cc: Bruce Allan <bruce.w.allan@intel.com> Cc: Carolyn Wyborny <carolyn.wyborny@intel.com> Cc: Don Skidmore <donald.c.skidmore@intel.com> Cc: Greg Rose <gregory.v.rose@intel.com> Cc: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Cc: Alex Duyck <alexander.h.duyck@intel.com> Cc: John Ronciak <john.ronciak@intel.com> Cc: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
Richard Cochran [Tue, 3 Apr 2012 22:59:22 +0000 (22:59 +0000)]
ethtool: Add a common function for drivers with transmit time stamping.
Currently, most drivers do not support transmit SO_TIMESTAMPING. For those
that do support it, there is one appropriate response to the get_ts_info
query. This patch adds a common function providing this response.
Signed-off-by: Richard Cochran <richardcochran@gmail.com> Reviewed-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Richard Cochran [Tue, 3 Apr 2012 22:59:17 +0000 (22:59 +0000)]
ethtool: Introduce a method for getting time stamping capabilities.
This commit adds a new ethtool ioctl that exposes the SO_TIMESTAMPING
capabilities of a network interface. In addition, user space programs
can use this ioctl to discover the PTP Hardware Clock (PHC) device
associated with the interface.
Since software receive time stamps are handled by the stack, the generic
ethtool code can answer the query correctly in case the MAC or PHY
drivers lack special time stamping features.
Signed-off-by: Richard Cochran <richardcochran@gmail.com> Reviewed-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6: Fix 'inet6_rtm_getroute' to release 'rt->dst' in case of 'alloc_skb' failure
In 72331bc [ipv6: Fix RTM_GETROUTE's interpretation of RTA_IIF to be
consistent with ipv4] the code of 'inet6_rtm_getroute()' was re-ordered
such that the reference to 'rt->dst' is incremented prior skb
allocation.
Hence, if 'alloc_skb()' fails, must drop a reference from 'rt->dst'.
Add the missing 'dst_release()' call.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Richard Cochran [Fri, 16 Mar 2012 10:55:37 +0000 (10:55 +0000)]
igb: offer a PTP Hardware Clock instead of the timecompare method
This commit removes the legacy timecompare code from the igb driver and
offers a tunable PHC instead.
Signed-off-by: Richard Cochran <richardcochran@gmail.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Richard Cochran [Fri, 16 Mar 2012 10:55:32 +0000 (10:55 +0000)]
igb: add PTP Hardware Clock code
This patch adds a source file implementing a PHC. Only the basic
clock operations have been implemented, although the hardware
would offer some ancillary functions. The code is fairly self
contained and is not yet used in the main igb driver.
Every timestamp and clock read operation must consult the overflow
counter to form a correct time value. Access to the counter is
protected by a spin lock, and the counter is implemented using the
standard cyclecounter/timecounter code.
Signed-off-by: Richard Cochran <richardcochran@gmail.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Emil Tantilov [Thu, 22 Mar 2012 03:00:29 +0000 (03:00 +0000)]
ixgbe: consolidate reporting of MSIX vectors into a single function
This patch modifies ixgbe_get_pcie_msix_count_generic() to support
all current HW and removes the 82598 specific function.
- change the type of ixgbe_get_pcie_msix_count_generic() to u16
- include a check to make sure the maximum allowed number of vectors
is not exceeded.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Tue, 20 Mar 2012 03:48:29 +0000 (03:48 +0000)]
e1000e: update driver version number
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Tue, 20 Mar 2012 03:48:13 +0000 (03:48 +0000)]
e1000e: cleanup indexed register arrays
Some Rx and Tx specific registers are arrays indexed by the queue number.
For clarity, specify the intended queue rather than obscuring it behind a
define.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Tue, 20 Mar 2012 03:48:19 +0000 (03:48 +0000)]
e1000e: cleanup NAPI routine
Rename NAPI polling routine and a parameter with more appropriate names,
refactor a conditional branch to get rid of an unnecessary goto/label and
fix a line exceeding 80 columns.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Matthew Vick [Fri, 16 Mar 2012 09:03:01 +0000 (09:03 +0000)]
e1000e: Minor comment clean-up.
Move the first phrase of a multi-line comment to the second line.
Signed-off-by: Matthew Vick <matthew.vick@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ben Greear [Wed, 4 Apr 2012 06:01:29 +0000 (06:01 +0000)]
e1000: Support RX-ALL flag.
This allows the NIC to receive errored frames (bad FCS, etc)
and pass them up the stack. This can be useful when using
sniffers.
Signed-off-by: Ben Greear <greearb@candelatech.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The congestion management code has migrated into a common location,
allowing all fw writes controlling mf congestion to be made in a
single function in the code. This is a semantic change.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Restore remote-faule detection, which periodically checks for
remote-fault on the MAC layer. In case physical link appear to be
up but fault is set, it will provide a link down indication, and
when the fault is cleared, it will indicate link up again.
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com> Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x: added support for working with one msix irq.
Until now, the bnx2x driver needed at least 2 available msix interrupt
vectors in order to use msix. This patch add the possibility of configuring
msix when only one interrupt vector is available.
Notice this patch contains lines with over 80 characters, as it keeps print
strings in a single line.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
During boot-from-SAN, if msix interrupts are unavailable and inta
is requested, it is possible that inta would be disabled in the
pci bus. This patch enables inta when requested.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Removed uninformative debug prints, as well as two functions
which were hardly used in the code.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Akinobu Mita [Mon, 2 Apr 2012 22:47:16 +0000 (22:47 +0000)]
ppp: use for_each_set_bit_from
Use for_each_set_bit_from to iterate over all the set bit in a memory
region.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: Dmitry Kozlov <xeb@mail.ru> Cc: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
Haiyang Zhang [Tue, 27 Mar 2012 13:20:45 +0000 (13:20 +0000)]
net/hyperv: Add flow control based on hi/low watermark
In the existing code, we only stop queue when the ringbuffer is full,
so the current packet has to be dropped or retried from upper layer.
This patch stops the tx queue when available ringbuffer is below
the low watermark. So the ringbuffer still has small amount of space
available for the current packet. This will reduce the overhead of
retries on sending.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Reviewed-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Lino Sanfilippo [Fri, 30 Mar 2012 07:36:16 +0000 (07:36 +0000)]
sky2: fix missing register reset on error path in sky2_test_msi()
In sky2_test_msi() the temporarily set SW IRQ in B0 register is not reset in case
that request_irq() fails.
With this patch we only set the interrupt mask if request_irq() was successful.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 3 Apr 2012 05:28:28 +0000 (05:28 +0000)]
af_unix: reduce high order page allocations
unix_dgram_sendmsg() currently builds linear skbs, and this can stress
page allocator with high order page allocations. When memory gets
fragmented, this can eventually fail.
We can try to use order-2 allocations for skb head (SKB_MAX_ALLOC) plus
up to 16 page fragments to lower pressure on buddy allocator.
This patch has no effect on messages of less than 16064 bytes.
(on 64bit arches with PAGE_SIZE=4096)
For bigger messages (from 16065 to 81600 bytes), this patch brings
reliability at the expense of performance penalty because of extra pages
allocations.
Ben Greear [Thu, 29 Mar 2012 12:51:30 +0000 (12:51 +0000)]
net: Report dev->promiscuity in netlink reports.
The standard ways of probing a device's promiscuity
(ifi_flags, for instance) does not report the actual
state of the device. This patch adds dev->promiscuity
to the netlink netdevice report so that users can know
for certain if the device is acting PROMISC or not.
Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/ipv6/addrconf.c:340: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
net/ipv6/addrconf.c:342: ERROR: "foo * bar" should be "foo *bar"
net/ipv6/addrconf.c:444: ERROR: "foo * bar" should be "foo *bar"
net/ipv6/addrconf.c:1337: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
net/ipv6/addrconf.c:1526: ERROR: "(foo*)" should be "(foo *)"
net/ipv6/addrconf.c:1671: ERROR: open brace '{' following function declarations go on the next line
net/ipv6/addrconf.c:1914: ERROR: "foo * bar" should be "foo *bar"
net/ipv6/addrconf.c:2368: ERROR: "foo * bar" should be "foo *bar"
net/ipv6/addrconf.c:2370: ERROR: "foo * bar" should be "foo *bar"
net/ipv6/addrconf.c:2416: ERROR: "foo * bar" should be "foo *bar"
net/ipv6/addrconf.c:2437: ERROR: "foo * bar" should be "foo *bar"
net/ipv6/addrconf.c:2573: ERROR: "foo * bar" should be "foo *bar"
net/ipv6/addrconf.c:3797: ERROR: "foo* bar" should be "foo *bar"
Signed-off-by: Eldad Zack <eldad@fogrefinery.com> Signed-off-by: David S. Miller <davem@davemloft.net>
icmp.c:501: ERROR: "(foo*)" should be "(foo *)"
icmp.c:582: ERROR: "(foo*)" should be "(foo *)"
icmp.c:954: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
Signed-off-by: Eldad Zack <eldad@fogrefinery.com> Signed-off-by: David S. Miller <davem@davemloft.net>
exthdrs_core.c:113: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
exthdrs_core.c:114: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
Signed-off-by: Eldad Zack <eldad@fogrefinery.com> Signed-off-by: David S. Miller <davem@davemloft.net>
exthdrs.c:726: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
exthdrs.c:741: ERROR: "(foo*)" should be "(foo *)"
exthdrs.c:741: ERROR: "(foo*)" should be "(foo *)"
exthdrs.c:744: ERROR: "(foo**)" should be "(foo **)"
exthdrs.c:746: ERROR: "(foo**)" should be "(foo **)"
exthdrs.c:748: ERROR: "(foo**)" should be "(foo **)"
exthdrs.c:750: ERROR: "(foo**)" should be "(foo **)"
exthdrs.c:755: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
exthdrs.c:896: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
Signed-off-by: Eldad Zack <eldad@fogrefinery.com> Signed-off-by: David S. Miller <davem@davemloft.net>
datagram.c:101: ERROR: "(foo*)" should be "(foo *)"
datagram.c:521: ERROR: space required before the open parenthesis '('
datagram.c:830: WARNING: braces {} are not necessary for single statement blocks
datagram.c:849: WARNING: braces {} are not necessary for single statement blocks
Signed-off-by: Eldad Zack <eldad@fogrefinery.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-kernels.git / log