The MIPS GIC contains a block of registers used to map local interrupts
to a particular CPU interrupt pin. Since these registers are found at a
consecutive range of addresses we access them using an index, via the
(read|write)_gic_v[lo]_map accessor functions. We currently use values
from enum mips_gic_local_interrupt as those indices.
Unfortunately whilst enum mips_gic_local_interrupt provides the correct
offsets for bits in the pending & mask registers, the ordering of the
map registers is subtly different... Compared with the ordering of
pending & mask bits, the map registers move the FDC from the end of the
list to index 3 after the timer interrupt. As a result the performance
counter & software interrupts are therefore at indices 4-6 rather than
indices 3-5.
Notably this causes problems with performance counter interrupts being
incorrectly mapped on some systems, and presumably will also cause
problems for FDC interrupts.
Introduce a function to map from enum mips_gic_local_interrupt to the
index of the corresponding map register, and use it to ensure we access
the map registers for the correct interrupts.
Signed-off-by: Paul Burton <paul.burton@mips.com> Fixes: a0dc5cb5e31b ("irqchip: mips-gic: Simplify gic_local_irq_domain_map()") Fixes: da61fcf9d62a ("irqchip: mips-gic: Use irq_cpu_online to (un)mask all-VP(E) IRQs") Reported-and-tested-by: Archer Yan <ayan@wavecomp.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Jason Cooper <jason@lakedaemon.net> Cc: stable@vger.kernel.org # v4.14+ Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
ld.lld: error: undefined symbol: __efistub___stack_chk_guard
>>> referenced by arm-stub.c:73
(/home/nathan/cbl/linux/drivers/firmware/efi/libstub/arm-stub.c:73)
>>> arm-stub.stub.o:(__efistub_install_memreserve_table)
in archive ./drivers/firmware/efi/libstub/lib.a
These failures come from the lack of -fno-stack-protector, which is
added via cc-option in drivers/firmware/efi/libstub/Makefile. When an
unknown flag is added to KBUILD_CFLAGS, clang will noisily warn that it
is ignoring the option like above, unlike gcc, who will just error.
$ gcc -Wsometimes-uninitialized tmp.c; echo $?
gcc: error: unrecognized command line option
‘-Wsometimes-uninitialized’; did you mean ‘-Wmaybe-uninitialized’?
1
For cc-option to work properly with clang and behave like gcc, -Werror
is needed, which was done in commit c3f0d0bc5b01 ("kbuild, LLVMLinux:
Add -Werror to cc-option to support clang").
As a consequence of this, when an unknown flag is unconditionally added
to KBUILD_CFLAGS, it will cause cc-option to always fail and those flags
will never get added:
This can be seen when compiling the whole kernel as some warnings that
are normally disabled (see below) show up. The full list of flags
missing from drivers/firmware/efi/libstub are the following (gathered
from diffing .arm64-stub.o.cmd):
GCC 8.1.0 reports that the ldadd instruction encoding, recently added to
insn.c, doesn't match the mask and couldn't possibly be identified:
linux/arch/arm64/include/asm/insn.h: In function 'aarch64_insn_is_ldadd':
linux/arch/arm64/include/asm/insn.h:280:257: warning: bitwise comparison always evaluates to false [-Wtautological-compare]
Bits [31:30] normally encode the size of the instruction (1 to 8 bytes)
and the current instruction value only encodes the 4- and 8-byte
variants. At the moment only the BPF JIT needs this instruction, and
doesn't require the 1- and 2-byte variants, but to be consistent with
our other ldr and str instruction encodings, clear the size field in the
insn value.
Fixes: 34b8ab091f9ef57a ("bpf, arm64: use more scalable stadd over ldxr / stxr loop in xadd") Acked-by: Daniel Borkmann <daniel@iogearbox.net> Reported-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
udp_tunnel(6)_xmit_skb() called by tipc_udp_xmit() expects a tunnel device
to count packets on dev->tstats, a perpcu variable. However, TIPC is using
udp tunnel with no tunnel device, and pass the lower dev, like veth device
that only initializes dev->lstats(a perpcu variable) when creating it.
Later iptunnel_xmit_stats() called by ip(6)tunnel_xmit() thinks the dev as
a tunnel device, and uses dev->tstats instead of dev->lstats. tstats' each
pointer points to a bigger struct than lstats, so when tstats->tx_bytes is
increased, other percpu variable's members could be overwritten.
syzbot has reported quite a few crashes due to fib_nh_common percpu member
'nhc_pcpu_rth_output' overwritten, call traces are like:
kasan: GPF could be caused by NULL-ptr deref or user memory access
RIP: 0010:dst_dev_put+0x24/0x290 net/core/dst.c:168
<IRQ>
rt_fibinfo_free_cpus net/ipv4/fib_semantics.c:200 [inline]
free_fib_info_rcu+0x2e1/0x490 net/ipv4/fib_semantics.c:217
__rcu_reclaim kernel/rcu/rcu.h:240 [inline]
rcu_do_batch kernel/rcu/tree.c:2437 [inline]
invoke_rcu_callbacks kernel/rcu/tree.c:2716 [inline]
rcu_process_callbacks+0x100a/0x1ac0 kernel/rcu/tree.c:2697
...
The issue exists since tunnel stats update is moved to iptunnel_xmit by
Commit 039f50629b7f ("ip_tunnel: Move stats update to iptunnel_xmit()"),
and here to fix it by passing a NULL tunnel dev to udp_tunnel(6)_xmit_skb
so that the packets counting won't happen on dev->tstats.
Reported-by: syzbot+9d4c12bfd45a58738d0a@syzkaller.appspotmail.com Reported-by: syzbot+a9e23ea2aa21044c2798@syzkaller.appspotmail.com Reported-by: syzbot+c4c4b2bb358bb936ad7e@syzkaller.appspotmail.com Reported-by: syzbot+0290d2290a607e035ba1@syzkaller.appspotmail.com Reported-by: syzbot+a43d8d4e7e8a7a9e149e@syzkaller.appspotmail.com Reported-by: syzbot+a47c5f4c6c00fc1ed16e@syzkaller.appspotmail.com Fixes: 039f50629b7f ("ip_tunnel: Move stats update to iptunnel_xmit()") Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The architecture implementations of 'arch_futex_atomic_op_inuser()' and
'futex_atomic_cmpxchg_inatomic()' are permitted to return only -EFAULT,
-EAGAIN or -ENOSYS in the case of failure.
Update the comments in the asm-generic/ implementation and also a stray
reference in the robust futex documentation.
Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Since ARMv8.1 supplement introduced LSE atomic instructions back in 2016,
lets add support for STADD and use that in favor of LDXR / STXR loop for
the XADD mapping if available. STADD is encoded as an alias for LDADD with
XZR as the destination register, therefore add LDADD to the instruction
encoder along with STADD as special case and use it in the JIT for CPUs
that advertise LSE atomics in CPUID register. If immediate offset in the
BPF XADD insn is 0, then use dst register directly instead of temporary
one.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Returning an error code from futex_atomic_cmpxchg_inatomic() indicates
that the caller should not make any use of *uval, and should instead act
upon on the value of the error code. Although this is implemented
correctly in our futex code, we needlessly copy uninitialised stack to
*uval in the error case, which can easily be avoided.
Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
__udp6_lib_err() may be called when handling icmpv6 message. For example,
the icmpv6 toobig(type=2). __udp6_lib_lookup() is then called
which may call reuseport_select_sock(). reuseport_select_sock() will
call into a bpf_prog (if there is one).
reuseport_select_sock() is expecting the skb->data pointing to the
transport header (udphdr in this case). For example, run_bpf_filter()
is pulling the transport header.
However, in the __udp6_lib_err() path, the skb->data is pointing to the
ipv6hdr instead of the udphdr.
One option is to pull and push the ipv6hdr in __udp6_lib_err().
Instead of doing this, this patch follows how the original
commit 538950a1b752 ("soreuseport: setsockopt SO_ATTACH_REUSEPORT_[CE]BPF")
was done in IPv4, which has passed a NULL skb pointer to
reuseport_select_sock().
Fixes: 538950a1b752 ("soreuseport: setsockopt SO_ATTACH_REUSEPORT_[CE]BPF") Cc: Craig Gallek <kraig@google.com> Signed-off-by: Martin KaFai Lau <kafai@fb.com> Acked-by: Song Liu <songliubraving@fb.com> Acked-by: Craig Gallek <kraig@google.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When the commit a6024562ffd7 ("udp: Add GRO functions to UDP socket")
added udp[46]_lib_lookup_skb to the udp_gro code path, it broke
the reuseport_select_sock() assumption that skb->data is pointing
to the transport header.
This patch follows an earlier __udp6_lib_err() fix by
passing a NULL skb to avoid calling the reuseport's bpf_prog.
Fixes: a6024562ffd7 ("udp: Add GRO functions to UDP socket") Cc: Tom Herbert <tom@herbertland.com> Signed-off-by: Martin KaFai Lau <kafai@fb.com> Acked-by: Song Liu <songliubraving@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We build vlan on top of bonding interface, which vlan offload
is off, bond mode is 802.3ad (LACP) and xmit_hash_policy is
BOND_XMIT_POLICY_ENCAP34.
Because vlan tx offload is off, vlan tci is cleared and skb push
the vlan header in validate_xmit_vlan() while sending from vlan
devices. Then in bond_xmit_hash, __skb_flow_dissect() fails to
get information from protocol headers encapsulated within vlan,
because 'nhoff' is points to IP header, so bond hashing is based
on layer 2 info, which fails to distribute packets across slaves.
This patch always enable bonding's vlan tx offload, pass the vlan
packets to the slave devices with vlan tci, let them to handle
vlan implementation.
Fixes: 278339a42a1b ("bonding: propogate vlan_features to bonding master") Suggested-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: YueHaibing <yuehaibing@huawei.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Currently after setting tap0 link up, the tun code wakes tx/rx waited
queues up in tun_net_open() when .ndo_open() is called, however the
IFF_UP flag has not been set yet. If there's already a wait queue, it
would fail to transmit when checking the IFF_UP flag in tun_sendmsg().
Then the saving vhost_poll_start() will add the wq into wqh until it
is waken up again. Although this works when IFF_UP flag has been set
when tun_chr_poll detects; this is not true if IFF_UP flag has not
been set at that time. Sadly the latter case is a fatal error, as
the wq will never be waken up in future unless later manually
setting link up on purpose.
Fix this by moving the wakeup process into the NETDEV_UP event
notifying process, this makes sure IFF_UP has been set before all
waited queues been waken up.
Signed-off-by: Fei Li <lifei.shirley@bytedance.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
TLV_GET_DATA_LEN() may return a negtive int value, which will be
used as size_t (becoming a big unsigned long) passed into memchr,
cause this issue.
Similar to what it does in tipc_nl_compat_bearer_enable(), this
fix is to return -EINVAL when TLV_GET_DATA_LEN() is negtive in
tipc_nl_compat_bearer_disable(), as well as in
tipc_nl_compat_link_stat_dump() and tipc_nl_compat_link_reset_stats().
v1->v2:
- add the missing Fixes tags per Eric's request.
Fixes: 0762216c0ad2 ("tipc: fix uninit-value in tipc_nl_compat_bearer_enable") Fixes: 8b66fee7f8ee ("tipc: fix uninit-value in tipc_nl_compat_link_reset_stats") Reported-by: syzbot+30eaa8bf392f7fafffaf@syzkaller.appspotmail.com Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This patch is to fix a dst defcnt leak, which can be reproduced by doing:
# ip net a c; ip net a s; modprobe tipc
# ip net e s ip l a n eth1 type veth peer n eth1 netns c
# ip net e c ip l s lo up; ip net e c ip l s eth1 up
# ip net e s ip l s lo up; ip net e s ip l s eth1 up
# ip net e c ip a a 1.1.1.2/8 dev eth1
# ip net e s ip a a 1.1.1.1/8 dev eth1
# ip net e c tipc b e m udp n u1 localip 1.1.1.2
# ip net e s tipc b e m udp n u1 localip 1.1.1.1
# ip net d c; ip net d s; rmmod tipc
and it will get stuck and keep logging the error:
unregister_netdevice: waiting for lo to become free. Usage count = 1
The cause is that a dst is held by the udp sock's sk_rx_dst set on udp rx
path with udp_early_demux == 1, and this dst (eventually holding lo dev)
can't be released as bearer's removal in tipc pernet .exit happens after
lo dev's removal, default_device pernet .exit.
"There are two distinct types of pernet_operations recognized: subsys and
device. At creation all subsys init functions are called before device
init functions, and at destruction all device exit functions are called
before subsys exit function."
So by calling register_pernet_device instead to register tipc_net_ops, the
pernet .exit() will be invoked earlier than loopback dev's removal when a
netns is being destroyed, as fou/gue does.
Note that vxlan and geneve udp tunnels don't have this issue, as the udp
sock is released in their device ndo_stop().
This fix is also necessary for tipc dst_cache, which will hold dsts on tx
path and I will introduce in my next patch.
Reported-by: Li Shuang <shuali@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Now in sctp_endpoint_init(), it holds the sk then creates auth
shkey. But when the creation fails, it doesn't release the sk,
which causes a sk defcnf leak,
Here to fix it by only holding the sk when auth shkey is created
successfully.
Fixes: a29a5bd4f5c3 ("[SCTP]: Implement SCTP-AUTH initializations.") Reported-by: syzbot+afabda3890cc2f765041@syzkaller.appspotmail.com Reported-by: syzbot+276ca1c77a19977c0130@syzkaller.appspotmail.com Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Neil Horman <nhorman@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When ADDSUB bit is set, the system time seconds field is calculated as
the complement of the seconds part of the update value.
For example, if 3.000000001 seconds need to be subtracted from the
system time, this field is calculated as
2^32 - 3 = 4294967296 - 3 = 0x100000000 - 3 = 0xFFFFFFFD
Previously, the 0x100000000 is mistakenly written as 100000000.
This is further simplified from
sec = (0x100000000ULL - sec);
to
sec = -sec;
Fixes: ba1ffd74df74 ("stmmac: fix PTP support for GMAC4") Signed-off-by: Roland Hii <roland.king.guan.hii@intel.com> Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Signed-off-by: Voon Weifeng <weifeng.voon@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In sock_getsockopt(), 'optlen' is fetched the first time from userspace.
'len < 0' is then checked. Then in condition 'SO_MEMINFO', 'optlen' is
fetched the second time from userspace.
If change it between two fetches may cause security problems or unexpected
behaivor, and there is no reason to fetch it a second time.
To fix this, we need to remove the second fetch.
Signed-off-by: JingYi Hou <houjingyi647@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
syzbot found we can leak memory in packet_set_ring(), if user application
provides buggy parameters.
Fixes: 7f953ab2ba46 ("af_packet: TX_RING support for TPACKET_V3") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Sowmini Varadhan <sowmini.varadhan@oracle.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In commit 19e4e768064a8 ("ipv4: Fix raw socket lookup for local
traffic"), the dif argument to __raw_v4_lookup() is coming from the
returned value of inet_iif() but the change was done only for the first
lookup. Subsequent lookups in the while loop still use skb->dev->ifIndex.
Fixes: 19e4e768064a8 ("ipv4: Fix raw socket lookup for local traffic") Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When an application is run that:
a) Sets its scheduler to be SCHED_FIFO
and
b) Opens a memory mapped AF_PACKET socket, and sends frames with the
MSG_DONTWAIT flag cleared, its possible for the application to hang
forever in the kernel. This occurs because when waiting, the code in
tpacket_snd calls schedule, which under normal circumstances allows
other tasks to run, including ksoftirqd, which in some cases is
responsible for freeing the transmitted skb (which in AF_PACKET calls a
destructor that flips the status bit of the transmitted frame back to
available, allowing the transmitting task to complete).
However, when the calling application is SCHED_FIFO, its priority is
such that the schedule call immediately places the task back on the cpu,
preventing ksoftirqd from freeing the skb, which in turn prevents the
transmitting task from detecting that the transmission is complete.
We can fix this by converting the schedule call to a completion
mechanism. By using a completion queue, we force the calling task, when
it detects there are no more frames to send, to schedule itself off the
cpu until such time as the last transmitted skb is freed, allowing
forward progress to be made.
Tested by myself and the reporter, with good results
Change Notes:
V1->V2:
Enhance the sleep logic to support being interruptible and
allowing for honoring to SK_SNDTIMEO (Willem de Bruijn)
V2->V3:
Rearrage the point at which we wait for the completion queue, to
avoid needing to check for ph/skb being null at the end of the loop.
Also move the complete call to the skb destructor to avoid needing to
modify __packet_set_status. Also gate calling complete on
packet_read_pending returning zero to avoid multiple calls to complete.
(Willem de Bruijn)
Move timeo computation within loop, to re-fetch the socket
timeout since we also use the timeo variable to record the return code
from the wait_for_complete call (Neil Horman)
V3->V4:
Willem has requested that the control flow be restored to the
previous state. Doing so lets us eliminate the need for the
po->wait_on_complete flag variable, and lets us get rid of the
packet_next_frame function, but introduces another complexity.
Specifically, but using the packet pending count, we can, if an
applications calls sendmsg multiple times with MSG_DONTWAIT set, each
set of transmitted frames, when complete, will cause
tpacket_destruct_skb to issue a complete call, for which there will
never be a wait_on_completion call. This imbalance will lead to any
future call to wait_for_completion here to return early, when the frames
they sent may not have completed. To correct this, we need to re-init
the completion queue on every call to tpacket_snd before we enter the
loop so as to ensure we wait properly for the frames we send in this
iteration.
Change the timeout and interrupted gotos to out_put rather than
out_status so that we don't try to free a non-existant skb
Clean up some extra newlines (Willem de Bruijn)
Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Reported-by: Matteo Croce <mcroce@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Within at24_loop_until_timeout the timestamp used for timeout checking
is recorded after the I2C transfer and sleep_range(). Under high CPU
load either the execution time for I2C transfer or sleep_range() could
actually be larger than the timeout value. Worst case the I2C transfer
is only tried once because the loop will exit due to the timeout
although the EEPROM is now ready.
To fix this issue the timestamp is recorded at the beginning of each
iteration. That is, before I2C transfer and sleep. Then the timeout
is actually checked against the timestamp of the previous iteration.
This makes sure that even if the timeout is reached, there is still one
more chance to try the I2C transfer in case the EEPROM is ready.
Example:
If you have a system which combines high CPU load with repeated EEPROM
writes you will run into the following scenario.
- System makes a successful regmap_bulk_write() to EEPROM.
- System wants to perform another write to EEPROM but EEPROM is still
busy with the last write.
- Because of high CPU load the usleep_range() will sleep more than
25 ms (at24_write_timeout).
- Within the over-long sleeping the EEPROM finished the previous write
operation and is ready again.
- at24_loop_until_timeout() will detect timeout and won't try to write.
Signed-off-by: Wang Xin <xin.wang7@cn.bosch.com> Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com> Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Currently, if the user specifies an unsupported mitigation strategy on the
kernel command line, it will be ignored silently. The code will fall back
to the default strategy, possibly leaving the system more vulnerable than
expected.
This may happen due to e.g. a simple typo, or, for a stable kernel release,
because not all mitigation strategies have been backported.
A recent change moved the microcode loader hotplug callback into the early
startup phase which is running with interrupts disabled. It missed that
the callbacks invoke sysfs functions which might sleep causing nice 'might
sleep' splats with proper debugging enabled.
Split the callbacks and only load the microcode in the early startup phase
and move the sysfs handling back into the later threaded and preemptible
bringup phase where it was before.
Fixes: 78f4e932f776 ("x86/microcode, cpuhotplug: Add a microcode loader CPU hotplug callback") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Borislav Petkov <bp@suse.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: stable@vger.kernel.org Cc: x86-ml <x86@kernel.org> Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1906182228350.1766@nanos.tec.linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The bits set in x86_spec_ctrl_mask are used to calculate the guest's value
of SPEC_CTRL that is written to the MSR before VMENTRY, and control which
mitigations the guest can enable. In the case of SSBD, unless the host has
enabled SSBD always on mode (by passing "spec_store_bypass_disable=on" in
the kernel parameters), the SSBD bit is not set in the mask and the guest
can not properly enable the SSBD always on mitigation mode.
This has been confirmed by running the SSBD PoC on a guest using the SSBD
always on mitigation mode (booted with kernel parameter
"spec_store_bypass_disable=on"), and verifying that the guest is vulnerable
unless the host is also using SSBD always on mode. In addition, the guest
OS incorrectly reports the SSB vulnerability as mitigated.
Always set the SSBD bit in x86_spec_ctrl_mask when the host CPU supports
it, allowing the guest to use SSBD whether or not the host has chosen to
enable the mitigation in any of its modes.
Fixes: be6fcb5478e9 ("x86/bugs: Rework spec_ctrl base and mask logic") Signed-off-by: Alejandro Jimenez <alejandro.j.jimenez@oracle.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Liam Merwick <liam.merwick@oracle.com> Reviewed-by: Mark Kanda <mark.kanda@oracle.com> Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Cc: bp@alien8.de Cc: rkrcmar@redhat.com Cc: kvm@vger.kernel.org Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/1560187210-11054-1-git-send-email-alejandro.j.jimenez@oracle.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Once we unlock adapter->hw_lock in pvscsi_queue_lck() nothing prevents just
queued scsi_cmnd from completing and freeing the request. Thus cmd->cmnd[0]
dereference can dereference already freed request leading to kernel crashes
or other issues (which one of our customers observed). Store cmd->cmnd[0]
in a local variable before unlocking adapter->hw_lock to fix the issue.
CC: <stable@vger.kernel.org> Signed-off-by: Jan Kara <jack@suse.cz> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Currently, although we submit super bios in order (and super.nr_entries
is incremented by each logged entry), submit_bio() is async so each
super sector may not be written to log device in order and then the
final nr_entries may be smaller than it should be.
This problem can be reproduced by the xfstests generic/455 with ext4:
QA output created by 455
-Silence is golden
+mark 'end' does not exist
Fix this by serializing submission of super sectors to make sure each
is written to the log disk in order.
Fixes: 0e9cebe724597 ("dm: add log writes target") Cc: stable@vger.kernel.org Signed-off-by: zhangyi (F) <yi.zhang@huawei.com> Suggested-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
load_flat_shared_library() is broken: It only calls load_flat_file() if
prepare_binprm() returns zero, but prepare_binprm() returns the number of
bytes read - so this only happens if the file is empty.
Instead, call into load_flat_file() if the number of bytes read is
non-negative. (Even if the number of bytes is zero - in that case,
load_flat_file() will see nullbytes and return a nice -ENOEXEC.)
In addition, remove the code related to bprm creds and stop using
prepare_binprm() - this code is loading a library, not a main executable,
and it only actually uses the members "buf", "file" and "filename" of the
linux_binprm struct. Instead, call kernel_read() directly.
Link: http://lkml.kernel.org/r/20190524201817.16509-1-jannh@google.com Fixes: 287980e49ffc ("remove lots of IS_ERR_VALUE abuses") Signed-off-by: Jann Horn <jannh@google.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Kees Cook <keescook@chromium.org> Cc: Nicolas Pitre <nicolas.pitre@linaro.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Russell King <linux@armlinux.org.uk> Cc: Greg Ungerer <gerg@linux-m68k.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
mpol_rebind_nodemask() is called for MPOL_BIND and MPOL_INTERLEAVE
mempoclicies when the tasks's cpuset's mems_allowed changes. For
policies created without MPOL_F_STATIC_NODES or MPOL_F_RELATIVE_NODES,
it works by remapping the policy's allowed nodes (stored in v.nodes)
using the previous value of mems_allowed (stored in
w.cpuset_mems_allowed) as the domain of map and the new mems_allowed
(passed as nodes) as the range of the map (see the comment of
bitmap_remap() for details).
The result of remapping is stored back as policy's nodemask in v.nodes,
and the new value of mems_allowed should be stored in
w.cpuset_mems_allowed to facilitate the next rebind, if it happens.
However, 213980c0f23b ("mm, mempolicy: simplify rebinding mempolicies
when updating cpusets") introduced a bug where the result of remapping
is stored in w.cpuset_mems_allowed instead. Thus, a mempolicy's
allowed nodes can evolve in an unexpected way after a series of
rebinding due to cpuset mems_allowed changes, possibly binding to a
wrong node or a smaller number of nodes which may e.g. overload them.
This patch fixes the bug so rebinding again works as intended.
[vbabka@suse.cz: new changlog] Link: http://lkml.kernel.org/r/ef6a69c6-c052-b067-8f2c-9d615c619bb9@suse.cz Link: http://lkml.kernel.org/r/1558768043-23184-1-git-send-email-zhongjiang@huawei.com Fixes: 213980c0f23b ("mm, mempolicy: simplify rebinding mempolicies when updating cpusets") Signed-off-by: zhong jiang <zhongjiang@huawei.com> Reviewed-by: Vlastimil Babka <vbabka@suse.cz> Cc: Oscar Salvador <osalvador@suse.de> Cc: Anshuman Khandual <khandual@linux.vnet.ibm.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Ralph Campbell <rcampbell@nvidia.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
0a1eb2d474ed ("fs/proc: Stop reporting eip and esp in /proc/PID/stat")
stopped reporting eip/esp and fd7d56270b52 ("fs/proc: Report eip/esp in
/prod/PID/stat for coredumping") reintroduced the feature to fix a
regression with userspace core dump handlers (such as minicoredumper).
Because PF_DUMPCORE is only set for the primary thread, this didn't fix
the original problem for secondary threads. Allow reporting the eip/esp
for all threads by checking for PF_EXITING as well. This is set for all
the other threads when they are killed. coredump_wait() waits for all the
tasks to become inactive before proceeding to invoke a core dumper.
Link: http://lkml.kernel.org/r/87y32p7i7a.fsf@linutronix.de Link: http://lkml.kernel.org/r/20190522161614.628-1-jlu@pengutronix.de Fixes: fd7d56270b526ca3 ("fs/proc: Report eip/esp in /prod/PID/stat for coredumping") Signed-off-by: John Ogness <john.ogness@linutronix.de> Reported-by: Jan Luebbe <jlu@pengutronix.de> Tested-by: Jan Luebbe <jlu@pengutronix.de> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Caused by too many confusing indirections and casts.
id->driver_info is a pointer stored in a long. We want the
pointer here, not the address of it.
Thanks-to: Hillf Danton <hdanton@sina.com> Reported-by: syzbot+b68605d7fadd21510de1@syzkaller.appspotmail.com Cc: Kristian Evensen <kristian.evensen@gmail.com> Fixes: e4bf63482c30 ("qmi_wwan: Add quirk for Quectel dynamic config") Signed-off-by: Bjørn Mork <bjorn@mork.no>
[Upstream commit did not apply because I shuffled two lines in the
backport. The fixes tag for 4.14 is 3a6a5107ceb3.]
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
the client c is always dereferenced to get the rdma struct, so c has to
be a valid pointer at this point.
Gcc would optimize that away but let's make coverity happy...
iattr is passed to v9fs_vfs_setattr_dotl which does send various
values from iattr over the wire, even if it tells the server to
only look at iattr.ia_valid fields this could leak some stack data.
9p/rdma would sometimes drop the connection and display errors in
recv_done when the user does ^C.
The errors were caused by recv buffers that were posted at the time
of disconnect, and we just do not want to disconnect when
down_interruptible is... interrupted.
If the xen bus exists but does not expose the proper interface, it is
possible to get a non-zero length but still some error, leading to
strcmp failing trying to load invalid memory addresses e.g. fffffffffffffffe.
There is then no need to check length when there is no error, as the
xenbus driver guarantees that the string is nul-terminated.
The call to sdma_progress() is called outside the wait lock.
In this case, there is a race condition where sdma_progress() can return
false and the sdma_engine can idle. If that happens, there will be no
more sdma interrupts to cause the wakeup and the user_sdma xmit will hang.
Fix by moving the lock to enclose the sdma_progress() call.
Also, delete busycount. The need for this was removed by:
commit bcad29137a97 ("IB/hfi1: Serve the most starved iowait entry first")
Ported to linux-4.14.y.
Cc: <stable@vger.kernel.org> Fixes: 7724105686e7 ("IB/hfi1: add driver files") Reviewed-by: Gary Leshner <Gary.S.Leshner@intel.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The strncpy() function may leave the destination string buffer
unterminated, better use strlcpy() that we have a __weak fallback
implementation for systems without it.
This fixes this warning on an Alpine Linux Edge system with gcc 8.2:
util/header.c: In function 'perf_event__synthesize_event_update_name':
util/header.c:3625:2: error: 'strncpy' output truncated before terminating nul copying as many bytes from a string as its length [-Werror=stringop-truncation]
strncpy(ev->data, evsel->name, len);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
util/header.c:3618:15: note: length computed here
size_t len = strlen(evsel->name);
^~~~~~~~~~~~~~~~~~~
Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Fixes: a6e5281780d1 ("perf tools: Add event_update event unit type") Link: https://lkml.kernel.org/n/tip-wycz66iy8dl2z3yifgqf894p@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Since we make sure the destination buffer has at least strlen(orig) + 1,
no need to do a strncpy(dest, orig, strlen(orig)), just use strcpy(dest,
orig).
This silences this gcc 8.2 warning on Alpine Linux:
In function 'add_man_viewer',
inlined from 'perf_help_config' at builtin-help.c:284:3:
builtin-help.c:192:2: error: 'strncpy' output truncated before terminating nul copying as many bytes from a string as its length [-Werror=stringop-truncation]
strncpy((*p)->name, name, len);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
builtin-help.c: In function 'perf_help_config':
builtin-help.c:187:15: note: length computed here
size_t len = strlen(name);
^~~~~~~~~~~~
Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Fixes: 078006012401 ("perf_counter tools: add in basic glue from Git") Link: https://lkml.kernel.org/n/tip-2f69l7drca427ob4km8i7kvo@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The strncpy() function may leave the destination string buffer
unterminated, better use strlcpy() that we have a __weak fallback
implementation for systems without it.
In this case we are actually setting the null byte at the right place,
but since we pass the buffer size as the limit to strncpy() and not
it minus one, gcc ends up warning us about that, see below. So, lets
just switch to the shorter form provided by strlcpy().
This fixes this warning on an Alpine Linux Edge system with gcc 8.2:
ui/tui/helpline.c: In function 'tui_helpline__push':
ui/tui/helpline.c:27:2: error: 'strncpy' specified bound 512 equals destination size [-Werror=stringop-truncation]
strncpy(ui_helpline__current, msg, sz)[sz - 1] = '\0';
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Fixes: e6e904687949 ("perf ui: Introduce struct ui_helpline") Link: https://lkml.kernel.org/n/tip-d1wz0hjjsh19xbalw69qpytj@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
As per the current design, in the case of sw crypto controlled devices,
it is the device which advertises the support for AP/VLAN iftype based
on it's ability to tranmsit packets encrypted in software
(In VLAN functionality, group traffic generated for a specific
VLAN group is always encrypted in software). Commit db3bdcb9c3ff
("mac80211: allow AP_VLAN operation on crypto controlled devices")
has introduced this change.
Since 4addr AP operation also uses AP/VLAN iftype, this conditional
way of advertising AP/VLAN support has broken 4addr AP mode operation on
crypto controlled devices which do not support VLAN functionality.
In the case of ath10k driver, not all firmwares have support for VLAN
functionality but all can support 4addr AP operation. Because AP/VLAN
support is not advertised for these devices, 4addr AP operations are
also blocked.
Fix this by allowing 4addr operation on devices which do not support
AP/VLAN iftype but can support 4addr AP operation (decision is based on
the wiphy flag WIPHY_FLAG_4ADDR_AP).
The HB port may not be available for various reasons. Either it has been
disabled by a config option or by the hypervisor for other reasons.
In that case, make sure we have a backup plan and use the backdoor port
instead with a performance penalty.
Pulling linux/prctl.h into asm/ptrace.h in the arm64 UAPI headers causes
userspace build issues for any program (e.g. strace and qemu) that
includes both <sys/prctl.h> and <linux/ptrace.h> when using musl libc:
| error: redefinition of 'struct prctl_mm_map'
| struct prctl_mm_map {
Although it's a bit grotty, fix this breakage by duplicating the prctl
constant definitions. Since these are part of the kernel ABI, they
cannot be changed in future and so it's not the end of the world to have
them open-coded.
Fixes: 43d4da2c45b2 ("arm64/sve: ptrace and ELF coredump support") Cc: stable@vger.kernel.org Acked-by: Dave Martin <Dave.Martin@arm.com> Signed-off-by: Anisse Astier <aastier@freebox.fr> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Because RISC-V compliant implementations can cache invalid entries
in TLB, an SFENCE.VMA is necessary after changes to the page table.
This patch adds an SFENCE.vma for the vmalloc_fault path.
Signed-off-by: ShihPo Hung <shihpo.hung@sifive.com>
[paul.walmsley@sifive.com: reversed tab->whitespace conversion,
wrapped comment lines] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com> Cc: Palmer Dabbelt <palmer@sifive.com> Cc: Albert Ou <aou@eecs.berkeley.edu> Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: linux-riscv@lists.infradead.org Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Since GCC 9, the compiler warns about evolution of the
platform-specific ABI, in particular relating for the marshaling of
certain structures involving bitfields.
The kernel is a standalone binary, and of course nobody would be
so stupid as to expose structs containing bitfields as function
arguments in ABI. (Passing a pointer to such a struct, however
inadvisable, should be unaffected by this change. perf and various
drivers rely on that.)
So these warnings do more harm than good: turn them off.
We may miss warnings about future ABI drift, but that's too bad.
Future ABI breaks of this class will have to be debugged and fixed
the traditional way unless the compiler evolves finer-grained
diagnostics.
Signed-off-by: Dave Martin <Dave.Martin@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We want SDIO drivers to be able to temporarily stop retuning when the
driver knows that the SDIO card is not in a state where retuning will
work (maybe because the card is asleep). We'll move the relevant
functions to a place where drivers can call them.
Cc: stable@vger.kernel.org #v4.18+ Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Acked-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Normally when the MMC core sees an "-EILSEQ" error returned by a host
controller then it will trigger a retuning of the card. This is
generally a good idea.
However, if a command is expected to sometimes cause transfer errors
then these transfer errors shouldn't cause a re-tuning. This
re-tuning will be a needless waste of time. One example case where a
transfer is expected to cause errors is when transitioning between
idle (sometimes referred to as "sleep" in Broadcom code) and active
state on certain Broadcom WiFi SDIO cards. Specifically if the card
was already transitioning between states when the command was sent it
could cause an error on the SDIO bus.
Let's add an API that the SDIO function drivers can call that will
temporarily disable the auto-tuning functionality. Then we can add a
call to this in the Broadcom WiFi driver and any other driver that
might have similar needs.
NOTE: this makes the assumption that the card is already tuned well
enough that it's OK to disable the auto-retuning during one of these
error-prone situations. Presumably the driver code performing the
error-prone transfer knows how to recover / retry from errors. ...and
after we can get back to a state where transfers are no longer
error-prone then we can enable the auto-retuning again. If we truly
find ourselves in a case where the card needs to be retuned sometimes
to handle one of these error-prone transfers then we can always try a
few transfers first without auto-retuning and then re-try with
auto-retuning if the first few fail.
Without this change on rk3288-veyron-minnie I periodically see this in
the logs of a machine just sitting there idle:
dwmmc_rockchip ff0d0000.dwmmc: Successfully tuned phase to XYZ
Cc: stable@vger.kernel.org #v4.18+ Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Acked-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The inline assembler functions ap_aqic() and ap_qact() used two
variables declared on the very same register. One variable was for
input only, the other for output. Looks like newer versions of the gcc
don't like this. Anyway it is a better coding to use one variable
(which may have a union data type) on one register for input and
output. So this patch introduces unions and uses only one variable now
for input and output for GR1 for the PQAP(QACT) and PQAP(QIC)
invocation.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com> Acked-by: Ilya Leoshkevich <iii@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
[heiko.carstens@de.ibm.com]:
-----
Laura Abbott reported that the kernel doesn't build anymore with gcc 9,
due to the "X" constraint. Ilya provided the gcc 9 patch "S/390:
Introduce jdd constraint" which introduces the new "jdd" constraint
which fixes this.
-----
The support for section anchors on S/390 introduced in gcc9 has changed
the behavior of "X" constraint, which can now produce register
references. Since existing constraints, in particular, "i", do not fit
the intended use case on S/390, the new machine-specific "jdd"
constraint was introduced. This patch makes jump labels use "jdd"
constraint when building with gcc9.
Reported-by: Laura Abbott <labbott@redhat.com> Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
ieee80211_aes_gmac() uses the mic argument directly in sg_set_buf() and
that does not allow use of stack memory (e.g., BUG_ON() is hit in
sg_set_buf() with CONFIG_DEBUG_SG). BIP GMAC TX side is fine for this
since it can use the skb data buffer, but the RX side was using a stack
variable for deriving the local MIC value to compare against the
received one.
Fix this by allocating heap memory for the mic buffer.
This was found with hwsim test case ap_cipher_bip_gmac_128 hitting that
BUG_ON() and kernel panic.
When receiving a deauthentication/disassociation frame from a TDLS
peer, a station should not disconnect the current AP, but only
disable the current TDLS link if it's enabled.
Without this change, a TDLS issue can be reproduced by following the
steps as below:
1. STA-1 and STA-2 are connected to AP, bidirection traffic is running
between STA-1 and STA-2.
2. Set up TDLS link between STA-1 and STA-2, stay for a while, then
teardown TDLS link.
3. Repeat step #2 and monitor the connection between STA and AP.
During the test, one STA may send a deauthentication/disassociation
frame to another, after TDLS teardown, with reason code 6/7, which
means: Class 2/3 frame received from nonassociated STA.
On receive this frame, the receiver STA will disconnect the current
AP and then reconnect. It's not a expected behavior, purpose of this
frame should be disabling the TDLS link, not the link with AP.
Cc: stable@vger.kernel.org Signed-off-by: Yu Wang <yyuwang@codeaurora.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When receiving a robust management frame, drop it if we don't have
rx->sta since then we don't have a security association and thus
couldn't possibly validate the frame.
Cc: stable@vger.kernel.org Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In wiphy_new_nm(), if an error occurs after dev_set_name() and
device_initialize() have already been called, it's necessary to call
put_device() (via wiphy_free()) to avoid a memory leak.
Reported-by: syzbot+7fddca22578bc67c3fe4@syzkaller.appspotmail.com Fixes: 1f87f7d3a3b4 ("cfg80211: add rfkill support") Cc: stable@vger.kernel.org Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Some servers such as Windows 10 will return STATUS_INSUFFICIENT_RESOURCES
as the number of simultaneous SMB3 requests grows (even though the client
has sufficient credits). Return EAGAIN on STATUS_INSUFFICIENT_RESOURCES
so that we can retry writes which fail with this status code.
This (for example) fixes large file copies to Windows 10 on fast networks.
Signed-off-by: Steve French <stfrench@microsoft.com> CC: Stable <stable@vger.kernel.org> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When trying to align the minimum encryption key size requirement for
Bluetooth connections, it turns out doing this in a central location in
the HCI connection handling code is not possible.
Original Bluetooth version up to 2.0 used a security model where the
L2CAP service would enforce authentication and encryption. Starting
with Bluetooth 2.1 and Secure Simple Pairing that model has changed into
that the connection initiator is responsible for providing an encrypted
ACL link before any L2CAP communication can happen.
Now connecting Bluetooth 2.1 or later devices with Bluetooth 2.0 and
before devices are causing a regression. The encryption key size check
needs to be moved out of the HCI connection handling into the L2CAP
channel setup.
To achieve this, the current check inside hci_conn_security() has been
moved into l2cap_check_enc_key_size() helper function and then called
from four decisions point inside L2CAP to cover all combinations of
Secure Simple Pairing enabled devices and device using legacy pairing
and legacy service security model.
Fixes: d5bb334a8e17 ("Bluetooth: Align minimum encryption key size for LE and BR/EDR connections")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=203643 Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The minimum encryption key size for LE connections is 56 bits and to
align LE with BR/EDR, enforce 56 bits of minimum encryption key size for
BR/EDR connections as well.
If UHS speed modes are enabled, a compatible SD card switches down to
1.8V during enumeration. If after this a software reboot/crash takes
place and on-chip ROM tries to enumerate the SD card, the difference in
IO voltages (host @ 3.3V and card @ 1.8V) may end up damaging the card.
The fix for this is to have support for power cycling the card in
hardware (with a PORz/soft-reset line causing a power cycle of the
card). Since am571x-, am572x- and am574x-idk don't have this
capability, disable voltage switching for these boards.
The major effect of this is that the maximum supported speed
mode is now high speed(50 MHz) down from SDR104(200 MHz).
Cc: <stable@vger.kernel.org> Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Since commit 1e434b703248 ("ARM: imx: update the cpu power up timing
setting on i.mx6sx") some characters loss is noticed on i.MX6ULL UART
as reported by Christoph Niedermaier.
The intention of such commit was to increase the SW2ISO field for i.MX6SX
only, but since cpuidle-imx6sx is also used on i.MX6UL/i.MX6ULL this caused
unintended side effects on other SoCs.
Fix this problem by keeping the original SW2ISO value for i.MX6UL/i.MX6ULL
and only increase SW2ISO in the i.MX6SX case.
Cc: stable@vger.kernel.org Fixes: 1e434b703248 ("ARM: imx: update the cpu power up timing setting on i.mx6sx") Reported-by: Christoph Niedermaier <cniedermaier@dh-electronics.com> Signed-off-by: Fabio Estevam <festevam@gmail.com> Tested-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com> Tested-by: Christoph Niedermaier <cniedermaier@dh-electronics.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
BPF_ALU64 div/mod operations are currently using signed division, unlike
BPF_ALU32 operations. Fix the same. DIV64 and MOD64 overflow tests pass
with this fix.
Fixes: 156d0e290e969c ("powerpc/ebpf/jit: Implement JIT compiler for extended BPF") Cc: stable@vger.kernel.org # v4.8+ Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
CAN supports software tx timestamps as of the below commit. Purge
any queued timestamp packets on socket destroy.
Fixes: 51f31cabe3ce ("ip: support for TX timestamps on UDP and RAW sockets") Reported-by: syzbot+a90604060cb40f5bdd16@syzkaller.appspotmail.com Signed-off-by: Willem de Bruijn <willemb@google.com> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Current we can meet timeout issue when setting a small bitrate like
10000 as follows on i.MX6UL EVK board (ipg clock = 66MHZ, per clock =
30MHZ):
| root@imx6ul7d:~# ip link set can0 up type can bitrate 10000
A link change request failed with some changes committed already.
Interface can0 may have been left with an inconsistent configuration,
please check.
| RTNETLINK answers: Connection timed out
It is caused by calling of flexcan_chip_unfreeze() timeout.
Originally the code is using usleep_range(10, 20) for unfreeze
operation, but the patch (8badd65 can: flexcan: avoid calling
usleep_range from interrupt context) changed it into udelay(10) which is
only a half delay of before, there're also some other delay changes.
After double to FLEXCAN_TIMEOUT_US to 100 can fix the issue.
Meanwhile, Rasmus Villemoes reported that even with a timeout of 100,
flexcan_probe() fails on the MPC8309, which requires a value of at least
140 to work reliably. 250 works for everyone.
Currently, btrfs does not consult seed devices to start readahead. As a
result, if readahead zone is added to the seed devices, btrfs_reada_wait()
indefinitely wait for the reada_ctl to finish.
You can reproduce the hung by modifying btrfs/163 to have larger initial
file size (e.g. xfs_io pwrite 4M instead of current 256K).
Fixes: 7414a03fbf9e ("btrfs: initial readahead code and prototypes") Cc: stable@vger.kernel.org # 3.2+: ce7791ffee1e: Btrfs: fix race between readahead and device replace/removal Cc: stable@vger.kernel.org # 3.2+ Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The Number of Namespaces (nn) field in the identify controller data structure is
defined as u32 and the maximum allowed value in NVMe specification is
0xFFFFFFFEUL. This change fixes the possible overflow of the DIV_ROUND_UP()
operation used in nvme_scan_ns_list() by casting the nn to u64.
Signed-off-by: Jaesoo Lee <jalee@purestorage.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Some chips have attributes which exist on more than one page but the
attribute is not presently marked as paged. This causes the attributes
to be generated with the same label, which makes it impossible for
userspace to tell them apart.
Marking all such attributes as paged would result in the page suffix
being added regardless of whether they were present on more than one
page or not, which might break existing setups. Therefore, we add a
second check which treats the attribute as paged, even if not marked as
such, if it is present on multiple pages.
Fixes: b4ce237b7f7d ("hwmon: (pmbus) Introduce infrastructure to detect sensors and limit registers") Signed-off-by: Robert Hancock <hancock@sedsystems.ca> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Drivers may register to hwmon and request for also registering
with the thermal subsystem (HWMON_C_REGISTER_TZ). However,
some of these driver, e.g. marvell phy, may be probed from
Device Tree or being dynamically allocated, and in the later
case, it will not have a dev->of_node entry.
Registering with hwmon without the dev->of_node may result in
different outcomes depending on the device tree, which may
be a bit misleading. If the device tree blob has no 'thermal-zones'
node, the *hwmon_device_register*() family functions are going
to gracefully succeed, because of-thermal,
*thermal_zone_of_sensor_register() return -ENODEV in this case,
and the hwmon error path handles this error code as success to
cover for the case where CONFIG_THERMAL_OF is not set.
However, if the device tree blob has the 'thermal-zones'
entry, the *hwmon_device_register*() will always fail on callers
with no dev->of_node, propagating -EINVAL.
If dev->of_node is not present, calling of-thermal does not
make sense. For this reason, this patch checks first if the
device has a of_node before going over the process of registering
with the thermal subsystem of-thermal interface. And in this case,
when a caller of *hwmon_device_register*() with HWMON_C_REGISTER_TZ
and no dev->of_node will still register with hwmon, but not with
the thermal subsystem. If all the hwmon part bits are in place,
the registration will succeed.
Enabling sysfs attribute bridge_hostnotify triggers a series of udev events
for the MAC addresses of all currently connected peers. In case no VLAN is
set for a peer, the device reports the corresponding MAC addresses with
VLAN ID 4096. This currently results in attribute VLAN=4096 for all
non-VLAN interfaces in the initial series of events after host-notify is
enabled.
Instead, no VLAN attribute should be reported in the udev event for
non-VLAN interfaces.
Only the initial events face this issue. For dynamic changes that are
reported later, the device uses a validity flag.
This also changes the code so that it now sets the VLAN attribute for
MAC addresses with VID 0. On Linux, no qeth interface will ever be
registered with VID 0: Linux kernel registers VID 0 on all network
interfaces initially, but qeth will drop .ndo_vlan_rx_add_vid for VID 0.
Peers with other OSs could register MACs with VID 0.
Fixes: 9f48b9db9a22 ("qeth: bridgeport support - address notifications") Signed-off-by: Alexandra Winter <wintera@linux.ibm.com> Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
There's some NICs, such as hinic, with NETIF_F_IP_CSUM and NETIF_F_TSO
on but NETIF_F_HW_CSUM off. And ipvlan device features will be
NETIF_F_TSO on with NETIF_F_IP_CSUM and NETIF_F_IP_CSUM both off as
IPVLAN_FEATURES only care about NETIF_F_HW_CSUM. So TSO will be
disabled in netdev_fix_features.
For example:
Features for enp129s0f0:
rx-checksumming: on
tx-checksumming: on
tx-checksum-ipv4: on
tx-checksum-ip-generic: off [fixed]
tx-checksum-ipv6: on
Fixes: a188222b6ed2 ("net: Rename NETIF_F_ALL_CSUM to NETIF_F_CSUM_MASK") Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
struct ufs_dev_cmd is the main container that supports device management
commands. In the case of a read descriptor request, we assume that the
proper space was allocated in dev_cmd to hold the returning descriptor.
This is no longer true, as there are flows that doesn't use dev_cmd for
device management requests, and was wrong in the first place.
Fixes: d44a5f98bb49 (ufs: query descriptor API) Signed-off-by: Avri Altman <avri.altman@wdc.com> Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com> Acked-by: Bean Huo <beanhuo@micron.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
As suggested by Masahiro Yamada, fix the above error using regular
expressions in the same way it was fixed for the `ARCH=x86` case via
commit fda9f9903be6 ("scripts/checkstack.pl: automatically handle
32-bit and 64-bit mode for ARCH=x86").
Suggested-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: George G. Davis <george_davis@mentor.com> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
On the Arm Juno platform, the HDLCD pixel clock is constrained to 250KHz
resolution in order to avoid the tiny System Control Processor spending
aeons trying to calculate exact PLL coefficients. This means that modes
like my oddball 1600x1200 with 130.89MHz clock get rejected since the
rate cannot be matched exactly. In practice, though, this mode works
quite happily with the clock at 131MHz, so let's relax the check to
allow a little bit of slop.
Signed-off-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Liviu Dudau <liviu.dudau@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Rather than allowing any old mode through, then subsequently refusing
unmatchable clock rates in atomic_check when it's too late to back out
and pick a different mode, let's do that validation up-front where it
will cause unsupported modes to be correctly pruned in the first place.
This also eliminates an issue whereby a perceived clock rate of 0 would
cause atomic disable to fail and prevent the module from being unloaded.
Signed-off-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Liviu Dudau <liviu.dudau@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Should only enable HW RX_2BYTE_OFFSET function in the case NET_IP_ALIGN
equals to 2.
Signed-off-by: Mark Lee <mark-mc.lee@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Should hw_feature as hardware capability flags to check if hardware LRO
got support.
Signed-off-by: Mark Lee <mark-mc.lee@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The PERF_EVENT_IOC_PERIOD ioctl command can be used to change the
sample period of a running perf_event. Consequently, when calculating
the next event period, the new period will only be considered after the
previous one has overflowed.
This patch changes the calculation of the remaining event ticks so that
they are offset if the period has changed.
See commit 3581fe0ef37c ("ARM: 7556/1: perf: fix updated event period in
response to PERF_EVENT_IOC_PERIOD") for details.
Signed-off-by: Young Xiao <92siuyang@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In get_vdev_port_node_info(), 'node_info->vdev_port.name' is allcoated
by kstrdup_const(), and it returns NULL when fails. So
'node_info->vdev_port.name' should be checked.
Signed-off-by: Gen Zhang <blackgod016574@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When doing a loopback test at copper ports, the serdes loopback
and the phy loopback will fail, because of the adjust link had
not finished, and phy not ready.
Adds sleep between adjust link and test process to fix it.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When non-bridged, non-vlan'ed mv88e6xxx port is moving down, error
message is logged:
failed to kill vid 0081/0 for device eth_cu_1000_4
This is caused by call from __vlan_vid_del() with vin set to zero, over
call chain this results into _mv88e6xxx_port_vlan_del() called with
vid=0, and mv88e6xxx_vtu_get() called from there returns -EINVAL.
On symmetric path moving port up, call goes through
mv88e6xxx_port_vlan_prepare() that calls mv88e6xxx_port_check_hw_vlan()
that returns -EOPNOTSUPP for zero vid.
This patch changes mv88e6xxx_vtu_get() to also return -EOPNOTSUPP for
zero vid, then this error code is explicitly cleared in
dsa_slave_vlan_rx_kill_vid() and error message is no longer logged.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com> Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Since commit 9012d011660ea5cf2 ("compiler: allow all arches to enable
CONFIG_OPTIMIZE_INLINING"), xtensa:tinyconfig fails to build with section
mismatch errors.
WARNING: vmlinux.o(.text.unlikely+0x68): Section mismatch in reference
from the function ___pa()
to the function .meminit.text:memblock_reserve()
WARNING: vmlinux.o(.text.unlikely+0x74): Section mismatch in reference
from the function mem_reserve()
to the function .meminit.text:memblock_reserve()
FATAL: modpost: Section mismatches detected.
This was not seen prior to the above mentioned commit because mem_reserve()
was always inlined.
Mark mem_reserve(() as __init_memblock to have it reside in the same
section as memblock_reserve().
arch/mips/kernel/uprobes.c: In function 'arch_uprobe_pre_xol':
arch/mips/kernel/uprobes.c:115:17: warning: variable 'epc' set but not used [-Wunused-but-set-variable]
It's never used since introduction in
commit 40e084a506eb ("MIPS: Add uprobes support.")
User applications can register memory regions for TID buffers that are not
aligned on page boundaries. Hfi1 is expected to pin those pages in memory
and cache the pages with mmu_rb. The rb tree will fail to insert pages
that are not aligned correctly.
Validate whether a given virtual address is page aligned before pinning.
Fixes: 7e7a436ecb6e ("staging/hfi1: Add TID entry program function body") Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com> Signed-off-by: Kamenee Arumugam <kamenee.arumugam@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The qpn allocation logic has a WARN_ON() that intends to detect the use of
an index that will introduce bits in the lower order bits of the QOS bits
in the QPN.
Unfortunately, it has the following bugs:
- it misfires when wrapping QPN allocation for non-QOS
- it doesn't correctly detect low order QOS bits (despite the comment)
The WARN_ON() should not be applied to non-QOS (qos_shift == 1).
Additionally, it SHOULD test the qpn bits per the table below:
Fix by qualifying the warning for qos_shift > 1 and producing the correct
mask to insure the above bits are zero without generating a superfluous
warning.
Fixes: 501edc42446e ("IB/rdmavt: Correct warning during QPN allocation") Reviewed-by: Kaike Wan <kaike.wan@intel.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Avoid such compiler warnings:
arch/parisc/math-emu/cnv_float.h:71:27: warning: ‘<<’ in boolean context, did you mean ‘<’ ? [-Wint-in-bool-context]
((Dintp1(dint_valueA) << 33 - SGL_EXP_LENGTH) || Dintp2(dint_valueB))
arch/parisc/math-emu/fcnvxf.c:257:6: note: in expansion of macro ‘Dint_isinexact_to_sgl’
if (Dint_isinexact_to_sgl(srcp1,srcp2)) {
After commit 4e5a74f1db8d ("parport: Revert "parport: fix
memory leak""), free_pardevice do not free par_dev->state,
we should free it in error path of parport_register_dev_model
before return.
GMAC controller on HSDK boards supports 256 Hash Table size so we need to
add the multicast filter bins property. This allows for the Hash filter
to work properly using stmmac driver.
Cc: Joao Pinto <jpinto@synopsys.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Acked-by: Alexey Brodkin <abrodkin@synopsys.com> Signed-off-by: Jose Abreu <joabreu@synopsys.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
| arch/arc/mm/tlb.c:914:2: warning: variable length array 'pd0' is used [-Wvla]
| arch/arc/include/asm/cmpxchg.h:95:29: warning: value computed is not used [-Wunused-value]
A packed AppArmor policy contains null-terminated tag strings that are read
by unpack_nameX(). However, unpack_nameX() uses string functions on them
without ensuring that they are actually null-terminated, potentially
leading to out-of-bounds accesses.
Make sure that the tag string is null-terminated before passing it to
strcmp().
Cc: stable@vger.kernel.org Fixes: 736ec752d95e ("AppArmor: policy routines for loading and unpacking policy") Signed-off-by: Jann Horn <jannh@google.com> Signed-off-by: John Johansen <john.johansen@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In the case of compat syscall ioctl numbers for UI_BEGIN_FF_UPLOAD and
UI_END_FF_UPLOAD need to be adjusted before being passed on
uinput_ioctl_handler() since code built with -m32 will be passing
slightly different values. Extend the code already covering
UI_SET_PHYS to cover UI_BEGIN_FF_UPLOAD and UI_END_FF_UPLOAD as well.
An endpoint conflict occurs when the USB is working in device mode
during an isochronous communication. When the endpointA IN direction
is an isochronous IN endpoint, and the host sends an IN token to
endpointA on another device, then the OUT transaction may be missed
regardless the OUT endpoint number. Generally, this occurs when the
device is connected to the host through a hub and other devices are
connected to the same hub.
The affected OUT endpoint can be either control, bulk, isochronous, or
an interrupt endpoint. After the OUT endpoint is primed, if an IN token
to the same endpoint number on another device is received, then the OUT
endpoint may be unprimed (cannot be detected by software), which causes
this endpoint to no longer respond to the host OUT token, and thus, no
corresponding interrupt occurs.
There is no good workaround for this issue, the only thing the software
could do is numbering isochronous IN from the highest endpoint since we
have observed most of device number endpoint from the lowest.
Cc: <stable@vger.kernel.org> #v3.14+ Cc: Fabio Estevam <festevam@gmail.com> Cc: Greg KH <gregkh@linuxfoundation.org> Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Cc: Jun Li <jun.li@nxp.com> Signed-off-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
UFS runtime suspend can be triggered after pm_runtime_enable() is invoked
in ufshcd_pltfrm_init(). However if the first runtime suspend is triggered
before binding ufs_hba structure to ufs device structure via
platform_set_drvdata(), then UFS runtime suspend will be no longer
triggered in the future because its dev->power.runtime_error was set in the
first triggering and does not have any chance to be cleared.
To be more clear, dev->power.runtime_error is set if hba is NULL in
ufshcd_runtime_suspend() which returns -EINVAL to rpm_callback() where
dev->power.runtime_error is set as -EINVAL. In this case, any future
rpm_suspend() for UFS device fails because rpm_check_suspend_allowed()
fails due to non-zero
dev->power.runtime_error.
To resolve this issue, make sure the first UFS runtime suspend get valid
"hba" in ufshcd_runtime_suspend(): Enable UFS runtime PM only after hba is
successfully bound to UFS device structure.
Fixes: 62694735ca95 ([SCSI] ufs: Add runtime PM support for UFS host controller driver) Cc: stable@vger.kernel.org Signed-off-by: Stanley Chu <stanley.chu@mediatek.com> Reviewed-by: Avri Altman <avri.altman@wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Processing of SDIO IRQs must obviously be prevented while the card is
system suspended, otherwise we may end up trying to communicate with an
uninitialized SDIO card.
Reports throughout the years shows that this is not only a theoretical
problem, but a real issue. So, let's finally fix this problem, by keeping
track of the state for the card and bail out before processing the SDIO
IRQ, in case the card is suspended.
Cc: stable@vger.kernel.org Reported-by: Douglas Anderson <dianders@chromium.org> Tested-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>