Sean Young [Thu, 23 Nov 2017 22:37:10 +0000 (17:37 -0500)]
media: cec: move cec autorepeat handling to rc-core
CEC autorepeat is different than other protocols. Autorepeat is triggered
by the first repeated user control pressed CEC message, rather than a
fixed REP_DELAY.
This change also does away with the KEY_UP event directly after the first
KEY_DOWN event, which was used to stop autorepeat from starting.
See commit a9a249a2c997 ("media: cec: fix remote control passthrough")
for the original change.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Chunyan Zhang [Mon, 6 Nov 2017 14:06:10 +0000 (09:06 -0500)]
media: rc: Replace timeval with ktime_t in imon.c
This patch changes the 32-bit time type (timeval) to the 64-bit one
(ktime_t), since 32-bit time types will break in the year 2038.
I use ktime_t instead of all uses of timeval in imon.c
This patch also changes do_gettimeofday() to ktime_get() accordingly,
since ktime_get returns a ktime_t, but do_gettimeofday returns a
struct timeval, and the other reason is that ktime_get() uses
the monotonic clock.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Sean Young [Thu, 2 Nov 2017 21:21:13 +0000 (17:21 -0400)]
media: lirc: allow lirc device to be opened more than once
This makes it possible for lircd to read from a lirc chardev, and not
keep it busy.
Note that this changes the default for timeout reports to on. lircd
already enables timeout reports when it opens a lirc device, leaving
them on until the next reboot.
Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Sean Young [Thu, 2 Nov 2017 20:39:16 +0000 (16:39 -0400)]
media: rc: move ir-lirc-codec.c contents into lirc_dev.c
Since removing the lirc kapi, ir-lirc-codec.c only contains lirc fops
so the file name is no longer correct. By moving its content into
lirc_dev.c the ugly extern struct lirc_fops is not longer needed,
and everything lirc related is in one file.
Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Sean Young [Sun, 8 Oct 2017 16:12:16 +0000 (12:12 -0400)]
kfifo: DECLARE_KIFO_PTR(fifo, u64) does not work on arm 32 bit
If you try to store u64 in a kfifo (or a struct with u64 members),
then the buf member of __STRUCT_KFIFO_PTR will cause 4 bytes
padding due to alignment (note that struct __kfifo is 20 bytes
on 32 bit).
That in turn causes the __is_kfifo_ptr() to fail, which is caught
by kfifo_alloc(), which now returns EINVAL.
So, ensure that __is_kfifo_ptr() compares to the right structure.
Signed-off-by: Sean Young <sean@mess.org> Acked-by: Stefani Seibold <stefani@seibold.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Sean Young [Sun, 24 Sep 2017 16:43:24 +0000 (12:43 -0400)]
media: lirc: scancode rc devices should have a lirc device too
Now that the lirc interface supports scancodes, RC scancode devices
can also have a lirc device. The only receiving feature they will have
enabled is LIRC_CAN_REC_SCANCODE.
Note that CEC devices have no lirc device, since they can be controlled
from their /dev/cecN chardev.
Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Sean Young [Sat, 25 Feb 2017 11:51:32 +0000 (06:51 -0500)]
media: lirc: implement reading scancode
This implements LIRC_MODE_SCANCODE reading from the lirc device. The
scancode can be read from the input device too, but with this interface
you get the rc protocol, keycode, toggle and repeat status in addition
to just the scancode.
int main()
{
int fd, mode, rc;
fd = open("/dev/lirc0", O_RDWR);
mode = LIRC_MODE_SCANCODE;
if (ioctl(fd, LIRC_SET_REC_MODE, &mode)) {
// kernel too old or lirc does not support transmit
}
struct lirc_scancode scancode;
while (read(fd, &scancode, sizeof(scancode)) == sizeof(scancode)) {
printf("protocol:%d scancode:0x%x toggle:%d repeat:%d\n",
scancode.rc_proto, scancode.scancode,
!!(scancode.flags & LIRC_SCANCODE_FLAG_TOGGLE),
!!(scancode.flags & LIRC_SCANCODE_FLAG_REPEAT));
}
close(fd);
}
Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Sean Young [Sat, 23 Sep 2017 21:44:03 +0000 (17:44 -0400)]
media: lirc: do not call close() or open() on unregistered devices
If a lirc chardev is held open after a device is unplugged, rc_close()
will be called after rc_unregister_device(). The driver is not expecting
any calls at this point, and the iguanair driver causes an oops in
this scenario.
rc_open() can be called when the device is removed too, by calling open
on the chardev whilst the device is being removed.
Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Sean Young [Sat, 23 Sep 2017 14:41:13 +0000 (10:41 -0400)]
media: lirc: lirc interface should not be a raw decoder
The lirc user interface exists as a raw decoder, which does not make
much sense for transmit-only devices.
In addition, we want to have lirc char devices for devices which do not
use raw IR, i.e. scancode only devices.
Note that rc-code, lirc_dev, ir-lirc-codec are now calling functions of
each other, so they've been merged into one module rc-core to avoid
circular dependencies.
Since ir-lirc-codec no longer exists as separate codec module, there is no
need for RC_DRIVER_IR_RAW_TX type drivers to call ir_raw_event_register().
Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Sean Young [Thu, 8 Jun 2017 09:10:41 +0000 (05:10 -0400)]
media: lirc: remove LIRCCODE and LIRC_GET_LENGTH
LIRCCODE is a lirc mode where a driver produces driver-dependent
codes for receive and transmit. No driver uses this any more. The
LIRC_GET_LENGTH ioctl was used for this mode only.
Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Sean Young [Tue, 24 Oct 2017 18:59:31 +0000 (14:59 -0400)]
media: staging: remove lirc_zilog driver
The ir-kbd-i2c driver behaves like the lirc_zilog driver, except it can
send raw IR and receives scancodes rather than lirccodes.
The lirc_zilog driver only polls if the lirc chardev is opened;
similarly the ir-kbd-i2c driver only polls if the corresponding input
device is opened, or the lirc device.
Polling is disabled during IR transmission through the mutex.
The polling period is 402ms in the ir-kdb-i2c driver, and 260ms in the
lirc_zilog driver.
Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Sean Young [Tue, 24 Oct 2017 21:04:16 +0000 (17:04 -0400)]
media: i2c: enable i2c IR for hardware which isn't HD-PVR
This is a fix for commit 329d88da4df9 ("[media] media: i2c: Don't export
ir-kbd-i2c module alias") that stopped the module from being loaded
automagically.
The problems described only affect the HD-PVR, so it should not affect
other hardware; also if the module happens to be loaded, the i2c IR
part of the HD-PVR will be enabled anyway.
Fixes: 329d88da4df9 ("[media] media: i2c: Don't export ir-kbd-i2c module alias") Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Sean Young [Sat, 21 Oct 2017 12:16:47 +0000 (08:16 -0400)]
media: rc: implement zilog transmitter
This code implements the transmitter which is currently implemented
in the staging lirc_zilog driver.
The new code does not need a signal database, iow. the
haup-ir-blaster.bin firmware file is no longer needed, and the driver
does not know anything about the keycodes in that file.
Instead, the new driver can send raw IR, but the hardware is limited
to few different lengths of pulse and spaces, so it is best to use
generated IR rather than recorded IR.
Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Sean Young [Thu, 12 Oct 2017 22:02:57 +0000 (18:02 -0400)]
media: merge ir_tx_z8f0811_haup and ir_rx_z8f0811_haup i2c devices
These two devices ids are really just one device with multiple
addresses. Probing becomes much simpler if we simply fold this into
one i2c device with two address.
Note that this breaks the lirc_zilog driver, however we will teach
ir-kbd-i2c to do what lirc_zilog does in a later commit.
Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Akinobu Mita [Thu, 12 Oct 2017 16:04:44 +0000 (12:04 -0400)]
media: xilinx-video: fix bad of_node_put() on endpoint error
When iterating through all endpoints using of_graph_get_next_endpoint(),
the refcount of the returned endpoint node is incremented and the refcount
of the node which is passed as previous endpoint is decremented.
So the caller doesn't need to call of_node_put() for each iterated node
except for error exit paths. Otherwise we get "OF: ERROR: Bad
of_node_put() on ..." messages.
Colin Ian King [Wed, 20 Sep 2017 22:19:59 +0000 (18:19 -0400)]
media: dvb_ca_en50221: sanity check slot number from userspace
Currently a user can pass in an unsanitized slot number which
will lead to and out of range index into ca->slot_info. Fix this
by checking that the slot number is no more than the allowed
maximum number of slots. Seems that this bug has been in the driver
forever.
Detected by CoverityScan, CID#139381 ("Untrusted pointer read")
Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Jasmin Jessich <jasmin@anw.at> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add suffix ULL to constant 65535 in order to avoid a potential
integer overflow. This constant is used in a context that
expects an expression of type u64.
Stefan Brüns [Fri, 17 Feb 2017 00:55:33 +0000 (19:55 -0500)]
media: dvbsky: MyGica T230C support
Mygica T230 DVB-T/T2/C USB stick support. It uses the same FX2/Si2168
bridge/demodulator combo as the other devices supported by the driver,
but uses the Si2141 tuner.
Several DVB-T (MPEG2) and DVB-T2 (H.265) channels were tested, as well as
the included remote control.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Daniel Scheller [Wed, 6 Dec 2017 17:59:14 +0000 (12:59 -0500)]
media: ddbridge: improve error handling logic on fe attach failures
This change makes sure that demod frontends are always detached whenever
a tuner frontend attach failed. Achieve this by moving the detach-on-
failure logic at the end of dvb_input_attach(), and adding a goto to this
block on every tuner attach failure case, so if an error occurs, there are
no stray attached frontends left. As a side effect, this removes some
duplicated code.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Jaedon Shin [Fri, 1 Dec 2017 12:31:30 +0000 (07:31 -0500)]
media: dvb_frontend: Add commands implementation for compat ioct
The dtv_properties structure and the dtv_property structure are
different sizes in 32-bit and 64-bit system. This patch provides
FE_SET_PROPERTY and FE_GET_PROPERTY ioctl commands implementation for
32-bit user space applications.
drivers/media/dvb-core/dvb_frontend.c:154:2-7: WARNING: NULL check before freeing functions like kfree, debugfs_remove, debugfs_remove_recursive or usb_free_urb is not needed. Maybe consider reorganizing relevant code to avoid passing NULL values.
NULL check before some freeing functions is not needed.
Based on checkpatch warning
"kfree(NULL) is safe this check is probably not required"
and kfreeaddr.cocci by Julia Lawall.
Daniel Scheller [Sun, 26 Nov 2017 13:00:06 +0000 (08:00 -0500)]
media: dvb-frontends/stv0910: remove unneeded check/call to get_if_freq
The result (if any) isn't used anywhere besides being assigned to a local
variable (and the only current companion stv6111 doesn't even implement
get_if_frequency()), thus remove the ptr check and the call, and also
remove the now unused iffreq variable.
Reported-by: Richard Scobie <rascobie@slingshot.co.nz> Cc: Ralph Metzler <rjkm@metzlerbros.de> Signed-off-by: Daniel Scheller <d.scheller@gmx.net> Tested-by: Richard Scobie <rascobie@slingshot.co.nz> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Daniel Scheller [Sun, 26 Nov 2017 13:00:04 +0000 (08:00 -0500)]
media: dvb-frontends/stv0910: WARN_ON() on consecutive mutex_unlock()
Stack dump when gate_ctrl() is called in a way that consecutive unlocks
happen. This is a clear indication that other drivers interfacing with
the stv0910 driver don't do things properly or don't check for failures,
so dump stack so that those drivers can be identified and fixed.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net> Tested-by: Richard Scobie <rascobie@slingshot.co.nz> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Daniel Scheller [Sun, 26 Nov 2017 13:00:03 +0000 (08:00 -0500)]
media: frontends/stv0910: add field offsets to field defines
Each field (FSTV0910_XX) is declared as reg/off/unused/sign/mask. Add
the missing offset value to the defines.
Picked up from dddvb master, commit 8a1f27c3d22c ("add field offset to
field defines") by Ralph Metzler <rjkm@metzlerbros.de>, adapted to
match the comment style in the mainline driver.
Cc: Ralph Metzler <rjkm@metzlerbros.de> Signed-off-by: Daniel Scheller <d.scheller@gmx.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Vasyl Gomonovych [Mon, 20 Nov 2017 22:46:47 +0000 (17:46 -0500)]
media: c8sectpfe: Use resource_size function on memory resource
To adapt fei->sram_size calculation via resource_size for memory size
calculation before, in fei->sram = devm_ioremap_resource(dev, res).
And make memory initialization range in
memset_io for fei->sram appropriate
media: c8sectpfe: fix potential NULL pointer dereference in c8sectpfe_timer_interrupt
_channel_ is being dereferenced before it is null checked, hence there is a
potential null pointer dereference. Fix this by moving the pointer dereference
after _channel_ has been null checked.
This issue was detected with the help of Coccinelle.
Fixes: c5f5d0f99794 ("[media] c8sectpfe: STiH407/10 Linux DVB demux support") Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com> Acked-by: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The correct error code when a function is not defined is
-ENOTSUPP. It was typoed wrong as -EOPNOTSUPP, with,
unfortunately, exists, but it is not used by the DVB core.
Thanks-to: Geert Uytterhoeven <geert@linux-m68k.org> Thanks-to: Arnd Bergmann <arnd@arndb.de>
To make me revisit this code.
Fixes: a9cb97c3e628 ("media: dvb_frontend: be sure to init dvb_frontend_handle_ioctl() return code") Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The logic at V4L2 led core assumes that the flash struct
can be null. However, it doesn't check for null while
trying to set, causing some smatch to warn:
drivers/media/v4l2-core/v4l2-flash-led-class.c:210 v4l2_flash_s_ctrl() error: we previously assumed 'fled_cdev' could be null (see line 200)
media: dvb_frontend: be sure to init dvb_frontend_handle_ioctl() return code
As smatch warned:
drivers/media/dvb-core/dvb_frontend.c:2468 dvb_frontend_handle_ioctl() error: uninitialized symbol 'err'.
The ioctl handler actually got a regression here: before changeset d73dcf0cdb95 ("media: dvb_frontend: cleanup ioctl handling logic"),
the code used to return -EOPNOTSUPP if an ioctl handler was not
implemented on a driver. After the change, it may return a random
value.
As reported by smatch:
drivers/media/usb/dvb-usb-v2/mxl111sf-demod.c:485 mxl111sf_demod_read_signal_strength() error: uninitialized symbol 'modulation'.
The mxl111sf_demod_read_signal_strength() just ignores if something
gets wrong while reading snr or modulation.
As warned by smatch:
drivers/media/dvb-frontends/drxd_hard.c:989 HI_Command() error: uninitialized symbol 'waitCmd'.
drivers/media/dvb-frontends/drxd_hard.c:1306 SC_WaitForReady() error: uninitialized symbol 'curCmd'.
drivers/media/dvb-frontends/drxd_hard.c:1322 SC_SendCommand() error: uninitialized symbol 'errCode'.
drivers/media/dvb-frontends/drxd_hard.c:1339 SC_ProcStartCommand() error: uninitialized symbol 'scExec'.
The error handling on several places are somewhat flawed, as
they don't check if Read16() returns an error.
media: cxd2841er: ensure that status will always be available
The loop with read status use a dynamic timeout value, calculated
from symbol rate. It should run the loop at least one time for
the status to be handled after the loop.
While this should, in practice, happen every time, it doesn't
hurt to change the logic to make it explicit.
This solves a smatch warning:
drivers/media/dvb-frontends/cxd2841er.c:3350 cxd2841er_set_frontend_s() error: uninitialized symbol 'status'.
Smatch gives two bogus warnings on this driver:
drivers/media/usb/dvb-usb-v2/dvbsky.c:336 dvbsky_s960_attach() error: uninitialized symbol 'i2c_adapter'.
drivers/media/usb/dvb-usb-v2/dvbsky.c:459 dvbsky_s960c_attach() error: uninitialized symbol 'i2c_adapter'.
media: m88rs2000: handle the case where tuner doesn't have get_frequency
If the tuner doesn't have get_frequency() callback, the current
code will place a random value as the frequency offset. That
doesn't seem right! The better is to just assume that, on such
case, the tuner was able to set the exact frequency that was
requested.
Fixes a smatch warning:
drivers/media/dvb-frontends/m88rs2000.c:639 m88rs2000_set_frontend() error: uninitialized symbol 'tuner_freq'.
media: pt1: fix logic when pt1_nr_tables is zero or negative
pt1_nr_tables is a modprobe parameter. The way the logic
handles it, it can't be negative. However, user can
set it to zero.
If set to zero, however, it will cause troubles at
pt1_init_tables(), as reported by smatch:
drivers/media/pci/pt1/pt1.c:468 pt1_init_tables() error: uninitialized symbol 'first_pfn'.
The smatch logic gets confused with the syntax used to check if the
ov9650x_read() reads succedded:
drivers/media/i2c/ov9650.c:895 __g_volatile_ctrl() error: uninitialized symbol 'reg2'.
drivers/media/i2c/ov9650.c:895 __g_volatile_ctrl() error: uninitialized symbol 'reg1'.
There's nothing wrong with the original logic, except that
it is a little more harder to review.
So, let's stick with the syntax that won't cause read
issues.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com> Reviewed-by: Nicholas Mc Guire <hofrat@osadl.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As warned by smatch:
drivers/media/dvb-frontends/mb86a16.c:1690 mb86a16_read_ber() error: uninitialized symbol 'timer'.
drivers/media/dvb-frontends/mb86a16.c:1706 mb86a16_read_ber() error: uninitialized symbol 'timer'.
There is a potential risk of doing a division by zero if
timer is not handled well. Enforce it by setting a bit mask
for the values used to select the timer.
It should be noticed that I don't have mb86a16 datasheet. So,
the bitmask was guessed based on the existing checks for
the field. At worse case scenario, it will just show a
badly calculated bit error rate, but it won't crash.
While here, optimize the logic to prevent uneeded tests.
media: mb86a16: be more resilient if I2C fails on sync
If the I2C read fails while check for sync, there's no point
on doing adjusting the tuner due to a random value that might
be at VIRM var. So, set VIRM to zero, as that makes the caller
for check_sync() to return an error.
Fix those smatch warnings:
drivers/media/dvb-frontends/mb86a16.c:1460 mb86a16_set_fe() error: uninitialized symbol 'VIRM'.
drivers/media/dvb-frontends/mb86a16.c:1461 mb86a16_set_fe() error: uninitialized symbol 'VIRM'.
media: imx274: don't randomly return if range_count is zero
As smatch reported:
drivers/media/i2c/imx274.c:659 imx274_regmap_util_write_table_8() error: uninitialized symbol 'err'.
There is a bug at imx274_regmap_util_write_table_8() with causes
it to randomly return a random error if range_count is zero.
Worse than that, the logic there starts with range_count
equal to zero, and periodically resets it to zero again.
As it is a way more likely that err assumes a non-zero value,
I suspect that the chance of this code to run is very small,
so, it would be worth to review the entire function.
Anyway, clearly it shouldn't be returning error if range_count
is zero. So, let's fix it.
media: stv090x: Only print tuner lock if get_status is available
The current code doesn't report tuner lock properly if the
tuner get_status callback is not available, as reported by
smatch:
drivers/media/dvb-frontends/stv090x.c:2220 stv090x_get_coldlock() error: uninitialized symbol 'reg'.
projects / mirror_ubuntu-jammy-kernel.git / log