Manjunatha GK [Fri, 11 Dec 2009 05:39:08 +0000 (11:09 +0530)]
i2c-omap: OMAP3: Fix I2C lockup during timeout/error cases
Current OMAP3 I2C driver code does not follow the correct sequence for soft
reset. Due to this, lock up issues are reported during timeout/error cases.
This patch fixes above issue by disabling I2C controller as per OMAP3430 TRM
for soft reset. As per TRM, I2C controller needs to be disabled as a first
step during soft reset.
Here is correct soft reset sequence:
a. Ensure that the module is disabled
(clear the I2Ci.I2C_CON[15] I2C_EN bit to 0).
b. Set the I2Ci.I2C_SYSC[1] SRST bit to 1.
c. Enable the module by setting I2Ci.I2C_CON[15] I2C_EN bit to 1.
d. Check the I2Ci.I2C_SYSS[0] RDONE bit until it is set to 1 to
indicate the software reset is complete.
Cory Maccarrone [Wed, 23 Dec 2009 01:06:13 +0000 (18:06 -0700)]
i2c-omap: Don't write IE state in unidle if 0
Commit ef871432... (i2c-omap: OMAP3: PM: (re)init for every transfer
to support off-mode) introduced a change which make the dev->iestate
contents be written to the OMAP_I2C_IE_REG every time omap_i2c_unidle
is called. Previously, the state was only written if it wasn't equal
to zero.
In omap_i2c_probe, omap_i2c_unidle() is called prior to omap_i2c_init(),
in which case dev->iestate has not yet been initialized and will be set
to zero. Having this value written to the registers causes deadlock
while booting.
As such, this change restores the original functionality.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Sonic Zhang [Mon, 21 Dec 2009 14:28:30 +0000 (09:28 -0500)]
i2c-bfin-twi: fix CLKDIV calculation
Calculation of the CLKDIV speed setting should be done using base 10 math
rather than base 2. We also avoid exceeding the spec due to integer
truncation and a 50% duty cycle.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Linus Torvalds [Tue, 22 Dec 2009 22:22:05 +0000 (14:22 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
PM: Runtime PM documentation update
PM / Runtime: Use device type and device class callbacks
PM: Use pm_runtime_put_sync in system resume
PM: Measure device suspend and resume times
PM: Make the initcall_debug style timing for suspend/resume complete
Linus Torvalds [Tue, 22 Dec 2009 22:18:13 +0000 (14:18 -0800)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (36 commits)
powerpc/gc/wii: Remove get_irq_desc()
powerpc/gc/wii: hlwd-pic: convert irq_desc.lock to raw_spinlock
powerpc/gamecube/wii: Fix off-by-one error in ugecon/usbgecko_udbg
powerpc/mpic: Fix problem that affinity is not updated
powerpc/mm: Fix stupid bug in subpge protection handling
powerpc/iseries: use DECLARE_COMPLETION_ONSTACK for non-constant completion
powerpc: Fix MSI support on U4 bridge PCIe slot
powerpc: Handle VSX alignment faults correctly in little-endian mode
powerpc/mm: Fix typo of cpumask_clear_cpu()
powerpc/mm: Fix hash_utils_64.c compile errors with DEBUG enabled.
powerpc: Convert BUG() to use unreachable()
powerpc/pseries: Make declarations of cpu_hotplug_driver_lock() ANSI compatible.
powerpc/pseries: Don't panic when H_PROD fails during cpu-online.
powerpc/mm: Fix a WARN_ON() with CONFIG_DEBUG_PAGEALLOC and CONFIG_DEBUG_VM
powerpc/defconfigs: Set HZ=100 on pseries and ppc64 defconfigs
powerpc/defconfigs: Disable token ring in powerpc defconfigs
powerpc/defconfigs: Reduce 64bit vmlinux by making acenic and cramfs modules
powerpc/pseries: Select XICS and PCI_MSI PSERIES
powerpc/85xx: Wrong variable returned on error
powerpc/iseries: Convert to proc_fops
...
Stefani Seibold [Mon, 21 Dec 2009 22:37:33 +0000 (14:37 -0800)]
media video cx23888 driver: ported to new kfifo API
Fix the cx23888 driver to use the new kfifo API. Using kfifo_reset()
may result in a possible race conditions. This patch fixes it by using
a spinlock around the kfifo_reset() function.
Signed-off-by: Stefani Seibold <stefani@seibold.net> Cc: Mauro Carvalho Chehab <mchehab@infradead.org> Reviewed-by: Andy Walls <awalls@radix.net> Acked-by: Andy Walls <awalls@radix.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stefani Seibold [Mon, 21 Dec 2009 22:37:32 +0000 (14:37 -0800)]
kfifo: add record handling functions
Add kfifo_in_rec() - puts some record data into the FIFO
Add kfifo_out_rec() - gets some record data from the FIFO
Add kfifo_from_user_rec() - puts some data from user space into the FIFO
Add kfifo_to_user_rec() - gets data from the FIFO and write it to user space
Add kfifo_peek_rec() - gets the size of the next FIFO record field
Add kfifo_skip_rec() - skip the next fifo out record
Add kfifo_avail_rec() - determinate the number of bytes available in a record FIFO
Stefani Seibold [Mon, 21 Dec 2009 22:37:31 +0000 (14:37 -0800)]
kfifo: add kfifo_skip, kfifo_from_user and kfifo_to_user
Add kfifo_reset_out() for save lockless discard the fifo output
Add kfifo_skip() to skip a number of output bytes
Add kfifo_from_user() to copy user space data into the fifo
Add kfifo_to_user() to copy fifo data to user space
Stefani Seibold [Mon, 21 Dec 2009 22:37:30 +0000 (14:37 -0800)]
kfifo: add DEFINE_KFIFO and friends, add very tiny functions
Add DECLARE_KFIFO - macro to declare a kfifo and the associated buffer inside a struct
Add INIT_KFIFO - Initialize a kfifo declared by DECLARED_KFIFO
Add DEFINE_KFIFO - macro to define and initialize a kfifo as a global or local object
Add kfifo_size() - returns the size of the fifo in bytes
Add kfifo_is_empty() - returns true if the fifo is empty
Add kfifo_is_full() - returns true if the fifo is full
Add kfifo_avail() - returns the number of bytes available in the FIFO
Do some code cleanup
Stefani Seibold [Mon, 21 Dec 2009 22:37:27 +0000 (14:37 -0800)]
kfifo: move out spinlock
Move the pointer to the spinlock out of struct kfifo. Most users in
tree do not actually use a spinlock, so the few exceptions now have to
call kfifo_{get,put}_locked, which takes an extra argument to a
spinlock.
Stefani Seibold [Mon, 21 Dec 2009 22:37:26 +0000 (14:37 -0800)]
kfifo: move struct kfifo in place
This is a new generic kernel FIFO implementation.
The current kernel fifo API is not very widely used, because it has to
many constrains. Only 17 files in the current 2.6.31-rc5 used it.
FIFO's are like list's a very basic thing and a kfifo API which handles
the most use case would save a lot of development time and memory
resources.
I think this are the reasons why kfifo is not in use:
- The API is to simple, important functions are missing
- A fifo can be only allocated dynamically
- There is a requirement of a spinlock whether you need it or not
- There is no support for data records inside a fifo
So I decided to extend the kfifo in a more generic way without blowing up
the API to much. The new API has the following benefits:
- Generic usage: For kernel internal use and/or device driver.
- Provide an API for the most use case.
- Slim API: The whole API provides 25 functions.
- Linux style habit.
- DECLARE_KFIFO, DEFINE_KFIFO and INIT_KFIFO Macros
- Direct copy_to_user from the fifo and copy_from_user into the fifo.
- The kfifo itself is an in place member of the using data structure, this save an
indirection access and does not waste the kernel allocator.
- Lockless access: if only one reader and one writer is active on the fifo,
which is the common use case, no additional locking is necessary.
- Remove spinlock - give the user the freedom of choice what kind of locking to use if
one is required.
- Ability to handle records. Three type of records are supported:
- Variable length records between 0-255 bytes, with a record size
field of 1 bytes.
- Variable length records between 0-65535 bytes, with a record size
field of 2 bytes.
- Fixed size records, which no record size field.
- Preserve memory resource.
- Performance!
- Easy to use!
This patch:
Since most users want to have the kfifo as part of another object,
reorganize the code to allow including struct kfifo in another data
structure. This requires changing the kfifo_alloc and kfifo_init
prototypes so that we pass an existing kfifo pointer into them. This
patch changes the implementation and all existing users.
Randy Dunlap [Mon, 21 Dec 2009 22:37:22 +0000 (14:37 -0800)]
lib/string.c: fix kernel-doc warnings
Fix kernel-doc warnings (@arg name) in string.c::skip_spaces().
Warning(lib/string.c:347): No description found for parameter 'str'
Warning(lib/string.c:347): Excess function parameter 's' description in 'skip_spaces'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
"Petr Titěra reported an issue where he saw odd atime regressions with
2.6.33 where there were a full second worth of nanoseconds in the
nanoseconds field.
He also reviewed the time code and narrowed down the problem: unhandled
overflow of the nanosecond field caused by rounding up the
sub-nanosecond accumulated time.
Details:
* At the end of update_wall_time(), we currently round up the
sub-nanosecond portion of accumulated time when storing it into xtime.
This was added to avoid time inconsistencies caused when the
sub-nanosecond portion was truncated when storing into xtime.
Unfortunately we don't handle the possible second overflow caused by
that rounding.
* Previously the xtime_cache code hid this overflow by normalizing the
xtime value when storing into the xtime_cache.
* We could try to handle the second overflow after the rounding up, but
since this affects the timekeeping's internal state, this would further
complicate the next accumulation cycle, causing small errors in ntp
steering. As much as I'd like to get rid of it, the xtime_cache code is
known to work.
* The correct fix is really to include the sub-nanosecond portion in the
timekeeping accessor function, so we don't need to round up at during
accumulation. This would greatly simplify the accumulation code.
Unfortunately, we can't do this safely until the last three
non-GENERIC_TIME arches (sparc32, arm, cris) are converted (those
patches are in -mm) and we kill off the spots where arches set xtime
directly. This is all 2.6.34 material, so I think reverting the
xtime_cache change is the best approach for now.
Many thanks to Petr for both reporting and finding the issue!"
Reported-by: Petr Titěra <P.Titera@century.cz> Requested-by: john stultz <johnstul@us.ibm.com> Cc: Ingo Molnar <mingo@elte.hu> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PM / Runtime: Use device type and device class callbacks
The power management of some devices is handled through device types
and device classes rather than through bus types. Since these
devices may also benefit from using the run-time power management
core, extend it so that the device type and device class run-time PM
callbacks can be taken into consideration by it if the bus type
callback is not defined.
Update the run-time PM core documentation to reflect this change.
Al Viro [Sat, 19 Dec 2009 15:15:07 +0000 (10:15 -0500)]
Sanitize f_flags helpers
* pull ACC_MODE to fs.h; we have several copies all over the place
* nightmarish expression calculating f_mode by f_flags deserves a helper
too (OPEN_FMODE(flags))
Al Viro [Sat, 19 Dec 2009 15:10:39 +0000 (10:10 -0500)]
Fix f_flags/f_mode in case of lookup_instantiate_filp() from open(pathname, 3)
Just set f_flags when shoving struct file into nameidata; don't
postpone that until __dentry_open(). do_filp_open() has correct
value; lookup_instantiate_filp() doesn't - we lose the difference
between O_RDWR and 3 by that point.
We still set .intent.open.flags, so no fs code needs to be changed.
Roland Dreier [Fri, 18 Dec 2009 17:41:24 +0000 (09:41 -0800)]
anonfd: Allow making anon files read-only
It seems a couple places such as arch/ia64/kernel/perfmon.c and
drivers/infiniband/core/uverbs_main.c could use anon_inode_getfile()
instead of a private pseudo-fs + alloc_file(), if only there were a way
to get a read-only file. So provide this by having anon_inode_getfile()
create a read-only file if we pass O_RDONLY in flags.
Signed-off-by: Roland Dreier <rolandd@cisco.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Arnd Bergmann [Mon, 21 Dec 2009 16:53:53 +0000 (17:53 +0100)]
fs/compat_ioctl.c: fix build error when !BLOCK
No driver uses SG_SET_TRANSFORM any more in Linux, since the ide-scsi
driver was removed in 2.6.29. The compat-ioctl cleanup series moved
the handling for this around, which broke building without CONFIG_BLOCK.
Roland Dreier [Wed, 16 Dec 2009 20:48:44 +0000 (12:48 -0800)]
alloc_file(): simplify handling of mnt_clone_write() errors
When alloc_file() and init_file() were combined, the error handling of
mnt_clone_write() was taken into alloc_file() in a somewhat obfuscated
way. Since we don't use the error code for anything except warning,
we might as well warn directly without an extra variable.
Signed-off-by: Roland Dreier <rolandd@cisco.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Sonic Zhang [Tue, 14 Jul 2009 17:39:47 +0000 (13:39 -0400)]
pata_bf54x: handle portmuxing of pins through GPIO PORTs
By default, the PATA pins are routed to the async address lines in which
case, no peripheral muxing needs to be done. However, if the pins get
routed through the GPIO PORTs pins, we need to make sure to request them
so that the muxing is properly set up.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
resources: fix call to alignf() in allocate_resource()
The second parameter to alignf() in allocate_resource() must
reflect what new resource is attempted to be allocated, else
functions like pcibios_align_resource() (at least on x86) or
pcmcia_align() can't work correctly.
Commit 1e5ad9679016275d422e36b12a98b0927d76f556 broke this by
setting the "new" resource until we're about to return success.
To keep the resource untouched when allocate_resource() fails,
a "tmp" resource is introduced.
Linus Torvalds [Mon, 21 Dec 2009 18:13:37 +0000 (10:13 -0800)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
pata_cmd64x: fix overclocking of UDMA0-2 modes
Revert "pata_cmd64x: implement serialization as per notes"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
bnx2: Fix bnx2_netif_stop() merge error.
gianfar: Fix bit definitions of IMASK_GRSC and IMASK_GTSC
gianfar: Fix stats support
gianfar: Fix a filer bug
bnx2: fixing a timout error due not refreshing TX timers correctly
can/at91: don't check platform_get_irq's return value against zero
mISDN: use DECLARE_COMPLETION_ONSTACK for non-constant completion
bnx2: reset_task is crashing the kernel. Fixing it.
ipv6: fix an oops when force unload ipv6 module
TI DaVinci EMAC: Fix MDIO bus frequency configuration
e100: Fix broken cbs accounting due to missing memset.
broadcom: bcm54xx_shadow_read() errors ignored in bcm54xx_adjust_rxrefclk()
e1000e: LED settings in EEPROM ignored on 82571 and 82572
netxen: use module parameter correctly
netns: fix net.ipv6.route.gc_min_interval_ms in netns
Bluetooth: Prevent ill-timed autosuspend in USB driver
Bluetooth: Fix L2CAP locking scheme regression
Bluetooth: Ack L2CAP I-frames before retransmit missing packet
Bluetooth: Fix unset of RemoteBusy flag for L2CAP
Bluetooth: Fix PTR_ERR return of wrong pointer in hidp_setup_hid()
Linus Torvalds [Mon, 21 Dec 2009 18:10:23 +0000 (10:10 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (24 commits)
ALSA: sbawe: fix memory detection
ALSA: fix incorrect rounding direction in snd_interval_ratnum()
ALSA: HDA: add powersaving hook for Realtek
ALSA: HDA: remove useless mixers on Aspire 8930G
ALSA: HDA: simplify Aspire 8930G verb array
ALSA: hda: Set Front Mic to input vref 50% for Lenovo 3000 Y410
ALSA: hda/realtek: Remove extra .capsrc_nids initialization for ALC889_INTEL
ALSA: Use kzalloc for allocating only one thing
ALSA: AACI: switch to per-pcm locking
ALSA: AACI: add double-rate support
ALSA: AACI: factor common hw_params logic into aaci_pcm_hw_params
ALSA: AACI: cleanup aaci_pcm_hw_params
ALSA: AACI: simplify codec rate information
ALSA: aaci - Fix a typo
ASoC: wm8974: fix a wrong bit definition
sound: sgio2audio/pdaudiocf/usb-audio: initialize PCM buffer
ALSA: hda - Fix quirk for Maxdata obook4-1
ALSA: hda - Fix missing capsrc_nids for ALC88x
ALSA: hda - Make use of beep device found in Dell Vostro 1015n
ALSA: hda - Fixed internal mic initialization for Dell Vostro 1015
...
Krzysztof Helt [Sat, 19 Dec 2009 17:31:04 +0000 (18:31 +0100)]
ALSA: fix incorrect rounding direction in snd_interval_ratnum()
The direction of rounding is incorrect in the snd_interval_ratnum()
It was detected with following parameters (sb8 driver playing
8kHz stereo file):
- num is always 1000000
- requested frequency rate is from 7999 to 7999 (single frequency)
The first loop calculates div_down(num, freq->min) which is 125.
Thus, a frequency range's minimum value is 1000000 / 125 = 8000 Hz.
The second loop calculates div_up(num, freq->max) which is 126
The frequency range's maximum value is 1000000 / 126 = 7936 Hz.
The range maximum is lower than the range minimum so the function
fails due to empty result range.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Hector Martin [Sun, 20 Dec 2009 21:51:31 +0000 (22:51 +0100)]
ALSA: HDA: add powersaving hook for Realtek
The current Realtek code makes no specific provision for turning stuff
off. The codec chip is placed into low-power mode generically, but this
doesn't turn off any external hardware connected to it, in particular
external amplifiers.
This patch creates a hook function that is called by the codec
suspend/resume functions. It ought to disable any external hardware in a
device-specific way. I've implemented a generic ALC889 function that
sets the EAPD pin properly, and used it for the Acer Aspire 8930G which
can benefit from this feature.
On my laptop, this results in ~0.5W extra savings.
Signed-off-by: Hector Martin <hector@marcansoft.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Hector Martin [Sun, 20 Dec 2009 21:51:18 +0000 (22:51 +0100)]
ALSA: HDA: simplify Aspire 8930G verb array
This patch just simplifies the 8930G verb array a bit. Just use the
common ALC889 EAPD verb array to make things more consistent. The file
is already huge enough already.
Signed-off-by: Hector Martin <hector@marcansoft.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
J. Bruce Fields [Sun, 20 Dec 2009 15:43:35 +0000 (10:43 -0500)]
nfsd: fix "insecure" export option
A typo in 12045a6ee9908b "nfsd: let "insecure" flag vary by
pseudoflavor" reversed the sense of the "insecure" flag.
Reported-by: Michael Guntsche <mike@it-loops.com> Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Stern [Mon, 21 Dec 2009 01:46:11 +0000 (02:46 +0100)]
PM: Use pm_runtime_put_sync in system resume
This patch (as1317) fixes a bug in the PM core. When a device is
resumed following a system sleep, the core decrements the device's
runtime PM usage counter but doesn't issue an idle notification if the
counter reaches 0. This could prevent an otherwise unused device from
being runtime-suspended again after the system sleep.
The fix is to call pm_runtime_put_sync() instead of
pm_runtime_put_noidle().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Albert Herranz [Fri, 18 Dec 2009 10:04:05 +0000 (10:04 +0000)]
powerpc/gc/wii: Remove get_irq_desc()
Fix the following build failures:
arch/powerpc/platforms/embedded6xx/flipper-pic.c: In function 'flipper_pic_map':
arch/powerpc/platforms/embedded6xx/flipper-pic.c:105: error: implicit declaration of function 'get_irq_desc'
arch/powerpc/platforms/embedded6xx/hlwd-pic.c: In function 'hlwd_pic_map':
arch/powerpc/platforms/embedded6xx/hlwd-pic.c:98: error: implicit declaration of function 'get_irq_desc'
These failures are caused by the changes introduced in commit
"powerpc: Remove get_irq_desc()". The reason these drivers were not
updated is that they weren't merged yet.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Albert Herranz [Fri, 18 Dec 2009 10:04:42 +0000 (10:04 +0000)]
powerpc/gc/wii: hlwd-pic: convert irq_desc.lock to raw_spinlock
Fix the following build failures:
arch/powerpc/platforms/embedded6xx/hlwd-pic.c: In function 'hlwd_pic_irq_cascade':
arch/powerpc/platforms/embedded6xx/hlwd-pic.c:135: error: passing argument 1 of 'spin_lock' from incompatible pointer type
arch/powerpc/platforms/embedded6xx/hlwd-pic.c:137: error: passing argument 1 of 'spin_unlock' from incompatible pointer type
arch/powerpc/platforms/embedded6xx/hlwd-pic.c:145: error: passing argument 1 of 'spin_lock' from incompatible pointer type
arch/powerpc/platforms/embedded6xx/hlwd-pic.c:149: error: passing argument 1 of 'spin_unlock' from incompatible pointer type
These failures are caused by the changes introduced in commit
"genirq: Convert irq_desc.lock to raw_spinlock". The reason this driver
was not updated is that it wasn't merged yet.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Peter Zijlstra [Sun, 20 Dec 2009 16:36:27 +0000 (17:36 +0100)]
sched: Fix hotplug hang
The hot-unplug kstopmachine usage does a wakeup after
deactivating the cpu, hence we cannot use cpu_active()
here but must rely on the good olde online.
Reported-by: Sachin Sant <sachinp@in.ibm.com> Reported-by: Jens Axboe <jens.axboe@oracle.com> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Tested-by: Jens Axboe <jens.axboe@oracle.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
LKML-Reference: <1261326987.4314.24.camel@laptop> Signed-off-by: Ingo Molnar <mingo@elte.hu>
adev->dma_mode stores the transfer mode value not UDMA mode number
so the condition in cmd64x_set_dmamode() is always true and the higher
UDMA clock is always selected. This can potentially result in data
corruption when UDMA33 device is used, when 40-wire cable is used or
when the error recovery code decides to lower the device speed down.
The issue was introduced in the commit 6a40da0 ("libata cmd64x: whack
into a shape that looks like the documentation") which goes back to
kernel 2.6.20.
Cc: stable@kernel.org Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Peter Zijlstra [Sun, 20 Dec 2009 13:23:57 +0000 (14:23 +0100)]
sched: Restore printk sanity
Revert the braindead pr_* crap. (Commit 663997d "sched: Use
pr_fmt() and pr_<level>()")
It's dumb and causes stupid "sched: " strings all over the place.
Signed-off-by: Peter Zijlstra <peterz@infradead.org> Acked-by: Mike Galbraith <efault@gmx.de> Cc: Joe Perches <joe@perches.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <1261315437.4314.6.camel@laptop>
[ i dont mind the pr_*() patterns that much - but Peter dislikes them with a vengence. ]
[ - v2: remove spurious diffstat from changelog :-/ ] Signed-off-by: Ingo Molnar <mingo@elte.hu>
Linus Torvalds [Sat, 19 Dec 2009 20:38:55 +0000 (12:38 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha-2.6:
alpha: Convert BUG() to use unreachable()
alpha: Add minimal support for software performance events
alpha: Wire up missing/new syscalls
Linus Torvalds [Sat, 19 Dec 2009 19:04:29 +0000 (11:04 -0800)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
sata_mv: remove pointless NULL test
pata_hpt3x2n: fix clock turnaround
libata: fix reporting of drained bytes when clearing DRQ
sata_mv: add power management support for the PCI controllers.
sata_mv: store the board_idx into the host private data
pata_octeon_cf: use resource_size(), to fix resource sizing bug
libata: use the WRITE_SAME_16 define
sata_mv: move the PCI bar description initialization code
sata_mv: add power management support for the platform driver
sata_mv: support clkdev framework
sata_mv: increase PIO IORDY timeout
Linus Torvalds [Sat, 19 Dec 2009 17:48:42 +0000 (09:48 -0800)]
Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf session: Make events_stats u64 to avoid overflow on 32-bit arches
hw-breakpoints: Fix hardware breakpoints -> perf events dependency
perf events: Dont report side-band events on each cpu for per-task-per-cpu events
perf events, x86/stacktrace: Fix performance/softlockup by providing a special frame pointer-only stack walker
perf events, x86/stacktrace: Make stack walking optional
perf events: Remove unused perf_counter.h header file
perf probe: Check new event name
kprobe-tracer: Check new event/group name
perf probe: Check whether debugfs path is correct
perf probe: Fix libdwarf include path for Debian
Linus Torvalds [Sat, 19 Dec 2009 17:48:14 +0000 (09:48 -0800)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, irq: Allow 0xff for /proc/irq/[n]/smp_affinity on an 8-cpu system
Makefile: Unexport LC_ALL instead of clearing it
x86: Fix objdump version check in arch/x86/tools/chkobjdump.awk
x86: Reenable TSC sync check at boot, even with NONSTOP_TSC
x86: Don't use POSIX character classes in gen-insn-attr-x86.awk
Makefile: set LC_CTYPE, LC_COLLATE, LC_NUMERIC to C
x86: Increase MAX_EARLY_RES; insufficient on 32-bit NUMA
x86: Fix checking of SRAT when node 0 ram is not from 0
x86, cpuid: Add "volatile" to asm in native_cpuid()
x86, msr: msrs_alloc/free for CONFIG_SMP=n
x86, amd: Get multi-node CPU info from NodeId MSR instead of PCI config space
x86: Add IA32_TSC_AUX MSR and use it
x86, msr/cpuid: Register enough minors for the MSR and CPUID drivers
initramfs: add missing decompressor error check
bzip2: Add missing checks for malloc returning NULL
bzip2/lzma/gzip: pre-boot malloc doesn't return NULL on failure
Linus Torvalds [Sat, 19 Dec 2009 17:47:49 +0000 (09:47 -0800)]
Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (25 commits)
sched: Fix broken assertion
sched: Assert task state bits at build time
sched: Update task_state_arraypwith new states
sched: Add missing state chars to TASK_STATE_TO_CHAR_STR
sched: Move TASK_STATE_TO_CHAR_STR near the TASK_state bits
sched: Teach might_sleep() about preemptible RCU
sched: Make warning less noisy
sched: Simplify set_task_cpu()
sched: Remove the cfs_rq dependency from set_task_cpu()
sched: Add pre and post wakeup hooks
sched: Move kthread_bind() back to kthread.c
sched: Fix select_task_rq() vs hotplug issues
sched: Fix sched_exec() balancing
sched: Ensure set_task_cpu() is never called on blocked tasks
sched: Use TASK_WAKING for fork wakups
sched: Select_task_rq_fair() must honour SD_LOAD_BALANCE
sched: Fix task_hot() test order
sched: Fix set_cpu_active() in cpu_down()
sched: Mark boot-cpu active before smp_init()
sched: Fix cpu_clock() in NMIs, on !CONFIG_HAVE_UNSTABLE_SCHED_CLOCK
...
Linus Torvalds [Sat, 19 Dec 2009 17:47:34 +0000 (09:47 -0800)]
Merge branch 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sys: Fix missing rcu protection for __task_cred() access
signals: Fix more rcu assumptions
signal: Fix racy access to __task_cred in kill_pid_info_as_uid()
Linus Torvalds [Sat, 19 Dec 2009 17:47:18 +0000 (09:47 -0800)]
Merge branch 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
timers: Remove duplicate setting of new_base in __mod_timer()
clockevents: Prevent clockevent_devices list corruption on cpu hotplug
Linus Torvalds [Sat, 19 Dec 2009 17:46:46 +0000 (09:46 -0800)]
Merge branch 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] Use strim instead of strstrip to avoid false warnings.
[S390] qdio: add counter for input queue full condition
[S390] qdio: remove superfluous log entries and WARN_ONs.
[S390] ptrace: dont abuse PT_PTRACED
[S390] cio: fix channel path vary
[S390] drivers: Correct size given to memset
[S390] tape: Add pr_fmt() macro to all tape source files
[S390] rename NT_PRXSTATUS to NT_S390_HIGHREGS
[S390] tty: PTR_ERR return of wrong pointer in fs3270_open()
[S390] s390: PTR_ERR return of wrong pointer in fallback_init_cip()
[S390] dasd: PTR_ERR return of wrong pointer in
[S390] dasd: move dasd-diag kmsg to dasd
[S390] cio: fix drvdata usage for the console subchannel
[S390] wire up sys_recvmmsg
Al Viro [Sat, 19 Dec 2009 16:03:30 +0000 (16:03 +0000)]
fix more leaks in audit_tree.c tag_chunk()
Several leaks in audit_tree didn't get caught by commit 318b6d3d7ddbcad3d6867e630711b8a705d873d7, including the leak on normal
exit in case of multiple rules refering to the same chunk.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viro [Sat, 19 Dec 2009 15:59:45 +0000 (15:59 +0000)]
fix braindamage in audit_tree.c untag_chunk()
... aka "Al had badly fscked up when writing that thing and nobody
noticed until Eric had fixed leaks that used to mask the breakage".
The function essentially creates a copy of old array sans one element
and replaces the references to elements of original (they are on cyclic
lists) with those to corresponding elements of new one. After that the
old one is fair game for freeing.
First of all, there's a dumb braino: when we get to list_replace_init we
use indices for wrong arrays - position in new one with the old array
and vice versa.
Another bug is more subtle - termination condition is wrong if the
element to be excluded happens to be the last one. We shouldn't go
until we fill the new array, we should go until we'd finished the old
one. Otherwise the element we are trying to kill will remain on the
cyclic lists...
That crap used to be masked by several leaks, so it was not quite
trivial to hit. Eric had fixed some of those leaks a while ago and the
shit had hit the fan...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sandeep Gopalpet [Wed, 16 Dec 2009 01:15:07 +0000 (01:15 +0000)]
gianfar: Fix stats support
This patch updates the per rx/tx queue stats.
To update the per rx queue stats a new structure has been
introduced rx_q_stats.
The per tx queue stats are updated via the netdev_queue
structure itself.
Note that we update only the tx_packtes, tx_bytes, rx_packets,
rx_bytes and rx_dropped stats on a per queue basis.
Signed-off-by: Sandeep Gopalpet <Sandeep.Kumar@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sandeep Gopalpet [Wed, 16 Dec 2009 01:14:58 +0000 (01:14 +0000)]
gianfar: Fix a filer bug
We need to enable filer whenever we need to use multiple RX
queues. Also, need to program RIR0 register with the required
distribution we require, if using RX filer hashing support for
packet distribution to multiple queues.
Signed-off-by: Sandeep Gopalpet <Sandeep.Kumar@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Breno Leitao [Sat, 19 Dec 2009 04:35:34 +0000 (20:35 -0800)]
bnx2: fixing a timout error due not refreshing TX timers correctly
When running the following script on an active bnx2 interface:
while(true); do ifconfig ethX mtu 9000; ifconfig ethX mtu 1500; done
A timeout error appears and dumps the following stack:
NETDEV WATCHDOG: eth4 (bnx2): transmit queue 0 timed out
------------[ cut here ]------------
Badness at net/sched/sch_generic.c:261
<snip>
This patch just fixes the way that ->trans_start is refreshed.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com> Acked-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Uwe Kleine-König [Sat, 19 Dec 2009 04:31:56 +0000 (20:31 -0800)]
can/at91: don't check platform_get_irq's return value against zero
platform_get_irq returns -ENXIO on failure, so !irq was probably
always true. Better use (int)irq <= 0. Note that a return value of
zero is still handled as error even though this could mean irq0.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Breno Leitao [Sat, 19 Dec 2009 04:29:04 +0000 (20:29 -0800)]
bnx2: reset_task is crashing the kernel. Fixing it.
If bnx2 schedules a reset via the reset_task, e.g., due to a TX
timeout, it's possible for the NIC to be disabled with packets
pending for transmit. In this case, napi_disable will loop forever,
eventually crashing the kernel. This patch moves the disable of
the device to after the napi_disable call.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com> Acked-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yang Hongyang [Sat, 19 Dec 2009 04:25:13 +0000 (20:25 -0800)]
ipv6: fix an oops when force unload ipv6 module
When I do an ipv6 module force unload,I got the following oops:
#rmmod -f ipv6
------------[ cut here ]------------
kernel BUG at mm/slub.c:2969!
invalid opcode: 0000 [#1] SMP
last sysfs file: /sys/devices/pci0000:00/0000:00:11.0/0000:02:03.0/net/eth2/ifindex
Modules linked in: ipv6(-) dm_multipath uinput ppdev tpm_tis tpm tpm_bios pcspkr pcnet32 mii parport_pc i2c_piix4 parport i2c_core floppy mptspi mptscsih mptbase scsi_transport_spi
It's because in ip6_frags_ns_sysctl_register,
"table" only alloced when "net" is not equals
to "init_net".So when we free "table" in
ip6_frags_ns_sysctl_unregister,we should check
this first.
This patch fix the problem.
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
TI DaVinci EMAC: Fix MDIO bus frequency configuration
There was a typo in "if condition" checking for validity of MDIO
bus frequency passed as part of platform data. Bitwise AND was
being used instead of a Logical AND.
Tested on: DM6467 EVM
Signed-off-by: Nageswari Srinivasan <nageswari@ti.com> Acked-by: Anant Gole <anantgole@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Roger Oksanen [Sat, 19 Dec 2009 04:18:21 +0000 (20:18 -0800)]
e100: Fix broken cbs accounting due to missing memset.
Alan Stern noticed that e100 caused slab corruption.
commit 98468efddb101f8a29af974101c17ba513b07be1 changed
the allocation of cbs to use dma pools that don't return zeroed memory,
especially the cb->status field used to track which cb to clean, causing
(the visible) double freeing of skbs and a wrong free cbs count.
Now the cbs are explicitly zeroed at allocation time.
Reported-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Roger Oksanen <roger.oksanen@cs.helsinki.fi> Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Sat, 19 Dec 2009 04:14:59 +0000 (20:14 -0800)]
e1000e: LED settings in EEPROM ignored on 82571 and 82572
Do not override the customizable LED configuration set in the EEPROM.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Netxen driver is doing this bogus thing to create a control file.
This fails if device doesn't exist, and overall is a bad way to do
the module parameter. Rather than fix borked code, just rewrite.
Just using a writeable module parameter of 0/1 is the correct way
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Fri, 18 Dec 2009 17:48:35 +0000 (17:48 +0000)]
ALSA: AACI: simplify codec rate information
There's no need for a specific rule; ALSA's generic AC'97 support
calculates the necessary rate constraint information itself, and
we can use this directly.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Jan Glauber [Fri, 18 Dec 2009 16:43:26 +0000 (17:43 +0100)]
[S390] qdio: add counter for input queue full condition
Add a counter to the qdio performance statistics that indicates that no
free buffers were left in the input queue. If the counter gets increased
it means that the qdio adapter filled all available buffers and possibly
had more buffers ready but could not transmit them.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Jan Glauber [Fri, 18 Dec 2009 16:43:25 +0000 (17:43 +0100)]
[S390] qdio: remove superfluous log entries and WARN_ONs.
* Don't write debug feature log entries for sl, slsb and sbal since these
elements can be located from the qdio_q pointer which is also logged.
* Convert WARN_ON for wrong alignment of sbal to BUG_ON.
* Remove WARN_ON's for wrong alignment of q / qib / slib since these
alignments should be guaranteed by kmem_cache_alloc alignment /
struct aligned attribute / __get_free_page.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Channel path vary is currently broken: channel paths which are varied
offline are still used by Linux. The reason for this is that:
* the path mask indicating which paths of an I/O device can be used
is reset by each internal I/O request
* the logic that checks if a path group is already in its designated
target state incorrectly interprets the result "is correctly set"
as "is correctly set and available"
Fix this by resetting the path mask only for internal I/O requests
which affect the path mask and by correcting the pgid check logic.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Michael Holzheu [Fri, 18 Dec 2009 16:43:21 +0000 (17:43 +0100)]
[S390] tape: Add pr_fmt() macro to all tape source files
Without defining the pr_fmt() macro, the "tape: " prefix will not be
printed when using the pr_xxx printk macros. This patch adds the
missing definitions.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
projects / mirror_ubuntu-disco-kernel.git / log