Zumeng Chen [Mon, 4 Dec 2017 03:22:02 +0000 (11:22 +0800)]
gianfar: fix a flooded alignment reports because of padding issue.
According to LS1021A RM, the value of PAL can be set so that the start of the
IP header in the receive data buffer is aligned to a 32-bit boundary. Normally,
setting PAL = 2 provides minimal padding to ensure such alignment of the IP
header.
However every incoming packet's 8-byte time stamp will be inserted into the
packet data buffer as padding alignment bytes when hardware time stamping is
enabled.
So we set the padding 8+2 here to avoid the flooded alignment faults:
Johannes Berg [Sat, 2 Dec 2017 07:41:55 +0000 (08:41 +0100)]
Revert "net: core: maybe return -EEXIST in __dev_alloc_name"
This reverts commit d6f295e9def0; some userspace (in the case
we noticed it's wpa_supplicant), is relying on the current
error code to determine that a fixed name interface already
exists.
Reported-by: Jouni Malinen <j@w1.fi> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Previously we swapped the tx_packets, tx_bytes and tx_dropped counters
with rx_packets, rx_bytes and rx_dropped counters, respectively. This
behaviour is correct and expected for VF representors but it should not
be swapped for physical port mac representors.
Fixes: eadfa4c3be99 ("nfp: add stats and xmit helpers for representors") Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 4 Dec 2017 19:32:02 +0000 (11:32 -0800)]
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio fixes from Michael Tsirkin:
"virtio and qemu bugfixes
A couple of bugfixes that just became ready"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_balloon: fix increment of vb->num_pfns in fill_balloon()
virtio: release virtio index when fail to device_register
fw_cfg: fix driver remove
1) Various TCP control block fixes, including one that crashes with
SELinux, from David Ahern and Eric Dumazet.
2) Fix ACK generation in rxrpc, from David Howells.
3) ipvlan doesn't set the mark properly in the ipv4 route lookup key,
from Gao Feng.
4) SIT configuration doesn't take on the frag_off ipv4 field
configuration properly, fix from Hangbin Liu.
5) TSO can fail after device down/up on stmmac, fix from Lars Persson.
6) Various bpftool fixes (mostly in JSON handling) from Quentin Monnet.
7) Various SKB leak fixes in vhost/tun/tap (mostly observed as
performance problems). From Wei Xu.
8) mvpps's TX descriptors were not zero initialized, from Yan Markman.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (57 commits)
tcp: use IPCB instead of TCP_SKB_CB in inet_exact_dif_match()
tcp: add tcp_v4_fill_cb()/tcp_v4_restore_cb()
rxrpc: Fix the MAINTAINERS record
rxrpc: Use correct netns source in rxrpc_release_sock()
liquidio: fix incorrect indentation of assignment statement
stmmac: reset last TSO segment size after device open
ipvlan: Add the skb->mark as flow4's member to lookup route
s390/qeth: build max size GSO skbs on L2 devices
s390/qeth: fix GSO throughput regression
s390/qeth: fix thinko in IPv4 multicast address tracking
tap: free skb if flags error
tun: free skb in early errors
vhost: fix skb leak in handle_rx()
bnxt_en: Fix a variable scoping in bnxt_hwrm_do_send_msg()
bnxt_en: fix dst/src fid for vxlan encap/decap actions
bnxt_en: wildcard smac while creating tunnel decap filter
bnxt_en: Need to unconditionally shut down RoCE in bnxt_shutdown
phylink: ensure we take the link down when phylink_stop() is called
sfp: warn about modules requiring address change sequence
sfp: improve RX_LOS handling
...
Chris Metcalf [Mon, 4 Dec 2017 15:52:40 +0000 (10:52 -0500)]
arch/tile: mark as orphaned
The chip family of TILEPro and TILE-Gx was developed by Tilera, which
was eventually acquired by Mellanox. The tile architecture was added to
the kernel in 2010 and first appeared in 2.6.36.
Now at Mellanox we are developing new chips based on the ARM64
architecture; our last TILE-Gx chip (the Gx72) was released in 2013, and
our customers using tile architecture products are not, as far as we
know, looking to upgrade to newer kernel releases. In the absence of
someone in the community stepping up to take over maintainership, this
commit marks the architecture as orphaned.
Cc: Chris Metcalf <metcalf@alum.mit.edu> Signed-off-by: Chris Metcalf <cmetcalf@mellanox.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix a compilation warning in xdp redirect tracepoint due to
missing bpf.h include that pulls in struct bpf_map, from Xie.
2) Limit the maximum number of attachable BPF progs for a given
perf event as long as uabi is not frozen yet. The hard upper
limit is now 64 and therefore the same as with BPF multi-prog
for cgroups. Also add related error checking for the sample
BPF loader when enabling and attaching to the perf event, from
Yonghong.
3) Specifically set the RLIMIT_MEMLOCK for the test_verifier_log
case, so that the test case can always pass and not fail in
some environments due to too low default limit, also from
Yonghong.
4) Fix up a missing license header comment for kernel/bpf/offload.c,
from Jakub.
5) Several fixes for bpftool, among others a crash on incorrect
arguments when json output is used, error message handling
fixes on unknown options and proper destruction of json writer
for some exit cases, all from Quentin.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
James Morris reported kernel stack corruption bug that
we tracked back to commit 971f10eca186 ("tcp: better TCP_SKB_CB
layout to reduce cache line misses")
First patch needs to be backported to kernels >= 3.18,
while second patch needs to be backported to kernels >= 4.9, since
this was the time when inet_exact_dif_match appeared.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Sun, 3 Dec 2017 17:33:00 +0000 (09:33 -0800)]
tcp: use IPCB instead of TCP_SKB_CB in inet_exact_dif_match()
After this fix : ("tcp: add tcp_v4_fill_cb()/tcp_v4_restore_cb()"),
socket lookups happen while skb->cb[] has not been mangled yet by TCP.
Fixes: a04a480d4392 ("net: Require exact match for TCP socket lookups if dif is l3mdev") Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 3 Dec 2017 17:32:59 +0000 (09:32 -0800)]
tcp: add tcp_v4_fill_cb()/tcp_v4_restore_cb()
James Morris reported kernel stack corruption bug [1] while
running the SELinux testsuite, and bisected to a recent
commit bffa72cf7f9d ("net: sk_buff rbnode reorg")
We believe this commit is fine, but exposes an older bug.
SELinux code runs from tcp_filter() and might send an ICMP,
expecting IP options to be found in skb->cb[] using regular IPCB placement.
We need to defer TCP mangling of skb->cb[] after tcp_filter() calls.
This patch adds tcp_v4_fill_cb()/tcp_v4_restore_cb() in a very
similar way we added them for IPv6.
Fixes: 971f10eca186 ("tcp: better TCP_SKB_CB layout to reduce cache line misses") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: James Morris <james.l.morris@oracle.com> Tested-by: James Morris <james.l.morris@oracle.com> Tested-by: Casey Schaufler <casey@schaufler-ca.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 3 Dec 2017 15:51:08 +0000 (10:51 -0500)]
Merge branch 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM fix from Russell King:
"Just one fix this time around, for the late commit in the merge window
that triggered a problem with qemu. Qemu is apparently also going to
receive a fix for the discovered issue"
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: avoid faulting on qemu
Linus Torvalds [Sun, 3 Dec 2017 15:46:16 +0000 (10:46 -0500)]
Merge tag 'hwmon-for-linus-v4.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Fixes:
- Drop reference to obsolete maintainer tree
- Fix overflow bug in pmbus driver
- Fix SMBUS timeout problem in jc42 driver
For the SMBUS timeout handling, we had a brief discussion if this
should be considered a bug fix or a feature. Peter says "it fixes real
problems where the application misbehave due to faulty content when
reading from an eeprom", and he needs the patch in his company's v4.14
images. This is good enough for me and warrants backport to stable
kernels"
* tag 'hwmon-for-linus-v4.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (jc42) optionally try to disable the SMBUS timeout
hwmon: (pmbus) Use 64bit math for DIRECT format values
hwmon: Drop reference to Jean's tree
David Howells [Fri, 1 Dec 2017 11:10:37 +0000 (11:10 +0000)]
rxrpc: Fix the MAINTAINERS record
Fix the MAINTAINERS record so that it's more obvious who the maintainer for
AF_RXRPC is.
Reported-by: Joe Perches <joe@perches.com> Reported-by: David Miller <davem@davemloft.net> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Fri, 1 Dec 2017 11:09:53 +0000 (11:09 +0000)]
rxrpc: Use correct netns source in rxrpc_release_sock()
In rxrpc_release_sock() there may be no rx->local value to access, so we
can't unconditionally follow it to the rxrpc network namespace information
to poke the connection reapers.
Instead, use the socket's namespace pointer to find the namespace.
This unfixed code causes the following static checker warning:
net/rxrpc/af_rxrpc.c:898 rxrpc_release_sock()
error: we previously assumed 'rx->local' could be null (see line 887)
Fixes: 3d18cbb7fd0c ("rxrpc: Fix conn expiry timers") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 3 Dec 2017 14:57:54 +0000 (09:57 -0500)]
Merge tag 'linux-can-fixes-for-4.15-20171201' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2017-12-01
this is a pull for net consisting of nine patches.
The first three patches are by Jimmy Assarsson for the kvaser_usb driver
and add the missing free()s in some error path, a signed/unsigned
comparison and ratelimit the error messages in case of incomplete
messages. Oliver Stäbler's patch for the ti_hecc driver fix the napi
poll function's return value. The return values of the probe function of
the peak_canfd and peak_pci PCI drivers are fixed by Stephane Grosjean's
patch. Two patches by me for the flexcan driver update the
bugs/features/quirks overview table and fix the error state transition
for the VF610 SoC. The two patches by Martin Kelly for the mcba_usb
driver fix a typo and a device disconnect bug.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Wolfram Sang [Sat, 2 Dec 2017 22:32:13 +0000 (23:32 +0100)]
Merge tag 'at24-4.15-fixes-for-wolfram' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into i2c/for-current
Please consider pulling the following fixes for v4.15. While it doesn't
fix any regression introduced in the v4.15 merge window, we have a
feature in at24 since linux v4.8 - reading the mac address block from
at24mac series - which turned out to be not working.
This pull request contains changes that fix it together with a patch
that hardens the read and write argument sanitization with
out-of-bounds checks that were missing.
Lars Persson [Fri, 1 Dec 2017 10:12:44 +0000 (11:12 +0100)]
stmmac: reset last TSO segment size after device open
The mss variable tracks the last max segment size sent to the TSO
engine. We do not update the hardware as long as we receive skb:s with
the same value in gso_size.
During a network device down/up cycle (mapped to stmmac_release() and
stmmac_open() callbacks) we issue a reset to the hardware and it
forgets the setting for mss. However we did not zero out our mss
variable so the next transmission of a gso packet happens with an
undefined hardware setting.
This triggers a hang in the TSO engine and eventuelly the netdev
watchdog will bark.
Fixes: f748be531d70 ("stmmac: support new GMAC4") Signed-off-by: Lars Persson <larper@axis.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Fri, 1 Dec 2017 09:14:51 +0000 (10:14 +0100)]
s390/qeth: build max size GSO skbs on L2 devices
The current GSO skb size limit was copy&pasted over from the L3 path,
where it is needed due to a TSO limitation.
As L2 devices don't offer TSO support (and thus all GSO skbs are
segmented before they reach the driver), there's no reason to restrict
the stack in how large it may build the GSO skbs.
Fixes: d52aec97e5bc ("qeth: enable scatter/gather in layer 2 mode") Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Fri, 1 Dec 2017 09:14:50 +0000 (10:14 +0100)]
s390/qeth: fix GSO throughput regression
Using GSO with small MTUs currently results in a substantial throughput
regression - which is caused by how qeth needs to map non-linear skbs
into its IO buffer elements:
compared to a linear skb, each GSO-segmented skb effectively consumes
twice as many buffer elements (ie two instead of one) due to the
additional header-only part. This causes the Output Queue to be
congested with low-utilized IO buffers.
Fix this as follows:
If the MSS is low enough so that a non-SG GSO segmentation produces
order-0 skbs (currently ~3500 byte), opt out from NETIF_F_SG. This is
where we anticipate the biggest savings, since an SG-enabled
GSO segmentation produces skbs that always consume at least two
buffer elements.
Larger MSS values continue to get a SG-enabled GSO segmentation, since
1) the relative overhead of the additional header-only buffer element
becomes less noticeable, and
2) the linearization overhead increases.
With the throughput regression fixed, re-enable NETIF_F_SG by default to
reap the significant CPU savings of GSO.
Fixes: 5722963a8e83 ("qeth: do not turn on SG per default") Reported-by: Nils Hoppmann <niho@de.ibm.com> Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Fri, 1 Dec 2017 09:14:49 +0000 (10:14 +0100)]
s390/qeth: fix thinko in IPv4 multicast address tracking
Commit 5f78e29ceebf ("qeth: optimize IP handling in rx_mode callback")
reworked how secondary addresses are managed for qeth devices.
Instead of dropping & subsequently re-adding all addresses on every
ndo_set_rx_mode() call, qeth now keeps track of the addresses that are
currently registered with the HW.
On a ndo_set_rx_mode(), we thus only need to do (de-)registration
requests for the addresses that have actually changed.
On L3 devices, the lookup for IPv4 Multicast addresses checks the wrong
hashtable - and thus never finds a match. As a result, we first delete
*all* such addresses, and then re-add them again. So each set_rx_mode()
causes a short period where the IPv4 Multicast addresses are not
registered, and the card stops forwarding inbound traffic for them.
Fix this by setting the ->is_multicast flag on the lookup object, thus
enabling qeth_l3_ip_from_hash() to search the correct hashtable and
find a match there.
Fixes: 5f78e29ceebf ("qeth: optimize IP handling in rx_mode callback") Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 3 Dec 2017 02:31:04 +0000 (21:31 -0500)]
Merge branch 'vhost-skb-leaks'
Wei Xu says:
====================
vhost: fix a few skb leaks
Matthew found a roughly 40% tcp throughput regression with commit c67df11f(vhost_net: try batch dequing from skb array) as discussed
in the following thread:
https://www.mail-archive.com/netdev@vger.kernel.org/msg187936.html
v4:
- fix zero iov iterator count in tap/tap_do_read()(Jason)
- don't put tun in case of EBADFD(Jason)
- Replace msg->msg_control with new 'skb' when calling tun/tap_do_read()
v3:
- move freeing skb from vhost to tun/tap recvmsg() to not
confuse the callers.
v2:
- add Matthew as the reporter, thanks matthew.
- moving zero headcount check ahead instead of defer consuming skb
due to jason and mst's comment.
- add freeing skb in favor of recvmsg() fails.
====================
Acked-by: Michael S. Tsirkin <mst@redhat.com> Tested-by: Matthew Rosato <mjrosato@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Xu [Fri, 1 Dec 2017 10:10:38 +0000 (05:10 -0500)]
tap: free skb if flags error
tap_recvmsg() supports accepting skb by msg_control after
commit 3b4ba04acca8 ("tap: support receiving skb from msg_control"),
the skb if presented should be freed within the function, otherwise
it would be leaked.
Signed-off-by: Wei Xu <wexu@redhat.com> Reported-by: Matthew Rosato <mjrosato@linux.vnet.ibm.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Xu [Fri, 1 Dec 2017 10:10:37 +0000 (05:10 -0500)]
tun: free skb in early errors
tun_recvmsg() supports accepting skb by msg_control after
commit ac77cfd4258f ("tun: support receiving skb through msg_control"),
the skb if presented should be freed no matter how far it can go
along, otherwise it would be leaked.
This patch fixes several missed cases.
Signed-off-by: Wei Xu <wexu@redhat.com> Reported-by: Matthew Rosato <mjrosato@linux.vnet.ibm.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Xu [Fri, 1 Dec 2017 10:10:36 +0000 (05:10 -0500)]
vhost: fix skb leak in handle_rx()
Matthew found a roughly 40% tcp throughput regression with commit c67df11f(vhost_net: try batch dequing from skb array) as discussed
in the following thread:
https://www.mail-archive.com/netdev@vger.kernel.org/msg187936.html
Eventually we figured out that it was a skb leak in handle_rx()
when sending packets to the VM. This usually happens when a guest
can not drain out vq as fast as vhost fills in, afterwards it sets
off the traffic jam and leaks skb(s) which occurs as no headcount
to send on the vq from vhost side.
This can be avoided by making sure we have got enough headcount
before actually consuming a skb from the batched rx array while
transmitting, which is simply done by moving checking the zero
headcount a bit ahead.
Signed-off-by: Wei Xu <wexu@redhat.com> Reported-by: Matthew Rosato <mjrosato@linux.vnet.ibm.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 3 Dec 2017 02:25:39 +0000 (21:25 -0500)]
Merge branch 'bnxt_en-fixes'
Michael Chan says:
====================
bnxt_en: Fixes.
A shutdown fix for SMARTNIC, 2 fixes related to TC Flower vxlan
filters, and the last one fixes an out-of-scope variable when sending
short firmware messages.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_en: Fix a variable scoping in bnxt_hwrm_do_send_msg()
short_input variable is assigned to another data pointer which is
referred out of its scope. Fix it by moving short_input definition
to the beginning of bnxt_hwrm_do_send_msg() function.
No failure has been reported so far due to this issue.
Fixes: e605db801bde ("bnxt_en: Support for Short Firmware Message") Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sathya Perla [Fri, 1 Dec 2017 08:13:04 +0000 (03:13 -0500)]
bnxt_en: fix dst/src fid for vxlan encap/decap actions
For flows that involve a vxlan encap action, the vxlan sock
interface may be specified as the outgoing interface. The driver
must resolve the outgoing PF interface used by this socket and
use the dst_fid of the PF in the hwrm_cfa_encap_record_alloc cmd.
Similarily for flows that have a vxlan decap action, the
fid of the incoming PF interface must be used as the src_fid in
the hwrm_cfa_decap_filter_alloc cmd.
Fixes: 8c95f773b4a3 ("bnxt_en: add support for Flower based vxlan encap/decap offload") Signed-off-by: Sathya Perla <sathya.perla@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sunil Challa [Fri, 1 Dec 2017 08:13:03 +0000 (03:13 -0500)]
bnxt_en: wildcard smac while creating tunnel decap filter
While creating a decap filter the tunnel smac need not (and must not) be
specified as we cannot ascertain the neighbor in the recv path. 'ttl'
match is also not needed for the decap filter and must be wild-carded.
Fixes: f484f6782e01 ("bnxt_en: add hwrm FW cmds for cfa_encap_record and decap_filter") Signed-off-by: Sunil Challa <sunilkumar.challa@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ray Jui [Fri, 1 Dec 2017 08:13:02 +0000 (03:13 -0500)]
bnxt_en: Need to unconditionally shut down RoCE in bnxt_shutdown
The current 'bnxt_shutdown' implementation only invokes
'bnxt_ulp_shutdown' to shut down RoCE in the case when the system is in
the path of power off (SYSTEM_POWER_OFF). While this may work in most
cases, it does not work in the smart NIC case, when Linux 'reboot'
command is initiated from the Linux that runs on the ARM cores of the
NIC card. In this particular case, Linux 'reboot' results in a system
'L3' level reset where the entire ARM and associated subsystems are
being reset, but at the same time, Nitro core is being kept in sane state
(to allow external PCIe connected servers to continue to work). Without
properly shutting down RoCE and freeing all associated resources, it
results in the ARM core to hang immediately after the 'reboot'
By always invoking 'bnxt_ulp_shutdown' in 'bnxt_shutdown', it fixes the
above issue
Fixes: 0efd2fc65c92 ("bnxt_en: Add a callback to inform RDMA driver during PCI shutdown.") Signed-off-by: Ray Jui <ray.jui@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 2 Dec 2017 01:04:20 +0000 (20:04 -0500)]
Merge tag 'nfs-for-4.15-2' of git://git.linux-nfs.org/projects/anna/linux-nfs
Pull NFS client fixes from Anna Schumaker:
"These patches fix a problem with compiling using an old version of
gcc, and also fix up error handling in the SUNRPC layer.
- NFSv4: Ensure gcc 4.4.4 can compile initialiser for
"invalid_stateid"
- SUNRPC: Allow connect to return EHOSTUNREACH
- SUNRPC: Handle ENETDOWN errors"
* tag 'nfs-for-4.15-2' of git://git.linux-nfs.org/projects/anna/linux-nfs:
SUNRPC: Handle ENETDOWN errors
SUNRPC: Allow connect to return EHOSTUNREACH
NFSv4: Ensure gcc 4.4.4 can compile initialiser for "invalid_stateid"
Linus Torvalds [Sat, 2 Dec 2017 01:00:19 +0000 (20:00 -0500)]
Merge tag 'xfs-4.15-fixes-4' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fixes from Darrick Wong:
"Here are some bug fixes for 4.15-rc2.
- fix memory leaks that appeared after removing ifork inline data
buffer
- recover deferred rmap update log items in correct order
- fix memory leaks when buffer construction fails
- fix memory leaks when bmbt is corrupt
- fix some uninitialized variables and math problems in the quota
scrubber
- add some omitted attribution tags on the log replay commit
- fix some UBSAN complaints about integer overflows with large sparse
files
- implement an effective inode mode check in online fsck
- fix log's inability to retry quota item writeout due to transient
errors"
* tag 'xfs-4.15-fixes-4' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: Properly retry failed dquot items in case of error during buffer writeback
xfs: scrub inode mode properly
xfs: remove unused parameter from xfs_writepage_map
xfs: ubsan fixes
xfs: calculate correct offset in xfs_scrub_quota_item
xfs: fix uninitialized variable in xfs_scrub_quota
xfs: fix leaks on corruption errors in xfs_bmap.c
xfs: fortify xfs_alloc_buftarg error handling
xfs: log recovery should replay deferred ops in order
xfs: always free inline data before resetting inode fork during ifree
Linus Torvalds [Sat, 2 Dec 2017 00:39:12 +0000 (19:39 -0500)]
Merge tag 'riscv-for-linus-4.15-rc2_cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/linux
Pull RISC-V cleanups and ABI fixes from Palmer Dabbelt:
"This contains a handful of small cleanups that are a result of
feedback that didn't make it into our original patch set, either
because the feedback hadn't been given yet, I missed the original
emails, or we weren't ready to submit the changes yet.
I've been maintaining the various cleanup patch sets I have as their
own branches, which I then merged together and signed. Each merge
commit has a short summary of the changes, and each branch is based on
your latest tag (4.15-rc1, in this case). If this isn't the right way
to do this then feel free to suggest something else, but it seems sane
to me.
Here's a short summary of the changes, roughly in order of how
interesting they are.
- libgcc.h has been moved from include/lib, where it's the only
member, to include/linux. This is meant to avoid tab completion
conflicts.
- VDSO entries for clock_get/gettimeofday/getcpu have been added.
These are simple syscalls now, but we want to let glibc use them
from the start so we can make them faster later.
- A VDSO entry for instruction cache flushing has been added so
userspace can flush the instruction cache.
- The VDSO symbol versions for __vdso_cmpxchg{32,64} have been
removed, as those VDSO entries don't actually exist.
- __io_writes has been corrected to respect the given type.
- A new READ_ONCE in arch_spin_is_locked().
- __test_and_op_bit_ord() is now actually ordered.
- Various small fixes throughout the tree to enable allmodconfig to
build cleanly.
- Removal of some dead code in our atomic support headers.
- Improvements to various comments in our atomic support headers"
* tag 'riscv-for-linus-4.15-rc2_cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/linux: (23 commits)
RISC-V: __io_writes should respect the length argument
move libgcc.h to include/linux
RISC-V: Clean up an unused include
RISC-V: Allow userspace to flush the instruction cache
RISC-V: Flush I$ when making a dirty page executable
RISC-V: Add missing include
RISC-V: Use define for get_cycles like other architectures
RISC-V: Provide stub of setup_profiling_timer()
RISC-V: Export some expected symbols for modules
RISC-V: move empty_zero_page definition to C and export it
RISC-V: io.h: type fixes for warnings
RISC-V: use RISCV_{INT,SHORT} instead of {INT,SHORT} for asm macros
RISC-V: use generic serial.h
RISC-V: remove spin_unlock_wait()
RISC-V: `sfence.vma` orderes the instruction cache
RISC-V: Add READ_ONCE in arch_spin_is_locked()
RISC-V: __test_and_op_bit_ord should be strongly ordered
RISC-V: Remove smb_mb__{before,after}_spinlock()
RISC-V: Remove __smp_bp__{before,after}_atomic
RISC-V: Comment on why {,cmp}xchg is ordered how it is
...
Linus Torvalds [Sat, 2 Dec 2017 00:37:03 +0000 (19:37 -0500)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"The critical one here is a fix for fpsimd register corruption across
signals which was introduced by the SVE support code (the register
files overlap), but the others are worth having as well.
Summary:
- Fix FP register corruption when SVE is not available or in use
- Fix out-of-tree module build failure when CONFIG_ARM64_MODULE_PLTS=y
- Missing 'const' generating errors with LTO builds
- Remove unsupported events from Cortex-A73 PMU description
- Removal of stale and incorrect comments"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: context: Fix comments and remove pointless smp_wmb()
arm64: cpu_ops: Add missing 'const' qualifiers
arm64: perf: remove unsupported events for Cortex-A73
arm64: fpsimd: Fix failure to restore FPSIMD state after signals
arm64: pgd: Mark pgd_cache as __ro_after_init
arm64: ftrace: emit ftrace-mod.o contents through code
arm64: module-plts: factor out PLT generation code for ftrace
arm64: mm: cleanup stale AIVIVT references
Palmer Dabbelt [Fri, 1 Dec 2017 21:31:31 +0000 (13:31 -0800)]
RISC-V: Fixes for clean allmodconfig build
Olaf said: Here's a short series of patches that produces a working
allmodconfig. Would be nice to see them go in so we can add build
coverage.
I've dropped patches 8 and 10 from the original set:
* [PATCH 08/10] (RISC-V: Set __ARCH_WANT_RENAMEAT to pick up generic
version) has a better fix that I've sent out for review, we don't want
renameat.
* [PATCH 10/10] (input: joystick: riscv has get_cycles) has already been
taken into Dmitry Torokhov's tree.
Palmer Dabbelt [Fri, 1 Dec 2017 21:12:10 +0000 (13:12 -0800)]
RISC-V: User-Visible Changes
This merge contains the user-visible, ABI-breaking changes that we want
to make sure we have in Linux before our first release. Highlights
include:
* VDSO entries for clock_get/gettimeofday/getcpu have been added. These
are simple syscalls now, but we want to let glibc use them from the
start so we can make them faster later.
* A VDSO entry for instruction cache flushing has been added so
userspace can flush the instruction cache.
* The VDSO symbol versions for __vdso_cmpxchg{32,64} have been removed,
as those VDSO entries don't actually exist.
Palmer Dabbelt [Fri, 1 Dec 2017 21:10:42 +0000 (13:10 -0800)]
RISC-V Atomic Cleanups
This patch set is the result of some feedback that filtered through
after our original patch set was reviewed, some of which was the result
of me missing some email. It contains:
* A new READ_ONCE in arch_spin_is_locked()
* __test_and_op_bit_ord() is now actually ordered
* Improvements to various comments
* Removal of some dead code
David S. Miller [Fri, 1 Dec 2017 20:18:42 +0000 (15:18 -0500)]
Merge branch 'sfp-phylink-fixes'
Russell King says:
====================
SFP/phylink fixes
Here are four phylink fixes:
- the "options" is a big-endian value, we must test the bits taking the
endian-ness into account.
- improve the handling of RX_LOS polarity, taking no RX_LOS polarity
bits set to mean there is no RX_LOS functionality provided.
- do not report modules that require the address mode switching as
supporting SFF8472.
- ensure that the mac_link_down() function is called when phylink_stop()
is called.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Thu, 30 Nov 2017 13:59:26 +0000 (13:59 +0000)]
phylink: ensure we take the link down when phylink_stop() is called
Ensure that we tell the MAC to take the link down when phylink_stop()
is called, and that this completes prior to phylink_stop() returns.
Reported-by: Florian Fainelli <f.fainelli@gmail.com> Tested-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Thu, 30 Nov 2017 13:59:21 +0000 (13:59 +0000)]
sfp: warn about modules requiring address change sequence
We do not support SFP modules which require the address change sequence
as detailed by SFF 8472 revision 1.22 section 8.9. Warn when these
modules are inserted, and treat them as SFF8079 modules for ethtool.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Thu, 30 Nov 2017 13:59:16 +0000 (13:59 +0000)]
sfp: improve RX_LOS handling
There are two bits in the option word for the RX_LOS signal. One
reports that the RX_LOS signal is active high, the other reports that
it is active low. When both or neither are set, the result is not
well defined in the specification.
Rather than assuming that neither set means normal RX_LOS, take this
as meaning no RX_LOS signal available, thereby ignoring the signal.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Thu, 30 Nov 2017 13:59:11 +0000 (13:59 +0000)]
sfp: fix RX_LOS signal handling
The options word is a be16 quantity, so we need to test the flags
having converted the endian-ness. Convert the flag bits to be16,
which can be optimised by the compiler, rather than converting a
variable at runtime.
Reported-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Tommi Rantala [Wed, 29 Nov 2017 10:48:42 +0000 (12:48 +0200)]
tipc: call tipc_rcv() only if bearer is up in tipc_udp_recv()
Remove the second tipc_rcv() call in tipc_udp_recv(). We have just
checked that the bearer is not up, and calling tipc_rcv() with a bearer
that is not up leads to a TIPC div-by-zero crash in
tipc_node_calculate_timer(). The crash is rare in practice, but can
happen like this:
We're enabling a bearer, but it's not yet up and fully initialized.
At the same time we receive a discovery packet, and in tipc_udp_recv()
we end up calling tipc_rcv() with the not-yet-initialized bearer,
causing later the div-by-zero crash in tipc_node_calculate_timer().
Jon Maloy explains the impact of removing the second tipc_rcv() call:
"link setup in the worst case will be delayed until the next arriving
discovery messages, 1 sec later, and this is an acceptable delay."
As the tipc_rcv() call is removed, just leave the function via the
rcu_out label, so that we will kfree_skb().
Fixes: c9b64d492b1f ("tipc: add replicast peer discovery") Signed-off-by: Tommi Rantala <tommi.t.rantala@nokia.com> Cc: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 1 Dec 2017 18:06:56 +0000 (10:06 -0800)]
tcp/dccp: block bh before arming time_wait timer
Maciej Żenczykowski reported some panics in tcp_twsk_destructor()
that might be caused by the following bug.
timewait timer is pinned to the cpu, because we want to transition
timwewait refcount from 0 to 4 in one go, once everything has been
initialized.
At the time commit ed2e92394589 ("tcp/dccp: fix timewait races in timer
handling") was merged, TCP was always running from BH habdler.
After commit 5413d1babe8f ("net: do not block BH while processing
socket backlog") we definitely can run tcp_time_wait() from process
context.
We need to block BH in the critical section so that the pinned timer
has still its purpose.
This bug is more likely to happen under stress and when very small RTO
are used in datacenter flows.
Fixes: 5413d1babe8f ("net: do not block BH while processing socket backlog") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Maciej Żenczykowski <maze@google.com> Acked-by: Maciej Żenczykowski <maze@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 1 Dec 2017 20:06:31 +0000 (15:06 -0500)]
Merge branch 'sctp-prsctp-chunk-fixes'
Xin Long says:
====================
sctp: a couple of fixes for chunks abandoned in prsctp
Now when abandoning chunks in prsctp, it doesn't consider for frags in
one msg, which would cause peer can never receive the whole frags for
one msg to get them reassembled, these pieces of this msg will stay in
the reasm queue forever and block the following chunks' receiving.
This patchset is to fix them in patch 2 and 3, and also fix another
issue for prsctp in patch 1.
====================
Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Sat, 25 Nov 2017 13:18:36 +0000 (21:18 +0800)]
sctp: do not abandon the other frags in unsent outq if one msg has outstanding frags
Now for the abandoned chunks in unsent outq, it would just free the chunks.
Because no tsn is assigned to them yet, there's no need to send fwd tsn to
peer, unlike for the abandoned chunks in sent outq.
The problem is when parts of the msg have been sent and the other frags
are still in unsent outq, if they are abandoned/dropped, the peer would
never get this msg reassembled.
So these frags in unsent outq can't be dropped if this msg already has
outstanding frags.
This patch does the check in sctp_chunk_abandoned and
sctp_prsctp_prune_unsent.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Sat, 25 Nov 2017 13:18:35 +0000 (21:18 +0800)]
sctp: abandon the whole msg if one part of a fragmented message is abandoned
As rfc3758#section-3.1 demands:
A3) When a TSN is "abandoned", if it is part of a fragmented message,
all other TSN's within that fragmented message MUST be abandoned
at the same time.
Besides, if it couldn't handle this, the rest frags would never get
assembled in peer side.
This patch supports it by adding abandoned flag in sctp_datamsg, when
one chunk is being abandoned, set chunk->msg->abandoned as well. Next
time when checking for abandoned, go checking chunk->msg->abandoned
first.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Sat, 25 Nov 2017 13:18:34 +0000 (21:18 +0800)]
sctp: only update outstanding_bytes for transmitted queue when doing prsctp_prune
Now outstanding_bytes is only increased when appending chunks into one
packet and sending it at 1st time, while decreased when it is about to
move into retransmit queue. It means outstanding_bytes value is already
decreased for all chunks in retransmit queue.
However sctp_prsctp_prune_sent is a common function to check the chunks
in both transmitted and retransmit queue, it decrease outstanding_bytes
when moving a chunk into abandoned queue from either of them.
It could cause outstanding_bytes underflow, as it also decreases it's
value for the chunks in retransmit queue.
This patch fixes it by only updating outstanding_bytes for transmitted
queue when pruning queues for prsctp prio policy, the same fix is also
needed in sctp_check_transmitted.
Fixes: 8dbdf1f5b09c ("sctp: implement prsctp PRIO policy") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jan Stancek [Fri, 1 Dec 2017 09:50:28 +0000 (10:50 +0100)]
virtio_balloon: fix increment of vb->num_pfns in fill_balloon()
commit c7cdff0e8647 ("virtio_balloon: fix deadlock on OOM")
changed code to increment vb->num_pfns before call to
set_page_pfns(), which used to happen only after.
This patch fixes boot hang for me on ppc64le KVM guests.
Fixes: c7cdff0e8647 ("virtio_balloon: fix deadlock on OOM") Cc: Michael S. Tsirkin <mst@redhat.com> Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Cc: Michal Hocko <mhocko@suse.com> Cc: Wei Wang <wei.w.wang@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Jan Stancek <jstancek@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
On driver remove(), all objects created during probe() should be
removed, but sysfs qemu_fw_cfg/rev file was left. Also reorder
functions to match probe() error cleanup code.
Cc: stable@vger.kernel.org Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Linus Torvalds [Fri, 1 Dec 2017 13:40:17 +0000 (08:40 -0500)]
Merge tag 'powerpc-4.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Two fixes for nasty kexec/kdump crashes in certain configurations.
A couple of minor fixes for the new TIDR code.
A fix for an oops in a CXL error handling path.
Thanks to: Andrew Donnellan, Christophe Lombard, David Gibson, Mahesh
Salgaonkar, Vaibhav Jain"
* tag 'powerpc-4.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc: Do not assign thread.tidr if already assigned
powerpc: Avoid signed to unsigned conversion in set_thread_tidr()
powerpc/kexec: Fix kexec/kdump in P9 guest kernels
powerpc/powernv: Fix kexec crashes caused by tlbie tracing
cxl: Check if vphb exists before iterating over AFU devices
Linus Torvalds [Fri, 1 Dec 2017 13:14:22 +0000 (08:14 -0500)]
Merge tag 'mmc-v4.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"MMC core:
- Ensure that debugfs files are removed properly
- Fix missing blk_put_request()
- Deal with errors from blk_get_request()
- Rewind mmc bus suspend operations at failures
- Prepend '0x' to ocr and pre_eol_info in sysfs to identify as hex
MMC host:
- sdhci-msm: Make it optional to wait for signal level changes
- sdhci: Avoid swiotlb buffer being full"
* tag 'mmc-v4.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: core: prepend 0x to OCR entry in sysfs
mmc: core: prepend 0x to pre_eol_info entry in sysfs
mmc: sdhci: Avoid swiotlb buffer being full
mmc: sdhci-msm: Optionally wait for signal level changes
mmc: block: Ensure that debugfs files are removed
mmc: core: Do not leave the block driver in a suspended state
mmc: block: Check return value of blk_get_request()
mmc: block: Fix missing blk_put_request()
amdgpu:
- New display code (dc) dpms, suspend/resume and smatch fixes, along
with some others
- Some regression fixes for amdkfd/radeon.
- Fix a ttm regression for swiotlb disabled
bridge:
- A bunch of fixes for the tc358767 bridge
mali-dp + hdlcd:
- some fixes and internal API catchups.
imx-drm:
-regression fix in atomic code.
omapdrm:
- platform detection regression fixes"
* tag 'drm-fixes-for-v4.15-rc2' of git://people.freedesktop.org/~airlied/linux: (76 commits)
drm/imx: always call wait_for_flip_done in commit_tail
omapdrm: hdmi4_cec: signedness bug in hdmi4_cec_init()
drm: omapdrm: Fix DPI on platforms using the DSI VDDS
omapdrm: hdmi4: Correct the SoC revision matching
drm/omap: displays: panel-dpi: add backlight dependency
drm/omap: Fix error handling path in 'omap_dmm_probe()'
drm/i915: Disable THP until we have a GPU read BW W/A
drm/bridge: tc358767: fix 1-lane behavior
drm/bridge: tc358767: fix AUXDATAn registers access
drm/bridge: tc358767: fix timing calculations
drm/bridge: tc358767: fix DP0_MISC register set
drm/bridge: tc358767: filter out too high modes
drm/bridge: tc358767: do no fail on hi-res displays
drm/bridge: Fix lvds-encoder since the panel_bridge rework.
drm/bridge: synopsys/dw-hdmi: Enable cec clock
drm/bridge: adv7511/33: Fix adv7511_cec_init() failure handling
drm/radeon: remove init of CIK VMIDs 8-16 for amdkfd
drm/ttm: fix populate_and_map() functions once more
drm/fb_helper: Disable all crtc's when initial setup fails.
drm/atomic: make drm_atomic_helper_wait_for_vblanks more agressive
...
Linus Torvalds [Fri, 1 Dec 2017 13:05:45 +0000 (08:05 -0500)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A selection of fixes/changes that should make it into this series.
This contains:
- NVMe, two merges, containing:
- pci-e, rdma, and fc fixes
- Device quirks
- Fix for a badblocks leak in null_blk
- bcache fix from Rui Hua for a race condition regression where
-EINTR was returned to upper layers that didn't expect it.
- Regression fix for blktrace for a bug introduced in this series.
- blktrace cleanup for cgroup id.
- bdi registration error handling.
- Small series with cleanups for blk-wbt.
- Various little fixes for typos and the like.
Nothing earth shattering, most important are the NVMe and bcache fixes"
* 'for-linus' of git://git.kernel.dk/linux-block: (34 commits)
nvme-pci: fix NULL pointer dereference in nvme_free_host_mem()
nvme-rdma: fix memory leak during queue allocation
blktrace: fix trace mutex deadlock
nvme-rdma: Use mr pool
nvme-rdma: Check remotely invalidated rkey matches our expected rkey
nvme-rdma: wait for local invalidation before completing a request
nvme-rdma: don't complete requests before a send work request has completed
nvme-rdma: don't suppress send completions
bcache: check return value of register_shrinker
bcache: recover data from backing when data is clean
bcache: Fix building error on MIPS
bcache: add a comment in journal bucket reading
nvme-fc: don't use bit masks for set/test_bit() numbers
blk-wbt: fix comments typo
blk-wbt: move wbt_clear_stat to common place in wbt_done
blk-sysfs: remove NULL pointer checking in queue_wb_lat_store
blk-wbt: remove duplicated setting in wbt_init
nvme-pci: add quirk for delay before CHK RDY for WDC SN200
block: remove useless assignment in bio_split
null_blk: fix dev->badblocks leak
...
Will Deacon [Thu, 30 Nov 2017 18:25:17 +0000 (18:25 +0000)]
arm64: context: Fix comments and remove pointless smp_wmb()
The comments in the ASID allocator incorrectly hint at an MP-style idiom
using the asid_generation and the active_asids array. In fact, the
synchronisation is achieved using a combination of an xchg operation
and a spinlock, so update the comments and remove the pointless smp_wmb().
Cc: James Morse <james.morse@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
Dave Martin [Thu, 30 Nov 2017 11:56:37 +0000 (11:56 +0000)]
arm64: fpsimd: Fix failure to restore FPSIMD state after signals
The fpsimd_update_current_state() function is responsible for
loading the FPSIMD state from the user signal frame into the
current task during sigreturn. When implementing support for SVE,
conditional code was added to this function in order to handle the
case where SVE state need to be loaded for the task and merged with
the FPSIMD data from the signal frame; however, the FPSIMD-only
case was unintentionally dropped.
As a result of this, sigreturn does not currently restore the
FPSIMD state of the task, except in the case where the system
supports SVE and the signal frame contains SVE state in addition to
FPSIMD state.
This patch fixes this bug by making the copy-in of the FPSIMD data
from the signal frame to thread_struct unconditional.
This remains a performance regression from v4.14, since the FPSIMD
state is now copied into thread_struct and then loaded back,
instead of _only_ being loaded into the CPU FPSIMD registers.
However, it is essential to call task_fpsimd_load() here anyway in
order to ensure that the SVE enable bit in CPACR_EL1 is set
correctly before returning to userspace. This could use some
refactoring, but since sigreturn is not a fast path I have kept
this patch as a pure fix and left the refactoring for later.
Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org> Fixes: 8cd969d28fd2 ("arm64/sve: Signal handling support") Reported-by: Alex Bennée <alex.bennee@linaro.org> Tested-by: Alex Bennée <alex.bennee@linaro.org> Reviewed-by: Alex Bennée <alex.bennee@linaro.org> Signed-off-by: Dave Martin <Dave.Martin@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
Ard Biesheuvel [Mon, 20 Nov 2017 17:41:30 +0000 (17:41 +0000)]
arm64: ftrace: emit ftrace-mod.o contents through code
When building the arm64 kernel with both CONFIG_ARM64_MODULE_PLTS and
CONFIG_DYNAMIC_FTRACE enabled, the ftrace-mod.o object file is built
with the kernel and contains a trampoline that is linked into each
module, so that modules can be loaded far away from the kernel and
still reach the ftrace entry point in the core kernel with an ordinary
relative branch, as is emitted by the compiler instrumentation code
dynamic ftrace relies on.
In order to be able to build out of tree modules, this object file
needs to be included into the linux-headers or linux-devel packages,
which is undesirable, as it makes arm64 a special case (although a
precedent does exist for 32-bit PPC).
Given that the trampoline essentially consists of a PLT entry, let's
not bother with a source or object file for it, and simply patch it
in whenever the trampoline is being populated, using the existing
PLT support routines.
Cc: <stable@vger.kernel.org> Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Will Deacon <will.deacon@arm.com>
David Howells [Fri, 1 Dec 2017 11:40:43 +0000 (11:40 +0000)]
afs: Properly reset afs_vnode (inode) fields
When an AFS inode is allocated by afs_alloc_inode(), the allocated
afs_vnode struct isn't necessarily reset from the last time it was used as
an inode because the slab constructor is only invoked once when the memory
is obtained from the page allocator.
This means that information can leak from one inode to the next because
we're not calling kmem_cache_zalloc(). Some of the information isn't
reset, in particular the permit cache pointer.
Bring the clearances up to date.
Signed-off-by: David Howells <dhowells@redhat.com> Tested-by: Marc Dionne <marc.dionne@auristor.com>
David Howells [Fri, 1 Dec 2017 11:40:43 +0000 (11:40 +0000)]
afs: Fix permit refcounting
Fix four refcount bugs in afs_cache_permit():
(1) When checking the result of the kzalloc(), we can't just return, but
must put 'permits'.
(2) We shouldn't put permits immediately after hashing a new permit as we
need to keep the pointer stable so that we can check to see if
vnode->permit_cache has changed before we decide whether to assign to
it.
(3) 'permits' is being put twice.
(4) We need to put either the replacement or the thing replaced after the
assignment to vnode->permit_cache.
Without this, lots of the following are seen:
Kernel BUG at ffffffffa039857b [verbose debug info unavailable]
------------[ cut here ]------------
Kernel BUG at ffffffffa039858a [verbose debug info unavailable]
------------[ cut here ]------------
The addresses are in the .text..refcount section of the kafs.ko module.
Following the relocation records for the __ex_table section shows one to be
due to the decrement in afs_put_permits() and the other to be key_get() in
afs_cache_permit().
Occasionally, the following is seen:
refcount_t overflow at afs_cache_permit+0x57d/0x5c0 [kafs] in cc1[562], uid/euid: 0/0
WARNING: CPU: 0 PID: 562 at kernel/panic.c:657 refcount_error_report+0x9c/0xac
...
Reported-by: Marc Dionne <marc.dionne@auristor.com> Signed-off-by: David Howells <dhowells@redhat.com> Tested-by: Marc Dionne <marc.dionne@auristor.com>
can: peak/pci: fix potential bug when probe() fails
PCI/PCIe drivers for PEAK-System CAN/CAN-FD interfaces do some access to the
PCI config during probing. In case one of these accesses fails, a POSITIVE
PCIBIOS_xxx error code is returned back. This POSITIVE error code MUST be
converted into a NEGATIVE errno for the probe() function to indicate it
failed. Using the pcibios_err_to_errno() function, we make sure that the
return code will always be negative.
Oliver Stäbler [Mon, 20 Nov 2017 13:45:15 +0000 (14:45 +0100)]
can: ti_hecc: Fix napi poll return value for repoll
After commit d75b1ade567f ("net: less interrupt masking in NAPI") napi
repoll is done only when work_done == budget.
So we need to return budget if there are still packets to receive.
Signed-off-by: Oliver Stäbler <oliver.staebler@bytesatwork.ch> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Jimmy Assarsson [Tue, 21 Nov 2017 07:22:27 +0000 (08:22 +0100)]
can: kvaser_usb: Fix comparison bug in kvaser_usb_read_bulk_callback()
The conditon in the while-loop becomes true when actual_length is less than
2 (MSG_HEADER_LEN). In best case we end up with a former, already
dispatched msg, that got msg->len greater than actual_length. This will
result in a "Format error" error printout.
Problem seen when unplugging a Kvaser USB device connected to a vbox guest.
warning: comparison between signed and unsigned integer expressions
[-Wsign-compare]
Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Yonghong Song [Thu, 30 Nov 2017 21:47:55 +0000 (13:47 -0800)]
samples/bpf: add error checking for perf ioctl calls in bpf loader
load_bpf_file() should fail if ioctl with command
PERF_EVENT_IOC_ENABLE and PERF_EVENT_IOC_SET_BPF fails.
When they do fail, proper error messages are printed.
With this change, the below "syscall_tp" run shows that
the maximum number of bpf progs attaching to the same
perf tracepoint is indeed enforced.
$ ./syscall_tp -i 64
prog #0: map ids 4 5
...
prog #63: map ids 382 383
$ ./syscall_tp -i 65
prog #0: map ids 4 5
...
prog #64: map ids 388 389
ioctl PERF_EVENT_IOC_SET_BPF failed err Argument list too long
Signed-off-by: Yonghong Song <yhs@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Yonghong Song [Thu, 30 Nov 2017 21:47:54 +0000 (13:47 -0800)]
bpf: set maximum number of attached progs to 64 for a single perf tp
cgropu+bpf prog array has a maximum number of 64 programs.
Let us apply the same limit here.
Fixes: e87c6bc3852b ("bpf: permit multiple bpf attachments for a single perf event") Signed-off-by: Yonghong Song <yhs@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Linus Torvalds [Thu, 30 Nov 2017 23:49:50 +0000 (18:49 -0500)]
Merge tag 'acpi-4.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These fix a regression related to the ACPI EC handling during system
suspend/resume on some platforms and prevent modalias from being
exposed to user space for ACPI device object with "not functional and
not present" status.
Specifics:
- Fix an ACPI EC driver regression (from the 4.9 cycle) causing the
driver's power management operations to be omitted during system
suspend/resume on platforms where the EC instance from the ECDT
table is used instead of the one from the DSDT (Lv Zheng).
- Prevent modalias from being exposed to user space for ACPI device
objects with _STA returning 0 (not present and not functional) to
prevent driver modules from being loaded automatically for hardware
that is not actually present on some platforms (Hans de Goede)"
* tag 'acpi-4.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / EC: Fix regression related to PM ops support in ECDT device
ACPI / bus: Leave modalias empty for devices which are not present
Dave Airlie [Thu, 30 Nov 2017 23:15:57 +0000 (09:15 +1000)]
Merge branch 'drm-fixes-4.15' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Fixes for 4.15. Highlights:
- DC fixes for S3, gamma, audio, pageflipping, etc.
- fix a regression in radeon from kfd removal
- fix a ttm regression with swiotlb disabled
- misc other fixes
* 'drm-fixes-4.15' of git://people.freedesktop.org/~agd5f/linux: (36 commits)
drm/radeon: remove init of CIK VMIDs 8-16 for amdkfd
drm/ttm: fix populate_and_map() functions once more
drm/amd/display: USB-C / thunderbolt dock specific workaround
drm/amd/display: Switch to drm_atomic_helper_wait_for_flip_done
drm/amd/display: fix gamma setting
drm/amd/display: Do not put drm_atomic_state on resume
drm/amd/display: Fix couple more inconsistent NULL checks in dc_resource
drm/amd/display: Fix potential NULL and mem leak in create_links
drm/amd/display: Fix hubp check in set_cursor_position
drm/amd/display: Fix use before NULL check in validate_timing
drm/amd/display: Bunch of smatch error and warning fixes in DC
drm/amd/display: Fix amdgpu_dm bugs found by smatch
drm/amd/display: try to find matching audio inst for enc inst first
drm/amd/display: fix seq issue: turn on clock before programming afmt.
drm/amd/display: fix memory leaks on error exit return
drm/amd/display: check plane state before validating fbc
drm/amd/display: Do DC mode-change check when adding CRTCs
drm/amd/display: Revert noisy assert messages
drm/amd/display: fix split viewport rounding error
drm/amd/display: Check aux channel before MST resume
...
Dave Airlie [Thu, 30 Nov 2017 23:15:31 +0000 (09:15 +1000)]
Merge branch 'for-upstream/mali-dp' of git://linux-arm.org/linux-ld into drm-fixes
mali-dp interface cleanups.
* 'for-upstream/mali-dp' of git://linux-arm.org/linux-ld:
drm: mali-dp: Disable planes when their CRTC gets disabled.
drm: mali-dp: Separate static internal data into a read-only structure.
drm/arm: Replace instances of drm_dev_unref with drm_dev_put.
drm: mali-dp: switch to drm_*_get(), drm_*_put() helpers
Dave Airlie [Thu, 30 Nov 2017 23:14:46 +0000 (09:14 +1000)]
Merge tag 'drm-amdkfd-fixes-2017-11-26' of git://people.freedesktop.org/~gabbayo/linux into drm-fixes
This is amdkfd pull request for -rc2. It contains three small fixes to the
CIK SDMA code, compilation error fix in kfd_ioctl.h and fix to accessing
a pointer after it was released.
* tag 'drm-amdkfd-fixes-2017-11-26' of git://people.freedesktop.org/~gabbayo/linux:
uapi: fix linux/kfd_ioctl.h userspace compilation errors
drm/amdkfd: fix amdkfd use-after-free GP fault
drm/amdkfd: Fix SDMA oversubsription handling
drm/amdkfd: Fix SDMA ring buffer size calculation
drm/amdgpu: Fix SDMA load/unload sequence on HWS disabled mode
Dave Airlie [Thu, 30 Nov 2017 23:14:18 +0000 (09:14 +1000)]
Merge branch 'for-upstream/hdlcd' of git://linux-arm.org/linux-ld into drm-fixes
3 hdlcd fixes/cleanups
* 'for-upstream/hdlcd' of git://linux-arm.org/linux-ld:
drm/arm: Replace instances of drm_dev_unref with drm_dev_put.
drm: Fix checkpatch issue: "WARNING: braces {} are not necessary for single statement blocks."
drm: hdlcd: Update PM code to save/restore console.
Dave Airlie [Thu, 30 Nov 2017 23:11:13 +0000 (09:11 +1000)]
Merge tag 'imx-drm-fixes-2017-11-30' of git://git.pengutronix.de/git/pza/linux into drm-fixes
drm/imx: fix commit_tail for new drm_atomic_helper_setup_commit
Since commit 080de2e5be2d ("drm/atomic: Check for busy planes/connectors before
setting the commit"), drm_atomic_helper_setup_commit expects that blocking
commits have completed flipping before the commit_tail returns. Add the missing
wait_for_flip_done to commit_tail to ensure this.
* tag 'imx-drm-fixes-2017-11-30' of git://git.pengutronix.de/git/pza/linux:
drm/imx: always call wait_for_flip_done in commit_tail
Dave Airlie [Thu, 30 Nov 2017 23:10:32 +0000 (09:10 +1000)]
Merge tag 'drm-intel-fixes-2017-11-30' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- Disable transparent huge pages for now until we have a W/A
- Building fix when CONFIG_BACKLIGHT_CLASS_DEVICE is not selected
- GMBUS communication robustness
- Fbdev hotplug handling fix
* tag 'drm-intel-fixes-2017-11-30' of git://anongit.freedesktop.org/drm/drm-intel:
drm/i915: Disable THP until we have a GPU read BW W/A
drm/i915/gvt: Correct ADDR_4K/2M/1G_MASK definition
drm/i915/gvt: enabled pipe A default on creating vgpu
drm/i915/gvt: Move request alloc to dispatch_workload path only
drm/i915/gvt: remove skl_misc_ctl_write handler
drm/i915/gvt: Fix unsafe locking caused by spin_unlock_bh
drm/i915: fix intel_backlight_device_register declaration
drm/i915/fbdev: Serialise early hotplug events with async fbdev config
drm/i915: Prevent zero length "index" write
drm/i915: Don't try indexed reads to alternate slave addresses
Peter Rosin [Mon, 27 Nov 2017 16:31:00 +0000 (17:31 +0100)]
hwmon: (jc42) optionally try to disable the SMBUS timeout
With a nxp,se97 chip on an atmel sama5d31 board, the I2C adapter driver
is not always capable of avoiding the 25-35 ms timeout as specified by
the SMBUS protocol. This may cause silent corruption of the last bit of
any transfer, e.g. a one is read instead of a zero if the sensor chip
times out. This also affects the eeprom half of the nxp-se97 chip, where
this silent corruption was originally noticed. Other I2C adapters probably
suffer similar issues, e.g. bit-banging comes to mind as risky...
The SMBUS register in the nxp chip is not a standard Jedec register, but
it is not special to the nxp chips either, at least the atmel chips
have the same mechanism. Therefore, do not special case this on the
manufacturer, it is opt-in via the device property anyway.
Cc: stable@vger.kernel.org # 4.9+ Signed-off-by: Peter Rosin <peda@axentia.se> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
projects / mirror_ubuntu-kernels.git / log