This code is really spurious.
It always returns an ERR_PTR, even when err is known to be 0 and calls
put_device() after a successful device_register() call.
It is likely that the return statement in the normal path is missing.
Add 'return rdev;' to fix it.
Fixes: d787dcdb9c8f ("bus: sunxi-rsb: Add driver for Allwinner Reduced Serial Bus") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Samuel Holland <samuel@sholland.org> Tested-by: Samuel Holland <samuel@sholland.org> Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com> Link: https://lore.kernel.org/r/ef2b9576350bba4c8e05e669e9535e9e2a415763.1650551719.git.christophe.jaillet@wanadoo.fr Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Fixes: 5b0b9e4c2c89 ("tcp: md5: incorrect tcp_header_len for incoming connections") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Francesco Ruggeri <fruggeri@arista.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
I had this bug sitting for too long in my pile, it is time to fix it.
Thanks to Doug Porter for reminding me of it!
We had various attempts in the past, including commit 0cbe6a8f089e ("tcp: remove SOCK_QUEUE_SHRUNK"),
but the issue is that TCP stack currently only generates
EPOLLOUT from input path, when tp->snd_una has advanced
and skb(s) cleaned from rtx queue.
If a flow has a big RTT, and/or receives SACKs, it is possible
that the notsent part (tp->write_seq - tp->snd_nxt) reaches 0
and no more data can be sent until tp->snd_una finally advances.
What is needed is to also check if POLLOUT needs to be generated
whenever tp->snd_nxt is advanced, from output path.
This bug triggers more often after an idle period, as
we do not receive ACK for at least one RTT. tcp_notsent_lowat
could be a fraction of what CWND and pacing rate would allow to
send during this RTT.
In a followup patch, I will remove the bogus call
to tcp_chrono_stop(sk, TCP_CHRONO_SNDBUF_LIMITED)
from tcp_check_space(). Fact that we have decided to generate
an EPOLLOUT does not mean the application has immediately
refilled the transmit queue. This optimistic call
might have been the reason the bug seemed not too serious.
Tested:
200 ms rtt, 1% packet loss, 32 MB tcp_rmem[2] and tcp_wmem[2]
$ echo 500000 >/proc/sys/net/ipv4/tcp_notsent_lowat
$ cat bench_rr.sh
SUM=0
for i in {1..10}
do
V=`netperf -H remote_host -l30 -t TCP_RR -- -r 10000000,10000 -o LOCAL_BYTES_SENT | egrep -v "MIGRATED|Bytes"`
echo $V
SUM=$(($SUM + $V))
done
echo SUM=$SUM
As pointed out by Jakub Kicinski, currently using TUNNEL_SEQ in
collect_md mode is racy for [IP6]GRE[TAP] devices. Consider the
following sequence of events:
1. An [IP6]GRE[TAP] device is created in collect_md mode using "ip link
add ... external". "ip" ignores "[o]seq" if "external" is specified,
so TUNNEL_SEQ is off, and the device is marked as NETIF_F_LLTX (i.e.
it uses lockless TX);
2. Someone sets TUNNEL_SEQ on outgoing skb's, using e.g.
bpf_skb_set_tunnel_key() in an eBPF program attached to this device;
3. gre_fb_xmit() or __gre6_xmit() processes these skb's:
Since we are not using the TX lock (&txq->_xmit_lock), multiple CPUs may
try to do this tunnel->o_seqno++ in parallel, which is racy. Fix it by
making o_seqno atomic_t.
As mentioned by Eric Dumazet in commit b790e01aee74 ("ip_gre: lockless
xmit"), making o_seqno atomic_t increases "chance for packets being out
of order at receiver" when NETIF_F_LLTX is on.
Maybe a better fix would be:
1. Do not ignore "oseq" in external mode. Users MUST specify "oseq" if
they want the kernel to allow sequencing of outgoing packets;
2. Reject all outgoing TUNNEL_SEQ packets if the device was not created
with "oseq".
Unfortunately, that would break userspace.
We could now make [IP6]GRE[TAP] devices always NETIF_F_LLTX, but let us
do it in separate patches to keep this fix minimal.
Suggested-by: Jakub Kicinski <kuba@kernel.org> Fixes: 77a5196a804e ("gre: add sequence number for collect md mode.") Signed-off-by: Peilin Ye <peilin.ye@bytedance.com> Acked-by: William Tu <u9012063@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
For IP6GRE and IP6GRETAP devices, currently o_seqno starts from 1 in
native mode. According to RFC 2890 2.2., "The first datagram is sent
with a sequence number of 0." Fix it.
It is worth mentioning that o_seqno already starts from 0 in collect_md
mode, see the "if (tunnel->parms.collect_md)" clause in __gre6_xmit(),
where tunnel->o_seqno is passed to gre_build_header() before getting
incremented.
Fixes: c12b395a4664 ("gre: Support GRE over IPv6") Signed-off-by: Peilin Ye <peilin.ye@bytedance.com> Acked-by: William Tu <u9012063@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
For GRE and GRETAP devices, currently o_seqno starts from 1 in native
mode. According to RFC 2890 2.2., "The first datagram is sent with a
sequence number of 0." Fix it.
It is worth mentioning that o_seqno already starts from 0 in collect_md
mode, see gre_fb_xmit(), where tunnel->o_seqno is passed to
gre_build_header() before getting incremented.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Peilin Ye <peilin.ye@bytedance.com> Acked-by: William Tu <u9012063@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In the current implementation, when TCP initiates a connection
to an unavailable [ip,port], ECONNREFUSED will be stored in the
TCP socket, but SMC will not. However, some apps (like curl) use
getsockopt(,,SO_ERROR,,) to get the error information, which makes
them miss the error message and behave strangely.
Fixes: 50717a37db03 ("net/smc: nonblocking connect rework") Signed-off-by: liuyacan <liuyacan@corp.netease.com> Reviewed-by: Tony Lu <tonylu@linux.alibaba.com> Acked-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Currently, there are some querying mailboxes sent from VF to PF,
and VF will wait the PF's handling result. For mailbox
HCLGE_MBX_GET_QID_IN_PF and HCLGE_MBX_GET_RSS_KEY, it may fail
when the input parameter is invalid, but the prototype of their
handler function is void. In this case, PF always return success
to VF, which may cause the VF get incorrect result.
Fixes it by adding return value for these function.
Fixes: 63b1279d9905 ("net: hns3: check queue id range before using") Fixes: 532cfc0df1e4 ("net: hns3: add a check for index in hclge_get_rss_key()") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Add validity check for message data length in function
hclge_send_mbx_msg(), avoid unexpected overflow.
Fixes: dde1a86e93ca ("net: hns3: Add mailbox support to PF driver") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Currently, function hclge_get_ring_chain_from_mbx will return -ENOMEM if
ring_num is bigger than HCLGE_MBX_MAX_RING_CHAIN_PARAM_NUM. It is better to
return -EINVAL for the invalid parameter case.
So this patch fixes it by return -EINVAL in this abnormal branch.
Fixes: 5d02a58dae60 ("net: hns3: fix for buffer overflow smatch warning") Signed-off-by: Jie Wang <wangjie125@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If failed to register netdev, it needs to clear INITED state and stop
client in case of cause problem when concurrency with uninitialized
process of driver.
Fixes: a289a7e5c1d4 ("net: hns3: put off calling register_netdev() until client initialize complete") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
if sun50i_cpufreq_get_efuse failed, then opp_tables leak.
Fixes: f328584f7bff ("cpufreq: Add sun50i nvmem based CPU scaling driver") Signed-off-by: Xiaobing Luo <luoxiaobing0926@gmail.com> Reviewed-by: Samuel Holland <samuel@sholland.org> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The correct spelling for the property is gpios. Otherwise, the regulator
will neither reserve nor control any GPIOs. Thus, any SD/MMC card which
can use UHS-I modes will fail.
A null pointer reference issue can be triggered when the response of a
stream reconf request arrives after the timer is triggered, such as:
send Incoming SSN Reset Request --->
CPU0:
reconf timer is triggered,
go to the handler code before hold sk lock
<--- reply with Outgoing SSN Reset Request
CPU1:
process Outgoing SSN Reset Request,
and set asoc->strreset_chunk to NULL
CPU0:
continue the handler code, hold sk lock,
and try to hold asoc->strreset_chunk, crash!
When we try to transmit an skb with md_dst attached through wireguard
we hit a null pointer dereference in wg_xmit() due to the use of
dst_mtu() which calls into dst_blackhole_mtu() which in turn tries to
dereference dst->dev.
Since wireguard doesn't use md_dsts we should use skb_valid_dst(), which
checks for DST_METADATA flag, and if it's set, then falls back to
wireguard's device mtu. That gives us the best chance of transmitting
the packet; otherwise if the blackhole netdev is used we'd get
ETH_MIN_MTU.
If an ACK (s)acks multiple skbs, we favor the information
from the most recently sent skb by choosing the skb with
the highest prior_delivered count. But in the interval
between receiving ACKs, we send multiple skbs with the same
prior_delivered, because the tp->delivered only changes
when we receive an ACK.
We used RACK's solution, copying tcp_rack_sent_after() as
tcp_skb_sent_after() helper to determine "which packet was
sent last?". Later, we will use tcp_skb_sent_after() instead
in RACK.
Fixes: b9f64820fb22 ("tcp: track data delivery rate for a TCP connection") Signed-off-by: Pengcheng Yang <yangpc@wangsu.com> Cc: Paolo Abeni <pabeni@redhat.com> Acked-by: Neal Cardwell <ncardwell@google.com> Tested-by: Neal Cardwell <ncardwell@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/1650422081-22153-1-git-send-email-yangpc@wangsu.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The current EOI handler for LEVEL triggered interrupts calls clk_enable(),
register IO, clk_disable(). The clock manipulation requires locking which
happens with IRQs disabled in clk_enable_lock(). Instead of turning the
clock on and off all the time, enable the clock in case LEVEL interrupt is
requested and keep the clock enabled until all LEVEL interrupts are freed.
The LEVEL interrupts are an exception on this platform and seldom used, so
this does not affect the common case.
This simplifies the LEVEL interrupt handling considerably and also fixes
the following splat found when using preempt-rt:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at kernel/locking/rtmutex.c:2040 __rt_mutex_trylock+0x37/0x62
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.10.109-rt65-stable-standard-00068-g6a5afc4b1217 #85
Hardware name: STM32 (Device Tree Support)
[<c010a45d>] (unwind_backtrace) from [<c010766f>] (show_stack+0xb/0xc)
[<c010766f>] (show_stack) from [<c06353ab>] (dump_stack+0x6f/0x84)
[<c06353ab>] (dump_stack) from [<c01145e3>] (__warn+0x7f/0xa4)
[<c01145e3>] (__warn) from [<c063386f>] (warn_slowpath_fmt+0x3b/0x74)
[<c063386f>] (warn_slowpath_fmt) from [<c063b43d>] (__rt_mutex_trylock+0x37/0x62)
[<c063b43d>] (__rt_mutex_trylock) from [<c063c053>] (rt_spin_trylock+0x7/0x16)
[<c063c053>] (rt_spin_trylock) from [<c036a2f3>] (clk_enable_lock+0xb/0x80)
[<c036a2f3>] (clk_enable_lock) from [<c036ba69>] (clk_core_enable_lock+0x9/0x18)
[<c036ba69>] (clk_core_enable_lock) from [<c034e9f3>] (stm32_gpio_get+0x11/0x24)
[<c034e9f3>] (stm32_gpio_get) from [<c034ef43>] (stm32_gpio_irq_trigger+0x1f/0x48)
[<c034ef43>] (stm32_gpio_irq_trigger) from [<c014aa53>] (handle_fasteoi_irq+0x71/0xa8)
[<c014aa53>] (handle_fasteoi_irq) from [<c0147111>] (generic_handle_irq+0x19/0x22)
[<c0147111>] (generic_handle_irq) from [<c014752d>] (__handle_domain_irq+0x55/0x64)
[<c014752d>] (__handle_domain_irq) from [<c0346f13>] (gic_handle_irq+0x53/0x64)
[<c0346f13>] (gic_handle_irq) from [<c0100ba5>] (__irq_svc+0x65/0xc0)
Exception stack(0xc0e01f18 to 0xc0e01f60)
1f00: 0000300c00000000
1f20: 0000300cc010ff010000000000000000c0e00000c0e0771400000001c0e01f78
1f40: c0e0775800000000ef7cd0ffc0e01f68c010554bc010554240000033ffffffff
[<c0100ba5>] (__irq_svc) from [<c0105542>] (arch_cpu_idle+0xc/0x1e)
[<c0105542>] (arch_cpu_idle) from [<c063be95>] (default_idle_call+0x21/0x3c)
[<c063be95>] (default_idle_call) from [<c01324f7>] (do_idle+0xe3/0x1e4)
[<c01324f7>] (do_idle) from [<c01327b3>] (cpu_startup_entry+0x13/0x14)
[<c01327b3>] (cpu_startup_entry) from [<c0a00c13>] (start_kernel+0x397/0x3d4)
[<c0a00c13>] (start_kernel) from [<00000000>] (0x0)
---[ end trace 0000000000000002 ]---
Power consumption measured on STM32MP157C DHCOM SoM is not increased or
is below noise threshold.
Fixes: 47beed513a85b ("pinctrl: stm32: Add level interrupt support to gpio irq chip") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: Fabien Dessenne <fabien.dessenne@foss.st.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Marc Zyngier <maz@kernel.org> Cc: linux-stm32@st-md-mailman.stormreply.com Cc: linux-arm-kernel@lists.infradead.org
To: linux-gpio@vger.kernel.org Reviewed-by: Fabien Dessenne <fabien.dessenne@foss.st.com> Link: https://lore.kernel.org/r/20220421140827.214088-1-marex@denx.de Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In tcp_create_openreq_child we adjust tcp_header_len for md5 using the
remote address in newsk. But that address is still 0 in newsk at this
point, and it is only set later by the callers (tcp_v[46]_syn_recv_sock).
Use the address from the request socket instead.
Fixes: cfb6eeb4c860 ("[TCP]: MD5 Signature Option (RFC2385) support.") Signed-off-by: Francesco Ruggeri <fruggeri@arista.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20220421005026.686A45EC01F2@us226.sjc.aristanetworks.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
xmit_check_hhlen() observes the dst for getting the device hard header
length to make sure a modified packet can fit. When a helper which changes
the dst - such as bpf_skb_set_tunnel_key() - is called as part of the
xmit program the accessed dst is no longer valid.
Extend d2df92e98a34 ("netfilter: nft_set_rbtree: handle element
re-addition after deletion") to deal with elements with same end flags
in the same transation.
Reset the overlap flag as described by 7c84d41416d8 ("netfilter:
nft_set_rbtree: Detect partial overlaps on insertion").
Fixes: 7c84d41416d8 ("netfilter: nft_set_rbtree: Detect partial overlaps on insertion") Fixes: d2df92e98a34 ("netfilter: nft_set_rbtree: handle element re-addition after deletion") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Reviewed-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The device_node pointer is returned by of_parse_phandle() with refcount
incremented. We should use of_node_put() on it when done.
of_node_put() will check for NULL value.
Fixes: a20f997010c4 ("net: dsa: Don't instantiate phylink for CPU/DSA ports unless needed") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
rpc-if-hyperflash rpc-if-hyperflash: probing of hyperbus device failed
In HyperFlash or Octal-SPI Flash mode, the Transfer Data Enable bits
(SPIDE) in the Manual Mode Enable Setting Register (SMENR) are derived
from half of the transfer size, cfr. the rpcif_bits_set() helper
function. However, rpcif_reg_{read,write}() does not take the bus size
into account, and does not double all Manual Mode Data Register access
sizes when communicating with a HyperFlash or Octal-SPI Flash device.
Fix this, and avoid the back-and-forth conversion between transfer size
and Transfer Data Enable bits, by explicitly storing the transfer size
in struct rpcif, and using that value to determine access size in
rpcif_reg_{read,write}().
Enforce that the "high" Manual Mode Read/Write Data Registers
(SM[RW]DR1) are only used for 8-byte data accesses.
While at it, forbid writing to the Manual Mode Read Data Registers,
as they are read-only.
Fixes: fff53a551db50f5e ("memory: renesas-rpc-if: Correct QSPI data transfer in Manual mode") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Link: https://lore.kernel.org/r/cde9bfacf704c81865f57b15d1b48a4793da4286.1649681476.git.geert+renesas@glider.be Link: https://lore.kernel.org/r/20220420070526.9367-1-krzysztof.kozlowski@linaro.org' Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The stm32_gpio_get() should only be called for LEVEL triggered interrupts,
skip calling it for EDGE triggered interrupts altogether to avoid wasting
CPU cycles in EOI handler. On this platform, EDGE triggered interrupts are
the majority and LEVEL triggered interrupts are the exception no less, and
the CPU cycles are not abundant.
Fixes: 47beed513a85b ("pinctrl: stm32: Add level interrupt support to gpio irq chip") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: Fabien Dessenne <fabien.dessenne@foss.st.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Marc Zyngier <maz@kernel.org> Cc: linux-stm32@st-md-mailman.stormreply.com Cc: linux-arm-kernel@lists.infradead.org
To: linux-gpio@vger.kernel.org Link: https://lore.kernel.org/r/20220415215410.498349-1-marex@denx.de Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Commit 46b5889cc2c5 ("mtd: implement proper partition handling")
started using "mtd_get_master_ofs()" in mtd callbacks to determine
memory offsets by means of 'part' field from mtd_info, what previously
was smashed accessing 'master' field in the mtd_set_dev_defaults() method.
That provides wrong offset what causes hardware access errors.
Just make 'part', 'master' as separate fields, rather than using
union type to avoid 'part' data corruption when mtd_set_dev_defaults()
is called.
wait_for_completion_timeout() returns unsigned long not int.
It returns 0 if timed out, and positive if completed.
The check for <= 0 is ambiguous and should be == 0 here
indicating timeout which is the only error case.
Fixes: 83738d87e3a0 ("mtd: sh_flctl: Add DMA capabilty") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220412083435.29254-1-linmq006@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If EINT_MTK is m and PINCTRL_MTK_V2 is y, build fails:
drivers/pinctrl/mediatek/pinctrl-moore.o: In function `mtk_gpio_set_config':
pinctrl-moore.c:(.text+0xa6c): undefined reference to `mtk_eint_set_debounce'
drivers/pinctrl/mediatek/pinctrl-moore.o: In function `mtk_gpio_to_irq':
pinctrl-moore.c:(.text+0xacc): undefined reference to `mtk_eint_find_irq'
Select EINT_MTK for PINCTRL_MTK_V2 to fix this.
Fixes: 8174a8512e3e ("pinctrl: mediatek: make MediaTek pinctrl v2 driver ready for buidling loadable module") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Link: https://lore.kernel.org/r/20220409105958.37412-1-yuehaibing@huawei.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If clk_prepare_enable() fails we call clk_disable_unprepare()
in the error path what results in a warning that the clock
is disabled and unprepared already.
And if we fail later in phy_g12a_usb3_pcie_probe() then we
bail out w/o calling clk_disable_unprepare().
This patch fixes both errors.
The pinout of the OMAP35 and DM37 variants of the SOM-LV are the
same, but the macros which define the pinmuxing are different
between OMAP3530 and DM3730. The pinmuxing was correct for
for the DM3730, but wrong for the OMAP3530. Since the boot loader
was correctly pin-muxing the pins, this was not obvious. As the
bootloader not guaranteed to pinmux all the pins any more, this
causes an issue, so the pinmux needs to be moved from a common
file to their respective board files.
Fixes: f8a2e3ff7103 ("ARM: dts: Add minimal support for LogicPD OMAP35xx SOM-LV devkit") Signed-off-by: Adam Ford <aford173@gmail.com>
Message-Id: <20220303171818.11060-1-aford173@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The bootloader for the AM3517 has previously done much of the pin
muxing, but as the bootloader is moving more and more to a model
based on the device tree, it may no longer automatically mux the
pins, so it is necessary to add the pinmuxing to the Linux device
trees so the respective peripherals can remain functional.
Fixes: 6ed1d7997561 ("ARM: dts: am3517-evm: Add support for UI board and Audio") Signed-off-by: Adam Ford <aford173@gmail.com>
Message-Id: <20220226214820.747847-1-aford173@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Commit a1ebdb374199 ("ARM: dts: Fix swapped mmc order for omap3")
introduces general mmc aliases. Let's tailor them to the need
of the GTA04 board which does not make use of mmc2 and mmc3 interfaces.
Fixes: a1ebdb374199 ("ARM: dts: Fix swapped mmc order for omap3") Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Message-Id: <dc9173ee3d391d9e92b7ab8ed4f84b29f0a21c83.1646744420.git.hns@goldelico.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Similar to the sc7180 commit, let's drop the IP0 interconnects here
because the IP0 resource is also used in the clk-rpmh driver on sdx55.
It's bad to have the clk framework and interconnect framework control
the same RPMh resource without any coordination. The rpmh driver in the
kernel doesn't aggregate resources between clients either, so leaving
control to clk-rpmh avoids any issues with unused interconnects turning
off IP0 behind the back of the clk framework.
Cc: Alex Elder <elder@linaro.org> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Taniya Das <quic_tdas@quicinc.com> Cc: Mike Tipton <quic_mdtipton@quicinc.com> Fixes: b2150cab9a97 ("clk: qcom: rpmh: add support for SDX55 rpmh IPA clock") Signed-off-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Alex Elder <elder@linaro.org> Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20220412220033.1273607-3-swboyd@chromium.org Signed-off-by: Georgi Djakov <djakov@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The pm_runtime_enable() will increase power disable depth.
If the probe fails, we should use pm_runtime_disable() to balance
pm_runtime_enable().
Add missing pm_runtime_disable() for serdes_am654_probe().
Fixes: 71e2f5c5c224 ("phy: ti: Add a new SERDES driver for TI's AM654x SoC") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Link: https://lore.kernel.org/r/20220301025853.1911-1-linmq006@gmail.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The pm_runtime_enable will increase power disable depth.
If the probe fails, we should use pm_runtime_disable() to balance
pm_runtime_enable(). And use pm_runtime_dont_use_autosuspend() to
undo pm_runtime_use_autosuspend()
In the PM Runtime docs:
Drivers in ->remove() callback should undo the runtime PM changes done
in ->probe(). Usually this means calling pm_runtime_disable(),
pm_runtime_dont_use_autosuspend() etc.
We should do this in error handling.
Fixes: f7f50b2a7b05 ("phy: mapphone-mdm6600: Add runtime PM support for n_gsm on USB suspend") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Link: https://lore.kernel.org/r/20220301024615.31899-1-linmq006@gmail.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Commit bf781869e5cf ("ARM: dts: at91: add pinctrl-{names, 0} for all
gpios") introduces pinctrl phandles for pins used by individual
controllers to avoid failures due to commit 2ab73c6d8323 ("gpio:
Support GPIO controllers without pin-ranges"). For SPI controllers
available on SAMA5D4 and SAMA5D3 some of the pins are defined in
SoC specific dtsi on behalf of pinctrl-0. Adding extra pinctrl phandles
on board specific dts also on behalf of pinctrl-0 overwrite the pinctrl-0
phandle specified in SoC specific dtsi. Thus add the board specific
pinctrl to pinctrl-1.
The MCLK of the WM8731 on the AT91SAM9G20-EK board is connected to the
PCK0 output of the SoC and is expected to be set to 12MHz. Previously
this was mapped using pre-common clock API calls in the audio machine
driver but the conversion to the common clock framework broke that so
describe things in the DT instead.
Fixes: ff78a189b0ae55f ("ARM: at91: remove old at91-specific clock driver") Signed-off-by: Mark Brown <broonie@kernel.org> Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Link: https://lore.kernel.org/r/20220404102806.581374-2-broonie@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The corresponding API for clk_prepare_enable is clk_disable_unprepare.
Make sure that the clock is unprepared on exit by changing clk_disable
to clk_disable_unprepare.
Fixes: ed31ee7cf1fe ("phy: ti: usb2: Fix logic on -EPROBE_DEFER") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Link: https://lore.kernel.org/r/20220318105748.19532-1-linmq006@gmail.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
We currently are getting the following warning after a system suspend:
Powerdomain (vpe_pwrdm) didn't enter target state 0
Looks like this is because the STANDBYMODE bit for SMART_IDLE should
not be used. The TRM "Table 12-348. VPE_SYSCONFIG" says that the value
for SMART_IDLE is "0x2: Same behavior as bit-field value of 0x1". But
if the SMART_IDLE value is used, PM_VPE_PWRSTST LASTPOWERSTATEENTERED
bits always show value of 3.
Let's fix the issue by dropping SMART_IDLE for vpe. And let's also add
the missing the powerdomain for vpe.
Fixes: 1a2095160594 ("ARM: dts: dra7: Add ti-sysc node for VPE") Cc: Benoit Parrot <bparrot@ti.com> Reported-by: Kevin Hilman <khilman@baylibre.com> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
On beagleboard revisions A to B4 we need to use gpt12 as the system timer.
However, the quirk handling added for gpt12 caused a regression for system
suspend for am335x as the PM coprocessor needs the timers idled for
suspend.
Let's make the gpt12 quirk specific to omap34xx, other SoCs don't need
it. Beagleboard revisions C and later no longer need to use the gpt12
related quirk. Then at some point, if we decide to drop support for the old
beagleboard revisions A to B4, we can also drop the gpt12 related quirks
completely.
Fixes: 3ff340e24c9d ("bus: ti-sysc: Fix gpt12 system timer issue with reserved status") Reported-by: Kevin Hilman <khilman@baylibre.com> Suggested-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The of_find_compatible_node() function returns a node pointer with
refcount incremented, We should use of_node_put() on it when done
Add the missing of_node_put() to release the refcount.
Fixes: fd1c07861491 ("ARM: OMAP4: Fix the init code to have OMAP4460 errata available in DT build") Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Message-Id: <20220309104302.18398-1-linmq006@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The labels for lines 61 through 84 on the periphs-banks were offset by 2.
2 lines are missing in the BOOT GPIO lines (contains 14, should be 16)
Added 2 empty entries in BOOT to realigned the rest of GPIO labels
to match the Banana Pi M5 schematics.
(Thanks to Neil Armstrong for the heads up on the position of the missing pins)
Fixes: 976e920183e4 ("arm64: dts: meson-sm1: add Banana PI BPI-M5 board dts") Signed-off-by: Guillaume Giraudon <ggiraudon@prism19.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://lore.kernel.org/r/20220411144427.874-1-ggiraudon@prism19.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The most specific compatible string element should be "fsl,imx8mn-sai"
on i.MX8M Nano, fix it from current "fsl,imx8mm-sai" (two Ms, likely
due to copy-paste error from i.MX8M Mini).
Fixes: 9e9860069725f ("arm64: dts: imx8mn: Add SAI nodes") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Adam Ford <aford173@gmail.com> Cc: Fabio Estevam <festevam@gmail.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Shawn Guo <shawnguo@kernel.org> Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org Reviewed-by: Adam Ford <aford173@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
On a custom carrier board with a i.MX6Q Apalis SoM, the sgtl5000 codec
on the SoM is often not detected and the following error message is
seen when the sgtl5000 driver tries to read the ID register:
sgtl5000 1-000a: Error reading chip id -6
The reason for the error is that the MCLK clock is not provided
early enough.
Fix the problem by describing the MCLK pinctrl inside the codec
node instead of placing it inside the audmux pinctrl group.
With this change applied the sgtl5000 is always detected on every boot.
Fixes: 693e3ffaae5a ("ARM: dts: imx6: Add support for Toradex Apalis iMX6Q/D SoM") Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Tim Harvey <tharvey@gateworks.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In some situations software handles TRB events slower than adding TRBs.
If the number of TRB events to be processed in a given interrupt is exactly
the same as the event ring size 256, then the local variable
"event_ring_deq" that holds the initial dequeue position is equal to
software_dequeue after handling all 256 interrupts.
It will cause driver to not update ERDP to hardware,
Software dequeue pointer is out of sync with ERDP on interrupt exit.
On the next interrupt, the event ring may full but driver will not
update ERDP as software_dequeue is equal to ERDP.
Hardware ERDP is updated mid event handling if there are more than 128
events in an interrupt (half of ring size).
Fix this by updating the software local variable at the same time as
hardware ERDP.
[commit message rewording -Mathias]
Fixes: dc0ffbea5729 ("usb: host: xhci: update event ring dequeue pointer on purpose") Reviewed-by: Peter Chen <peter.chen@kernel.org> Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20220408134823.2527272-2-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The fsl,scu.txt dt-binding documentation explicitly mentions
that the compatible string should be either "fsl,imx8qm-clock"
or "fsl,imx8qxp-clock", followed by "fsl,scu-clk". Also, i.MX8qm
SCU clocks and i.MX8qxp SCU clocks are really not the same, so
we have to set the compatible property according to SoC name.
Let's correct the i.MX8qm clock controller's compatible property
from
"fsl,imx8qxp-clk", "fsl,scu-clk"
to
"fsl,imx8qm-clk", "fsl,scu-clk" .
Fixes: f2180be18a63 ("arm64: dts: imx: add imx8qm common dts file") Cc: Rob Herring <robh+dt@kernel.org> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP Linux Team <linux-imx@nxp.com> Signed-off-by: Liu Ying <victor.liu@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
While checking AF_XDP copy mode combined with busy poll, strange
results were observed. rxdrop and txonly scenarios worked fine, but
l2fwd broke immediately.
After a deeper look, it turned out that for l2fwd, Tx side was exiting
early due to xsk_no_wakeup() returning true and in the end
xsk_generic_xmit() was never called. Note that AF_XDP Tx in copy mode
is syscall steered, so the current behavior is broken.
Txonly scenario only worked due to the fact that
sk_mark_napi_id_once_xdp() was never called - since Rx side is not in
the picture for this case and mentioned function is called in
xsk_rcv_check(), sk::sk_napi_id was never set, which in turn meant that
xsk_no_wakeup() was returning false (see the sk->sk_napi_id >=
MIN_NAPI_ID check in there).
To fix this, prefer busy poll in xsk_sendmsg() only when zero copy is
enabled on a given AF_XDP socket. By doing so, busy poll in copy mode
would not exit early on Tx side and eventually xsk_generic_xmit() will
be called.
Fixes: a0731952d9cd ("xsk: Add busy-poll support for {recv,send}msg()") Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20220406155804.434493-1-maciej.fijalkowski@intel.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
According to the datasheet, mt7622 only has 5 ECC capabilities instead
of 7, and the decoding error register is arranged as follows:
+------+---------+---------+---------+---------+
| Bits | 19:15 | 14:10 | 9:5 | 4:0 |
+------+---------+---------+---------+---------+
| Name | ERRNUM3 | ERRNUM2 | ERRNUM1 | ERRNUM0 |
+------+---------+---------+---------+---------+
This means err_mask should be 0x1f instead of 0x3f and the number of
bits shifted in mtk_ecc_get_stats should be 5 instead of 8.
This commit introduces err_shift for the difference in this register
and fix other existing parameters.
Public MT7622 reference manual can be found on [0] and the info this
commit is based on is from page 656 and page 660.
Amlogic SM1 devices experience CPU stalls and random board wedges when
the system idles and CPU cores clock down to lower opp points. Recent
vendor kernels include a change to remove 100-250MHz and other distro
sources also remove the 500/667MHz points. Unless all 100-667Mhz opps
are removed or the CPU governor forced to performance stalls are still
observed, so let's remove them to improve stability and uptime.
Fixes: 3d9e76483049 ("arm64: dts: meson-sm1-sei610: enable DVFS") Signed-off-by: Christian Hewitt <christianshewitt@gmail.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://lore.kernel.org/r/20220210100638.19130-3-christianshewitt@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Amlogic G12B devices experience CPU stalls and random board wedges when
the system idles and CPU cores clock down to lower opp points. Recent
vendor kernels include a change to remove 100-250MHz and other distro
sources also remove the 500/667MHz points. Unless all 100-667Mhz opps
are removed or the CPU governor forced to performance stalls are still
observed, so let's remove them to improve stability and uptime.
Fixes: b96d4e92709b ("arm64: dts: meson-g12b: support a311d and s922x cpu operating points") Signed-off-by: Christian Hewitt <christianshewitt@gmail.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://lore.kernel.org/r/20220210100638.19130-2-christianshewitt@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
On QCOM platforms with EPSS flavour of cpufreq IP a throttled frequency is
obtained from another register REG_DOMAIN_STATE, thus the helper function
qcom_lmh_get_throttle_freq() should be modified accordingly, as for now
it returns gibberish since .reg_current_vote is unset for EPSS hardware.
To exclude a hardcoded magic number 19200 it is replaced by "xo" clock rate
in KHz.
The driver would disable the worker when cpu is being put offline, but
it happens closer to the end of cpufreq_offline(). The function
qcom_lmh_dcvs_poll() can be running in parallel with this, when
policy->cpus already has been updated. Read policy->related_cpus
instead.
We received a report[1] of kernel crashes when Cilium is used in XDP
mode with virtio_net after updating to newer kernels. After
investigating the reason it turned out that when using mergeable bufs
with an XDP program which adjusts xdp.data or xdp.data_meta page_to_buf()
calculates the build_skb address wrong because the offset can become less
than the headroom so it gets the address of the previous page (-X bytes
depending on how lower offset is):
page_to_skb: page addr ffff9eb2923e2000 buf ffff9eb2923e1ffc offset 252 headroom 256
This is a pr_err() I added in the beginning of page_to_skb which clearly
shows offset that is less than headroom by adding 4 bytes of metadata
via an xdp prog. The calculations done are:
receive_mergeable():
headroom = VIRTIO_XDP_HEADROOM; // VIRTIO_XDP_HEADROOM == 256 bytes
offset = xdp.data - page_address(xdp_page) -
vi->hdr_len - metasize;
page_to_skb():
p = page_address(page) + offset;
...
buf = p - headroom;
Now buf goes -4 bytes from the page's starting address as can be seen
above which is set as skb->head and skb->data by build_skb later. Depending
on what's done with the skb (when it's freed most often) we get all kinds
of corruptions and BUG_ON() triggers in mm[2]. We have to recalculate
the new headroom after the xdp program has run, similar to how offset
and len are recalculated. Headroom is directly related to
data_hard_start, data and data_meta, so we use them to get the new size.
The result is correct (similar pr_err() in page_to_skb, one case of
xdp_page and one case of virtnet buf):
a) Case with 4 bytes of metadata
[ 115.949641] page_to_skb: page addr ffff8b4dcfad2000 offset 252 headroom 252
[ 121.084105] page_to_skb: page addr ffff8b4dcf018000 offset 20732 headroom 252
b) Case of pushing data +32 bytes
[ 153.181401] page_to_skb: page addr ffff8b4dd0c4d000 offset 288 headroom 288
[ 158.480421] page_to_skb: page addr ffff8b4dd00b0000 offset 24864 headroom 288
c) Case of pushing data -33 bytes
[ 835.906830] page_to_skb: page addr ffff8b4dd3270000 offset 223 headroom 223
[ 840.839910] page_to_skb: page addr ffff8b4dcdd68000 offset 12511 headroom 223
Offset and headroom are equal because offset points to the start of
reserved bytes for the virtio_net header which are at buf start +
headroom, while data points at buf start + vnet hdr size + headroom so
when data or data_meta are adjusted by the xdp prog both the headroom size
and the offset change equally. We can use data_hard_start to compute the
new headroom after the xdp prog (linearized / page start case, the
virtnet buf case is similar just with bigger base offset):
xdp.data_hard_start = page_address + vnet_hdr
xdp.data = page_address + vnet_hdr + headroom
new headroom after xdp prog = xdp.data - xdp.data_hard_start - metasize
compile: clang -O2 -g -Wall -target bpf -c xdp_pass.c -o xdp_pass.o
load on virtio_net: ip link set enp1s0 xdpdrv obj xdp_pass.o sec xdp_pass
CC: stable@vger.kernel.org CC: Jason Wang <jasowang@redhat.com> CC: Xuan Zhuo <xuanzhuo@linux.alibaba.com> CC: Daniel Borkmann <daniel@iogearbox.net> CC: "Michael S. Tsirkin" <mst@redhat.com> CC: virtualization@lists.linux-foundation.org Fixes: 8fb7da9e9907 ("virtio_net: get build_skb() buf by data ptr") Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org> Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Link: https://lore.kernel.org/r/20220425103703.3067292-1-razor@blackwall.org Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When an iocg is in debt, its inuse weight is owned by debt handling and
should stay at 1. This invariant was broken when determining the amount of
surpluses at the beginning of donation calculation - when an iocg's
hierarchical weight is too low, the iocg is excluded from donation
calculation and its inuse is reset to its active regardless of its
indebtedness, triggering warnings like the following:
As this happens only when an iocg's hierarchical weight is negligible, its
impact likely is limited to triggering the warnings. Fix it by skipping
resetting inuse of under-weighted debtors.
When a XEN_HVM guest uses the XEN PIRQ/Eventchannel mechanism, then
PCI/MSI[-X] masking is solely controlled by the hypervisor, but contrary to
XEN_PV guests this does not disable PCI/MSI[-X] masking in the PCI/MSI
layer.
This can lead to a situation where the PCI/MSI layer masks an MSI[-X]
interrupt and the hypervisor grants the write despite the fact that it
already requested the interrupt. As a consequence interrupt delivery on the
affected device is not happening ever.
Set pci_msi_ignore_mask to prevent that like it's done for XEN_PV guests
already.
These patch_text implementations are using stop_machine_cpuslocked
infrastructure with atomic cpu_count. The original idea: When the
master CPU patch_text, the others should wait for it. But current
implementation is using the first CPU as master, which couldn't
guarantee the remaining CPUs are waiting. This patch changes the
last CPU as the master to solve the potential risk.
If we pass too short string to "hex2bin" (and the string size without
the terminating NUL character is even), "hex2bin" reads one byte after
the terminating NUL character. This patch fixes it.
Note that hex_to_bin returns -1 on error and hex2bin return -EINVAL on
error - so we can't just return the variable "hi" or "lo" on error.
This inconsistency may be fixed in the next merge window, but for the
purpose of fixing this bug, we just preserve the existing behavior and
return -1 and -EINVAL.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Fixes: b78049831ffe ("lib: add error checking to hex2bin") Cc: stable@vger.kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The function hex2bin is used to load cryptographic keys into device
mapper targets dm-crypt and dm-integrity. It should take constant time
independent on the processed data, so that concurrently running
unprivileged code can't infer any information about the keys via
microarchitectural convert channels.
This patch changes the function hex_to_bin so that it contains no
branches and no memory accesses.
Note that this shouldn't cause performance degradation because the size
of the new function is the same as the size of the old function (on
x86-64) - and the new function causes no branch misprediction penalties.
I compile-tested this function with gcc on aarch64 alpha arm hppa hppa64
i386 ia64 m68k mips32 mips64 powerpc powerpc64 riscv sh4 s390x sparc32
sparc64 x86_64 and with clang on aarch64 arm hexagon i386 mips32 mips64
powerpc powerpc64 s390x sparc32 sparc64 x86_64 to verify that there are
no branches in the generated code.
The Samsung pinctrl drivers depend on OF_GPIO, which is part of GPIOLIB.
ARMv7 Exynos platform selects GPIOLIB and Samsung pinctrl drivers. ARMv8
Exynos selects only the latter leading to possible wrong configuration
on ARMv8 build:
WARNING: unmet direct dependencies detected for PINCTRL_EXYNOS
Depends on [n]: PINCTRL [=y] && OF_GPIO [=n] && (ARCH_EXYNOS [=y] || ARCH_S5PV210 || COMPILE_TEST [=y])
Selected by [y]:
- ARCH_EXYNOS [=y]
Always select the GPIOLIB from the Samsung pinctrl drivers to fix the
issue. This requires removing of OF_GPIO dependency (to avoid recursive
dependency), so add dependency on OF for COMPILE_TEST cases.
Reported-by: Necip Fazil Yildiran <fazilyildiran@gmail.com> Fixes: eed6b3eb20b9 ("arm64: Split out platform options to separate Kconfig") Cc: <stable@vger.kernel.org> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/r/20220420141407.470955-1-krzysztof.kozlowski@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Due to what looks like a copy-paste error, the ECSPI2_MISO pad is not
muxed for SPI mode and causes reads from a slave-device connected to the
SPI header to always return zero.
Configure the ECSPI2_MISO pad for SPI mode on the gw71xx, gw72xx and
gw73xx families of boards that got this wrong.
Fixes: 6f30b27c5ef5 ("arm64: dts: imx8mm: Add Gateworks i.MX 8M Mini Development Kits") Cc: stable@vger.kernel.org # 5.12 Cc: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
It is possible that the recovery work might be running while the freeze
gets executed (during hibernation etc.,). Currently, we don't powerdown
the stack if it is not up but if the recovery work completes after freeze,
then the device will be up afterwards. This will not be a sane situation.
So let's flush the recovery worker before trying to powerdown the device.
During hibernation process, once thaw() stage completes, the MHI endpoint
devices will be in M0 state post recovery. After that, the devices will be
powered down so that the system can enter the target sleep state. During
this stage, the PCI core will put the devices in D3hot. But this transition
is allowed by the MHI spec. The devices can only enter D3hot when it is in
M3 state.
So for fixing this issue, let's add the poweroff() callback that will get
executed before putting the system in target sleep state during
hibernation. This callback will power down the device properly so that it
could be restored during restore() or thaw() stage.
The request will be inserted into the ci->i_unsafe_dirops before
assigning the req->r_session, so it's possible that we will hit
NULL pointer dereference bug here.
Cc: stable@vger.kernel.org
URL: https://tracker.ceph.com/issues/55327 Signed-off-by: Xiubo Li <xiubli@redhat.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Tested-by: Aaron Tomlin <atomlin@redhat.com> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The EndRun PTP/1588 dual serial port device is based on the Oxford
Semiconductor OXPCIe952 UART device with the PCI vendor:device ID set
for EndRun Technologies and is therefore driven by a fixed 62.5MHz clock
input derived from the 100MHz PCI Express clock. The clock rate is
divided by the oversampling rate of 16 as it is supplied to the baud
rate generator, yielding the baud base of 3906250.
Replace the incorrect baud base of 4000000 with the right value of 3906250 then, complementing commit 6cbe45d8ac93 ("serial: 8250: Correct
the clock for OxSemi PCIe devices").
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Cc: stable <stable@kernel.org> Fixes: 1bc8cde46a159 ("8250_pci: Added driver for Endrun Technologies PTP PCIe card.") Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Link: https://lore.kernel.org/r/alpine.DEB.2.21.2204181515270.9383@angie.orcam.me.uk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Sticky MCR bits are lost in console restoration if console suspending
has been disabled. This currently affects the AFE bit, which works in
combination with RTS which we set, so we want to make sure the UART
retains control of its FIFO where previously requested. Also specific
drivers may need other bits in the future.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Fixes: 4516d50aabed ("serial: 8250: Use canary to restart console after suspend") Cc: stable@vger.kernel.org # v4.0+ Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Link: https://lore.kernel.org/r/alpine.DEB.2.21.2204181518490.9383@angie.orcam.me.uk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The current timeout for draining the tx fifo in RS485 mode is calculated by
multiplying the time it takes to transmit one character (with the given
baud rate) with the maximal number of characters in the tx queue.
This timeout is too short for two reasons:
First when calculating the time to transmit one character integer division
is used which may round down the result in case of a remainder of the
division.
Fix this by rounding up the division result.
Second the hardware may need additional time (e.g for first putting the
characters from the fifo into the shift register) before the characters are
actually put onto the wire.
To be on the safe side double the current maximum number of iterations
that are used to wait for the queue draining.
Commit 76821e222c18 ("serial: imx: ensure that RX irqs are off if RX is
off") accidentally enabled overrun interrupts unconditionally when
deferring DMA enable until after the receiver has been enabled during
startup.
Fix this by using the DMA-initialised instead of DMA-enabled flag to
determine whether overrun interrupts should be enabled.
Note that overrun interrupts are already accounted for in
imx_uart_clear_rx_errors() when using DMA since commit 41d98b5da92f
("serial: imx-serial - update RX error counters when DMA is used").
Fixes: 76821e222c18 ("serial: imx: ensure that RX irqs are off if RX is off") Cc: stable@vger.kernel.org # 4.17 Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20220411081957.7846-1-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
While support for working with a vbus was added, the regulator was never
actually gotten (despite what was documented). Fix this by actually
getting the supply from the device tree.
Fixes: 7acc9973e3c4 ("usb: phy: generic: add vbus support") Cc: stable <stable@kernel.org> Signed-off-by: Sean Anderson <sean.anderson@seco.com> Link: https://lore.kernel.org/r/20220425171412.1188485-3-sean.anderson@seco.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Path fixes bug which occurs during resetting endpoint in
__cdns3_gadget_ep_clear_halt function. During resetting endpoint
controller will change HW/DMA owned TRB. It set Abort flag in
trb->control and will change trb->length field. If driver want
to use the aborted trb it must update the changed field in
TRB.
If the user sets the usb_request's no_interrupt, then there will be no
completion event for the request. Currently the driver incorrectly uses
the event status of a different request to report the status for a
request with no_interrupt. The dwc3 driver needs to check the TRB status
associated with the request when reporting its status.
Note: this is only applicable to missed_isoc TRB completion status, but
the other status are also listed for completeness/documentation.
Fixes: 6d8a019614f3 ("usb: dwc3: gadget: check for Missed Isoc from event status") Cc: <stable@vger.kernel.org> Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/db2c80108286cfd108adb05bad52138b78d7c3a7.1650673655.git.Thinh.Nguyen@synopsys.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Make sure not to set run_stop bit or link state change request while
initiating soft-reset. Register read-modify-write operation may
unintentionally start the controller before the initialization completes
with its previous DCTL value, which can cause initialization failure.
The current driver logic checks against 0 to determine whether the
periodic tx/rx threshold settings are set, but we may get bogus values
from uninitialized variables if no device property is set. Properly
default these variables to 0.
Fixes: 938a5ad1d305 ("usb: dwc3: Check for ESS TX/RX threshold config") Cc: <stable@vger.kernel.org> Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/cccfce990b11b730b0dae42f9d217dc6fb988c90.1649727139.git.Thinh.Nguyen@synopsys.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If the PHY controller node has a "port" dwc3 tries to find an
extcon device even when "usb-role-switch" is present. This happens
because dwc3_get_extcon() sees that "port" node and then calls
extcon_find_edev_by_node() which will always return EPROBE_DEFER
in that case.
On the other hand, even if an extcon was present and dwc3_get_extcon()
was successful it would still be ignored in favor of "usb-role-switch".
Let's just first check if "usb-role-switch" is configured in the device
tree and directly use it instead and only try to look for an extcon
device otherwise.
Fixes: 8a0a13799744 ("usb: dwc3: Registering a role switch in the DRD code.") Cc: stable <stable@kernel.org> Signed-off-by: Sven Peter <sven@svenpeter.dev> Link: https://lore.kernel.org/r/20220411155300.9766-1-sven@svenpeter.dev Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If any function like UVC is deactivating gadget as part of composition
switch which results in not calling pullup enablement, it is not getting
enabled after switch to new composition due to this deactivation flag
not cleared. This results in USB enumeration not happening after switch
to new USB composition. Hence clear deactivation flag inside gadget
structure in configfs_composite_unbind() before switch to new USB
composition.
Signed-off-by: Vijayavardhan Vennapusa <vvreddy@codeaurora.org> Signed-off-by: Dan Vacura <w36195@motorola.com> Cc: stable <stable@kernel.org> Link: https://lore.kernel.org/r/20220413211038.72797-1-w36195@motorola.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
During the uvcg_video_pump() process, if an error occurs and
uvcg_queue_cancel() is called, the buffer queue will be cleared out, but
the current marker (queue->buf_used) of the active buffer (no longer
active) is not reset. On the next iteration of uvcg_video_pump() the
stale buf_used count will be used and the logic of min((unsigned
int)len, buf->bytesused - queue->buf_used) may incorrectly calculate a
nbytes size, causing an invalid memory access.
[80802.185460][ T315] configfs-gadget gadget: uvc: VS request completed
with status -18.
[80802.185519][ T315] configfs-gadget gadget: uvc: VS request completed
with status -18.
...
uvcg_queue_cancel() is called and the queue is cleared out, but the
marker queue->buf_used is not reset.
...
[80802.262328][ T8682] Unable to handle kernel paging request at virtual
address ffffffc03af9f000
...
...
[80802.263138][ T8682] Call trace:
[80802.263146][ T8682] __memcpy+0x12c/0x180
[80802.263155][ T8682] uvcg_video_pump+0xcc/0x1e0
[80802.263165][ T8682] process_one_work+0x2cc/0x568
[80802.263173][ T8682] worker_thread+0x28c/0x518
[80802.263181][ T8682] kthread+0x160/0x170
[80802.263188][ T8682] ret_from_fork+0x10/0x18
[80802.263198][ T8682] Code: a8c12829a88130cb a8c130
Fixes: d692522577c0 ("usb: gadget/uvc: Port UVC webcam gadget to use videobuf2 framework") Cc: <stable@vger.kernel.org> Signed-off-by: Dan Vacura <w36195@motorola.com> Link: https://lore.kernel.org/r/20220331184024.23918-1-w36195@motorola.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
All attempts to swap the roles timed out because the
completion was done without releasing the port lock. Fixing
that by releasing the lock before starting to wait for the
completion.
The role swapping completion variable is reused, so it needs
to be reinitialised every time. Otherwise it will be marked
as done after the first time it's used and completing
immediately.
Since commit ae8709b296d8 ("USB: core: Make do_proc_control() and
do_proc_bulk() killable") if a device has the USB_QUIRK_DELAY_CTRL_MSG
quirk set, it will temporarily block all other URBs (e.g. interrupts)
while sleeping due to a control.
This results in noticeable delays when, for example, a userspace usbfs
application is sending URB interrupts at a high rate to a keyboard and
simultaneously updates the lock indicators using controls. Interrupts
with direction set to IN are also affected by this, meaning that
delivery of HID reports (containing scancodes) to the usbfs application
is delayed as well.
This patch fixes the regression by calling msleep() while the device
mutex is unlocked, as was the case originally with usb_control_msg().
Fixes: ae8709b296d8 ("USB: core: Make do_proc_control() and do_proc_bulk() killable") Cc: stable <stable@kernel.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Tasos Sahanidis <tasos@tasossah.com> Link: https://lore.kernel.org/r/3e299e2a-13b9-ddff-7fee-6845e868bc06@tasossah.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
usb_put_dev shouldn't be called when uss720_probe succeeds because of
priv->usbdev. At the same time, priv->usbdev shouldn't be set to NULL
before destroy_priv in uss720_disconnect because usb_put_dev is in
destroy_priv.
Fix this by moving priv->usbdev = NULL after usb_put_dev.
Fixes: dcb4b8ad6a44 ("misc/uss720: fix memory leak in uss720_probe") Cc: stable <stable@kernel.org> Reviewed-by: Dongliang Mu <mudongliangabcd@gmail.com> Signed-off-by: Hangyu Hua <hbh25y@gmail.com> Link: https://lore.kernel.org/r/20220407024001.11761-1-hbh25y@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This register write to REG_INTF_CONFIG6 enables a spike filter that
is impacting the line and can prevent the I2C ACK to be seen by the
controller. So we don't test the return value.
The third call to `fwnode_property_read_u32` did not record
the return value, resulting in `channel_offstate` possibly
being assigned the wrong value.
Fixes: 56ca9db862bf ("iio: dac: Add support for the AD5592R/AD5593R ADCs/DACs") Signed-off-by: Zizhuang Deng <sunsetdzz@gmail.com> Link: https://lore.kernel.org/r/20220310125450.4164164-1-sunsetdzz@gmail.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The first U3 wake signal by the host may be lost if the USB 3 connection is
tunneled over USB4, with a runtime suspended USB4 host, and firmware
implemented connection manager.
Specs state the host must wait 100ms (tU3WakeupRetryDelay) before
resending a U3 wake signal if device doesn't respond, leading to U3 -> U0
link transition times around 270ms in the tunneled case.
Fixes: 0200b9f790b0 ("xhci: Wait until link state trainsits to U0 after setting USB_SS_PORT_LS_U0") Cc: stable@vger.kernel.org Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20220408134823.2527272-4-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
While rebooting, XHCI controller and its bus device will be shut down
in order by .shutdown callback. Stopping roothubs polling in
xhci_shutdown() can prevent XHCI driver from accessing port status
after its bus device shutdown.
Take PCIe XHCI controller as example, if XHCI driver doesn't stop roothubs
polling, XHCI driver may access PCIe BAR register for port status after
parent PCIe root port driver is shutdown and cause PCIe bus error.
[check shared hcd exist before stopping its roothub polling -Mathias]
Cc: stable@vger.kernel.org Signed-off-by: Henry Lin <henryl@nvidia.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20220408134823.2527272-3-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Alderlake has two XHCI controllers with PCI IDs 0x461e and 0x51ed. We
had previously added the quirk to default enable runtime PM for 0x461e,
now add it for 0x51ed as well.
pm_runtime_get_sync will increment pm usage counter
even it failed. Forgetting to putting operation will
result in reference leak here. We fix it by replacing
it with pm_runtime_resume_and_get to keep usage counter
balanced.
Fixes: 41a7426d25fa ("usb: xhci: tegra: Unlink power domain devices") Cc: stable <stable@vger.kernel.org> Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com> Link: https://lore.kernel.org/r/20220319023822.145641-1-zhangqilong3@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>