Since commit 8fffa0e3451a ("selftests/bpf: Normalize XDP section names in
selftests") the xdp_dummy.o's section name has changed to xdp. But some
tests are still using "section xdp_dummy", which make the tests failed.
Fix them by updating to the new section name.
Fixes: 8fffa0e3451a ("selftests/bpf: Normalize XDP section names in selftests") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Acked-by: Andrii Nakryiko <andrii@kernel.org> Link: https://lore.kernel.org/r/20220630062228.3453016-1-liuhangbin@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Testing shown that when a wq mode is setup to be dedicated and then torn
down and reconfigured to shared, the wq configured end up being dedicated
anyays. The root cause is when idxd_device_wqs_clear_state() gets called
during idxd_driver removal, idxd_wq_disable_cleanup() does not get called
vs when the wq driver is removed first. The check of wq state being
"enabled" causes the cleanup to be bypassed. However, idxd_driver->remove()
releases all wq drivers. So the wqs goes to "disabled" state and will never
be "enabled". By that point, the driver has no idea if the wq was
previously configured or clean. So force call idxd_wq_disable_cleanup() on
all wqs always to make sure everything gets cleaned up.
Reported-by: Tony Zhu <tony.zhu@intel.com> Tested-by: Tony Zhu <tony.zhu@intel.com> Fixes: 0dcfe41e9a4c ("dmanegine: idxd: cleanup all device related bits after disabling device") Signed-off-by: Dave Jiang <dave.jiang@intel.com> Co-developed-by: Fenghua Yu <fenghua.yu@intel.com> Signed-off-by: Fenghua Yu <fenghua.yu@intel.com> Link: https://lore.kernel.org/r/20220628230056.2527816-1-fenghua.yu@intel.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Commit dbad41e7bb5f ("dmaengine: qcom: bam_dma: check if the runtime pm enabled")
caused unbalanced pm_runtime_get/put() calls when the bam is
controlled remotely. This commit reverts it and just enables pm_runtime
in all cases, the clk_* functions already just nop when the clock is NULL.
Also clean up a bit by removing unnecessary bamclk null checks.
Suggested-by: Stephan Gerhold <stephan@gerhold.net> Fixes: dbad41e7bb5f ("dmaengine: qcom: bam_dma: check if the runtime pm enabled") Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org> Link: https://lore.kernel.org/r/20220629140559.118537-1-caleb.connolly@linaro.org Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
It seems that it is valid to have less than the requested number of
descriptors. But what is not valid and leads to subsequent errors is to
have zero descriptors. In that case, abort the probing.
Fixes: e1f7c9eee707 ("dmaengine: at_xdmac: creation of the atmel eXtended DMA Controller driver") Signed-off-by: Michael Walle <michael@walle.cc> Link: https://lore.kernel.org/r/20220526135111.1470926-1-michael@walle.cc Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The DEFINE_SPINLOCK() macro shouldn't be used for dynamically allocated
spinlocks. The lockdep warns about this and disables locking validator.
Fix the warning by making lock static.
INFO: trying to register non-static key.
The code is fine but needs lockdep annotation, or maybe
you didn't initialize this object before use?
turning off the locking correctness validator.
Hardware name: Radxa ROCK Pi 4C (DT)
Call trace:
dump_backtrace.part.0+0xcc/0xe0
show_stack+0x18/0x6c
dump_stack_lvl+0x8c/0xb8
dump_stack+0x18/0x34
register_lock_class+0x4a8/0x4cc
__lock_acquire+0x78/0x20cc
lock_acquire.part.0+0xe0/0x230
lock_acquire+0x68/0x84
_raw_spin_lock_irqsave+0x84/0xc4
add_desc+0x44/0xc0
pl330_get_desc+0x15c/0x1d0
pl330_prep_dma_cyclic+0x100/0x270
snd_dmaengine_pcm_trigger+0xec/0x1c0
dmaengine_pcm_trigger+0x18/0x24
...
This is another old BUG_ON() that just shouldn't exist (see also commit a382f8fee42c: "signal handling: don't use BUG_ON() for debugging").
In fact, as Matthew Wilcox points out, this condition shouldn't really
even result in a warning, since a negative id allocation result is just
a normal allocation failure:
"I wonder if we should even warn here -- sure, the caller is trying to
free something that wasn't allocated, but we don't warn for
kfree(NULL)"
and goes on to point out how that current error check is only causing
people to unnecessarily do their own index range checking before freeing
it.
This was noted by Itay Iellin, because the bluetooth HCI socket cookie
code does *not* do that range checking, and ends up just freeing the
error case too, triggering the BUG_ON().
The HCI code requires CAP_NET_RAW, and seems to just result in an ugly
splat, but there really is no reason to BUG_ON() here, and we have
generally striven for allocation models where it's always ok to just do
free(alloc());
even if the allocation were to fail for some random reason (usually
obviously that "random" reason being some resource limit).
Fixes: 88eca0207cf1 ("ida: simplified functions for id allocation") Reported-by: Itay Iellin <ieitayie@gmail.com> Suggested-by: Matthew Wilcox <willy@infradead.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The conditional block for variants with a second clock should have set
minItems, not maxItems, which was already 2. Since clock-names requires
two items, this typo should not have caused any problems.
Fixes: edd14218bd66 ("dt-bindings: dmaengine: Convert Allwinner A31 and A64 DMA to a schema") Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20220702031903.21703-1-samuel@sholland.org Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
It was found that some MediaTek SoCs are incompatible with this
change. Also, this register was mistakenly understood as it was
related to the 16550A register layout selection but, at least
on some IPs, if not all, it's related to something else unknown.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Fixes: 6f81fdded0d0 ("serial: 8250_mtk: Make sure to select the right FEATURE_SEL") Reported-by: "kernelci.org bot" <bot@kernelci.org> Link: https://lore.kernel.org/r/20220510122620.150342-1-angelogioacchino.delregno@collabora.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Reverts commit 888af2701db7 ("mm/memory-failure.c: fix race with changing
page compound again") because now we fetch the page refcount under
hugetlb_lock in try_memory_failure_hugetlb() so that the race check is no
longer necessary.
Link: https://lkml.kernel.org/r/20220408135323.1559401-4-naoya.horiguchi@linux.dev Signed-off-by: Naoya Horiguchi <naoya.horiguchi@nec.com> Suggested-by: Miaohe Lin <linmiaohe@huawei.com> Reviewed-by: Miaohe Lin <linmiaohe@huawei.com> Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Yang Shi <shy828301@gmail.com> Cc: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Set return value in rsp_buf alloc error path before going to
error handling.
drivers/misc/cardreader/rtsx_usb.c:639:6: warning: variable 'ret' is used uninitialized whenever 'if' condition is true [-Wsometimes-uninitialized]
if (!ucr->rsp_buf)
^~~~~~~~~~~~~
drivers/misc/cardreader/rtsx_usb.c:678:9: note: uninitialized use occurs here
return ret;
^~~
drivers/misc/cardreader/rtsx_usb.c:639:2: note: remove the 'if' if its condition is always false
if (!ucr->rsp_buf)
^~~~~~~~~~~~~~~~~~
drivers/misc/cardreader/rtsx_usb.c:622:9: note: initialize the variable 'ret' to silence this warning
int ret;
^
= 0
Fixes: 3776c7855985 ("misc: rtsx_usb: use separate command and response buffers") Reported-by: kernel test robot <lkp@intel.com> Cc: stable <stable@kernel.org> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org> Link: https://lore.kernel.org/r/20220701165352.15687-1-skhan@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
rtsx_usb uses same buffer for command and response. There could
be a potential conflict using the same buffer for both especially
if retries and timeouts are involved.
Use separate command and response buffers to avoid conflicts.
rtsx_usb driver allocates coherent dma buffer for urb transfers.
This buffer is passed to usb_bulk_msg() and usb core tries to
map already mapped buffer running into a dma mapping error.
xhci_hcd 0000:01:00.0: rejecting DMA map of vmalloc memory
WARNING: CPU: 1 PID: 279 at include/linux/dma-mapping.h:326 usb_ hcd_map_urb_for_dma+0x7d6/0x820
The revision of the imx-sdma IP that is in the i.MX8M series is the
same is that as that in the i.MX7 series but the imx7d MODULE_FIRMWARE
directive is wrapped in a condiditional which means it's not defined
when built for aarch64 SOC_IMX8M platforms and hence you get the
following errors when the driver loads on imx8m devices:
imx-sdma 302c0000.dma-controller: Direct firmware load for imx/sdma/sdma-imx7d.bin failed with error -2
imx-sdma 302c0000.dma-controller: external firmware not found, using ROM firmware
Add the SOC_IMX8M into the check so the firmware can load on i.MX8.
Fixes: 1474d48bd639 ("arm64: dts: imx8mq: Add SDMA nodes") Fixes: 941acd566b18 ("dmaengine: imx-sdma: Only check ratio on parts that support 1:1") Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Cc: stable@vger.kernel.org # v5.2+ Reviewed-by: Fabio Estevam <festevam@gmail.com> Link: https://lore.kernel.org/r/20220606161034.3544803-1-pbrobinson@gmail.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
66e4c8d95008 ("net: warn if transport header was not set") added
a check that triggers a warning in r8169, see [0].
The commit referenced in the Fixes tag refers to the change from
which the patch applies cleanly, there's nothing wrong with this
commit. It seems the actual issue (not bug, because the warning
is harmless here) was introduced with bdfa4ed68187
("r8169: use Giant Send").
When packets are not received, they aren't received on $host1_if, so the
message talking about the second host not receiving them is incorrect.
Fix it.
Fixes: d4deb01467ec ("selftests: forwarding: Add a test for FDB learning") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The first host interface has by default no interest in receiving packets
MAC DA de:ad:be:ef:13:37, so it might drop them before they hit the tc
filter and this might confuse the selftest.
Enable promiscuous mode such that the filter properly counts received
packets.
Fixes: d4deb01467ec ("selftests: forwarding: Add a test for FDB learning") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Tested-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
As mentioned in the blamed commit, flood_unicast_test() works by
checking the match count on a tc filter placed on the receiving
interface.
But the second host interface (host2_if) has no interest in receiving a
packet with MAC DA de:ad:be:ef:13:37, so its RX filter drops it even
before the ingress tc filter gets to be executed. So we will incorrectly
get the message "Packet was not flooded when should", when in fact, the
packet was flooded as expected but dropped due to an unrelated reason,
at some other layer on the receiving side.
Force h2 to accept this packet by temporarily placing it in promiscuous
mode. Alternatively we could either deliver to its MAC address or use
tcpdump_start, but this has the fewest complications.
This fixes the "flooding" test from bridge_vlan_aware.sh and
bridge_vlan_unaware.sh, which calls flood_test from the lib.
Fixes: 236dd50bf67a ("selftests: forwarding: Add a test for flooded traffic") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Tested-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
During a reset, there may have been transmits in flight that are no
longer valid and cannot be fulfilled. Resetting and clearing the
queues is insufficient; each skb also needs to be explicitly freed
so that upper levels are not left waiting for confirmation of a
transmit that will never happen. If this happens frequently enough,
the apparent backlog will cause TCP to begin "congestion control"
unnecessarily, culminating in permanently decreased throughput.
Fixes: d7c0ef36bde03 ("ibmvnic: Free and re-allocate scrqs when tx/rx scrqs change") Tested-by: Nick Child <nnac123@linux.ibm.com> Reviewed-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: Rick Lindsley <ricklind@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The USBH composed of EHCI and OHCI controllers needs the PHY clock to be
initialized first, before enabling (gating) them. The reverse is also
required when going to suspend.
So, add USBPHY clock as 1st entry in both controllers, so the USBPHY PLL
gets enabled 1st upon controller init. Upon suspend/resume, this also makes
the clock to be disabled/re-enabled in the correct order.
This fixes some IRQ storm conditions seen when going to low-power, due to
PHY PLL being disabled before all clocks are cleanly gated.
Fixes: 949a0c0dec85 ("ARM: dts: stm32: add USB Host (USBH) support to stm32mp157c") Fixes: db7be2cb87ae ("ARM: dts: stm32: use usbphyc ck_usbo_48m as USBH OHCI clock on stm32mp151") Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Referring to the note under USBH reset and clocks chapter of RM0436,
"In order to access USBH_OHCI registers it is necessary to activate the USB
clocks by enabling the PLL controlled by USBPHYC" (ck_usbo_48m).
The point is, when USBPHYC PLL is not enabled, OHCI register access
freezes the resume from STANDBY. It is the case when dual USBH is enabled,
instead of OTG + single USBH.
When OTG is probed, as ck_usbo_48m is USBO clock parent, then USBPHYC PLL
is enabled and OHCI register access is OK.
This patch adds ck_usbo_48m (provided by USBPHYC PLL) as clock of USBH
OHCI, thus USBPHYC PLL will be enabled and OHCI register access will be OK.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Clear VF MAC from parent PF and remove VF filter from VSI when both
conditions are true:
-VIRTCHNL_VF_OFFLOAD_USO is not used
-VM MAC was not set from PF level
It affects older version of IAVF and it allow them to change MAC
Address on VM, newer IAVF won't change their behaviour.
Previously it wasn't possible to change VF's MAC Address on VM
because there is flag on IAVF driver that won't allow to
change MAC Address if this address is given from PF driver.
Fixes: 155f0ac2c96b ("iavf: allow permanent MAC address to change") Signed-off-by: Norbert Zulinski <norbertx.zulinski@intel.com> Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Dropped packets caused by too large frames were not included in
dropped RX packets statistics.
Issue was caused by not reading the GL_RXERR1 register. That register
stores count of packet which was have been dropped due to too large
size.
Fix it by reading GL_RXERR1 register for each interface.
Repro steps:
Send a packet larger than the set MTU to SUT
Observe rx statists: ethtool -S <interface> | grep rx | grep -v ": 0"
Fixes: 41a9e55c89be ("i40e: add missing VSI statistics") Signed-off-by: Lukasz Cieplicki <lukaszx.cieplicki@intel.com> Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The recently added support for EFCH MMIO regions introduced a memory
leak in that code path. The leak is caused by the fact that
release_resource() merely removes the resource from the tree but does
not free its memory. We need to call release_mem_region() instead,
which does free the memory. As a nice side effect, this brings back
some symmetry between the legacy and MMIO paths.
Signed-off-by: Jean Delvare <jdelvare@suse.de> Reported-by: Yi Zhang <yi.zhang@redhat.com> Tested-by: Yi Zhang <yi.zhang@redhat.com> Reviewed-by: Terry Bowman <terry.bowman@amd.com> Tested-by: Terry Bowman <Terry.Bowman@amd.com> Fixes: 7c148722d074 ("i2c: piix4: Add EFCH MMIO support to region request and release") Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When a XSK pool gets mapped, xp_check_dma_contiguity() adds bit 0x1
to pages' DMA addresses that go in ascending order and at 4K stride.
The problem is that the bit does not get cleared before doing unmap.
As a result, a lot of warnings from iommu_dma_unmap_page() are seen
in dmesg, which indicates that lookups by iommu_iova_to_phys() fail.
Fixes: 2b43470add8c ("xsk: Introduce AF_XDP buffer allocation API") Signed-off-by: Ivan Malov <ivan.malov@oktetlabs.ru> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Magnus Karlsson <magnus.karlsson@intel.com> Link: https://lore.kernel.org/bpf/20220628091848.534803-1-ivan.malov@oktetlabs.ru Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Fix SoC detection for SAM9X60 SiPs:
SAM9X60D5M
SAM9X60D1G
SAM9X60D6K
Fixes: af3a10513cd6 ("drivers: soc: atmel: add per soc id and version match masks") Signed-off-by: Mihai Sain <mihai.sain@microchip.com> Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/20220616081344.1978664-1-claudiu.beznea@microchip.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The board has a microchip 24aa025e48 eeprom, which is a 2 Kbits memory,
so it's compatible with at24c02 not at24c32.
Also the size property is wrong, it's not 128 bytes, but 256 bytes.
Thus removing and leaving it to the default (256).
Fixes: 1e5f532c27371 ("ARM: dts: at91: sam9x60: add device tree for soc and board") Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com> Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/20220607090455.80433-1-eugen.hristev@microchip.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
"make dtbs_check" complains about the missing "-supply" suffix for
vdd_lvs1_2 which is clearly a typo, originally introduced in the
msm8994-smd-rpm.dtsi file and apparently later copied to
msm8992-xiaomi-libra.dts:
msm8992-lg-bullhead-rev-10/101.dtb: pm8994-regulators: 'vdd_lvs1_2'
does not match any of the regexes:
'.*-supply$', '^((s|l|lvs|5vs)[0-9]*)|(boost-bypass)|(bob)$', 'pinctrl-[0-9]+'
From schema: regulator/qcom,smd-rpm-regulator.yaml
msm8992-xiaomi-libra.dtb: pm8994-regulators: 'vdd_lvs1_2'
does not match any of the regexes:
'.*-supply$', '^((s|l|lvs|5vs)[0-9]*)|(boost-bypass)|(bob)$', 'pinctrl-[0-9]+'
From schema: regulator/qcom,smd-rpm-regulator.yaml
Reported-by: Rob Herring <robh@kernel.org> Cc: Konrad Dybcio <konrad.dybcio@somainline.org> Fixes: f3b2c99e73be ("arm64: dts: Enable onboard SDHCI on msm8992") Fixes: 0f5cdb31e850 ("arm64: dts: qcom: Add Xiaomi Libra (Mi 4C) device tree") Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com> Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20220627135938.2901871-1-stephan.gerhold@kernkonzept.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Some Allwinner SoCs have 2 pinctrls (PIO and R_PIO).
Previous implementation used absolute pin numbering and it was incorrect
for R_PIO pinctrl.
It's necessary to take into account the base pin number.
Fixes: 90be64e27621 ("pinctrl: sunxi: implement pin_config_set") Signed-off-by: Andrei Lalaev <andrey.lalaev@gmail.com> Reviewed-by: Samuel Holland <samuel@sholland.org> Link: https://lore.kernel.org/r/20220525190423.410609-1-andrey.lalaev@gmail.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
According to the IOMUXC_SW_PAD_CTL_PAD_UART2_RXD/TXD register define in
imx8mp RM, bit0 and bit3 are reserved, and the uart2 rx/tx pin should
enable the pull up, so need to set bit8 to 1. The original pinctl value
0x49 is incorrect and needs to be changed to 0x140, same as uart1 and
uart3.
Currently, when booting Linux on a imx28-evk board there is
no display activity.
Enable CONFIG_FB which is nowadays required for CONFIG_DRM_PANEL_LVDS,
CONFIG_DRM_PANEL_SIMPLE, CONFIG_DRM_PANEL_SEIKO_43WVF1G,
CONFIG_FB_MODE_HELPERS, CONFIG_BACKLIGHT_PWM, CONFIG_BACKLIGHT_GPIO,
CONFIG_FRAMEBUFFER_CONSOLE, CONFIG_LOGO, CONFIG_FONTS, CONFIG_FONT_8x8
and CONFIG_FONT_8x16.
Based on commit c54467482ffd ("ARM: imx_v6_v7_defconfig: enable fb").
Fixes: f611b1e7624c ("drm: Avoid circular dependencies for CONFIG_FB") Signed-off-by: Fabio Estevam <festevam@denx.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
It was noticed that on sdm845 after an MDSS suspend/resume cycle the
driver can not read HW_REV registers properly (they will return 0
instead). Chaning the "iface" clock from <&gcc GCC_DISP_AHB_CLK> to
<&dispcc DISP_CC_MDSS_AHB_CLK> fixes the issue.
The .set_jack_detect() codec component callback is invoked during card
registration, which happens when the machine driver is probed.
The issue is that this callback can race with the bus suspend/resume,
and IO timeouts can happen. This can be reproduced very easily if the
machine driver is 'blacklisted' and manually probed after the bus
suspends. The bus and codec need to be re-initialized using pm_runtime
helpers.
Previous contributions tried to make sure accesses to the bus during
the .set_jack_detect() component callback only happen when the bus is
active. This was done by changing the regcache status on a component
remove. This is however a layering violation, the regcache status
should only be modified on device probe, suspend and resume. The
component probe/remove should not modify how the device regcache is
handled. This solution also didn't handle all the possible race
conditions, and the RT700 headset codec was not handled.
This patch tries to resume the codec device before handling the jack
initializations. In case the codec has not yet been initialized,
pm_runtime may not be enabled yet, so we don't squelch the -EACCES
error code and only stop the jack information. When the codec reports
as attached, the jack initialization will proceed as usual.
BugLink: https://github.com/thesofproject/linux/issues/3643 Fixes: 7ad4d237e7c4a ('ASoC: rt711-sdca: Add RT711 SDCA vendor-specific driver') Fixes: 899b12542b089 ('ASoC: rt711: add snd_soc_component remove callback') Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by: Rander Wang <rander.wang@intel.com> Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com> Link: https://lore.kernel.org/r/20220606203752.144159-8-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The endianness flag is used on the CODEC side to specify an
ambivalence to endian, typically because it is lost over the hardware
link. This device receives audio over a SoundWire DAI and as such
should have endianness applied.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/20220504170905.332415-32-ckeepax@opensource.cirrus.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The endianness flag is used on the CODEC side to specify an
ambivalence to endian, typically because it is lost over the hardware
link. This device receives audio over a SoundWire DAI and as such
should have endianness applied.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/20220504170905.332415-31-ckeepax@opensource.cirrus.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
of_find_compatible_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
Add missing of_node_put() to avoid refcount leak.
Fixes: d850f3e5d296 ("ARM: meson: Add SMP bringup code for Meson8 and Meson8b") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://lore.kernel.org/r/20220512021611.47921-1-linmq006@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.2.1.2 describes the encoding of the
C/R (command/response) bit. Table 1 shows that the actual encoding of the
C/R bit is inverted if the associated frame is sent by the responder.
The referenced commit fixed here further broke the internal meaning of this
bit in the outgoing path by always setting the C/R bit regardless of the
frame type.
This patch fixes both by setting the C/R bit always consistently for
command (1) and response (0) frames and inverting it later for the
responder where necessary. The meaning of this bit in the debug output
is being preserved and shows the bit as if it was encoded by the initiator.
This reflects only the frame type rather than the encoded combination of
communication side and frame type.
Fixes: cc0f42122a7e ("tty: n_gsm: Modify CR,PF bit when config requester") Cc: stable@vger.kernel.org Signed-off-by: Daniel Starke <daniel.starke@siemens.com> Link: https://lore.kernel.org/r/20220218073123.2121-2-daniel.starke@siemens.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Clang static analysis reports this problem
ioctl.c:3333:8: warning: 3rd function call argument is an
uninitialized value
ret = exclop_start_or_cancel_reloc(fs_info,
cancel is only set in one branch of an if-check and is always used. So
initialize to false.
Fixes: 1a15eb724aae ("btrfs: use btrfs_get_dev_args_from_path in dev removal ioctls") Reviewed-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: Tom Rix <trix@redhat.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If memdup_user() fails the error handing will crash when it tries
to kfree() an error pointer. Just return directly because there is
no cleanup required.
Fixes: 1a15eb724aae ("btrfs: use btrfs_get_dev_args_from_path in dev removal ioctls") Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Once the uart_port->rs485->flag is set to SER_RS485_ENABLED, the port
should always work in RS485 mode. If users want the port to leave
RS485 mode, they need to call ioctl() to clear SER_RS485_ENABLED.
So here we shouldn't clear the RS485 bits in the shutdown().
Fixes: 927728a34f11 ("serial: sc16is7xx: Clear RS485 bits in the shutdown") Signed-off-by: Hui Wang <hui.wang@canonical.com> Link: https://lore.kernel.org/r/20220418094339.678144-1-hui.wang@canonical.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This ASSERT in xfs_rename is a) incorrect, because
(RENAME_WHITEOUT|RENAME_NOREPLACE) is a valid combination, and
b) unnecessary, because actual invalid flag combinations are already
handled at the vfs level in do_renameat2() before we get called.
So, remove it.
Reported-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Eric Sandeen <sandeen@redhat.com> Reviewed-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Darrick J. Wong <djwong@kernel.org> Fixes: 7dcf5c3e4527 ("xfs: add RENAME_WHITEOUT support") Reported-by: Ayushman Dutta <ayudutta@amazon.com> Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Use correct bittiming limits depending on device. For devices based on
USBcanII, Leaf M32C or Leaf i.MX28.
Fixes: 080f40a6fa28 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices") Fixes: b4f20130af23 ("can: kvaser_usb: add support for Kvaser Leaf v2 and usb mini PCIe") Fixes: f5d4abea3ce0 ("can: kvaser_usb: Add support for the USBcan-II family") Link: https://lore.kernel.org/all/20220603083820.800246-4-extja@kvaser.com Cc: stable@vger.kernel.org Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
[mkl: remove stray netlink.h include]
[mkl: keep struct can_bittiming_const kvaser_usb_flexc_bittiming_const in kvaser_usb_hydra.c] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The firmware of M32C based Leaf devices expects bittiming parameters
calculated for 16MHz clock. Since we use the actual clock frequency of
the device, the device may end up with wrong bittiming parameters,
depending on user requested parameters.
This regression affects M32C based Leaf devices with non-16MHz clock.
Fixes: a8b513b824e4 ("can: kvaser_usb: get CAN clock frequency from device") Link: https://lore.kernel.org/all/20220603083820.800246-3-extja@kvaser.com Cc: stable@vger.kernel.org Signed-off-by: Jimmy Assarsson <extja@kvaser.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
It was discovered that the Documentation lacks of a fundamental detail
on how to correctly change the MAX_FRAME_SIZE of the switch.
In fact if the MAX_FRAME_SIZE is changed while the cpu port is on, the
switch panics and cease to send any packet. This cause the mgmt ethernet
system to not receive any packet (the slow fallback still works) and
makes the device not reachable. To recover from this a switch reset is
required.
To correctly handle this, turn off the cpu ports before changing the
MAX_FRAME_SIZE and turn on again after the value is applied.
Fixes: f58d2598cf70 ("net: dsa: qca8k: implement the port MTU callbacks") Cc: stable@vger.kernel.org Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Link: https://lore.kernel.org/r/20220621151122.10220-1-ansuelsmth@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The platform device for the rng must be created much later in boot.
Otherwise it tries to connect to a parent that doesn't yet exist,
resulting in this splat:
This patch fixes the issue by doing the platform device creation inside
of machine_subsys_initcall.
Fixes: f3eac426657d ("powerpc/powernv: wire up rng during setup_arch") Cc: stable@vger.kernel.org Reported-by: Sachin Sant <sachinp@linux.ibm.com> Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Tested-by: Sachin Sant <sachinp@linux.ibm.com>
[mpe: Change "of node" to "platform device" in change log] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20220630121654.1939181-1-Jason@zx2c4.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In the CONFIG_MEMREGION=n case, memregion_free() is meant to be a static
inline. 0day reports:
In file included from drivers/cxl/core/port.c:4:
include/linux/memregion.h:19:6: warning: no previous prototype for
function 'memregion_free' [-Wmissing-prototypes]
Mark memregion_free() static.
Fixes: 33dd70752cd7 ("lib: Uplevel the pmem "region" ida to a global allocator") Reported-by: kernel test robot <lkp@intel.com> Reviewed-by: Alison Schofield <alison.schofield@intel.com> Link: https://lore.kernel.org/r/165601455171.4042645.3350844271068713515.stgit@dwillia2-xfh Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Instead of passing an extra bool argument to pm_runtime_release_supplier(),
make its callers take care of triggering a runtime-suspend of the
supplier device as needed.
No expected functional impact.
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: 5.1+ <stable@vger.kernel.org> # 5.1+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Notifier calling chain uses priority to determine the execution
order of the notifiers or listeners registered to the chain.
PCI bus device hot add utilizes the notification mechanism.
The current code sets low priority (INT_MIN) to Intel
dmar_pci_bus_notifier and postpones DMAR decoding after adding
new device into IOMMU. The result is that struct device pointer
cannot be found in DRHD search for the new device's DMAR/IOMMU.
Subsequently, the device is put under the "catch-all" IOMMU
instead of the correct one. This could cause system hang when
device TLB invalidation is sent to the wrong IOMMU. Invalidation
timeout error and hard lockup have been observed and data
inconsistency/crush may occur as well.
This patch fixes the issue by setting a positive priority(1) for
dmar_pci_bus_notifier while the priority of IOMMU bus notifier
uses the default value(0), therefore DMAR decoding will be in
advance of DRHD search for a new device to find the correct IOMMU.
Following is a 2-step example that triggers the bug by simulating
PCI device hot add behavior in Intel Sapphire Rapids server.
elf_validity_check() checks ELF headers for errors and ELF Spec.
compliance and if any of them fail it returns -ENOEXEC from all of
these error paths. Almost all of them don't print any messages.
When elf_validity_check() returns an error, load_module() prints an
error message without error code. It is hard to determine why the
module ELF structure is invalid, even if load_module() prints the
error code which is -ENOEXEC in all of these cases.
Change to print useful error messages from elf_validity_check() to
clearly say what went wrong and why the ELF validity checks failed.
Remove the load_module() error message which is no longer needed.
This patch includes changes to fix build warns on 32-bit platforms:
warning: format '%llu' expects argument of type 'long long unsigned int',
but argument 3 has type 'Elf32_Off' {aka 'unsigned int'} Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: Luis Chamberlain <mcgrof@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
There's a locking issue with the per-netns list of calls in rxrpc. The
pieces of code that add and remove a call from the list use write_lock()
and the calls procfile uses read_lock() to access it. However, the timer
callback function may trigger a removal by trying to queue a call for
processing and finding that it's already queued - at which point it has a
spare refcount that it has to do something with. Unfortunately, if it puts
the call and this reduces the refcount to 0, the call will be removed from
the list. Unfortunately, since the _bh variants of the locking functions
aren't used, this can deadlock.
================================
WARNING: inconsistent lock state
5.18.0-rc3-build4+ #10 Not tainted
--------------------------------
inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
ksoftirqd/2/25 [HC0[0]:SC1[1]:HE1:SE0] takes: ffff888107ac4038 (&rxnet->call_lock){+.?.}-{2:2}, at: rxrpc_put_call+0x103/0x14b
{SOFTIRQ-ON-W} state was registered at:
...
Possible unsafe locking scenario:
1 lock held by ksoftirqd/2/25:
#0: ffff8881008ffdb0 ((&call->timer)){+.-.}-{0:0}, at: call_timer_fn+0x5/0x23d
Changes
=======
ver #2)
- Changed to using list_next_rcu() rather than rcu_dereference() directly.
Fixes: 17926a79320a ("[AF_RXRPC]: Provide secure RxRPC sockets for use by userspace and kernel both") Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
There are cases where a context synchronization event is necessary
between an IRQ being raised and being handled, and there are races such
that we cannot rely upon the exception entry being subsequent to the
interrupt being raised. To fix this, we place an ISB between a read of
IAR and the subsequent invocation of an IRQ handler.
When EOI mode 1 is in use, we need to EOI an interrupt prior to invoking
its handler, and we have a write to EOIR for this. As this write to EOIR
requires an ISB, and this is provided by the gic_write_eoir() helper, we
omit the usual ISB in this case, with the logic being:
| if (static_branch_likely(&supports_deactivate_key))
| gic_write_eoir(irqnr);
| else
| isb();
This is somewhat opaque, and it would be a little clearer if there were
an unconditional ISB, with only the write to EOIR being conditional,
e.g.
| if (static_branch_likely(&supports_deactivate_key))
| write_gicreg(irqnr, ICC_EOIR1_EL1);
|
| isb();
This patch rewrites the code that way, with this logic factored into a
new helper function with comments explaining what the ISB is for, as
were originally laid out in commit:
39a06b67c2c1256b ("irqchip/gic: Ensure we have an ISB between ack and ->handle_irq")
Note that since then, we removed the IAR polling in commit:
For consistency, other portions of the driver are made to manipulate
EOIR using write_gicreg() and explcit ISBs, and the gic_write_eoir()
helper function is removed.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Cc: Marc Zyngier <maz@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20220513133038.226182-3-mark.rutland@arm.com Cc: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
There are cases where a context synchronization event is necessary
between an IRQ being raised and being handled, and there are races such
that we cannot rely upon the exception entry being subsequent to the
interrupt being raised.
We identified and fixes this for regular IRQs in commit:
39a06b67c2c1256b ("irqchip/gic: Ensure we have an ISB between ack and ->handle_irq")
Unfortunately, we forgot to do the same for psuedo-NMIs when support for
those was added in commit:
If an opcode handler semi-reliably returns -EAGAIN, io_wq_submit_work()
might continue busily hammer the same handler over and over again, which
is not ideal. The -EAGAIN handling in question was put there only for
IOPOLL, so restrict it to IOPOLL mode only where there is no other
recourse than to retry as we cannot wait.
Fixes: def596e9557c9 ("io_uring: support for IO polling") Signed-off-by: Pavel Begunkov <asml.silence@gmail.com> Link: https://lore.kernel.org/r/f168b4f24181942f3614dd8ff648221736f572e6.1652433740.git.asml.silence@gmail.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
We should not access skb buffer data anymore after hci_recv_frame was
called.
[ 39.634809] BUG: KASAN: use-after-free in btmtksdio_recv_event+0x1b0
[ 39.634855] Read of size 1 at addr ffffff80cf28a60d by task kworker
[ 39.634962] Call trace:
[ 39.634974] dump_backtrace+0x0/0x3b8
[ 39.634999] show_stack+0x20/0x2c
[ 39.635016] dump_stack_lvl+0x60/0x78
[ 39.635040] print_address_description+0x70/0x2f0
[ 39.635062] kasan_report+0x154/0x194
[ 39.635079] __asan_report_load1_noabort+0x44/0x50
[ 39.635099] btmtksdio_recv_event+0x1b0/0x1c4
[ 39.635129] btmtksdio_txrx_work+0x6cc/0xac4
[ 39.635157] process_one_work+0x560/0xc5c
[ 39.635177] worker_thread+0x7ec/0xcc0
[ 39.635195] kthread+0x2d0/0x3d0
[ 39.635215] ret_from_fork+0x10/0x20
[ 39.635247] Allocated by task 0:
[ 39.635260] (stack is not available)
[ 39.635281] Freed by task 2392:
[ 39.635295] kasan_save_stack+0x38/0x68
[ 39.635319] kasan_set_track+0x28/0x3c
[ 39.635338] kasan_set_free_info+0x28/0x4c
[ 39.635357] ____kasan_slab_free+0x104/0x150
[ 39.635374] __kasan_slab_free+0x18/0x28
[ 39.635391] slab_free_freelist_hook+0x114/0x248
[ 39.635410] kfree+0xf8/0x2b4
[ 39.635427] skb_free_head+0x58/0x98
[ 39.635447] skb_release_data+0x2f4/0x410
[ 39.635464] skb_release_all+0x50/0x60
[ 39.635481] kfree_skb+0xc8/0x25c
[ 39.635498] hci_event_packet+0x894/0xca4 [bluetooth]
[ 39.635721] hci_rx_work+0x1c8/0x68c [bluetooth]
[ 39.635925] process_one_work+0x560/0xc5c
[ 39.635951] worker_thread+0x7ec/0xcc0
[ 39.635970] kthread+0x2d0/0x3d0
[ 39.635990] ret_from_fork+0x10/0x20
[ 39.636021] The buggy address belongs to the object at ffffff80cf28a600
which belongs to the cache kmalloc-512 of size 512
[ 39.636039] The buggy address is located 13 bytes inside of
512-byte region [ffffff80cf28a600, ffffff80cf28a800)
Fixes: 9aebfd4a2200 ("Bluetooth: mediatek: add support for MediaTek MT7663S and MT7668S SDIO devices") Co-developed-by: Yake Yang <yake.yang@mediatek.com> Signed-off-by: Yake Yang <yake.yang@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Concurrent operations from events on le_{accept,resolv}_list are
currently unprotected by hdev->lock.
Most existing code do already protect the lists with that lock.
This can be observed in hci_debugfs and hci_sync.
Add the protection for these events too.
Fixes: b950aa88638c ("Bluetooth: Add definitions and track LE resolve list modification") Fixes: 0f36b589e4ee ("Bluetooth: Track LE white list modification via HCI commands") Signed-off-by: Niels Dossche <dossche.niels@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
We encountered a kernel panic issue that callback data will be NULL when
it's using in ovl irq handler. There is a timing issue between
mtk_disp_ovl_irq_handler() and mtk_ovl_disable_vblank().
To resolve this issue, we use the flow to register/unregister vblank cb:
- Register callback function and callback data when crtc creates.
- Unregister callback function and callback data when crtc destroies.
With this solution, we can assure callback data will not be NULL when
vblank is disable.
CMDQ is used to update display register in vblank period, so
it should be execute in next 2 vblank. One vblank interrupt
before send message (occasionally) and one vblank interrupt
after cmdq done. If it fail to execute in next 3 vblank,
tiemout happen.
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org> Signed-off-by: jason-jh.lin <jason-jh.lin@mediatek.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In mailbox rx_callback, it pass struct mbox_client to callback
function, but it could not map back to mtk_drm_crtc instance
because struct cmdq_client use a pointer to struct mbox_client:
rx_callback is a standard mailbox callback mechanism and could cover the
function of proprietary cmdq_task_cb, so use the standard one instead of
the proprietary one.
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org> Signed-off-by: jason-jh.lin <jason-jh.lin@mediatek.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The vma destruction code was using an unlocked advisory check for
drm_mm_node_allocated() to avoid racing with eviction code unbinding
the vma.
This is very fragile and prohibits the dereference of non-refcounted
pointers of dying vmas after a call to __i915_vma_unbind(). It also
prohibits the dereference of vma->obj of refcounted pointers of
dying vmas after a call to __i915_vma_unbind(), since even if a
refcount is held on the vma, that won't guarantee that its backing
object doesn't get destroyed.
So introduce an unbind under the vm mutex at object destroy time,
removing all weak references of the vma and its object from the
object vma list and from the vm bound list.
gsmtty_write() does not prevent the user to use the full fifo size of 4096
bytes as allocated in gsm_dlci_alloc(). However, gsmtty_write_room() tries
to limit the return value by 'TX_SIZE' and returns a negative value if the
fifo has more than 'TX_SIZE' bytes stored. This is obviously wrong as
'TX_SIZE' is defined as 512.
Define 'TX_SIZE' to the fifo size and use it accordingly for allocation to
keep the current behavior. Return the correct remaining size of the fifo in
gsmtty_write_room() via kfifo_avail().
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline") Cc: stable@vger.kernel.org Signed-off-by: Daniel Starke <daniel.starke@siemens.com> Link: https://lore.kernel.org/r/20220504081733.3494-3-daniel.starke@siemens.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Set the FEATURE_SEL at probe time to make sure that BIT(0) is enabled:
this guarantees that when the port is configured as AP UART, the
right register layout is interpreted by the UART IP.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20220427132328.228297-3-angelogioacchino.delregno@collabora.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
'size' may be used uninitialized in gsm_dlci_modem_output() if called with
an adaption that is neither 1 nor 2. The function is currently only called
by gsm_modem_upd_via_data() and only for adaption 2.
Properly handle every invalid case by returning -EINVAL to silence the
compiler warning and avoid future regressions.
Fixes: c19ffe00fed6 ("tty: n_gsm: fix invalid use of MSC in advanced option") Cc: stable@vger.kernel.org Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Daniel Starke <daniel.starke@siemens.com> Link: https://lore.kernel.org/r/20220425104726.7986-1-daniel.starke@siemens.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.6.3.7 states that the Modem Status
Command (MSC) shall only be used if the basic option was chosen.
The current implementation uses MSC frames even if advanced option was
chosen to inform the peer about modem line state updates. A standard
conform peer may choose to discard these frames in advanced option mode.
Furthermore, gsmtty_modem_update() is not part of the 'tty_operations'
functions despite its name.
Rename gsmtty_modem_update() to gsm_modem_update() to clarify this. Split
its function into gsm_modem_upd_via_data() and gsm_modem_upd_via_msc()
depending on the encoding and adaption. Introduce gsm_dlci_modem_output()
as adaption of gsm_dlci_data_output() to encode and queue empty frames in
advanced option mode. Use it in gsm_modem_upd_via_data().
gsm_modem_upd_via_msc() is based on the initial gsmtty_modem_update()
function which used only MSC frames to update modem states.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline") Cc: stable@vger.kernel.org Signed-off-by: Daniel Starke <daniel.starke@siemens.com> Link: https://lore.kernel.org/r/20220422071025.5490-2-daniel.starke@siemens.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
There is a race condition between memory_failure_hugetlb() and hugetlb
free/demotion, which causes setting PageHWPoison flag on the wrong page.
The one simple result is that wrong processes can be killed, but another
(more serious) one is that the actual error is left unhandled, so no one
prevents later access to it, and that might lead to more serious results
like consuming corrupted data.
Think about the below race window:
CPU 1 CPU 2
memory_failure_hugetlb
struct page *head = compound_head(p);
hugetlb page might be freed to
buddy, or even changed to another
compound page.
get_hwpoison_page -- page is not what we want now...
The current code first does prechecks roughly and then reconfirms after
taking refcount, but it's found that it makes code overly complicated,
so move the prechecks in a single hugetlb_lock range.
A newly introduced function, try_memory_failure_hugetlb(), always takes
hugetlb_lock (even for non-hugetlb pages). That can be improved, but
memory_failure() is rare in principle, so should not be a big problem.
Link: https://lkml.kernel.org/r/20220408135323.1559401-2-naoya.horiguchi@linux.dev Fixes: 761ad8d7c7b5 ("mm: hwpoison: introduce memory_failure_hugetlb()") Signed-off-by: Naoya Horiguchi <naoya.horiguchi@nec.com> Reported-by: Mike Kravetz <mike.kravetz@oracle.com> Reviewed-by: Miaohe Lin <linmiaohe@huawei.com> Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com> Cc: Yang Shi <shy828301@gmail.com> Cc: Dan Carpenter <dan.carpenter@oracle.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Patch series "A few fixup patches for memory failure", v2.
This series contains a few patches to fix the race with changing page
compound page, make non-LRU movable pages unhandlable and so on. More
details can be found in the respective changelogs.
There is a race window where we got the compound_head, the hugetlb page
could be freed to buddy, or even changed to another compound page just
before we try to get hwpoison page. Think about the below race window:
CPU 1 CPU 2
memory_failure_hugetlb
struct page *head = compound_head(p);
hugetlb page might be freed to
buddy, or even changed to another
compound page.
get_hwpoison_page -- page is not what we want now...
If this race happens, just bail out. Also MF_MSG_DIFFERENT_PAGE_SIZE is
introduced to record this event.
[akpm@linux-foundation.org: s@/**@/*@, per Naoya Horiguchi]
Link: https://lkml.kernel.org/r/20220312074613.4798-1-linmiaohe@huawei.com Link: https://lkml.kernel.org/r/20220312074613.4798-2-linmiaohe@huawei.com Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Acked-by: Naoya Horiguchi <naoya.horiguchi@nec.com> Cc: Tony Luck <tony.luck@intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Yang Shi <shy828301@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When the hwpoison page meets the filter conditions, it should not be
regarded as successful memory_failure() processing for mce handler, but
should return a distinct value, otherwise mce handler regards the error
page has been identified and isolated, which may lead to calling
set_mce_nospec() to change page attribute, etc.
Here memory_failure() return -EOPNOTSUPP to indicate that the error
event is filtered, mce handler should not take any action for this
situation and hwpoison injector should treat as correct.
Link: https://lkml.kernel.org/r/20220223082135.2769649-1-luofei@unicloud.com Signed-off-by: luofei <luofei@unicloud.com> Acked-by: Borislav Petkov <bp@suse.de> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Naoya Horiguchi <naoya.horiguchi@nec.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tony Luck <tony.luck@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Patch series "mm/hwpoison: fix unpoison_memory()", v4.
The main purpose of this series is to sync unpoison code to recent
changes around how hwpoison code takes page refcount. Unpoison should
work or simply fail (without crash) if impossible.
The recent works of keeping hwpoison pages in shmem pagecache introduce
a new state of hwpoisoned pages, but unpoison for such pages is not
supported yet with this series.
It seems that soft-offline and unpoison can be used as general purpose
page offline/online mechanism (not in the context of memory error). I
think that we need some additional works to realize it because currently
soft-offline and unpoison are assumed not to happen so frequently (print
out too many messages for aggressive usecases). But anyway this could
be another interesting next topic.
Originally mf_mutex is introduced to serialize multiple MCE events, but
it is not that useful to allow unpoison to run in parallel with
memory_failure() and soft offline. So apply mf_mutex to soft offline
and unpoison. The memory failure handler and soft offline handler get
simpler with this.
Link: https://lkml.kernel.org/r/20211115084006.3728254-1-naoya.horiguchi@linux.dev Link: https://lkml.kernel.org/r/20211115084006.3728254-2-naoya.horiguchi@linux.dev Signed-off-by: Naoya Horiguchi <naoya.horiguchi@nec.com> Reviewed-by: Yang Shi <shy828301@gmail.com> Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com> Cc: David Hildenbrand <david@redhat.com> Cc: Ding Hui <dinghui@sangfor.com.cn> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Oscar Salvador <osalvador@suse.de> Cc: Peter Xu <peterx@redhat.com> Cc: Tony Luck <tony.luck@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Initialize debugfs_entry to its semi-magical -ENOENT value when the VM
is created. KVM's teardown when VM creation fails is kludgy and calls
kvm_uevent_notify_change() and kvm_destroy_vm_debugfs() even if KVM never
attempted kvm_create_vm_debugfs(). Because debugfs_entry is zero
initialized, the IS_ERR() checks pass and KVM derefs a NULL pointer.
Fixes: a44a4cc1c969 ("KVM: Don't create VM debugfs files outside of the VM directory") Cc: stable@vger.kernel.org Cc: Marc Zyngier <maz@kernel.org> Cc: Oliver Upton <oupton@google.com> Reported-by: syzbot+df6fbbd2ee39f21289ef@syzkaller.appspotmail.com Signed-off-by: Sean Christopherson <seanjc@google.com> Reviewed-by: Oliver Upton <oupton@google.com>
Message-Id: <20220415004622.2207751-1-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Currently, we use btrfs_inode_{lock,unlock}() to grant an exclusive
writeback of the relocation data inode in
btrfs_zoned_data_reloc_{lock,unlock}(). However, that can cause a deadlock
in the following path.
Thread A takes btrfs_inode_lock() and waits for metadata reservation by
e.g, waiting for writeback:
The deadlock is caused by relying on the vfs_inode's lock. By using it, we
introduced unnecessary exclusion of writeback and
btrfs_prealloc_file_range(). Also, the lock at this point is useless as we
don't have any dirty pages in the inode yet.
Introduce fs_info->zoned_data_reloc_io_lock and use it for the exclusive
writeback.
Fixes: 35156d852762 ("btrfs: zoned: only allow one process to add pages to a relocation inode") CC: stable@vger.kernel.org # 5.16.x: 869f4cdc73f9: btrfs: zoned: encapsulate inode locking for zoned relocation CC: stable@vger.kernel.org # 5.16.x CC: stable@vger.kernel.org # 5.17 Cc: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Encapsulate the inode lock needed for serializing the data relocation
writes on a zoned filesystem into a helper.
This streamlines the code reading flow and hides special casing for
zoned filesystems.
Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>