Hans Verkuil [Sun, 27 Aug 2006 22:22:15 +0000 (19:22 -0300)]
V4L/DVB (4548): Better temporal filter handling.
Adjust temporal filter if necessary. The problem with the temporal
filter is that it works well with full resolution capturing, but
not when the capture window is scaled (the filter introduces
a ghosting effect). So if the capture window changed, and there is
no updated filter value, then the filter is set depending on whether
the new window is full resolution or not.
For full resolution a setting of 8 really improves the video
quality, especially if the original video quality is suboptimal.
Also report VBI Format in VIDIOC_LOG_STATUS, it was missing.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hans Verkuil [Sat, 26 Aug 2006 08:00:12 +0000 (05:00 -0300)]
V4L/DVB (4547): Add YUV HM12 and VBI IVTV format documentation.
README.hm12: documentation on the HM12 YUV format used by the cx23415/6 chip.
README.vbi: documentation on the V4L2_MPEG_STREAM_VBI_FMT_IVTV VBI format
used in MPEG streams.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Trent Piepho [Fri, 25 Aug 2006 01:43:45 +0000 (22:43 -0300)]
V4L/DVB (4533): Tda9887: add configuration setting for L standard PLL gating
Add a tuner config parameter for TDA9887, default_pll_gating_18, that
changes the L standard PLL gating value from 36% to 0% (datasheet says
0%, tda9887 code says 18%).
Turn this on for Microtune 4049FM5, as recomended by tuner datasheet.
Jochen Issing [Sat, 19 Aug 2006 19:03:21 +0000 (16:03 -0300)]
V4L/DVB (4528): PATCH: Club 3D zap250mini
After some structural changes, here comes the updated patch for the Club 3D
zap250mini USB dvb device.
Adding support for a WideView-based device with a different "COLD" ID.
V4L/DVB (4518): Allow manually selecting the proper helper drivers
There are several boards on V4L that can work with several different
helper modules for audio/video encoding/decoding and similar stuff.
This patch adds the capability of choicing between autoselecting the
pertinent helper modules for each driver, or to manually selecting
them. Acked-by: Michael Krufky <mkrufky@linuxtv.org> Acked-by: Mike Isely <isely@pobox.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L/DVB (4516): Split audio/video encoders/decoders from main drivers
Several audio/video encoders/decoders were just bound as if they were
part of the core driver.
In fact, they are generic enough to be used by other drivers as well,
since they use I2C event bus to communicate.
Several audio decoders were just bound as if they were part of
bttv driver. In fact, they are generic enough to be used by other
drivers as well, since they use I2C event bus to communicate.
Eric Sesterhenn [Mon, 21 Aug 2006 13:36:36 +0000 (10:36 -0300)]
V4L/DVB (4510): Fix signedness error in drivers/media/video/vivi.c
when checking the -Wextra signedness warnings issued by gcc 4.1
I came across this one:
drivers/media/video/vivi.c:1001: warning: comparison of unsigned expression < 0 is always false
Since videobuf_reqbufs() returns negative values on errors the current
code does no real error checking since gcc removes the comparison.
This patch fixes this issue by making ret a normal, signed integer.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Several changes at register stuff were done since commit b45009b0288a96a3458f4f8e93cb776678d41875, but I've forgot
to add the copyright line for this. Those changes allowed
cx88 to have multiple tuners, allowing it to support hardware with
separated radio and video tuners. It also allows binding a tuner to an
specific i2c address.
The Coverity checker spotted the following two array overflows.
Registers 0xcc and 0xdc were cached on reg[] array, with only 128 elements,
instead of 256.
V4L/DVB (4504): Enable audio DMA restart on channel change even when cx88-alsa is compiled
cx88-alsa can be compiled in (in distro built kernels, for example), but
not used. In those cases, the audio DMA restart is needed for proper sound
on NICAM channels.
This patch enables the DMA restart even with ALSA, but the functions now
check if cx88-alsa is really active.
V4L/DVB (4501): Add support for knc one dvb-s plus with 1894:0011
Apparently there are two types of knc1 dvb-s plus cards with different tuners
(as for the knc1 dvb-s ones). This patch adds support for those cards with
subsystem id 1894:0011.
Successfully tested by: Benjamin Weber <benny1990@gmail.com>
Signed-off-by: Christoph Pfister <christophpfister@gmail.com> Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Chris Pascoe [Thu, 10 Aug 2006 06:22:21 +0000 (03:22 -0300)]
V4L/DVB (4497): Reset USB part of DViCO Dual Digital during PCI driver attach
If the FX2 does not reset properly during reboot, it can present an
invalid USB device ID and fail to attach. Prevent this situation
from occuring by resetting the USB part of the card when the PCI part
probes.
Also fix the GPIO configurations so that analog capture will not
inadvertantly reset the USB part.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Chris Pascoe [Thu, 10 Aug 2006 06:17:16 +0000 (03:17 -0300)]
V4L/DVB (4495): Fix "no data from ZL10353 based USB tuner" problem
Force parallel transport stream output on the ZL10353 attached to a
bluebird device.
Addresses the problem where a frontend lock was observed, but no MPEG
transport data was received.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
dvb_frontend_detach() used invalid config option CONFIG_DVB_DETACH,
so dvb_frontend_detach() did not call symbol_put_addr().
Replaced CONFIG_DVB_DETACH by CONFIG_DVB_CORE_ATTACH.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
drivers/media/video/pvrusb2/pvrusb2-i2c-cmd-v4l2.c: In function 'set_standard':
drivers/media/video/pvrusb2/pvrusb2-i2c-cmd-v4l2.c:33: warning: format '%llx' expects type 'long long unsigned int', but argument 2 has type 'v4l2_std_id'
Andrew Morton [Tue, 8 Aug 2006 13:52:22 +0000 (10:52 -0300)]
V4L/DVB (4484): Git-dvb: cadet build fix
drivers/media/radio/radio-cadet.c: In function 'cadet_do_ioctl':
drivers/media/radio/radio-cadet.c:362: warning: implicit declaration of function 'KERNEL_VERSION'
Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Dave Jones [Mon, 7 Aug 2006 16:18:56 +0000 (13:18 -0300)]
V4L/DVB (4480): Remove null chars from dvb names
DVB null terminates its device names, which seems odd, and should be
unnecessary. Acked-by: Alan Cox <alan@redhat.com> Signed-off-by: Dave Jones <davej@redhat.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L/DVB (4479): LNB voltage control was inverted for the benefit of geniatech cards on Kworld
1) It sets LNBDCPol differently based on the card type. Now it should
work properly for both the kworld and geniatech cards.
2) It stops returning an error for the SEC_VOLTAGE_OFF voltage command
(the cx88-dvb level handles the actual voltage on/off, but it still
passes the ioctl down to the cx24123 level, which previously rejected
the OFF as invalid so the ioctl would report failure)
Acked-by: Manu Abraham <manu@linuxtv.org> Signed-off-by: Yeasah Pell <yeasah@schwide.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L/DVB (4477): Improve hardware algorithm by setting the appropriate registers
Hardware algorithm needs to be configured to:
1) Increase timeout constants, to detect weaker signals;
2) do a wider zigzag search. Acked-by: Manu Abraham <manu@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Tested on x64 with a bttv board. Most Get ioctls are fixed. The only
non-completely working one is VIDIOCGAUDIO. All other IOR ioctls give the
same results on x86_64 and i386 architectures.
Thanks to Alastair Poole <netstar@gatheringofgray.com> for part of this
patch and tests on ppc64.
Signed-off-by: Alastair Poole <netstar@gatheringofgray.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Thomas Rokamp and others are reporting:
"I have now with success extracted a working firmware for the 93004 rev. C1A2."
This patch increments the firmware version to 2.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Flynn Marquardt found out that there is problem with the new dib3000mc-driver
when using with the real dib3000mc. It resulted in a segfault.
Fixed two things: use the correct I2C address and do not attach a tuner, when
the demod was previously failing.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
removing the dib3000-common-module. The common stuff is not common anymore - it will be only used by the 3000mb-driver.
A new 3000mc/p-driver will be added which will share common stuff with dib7000.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Sergei Haller [Sun, 14 May 2006 13:47:21 +0000 (10:47 -0300)]
V4L/DVB (4453): [PATCH] dibcom mod3000p + mt2060 -- remote control
+ Added support for the remote control shipped with the pen drive size
DVB-T receiver
[ID 10b8:0bc7 DiBcom DiBcom USB2.0 DVB-T reference design (MOD3000P)]
Signed-off-by: Sergei Haller <sergei@sergei-haller.de> Signed-off-by: Patrick Boettcher <pb@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L/DVB (4451): MT2060: IF1 Offset from EEPROM, several updates
- AGC gain set to 3
- The tuning sequence has been changed to match the DibCom driver ( from I2C
spy captures )
- For LITE-ON adapters : The IF1 frequency is now tuned according to the
calibration values stored in EEPROM.
- some coding style fixes for newly added mt2060
- moved agc-config from fixed values in dib3000mc to configurable ones
- whitespace clean-ups for usb-id-file
Signed-off-by: Patrick Boettcher <pb@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Tue, 8 Aug 2006 18:48:08 +0000 (15:48 -0300)]
V4L/DVB (4439): Whitespace cleanups for cx88-dvb and saa7134-dvb
This patch cleans up some whitespace problems after the dvb_attach changes
in cx88-dvb.c and saa7134-dvb.c, and converts some capitalized i2c address
constants to lowercase.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Tue, 8 Aug 2006 18:48:08 +0000 (15:48 -0300)]
V4L/DVB (4438): Fix dvb_pll_attach for nxt2004-based cards
The test in dvb-pll to see if a tuner's PLL responds when attaching fails
on NXT2004 based boards before the firmware is loaded.
This patch allows us to avoid this test by not passing an I2C bus handle to
the dvb_pll_attach routine, just as Chris Pascoe has done for MT352 and
ZL10353 based boards when used in cx88-dvb.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Chris Pascoe [Tue, 8 Aug 2006 18:48:08 +0000 (15:48 -0300)]
V4L/DVB (4436): Dvb-pll support for MT352/ZL10353 based tuners.
Typical wiring of MT352 and ZL10353 based tuners differs from dvb-pll's
expectation that the PLL is directly accessible. On these boards, the
PLL is actually hidden behind the demodulator, and as such can only be
accessed via the demodulator's interface. It was failing to communicate
with the PLL during an attach test and subsequently not connecting the
tuner ops.
By passing a NULL I2C bus handle to dvb_pll_attach, this accessibility
check can be bypassed. Do this for the affected boards. Also fix a
possible NULL dereference at sleep time, which would otherwise be
exposed by this change.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au> Acked-by: Andrew de Quincey <adq_dvb@lidskialf.net> Acked-by: Manu Abraham <manu@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The tda826x detection was (correctly) cleaned up earlier, but unfortunately
changing the number of received i2c messages from 2 -> 1 was missed. This
fixes it.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hans J. Koch [Tue, 8 Aug 2006 12:10:12 +0000 (09:10 -0300)]
V4L/DVB (4406): Convert radio-cadet to V4L2 API
This is a card with RDS capabilities.
RDS specifications didn't change from V4L1 to V4L2, so that part should be OK.
This patch changed the following stuff:
* The device can be opened multiple times. That's necessary because there are
at least a radio application and an RDS application (rdsd) that want to
open() the device.
* Added a poll() function. Every character device should have that, and rdsd
expects it as it uses select() on that file descriptor.
* Converted the ioctls to V4L2. MUTE is not implemented correctly as the
card doesn't seem to have a special bit for that. Probably there are a few
more ioctls that should at least return 0 or an error.
As I do not own such a card, I couldn't test anything. If there is anybody out
there who owns such an ancient card, please test and report.
I just checked that the code compiles.
Signed-off-by: Hans J. Koch <koch@hjk-az.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Trent Piepho [Tue, 8 Aug 2006 12:10:11 +0000 (09:10 -0300)]
V4L/DVB (4400): Tda826x: Remove 0-byte I2C write; put tuner_ops info in static struct
Remove the 0-byte write that precedes 2-byte read.
Move initialize the info field in the static tuner_ops definition, so
that it doesn't need to be done manually.
V4L/DVB (4398): Add support for Acorp TV134DS + FlyDVB-S cards.
Add support for Acorp TV134DS and FlyDVB-S cards (both based on
tda10086+tda826x)
Signed-off-by: Igor M. Liplianin <liplianin@me.by> Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Andrew Morton [Tue, 8 Aug 2006 12:10:09 +0000 (09:10 -0300)]
V4L/DVB (4394): Git-dvb: radio-sf16fmi build fix
drivers/media/radio/radio-sf16fmi.c: In function 'fmi_do_ioctl':
drivers/media/radio/radio-sf16fmi.c:147: warning: implicit declaration of function 'KERNEL_VERSION'
Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Move the call to dst_attach into the dst_attach function to eliminate
problems caused with dvb_attach.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net> Acked-by: Manu Abraham <manu@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
projects / mirror_ubuntu-zesty-kernel.git / log