Saeed Mahameed [Thu, 20 Nov 2014 12:19:44 +0000 (14:19 +0200)]
net/mlx4_en: mlx4_en_set_settings() always fails when autoneg is set
Fix ethtool set settings to not check AUTONEG_ENABLE
mlx4_en_set_settings should not check if cmd->autoneg == AUTONEG_ENABLE,
cmd->autoneg can be enabled by default and this check will fail other settings requests.
mlx4_en driver doesn't support changing autoneg value, but shouldn't fail the request
in case cmd->autoneg was set.
Fixes: d48b3ab ("net/mlx4_en: Use PTYS register to set ethtool settings (Speed)") Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Amir Vadai <amirv@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Added a pci_dma_mapping_error() call to check for mapping errors before
further using the dma handle. In case of error, control goes to a new label
where the incoming skb is freed. Unchecked dma handles were found using
Coccinelle:
@rule1@
expression e1;
identifier x;
@@
*x = pci_map_single(...);
... when != pci_dma_mapping_error(e1,x)
Signed-off-by: Tina Johnson <tinajohnson.1234@gmail.com> Acked-by: Julia Lawall <julia.lawall@lip6.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 21 Nov 2014 20:01:35 +0000 (15:01 -0500)]
Merge branch 'tipc-next'
Richard Alpe says:
====================
tipc: new netlink API
v3
The old API is not removed.
The new API is separated from the old because of a bug in the old
tipc-config utility using it. When adding commands to the existing
genl_ops struct the get-family response message grows to a point where
it overflows the small receive buffer in tipc-config, subsequently
breaking the tool. Hence the two genl_family and genl_ops structs.
The new headers are placed in a new file called tipc_netlink.h rather
than added to tipc_config.h as they where in previous versions of this
patchset.
/v3
v2
Redesigned "socket list command" to address David Millers comments in
net-next v1 of this patchset.
Simply put the problem is that we can have an arbitrary amount of
sockets with an arbitrary amount of associated publications. In the
previous patchset this was solved by nesting as many publications as
possible into a socket. If all didn't fit it sent the same socket again
with the remaining publications. As David Miller pointed out this makes
each message malformed as the receiver cannot by the data itself know if
it has received a complete set or not. This was flagged outside of the
data and the client did the reassembly.
o socket 1
o publ 1
o publ 2
o socket 1
o publ 3
o publ 4
In this patchset this is divided into socket listing and publication
listing to avoid having nested data of arbitrary size.
TIPC_NL_SOCK_GET now dumps all sockets with any nested connection
information. However, it no longer include publication information,
only a HAS_PUBL flag to indicate whether the socket has publications or
not. To compliment this there is a new command TIPC_NL_PUBL_GET which
takes a socket as argument and dumps all associated publications.
This means that on "top-level" the data is always complete. In the case
of "tipc socket list" (new tipc-config -p) it first queries all sockets
with TIPC_NL_SOCK_GET and if the socket is published it fetches the
publications using TIPC_NL_PUBL_GET. This is slow for large amount of
sockets with a low publication count (worst case). However, the
integrity is preserved and there is no malformed messages.
/v2
This is a new netlink API for TIPC. It's intended to replace the
existing ASCII API. It utilizes many of the standard netlink
functionalities in the kernel, such as attribute nesting and
input polices.
There are a couple of reasons for this rewrite. The main and most
easily justifiable is that the existing API doesn't scale. Meaning
that a TIPC cluster with a larger amount of nodes, publications or
ports will rapidly exceed what the exiting API can handle. Resulting
in truncated or corrupt responses. In addition to this, the existing
ASCII API rarely uses "standard" kernel functions and has several
tipc specific functions for sanity checking and string formating.
The new API utilizes standard function for pushing data to socket
buffers and netlink attribute nesting to logically group data.
The new API can handle an arbitrary amount of data for things that
are likely to scale up as the TIPC usage and/or cluster size
increases.
A new user-space tool has been developed to work with this new API.
It is called "tipc" and is part of the "tipc-utils" package that
comes with many Linux distributions. The new "tipc" tool utilizes
standard functions from libnl to format, send, receive and process
messages. The tool has borrowed design philosophies from git and the
ip tool. Making the syntax resemble that of ip whiles its strong
modularity resembles that of git.
The existing tool for managing TIPC, "tipc-config" remains in the
package, but when built for kernels that has this new API it is
replaced by a script-based wrapper that maps the old syntax to the
new tool. This way, backwards compatibility is mostly preserved.
MORE ABOUT THE CODE
The main challenge here is to handle the case where the data is of
arbitrary size. This was largely neglected in the old API design.
For example when there is a lot of sockets that has a large amount of
associated publications. In this specific case we can't assume that
all ports nor for that matter all the publications can fit inside a
single netlink message. Sending everything in one batch isn't an
option as we need to yield for the socket layer to cope.
This is solved by using the standard netlink callback for dumping
data and releasing the locks when the netlink message is full. The
dumping mechanism gets us back and we keep a reference (logical) to
where we where when the message became full. This means that we are
not "atomic", what is retrieved by user-space isn't a snapshot at a
certain time but rather a continuously updated data set. In the case
where we can't find our way back i.e. our logical reference are gone
we set a standard flag (NLM_F_DUMP_INTR) to tell user-space that the
dump was interrupted.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Richard Alpe [Thu, 20 Nov 2014 09:29:20 +0000 (10:29 +0100)]
tipc: add name table dump to new netlink api
Add TIPC_NL_NAME_TABLE_GET command to the new tipc netlink API.
This command supports dumping the name table of all nodes.
Netlink logical layout of name table response message:
-> name table
-> publication
-> type
-> lower
-> upper
-> scope
-> node
-> ref
-> key
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com> Reviewed-by: Erik Hugne <erik.hugne@ericsson.com> Reviewed-by: Jon Maloy <jon.maloy@ericsson.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Richard Alpe [Thu, 20 Nov 2014 09:29:19 +0000 (10:29 +0100)]
tipc: add net set to new netlink api
Add TIPC_NL_NET_SET command to the new tipc netlink API.
This command can set the network id and network (tipc) address.
Netlink logical layout of network set message:
-> net
[ -> id ]
[ -> address ]
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com> Reviewed-by: Erik Hugne <erik.hugne@ericsson.com> Reviewed-by: Jon Maloy <jon.maloy@ericsson.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Richard Alpe [Thu, 20 Nov 2014 09:29:18 +0000 (10:29 +0100)]
tipc: add net dump to new netlink api
Add TIPC_NL_NET_GET command to the new tipc netlink API.
This command dumps the network id of the node.
Netlink logical layout of returned network data:
-> net
-> id
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com> Reviewed-by: Erik Hugne <erik.hugne@ericsson.com> Reviewed-by: Jon Maloy <jon.maloy@ericsson.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Richard Alpe [Thu, 20 Nov 2014 09:29:17 +0000 (10:29 +0100)]
tipc: add node get/dump to new netlink api
Add TIPC_NL_NODE_GET to the new tipc netlink API.
This command can dump the address and node status of all nodes in the
tipc cluster.
Netlink logical layout of returned node/address data:
-> node
-> address
-> up flag
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com> Reviewed-by: Erik Hugne <erik.hugne@ericsson.com> Reviewed-by: Jon Maloy <jon.maloy@ericsson.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Richard Alpe [Thu, 20 Nov 2014 09:29:16 +0000 (10:29 +0100)]
tipc: add media set to new netlink api
Add TIPC_NL_MEDIA_SET command to the new tipc netlink API.
This command can set one or more link properties for a particular
media.
Netlink logical layout of bearer set message:
-> media
-> name
-> link properties
[ -> tolerance ]
[ -> priority ]
[ -> window ]
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com> Reviewed-by: Erik Hugne <erik.hugne@ericsson.com> Reviewed-by: Jon Maloy <jon.maloy@ericsson.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Richard Alpe [Thu, 20 Nov 2014 09:29:15 +0000 (10:29 +0100)]
tipc: add media get/dump to new netlink api
Add TIPC_NL_MEDIA_GET command to the new tipc netlink API.
This command supports dumping all information about all defined
media as well as getting all information about a specific media.
The information about a media includes name and link properties.
Netlink logical layout of media get response message:
-> media
-> name
-> link properties
-> tolerance
-> priority
-> window
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com> Reviewed-by: Erik Hugne <erik.hugne@ericsson.com> Reviewed-by: Jon Maloy <jon.maloy@ericsson.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Richard Alpe [Thu, 20 Nov 2014 09:29:14 +0000 (10:29 +0100)]
tipc: add link stat reset to new netlink api
Add TIPC_NL_LINK_RESET_STATS command to the new netlink API.
This command resets the link statistics for a particular link.
Netlink logical layout of link reset message:
-> link
-> name
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com> Reviewed-by: Erik Hugne <erik.hugne@ericsson.com> Reviewed-by: Jon Maloy <jon.maloy@ericsson.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Richard Alpe [Thu, 20 Nov 2014 09:29:13 +0000 (10:29 +0100)]
tipc: add link set to new netlink api
Add TIPC_NL_LINK_SET to the new tipc netlink API.
This command can set one or more link properties for a particular
link.
Netlink logical layout of link set message:
-> link
-> name
-> properties
[ -> tolerance ]
[ -> priority ]
[ -> window ]
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com> Reviewed-by: Erik Hugne <erik.hugne@ericsson.com> Reviewed-by: Jon Maloy <jon.maloy@ericsson.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Richard Alpe [Thu, 20 Nov 2014 09:29:12 +0000 (10:29 +0100)]
tipc: add link get/dump to new netlink api
Add TIPC_NL_LINK_GET command to the new tipc netlink API.
This command supports dumping all information about all links
(including the broadcast link) or getting all information about a
specific link (not the broadcast link).
The information about a link includes name, transmission info,
properties and link statistics.
As the tipc broadcast link is special we unfortunately have to treat
it specially. It is a deliberate decision not to abstract the
broadcast link on this (API) level.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com> Reviewed-by: Erik Hugne <erik.hugne@ericsson.com> Reviewed-by: Jon Maloy <jon.maloy@ericsson.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Richard Alpe [Thu, 20 Nov 2014 09:29:11 +0000 (10:29 +0100)]
tipc: add publication dump to new netlink api
Add TIPC_NL_PUBL_GET command to the new tipc netlink API.
This command supports dumping of all publications for a specific
socket.
Netlink logical layout of request message:
-> socket
-> reference
Netlink logical layout of response message:
-> publication
-> type
-> lower
-> upper
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com> Reviewed-by: Erik Hugne <erik.hugne@ericsson.com> Reviewed-by: Jon Maloy <jon.maloy@ericsson.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Richard Alpe [Thu, 20 Nov 2014 09:29:10 +0000 (10:29 +0100)]
tipc: add sock dump to new netlink api
Add TIPC_NL_SOCK_GET command to the new tipc netlink API.
This command supports dumping of all available sockets with their
associated connection or publication(s). It could be extended to reply
with a single socket if the NLM_F_DUMP isn't set.
The information about a socket includes reference, address, connection
information / publication information.
Netlink logical layout of response message:
-> socket
-> reference
-> address
[
-> connection
-> node
-> socket
[
-> connected flag
-> type
-> instance
]
]
[
-> publication flag
]
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com> Reviewed-by: Erik Hugne <erik.hugne@ericsson.com> Reviewed-by: Jon Maloy <jon.maloy@ericsson.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Richard Alpe [Thu, 20 Nov 2014 09:29:09 +0000 (10:29 +0100)]
tipc: add bearer set to new netlink api
Add TIPC_NL_BEARER_SET command to the new tipc netlink API.
This command can set one or more link properties for a particular
bearer.
Netlink logical layout of bearer set message:
-> bearer
-> name
-> link properties
[ -> tolerance ]
[ -> priority ]
[ -> window ]
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com> Reviewed-by: Erik Hugne <erik.hugne@ericsson.com> Reviewed-by: Jon Maloy <jon.maloy@ericsson.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Richard Alpe [Thu, 20 Nov 2014 09:29:08 +0000 (10:29 +0100)]
tipc: add bearer get/dump to new netlink api
Add TIPC_NL_BEARER_GET command to the new tipc netlink API.
This command supports dumping all data about all bearers or getting
all information about a specific bearer.
The information about a bearer includes name, link priorities and
domain.
Netlink logical layout of bearer get message:
-> bearer
-> name
Netlink logical layout of returned bearer information:
-> bearer
-> name
-> link properties
-> priority
-> tolerance
-> window
-> domain
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com> Reviewed-by: Erik Hugne <erik.hugne@ericsson.com> Reviewed-by: Jon Maloy <jon.maloy@ericsson.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Richard Alpe [Thu, 20 Nov 2014 09:29:07 +0000 (10:29 +0100)]
tipc: add bearer disable/enable to new netlink api
A new netlink API for tipc that can disable or enable a tipc bearer.
The new API is separated from the old API because of a bug in the
user space client (tipc-config). The problem is that older versions
of tipc-config has a very low receive limit and adding commands to
the legacy genl_opts struct causes the ctrl_getfamily() response
message to grow, subsequently breaking the tool.
The new API utilizes netlink policies for input validation. Where the
top-level netlink attributes are tipc-logical entities, like bearer.
The top level entities then contain nested attributes. In this case
a name, nested link properties and a domain.
Netlink commands implemented in this patch:
TIPC_NL_BEARER_ENABLE
TIPC_NL_BEARER_DISABLE
Netlink logical layout of bearer disable message:
-> bearer
-> name
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com> Reviewed-by: Erik Hugne <erik.hugne@ericsson.com> Reviewed-by: Jon Maloy <jon.maloy@ericsson.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Thu, 20 Nov 2014 08:31:05 +0000 (16:31 +0800)]
macvtap: advance iov iterator when needed in macvtap_put_user()
When mergeable buffer is used, vnet_hdr_sz is greater than sizeof struct
virtio_net_hdr. So we need advance the iov iterators in this case.
Fixes 6c36d2e26cda1ad3e2c4b90dd843825fc62fe5b4 ("macvtap: Use iovec iterators") Cc: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
hayeswang [Thu, 20 Nov 2014 02:29:05 +0000 (10:29 +0800)]
r8152: adjust r8152_submit_rx
The behavior of handling the returned status from r8152_submit_rx()
is almost same, so let r8152_submit_rx() deal with the error
directly. This could avoid the duplicate code.
Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Thu, 20 Nov 2014 00:54:48 +0000 (01:54 +0100)]
net: sctp: keep owned chunk in destructor_arg instead of skb->cb
It's just silly to hold the skb destructor argument around inside
skb->cb[] as we currently do in SCTP.
Nowadays, we're sort of cheating on data accounting in the sense
that due to commit 4c3a5bdae293 ("sctp: Don't charge for data in
sndbuf again when transmitting packet"), we orphan the skb already
in the SCTP output path, i.e. giving back charged data memory, and
use a different destructor only to make sure the sk doesn't vanish
on skb destruction time. Thus, cb[] is still valid here as we
operate within the SCTP layer. (It's generally actually a big
candidate for future rework, imho.)
However, storing the destructor in the cb[] can easily cause issues
should an non sctp_packet_set_owner_w()'ed skb ever escape the SCTP
layer, since cb[] may get overwritten by lower layers and thus can
corrupt the chunk pointer. There are no such issues at present,
but lets keep the chunk in destructor_arg, as this is the actual
purpose for it.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Acked-by: Vlad Yasevich <vyasevich@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Wed, 19 Nov 2014 18:29:56 +0000 (10:29 -0800)]
net: bcmgenet: log RX buffer allocation and RX/TX dma failures
To help troubleshoot heavy memory pressure conditions, add a bunch of
statistics counter to log RX buffer allocation and RX/TX DMA mapping
failures. These are reported like any other counters through the ethtool
stats interface.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Wed, 19 Nov 2014 18:29:55 +0000 (10:29 -0800)]
net: systemport: log RX buffer allocation and RX/TX DMA failures
To help troubleshoot heavy memory pressure conditions, add a bunch of
statistics counter to log RX buffer allocation and RX/TX DMA mapping
failures. These are reported like any other counters through the ethtool
stats interface.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Wed, 19 Nov 2014 18:10:16 +0000 (13:10 -0500)]
packet: make packet_snd fail on len smaller than l2 header
When sending packets out with PF_PACKET, SOCK_RAW, ensure that the
packet is at least as long as the device's expected link layer header.
This check already exists in tpacket_snd, but not in packet_snd.
Also rate limit the warning in tpacket_snd.
Signed-off-by: Willem de Bruijn <willemb@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Acked-by: Daniel Borkmann <dborkman@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Wed, 19 Nov 2014 13:05:01 +0000 (14:05 +0100)]
net: move make_writable helper into common code
note that skb_make_writable already exists in net/netfilter/core.c
but does something slightly different.
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Jiri Pirko <jiri@resnulli.us> Acked-by: Pravin B Shelar <pshelar@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Wed, 19 Nov 2014 13:05:00 +0000 (14:05 +0100)]
vlan: introduce __vlan_insert_tag helper which does not free skb
There's a need for helper which inserts vlan tag but does not free the
skb in case of an error.
Suggested-by: Pravin Shelar <pshelar@nicira.com> Signed-off-by: Jiri Pirko <jiri@resnulli.us> Acked-by: Pravin B Shelar <pshelar@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Wed, 19 Nov 2014 13:04:55 +0000 (14:04 +0100)]
openvswitch: actions: use skb_postpull_rcsum when possible
Replace duplicated code by calling skb_postpull_rcsum
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Jiri Pirko <jiri@resnulli.us> Acked-by: Pravin B Shelar <pshelar@nicira.com> Acked-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This series adds device and device-type abstractions to the micrel
driver, and enables support for RMII-reference clock selection for
KSZ8081 and KSZ8091 devices.
While adding support for more features for the Micrel PHYs mentioned
above, it became apparent that the configuration space is much too large
and that adding type-specific callbacks will simply not scale. Instead I
added a driver_data field to struct phy_device, which can be used to
store static device type data that can be parsed and acted on in
generic driver callbacks. This allows a lot of duplicated code to be
removed, and should make it much easier to add new features or deal with
device-type quirks in the future.
The series has been tested on a dual KSZ8081 setup. Further testing on
other Micrel PHYs would be much appreciated.
The recent commit a95a18afe4c8 ("phy/micrel: KSZ8031RNL RMII clock
reconfiguration bug") currently prevents KSZ8031 PHYs from using the
generic config-init. Bruno, who is the author of that patch, has agreed
to test this series and some follow-up diagnostic patches to determine
how best to incorporate these devices as well. I intend to send a
follow-up patch that removes the custom 8031 config-init and documents
this quirk, but the current series can be applied meanwhile.
These patches are against net-next which contains some already merged
prerequisite patches to the driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hovold [Wed, 19 Nov 2014 11:59:21 +0000 (12:59 +0100)]
dt/bindings: add clock-select function property to micrel phy binding
Add "micrel,rmii-reference-clock-select-25-mhz" to Micrel ethernet PHY
binding documentation.
This property is needed to properly describe some revisions of Micrel
PHYs which has the function of this configuration bit inverted so that
setting it enables 25 MHz rather than 50 MHz clock mode.
Note that a clock reference ("rmii-ref") is still needed to actually
select either mode.
Cc: devicetree@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hovold [Wed, 19 Nov 2014 11:59:19 +0000 (12:59 +0100)]
net: phy: micrel: add support for clock-mode select to KSZ8081/KSZ8091
Micrel KSZ8081 and KSZ8091 PHYs have the RMII Reference Clock Select
bit, which is used to select 25 or 50 MHz clock mode.
Note that on some revisions of the PHY (e.g. KSZ8081RND) the function of
this bit is inverted so that setting it enables 25 rather than 50 MHz
mode. Add a new device-tree property
"micrel,rmii-reference-clock-select-25-mhz" to describe this.
Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hovold [Wed, 19 Nov 2014 11:59:18 +0000 (12:59 +0100)]
net: phy: micrel: add generic clock-mode-select support
Add generic RMII-Reference-Clock-Select support.
Several Micrel PHY have an RMII-Reference-Clock-Select bit to select
25 MHz or 50 MHz clock mode. Recently, support for configuring this
through device tree for KSZ8021 and KSZ8031 was added.
Generalise this support so that it can be configured for other PHY types
as well.
Note that some PHY revisions (of the same type) has this bit inverted.
This should be either configurable through a new device-tree property,
or preferably, determined based on PHY ID if possible.
Also note that this removes support for setting 25 MHz mode from board
files which was also added by the above mentioned commit 45f56cb82e45
("net/phy: micrel: Add clock support for KSZ8021/KSZ8031").
Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Morris <ipm@chirality.org.uk> Cc: Mirko Lindner <mlindner@marvell.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Cc: Eric Dumazet <edumazet@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Check and update posted_index only when skb->xmit_more is 0 or tx queue is full.
v2:
use txq_map instead of skb_get_queue_mapping(skb)
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 20 Nov 2014 00:10:17 +0000 (19:10 -0500)]
Merge branch 'bonding_4ad'
Xie Jianhua says:
====================
bonding: Introduce 4 AD link speed
The speed field of AD Port Key was based on bitmask, it supported 5
kinds of link speed at most, as there were only 5 bits in the speed
field of the AD Port Key. This patches series change the speed type
(AD_LINK_SPEED_BITMASK) from bitmask to enum type in order to enhance
speed type from 5 to 32, and then introduce 4 AD link speed to fix
agg_bandwidth.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jianhua Xie [Wed, 19 Nov 2014 08:48:59 +0000 (16:48 +0800)]
bonding: Introduce 4 AD link speed to fix agg_bandwidth
This patch adds [2.5|20|40|56] Gbps enum definition, and fixes
aggregated bandwidth calculation based on above slave links.
CC: Jay Vosburgh <j.vosburgh@gmail.com> CC: Veaceslav Falico <vfalico@gmail.com> CC: Andy Gospodarek <andy@greyhouse.net> CC: David S. Miller <davem@davemloft.net> Signed-off-by: Jianhua Xie <jianhua.xie@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jianhua Xie [Wed, 19 Nov 2014 08:48:58 +0000 (16:48 +0800)]
bonding: change AD_LINK_SPEED_BITMASK to enum to suport more speed
Port Key was determined as 16 bits according to the link speed,
duplex and user key (which is yet not supported). In the old
speed field, 5 bits are for speed [1|10|100|1000|10000]Mbps as
below:
--------------------------------------------------------------
Port key :| User key | Speed | Duplex|
--------------------------------------------------------------
16 6 1 0
This patch keeps the old layout, but changes AD_LINK_SPEED_BITMASK
from bit type to an enum type. In this way, the speed field can
expand speed type from 5 to 32.
CC: Jay Vosburgh <j.vosburgh@gmail.com> CC: Veaceslav Falico <vfalico@gmail.com> CC: Andy Gospodarek <andy@greyhouse.net> CC: David S. Miller <davem@davemloft.net> Signed-off-by: Jianhua Xie <jianhua.xie@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Al Viro [Mon, 10 Nov 2014 03:33:45 +0000 (22:33 -0500)]
{compat_,}verify_iovec(): switch to generic copying of iovecs
use {compat_,}rw_copy_check_uvector(). As the result, we are
guaranteed that all iovecs seen in ->msg_iov by ->sendmsg()
and ->recvmsg() will pass access_ok().
Al Viro [Sun, 6 Apr 2014 18:03:05 +0000 (14:03 -0400)]
separate kernel- and userland-side msghdr
Kernel-side struct msghdr is (currently) using the same layout as
userland one, but it's not a one-to-one copy - even without considering
32bit compat issues, we have msg_iov, msg_name and msg_control copied
to kernel[1]. It's fairly localized, so we get away with a few functions
where that knowledge is needed (and we could shrink that set even
more). Pretty much everything deals with the kernel-side variant and
the few places that want userland one just use a bunch of force-casts
to paper over the differences.
The thing is, kernel-side definition of struct msghdr is *not* exposed
in include/uapi - libc doesn't see it, etc. So we can add struct user_msghdr,
with proper annotations and let the few places that ever deal with those
beasts use it for userland pointers. Saner typechecking aside, that will
allow to change the layout of kernel-side msghdr - e.g. replace
msg_iov/msg_iovlen there with struct iov_iter, getting rid of the need
to modify the iovec as we copy data to/from it, etc.
We could introduce kernel_msghdr instead, but that would create much more
noise - the absolute majority of the instances would need to have the
type switched to kernel_msghdr and definition of struct msghdr in
include/linux/socket.h is not going to be seen by userland anyway.
This commit just introduces user_msghdr and switches the few places that
are dealing with userland-side msghdr to it.
[1] actually, it's even trickier than that - we copy msg_control for
sendmsg, but keep the userland address on recvmsg.
bpf: fix arraymap NULL deref and missing overflow and zero size checks
- fix NULL pointer dereference:
kernel/bpf/arraymap.c:41 array_map_alloc() error: potential null dereference 'array'. (kzalloc returns null)
kernel/bpf/arraymap.c:41 array_map_alloc() error: we previously assumed 'array' could be null (see line 40)
- integer overflow check was missing in arraymap
(hashmap checks for overflow via kmalloc_array())
- arraymap can round_up(value_size, 8) to zero. check was missing.
- hashmap was missing zero size check as well, since roundup_pow_of_two() can
truncate into zero
- found a typo in the arraymap comment and unnecessary empty line
Fix all of these issues and make both overflow checks explicit U32 in size.
Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Recently many changes have been done inside the driver
so this patch updates the driver's doc for example reviewing
information for the rx and tx processes that are managed
by napi method, adding new information for missing glue-logic files
etc.
Also this reviews and fixes what is reported when run kernel-doc script.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently many changes have been done inside the driver
so this patch updates the driver's doc for example reviewing
information for the rx and tx processes that are managed
by napi method, adding new information for missing glue-logic files
etc.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 18 Nov 2014 07:06:20 +0000 (23:06 -0800)]
tcp: make connect() mem charging friendly
While working on sk_forward_alloc problems reported by Denys
Fedoryshchenko, we found that tcp connect() (and fastopen) do not call
sk_wmem_schedule() for SYN packet (and/or SYN/DATA packet), so
sk_forward_alloc is negative while connect is in progress.
We can fix this by calling regular sk_stream_alloc_skb() both for the
SYN packet (in tcp_connect()) and the syn_data packet in
tcp_send_syn_data()
Then, tcp_send_syn_data() can avoid copying syn_data as we simply
can manipulate syn_data->cb[] to remove SYN flag (and increment seq)
Instead of open coding memcpy_fromiovecend(), simply use this helper.
This leaves in socket write queue clean fast clone skbs.
This was tested against our fastopen packetdrill tests.
Reported-by: Denys Fedoryshchenko <nuclearcat@nuclearcat.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Tue, 18 Nov 2014 05:20:41 +0000 (13:20 +0800)]
tun: return NET_XMIT_DROP for dropped packets
After commit 5d097109257c03a71845729f8db6b5770c4bbedc
("tun: only queue packets on device"), NETDEV_TX_OK was returned for
dropped packets. This will confuse pktgen since dropped packets were
counted as sent ones.
Fixing this by returning NET_XMIT_DROP to let pktgen count it as error
packet.
Cc: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rick Jones [Mon, 17 Nov 2014 22:04:29 +0000 (14:04 -0800)]
icmp: Remove some spurious dropped packet profile hits from the ICMP path
If icmp_rcv() has successfully processed the incoming ICMP datagram, we
should use consume_skb() rather than kfree_skb() because a hit on the likes
of perf -e skb:kfree_skb is not called-for.
Signed-off-by: Rick Jones <rick.jones2@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 18 Nov 2014 20:24:53 +0000 (15:24 -0500)]
Merge tag 'linux-can-next-for-3.19-20141117' of git://gitorious.org/linux-can/linux-can-next
Marc Kleine-Budde says:
====================
this is a pull request of 9 patches for net-next/master.
All 9 patches are by Roger Quadros and update the c_can platform
driver. First by improving the initialization sequence of the message
RAM, making use of syscon/regmap. In the later patches support for
various TI SoCs is added.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch series is a followup to:
<1415350967-2238-1-git-send-email-LW@KARO-electronics.de>
[PATCHv4 1/1] net: fec: fix regression on i.MX28 introduced by rx_copybreak support
to apply the cleanup patches that were originally sent along with the
bugfix patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Lothar Waßmann [Mon, 17 Nov 2014 09:51:22 +0000 (10:51 +0100)]
net: fec: use swab32s() instead of cpu_to_be32()
when swap_buffer() is being called, we know for sure, that we need to
byte swap the data. Furthermore, this function is called for swapping
data in both directions. Thus cpu_to_be32() is semantically not
correct for all use cases. Use swab32s() to reflect this.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 18 Nov 2014 18:44:06 +0000 (13:44 -0500)]
Merge branch 'ebpf_maps'
Alexei Starovoitov says:
====================
implementation of eBPF maps
v1->v2:
renamed flags for MAP_UPDATE_ELEM command to be more concise,
clarified commit logs and improved comments in patches 1,3,7
per discussions with Daniel
Old v1 cover:
this set of patches adds implementation of HASH and ARRAY types of eBPF maps
which were described in manpage in commit b4fc1a460f30("Merge branch 'bpf-next'")
The difference vs previous version of these patches from August:
- added 'flags' attribute to BPF_MAP_UPDATE_ELEM
- in HASH type implementation removed per-map kmem_cache.
I was doing kmem_cache_create() for every map to enable selective slub
debugging to check for overflows and leaks. Now it's not needed, so just
use normal kmalloc() for map elements.
- added ARRAY type which was mentioned in manpage, but wasn't public yet
- added map testsuite and removed temporary bits from test_stubs
Note, eBPF programs cannot be attached to events yet.
It will come in the next set.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
. check error conditions and sanity of hash and array map APIs
. check large maps (that kernel gracefully switches to vmalloc from kmalloc)
. check multi-process parallel access and stress test
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net>
fix errno of BPF_MAP_LOOKUP_ELEM command as bpf manpage
described it in commit b4fc1a460f30("Merge branch 'bpf-next'"):
-----
BPF_MAP_LOOKUP_ELEM
int bpf_lookup_elem(int fd, void *key, void *value)
{
union bpf_attr attr = {
.map_fd = fd,
.key = ptr_to_u64(key),
.value = ptr_to_u64(value),
};
return bpf(BPF_MAP_LOOKUP_ELEM, &attr, sizeof(attr));
}
bpf() syscall looks up an element with given key in a map fd.
If element is found it returns zero and stores element's value
into value. If element is not found it returns -1 and sets
errno to ENOENT.
and further down in manpage:
ENOENT For BPF_MAP_LOOKUP_ELEM or BPF_MAP_DELETE_ELEM, indicates that
element with given key was not found.
-----
In general all BPF commands return ENOENT when map element is not found
(including BPF_MAP_GET_NEXT_KEY and BPF_MAP_UPDATE_ELEM with
flags == BPF_MAP_UPDATE_ONLY)
Subsequent patch adds a testsuite to check return values for all of
these combinations.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net>
add new map type BPF_MAP_TYPE_ARRAY and its implementation
- optimized for fastest possible lookup()
. in the future verifier/JIT may recognize lookup() with constant key
and optimize it into constant pointer. Can optimize non-constant
key into direct pointer arithmetic as well, since pointers and
value_size are constant for the life of the eBPF program.
In other words array_map_lookup_elem() may be 'inlined' by verifier/JIT
while preserving concurrent access to this map from user space
- two main use cases for array type:
. 'global' eBPF variables: array of 1 element with key=0 and value is a
collection of 'global' variables which programs can use to keep the state
between events
. aggregation of tracing events into fixed set of buckets
- all array elements pre-allocated and zero initialized at init time
- key as an index in array and can only be 4 byte
- map_delete_elem() returns EINVAL, since elements cannot be deleted
- map_update_elem() replaces elements in an non-atomic way
(for atomic updates hashtable type should be used instead)
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net>
add new map type BPF_MAP_TYPE_HASH and its implementation
- maps are created/destroyed by userspace. Both userspace and eBPF programs
can lookup/update/delete elements from the map
- eBPF programs can be called in_irq(), so use spin_lock_irqsave() mechanism
for concurrent updates
- key/value are opaque range of bytes (aligned to 8 bytes)
- user space provides 3 configuration attributes via BPF syscall:
key_size, value_size, max_entries
- map takes care of allocating/freeing key/value pairs
- map_update_elem() must fail to insert new element when max_entries
limit is reached to make sure that eBPF programs cannot exhaust memory
- map_update_elem() replaces elements in an atomic way
- optimized for speed of lookup() which can be called multiple times from
eBPF program which itself is triggered by high volume of events
. in the future JIT compiler may recognize lookup() call and optimize it
further, since key_size is constant for life of eBPF program
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bpf: add 'flags' attribute to BPF_MAP_UPDATE_ELEM command
the current meaning of BPF_MAP_UPDATE_ELEM syscall command is:
either update existing map element or create a new one.
Initially the plan was to add a new command to handle the case of
'create new element if it didn't exist', but 'flags' style looks
cleaner and overall diff is much smaller (more code reused), so add 'flags'
attribute to BPF_MAP_UPDATE_ELEM command with the following meaning:
#define BPF_ANY 0 /* create new element or update existing */
#define BPF_NOEXIST 1 /* create new element if it didn't exist */
#define BPF_EXIST 2 /* update existing element */
bpf_update_elem(fd, key, value, BPF_NOEXIST) call can fail with EEXIST
if element already exists.
bpf_update_elem(fd, key, value, BPF_EXIST) can fail with ENOENT
if element doesn't exist.
Userspace will call it as:
int bpf_update_elem(int fd, void *key, void *value, __u64 flags)
{
union bpf_attr attr = {
.map_fd = fd,
.key = ptr_to_u64(key),
.value = ptr_to_u64(value),
.flags = flags;
};
David S. Miller [Tue, 18 Nov 2014 18:37:29 +0000 (13:37 -0500)]
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-11-18
This series contains updates to i40e only.
Shannon provides a patch to clean up the driver to only warn once that
PTP is not supported when linked at 100Mbps.
Mitch provides a fix for i40e where the VF interrupt processing takes
a long time and it is possible that we could lose a VFLR event if it
happens while processing a VFLR on another VF. To correct this situation,
we enable the VFLR interrupt cause before we begin processing any pending
resets.
Neerav provides several patches to update DCB support in i40e. When
there are DCB configuration changes based on DCBx, the firmware suspends
the port's Tx and generates an event to the PF. The PF is then
responsible to reconfigure the PF VSIs and switching topology as per the
updated DCB configuration and then resume the port's Tx by calling the
"Resume Port Tx" AQ command, so add this call to the flow that handles
DCB re-configuration in the PF. Allow the driver to query and use DCB
configuration from firmware when firmware DCBx agent is in CEE mode.
Add a check whether LLDP Agent's default AdminStatus is enabled or
disabled on a given port, and sets DCBx status to disabled if the
status is disabled. Fix an issue when the port TC configuration
changes as a result of DCBx and the driver modifies the enabled TCs for
the VEBs it manages but does not update the enabled_tc value that
was cached on a per VEB basis. Add a new PF state so that if a port's
Tx is in suspended state the Tx queue disable flow would just put the
request for the queue to be disabled and return without waiting for the
queue to be actually disabled. Allows the driver to enable/disable
the XPS based on the number of TCs being enabled for the given VSI.
v2: Dropped patch "i40e: Handle a single mss packet with more than 8 frags"
while we rework the patch after we test a bit more based on feedback from
Eric Dumazet.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Denis Kirjanov [Mon, 17 Nov 2014 20:07:41 +0000 (23:07 +0300)]
PPC: bpf_jit_comp: Unify BPF_MOD | BPF_X and BPF_DIV | BPF_X
Reduce duplicated code by unifying
BPF_ALU | BPF_MOD | BPF_X and BPF_ALU | BPF_DIV | BPF_X
CC: Alexei Starovoitov<alexei.starovoitov@gmail.com> CC: Daniel Borkmann<dborkman@redhat.com> CC: Philippe Bergheaud<felix@linux.vnet.ibm.com> Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org> Acked-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Neerav Parikh [Wed, 12 Nov 2014 00:19:02 +0000 (00:19 +0000)]
i40e: Set XPS bit mask to zero in DCB mode
Due to DCBX configuration change if the VSI needs to use more than 1 TC;
it needs to disable the XPS maps that were set when operating in 1 TC mode.
Without disabling XPS the netdev layer will select queues based on those
settings and not use the TC queue mapping to make the queue selection.
This patch allows the driver to enable/disable the XPS based on the number
of TCs being enabled for the given VSI.
Change-ID: Idc4dec47a672d2a509f6d7fe11ed1ee65b4f0e08 Signed-off-by: Neerav Parikh <neerav.parikh@intel.com> Tested-By: Jack Morgan <jack.morgan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
projects / mirror_ubuntu-kernels.git / log