Tony Lindgren [Fri, 6 Mar 2015 18:37:34 +0000 (10:37 -0800)]
ARM: OMAP2+: Fix wl12xx on dm3730-evm with mainline u-boot
I upgraded my u-boot and noticed that wl12xx stopped working.
Turns out the kernel is not setting the quirk for the MMC2
copy clock while the eariler bootloader I had was setting it.
Tony Lindgren [Fri, 6 Mar 2015 17:54:02 +0000 (09:54 -0800)]
Merge tag 'for-v4.0-rc/omap-fixes-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v4.0/fixes
ARM: OMAP2+: first set of hwmod and PRCM fixes for v4.0-rc
This series fixes the following bugs:
- a lockdep problem with the OMAP hwmod code;
- incorrect PCIe hwmod data for the DRA7xx chips;
- the clockdomain handling in the hardreset deassertion code,
preventing idle;
- the use of an IRQ status register rather than an IRQ enable register
in the OMAP4 PRM code.
Basic build, boot, and PM test results are available here:
Roger Quadros [Thu, 5 Mar 2015 13:32:43 +0000 (15:32 +0200)]
ARM: dts: dra7x-evm: avoid possible contention while muxing on CAN lines
DCAN1 RX and TX lines are internally pulled high according to [1].
While muxing between DCAN mode and SAFE mode we make sure
that the same pull direction is set to minimize opposite
pull contention during the switching window.
[1] in DRA7 data manual, Ball characteristics table 4-2, DSIS colum shows
the state driven to the peripheral input while in the deselcted mode.
DSIS - De-Selected Input State.
Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
According to AM437x TRM, Document SPRUHL7B, Revised December 2014,
Section 7.2.1 Pad Control Registers, setting bit 19 of the pad control
registers actually sets the SLEWCTRL value to slow rather than fast as
the current macro indicates. Introduce a new macro, SLEWCTRL_SLOW, that
sets the bit, and modify SLEWCTRL_FAST to 0 but keep it for
completeness.
Current users of the macro (i2c, mdio, and uart) are left unmodified as
SLEWCTRL_FAST was the macro used and actual desired state. Tested on
am437x-gp-evm with no difference in software performance seen.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
According to AM335x TRM, Document spruh73l, Revised February 2015,
Section 9.2.2 Pad Control Registers, setting bit 6 of the pad control
registers actually sets the SLEWCTRL value to slow rather than fast as
the current macro indicates. Introduce a new macro, SLEWCTRL_SLOW, that
sets the bit, and modify SLEWCTRL_FAST to 0 but keep it for
completeness.
Current users of the macro (i2c and mdio) are left unmodified as
SLEWCTRL_FAST was the macro used and actual desired state. Tested on
am335x-gp-evm with no difference in software performance seen.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Tero Kristo [Fri, 27 Feb 2015 13:59:03 +0000 (15:59 +0200)]
ARM: dts: OMAP5: fix polling intervals for thermal zones
OMAP4 has a finer counter granularity, which allows for a delay of 1000ms
in the thermal zone polling intervals. OMAP5 has a different counter
mechanism, which allows at maximum a 500ms timer. Adjust the cpu thermal
zone polling interval accordingly.
Without this patch, the polling interval information is simply ignored,
and the following thermal warnings are printed during boot (assuming
thermal is enabled);
[ 1.545343] ti-soc-thermal 4a0021e0.bandgap: Delay 1000 ms is not supported
[ 1.552691] ti-soc-thermal 4a0021e0.bandgap: Delay 1000 ms is not supported
[ 1.560029] ti-soc-thermal 4a0021e0.bandgap: Delay 1000 ms is not supported
Signed-off-by: Tero Kristo <t-kristo@ti.com> Cc: Tony Lindgren <tony@atomide.com> Acked-by: Eduardo Valentin <edubezval@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Matt Porter [Wed, 25 Feb 2015 18:52:41 +0000 (13:52 -0500)]
ARM: dts: am335x-bone-common: enable aes and sham
Beaglebone Black doesn't have AES and SHAM enabled like the
original Beaglebone White dts. This breaks applications that
leverage the crypto blocks so fix this by enabling these nodes
in the am335x-bone-common.dtsi. With this change, enabling the
nodes in am335x-bone.dts is no longer required so remove them.
Signed-off-by: Matt Porter <mporter@konsulko.com> Acked-by: Robert Nelson <robertcnelson@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Vignesh R [Tue, 10 Feb 2015 05:35:42 +0000 (11:05 +0530)]
ARM: dts: am43xx-clocks: Fix ehrpwm tbclk data on am43xx
ehrpwm tbclk is wrongly modelled as deriving from dpll_per_m2_ck.
The TRM says tbclk is derived from SYSCLKOUT. SYSCLKOUT nothing but the
functional clock of pwmss (l4ls_gclk).
Fix this by changing source of ehrpwmx_tbclk to l4ls_gclk.
Fixes: 4da1c67719f61 ("add tbclk data for ehrpwm") Signed-off-by: Vignesh R <vigneshr@ti.com> Acked-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Vignesh R [Tue, 10 Feb 2015 05:35:41 +0000 (11:05 +0530)]
ARM: dts: am33xx-clocks: Fix ehrpwm tbclk data on am33xx
ehrpwm tbclk is wrongly modelled as deriving from dpll_per_m2_ck.
The TRM says tbclk is derived from SYSCLKOUT. SYSCLKOUT nothing but the
functional clock of pwmss (l4ls_gclk).
Fix this by changing source of ehrpwmx_tbclk to l4ls_gclk.
Fixes: 9e100ebafb91: ("Fix ehrpwm tbclk data") Signed-off-by: Vignesh R <vigneshr@ti.com> Acked-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
On OMAP54xx, For DPLL_IVA, the ref clock(CLKINP) is connected to sys_clk1 and
the bypass input(CLKINPULOW) is connected to iva_dpll_hs_clk_div clock.
But the bypass input is not directly routed to bypass clkout instead
both CLKINP and CLKINPULOW are connected to bypass clkout via a mux.
This mux is controlled by the bit - CM_CLKSEL_DPLL_IVA[23]:DPLL_BYP_CLKSEL
and it's POR value is zero which selects the CLKINP as bypass clkout.
which means iva_dpll_hs_clk_div is not the bypass clock for dpll_iva_ck
Fix this by adding another mux clock as parent in bypass mode.
This design is common to most of the PLLs and the rest have only one bypass
clock. Below is a list of the DPLLs that need this fix:
DPLL_IVA,
DPLL_PER,
DPLL_USB and DPLL_CORE
Signed-off-by: Ravikumar Kattekola <rk@ti.com> Acked-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: DRA7x: Fix the bypass clock source for dpll_iva and others
Fixes: ee6c750761 (ARM: dts: dra7 clock data)
On DRA7x, For DPLL_IVA, the ref clock(CLKINP) is connected to sys_clk1 and
the bypass input(CLKINPULOW) is connected to iva_dpll_hs_clk_div clock.
But the bypass input is not directly routed to bypass clkout instead
both CLKINP and CLKINPULOW are connected to bypass clkout via a mux.
This mux is controlled by the bit - CM_CLKSEL_DPLL_IVA[23]:DPLL_BYP_CLKSEL
and it's POR value is zero which selects the CLKINP as bypass clkout.
which means iva_dpll_hs_clk_div is not the bypass clock for dpll_iva_ck
Fix this by adding another mux clock as parent in bypass mode.
This design is common to most of the PLLs and the rest have only one bypass
clock. Below is a list of the DPLLs that need this fix:
DPLL_IVA, DPLL_DDR,
DPLL_DSP, DPLL_EVE,
DPLL_GMAC, DPLL_PER,
DPLL_USB and DPLL_CORE
Signed-off-by: Ravikumar Kattekola <rk@ti.com> Acked-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Daniel Vetter [Tue, 3 Mar 2015 16:31:21 +0000 (17:31 +0100)]
drm/i915: Fix modeset state confusion in the load detect code
This is a tricky story of the new atomic state handling and the legacy
code fighting over each another. The bug at hand is an underrun of the
framebuffer reference with subsequent hilarity caused by the load
detect code. Which is peculiar since the the exact same code works
fine as the implementation of the legacy setcrtc ioctl.
Let's look at the ingredients:
- Currently our code is a crazy mix of legacy modeset interfaces to
set the parameters and half-baked atomic state tracking underneath.
While this transition is going we're using the transitional plane
helpers to update the atomic side (drm_plane_helper_disable/update
and friends), i.e. plane->state->fb. Since the state structure owns
the fb those functions take care of that themselves.
The legacy state (specifically crtc->primary->fb) is still managed
by the old code (and mostly by the drm core), with the fb reference
counting done by callers (core drm for the ioctl or the i915 load
detect code). The relevant commit is
- drm_plane_helper_disable has special code to handle multiple calls
in a row - it checks plane->crtc == NULL and bails out. This is to
match the proper atomic implementation which needs the crtc to get
at the implied locking context atomic updates always need. See
- The universal plane code split out the implicit primary plane from
the CRTC into it's own full-blown drm_plane object. As part of that
the setcrtc ioctl (which updated both the crtc mode and primary
plane) learned to set crtc->primary->crtc on modeset to make sure
the plane->crtc assignments statate up to date in
Unfortunately we've forgotten to update the load detect code. Which
wasn't a problem since the load detect modeset is temporary and
always undone before we drop the locks.
- Finally there is a organically grown history (i.e. don't ask) around
who sets the legacy plane->fb for the various driver entry points.
Originally updating that was the drivers duty, but for almost all
places we've moved that (plus updating the refcounts) into the core.
Again the exception is the load detect code.
Taking all together the following happens:
- The load detect code doesn't set crtc->primary->crtc. This is only
really an issue on crtcs never before used or when userspace
explicitly disabled the primary plane.
- The plane helper glue code short-circuits because of that and leaves
a non-NULL fb behind in plane->state->fb and plane->fb. The state
fb isn't a real problem (it's properly refcounted on its own), it's
just the canary.
- Load detect code drops the reference for that fb, but doesn't set
plane->fb = NULL. This is ok since it's still living in that old
world where drivers had to clear the pointer but the core/callers
handled the refcounting.
- On the next modeset the drm core notices plane->fb and takes care of
refcounting it properly by doing another unref. This drops the
refcount to zero, leaving state->plane now pointing at freed memory.
- intel_plane_duplicate_state still assume it owns a reference to that
very state->fb and bad things start to happen.
Fix this all by applying the same duct-tape as for the legacy setcrtc
ioctl code and set crtc->primary->crtc properly.
Cc: Matt Roper <matthew.d.roper@intel.com> Cc: Paul Bolle <pebolle@tiscali.nl> Cc: Rob Clark <robdclark@gmail.com> Cc: Paulo Zanoni <przanoni@gmail.com> Cc: Sean Paul <seanpaul@chromium.org> Cc: Matt Roper <matthew.d.roper@intel.com> Reported-and-tested-by: Linus Torvalds <torvalds@linux-foundation.org> Reported-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 2 Mar 2015 22:13:39 +0000 (14:13 -0800)]
Merge tag 'gpio-v4.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Two GPIO fixes:
- Fix a translation problem in of_get_named_gpiod_flags()
- Fix a long standing container_of() mistake in the TPS65912 driver"
* tag 'gpio-v4.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: tps65912: fix wrong container_of arguments
gpiolib: of: allow of_gpiochip_find_and_xlate to find more than one chip per node
Linus Torvalds [Mon, 2 Mar 2015 22:08:10 +0000 (14:08 -0800)]
Merge branch 'fixes-for-4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal
Pull thermal management fixes from Eduardo Valentin:
"Specifics:
- Several fixes in tmon tool.
- Fixes in intel int340x for _ART and _TRT tables.
- Add id for Avoton SoC into powerclamp driver.
- Fixes in RCAR thermal driver to remove race conditions and fix fail
path
- Fixes in TI thermal driver: removal of unnecessary code and build
fix if !CONFIG_PM_SLEEP
- Cleanups in exynos thermal driver
- Add stubs for include/linux/thermal.h. Now drivers using thermal
calls but that also work without CONFIG_THERMAL will be able to
compile for systems that don't care about thermal.
Note: I am sending this pull on Rui's behalf while he fixes issues in
his Linux box"
* 'fixes-for-4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
thermal: int340x_thermal: Ignore missing _ART, _TRT tables
thermal/intel_powerclamp: add id for Avoton SoC
tools/thermal: tmon: silence 'set but not used' warnings
tools/thermal: tmon: use pkg-config to determine library dependencies
tools/thermal: tmon: support cross-compiling
tools/thermal: tmon: add .gitignore
tools/thermal: tmon: fixup tui windowing calculations
tools/thermal: tmon: tui: don't hard-code dialog window size assumptions
tools/thermal: tmon: add min/max macros
tools/thermal: tmon: add --target-temp parameter
thermal: exynos: Clean-up code to use oneline entry for exynos compatible table
thermal: rcar: Make error and remove paths symmetrical with init
thermal: rcar: Fix race condition between init and interrupt
thermal: Introduce dummy functions when thermal is not defined
ti-soc-thermal: Delete an unnecessary check before the function call "cpufreq_cooling_unregister"
thermal: ti-soc-thermal: bandgap: Fix build warning if !CONFIG_PM_SLEEP
Linus Torvalds [Mon, 2 Mar 2015 22:03:27 +0000 (14:03 -0800)]
Merge tag 'md/4.0-fixes' of git://neil.brown.name/md
Pull md fixes from Neil Brown:
"Three md fixes:
- fix a read-balance problem that was reported 2 years ago, but that
I never noticed the report :-(
- fix for rare RAID6 problem causing incorrect bitmap updates when
two devices fail.
- add __ATTR_PREALLOC annotation now that it is possible"
* tag 'md/4.0-fixes' of git://neil.brown.name/md:
md: mark some attributes as pre-alloc
raid5: check faulty flag for array status during recovery.
md/raid1: fix read balance when a drive is write-mostly.
Linus Torvalds [Mon, 2 Mar 2015 22:02:17 +0000 (14:02 -0800)]
Merge tag 'metag-fixes-v4.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag
Pull arch/metag fix from James Hogan:
"This is just a single patch to fix the KSTK_EIP() and KSTK_ESP()
macros for metag which have always been erronously returning the PC
and stack pointer of the task's kernel context rather than from its
user context saved at entry from userland into the kernel, which
affects the contents of /proc/<pid>/maps and /proc/<pid>/stat"
* tag 'metag-fixes-v4.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag:
metag: Fix KSTK_EIP() and KSTK_ESP() macros
Tero Kristo [Fri, 27 Feb 2015 13:59:26 +0000 (15:59 +0200)]
ARM: OMAP4+: PRM: fix omap4 version of prm_save_and_clear_irqen
This was incorrectly reading the irq status registers during the save
and clear, instead of the irq enable. This worked because there is only
one user for the prcm interrupts currently, namely the io-chain. Whenever
the function was called, an io-chain interrupt was both pending and
enabled.
Signed-off-by: Tero Kristo <t-kristo@ti.com> Cc: Paul Walmsley <paul@pwsan.com> Cc: Tony Lindgren <tony@atomide.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
Deasserting hardreset increases the usecount for the hwmod parent clockdomain
always, however usecount is only decreased at end in certain error cases.
This causes software supervised clockdomains to remain always on, preventing
idle. Fixed by always releasing the hwmods clockdomain parent when exiting
the function.
Signed-off-by: Tero Kristo <t-kristo@ti.com> Tested-by: Carlos Hernandez <ceh@ti.com> Cc: Paul Walmsley <paul@pwsan.com> Cc: Tony Lindgren <tony@atomide.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
Linus Torvalds [Sun, 1 Mar 2015 20:22:44 +0000 (12:22 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"A CR4-shadow 32-bit init fix, plus two typo fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Init per-cpu shadow copy of CR4 on 32-bit CPUs too
x86/platform/intel-mid: Fix trivial printk message typo in intel_mid_arch_setup()
x86/cpu/intel: Fix trivial typo in intel_tlb_table[]
Linus Torvalds [Sun, 1 Mar 2015 19:56:13 +0000 (11:56 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Two kprobes fixes and a handful of tooling fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf tools: Make sparc64 arch point to sparc
perf symbols: Define EM_AARCH64 for older OSes
perf top: Fix SIGBUS on sparc64
perf tools: Fix probing for PERF_FLAG_FD_CLOEXEC flag
perf tools: Fix pthread_attr_setaffinity_np build error
perf tools: Define _GNU_SOURCE on pthread_attr_setaffinity_np feature check
perf bench: Fix order of arguments to memcpy_alloc_mem
kprobes/x86: Check for invalid ftrace location in __recover_probed_insn()
kprobes/x86: Use 5-byte NOP when the code might be modified by ftrace
locking/rtmutex: Set state back to running on error
The "usual" path is:
- rt_mutex_slowlock()
- set_current_state()
- task_blocks_on_rt_mutex() (ret 0)
- __rt_mutex_slowlock()
- sleep or not but do return with __set_current_state(TASK_RUNNING)
- back to caller.
In the early error case where task_blocks_on_rt_mutex() return
-EDEADLK we never change the task's state back to RUNNING. I
assume this is intended. Without this change after ww_mutex
using rt_mutex the selftest passes but later I get plenty of:
| bad: scheduling from the idle thread!
backtraces.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: Mike Galbraith <umgwanakikbuti@gmail.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Maarten Lankhorst <maarten.lankhorst@canonical.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: afffc6c1805d ("locking/rtmutex: Optimize setting task running after being blocked") Link: http://lkml.kernel.org/r/1425056229-22326-4-git-send-email-bigeasy@linutronix.de Signed-off-by: Ingo Molnar <mingo@kernel.org>
Linus Torvalds [Sat, 28 Feb 2015 18:36:48 +0000 (10:36 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Just general fixes: radeon, i915, atmel, tegra, amdkfd and one core
fix"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (28 commits)
drm: atmel-hlcdc: remove clock polarity from crtc driver
drm/radeon: only enable DP audio if the monitor supports it
drm/radeon: fix atom aux payload size check for writes (v2)
drm/radeon: fix 1 RB harvest config setup for TN/RL
drm/radeon: enable SRBM timeout interrupt on EG/NI
drm/radeon: enable SRBM timeout interrupt on SI
drm/radeon: enable SRBM timeout interrupt on CIK v2
drm/radeon: dump full IB if we hit a packet error
drm/radeon: disable mclk switching with 120hz+ monitors
drm/radeon: use drm_mode_vrefresh() rather than mode->vrefresh
drm/radeon: enable native backlight control on old macs
drm/i915: Fix frontbuffer false positve.
drm/i915: Align initial plane backing objects correctly
drm/i915: avoid processing spurious/shared interrupts in low-power states
drm/i915: Check obj->vma_list under the struct_mutex
drm/i915: Fix a use after free, and unbalanced refcounting
drm: atmel-hlcdc: remove useless pm_runtime_put_sync in probe
drm: atmel-hlcdc: reset layer A2Q and UPDATE bits when disabling it
drm: Fix deadlock due to getconnector locking changes
drm/i915: Dell Chromebook 11 has PWM backlight
...
Linus Torvalds [Sat, 28 Feb 2015 18:06:33 +0000 (10:06 -0800)]
Merge tag 'xfs-for-linus-4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs
Pull xfs fixes from Dave Chinner:
"These are fixes for regressions/bugs introduced in the 4.0 merge cycle
and problems discovered during the merge window that need to be pushed
back to stable kernels ASAP.
This contains:
- ensure quota type is reset in on-disk dquots
- fix missing partial EOF block data flush on truncate extension
- fix transaction leak in error handling for new pnfs block layout
support
- add missing target_ip check to RENAME_EXCHANGE"
* tag 'xfs-for-linus-4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs:
xfs: cancel failed transaction in xfs_fs_commit_blocks()
xfs: Ensure we have target_ip for RENAME_EXCHANGE
xfs: ensure truncate forces zeroed blocks to disk
xfs: Fix quota type in quota structures when reusing quota file
Core mm expects __PAGETABLE_{PUD,PMD}_FOLDED to be defined if these page
table levels folded. Usually, these defines are provided by
<asm-generic/pgtable-nopmd.h> and <asm-generic/pgtable-nopud.h>.
But some architectures fold page table levels in a custom way. They
need to define these macros themself. This patch adds missing defines.
The patch fixes mm->nr_pmds underflow and eliminates dead __pmd_alloc()
and __pud_alloc() on architectures without these page table levels.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Aaro Koskinen <aaro.koskinen@iki.fi> Cc: David Howells <dhowells@redhat.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Helge Deller <deller@gmx.de> Cc: "James E.J. Bottomley" <jejb@parisc-linux.org> Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Historically, !__GFP_FS allocations were not allowed to invoke the OOM
killer once reclaim had failed, but nevertheless kept looping in the
allocator.
Commit 9879de7373fc ("mm: page_alloc: embed OOM killing naturally into
allocation slowpath"), which should have been a simple cleanup patch,
accidentally changed the behavior to aborting the allocation at that
point. This creates problems with filesystem callers (?) that currently
rely on the allocator waiting for other tasks to intervene.
Revert the behavior as it shouldn't have been changed as part of a
cleanup patch.
Fixes: 9879de7373fc ("mm: page_alloc: embed OOM killing naturally into allocation slowpath") Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Michal Hocko <mhocko@suse.cz> Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Cc: Theodore Ts'o <tytso@mit.edu> Cc: Dave Chinner <david@fromorbit.com> Acked-by: David Rientjes <rientjes@google.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Mel Gorman <mgorman@suse.de> Cc: <stable@vger.kernel.org> [3.19.x] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joonsoo Kim [Fri, 27 Feb 2015 23:52:01 +0000 (15:52 -0800)]
zram: use proper type to update max_used_pages
max_used_pages is defined as atomic_long_t so we need to use unsigned
long to keep temporary value for it rather than int which is smaller
than unsigned long in a 64 bit system.
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Jerome Marchand <jmarchan@redhat.com> Cc: Nitin Gupta <ngupta@vflare.org> Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joshua Kinard [Fri, 27 Feb 2015 23:51:59 +0000 (15:51 -0800)]
drivers/rtc/rtc-ds1685.c: fix conditional in ds1685_rtc_sysfs_time_regs_{show,store}
Fix a conditional statement checking for NULL in both
ds1685_rtc_sysfs_time_regs_show and ds1685_rtc_sysfs_time_regs_store
that was using a logical AND when it should be using a logical OR so
that we fail out of the function properly if the condition ever
evaluates to true.
Fixes: aaaf5fbf56f1 ("rtc: add driver for DS1685 family of real time clocks") Signed-off-by: Joshua Kinard <kumba@gentoo.org> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ryusuke Konishi [Fri, 27 Feb 2015 23:51:56 +0000 (15:51 -0800)]
nilfs2: fix potential memory overrun on inode
Each inode of nilfs2 stores a root node of a b-tree, and it turned out to
have a memory overrun issue:
Each b-tree node of nilfs2 stores a set of key-value pairs and the number
of them (in "bn_nchildren" member of nilfs_btree_node struct), as well as
a few other "bn_*" members.
Since the value of "bn_nchildren" is used for operations on the key-values
within the b-tree node, it can cause memory access overrun if a large
number is incorrectly set to "bn_nchildren".
For instance, nilfs_btree_node_lookup() function determines the range of
binary search with it, and too large "bn_nchildren" leads
nilfs_btree_node_get_key() in that function to overrun.
As for intermediate b-tree nodes, this is prevented by a sanity check
performed when each node is read from a drive, however, no sanity check
has been done for root nodes stored in inodes.
This patch fixes the issue by adding missing sanity check against b-tree
root nodes so that it's called when on-memory inodes are read from ifile,
inode metadata file.
This got lost during the initial merge process: Python requires an
__init__.py script, even if empty, in order to accept a directory as
package. Add it, this time as a non-empty file.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rtc: ds1685: remove superfluous checks for out-of-range u8 values
drivers/rtc/rtc-ds1685.c: In function `ds1685_rtc_read_alarm':
drivers/rtc/rtc-ds1685.c:402: warning: comparison is always true due to limited range of data type
drivers/rtc/rtc-ds1685.c:409: warning: comparison is always true due to limited range of data type
drivers/rtc/rtc-ds1685.c:416: warning: comparison is always true due to limited range of data type
drivers/rtc/rtc-ds1685.c: In function `ds1685_rtc_set_alarm':
drivers/rtc/rtc-ds1685.c:475: warning: comparison is always true due to limited range of data type
drivers/rtc/rtc-ds1685.c:478: warning: comparison is always true due to limited range of data type
drivers/rtc/rtc-ds1685.c:481: warning: comparison is always true due to limited range of data type
u8 cannot contain a value larger than 0xff, hence drop the checks.
Wrapping the checks in unlikely() indicated some sense of humor, though ;-)
The newly added ds1685 driver causes a build error when enabled without
CONFIG_RTC_INTF_DEV:
drivers/rtc/rtc-ds1685.c:919:22: error: 'ds1685_rtc_alarm_irq_enable' undeclared here (not in a function)
.alarm_irq_enable = ds1685_rtc_alarm_irq_enable,
Apparently the driver was incorrectly changed to reflect the interface
change from 16380c153a69c ("RTC: Convert rtc drivers to use the
alarm_irq_enable method"), which removed the respective #ifdef from all
other rtc drivers.
This does the same change that was merged for the other drivers before and
removes the #ifdef, allowing the interrupts to be enabled through the
in-kernel rtc interface independent of the existence of /dev/rtc.
Fixes: aaaf5fbf56f ("rtc: add driver for DS1685 family of real time clocks") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Joshua Kinard <kumba@gentoo.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Hocko [Fri, 27 Feb 2015 23:51:46 +0000 (15:51 -0800)]
memcg: fix low limit calculation
A memcg is considered low limited even when the current usage is equal to
the low limit. This leads to interesting side effects e.g.
groups/hierarchies with no memory accounted are considered protected and
so the reclaim will emit MEMCG_LOW event when encountering them.
Another and much bigger issue was reported by Joonsoo Kim. He has hit a
NULL ptr dereference with the legacy cgroup API which even doesn't have
low limit exposed. The limit is 0 by default but the initial check fails
for memcg with 0 consumption and parent_mem_cgroup() would return NULL if
use_hierarchy is 0 and so page_counter_read would try to dereference NULL.
I suppose that the current implementation is just an overlook because the
documentation in Documentation/cgroups/unified-hierarchy.txt says:
"The memory.low boundary on the other hand is a top-down allocated
reserve. A cgroup enjoys reclaim protection when it and all its
ancestors are below their low boundaries"
Fix the usage and the low limit comparision in mem_cgroup_low accordingly.
Fixes: 241994ed8649 (mm: memcontrol: default hierarchy interface for memory) Reported-by: Joonsoo Kim <js1304@gmail.com> Signed-off-by: Michal Hocko <mhocko@suse.cz> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joonsoo Kim [Fri, 27 Feb 2015 23:51:43 +0000 (15:51 -0800)]
mm/nommu: fix memory leak
Maxime reported the following memory leak regression due to commit dbc8358c7237 ("mm/nommu: use alloc_pages_exact() rather than its own
implementation").
On v3.19, I am facing a memory leak. Each time I run a command one page
is lost. Here an example with busybox's free command:
/ # free
total used free shared buffers cached
Mem: 7928 1972 5956 0 0 492
-/+ buffers/cache: 1480 6448
/ # free
total used free shared buffers cached
Mem: 7928 1976 5952 0 0 492
-/+ buffers/cache: 1484 6444
/ # free
total used free shared buffers cached
Mem: 7928 1980 5948 0 0 492
-/+ buffers/cache: 1488 6440
/ # free
total used free shared buffers cached
Mem: 7928 1984 5944 0 0 492
-/+ buffers/cache: 1492 6436
/ # free
total used free shared buffers cached
Mem: 7928 1988 5940 0 0 492
-/+ buffers/cache: 1496 6432
At some point, the system fails to sastisfy 256KB allocations:
This problem happens because we allocate ordered page through
__get_free_pages() in do_mmap_private() in some cases and we try to free
individual pages rather than ordered page in free_page_series(). In
this case, freeing pages whose refcount is not 0 won't be freed to the
page allocator so memory leak happens.
To fix the problem, this patch changes __get_free_pages() to
alloc_pages_exact() since alloc_pages_exact() returns
physically-contiguous pages but each pages are refcounted.
Fixes: dbc8358c7237 ("mm/nommu: use alloc_pages_exact() rather than its own implementation"). Reported-by: Maxime Coquelin <mcoquelin.stm32@gmail.com> Tested-by: Maxime Coquelin <mcoquelin.stm32@gmail.com> Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: <stable@vger.kernel.org> [3.19] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The following patch updates the Ocfs2 documentation in MAINTAINERS,
ocfs2.txt, and dlmfs.txt. I added our new official web page, changed
the location of our tools git tree and removed the link to Joel's
ancient kernel git tree - Andrew has handled our patches for a while
now.
Signed-off-by: Mark Fasheh <mfasheh@suse.de> Cc: Joel Becker <jlbec@evilplan.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Steven Rostedt [Fri, 27 Feb 2015 19:50:19 +0000 (14:50 -0500)]
x86: Init per-cpu shadow copy of CR4 on 32-bit CPUs too
Commit:
1e02ce4cccdc ("x86: Store a per-cpu shadow copy of CR4")
added a shadow CR4 such that reads and writes that do not
modify the CR4 execute much faster than always reading the
register itself.
The change modified cpu_init() in common.c, so that the
shadow CR4 gets initialized before anything uses it.
Unfortunately, there's two cpu_init()s in common.c. There's
one for 64-bit and one for 32-bit. The commit only added
the shadow init to the 64-bit path, but the 32-bit path
needs the init too.
It is possible that _ART/_TRT tables are missing or have errors.
Ignore those failures, as INT3400 thermal zone is still required
for _OSC or mode switch.
Enable Intel Powerclamp driver on Atom* Processor C2000 Product
Family for Microservers (Avoton). Avoton - SoCs for micro-servers
has package C-states which can be used for idle injection.
Reported-by: Jose Navarro <jose.navarro@intel.com> Suggested-by: Jacob Pan <jacob.jun.pan@linux.intel.com> Tested-by: Jose Carlos Venegas Munoz <jos.c.venegas.munoz@intel.com> Signed-off-by: Miguel Bernal Marin <miguel.bernal.marin@linux.intel.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Brian Norris [Wed, 18 Feb 2015 02:18:36 +0000 (18:18 -0800)]
tools/thermal: tmon: silence 'set but not used' warnings
gcc complains about the 'cols' variable being unused. This is
unavoidable, given the ncurses getmaxyx() macro-based API, which wants
to assign to a variable directly, even when we're not going to use it.
Warning:
gcc -O1 -Wall -Wshadow -W -Wformat -Wimplicit-function-declaration -Wimplicit-int -fstack-protector -D VERSION=\"1.0\" -c -o tui.o tui.c
tui.c: In function ‘show_dialogue’:
tui.c:288:12: warning: variable ‘cols’ set but not used [-Wunused-but-set-variable]
int rows, cols;
^
So, add a hack to get rid of that warning.
Signed-off-by: Brian Norris <computersforpeace@gmail.com> Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Brian Norris [Wed, 18 Feb 2015 02:18:35 +0000 (18:18 -0800)]
tools/thermal: tmon: use pkg-config to determine library dependencies
Some distros (e.g., Arch Linux) don't package the tinfo library
separately from ncurses, so don't unconditionally include it. Instead,
use pkg-config.
The $(STATIC) ugliness is to handle the reported build case from commit 6b533269fb25 ("tools/thermal: tmon: fix compilation errors when building
statically"), where a developer wants to be able to build with:
make LDFLAGS=-static
which requires an additional pkg-config flag.
Finally, support a lowest common denominator fallback (-lpanel
-lncurses) for build systems that don't have pkg-config entries for
ncurses.
Signed-off-by: Brian Norris <computersforpeace@gmail.com> Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The number of rows in the dialog vary according to the number of cooling
devices. However, some of the windowing computations were assuming a
fixed number of rows. This computation is OK when we have between 4 and
9 cooling devices (and they wrap to the next column), but with fewer
devices, we end up printing off the end of the window.
This unifies the row computation into a single function and uses that
throughout the TUI code. This also accounts for increasing the number of
rows when there are more than 9 total cooling devices.
Signed-off-by: Brian Norris <computersforpeace@gmail.com> Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Brian Norris [Wed, 18 Feb 2015 02:18:29 +0000 (18:18 -0800)]
tools/thermal: tmon: add --target-temp parameter
If we launch in daemon mode (--daemon), we don't have the ncurses UI,
but we might want to set the target temperature still. For example,
someone might stick the following in their boot script:
Linus Torvalds [Sat, 28 Feb 2015 00:18:33 +0000 (16:18 -0800)]
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"The arm-soc bug fixes this time around are mostly for the omap
platform, coming from a pull request from Tony Lindgren and are almost
entirely fixing dts files.
The other two changes enable support for the shmobile platform in
generic armv7 kernels and change some properties in the ARM64
reference board dts files"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: multi_v7_defconfig: Enable shmobile platforms
arm64: Add L2 cache topology to ARM Ltd boards/models
ARM: dts: am335x-bone*: usb0 is hardwired for peripheral
ARM: dts: dra7x-evm: beagle-x15: Fix USB Host
ARM: omap2plus_defconfig: Fix SATA boot
ARM: omap2plus_defconfig: Enable OMAP NAND BCH driver
ARM: dts: dra7: Correct the dma controller's property names
ARM: dts: omap5: Correct the dma controller's property names
ARM: dts: omap4: Correct the dma controller's property names
ARM: dts: omap3: Correct the dma controller's property names
ARM: dts: omap2: Correct the dma controller's property names
ARM: dts: am437x-idk: fix sleep pinctrl state
ARM: omap2plus_defconfig: enable TPS62362 regulator
ARM: dts: am437x-idk: fix TPS62362 i2c bus
ARM: dts: n900: Fix offset for smc91x ethernet
ARM: dts: n900: fix i2c bus numbering
ARM: dts: Fix USB dts configuration for dm816x
ARM: dts: OMAP5: Fix SATA PHY node
ARM: dts: DRA7: Fix SATA PHY node
Linus Torvalds [Sat, 28 Feb 2015 00:09:37 +0000 (16:09 -0800)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
"Various arm64 fixes:
- ftrace branch generation fix
- branch instruction encoding fix
- include files, guards and unused prototypes clean-up
- minor VDSO ABI fix (clock_getres)
- PSCI functions moved to .S to avoid compilation error with gcc 5
- pte_modify fix to not ignore the mapping type
- crypto: AES interleaved increased to 4x (for performance reasons)
- text patching fix for modules
- swiotlb increased back to 64MB
- copy_siginfo_to_user32() fix for big endian"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: cpuidle: add asm/proc-fns.h inclusion
arm64: compat Fix siginfo_t -> compat_siginfo_t conversion on big endian
arm64: Increase the swiotlb buffer size 64MB
arm64: Fix text patching logic when using fixmap
arm64: crypto: increase AES interleave to 4x
arm64: enable PTE type bit in the mask for pte_modify
arm64: mm: remove unused functions and variable protoypes
arm64: psci: move psci firmware calls out of line
arm64: vdso: minor ABI fix for clock_getres
arm64: guard asm/assembler.h against multiple inclusions
arm64: insn: fix compare-and-branch encodings
arm64: ftrace: fix ftrace_modify_graph_caller for branch replace
Linus Torvalds [Sat, 28 Feb 2015 00:08:45 +0000 (16:08 -0800)]
Merge tag 'renesas-sh-drivers-for-v4.0' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas
Pull SH driver fix from Simon Horman:
"Disable PM runtime for multi-platform r8a7740 with genpd"
* tag 'renesas-sh-drivers-for-v4.0' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
drivers: sh: Disable PM runtime for multi-platform r8a7740 with genpd
ARM64 CPUidle driver requires the cpu_do_idle function so that it can
be used to enter the shallowest idle state, and it is declared in
asm/proc-fns.h.
The current ARM64 CPUidle driver does not include asm/proc-fns.h
explicitly and it has so far relied on implicit inclusion from other
header files.
Owing to some header dependencies reshuffling this currently triggers
build failures when CONFIG_ARM64_64K_PAGES=y:
drivers/cpuidle/cpuidle-arm64.c: In function "arm64_enter_idle_state"
drivers/cpuidle/cpuidle-arm64.c:42:3: error: implicit declaration of
function "cpu_do_idle" [-Werror=implicit-function-declaration]
cpu_do_idle();
^
This patch adds the explicit inclusion of the asm/proc-fns.h header file
in the arm64 asm/cpuidle.h header file, so that the build breakage is fixed
and the required header inclusion is added to the appropriate arch back-end
CPUidle header, already included by the CPUidle arm64 driver, where
CPUidle arch related function declarations belong.
Reported-by: Laura Abbott <lauraa@codeaurora.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Acked-by: Will Deacon <will.deacon@arm.com> Tested-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Catalin Marinas [Mon, 23 Feb 2015 15:13:40 +0000 (15:13 +0000)]
arm64: compat Fix siginfo_t -> compat_siginfo_t conversion on big endian
The native (64-bit) sigval_t union contains sival_int (32-bit) and
sival_ptr (64-bit). When a compat application invokes a syscall that
takes a sigval_t value (as part of a larger structure, e.g.
compat_sys_mq_notify, compat_sys_timer_create), the compat_sigval_t
union is converted to the native sigval_t with sival_int overlapping
with either the least or the most significant half of sival_ptr,
depending on endianness. When the corresponding signal is delivered to a
compat application, on big endian the current (compat_uptr_t)sival_ptr
cast always returns 0 since sival_int corresponds to the top part of
sival_ptr. This patch fixes copy_siginfo_to_user32() so that sival_int
is copied to the compat_siginfo_t structure.
Catalin Marinas [Thu, 5 Feb 2015 18:01:53 +0000 (18:01 +0000)]
arm64: Increase the swiotlb buffer size 64MB
With commit 3690951fc6d4 (arm64: Use swiotlb late initialisation), the
swiotlb buffer size is limited to MAX_ORDER_NR_PAGES. However, there are
platforms with 32-bit only devices that require bounce buffering via
swiotlb. This patch changes the swiotlb initialisation to an early 64MB
memblock allocation. In order to get the swiotlb buffer correctly
allocated (via memblock_virt_alloc_low_nopanic), this patch also defines
ARCH_LOW_ADDRESS_LIMIT to the maximum physical address capable of 32-bit
DMA.
Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com> Tested-by: Kefeng Wang <wangkefeng.wang@huawei.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Dave Airlie [Fri, 27 Feb 2015 00:31:40 +0000 (10:31 +1000)]
Merge branch 'drm-atmel-hlcdc-fixes' of git://github.com/bbrezillon/linux-at91 into drm-fixes
minor atmel hclcdc fixes.
* 'drm-atmel-hlcdc-fixes' of git://github.com/bbrezillon/linux-at91:
drm: atmel-hlcdc: remove clock polarity from crtc driver
drm: atmel-hlcdc: remove useless pm_runtime_put_sync in probe
drm: atmel-hlcdc: reset layer A2Q and UPDATE bits when disabling it
Dave Airlie [Fri, 27 Feb 2015 00:30:07 +0000 (10:30 +1000)]
Merge tag 'drm-intel-fixes-2015-02-26' of git://anongit.freedesktop.org/drm-intel into drm-fixes
First batch of fixes for v4.0-rc, plenty of cc: stable material.
* tag 'drm-intel-fixes-2015-02-26' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Fix frontbuffer false positve.
drm/i915: Align initial plane backing objects correctly
drm/i915: avoid processing spurious/shared interrupts in low-power states
drm/i915: Check obj->vma_list under the struct_mutex
drm/i915: Fix a use after free, and unbalanced refcounting
drm/i915: Dell Chromebook 11 has PWM backlight
drm/i915/skl: handle all pixel formats in skylake_update_primary_plane()
drm/i915/bdw: PCI IDs ending in 0xb are ULT.
Dave Airlie [Fri, 27 Feb 2015 00:29:14 +0000 (10:29 +1000)]
Merge branch 'drm-fixes-4.0' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
misc radeon fixes.
* 'drm-fixes-4.0' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: only enable DP audio if the monitor supports it
drm/radeon: fix atom aux payload size check for writes (v2)
drm/radeon: fix 1 RB harvest config setup for TN/RL
drm/radeon: enable SRBM timeout interrupt on EG/NI
drm/radeon: enable SRBM timeout interrupt on SI
drm/radeon: enable SRBM timeout interrupt on CIK v2
drm/radeon: dump full IB if we hit a packet error
drm/radeon: disable mclk switching with 120hz+ monitors
drm/radeon: use drm_mode_vrefresh() rather than mode->vrefresh
drm/radeon: enable native backlight control on old macs
Linus Torvalds [Thu, 26 Feb 2015 23:23:02 +0000 (15:23 -0800)]
Merge tag 'hwmon-for-linus-v4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fix from Guenter Roeck:
"Add missing return value check to ads7828 driver"
* tag 'hwmon-for-linus-v4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (ads7828) Check return value of devm_regmap_init_i2c
Linus Torvalds [Thu, 26 Feb 2015 18:55:19 +0000 (10:55 -0800)]
Merge tag 'sound-4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Most of changes in this pull request are about the fixes of crash of
FireWire drivers at hot-unplugging. In addition, there are a few
HD-audio fixes (removal of wrong static, a pin quirk for an ASUS mobo,
a regression fix for runtime PM on Panther Point) and a long-standing
(but fairly minor) bug of PCM core"
* tag 'sound-4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Disable runtime PM for Panther Point again
ALSA: hda: controller code - do not export static functions
ALSA: pcm: Don't leave PREPARED state after draining
ALSA: fireworks/bebob/dice/oxfw: make it possible to shutdown safely
ALSA: fireworks/bebob/dice/oxfw: allow stream destructor after releasing runtime
ALSA: firewire-lib: remove reference counting
ALSA: fireworks/bebob/dice/oxfw: add reference-counting for FireWire unit
ALSA: hda - Add pin configs for ASUS mobo with IDT 92HD73XX codec
ALSA: firewire-lib: fix an unexpected byte sequence for micro sign
Marc Zyngier [Tue, 24 Feb 2015 16:30:21 +0000 (16:30 +0000)]
arm64: Fix text patching logic when using fixmap
Patch 2f896d586610 ("arm64: use fixmap for text patching") changed
the way we patch the kernel text, using a fixmap when the kernel or
modules are flagged as read only.
Unfortunately, a flaw in the logic makes it fall over when patching
modules without CONFIG_DEBUG_SET_MODULE_RONX enabled:
This is triggered by the use of virt_to_page() on a module address,
which ends to pointing to Nowhereland if you're lucky, or corrupt
your precious data if not.
This patch fixes the logic by mimicking what is done on arm:
- If we're patching a module and CONFIG_DEBUG_SET_MODULE_RONX is set,
use vmalloc_to_page().
- If we're patching the kernel and CONFIG_DEBUG_RODATA is set,
use virt_to_page().
- Otherwise, use the provided address, as we can write to it directly.
Tested on 4.0-rc1 as a KVM guest.
Reported-by: Richard W.M. Jones <rjones@redhat.com> Reviewed-by: Kees Cook <keescook@chromium.org> Acked-by: Mark Rutland <mark.rutland@arm.com> Acked-by: Laura Abbott <lauraa@codeaurora.org> Tested-by: Richard W.M. Jones <rjones@redhat.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Linus Torvalds [Thu, 26 Feb 2015 18:34:24 +0000 (10:34 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fix from Chris Mason:
"I'm still testing more fixes, but I wanted to get out the fix for the
btrfs raid5/6 memory corruption I mentioned in my merge window pull"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix allocation size calculations in alloc_btrfs_bio
Ard Biesheuvel [Thu, 19 Feb 2015 17:25:16 +0000 (17:25 +0000)]
arm64: crypto: increase AES interleave to 4x
This patch increases the interleave factor for parallel AES modes
to 4x. This improves performance on Cortex-A57 by ~35%. This is
due to the 3-cycle latency of AES instructions on the A57's
relatively deep pipeline (compared to Cortex-A53 where the AES
instruction latency is only 2 cycles).
At the same time, disable inline expansion of the core AES functions,
as the performance benefit of this feature is negligible.
Measured on AMD Seattle (using tcrypt.ko mode=500 sec=1):
Baseline (2x interleave, inline expansion)
------------------------------------------
testing speed of async cbc(aes) (cbc-aes-ce) decryption
test 4 (128 bit key, 8192 byte blocks): 95545 operations in 1 seconds
test 14 (256 bit key, 8192 byte blocks): 68496 operations in 1 seconds
This patch (4x interleave, no inline expansion)
-----------------------------------------------
testing speed of async cbc(aes) (cbc-aes-ce) decryption
test 4 (128 bit key, 8192 byte blocks): 124735 operations in 1 seconds
test 14 (256 bit key, 8192 byte blocks): 92328 operations in 1 seconds
Feng Kan [Tue, 24 Feb 2015 23:40:21 +0000 (15:40 -0800)]
arm64: enable PTE type bit in the mask for pte_modify
Caught during Trinity testing. The pte_modify does not allow
modification for PTE type bit. This cause the test to hang
the system. It is found that the PTE can't transit from an
inaccessible page (b00) to a valid page (b11) because the mask
does not allow it. This happens when a big block of mmaped
memory is set the PROT_NONE, then the a small piece is broken
off and set to PROT_WRITE | PROT_READ cause a huge page split.
Signed-off-by: Feng Kan <fkan@apm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Yingjoe Chen [Wed, 25 Feb 2015 02:47:45 +0000 (10:47 +0800)]
arm64: mm: remove unused functions and variable protoypes
The functions __cpu_flush_user_tlb_range and __cpu_flush_kern_tlb_range
were removed in commit fa48e6f780 'arm64: mm: Optimise tlb flush logic
where we have >4K granule'. Global variable cpu_tlb was never used in
arm64.
Will Deacon [Wed, 25 Feb 2015 12:10:35 +0000 (12:10 +0000)]
arm64: psci: move psci firmware calls out of line
An arm64 allmodconfig fails to build with GCC 5 due to __asmeq
assertions in the PSCI firmware calling code firing due to mcount
preambles breaking our assumptions about register allocation of function
arguments:
Nathan Lynch [Tue, 24 Feb 2015 23:21:07 +0000 (17:21 -0600)]
arm64: vdso: minor ABI fix for clock_getres
The vdso implementation of clock_getres currently returns 0 (success)
whenever a null timespec is provided by the caller, regardless of the
clock id supplied.
This behavior is incorrect. It should fall back to syscall when an
unrecognized clock id is passed, even when the timespec argument is
null. This ensures that clock_getres always returns an error for
invalid clock ids.
Enable support for shmobile platforms that became multi-platform aware.
Several non-critical drivers and subsystems are built as modules, to keep
kernel size reasonable.
Fixed hwmod data for pcie by having the correct module mode offset.
Previously this module mode offset was part of pcie PHY which was wrong.
Now this module mode offset was moved to pcie hwmod and removed the hwmod data
for pcie phy. While at that renamed pcie_hwmod to pciess_hwmod in order
to match with the name given in TRM.
This helps to get rid of the following warning
"omap_hwmod: pcie1: _wait_target_disable failed"
[Grygorii.Strashko@linaro.org: Found the issue that actually caused
"omap_hwmod: pcie1: _wait_target_disable failed"] Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
Peter Ujfalusi [Thu, 26 Feb 2015 07:00:51 +0000 (00:00 -0700)]
ARM: omap2+: omap_hwmod: Set unique lock_class_key per hwmod
Add struct lock_class_key to omap_hwmod struct and use it to set unique
lockdep class per hwmod.
This will ensure that lockdep will know that each omap_hwmod->_lock should
be treated as separate class and will not give false warning about deadlock
or other issues due to nested use of hwmods.
DRA7x's ATL hwmod is one example for this since McASP can select ATL clock
as functional clock, which will trigger nested oh->_lock usage. This will
trigger false warning from lockdep validator as it is dealing with classes
and for it all hwmod clocks are the same class.
Suggested-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
Alex Deucher [Fri, 20 Feb 2015 16:51:38 +0000 (11:51 -0500)]
drm/radeon: fix atom aux payload size check for writes (v2)
The atom aux param interface only supports 4 bits for
the total write transfer size (header + payload). This
limits us to 12 bytes of payload rather than 16. Add a
check for this. Reads are not affected.
v2: switch to WARN_ON_ONCE
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Wed, 18 Feb 2015 05:59:45 +0000 (00:59 -0500)]
drm/radeon: disable mclk switching with 120hz+ monitors
These tend to be problematic even if the vblank period is
long enough. This needs more investigation across a wider
range of displays. Disable for now.
drm/radeon: enable native backlight control on old macs
Commit b7bc596ebbe0 ("drm/radeon: disable native
backlight control on pre-r6xx asics (v2)") accidently
broke backlight control on old mac laptops that use the
on-GPU backlight controller.
Signed-off-by: Nathan-J. Hirschauer <nathanhi@deepserve.info> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org
Adrian Hunter [Tue, 24 Feb 2015 11:20:59 +0000 (13:20 +0200)]
perf tools: Fix probing for PERF_FLAG_FD_CLOEXEC flag
Commit f6edb53c4993ffe92ce521fb449d1c146cea6ec2 converted the probe to
a CPU wide event first (pid == -1). For kernels that do not support
the PERF_FLAG_FD_CLOEXEC flag the probe fails with EINVAL. Since this
errno is not handled pid is not reset to 0 and the subsequent use of
pid = -1 as an argument brings in an additional failure path if
perf_event_paranoid > 0:
$ perf record -- sleep 1
perf_event_open(..., 0) failed unexpectedly with error 13 (Permission denied)
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.007 MB /tmp/perf.data (11 samples) ]
Also, ensure the fd of the confirmation check is closed and comment why
pid = -1 is used.
Needs to go to 3.18 stable tree as well.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Based-on-patch-by: David Ahern <david.ahern@oracle.com> Acked-by: David Ahern <david.ahern@oracle.com> Cc: David Ahern <dsahern@gmail.com> Link: http://lkml.kernel.org/r/54EC610C.8000403@intel.com Cc: stable@vger.kernel.org # v3.18+ Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Sudeep Holla [Wed, 21 Jan 2015 12:02:30 +0000 (12:02 +0000)]
arm64: Add L2 cache topology to ARM Ltd boards/models
Commit 5d425c18653731af6 ("arm64: kernel: add support for cpu cache
information") adds cacheinfo support for ARM64. Since there's no
architectural way of detecting the cpus that share particular cache,
device tree can be used and the core cacheinfo already supports the
same.
This patch adds the L2 cache topology on Juno board, FVP/RTSM and
foundation models.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Liviu Dudau <Liviu.Dudau@arm.com> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Feature detection for pthread_attr_setaffinity_np was failing, producing
this error:
In file included from bench/futex-hash.c:17:0:
bench/futex.h:73:19: error: conflicting types for ‘pthread_attr_setaffinity_np’
static inline int pthread_attr_setaffinity_np(pthread_attr_t *attr,
^
In file included from bench/futex.h:72:0,
from bench/futex-hash.c:17:
/usr/include/pthread.h:407:12: note: previous declaration of ‘pthread_attr_setaffinity_np’ was here
extern int pthread_attr_setaffinity_np (pthread_attr_t *__attr,
^
make[3]: *** [bench/futex-hash.o] Error 1
make[2]: *** [bench] Error 2
make[2]: *** Waiting for unfinished jobs....
This was because compiling test-pthread-attr-setaffinity-np.c
failed due to the function arguments:
test-pthread-attr-setaffinity-np.c: In function ‘main’:
test-pthread-attr-setaffinity-np.c:11:2: warning: null argument where non-null required (argument 3) [-Wnonnull]
ret = pthread_attr_setaffinity_np(&thread_attr, 0, NULL);
^
So fix the arguments.
Josh Boyer [Wed, 11 Feb 2015 16:24:05 +0000 (11:24 -0500)]
perf tools: Define _GNU_SOURCE on pthread_attr_setaffinity_np feature check
The man page for pthread_attr_set_affinity_np states that _GNU_SOURCE
must be defined before pthread.h is included in order to get the proper
function declaration. Define this in the Makefile.
Without this defined, the feature check fails on a Fedora system with
gcc5 and then the perf build later fails with conflicting prototypes for
the function.
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Vineet Gupta <Vineet.Gupta1@synopsys.com> Link: http://lkml.kernel.org/r/20150211162404.GA15522@hansolo.redhat.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Ingo Molnar [Wed, 25 Feb 2015 13:44:45 +0000 (14:44 +0100)]
Merge branch 'clockevents/4.0-rc1' of git://git.linaro.org/people/daniel.lezcano/linux into timers/urgent
Pull clockevents driver fixes from Daniel Lezcano:
- Fix the Kconfig to prevent the asm9260 timer to be compiled with
allyesconfig with sparc/sparc64 (Daniel Lezcano)
- Reorder the mtk driver init sequence in order to prevent a potential race
when the clock is registered before the irq handler is set (Matthias Brugger)
- Fix a section mismatch for the pxa driver (Robert Jarzmik)
Robert Jarzmik [Sat, 31 Jan 2015 22:40:40 +0000 (23:40 +0100)]
clocksource: pxa: Fix section mismatch
As pxa_timer_common_init() is only called in init context, mark it as
such, and quiesce the compiler warnings :
WARNING: vmlinux.o(.text.unlikely+0x45d4): Section mismatch in reference
from the function pxa_timer_common_init() to the function
.init.text:sched_clock_register()
WARNING: vmlinux.o(.text.unlikely+0x4610): Section mismatch in reference
from the function pxa_timer_common_init() to the function
.init.text:clocksource_mmio_init()
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
projects / mirror_ubuntu-disco-kernel.git / log