In gsm_cleanup_mux() the muxer is closed down and all queues are removed.
However, removing the queues is done without explicit control of the
underlying buffers. Flush those before freeing up our queues to ensure
that all outgoing queues are cleared consistently. Otherwise, a new mux
connection establishment attempt may time out while the underlying tty is
still busy sending out the remaining data from the previous connection.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline") Cc: stable@vger.kernel.org Signed-off-by: Daniel Starke <daniel.starke@siemens.com> Link: https://lore.kernel.org/r/20220414094225.4527-10-daniel.starke@siemens.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The current DLCI release order starts with the control channel followed by
the user channels. Reverse this order to keep the control channel open
until all user channels have been released.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline") Cc: stable@vger.kernel.org Signed-off-by: Daniel Starke <daniel.starke@siemens.com> Link: https://lore.kernel.org/r/20220414094225.4527-9-daniel.starke@siemens.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.7.2 states that the maximum frame size
(N1) refers to the length of the information field (i.e. user payload).
However, 'txframe' stores the whole frame including frame header, checksum
and start/end flags. We also need to consider the byte stuffing overhead.
Define constant for the protocol overhead and adjust the 'txframe' size
calculation accordingly to reserve enough space for a complete mux frame
including byte stuffing for advanced option mode. Note that no byte
stuffing is applied to the start and end flag.
Also use MAX_MTU instead of MAX_MRU as this buffer is used for data
transmission.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline") Cc: stable@vger.kernel.org Signed-off-by: Daniel Starke <daniel.starke@siemens.com> Link: https://lore.kernel.org/r/20220414094225.4527-8-daniel.starke@siemens.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Check if the incoming interface is available and NFT_BREAK
in case neither skb->sk nor input device are set.
Because nf_sk_lookup_slow*() assume packet headers are in the
'in' direction, use in postrouting is not going to yield a meaningful
result. Same is true for the forward chain, so restrict the use
to prerouting, input and output.
Use in output work if a socket is already attached to the skb.
Fixes: 554ced0a6e29 ("netfilter: nf_tables: add support for native socket matching") Reported-and-tested-by: Topi Miettinen <toiwoton@gmail.com> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The gsm_mux field 'malformed' represents the number of malformed frames
received. However, gsm1_receive() also increases this counter for any out
of frame byte.
Fix this by ignoring out of frame data for the malformed counter.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline") Cc: stable@vger.kernel.org Signed-off-by: Daniel Starke <daniel.starke@siemens.com> Link: https://lore.kernel.org/r/20220414094225.4527-7-daniel.starke@siemens.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.5.2 describes that the signal octet in
convergence layer type 2 can be either one or two bytes. The length is
encoded in the EA bit. This is set 1 for the last byte in the sequence.
gsmtty_modem_update() handles this correctly but gsm_dlci_data_output()
fails to set EA to 1. There is no case in which we encode two signal octets
as there is no case in which we send out a break signal.
Therefore, always set the EA bit to 1 for the signal octet to fix this.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline") Cc: stable@vger.kernel.org Signed-off-by: Daniel Starke <daniel.starke@siemens.com> Link: https://lore.kernel.org/r/20220414094225.4527-5-daniel.starke@siemens.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Internally, we manage the alive state of the mux channels and mux itself
with the field member 'dead'. This makes it possible to notify the user
if the accessed underlying link is already gone. On the other hand,
however, removing the virtual ttys before terminating the channels may
result in peer messages being received without any internal target. Move
the mux cleanup procedure from gsmld_detach_gsm() to gsmld_close() to fix
this by keeping the virtual ttys open until the mux has been cleaned up.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline") Cc: stable@vger.kernel.org Signed-off-by: Daniel Starke <daniel.starke@siemens.com> Link: https://lore.kernel.org/r/20220414094225.4527-4-daniel.starke@siemens.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The active mux instances are managed in the gsm_mux array and via mux_get()
and mux_put() functions separately. This gives a very loose coupling
between the actual instance and the gsm_mux array which manages it. It also
results in unnecessary lockings which makes it prone to failures. And it
creates a race condition if more than the maximum number of mux instances
are requested while the user changes the parameters of an active instance.
The user may loose ownership of the current mux instance in this case.
Fix this by moving the gsm_mux array handling to the mux allocation and
deallocation functions.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline") Cc: stable@vger.kernel.org Signed-off-by: Daniel Starke <daniel.starke@siemens.com> Link: https://lore.kernel.org/r/20220414094225.4527-3-daniel.starke@siemens.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.8.2 states that both sides will revert to
the non-multiplexed mode via a close-down message (CLD). The usual program
flow is as following:
- start multiplex mode by sending AT+CMUX to the mobile
- establish the control channel (DLCI 0)
- establish user channels (DLCI >0)
- terminate user channels
- send close-down message (CLD)
- revert to AT protocol (i.e. leave multiplexed mode)
The AT protocol is out of scope of the n_gsm driver. However,
gsm_disconnect() sends CLD if gsm_config() detects that the requested
parameters require the mux protocol to restart. The next immediate action
is to start the mux protocol by opening DLCI 0 again. Any responder side
which handles CLD commands correctly forces us to fail at this point
because AT+CMUX needs to be sent to the mobile to start the mux again.
Therefore, remove the CLD command in this phase and keep both sides in
multiplexed mode.
Remove the gsm_disconnect() function as it become unnecessary and merge the
remaining parts into gsm_cleanup_mux() to handle the termination order and
locking correctly.
Fixes: 71e077915396 ("tty: n_gsm: do not send/receive in ldisc close path") Cc: stable@vger.kernel.org Signed-off-by: Daniel Starke <daniel.starke@siemens.com> Link: https://lore.kernel.org/r/20220414094225.4527-2-daniel.starke@siemens.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Now arch-specific functions all do the same thing. When it fixes the
symbol address it needs to check the boundary between the kernel image
and modules. For the last symbol in the previous region, it cannot
know the exact size as it's discarded already. Thus it just uses a
small page size (4096) and rounds it up like the last symbol.
Fixes: 3cf6a32f3f2a4594 ("perf symbols: Fix symbol size calculation condition") Signed-off-by: Namhyung Kim <namhyung@kernel.org> Acked-by: Ian Rogers <irogers@google.com> Cc: Heiko Carstens <hca@linux.ibm.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Jiri Olsa <jolsa@kernel.org> Cc: John Garry <john.garry@huawei.com> Cc: Leo Yan <leo.yan@linaro.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mathieu Poirier <mathieu.poirier@linaro.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Michael Petlan <mpetlan@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Song Liu <songliubraving@fb.com> Cc: Will Deacon <will@kernel.org> Cc: linux-s390@vger.kernel.org Cc: linuxppc-dev@lists.ozlabs.org Link: https://lore.kernel.org/r/20220416004048.1514900-3-namhyung@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The symbol fixup is necessary for symbols in kallsyms since they don't
have size info. So we use the next symbol's address to calculate the
size. Now it's also used for user binaries because sometimes they miss
size for hand-written asm functions.
There's a arch-specific function to handle kallsyms differently but
currently it cannot distinguish kallsyms from others. Pass this
information explicitly to handle it properly. Note that those arch
functions will be moved to the generic function so I didn't added it to
the arch-functions.
Fixes: 3cf6a32f3f2a4594 ("perf symbols: Fix symbol size calculation condition") Signed-off-by: Namhyung Kim <namhyung@kernel.org> Acked-by: Ian Rogers <irogers@google.com> Cc: Heiko Carstens <hca@linux.ibm.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Jiri Olsa <jolsa@kernel.org> Cc: John Garry <john.garry@huawei.com> Cc: Leo Yan <leo.yan@linaro.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mathieu Poirier <mathieu.poirier@linaro.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Michael Petlan <mpetlan@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Song Liu <songliubraving@fb.com> Cc: Will Deacon <will@kernel.org> Cc: linux-s390@vger.kernel.org Cc: linuxppc-dev@lists.ozlabs.org Link: https://lore.kernel.org/r/20220416004048.1514900-2-namhyung@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When resuming from system sleep state, restore_processor_state()
restores the boot CPU MSRs. These MSRs could be emulated by microcode.
If microcode is not loaded yet, writing to emulated MSRs leads to
unchecked MSR access error:
The GW71xx, GW72xx and GW73xx boards have USB1 routed to a USB OTG
connectors and USB2 routed to a USB hub.
The OTG connector has a over-currently protection with an active-low
pin and the USB1 to HUB connection has no over-current protection (as
the HUB itself implements this for its downstream ports).
Add proper dt nodes to specify the over-current pin polarity for USB1
and disable over-current protection for USB2.
Fixes: 6f30b27c5ef5 ("arm64: dts: imx8mm: Add Gateworks i.MX 8M Mini Development Kits") Cc: stable@vger.kernel.org Signed-off-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Flexcom3 is used as board console serial. There are no pull-ups on these
lines on the board. This means that if a cable is not connected (that has
pull-ups included), stray characters could appear on the console as the
floating pins voltage levels are interpreted as incoming characters.
To avoid this problem, enable the internal pull-ups on these lines.
Fixes: 7540629e2fc7 ("ARM: dts: at91: add sama7g5 SoC DT and sama7g5-ek") Cc: stable@vger.kernel.org # v5.15+ Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com> Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Link: https://lore.kernel.org/r/20220307113827.2419331-1-eugen.hristev@microchip.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
On a zoned filesystem, if we fail to allocate the root node for the log
root tree while syncing the log, we end up returning without finishing
the IO plug we started before, resulting in leaking resources as we
have started writeback for extent buffers of a log tree before. That
allocation failure, which typically is either -ENOMEM or -ENOSPC, is not
fatal and the fsync can safely fallback to a full transaction commit.
So release the IO plug if we fail to allocate the extent buffer for the
root of the log root tree when syncing the log on a zoned filesystem.
Fixes: 3ddebf27fcd3a9 ("btrfs: zoned: reorder log node allocation on zoned filesystem") CC: stable@vger.kernel.org # 5.15+ Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Control Flow Integrity (CFI) instrumentation of the kernel noticed that
the caller, dev_attr_show(), and the callback, odvp_show(), did not have
matching function prototypes, which would cause a CFI exception to be
raised. Correct the prototype by using struct device_attribute instead
of struct kobj_attribute.
Reported-and-tested-by: Joao Moreira <joao@overdrivepizza.com> Link: https://lore.kernel.org/lkml/067ce8bd4c3968054509831fa2347f4f@overdrivepizza.com/ Fixes: 006f006f1e5c ("thermal/int340x_thermal: Export OEM vendor variables") Cc: 5.8+ <stable@vger.kernel.org> # 5.8+ Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The "safe state" index is used by acpi_idle_enter_bm() to avoid
entering a C-state that may require bus mastering to be disabled
on entry in the cases when this is not going to happen. For this
reason, it should not be set to point to C3 type of C-states, because
they may require bus mastering to be disabled on entry in principle.
This was broken by commit d6b88ce2eb9d ("ACPI: processor idle: Allow
playing dead in C3 state") which inadvertently allowed the "safe
state" index to point to C3 type of C-states.
This results in a machine that won't boot past the point when it first
enters C3. Restore the correct behaviour (either demote to C1/C2, or
use C3 but also set ARB_DIS=1).
I hit this on a Fujitsu Siemens Lifebook S6010 (P3) machine.
Fixes: d6b88ce2eb9d ("ACPI: processor idle: Allow playing dead in C3 state") Cc: 5.16+ <stable@vger.kernel.org> # 5.16+ Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Tested-by: Woody Suwalski <wsuwalski@gmail.com>
[ rjw: Subject and changelog adjustments ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
I made a mistake with the commit a6aaa0032424 ("net: ethernet: stmmac:
fix altr_tse_pcs function when using a fixed-link"). I should have
tested against both scenario of having a SGMII interface and one
without.
Without the SGMII PCS TSE adpater, the sgmii_adapter_base address is
NULL, thus a write to this address will fail.
Cc: stable@vger.kernel.org Fixes: a6aaa0032424 ("net: ethernet: stmmac: fix altr_tse_pcs function when using a fixed-link") Signed-off-by: Dinh Nguyen <dinguyen@kernel.org> Link: https://lore.kernel.org/r/20220420152345.27415-1-dinguyen@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
We have now seen panel (XMG Core 15 e21 laptop) advertizing support
for Intel proprietary eDP backlight control via DPCD registers, but
actually working only with legacy pwm control.
This patch adds panel EDID check for possible HDR static metadata and
Intel proprietary eDP backlight control is used only if that exists.
Missing HDR static metadata is ignored if user specifically asks for
Intel proprietary eDP backlight control via enable_dpcd_backlight
parameter.
v2 :
- Ignore missing HDR static metadata if Intel proprietary eDP
backlight control is forced via i915.enable_dpcd_backlight
- Printout info message if panel is missing HDR static metadata and
support for Intel proprietary eDP backlight control is detected
Fixes: 4a8d79901d5b ("drm/i915/dp: Enable Intel's HDR backlight interface (only SDR for now)") Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/5284 Cc: Lyude Paul <lyude@redhat.com> Cc: Mika Kahola <mika.kahola@intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Cc: Filippo Falezza <filippo.falezza@outlook.it> Cc: stable@vger.kernel.org Signed-off-by: Jouni Högander <jouni.hogander@intel.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220413082826.120634-1-jouni.hogander@intel.com Reviewed-by: Lyude Paul <lyude@redhat.com>
(cherry picked from commit b4b157577cb1de13bee8bebc3576f1de6799a921) Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The commit referenced below fixed packet re-routing if Netfilter mangles
a routing key property of a packet and the packet is routed in a VRF L3
domain. The fix, however, addressed IPv4 re-routing, only.
This commit applies the same behavior for IPv6. While at it, untangle
the nested ternary operator to make the code more readable.
Fixes: 6d8b49c3a3a3 ("netfilter: Update ip_route_me_harder to consider L3 domain") Cc: stable@vger.kernel.org Signed-off-by: Martin Willi <martin@strongswan.org> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This patch fixes a memory corruption that occurred in the
nand_scan() path for Hynix nand device.
On boot, for Hynix nand device will panic at a weird place:
| Unable to handle kernel NULL pointer dereference at virtual
address 00000070
| [00000070] *pgd=00000000
| Internal error: Oops: 5 [#1] PREEMPT SMP ARM
| Modules linked in:
| CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.17.0-01473-g13ae1769cfb0
#38
| Hardware name: Generic DT based system
| PC is at nandc_set_reg+0x8/0x1c
| LR is at qcom_nandc_command+0x20c/0x5d0
| pc : [<c088b74c>] lr : [<c088d9c8>] psr: 00000113
| sp : c14adc50 ip : c14ee208 fp : c0cc970c
| r10: 000000a3 r9 : 00000000 r8 : 00000040
| r7 : c16f6a00 r6 : 00000090 r5 : 00000004 r4 :c14ee040
| r3 : 00000000 r2 : 0000000b r1 : 00000000 r0 :c14ee040
| Flags: nzcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
| Control: 10c5387d Table: 8020406a DAC: 00000051
| Register r0 information: slab kmalloc-2k start c14ee000 pointer offset
64 size 2048
| Process swapper/0 (pid: 1, stack limit = 0x(ptrval))
| nandc_set_reg from qcom_nandc_command+0x20c/0x5d0
| qcom_nandc_command from nand_readid_op+0x198/0x1e8
| nand_readid_op from hynix_nand_has_valid_jedecid+0x30/0x78
| hynix_nand_has_valid_jedecid from hynix_nand_init+0xb8/0x454
| hynix_nand_init from nand_scan_with_ids+0xa30/0x14a8
| nand_scan_with_ids from qcom_nandc_probe+0x648/0x7b0
| qcom_nandc_probe from platform_probe+0x58/0xac
The problem is that the nand_scan()'s qcom_nand_attach_chip callback
is updating the nandc->max_cwperpage from 1 to 4 or 8 based on page size.
This causes the sg_init_table of clear_bam_transaction() in the driver's
qcom_nandc_command() to memset much more than what was initially
allocated by alloc_bam_transaction().
This patch will update nandc->max_cwperpage 1 to 4 or 8 based on page
size in qcom_nand_attach_chip call back after freeing the previously
allocated memory for bam txn as per nandc->max_cwperpage = 1 and then
again allocating bam txn as per nandc->max_cwperpage = 4 or 8 based on
page size in qcom_nand_attach_chip call back itself.
Cc: stable@vger.kernel.org Fixes: 6a3cec64f18c ("mtd: rawnand: qcom: convert driver to nand_scan()") Reported-by: Konrad Dybcio <konrad.dybcio@somainline.org> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Co-developed-by: Sricharan R <quic_srichara@quicinc.com> Signed-off-by: Sricharan R <quic_srichara@quicinc.com> Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/1650268107-5363-1-git-send-email-quic_mdalam@quicinc.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
kasan_quarantine_remove_cache() is called in kmem_cache_shrink()/
destroy(). The kasan_quarantine_remove_cache() call is protected by
cpuslock in kmem_cache_destroy() to ensure serialization with
kasan_cpu_offline().
However the kasan_quarantine_remove_cache() call is not protected by
cpuslock in kmem_cache_shrink(). When a CPU is going offline and cache
shrink occurs at same time, the cpu_quarantine may be corrupted by
interrupt (per_cpu_remove_cache operation).
So add a cpu_quarantine offline flags check in per_cpu_remove_cache().
[akpm@linux-foundation.org: add comment, per Zqiang]
Ensure that the i_flags field of struct zonefs_inode_info is cleared to
0 when initializing a zone file inode, avoiding seeing the flag
ZONEFS_ZONE_OPEN being incorrectly set.
Fixes: b5c00e975779 ("zonefs: open/close zone on file open/close") Cc: <stable@vger.kernel.org> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com> Reviewed-by: Hans Holmberg <hans.holmberg@wdc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The mount option "explicit_open" manages the device open zone
resources to ensure that if an application opens a sequential file for
writing, the file zone can always be written by explicitly opening
the zone and accounting for that state with the s_open_zones counter.
However, if some zones are already open when mounting, the device open
zone resource usage status will be larger than the initial s_open_zones
value of 0. Ensure that this inconsistency does not happen by closing
any sequential zone that is open when mounting.
Furthermore, with ZNS drives, closing an explicitly open zone that has
not been written will change the zone state to "closed", that is, the
zone will remain in an active state. Since this can then cause failures
of explicit open operations on other zones if the drive active zone
resources are exceeded, we need to make sure that the zone is not
active anymore by resetting it instead of closing it. To address this,
zonefs_zone_mgmt() is modified to change a REQ_OP_ZONE_CLOSE request
into a REQ_OP_ZONE_RESET for sequential zones that have not been
written.
Fixes: b5c00e975779 ("zonefs: open/close zone on file open/close") Cc: <stable@vger.kernel.org> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: Hans Holmberg <hans.holmberg@wdc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Because mremap does not have a MAP_FIXED_NOREPLACE flag, it can destroy
existing mappings. This causes a segfault when regions such as text are
remapped and the permissions are changed.
Verify the requested mremap destination address does not overlap any
existing mappings by using mmap's MAP_FIXED_NOREPLACE flag. Keep
incrementing the destination address until a valid mapping is found or
fail the current test once the max address is reached.
Link: https://lkml.kernel.org/r/20220420215721.4868-2-sidhartha.kumar@oracle.com Signed-off-by: Sidhartha Kumar <sidhartha.kumar@oracle.com> Reviewed-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Avoid calling mmap with requested addresses that are less than the
system's mmap_min_addr. When run as root, mmap returns EACCES when
trying to map addresses < mmap_min_addr. This is not one of the error
codes for the condition to retry the mmap in the test.
Rather than arbitrarily retrying on EACCES, don't attempt an mmap until
addr > vm.mmap_min_addr.
Add a munmap call after an alignment check as the mappings are retained
after the retry and can reach the vm.max_map_count sysctl.
Link: https://lkml.kernel.org/r/20220420215721.4868-1-sidhartha.kumar@oracle.com Signed-off-by: Sidhartha Kumar <sidhartha.kumar@oracle.com> Reviewed-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The "read_bhrb" global symbol is only called under CONFIG_PPC64 of
arch/powerpc/perf/core-book3s.c but it is compiled for both 32 and 64 bit
anyway (and LLVM fails to link this on 32bit).
This fixes it by moving bhrb.o to obj64 targets.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20220421025756.571995-1-aik@ozlabs.ru Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
We hold rrpriv->lock in position (1) of thread 1 and
use del_timer_sync() to wait timer to stop, but timer handler
also need rrpriv->lock in position (2) of thread 2.
As a result, rr_close() will block forever.
This patch extracts del_timer_sync() from the protection of
spin_lock_irqsave(), which could let timer handler to obtain
the needed lock.
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn> Link: https://lore.kernel.org/r/20220417125519.82618-1-duoming@zju.edu.cn Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
because the copychunk_write might cover a region of the file that has not yet
been sent to the server and thus fail.
A simple way to reproduce this is:
truncate -s 0 /mnt/testfile; strace -f -o x -ttT xfs_io -i -f -c 'pwrite 0k 128k' -c 'fcollapse 16k 24k' /mnt/testfile
the issue is that the 'pwrite 0k 128k' becomes rearranged on the wire with
the 'fcollapse 16k 24k' due to write-back caching.
fcollapse is implemented in cifs.ko as a SMB2 IOCTL(COPYCHUNK_WRITE) call
and it will fail serverside since the file is still 0b in size serverside
until the writes have been destaged.
To avoid this we must ensure that we destage any unwritten data to the
server before calling COPYCHUNK_WRITE.
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1997373 Reported-by: Xiaoli Feng <xifeng@redhat.com> Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The first "if" condition in __memcpy_flushcache is supposed to align the
"dest" variable to 8 bytes and copy data up to this alignment. However,
this condition may misbehave if "size" is greater than 4GiB.
The statement min_t(unsigned, size, ALIGN(dest, 8) - dest); casts both
arguments to unsigned int and selects the smaller one. However, the
cast truncates high bits in "size" and it results in misbehavior.
For example:
suppose that size == 0x100000001, dest == 0x200000002
min_t(unsigned, size, ALIGN(dest, 8) - dest) == min_t(0x1, 0xe) == 0x1;
...
dest += 0x1;
so we copy just one byte "and" dest remains unaligned.
This patch fixes the bug by replacing unsigned with size_t.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
print("with last bit removed")
for h_dest in h_dests:
hash = (h_dest ^ h_source ^ hproto ^ saddr ^ daddr)
hash ^= hash >> 16
hash ^= hash >> 8
hash = hash >> 1
print(hash)
Output:
$ python3.6 hash.py 522133332 522133333 <-------------- will result in both slaves being used
with last bit removed 261066666 261066666 <-------------- only single slave used
Signed-off-by: suresh kumar <suresh2514@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Currently ksmbd is using ->f_bsize from vfs_statfs() as sector size.
If fat/exfat is a local share, ->f_bsize is a cluster size that is too
large to be used as a sector size. Sector sizes larger than 4K cause
problem occurs when mounting an iso file through windows client.
The error message can be obtained using Mount-DiskImage command,
the error is:
"Mount-DiskImage : The sector size of the physical disk on which the
virtual disk resides is not supported."
This patch reports fixed 4KB sector size if ->s_blocksize is bigger
than 4KB.
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Add missing increment reference count of parent fp in
ksmbd_lookup_fd_inode().
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Reviewed-by: Hyunchul Lee <hyc.lee@gmail.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
We hold timer_lock in position (1) of thread 1 and
use del_timer_sync() to wait timer to stop, but timer handler
also need timer_lock in position (2) of thread 2.
As a result, rs_close() will block forever.
This patch deletes the redundant timer_lock in order to
prevent the deadlock. Because there is no race condition
between rs_close, rs_open and rs_poll.
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Message-Id: <20220407154430.22387-1-duoming@zju.edu.cn> Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
To solve this issue, we call 'ext4_unregister_sysfs() before flushing
s_error_work in ext4_put_super().
Signed-off-by: Ye Bin <yebin10@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Reviewed-by: Ritesh Harjani <riteshh@linux.ibm.com> Link: https://lore.kernel.org/r/20220322012419.725457-1-yebin10@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com> Link: https://lore.kernel.org/r/20220405121038.4094051-1-zheyuma97@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
// Send 2 data segments
+0 write(4, ..., 2000) = 2000
+0 > P. 1:2001(2000) ack 1
// TLP
+.022 > P. 1001:2001(1000) ack 1
// Continue to send 8 data segments
+0 write(4, ..., 10000) = 10000
+0 > P. 2001:10001(8000) ack 1
// RTO
+.188 > . 1:1001(1000) ack 1
// The original data is acked and new data is sent(F-RTO step 2.b)
+0 < . 1:1(0) ack 2001 win 257
+0 > P. 10001:12001(2000) ack 1
// D-SACK caused by TLP is regarded as a dupack, this results in
// the incorrect judgment of "loss was real"(F-RTO step 3.a)
+.022 < . 1:1(0) ack 2001 win 257 <sack 1001:2001,nop,nop>
// Never-retransmitted data(3001:4001) are acked and
// expect to switch to open state(F-RTO step 3.b)
+0 < . 1:1(0) ack 4001 win 257
+0 %{ assert tcpi_ca_state == 0, tcpi_ca_state }%
Fixes: e33099f96d99 ("tcp: implement RFC5682 F-RTO") Signed-off-by: Pengcheng Yang <yangpc@wangsu.com> Acked-by: Neal Cardwell <ncardwell@google.com> Tested-by: Neal Cardwell <ncardwell@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/1650967419-2150-1-git-send-email-yangpc@wangsu.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When client requests channel or ring size larger than what the server
can support the server will cap the request to the supported max. So,
the client would not be able to successfully request resources that
exceed the server limit.
Fixes: 723ad9161347 ("ibmvnic: Add ethtool private flag for driver-defined queue limits") Signed-off-by: Dany Madden <drt@linux.ibm.com> Link: https://lore.kernel.org/r/20220427235146.23189-1-drt@linux.ibm.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This patch corrects a bug whereby synthesized events from SPE
samples are missing virtual addresses.
Fixes: 54f7815efef7fad9 ("perf arm-spe: Fill address info for samples") Reviewed-by: Leo Yan <leo.yan@linaro.org> Signed-off-by: Timothy Hayes <timothy.hayes@arm.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: bpf@vger.kernel.org Cc: Jiri Olsa <jolsa@kernel.org> Cc: John Fastabend <john.fastabend@gmail.com> Cc: John Garry <john.garry@huawei.com> Cc: KP Singh <kpsingh@kernel.org> Cc: Leo Yan <leo.yan@linaro.org> Cc: linux-arm-kernel@lists.infradead.org Cc: Mark Rutland <mark.rutland@arm.com> Cc: Martin KaFai Lau <kafai@fb.com> Cc: Mathieu Poirier <mathieu.poirier@linaro.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: netdev@vger.kernel.org Cc: Song Liu <songliubraving@fb.com> Cc: Will Deacon <will@kernel.org> Cc: Yonghong Song <yhs@fb.com> Link: https://lore.kernel.org/r/20220421165205.117662-2-timothy.hayes@arm.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Commit 00bfe02f4796 ("gfs2: Fix mmap + page fault deadlocks for buffered
I/O") changed gfs2_file_read_iter() and gfs2_file_buffered_write() to
allow dropping the inode glock while faulting in user buffers. When the
lock was dropped, a short result was returned to indicate that the
operation was interrupted.
As pointed out by Linus (see the link below), this behavior is broken
and the operations should always re-acquire the inode glock and resume
the operation instead.
Link: https://lore.kernel.org/lkml/CAHk-=whaz-g_nOOoo8RRiWNjnv2R+h6_xk2F1J4TuSRxk1MtLw@mail.gmail.com/ Fixes: 00bfe02f4796 ("gfs2: Fix mmap + page fault deadlocks for buffered I/O") Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When direct writes fail with -ENOTBLK because we're writing into a
hole (gfs2_iomap_begin()) or because of a page invalidation failure
(iomap_dio_rw()), we're falling back to buffered writes. In that case,
when we lose the inode glock in gfs2_file_buffered_write(), we want to
re-acquire it instead of returning a short write.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Currently, instead of performing a short write,
iomap_file_buffered_write will fail when part of its iov iterator cannot
be read. In contrast, gfs2_file_buffered_write will loop around if it
can read part of the iov iterator, so we can end up in an endless loop.
This should be fixed in iomap_file_buffered_write (and also
generic_perform_write), but this comes a bit late in the 5.16
development cycle, so work around it in the filesystem by
trimming the iov iterator to the known-good size for now.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Put device node in error path in fec_enet_init_stop_mode().
Fixes: 8a448bf832af ("net: ethernet: fec: move GPR register offset and bit into DT") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20220426125231.375688-1-yangyingliang@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
While handling PCI errors (AER flow) driver tries to
disable NAPI [napi_disable()] after NAPI is deleted
[__netif_napi_del()] which causes unexpected system
hang/crash.
EEH calls into bnx2x twice based on the system log above, first through
bnx2x_io_error_detected() and then bnx2x_io_slot_reset(), and executes
the following call chains:
Calling tls_append_frag when max_open_record_len == record->len might
add an empty fragment to the TLS record if the call happens to be on the
page boundary. Normally tls_append_frag coalesces the zero-sized
fragment to the previous one, but not if it's on page boundary.
If a resync happens then, the mlx5 driver posts dump WQEs in
tx_post_resync_dump, and the empty fragment may become a data segment
with byte_count == 0, which will confuse the NIC and lead to a CQE
error.
This commit fixes the described issue by skipping tls_append_frag on
zero size to avoid adding empty fragments. The fix is not in the driver,
because an empty fragment is hardly the desired behavior.
Fixes: e8f69799810c ("net/tls: Add generic NIC offload infrastructure") Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Link: https://lore.kernel.org/r/20220426154949.159055-1-maximmi@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
dqm->gws_queue_count and pdd->qpd.mapped_gws_queue need to be updated
each time the queue gets evicted.
Fixes: b8020b0304c8 ("drm/amdkfd: Enable over-subscription with >1 GWS queue") Signed-off-by: David Yat Sin <david.yatsin@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
`nf_flowtable_udp_timeout` sysctl option is available only
if CONFIG_NFT_FLOW_OFFLOAD enabled. But infra for this flow
offload UDP timeout was added under CONFIG_NF_FLOW_TABLE
config option. So, if you have CONFIG_NFT_FLOW_OFFLOAD
disabled and CONFIG_NF_FLOW_TABLE enabled, the
`nf_flowtable_udp_timeout` is not present in sysfs.
Please note, that TCP flow offload timeout sysctl option
is present even CONFIG_NFT_FLOW_OFFLOAD is disabled.
I suppose it was a typo in commit that adds UDP flow offload
timeout and CONFIG_NF_FLOW_TABLE should be used instead.
Fixes: 975c57504da1 ("netfilter: conntrack: Introduce udp offload timeout configuration") Signed-off-by: Volodymyr Mytnyk <volodymyr.mytnyk@plvision.eu> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Commit 4b5923249b8fa4 ("net: dsa: lantiq_gswip: Configure all remaining
GSWIP_MII_CFG bits") added all known bits in the GSWIP_MII_CFGp
register. It helped bring this register into a well-defined state so the
driver has to rely less on the bootloader to do things right.
Unfortunately it also sets the GSWIP_MII_CFG_RMII_CLK bit without any
possibility to configure it. Upon further testing it turns out that all
boards which are supported by the GSWIP driver in OpenWrt which use an
RMII PHY have a dedicated oscillator on the board which provides the
50MHz RMII reference clock.
Don't set the GSWIP_MII_CFG_RMII_CLK bit (but keep the code which always
clears it) to fix support for the Fritz!Box 7362 SL in OpenWrt. This is
a board with two Atheros AR8030 RMII PHYs. With the "RMII clock" bit set
the MAC also generates the RMII reference clock whose signal then
conflicts with the signal from the oscillator on the board. This results
in a constant cycle of the PHY detecting link up/down (and as a result
of that: the two ports using the AR8030 PHYs are not working).
At the time of writing this patch there's no known board where the MAC
(GSWIP) has to generate the RMII reference clock. If needed this can be
implemented in future by providing a device-tree flag so the
GSWIP_MII_CFG_RMII_CLK bit can be toggled per port.
Fixes: 4b5923249b8fa4 ("net: dsa: lantiq_gswip: Configure all remaining GSWIP_MII_CFG bits") Tested-by: Jan Hoffmann <jan@3e8.eu> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Acked-by: Hauke Mehrtens <hauke@hauke-m.de> Link: https://lore.kernel.org/r/20220425152027.2220750-1-martin.blumenstingl@googlemail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
commit b4bdc4fbf8d0 ("soc: sunxi: Deal with the MBUS DMA offsets in a
central place") added a platform device notifier that sets the DMA
offset for all of the display engine frontend and backend devices.
The code applying the offset to DMA buffer physical addresses was then
removed from the backend driver in commit 756668ba682e ("drm/sun4i:
backend: Remove the MBUS quirks"), but the code subtracting PHYS_OFFSET
was left in the frontend driver.
As a result, the offset was applied twice in the frontend driver. This
likely went unnoticed because it only affects specific configurations
(scaling or certain pixel formats) where the frontend is used, on boards
with both one of these older SoCs and more than 1 GB of DRAM.
In addition, the references to PHYS_OFFSET prevent compiling the driver
on architectures where PHYS_OFFSET is not defined.
Fixes: b4bdc4fbf8d0 ("soc: sunxi: Deal with the MBUS DMA offsets in a central place") Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com> Signed-off-by: Samuel Holland <samuel@sholland.org> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://patchwork.freedesktop.org/patch/msgid/20220424162633.12369-4-samuel@sholland.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The other port_hidden functions rely on the port_read/port_write
functions to access the hidden control port. These functions apply the
offset for port_base_addr where applicable. Update port_hidden_wait to
use the port_wait_bit so that port_base_addr offsets are accounted for
when waiting for the busy bit to change.
Without the offset the port_hidden_wait function would timeout on
devices that have a non-zero port_base_addr (e.g. MV88E6141), however
devices that have a zero port_base_addr would operate correctly (e.g.
MV88E6390).
Fixes: 609070133aff ("net: dsa: mv88e6xxx: update code operating on hidden registers") Signed-off-by: Nathan Rossi <nathan@nathanrossi.com> Reviewed-by: Marek Behún <kabel@kernel.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20220425070454.348584-1-nathan@nathanrossi.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The hardware checksum offloading requires use of a transmit
status block inserted before the outgoing frame data, this was
updated in '9a9ba2a4aaaa ("net: bcmgenet: always enable status blocks")'
However, skb_tx_timestamp() assumes that it is passed a raw frame
and PTP parsing chokes on this status block.
Fix this by calling __skb_pull(), which hides the TSB before calling
skb_tx_timestamp(), so an outgoing PTP packet is parsed correctly.
As the data in the skb has already been set up for DMA, and the
dma_unmap_* calls use a separately stored address, there is no
no effective change in the data transmission.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20220424165307.591145-1-jonathan.lemon@gmail.com Fixes: d03825fba459 ("net: bcmgenet: add skb_tx_timestamp call") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
It's noted that dcvs interrupts are not self-clearing, thus an interrupt
handler runs constantly, which leads to a severe regression in runtime.
To fix the problem an explicit write to clear interrupt register is
required, note that on OSM platforms the register may not be present.
Fixes: 275157b367f4 ("cpufreq: qcom-cpufreq-hw: Add dcvs interrupt support") Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This code is really spurious.
It always returns an ERR_PTR, even when err is known to be 0 and calls
put_device() after a successful device_register() call.
It is likely that the return statement in the normal path is missing.
Add 'return rdev;' to fix it.
Fixes: d787dcdb9c8f ("bus: sunxi-rsb: Add driver for Allwinner Reduced Serial Bus") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Samuel Holland <samuel@sholland.org> Tested-by: Samuel Holland <samuel@sholland.org> Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com> Link: https://lore.kernel.org/r/ef2b9576350bba4c8e05e669e9535e9e2a415763.1650551719.git.christophe.jaillet@wanadoo.fr Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Fixes: 5b0b9e4c2c89 ("tcp: md5: incorrect tcp_header_len for incoming connections") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Francesco Ruggeri <fruggeri@arista.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
I had this bug sitting for too long in my pile, it is time to fix it.
Thanks to Doug Porter for reminding me of it!
We had various attempts in the past, including commit 0cbe6a8f089e ("tcp: remove SOCK_QUEUE_SHRUNK"),
but the issue is that TCP stack currently only generates
EPOLLOUT from input path, when tp->snd_una has advanced
and skb(s) cleaned from rtx queue.
If a flow has a big RTT, and/or receives SACKs, it is possible
that the notsent part (tp->write_seq - tp->snd_nxt) reaches 0
and no more data can be sent until tp->snd_una finally advances.
What is needed is to also check if POLLOUT needs to be generated
whenever tp->snd_nxt is advanced, from output path.
This bug triggers more often after an idle period, as
we do not receive ACK for at least one RTT. tcp_notsent_lowat
could be a fraction of what CWND and pacing rate would allow to
send during this RTT.
In a followup patch, I will remove the bogus call
to tcp_chrono_stop(sk, TCP_CHRONO_SNDBUF_LIMITED)
from tcp_check_space(). Fact that we have decided to generate
an EPOLLOUT does not mean the application has immediately
refilled the transmit queue. This optimistic call
might have been the reason the bug seemed not too serious.
Tested:
200 ms rtt, 1% packet loss, 32 MB tcp_rmem[2] and tcp_wmem[2]
$ echo 500000 >/proc/sys/net/ipv4/tcp_notsent_lowat
$ cat bench_rr.sh
SUM=0
for i in {1..10}
do
V=`netperf -H remote_host -l30 -t TCP_RR -- -r 10000000,10000 -o LOCAL_BYTES_SENT | egrep -v "MIGRATED|Bytes"`
echo $V
SUM=$(($SUM + $V))
done
echo SUM=$SUM
As pointed out by Jakub Kicinski, currently using TUNNEL_SEQ in
collect_md mode is racy for [IP6]GRE[TAP] devices. Consider the
following sequence of events:
1. An [IP6]GRE[TAP] device is created in collect_md mode using "ip link
add ... external". "ip" ignores "[o]seq" if "external" is specified,
so TUNNEL_SEQ is off, and the device is marked as NETIF_F_LLTX (i.e.
it uses lockless TX);
2. Someone sets TUNNEL_SEQ on outgoing skb's, using e.g.
bpf_skb_set_tunnel_key() in an eBPF program attached to this device;
3. gre_fb_xmit() or __gre6_xmit() processes these skb's:
Since we are not using the TX lock (&txq->_xmit_lock), multiple CPUs may
try to do this tunnel->o_seqno++ in parallel, which is racy. Fix it by
making o_seqno atomic_t.
As mentioned by Eric Dumazet in commit b790e01aee74 ("ip_gre: lockless
xmit"), making o_seqno atomic_t increases "chance for packets being out
of order at receiver" when NETIF_F_LLTX is on.
Maybe a better fix would be:
1. Do not ignore "oseq" in external mode. Users MUST specify "oseq" if
they want the kernel to allow sequencing of outgoing packets;
2. Reject all outgoing TUNNEL_SEQ packets if the device was not created
with "oseq".
Unfortunately, that would break userspace.
We could now make [IP6]GRE[TAP] devices always NETIF_F_LLTX, but let us
do it in separate patches to keep this fix minimal.
Suggested-by: Jakub Kicinski <kuba@kernel.org> Fixes: 77a5196a804e ("gre: add sequence number for collect md mode.") Signed-off-by: Peilin Ye <peilin.ye@bytedance.com> Acked-by: William Tu <u9012063@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
For IP6GRE and IP6GRETAP devices, currently o_seqno starts from 1 in
native mode. According to RFC 2890 2.2., "The first datagram is sent
with a sequence number of 0." Fix it.
It is worth mentioning that o_seqno already starts from 0 in collect_md
mode, see the "if (tunnel->parms.collect_md)" clause in __gre6_xmit(),
where tunnel->o_seqno is passed to gre_build_header() before getting
incremented.
Fixes: c12b395a4664 ("gre: Support GRE over IPv6") Signed-off-by: Peilin Ye <peilin.ye@bytedance.com> Acked-by: William Tu <u9012063@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
For GRE and GRETAP devices, currently o_seqno starts from 1 in native
mode. According to RFC 2890 2.2., "The first datagram is sent with a
sequence number of 0." Fix it.
It is worth mentioning that o_seqno already starts from 0 in collect_md
mode, see gre_fb_xmit(), where tunnel->o_seqno is passed to
gre_build_header() before getting incremented.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Peilin Ye <peilin.ye@bytedance.com> Acked-by: William Tu <u9012063@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In the current implementation, when TCP initiates a connection
to an unavailable [ip,port], ECONNREFUSED will be stored in the
TCP socket, but SMC will not. However, some apps (like curl) use
getsockopt(,,SO_ERROR,,) to get the error information, which makes
them miss the error message and behave strangely.
Fixes: 50717a37db03 ("net/smc: nonblocking connect rework") Signed-off-by: liuyacan <liuyacan@corp.netease.com> Reviewed-by: Tony Lu <tonylu@linux.alibaba.com> Acked-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Currently, there are some querying mailboxes sent from VF to PF,
and VF will wait the PF's handling result. For mailbox
HCLGE_MBX_GET_QID_IN_PF and HCLGE_MBX_GET_RSS_KEY, it may fail
when the input parameter is invalid, but the prototype of their
handler function is void. In this case, PF always return success
to VF, which may cause the VF get incorrect result.
Fixes it by adding return value for these function.
Fixes: 63b1279d9905 ("net: hns3: check queue id range before using") Fixes: 532cfc0df1e4 ("net: hns3: add a check for index in hclge_get_rss_key()") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Add validity check for message data length in function
hclge_send_mbx_msg(), avoid unexpected overflow.
Fixes: dde1a86e93ca ("net: hns3: Add mailbox support to PF driver") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Currently, function hclge_get_ring_chain_from_mbx will return -ENOMEM if
ring_num is bigger than HCLGE_MBX_MAX_RING_CHAIN_PARAM_NUM. It is better to
return -EINVAL for the invalid parameter case.
So this patch fixes it by return -EINVAL in this abnormal branch.
Fixes: 5d02a58dae60 ("net: hns3: fix for buffer overflow smatch warning") Signed-off-by: Jie Wang <wangjie125@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If failed to register netdev, it needs to clear INITED state and stop
client in case of cause problem when concurrency with uninitialized
process of driver.
Fixes: a289a7e5c1d4 ("net: hns3: put off calling register_netdev() until client initialize complete") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
if sun50i_cpufreq_get_efuse failed, then opp_tables leak.
Fixes: f328584f7bff ("cpufreq: Add sun50i nvmem based CPU scaling driver") Signed-off-by: Xiaobing Luo <luoxiaobing0926@gmail.com> Reviewed-by: Samuel Holland <samuel@sholland.org> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The correct spelling for the property is gpios. Otherwise, the regulator
will neither reserve nor control any GPIOs. Thus, any SD/MMC card which
can use UHS-I modes will fail.
A null pointer reference issue can be triggered when the response of a
stream reconf request arrives after the timer is triggered, such as:
send Incoming SSN Reset Request --->
CPU0:
reconf timer is triggered,
go to the handler code before hold sk lock
<--- reply with Outgoing SSN Reset Request
CPU1:
process Outgoing SSN Reset Request,
and set asoc->strreset_chunk to NULL
CPU0:
continue the handler code, hold sk lock,
and try to hold asoc->strreset_chunk, crash!
When we try to transmit an skb with md_dst attached through wireguard
we hit a null pointer dereference in wg_xmit() due to the use of
dst_mtu() which calls into dst_blackhole_mtu() which in turn tries to
dereference dst->dev.
Since wireguard doesn't use md_dsts we should use skb_valid_dst(), which
checks for DST_METADATA flag, and if it's set, then falls back to
wireguard's device mtu. That gives us the best chance of transmitting
the packet; otherwise if the blackhole netdev is used we'd get
ETH_MIN_MTU.
If an ACK (s)acks multiple skbs, we favor the information
from the most recently sent skb by choosing the skb with
the highest prior_delivered count. But in the interval
between receiving ACKs, we send multiple skbs with the same
prior_delivered, because the tp->delivered only changes
when we receive an ACK.
We used RACK's solution, copying tcp_rack_sent_after() as
tcp_skb_sent_after() helper to determine "which packet was
sent last?". Later, we will use tcp_skb_sent_after() instead
in RACK.
Fixes: b9f64820fb22 ("tcp: track data delivery rate for a TCP connection") Signed-off-by: Pengcheng Yang <yangpc@wangsu.com> Cc: Paolo Abeni <pabeni@redhat.com> Acked-by: Neal Cardwell <ncardwell@google.com> Tested-by: Neal Cardwell <ncardwell@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/1650422081-22153-1-git-send-email-yangpc@wangsu.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The current EOI handler for LEVEL triggered interrupts calls clk_enable(),
register IO, clk_disable(). The clock manipulation requires locking which
happens with IRQs disabled in clk_enable_lock(). Instead of turning the
clock on and off all the time, enable the clock in case LEVEL interrupt is
requested and keep the clock enabled until all LEVEL interrupts are freed.
The LEVEL interrupts are an exception on this platform and seldom used, so
this does not affect the common case.
This simplifies the LEVEL interrupt handling considerably and also fixes
the following splat found when using preempt-rt:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at kernel/locking/rtmutex.c:2040 __rt_mutex_trylock+0x37/0x62
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.10.109-rt65-stable-standard-00068-g6a5afc4b1217 #85
Hardware name: STM32 (Device Tree Support)
[<c010a45d>] (unwind_backtrace) from [<c010766f>] (show_stack+0xb/0xc)
[<c010766f>] (show_stack) from [<c06353ab>] (dump_stack+0x6f/0x84)
[<c06353ab>] (dump_stack) from [<c01145e3>] (__warn+0x7f/0xa4)
[<c01145e3>] (__warn) from [<c063386f>] (warn_slowpath_fmt+0x3b/0x74)
[<c063386f>] (warn_slowpath_fmt) from [<c063b43d>] (__rt_mutex_trylock+0x37/0x62)
[<c063b43d>] (__rt_mutex_trylock) from [<c063c053>] (rt_spin_trylock+0x7/0x16)
[<c063c053>] (rt_spin_trylock) from [<c036a2f3>] (clk_enable_lock+0xb/0x80)
[<c036a2f3>] (clk_enable_lock) from [<c036ba69>] (clk_core_enable_lock+0x9/0x18)
[<c036ba69>] (clk_core_enable_lock) from [<c034e9f3>] (stm32_gpio_get+0x11/0x24)
[<c034e9f3>] (stm32_gpio_get) from [<c034ef43>] (stm32_gpio_irq_trigger+0x1f/0x48)
[<c034ef43>] (stm32_gpio_irq_trigger) from [<c014aa53>] (handle_fasteoi_irq+0x71/0xa8)
[<c014aa53>] (handle_fasteoi_irq) from [<c0147111>] (generic_handle_irq+0x19/0x22)
[<c0147111>] (generic_handle_irq) from [<c014752d>] (__handle_domain_irq+0x55/0x64)
[<c014752d>] (__handle_domain_irq) from [<c0346f13>] (gic_handle_irq+0x53/0x64)
[<c0346f13>] (gic_handle_irq) from [<c0100ba5>] (__irq_svc+0x65/0xc0)
Exception stack(0xc0e01f18 to 0xc0e01f60)
1f00: 0000300c00000000
1f20: 0000300cc010ff010000000000000000c0e00000c0e0771400000001c0e01f78
1f40: c0e0775800000000ef7cd0ffc0e01f68c010554bc010554240000033ffffffff
[<c0100ba5>] (__irq_svc) from [<c0105542>] (arch_cpu_idle+0xc/0x1e)
[<c0105542>] (arch_cpu_idle) from [<c063be95>] (default_idle_call+0x21/0x3c)
[<c063be95>] (default_idle_call) from [<c01324f7>] (do_idle+0xe3/0x1e4)
[<c01324f7>] (do_idle) from [<c01327b3>] (cpu_startup_entry+0x13/0x14)
[<c01327b3>] (cpu_startup_entry) from [<c0a00c13>] (start_kernel+0x397/0x3d4)
[<c0a00c13>] (start_kernel) from [<00000000>] (0x0)
---[ end trace 0000000000000002 ]---
Power consumption measured on STM32MP157C DHCOM SoM is not increased or
is below noise threshold.
Fixes: 47beed513a85b ("pinctrl: stm32: Add level interrupt support to gpio irq chip") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: Fabien Dessenne <fabien.dessenne@foss.st.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Marc Zyngier <maz@kernel.org> Cc: linux-stm32@st-md-mailman.stormreply.com Cc: linux-arm-kernel@lists.infradead.org
To: linux-gpio@vger.kernel.org Reviewed-by: Fabien Dessenne <fabien.dessenne@foss.st.com> Link: https://lore.kernel.org/r/20220421140827.214088-1-marex@denx.de Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In tcp_create_openreq_child we adjust tcp_header_len for md5 using the
remote address in newsk. But that address is still 0 in newsk at this
point, and it is only set later by the callers (tcp_v[46]_syn_recv_sock).
Use the address from the request socket instead.
Fixes: cfb6eeb4c860 ("[TCP]: MD5 Signature Option (RFC2385) support.") Signed-off-by: Francesco Ruggeri <fruggeri@arista.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20220421005026.686A45EC01F2@us226.sjc.aristanetworks.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
xmit_check_hhlen() observes the dst for getting the device hard header
length to make sure a modified packet can fit. When a helper which changes
the dst - such as bpf_skb_set_tunnel_key() - is called as part of the
xmit program the accessed dst is no longer valid.
Extend d2df92e98a34 ("netfilter: nft_set_rbtree: handle element
re-addition after deletion") to deal with elements with same end flags
in the same transation.
Reset the overlap flag as described by 7c84d41416d8 ("netfilter:
nft_set_rbtree: Detect partial overlaps on insertion").
Fixes: 7c84d41416d8 ("netfilter: nft_set_rbtree: Detect partial overlaps on insertion") Fixes: d2df92e98a34 ("netfilter: nft_set_rbtree: handle element re-addition after deletion") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Reviewed-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The device_node pointer is returned by of_parse_phandle() with refcount
incremented. We should use of_node_put() on it when done.
of_node_put() will check for NULL value.
Fixes: a20f997010c4 ("net: dsa: Don't instantiate phylink for CPU/DSA ports unless needed") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
rpc-if-hyperflash rpc-if-hyperflash: probing of hyperbus device failed
In HyperFlash or Octal-SPI Flash mode, the Transfer Data Enable bits
(SPIDE) in the Manual Mode Enable Setting Register (SMENR) are derived
from half of the transfer size, cfr. the rpcif_bits_set() helper
function. However, rpcif_reg_{read,write}() does not take the bus size
into account, and does not double all Manual Mode Data Register access
sizes when communicating with a HyperFlash or Octal-SPI Flash device.
Fix this, and avoid the back-and-forth conversion between transfer size
and Transfer Data Enable bits, by explicitly storing the transfer size
in struct rpcif, and using that value to determine access size in
rpcif_reg_{read,write}().
Enforce that the "high" Manual Mode Read/Write Data Registers
(SM[RW]DR1) are only used for 8-byte data accesses.
While at it, forbid writing to the Manual Mode Read Data Registers,
as they are read-only.
Fixes: fff53a551db50f5e ("memory: renesas-rpc-if: Correct QSPI data transfer in Manual mode") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Link: https://lore.kernel.org/r/cde9bfacf704c81865f57b15d1b48a4793da4286.1649681476.git.geert+renesas@glider.be Link: https://lore.kernel.org/r/20220420070526.9367-1-krzysztof.kozlowski@linaro.org' Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The stm32_gpio_get() should only be called for LEVEL triggered interrupts,
skip calling it for EDGE triggered interrupts altogether to avoid wasting
CPU cycles in EOI handler. On this platform, EDGE triggered interrupts are
the majority and LEVEL triggered interrupts are the exception no less, and
the CPU cycles are not abundant.
Fixes: 47beed513a85b ("pinctrl: stm32: Add level interrupt support to gpio irq chip") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: Fabien Dessenne <fabien.dessenne@foss.st.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Marc Zyngier <maz@kernel.org> Cc: linux-stm32@st-md-mailman.stormreply.com Cc: linux-arm-kernel@lists.infradead.org
To: linux-gpio@vger.kernel.org Link: https://lore.kernel.org/r/20220415215410.498349-1-marex@denx.de Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Commit 46b5889cc2c5 ("mtd: implement proper partition handling")
started using "mtd_get_master_ofs()" in mtd callbacks to determine
memory offsets by means of 'part' field from mtd_info, what previously
was smashed accessing 'master' field in the mtd_set_dev_defaults() method.
That provides wrong offset what causes hardware access errors.
Just make 'part', 'master' as separate fields, rather than using
union type to avoid 'part' data corruption when mtd_set_dev_defaults()
is called.
wait_for_completion_timeout() returns unsigned long not int.
It returns 0 if timed out, and positive if completed.
The check for <= 0 is ambiguous and should be == 0 here
indicating timeout which is the only error case.
Fixes: 83738d87e3a0 ("mtd: sh_flctl: Add DMA capabilty") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220412083435.29254-1-linmq006@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If EINT_MTK is m and PINCTRL_MTK_V2 is y, build fails:
drivers/pinctrl/mediatek/pinctrl-moore.o: In function `mtk_gpio_set_config':
pinctrl-moore.c:(.text+0xa6c): undefined reference to `mtk_eint_set_debounce'
drivers/pinctrl/mediatek/pinctrl-moore.o: In function `mtk_gpio_to_irq':
pinctrl-moore.c:(.text+0xacc): undefined reference to `mtk_eint_find_irq'
Select EINT_MTK for PINCTRL_MTK_V2 to fix this.
Fixes: 8174a8512e3e ("pinctrl: mediatek: make MediaTek pinctrl v2 driver ready for buidling loadable module") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Link: https://lore.kernel.org/r/20220409105958.37412-1-yuehaibing@huawei.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If clk_prepare_enable() fails we call clk_disable_unprepare()
in the error path what results in a warning that the clock
is disabled and unprepared already.
And if we fail later in phy_g12a_usb3_pcie_probe() then we
bail out w/o calling clk_disable_unprepare().
This patch fixes both errors.
The pinout of the OMAP35 and DM37 variants of the SOM-LV are the
same, but the macros which define the pinmuxing are different
between OMAP3530 and DM3730. The pinmuxing was correct for
for the DM3730, but wrong for the OMAP3530. Since the boot loader
was correctly pin-muxing the pins, this was not obvious. As the
bootloader not guaranteed to pinmux all the pins any more, this
causes an issue, so the pinmux needs to be moved from a common
file to their respective board files.
Fixes: f8a2e3ff7103 ("ARM: dts: Add minimal support for LogicPD OMAP35xx SOM-LV devkit") Signed-off-by: Adam Ford <aford173@gmail.com>
Message-Id: <20220303171818.11060-1-aford173@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The bootloader for the AM3517 has previously done much of the pin
muxing, but as the bootloader is moving more and more to a model
based on the device tree, it may no longer automatically mux the
pins, so it is necessary to add the pinmuxing to the Linux device
trees so the respective peripherals can remain functional.
Fixes: 6ed1d7997561 ("ARM: dts: am3517-evm: Add support for UI board and Audio") Signed-off-by: Adam Ford <aford173@gmail.com>
Message-Id: <20220226214820.747847-1-aford173@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Commit a1ebdb374199 ("ARM: dts: Fix swapped mmc order for omap3")
introduces general mmc aliases. Let's tailor them to the need
of the GTA04 board which does not make use of mmc2 and mmc3 interfaces.
Fixes: a1ebdb374199 ("ARM: dts: Fix swapped mmc order for omap3") Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Message-Id: <dc9173ee3d391d9e92b7ab8ed4f84b29f0a21c83.1646744420.git.hns@goldelico.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Similar to the sc7180 commit, let's drop the IP0 interconnects here
because the IP0 resource is also used in the clk-rpmh driver on sdx55.
It's bad to have the clk framework and interconnect framework control
the same RPMh resource without any coordination. The rpmh driver in the
kernel doesn't aggregate resources between clients either, so leaving
control to clk-rpmh avoids any issues with unused interconnects turning
off IP0 behind the back of the clk framework.
Cc: Alex Elder <elder@linaro.org> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Taniya Das <quic_tdas@quicinc.com> Cc: Mike Tipton <quic_mdtipton@quicinc.com> Fixes: b2150cab9a97 ("clk: qcom: rpmh: add support for SDX55 rpmh IPA clock") Signed-off-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Alex Elder <elder@linaro.org> Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20220412220033.1273607-3-swboyd@chromium.org Signed-off-by: Georgi Djakov <djakov@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The pm_runtime_enable() will increase power disable depth.
If the probe fails, we should use pm_runtime_disable() to balance
pm_runtime_enable().
Add missing pm_runtime_disable() for serdes_am654_probe().
Fixes: 71e2f5c5c224 ("phy: ti: Add a new SERDES driver for TI's AM654x SoC") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Link: https://lore.kernel.org/r/20220301025853.1911-1-linmq006@gmail.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The pm_runtime_enable will increase power disable depth.
If the probe fails, we should use pm_runtime_disable() to balance
pm_runtime_enable(). And use pm_runtime_dont_use_autosuspend() to
undo pm_runtime_use_autosuspend()
In the PM Runtime docs:
Drivers in ->remove() callback should undo the runtime PM changes done
in ->probe(). Usually this means calling pm_runtime_disable(),
pm_runtime_dont_use_autosuspend() etc.
We should do this in error handling.
Fixes: f7f50b2a7b05 ("phy: mapphone-mdm6600: Add runtime PM support for n_gsm on USB suspend") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Link: https://lore.kernel.org/r/20220301024615.31899-1-linmq006@gmail.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Commit bf781869e5cf ("ARM: dts: at91: add pinctrl-{names, 0} for all
gpios") introduces pinctrl phandles for pins used by individual
controllers to avoid failures due to commit 2ab73c6d8323 ("gpio:
Support GPIO controllers without pin-ranges"). For SPI controllers
available on SAMA5D4 and SAMA5D3 some of the pins are defined in
SoC specific dtsi on behalf of pinctrl-0. Adding extra pinctrl phandles
on board specific dts also on behalf of pinctrl-0 overwrite the pinctrl-0
phandle specified in SoC specific dtsi. Thus add the board specific
pinctrl to pinctrl-1.
projects / mirror_ubuntu-jammy-kernel.git / log