While enabling EDAC support for the LS1028A it was discovered that the
memory node has a wrong endianness setting as well as a wrong interrupt
assignment. Fix both.
This was tested on a sl28 board. To force ECC errors, you can use the
error injection supported by the controller in hardware (with
CONFIG_EDAC_DEBUG enabled):
# enable error injection
$ echo 0x100 > /sys/devices/system/edac/mc/mc0/inject_ctrl
# flip lowest bit of the data
$ echo 0x1 > /sys/devices/system/edac/mc/mc0/inject_data_lo
Fixes: 8897f3255c9c ("arm64: dts: Add support for NXP LS1028A SoC") Signed-off-by: Michael Walle <michael@walle.cc> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Add missing exception tracing to XDP when a number of different errors
can occur. The support was only partial. Several errors where not
logged which would confuse the user quite a lot not knowing where and
why the packets disappeared.
Fixes: 74608d17fe29 ("i40e: add support for XDP_TX action") Fixes: 0a714186d3c0 ("i40e: add AF_XDP zero-copy Rx support") Reported-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com> Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Optimize i40e_run_xdp_zc() for the XDP program verdict being
XDP_REDIRECT in the xsk zero-copy path. This path is only used when
having AF_XDP zero-copy on and in that case most packets will be
directed to user space. This provides a little over 100k extra packets
in throughput on my server when running l2fwd in xdpsock.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com> Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
If the hardware is still accessing memory after SMMU translation
is disabled (as part of smmu shutdown callback), then the
IOVAs (I/O virtual address) which it was using will go on the bus
as the physical addresses which will result in unknown crashes
like NoC/interconnect errors.
So, implement shutdown callback for i2c driver to suspend the bus
during system "reboot" or "shutdown".
Fixes: 37692de5d523 ("i2c: i2c-qcom-geni: Add bus driver for the Qualcomm GENI I2C controller") Signed-off-by: Roja Rani Yarubandi <rojay@codeaurora.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Currently in the ice driver, the check whether to
allow a LLDP packet to egress the interface from the
PF_VSI is being based on the SKB's priority field.
It checks to see if the packets priority is equal to
TC_PRIO_CONTROL. Injected LLDP packets do not always
meet this condition.
SCAPY defaults to a sk_buff->protocol value of ETH_P_ALL
(0x0003) and does not set the priority field. There will
be other injection methods (even ones used by end users)
that will not correctly configure the socket so that
SKB fields are correctly populated.
Then ethernet header has to have to correct value for
the protocol though.
Add a check to also allow packets whose ethhdr->h_proto
matches ETH_P_LLDP (0x88CC).
Fixes: 0c3a6101ff2d ("ice: Allow egress control packets from PF_VSI") Signed-off-by: Dave Ertman <david.m.ertman@intel.com> Tested-by: Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Some AVF drivers expect the VF_MBX_ATQLEN register to be cleared for any
type of VFR/VFLR. Fix this by clearing the VF_MBX_ATQLEN register at the
same time as VF_MBX_ARQLEN.
Fixes: 82ba01282cf8 ("ice: clear VF ARQLEN register on reset") Signed-off-by: Brett Creeley <brett.creeley@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Reported by syzbot:
HEAD commit: 90c911ad Merge tag 'fixes' of git://git.kernel.org/pub/scm..
git tree: git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git master link: https://syzkaller.appspot.com/bug?extid=123aa35098fd3c000eb7
compiler: Debian clang version 11.0.1-2
==================================================================
BUG: KASAN: slab-out-of-bounds in fib6_nh_get_excptn_bucket net/ipv6/route.c:1604 [inline]
BUG: KASAN: slab-out-of-bounds in fib6_nh_flush_exceptions+0xbd/0x360 net/ipv6/route.c:1732
Read of size 8 at addr ffff8880145c78f8 by task syz-executor.4/17760
Memory state around the buggy address: ffff8880145c7780: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc ffff8880145c7800: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ffff8880145c7880: 00 00 00 00 fc fc fc fc fc fc fc fc fc fc fc fc
^ ffff8880145c7900: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff8880145c7980: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
==================================================================
In the ip6_route_info_create function, in the case that the nh pointer
is not NULL, the fib6_nh in fib6_info has not been allocated.
Therefore, when trying to free fib6_info in this error case using
fib6_info_release, the function will call fib6_info_destroy_rcu,
which it will access fib6_nh_release(f6i->fib6_nh);
However, f6i->fib6_nh doesn't have any refcount yet given the lack of allocation
causing the reported memory issue above.
Therefore, releasing the empty pointer directly instead would be the solution.
Fixes: f88d8ea67fbdb ("ipv6: Plumb support for nexthop object in a fib6_info") Fixes: 706ec91916462 ("ipv6: Fix nexthop refcnt leak when creating ipv6 route info") Signed-off-by: Coco Li <lixiaoyan@google.com> Cc: David Ahern <dsahern@kernel.org> Reviewed-by: Eric Dumazet <edumazet@google.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Add missing exception tracing to XDP when a number of different
errors can occur. The support was only partial. Several errors
where not logged which would confuse the user quite a lot not
knowing where and why the packets disappeared.
Fixes: 21092e9ce8b1 ("ixgbevf: Add support for XDP_TX action") Reported-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com> Tested-by: Vishakha Jambekar <vishakha.jambekar@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The private helper data size cannot be updated. However, updates that
contain NFCTH_PRIV_DATA_LEN might bogusly hit EBUSY even if the size is
the same.
Add the ct helper extension only for unconfirmed conntrack. Skip rule
evaluation if the ct helper extension does not exist. Thus, you can
only create expectations from the first packet.
It should be possible to remove this limitation by adding a new action
to attach a generic ct helper to the first packet. Then, use this ct
helper extension from follow up packets to create the ct expectation.
While at it, add a missing check to skip the template conntrack too
and remove check for IPCT_UNTRACK which is implicit to !ct.
Fix current behavior of skipping template allocation in case the
ct action is in zone 0.
Skipping the allocation may cause the datapath ct code to ignore the
entire ct action with all its attributes (commit, nat) in case the ct
action in zone 0 was preceded by a ct clear action.
The ct clear action sets the ct_state to untracked and resets the
skb->_nfct pointer. Under these conditions and without an allocated
ct template, the skb->_nfct pointer will remain NULL which will
cause the tc ct action handler to exit without handling commit and nat
actions, if such exist.
For example, the following rule in OVS dp:
recirc_id(0x2),ct_state(+new-est-rel-rpl+trk),ct_label(0/0x1), \
in_port(eth0),actions:ct_clear,ct(commit,nat(src=10.11.0.12)), \
recirc(0x37a)
Will result in act_ct skipping the commit and nat actions in zone 0.
The change removes the skipping of template allocation for zone 0 and
treats it the same as any other zone.
clang doesn't like printing a 32-bit integer using %hX format string:
drivers/hid/i2c-hid/i2c-hid-core.c:994:18: error: format specifies type 'unsigned short' but the argument has type '__u32' (aka 'unsigned int') [-Werror,-Wformat]
client->name, hid->vendor, hid->product);
^~~~~~~~~~~
drivers/hid/i2c-hid/i2c-hid-core.c:994:31: error: format specifies type 'unsigned short' but the argument has type '__u32' (aka 'unsigned int') [-Werror,-Wformat]
client->name, hid->vendor, hid->product);
^~~~~~~~~~~~
Use an explicit cast to truncate it to the low 16 bits instead.
syzbot reported memory leak [1] when adding service with
HASHED flag. We should ignore this flag both from sockopt
and netlink provided data, otherwise the service is not
hashed and not visible while releasing resources.
zap_vma_ptes() is only available when CONFIG_MMU is set/enabled.
Without CONFIG_MMU, vfio_pci.o has build errors, so make
VFIO_PCI depend on MMU.
riscv64-linux-ld: drivers/vfio/pci/vfio_pci.o: in function `vfio_pci_mmap_open':
vfio_pci.c:(.text+0x1ec): undefined reference to `zap_vma_ptes'
riscv64-linux-ld: drivers/vfio/pci/vfio_pci.o: in function `.L0 ':
vfio_pci.c:(.text+0x165c): undefined reference to `zap_vma_ptes'
Fixes: 11c4cd07ba11 ("vfio-pci: Fault mmaps to enable vma tracking") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kernel test robot <lkp@intel.com> Cc: Alex Williamson <alex.williamson@redhat.com> Cc: Cornelia Huck <cohuck@redhat.com> Cc: kvm@vger.kernel.org Cc: Jason Gunthorpe <jgg@nvidia.com> Cc: Eric Auger <eric.auger@redhat.com>
Message-Id: <20210515190856.2130-1-rdunlap@infradead.org> Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
snprintf() should be given the full buffer size, not one less. And it
guarantees nul-termination, so doing it manually afterwards is
pointless.
It's even potentially harmful (though probably not in practice because
CPER_REC_LEN is 256), due to the "return how much would have been
written had the buffer been big enough" semantics. I.e., if the bank
and/or device strings are long enough that the "DIMM location ..."
output gets truncated, writing to msg[n] is a buffer overflow.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Fixes: 3760cd20402d4 ("CPER: Adjust code flow of some functions") Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
UEFI spec 2.9, p.108, table 4-1 lists the scenario that both attributes
are cleared with the description "No memory access protection is
possible for Entry". So we can have valid entries where both attributes
are cleared, so remove the check.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Fixes: 10f0d2f577053 ("efi: Implement generic support for the Memory Attributes table") Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
When support for up to 10 temp sensors and for disabling automatic BIOS
fan control was added, noone updated the index values used for
disallowing fan support and fan type calls.
Fix those values.
Signed-off-by: Armin Wolf <W_Armin@gmx.de> Reviewed-by: Pali Rohár <pali@kernel.org> Link: https://lore.kernel.org/r/20210513154546.12430-1-W_Armin@gmx.de Fixes: 1bb46a20e73b ("hwmon: (dell-smm) Support up to 10 temp sensors") Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
syzbot discovered a bug in which an OOB access was being made because
an unsuitable key_idx value was wrongly considered to be acceptable
while deleting a key in nl80211_del_key().
Since we don't know the cipher at the time of deletion, if
cfg80211_validate_key_settings() were to be called directly in
nl80211_del_key(), even valid keys would be wrongly determined invalid,
and deletion wouldn't occur correctly.
For this reason, a new function - cfg80211_valid_key_idx(), has been
created, to determine if the key_idx value provided is valid or not.
cfg80211_valid_key_idx() is directly called in 2 places -
nl80211_del_key(), and cfg80211_validate_key_settings().
Reported-by: syzbot+49d4cab497c2142ee170@syzkaller.appspotmail.com Tested-by: syzbot+49d4cab497c2142ee170@syzkaller.appspotmail.com Suggested-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com> Link: https://lore.kernel.org/r/20201204215825.129879-1-anant.thazhemadam@gmail.com Cc: stable@vger.kernel.org
[also disallow IGTK key IDs if no IGTK cipher is supported] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Zubin Mithra <zsm@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
sound/usb/mixer_quirks.c: In function ‘snd_microii_controls_create’:
sound/usb/mixer_quirks.c:1694:2: warning: ‘static’ is not at beginning
of declaration [-Wold-style-declaration]
1694 | const static usb_mixer_elem_resume_func_t resume_funcs[] = {
| ^~~~~
RTL8156 sends notifications about every 32ms.
Only display/log notifications when something changes.
This issue has been reported by others:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1832472
https://lkml.org/lkml/2020/8/27/1083
...
[785962.779840] usb 1-1: new high-speed USB device number 5 using xhci_hcd
[785962.929944] usb 1-1: New USB device found, idVendor=0bda, idProduct=8156, bcdDevice=30.00
[785962.929949] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=6
[785962.929952] usb 1-1: Product: USB 10/100/1G/2.5G LAN
[785962.929954] usb 1-1: Manufacturer: Realtek
[785962.929956] usb 1-1: SerialNumber: 000000001
[785962.991755] usbcore: registered new interface driver cdc_ether
[785963.017068] cdc_ncm 1-1:2.0: MAC-Address: 00:24:27:88:08:15
[785963.017072] cdc_ncm 1-1:2.0: setting rx_max = 16384
[785963.017169] cdc_ncm 1-1:2.0: setting tx_max = 16384
[785963.017682] cdc_ncm 1-1:2.0 usb0: register 'cdc_ncm' at usb-0000:00:14.0-1, CDC NCM, 00:24:27:88:08:15
[785963.019211] usbcore: registered new interface driver cdc_ncm
[785963.023856] usbcore: registered new interface driver cdc_wdm
[785963.025461] usbcore: registered new interface driver cdc_mbim
[785963.038824] cdc_ncm 1-1:2.0 enx002427880815: renamed from usb0
[785963.089586] cdc_ncm 1-1:2.0 enx002427880815: network connection: disconnected
[785963.121673] cdc_ncm 1-1:2.0 enx002427880815: network connection: disconnected
[785963.153682] cdc_ncm 1-1:2.0 enx002427880815: network connection: disconnected
...
This is about 2KB per second and will overwrite all contents of a 1MB
dmesg buffer in under 10 minutes rendering them useless for debugging
many kernel problems.
This is also an extra 180 MB/day in /var/logs (or 1GB per week) rendering
the majority of those logs useless too.
The tree checker checks the extent ref hash at read and write time to
make sure we do not corrupt the file system. Generally extent
references go inline, but if we have enough of them we need to make an
item, which looks like
However if key.offset collide with an unrelated extent reference we'll
simply key.offset++ until we get something that doesn't collide.
Obviously this doesn't match at tree checker time, and thus we error
while writing out the transaction. This is relatively easy to
reproduce, simply do something like the following
xfs_io -f -c "pwrite 0 1M" file
offset=2
for i in {0..10000}
do
xfs_io -c "reflink file 0 ${offset}M 1M" file
offset=$(( offset + 2 ))
done
And the sync will error out because we'll abort the transaction. The
magic values above are used because they generate hash collisions with
the first file in the main subvol.
The fix for this is to remove the hash value check from tree checker, as
we have no idea which offset ours should belong to.
Reported-by: Tuomas Lähdekorpi <tuomas.lahdekorpi@gmail.com> Fixes: 0785a9aacf9d ("btrfs: tree-checker: Add EXTENT_DATA_REF check") CC: stable@vger.kernel.org # 5.4+ Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com>
[ add comment] Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Eric Sandeen [Wed, 7 Jul 2021 11:32:08 +0000 (13:32 +0200)]
UBUNTU: SAUCE: seq_file: Disallow extremely large seq buffer allocations
There is no reasonable need for a buffer larger than this,
and it avoids int overflow pitfalls.
Suggested-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Eric Sandeen <sandeen@redhat.com>
CVE-2021-33909 Fixes: 058504edd026 ("fs/seq_file: fallback to vmalloc allocation") Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Acked-by: Juerg Haefliger <juergh@canonical.com> Acked-by: Benjamin M Romer <benjamin.romer@canonical.com>
This has been shown to cause failures with lxd, as the opener process had
different privileges than the writer, preventing lxd to be able to create
new processes inside a container when setting apparmor confinement.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Acked-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Ian May <ian.may@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
UBUNTU: [Packaging]: Add kernel command line condition to hv-kvp-daemon service
linux-cloud-tools-common ships a service for hyper-v hypervisor. It is
known to be prohibited on certain instance types. Add a kernel command
line condition to skip starting this service there.
BugLink: https://bugs.launchpad.net/bugs/1932081 Signed-off-by: Dimitri John Ledkov <dimitri.ledkov@canonical.com>
cc: Marcelo Henrique Cerri <marcelo.cerri@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Andy Whitcroft <andy.whitcroft@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Quinn Tran [Wed, 2 Dec 2020 13:23:06 +0000 (05:23 -0800)]
scsi: qla2xxx: Fix N2N and NVMe connect retry failure
BugLink: https://bugs.launchpad.net/bugs/1860724
FC-NVMe target discovery failed when initiator wwpn < target wwpn in an N2N
(Direct Attach) config, where the driver was stuck on FCP PRLI mode and
failed to retry with NVMe PRLI.
Link: https://lore.kernel.org/r/20201202132312.19966-10-njavali@marvell.com Fixes: 84ed362ac40c ("scsi: qla2xxx: Dual FCP-NVMe target port support”) Fixes: 983f127603fa ("scsi: qla2xxx: Retry PLOGI on FC-NVMe PRLI failure”) Signed-off-by: Quinn Tran <qutran@marvell.com> Signed-off-by: Nilesh Javali <njavali@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 07a5f69248e3486e387c40af64793466371c7d91) Signed-off-by: Nilesh Javali <njavali@marvell.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Guilherme Piccoli <gpiccoli@canonical.com> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1860724
Driver was using a shorter timeout waiting for PLOGI from the peer in
point-to-point configurations. Some devices takes some time (~4 seconds) to
initiate the PLOGI. This peer initiating PLOGI is when the peer has a
higher P-WWN.
Increase the wait time based on N2N R_A_TOV.
Link: https://lore.kernel.org/r/20200929102152.32278-7-njavali@marvell.com Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com> Signed-off-by: Arun Easi <aeasi@marvell.com> Signed-off-by: Nilesh Javali <njavali@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 94eda2717826015a80ca271394c4378747de8936) Signed-off-by: Nilesh Javali <njavali@marvell.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Guilherme Piccoli <gpiccoli@canonical.com> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Quinn Tran [Wed, 26 Feb 2020 22:40:21 +0000 (14:40 -0800)]
scsi: qla2xxx: Set Nport ID for N2N
BugLink: https://bugs.launchpad.net/bugs/1860724
When transitioning from loop to N2N, stale NPort ID is not
re-assigned. Stale ID can collide with remote device. This patch will
re-assign NPort ID on N2N is detected.
Link: https://lore.kernel.org/r/20200226224022.24518-18-hmadhani@marvell.com Signed-off-by: Himanshu Madhani <hmadhani@marvell.com> Signed-off-by: Quinn Tran <qutran@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit ad8a260aa80d4dfa9588fd5d23b71ec922f61c8b) Signed-off-by: Nilesh Javali <njavali@marvell.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Guilherme Piccoli <gpiccoli@canonical.com> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Quinn Tran [Wed, 26 Feb 2020 22:40:18 +0000 (14:40 -0800)]
scsi: qla2xxx: Serialize fc_port alloc in N2N
BugLink: https://bugs.launchpad.net/bugs/1860724
For N2N, fc_port struct is created during report id acquisition. At
later time, the loop resync (fabric, n2n, loop) would trigger the rest
of the login using the created fc_port struct. The loop resync logic
can trigger another fc_port allocation if the 1st allocation was not
able to execute. This patch prevents the 2nd allocation trigger.
Link: https://lore.kernel.org/r/20200226224022.24518-15-hmadhani@marvell.com Signed-off-by: Himanshu Madhani <hmadhani@marvell.com> Signed-off-by: Quinn Tran <qutran@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 11efe8755d73efd153d6459240866b6d52448f19) Signed-off-by: Nilesh Javali <njavali@marvell.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Guilherme Piccoli <gpiccoli@canonical.com> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
(cherry picked from commit 195fb97766da1b41b4d49bccc37e13603bcb49cc) Signed-off-by: Michael Reed <Michael.Reed@canonical.com> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Return the exactly delay time given by root hub descriptor,
this helps to reduce resume time etc.
Due to the root hub descriptor is usually provided by the host
controller driver, if there is compatibility for a root hub,
we can fix it easily without affect other root hub
Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Link: https://lore.kernel.org/r/1618017645-12259-1-git-send-email-chunfeng.yun@mediatek.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
<CPU A, t0>: Executing: __netif_receive_skb() ->__netif_receive_skb_core()
-> arp_rcv() -> arp_process().arp_process() calls __neigh_lookup() which
takes a reference on neighbour entry 'n'.
Moves further along, arp_process() and calls neigh_update()->
__neigh_update(). Neighbour entry is unlocked just before a call to
neigh_update_gc_list.
This unlocking paves way for another thread that may take a reference on
the same and mark it dead and remove it from gc_list.
<CPU B, t1> - neigh_flush_dev() is under execution and calls
neigh_mark_dead(n) marking the neighbour entry 'n' as dead. Also n will be
removed from gc_list.
Moves further along neigh_flush_dev() and calls
neigh_cleanup_and_release(n), but since reference count increased in t1,
'n' couldn't be destroyed.
<CPU A, t3>- Code hits neigh_update_gc_list, with neighbour entry
set as dead.
<CPU A, t4> - arp_process() finally calls neigh_release(n), destroying
the neighbour entry and we have a destroyed ntry still part of gc_list.
Fixes: eb4e8fac00d1("neighbour: Prevent a dead entry from updating gc_list") Signed-off-by: Chinmay Agarwal <chinagar@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Commit 31db0dbd7244 ("net: hso: check for allocation failure in
hso_create_bulk_serial_device()") recently started returning an error
when the driver fails to allocate resources for the interrupt endpoint
and tiocmget functionality.
For consistency let's bail out from probe also if the URB allocation
fails.
Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Currently skb_checksum_help()'s return is ignored, but it may
return error when it fails to allocate memory when linearizing.
So adds checking for the return of skb_checksum_help().
Fixes: 76ad4f0ee747("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC") Fixes: 3db084d28dc0("net: hns3: Fix for vxlan tx checksum bug") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
As part of the W=1 compliation series, these lines all created
warnings about unused variables that were assigned a value. Most
of them are from register reads, but some are just picking up
a return value from a function and never doing anything with it.
Fixed warnings:
.../ethernet/brocade/bna/bnad.c:3280:6: warning: variable ‘rx_count’ set but not used [-Wunused-but-set-variable]
.../ethernet/brocade/bna/bnad.c:3280:6: warning: variable ‘rx_count’ set but not used [-Wunused-but-set-variable]
.../ethernet/cortina/gemini.c:512:6: warning: variable ‘val’ set but not used [-Wunused-but-set-variable]
.../ethernet/cortina/gemini.c:2110:21: warning: variable ‘config0’ set but not used [-Wunused-but-set-variable]
.../ethernet/cavium/liquidio/octeon_device.c:1327:6: warning: variable ‘val32’ set but not used [-Wunused-but-set-variable]
.../ethernet/cavium/liquidio/octeon_device.c:1358:6: warning: variable ‘val32’ set but not used [-Wunused-but-set-variable]
.../ethernet/dec/tulip/media.c:322:8: warning: variable ‘setup’ set but not used [-Wunused-but-set-variable]
.../ethernet/dec/tulip/de4x5.c:4928:13: warning: variable ‘r3’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:4981:6: warning: variable ‘rx_status’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:6510:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:6087: warning: cannot understand function prototype: 'struct hw_regs '
.../ethernet/microchip/lan743x_main.c:161:6: warning: variable ‘int_en’ set but not used [-Wunused-but-set-variable]
.../ethernet/microchip/lan743x_main.c:1702:6: warning: variable ‘int_sts’ set but not used [-Wunused-but-set-variable]
.../ethernet/microchip/lan743x_main.c:3041:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
.../ethernet/natsemi/ns83820.c:603:6: warning: variable ‘tbisr’ set but not used [-Wunused-but-set-variable]
.../ethernet/natsemi/ns83820.c:1207:11: warning: variable ‘tanar’ set but not used [-Wunused-but-set-variable]
.../ethernet/marvell/mvneta.c:754:6: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
.../ethernet/neterion/vxge/vxge-traffic.c:33:6: warning: variable ‘val64’ set but not used [-Wunused-but-set-variable]
.../ethernet/neterion/vxge/vxge-traffic.c:160:6: warning: variable ‘val64’ set but not used [-Wunused-but-set-variable]
.../ethernet/neterion/vxge/vxge-traffic.c:490:6: warning: variable ‘val32’ set but not used [-Wunused-but-set-variable]
.../ethernet/neterion/vxge/vxge-traffic.c:2378:6: warning: variable ‘val64’ set but not used [-Wunused-but-set-variable]
.../ethernet/packetengines/yellowfin.c:1063:18: warning: variable ‘yf_size’ set but not used [-Wunused-but-set-variable]
.../ethernet/realtek/8139cp.c:1242:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
.../ethernet/mellanox/mlx4/en_tx.c:858:6: warning: variable ‘ring_cons’ set but not used [-Wunused-but-set-variable]
.../ethernet/sis/sis900.c:792:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:878:11: warning: variable ‘rx_ev_pkt_type’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:877:23: warning: variable ‘rx_ev_mcast_pkt’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:877:7: warning: variable ‘rx_ev_hdr_type’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:876:7: warning: variable ‘rx_ev_other_err’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:1646:21: warning: variable ‘buftbl_min’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:2535:32: warning: variable ‘spec’ set but not used [-Wunused-but-set-variable]
.../ethernet/via/via-velocity.c:880:6: warning: variable ‘curr_status’ set but not used [-Wunused-but-set-variable]
.../ethernet/ti/tlan.c:656:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
.../ethernet/ti/davinci_emac.c:1230:6: warning: variable ‘num_tx_pkts’ set but not used [-Wunused-but-set-variable]
.../ethernet/synopsys/dwc-xlgmac-common.c:516:8: warning: variable ‘str’ set but not used [-Wunused-but-set-variable]
.../ethernet/ti/cpsw_new.c:1662:22: warning: variable ‘priv’ set but not used [-Wunused-but-set-variable]
The register reads should be OK, because the current
implementation of readl and friends will always execute even
without an lvalue.
When it makes sense, just remove the lvalue assignment and the
local. Other times, just remove the offending code, and
occasionally, just mark the variable as maybe unused since it
could be used in an ifdef or debug scenario.
Only compile tested with W=1.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Acked-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[fixes gcc-11 build warnings - gregkh] Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
i915: fix build warning in intel_dp_get_link_status()
BugLink: https://bugs.launchpad.net/bugs/1931166
There is a build warning using gcc-11 showing a mis-match in the .h and .c
definitions of intel_dp_get_link_status():
CC [M] drivers/gpu/drm/i915/display/intel_dp.o
drivers/gpu/drm/i915/display/intel_dp.c:4139:56: warning: argument 2 of type ‘u8[6]’ {aka ‘unsigned char[6]’} with mismatched bound [-Warray-parameter=]
4139 | intel_dp_get_link_status(struct intel_dp *intel_dp, u8 link_status[DP_LINK_STATUS_SIZE])
| ~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/gpu/drm/i915/display/intel_dp.c:51:
drivers/gpu/drm/i915/display/intel_dp.h:105:57: note: previously declared as ‘u8 *’ {aka ‘unsigned char *’}
105 | intel_dp_get_link_status(struct intel_dp *intel_dp, u8 *link_status);
| ~~~~^~~~~~~~~~~
This was fixed accidentally commit b30edfd8d0b4 ("drm/i915: Switch to LTTPR
non-transparent mode link training") by getting rid of the function entirely,
but that is not a viable backport for a stable kernel, so just fix up the
function definition to remove the build warning entirely. There is no
functional change for this, and it fixes up one of the last 'make allmodconfig'
build warnings when using gcc-11 on this kernel tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
intel_dp_check_mst_status() uses a 14-byte array to read the DPRX Event
Status Indicator data, but then passes that buffer at offset 10 off as
an argument to drm_dp_channel_eq_ok().
End result: there are only 4 bytes remaining of the buffer, yet
drm_dp_channel_eq_ok() wants a 6-byte buffer. gcc-11 correctly warns
about this case:
drivers/gpu/drm/i915/display/intel_dp.c: In function ‘intel_dp_check_mst_status’:
drivers/gpu/drm/i915/display/intel_dp.c:3491:22: warning: ‘drm_dp_channel_eq_ok’ reading 6 bytes from a region of size 4 [-Wstringop-overread]
3491 | !drm_dp_channel_eq_ok(&esi[10], intel_dp->lane_count)) {
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/i915/display/intel_dp.c:3491:22: note: referencing argument 1 of type ‘const u8 *’ {aka ‘const unsigned char *’}
In file included from drivers/gpu/drm/i915/display/intel_dp.c:38:
include/drm/drm_dp_helper.h:1466:6: note: in a call to function ‘drm_dp_channel_eq_ok’
1466 | bool drm_dp_channel_eq_ok(const u8 link_status[DP_LINK_STATUS_SIZE],
| ^~~~~~~~~~~~~~~~~~~~
6:14 elapsed
This commit just extends the original array by 2 zero-initialized bytes,
avoiding the warning.
There may be some underlying bug in here that caused this confusion, but
this is at least no worse than the existing situation that could use
random data off the stack.
Cc: Jani Nikula <jani.nikula@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Dave Airlie <airlied@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
rt2880_wdt.c uses (well, attempts to use) rt_sysc_membase. However,
when this watchdog driver is built as a loadable module, there is a
build error since the rt_sysc_membase symbol is not exported.
Export it to quell the build error.
board-xxs1500.c references 2 functions without declaring them, so add
the header file to placate the build.
../arch/mips/alchemy/board-xxs1500.c: In function 'board_setup':
../arch/mips/alchemy/board-xxs1500.c:56:2: error: implicit declaration of function 'alchemy_gpio1_input_enable' [-Werror=implicit-function-declaration]
56 | alchemy_gpio1_input_enable();
../arch/mips/alchemy/board-xxs1500.c:57:2: error: implicit declaration of function 'alchemy_gpio2_enable'; did you mean 'alchemy_uart_enable'? [-Werror=implicit-function-declaration]
57 | alchemy_gpio2_enable();
Fixes: 8e026910fcd4 ("MIPS: Alchemy: merge GPR/MTX-1/XXS1500 board code into single files") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: linux-mips@vger.kernel.org Cc: Manuel Lauss <manuel.lauss@googlemail.com> Cc: Ralf Baechle <ralf@linux-mips.org> Acked-by: Manuel Lauss <manuel.lauss@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If Qdisc_ops->init() is failed, Qdisc_ops->reset() would be called.
When dsmark_init(Qdisc_ops->init()) is failed, it possibly doesn't
initialize dsmark_qdisc_data->q. But dsmark_reset(Qdisc_ops->reset())
uses dsmark_qdisc_data->q pointer wihtout any null checking.
So, panic would occur.
Test commands:
sysctl net.core.default_qdisc=dsmark -w
ip link add dummy0 type dummy
ip link add vw0 link dummy0 type virt_wifi
ip link set vw0 up
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The MT7628/88 SoC(s) have other (limited) packet counter registers than
currently supported in the mtk_eth_soc driver. This patch adds support
for reading these registers, so that the packet statistics are correctly
updated.
Additionally the defines for the non-MT7628 variant packet counter
registers are added and used in this patch instead of using hard coded
values.
Signed-off-by: Stefan Roese <sr@denx.de> Fixes: 296c9120752b ("net: ethernet: mediatek: Add MT7628/88 SoC support") Cc: Felix Fietkau <nbd@nbd.name> Cc: John Crispin <john@phrozen.org> Cc: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com> Cc: Reto Schneider <code@reto-schneider.ch> Cc: Reto Schneider <reto.schneider@husqvarnagroup.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Commit dbd1759e6a9c ("ipv6: on reassembly, record frag_max_size")
filled the frag_max_size field in IP6CB in the input path.
The field should also be filled in case of atomic fragments.
Fixes: dbd1759e6a9c ('ipv6: on reassembly, record frag_max_size') Signed-off-by: Francesco Ruggeri <fruggeri@arista.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In a situation where memory allocation or dma mapping fails, an
invalid address is programmed into the descriptor. This can lead
to memory corruption. If the memory allocation fails, DMA should
reuse the previous skb and mapping and drop the packet. This patch
also increments rx drop counter.
Fixes: fe1a56420cf2 ("net: lantiq: Add Lantiq / Intel VRX200 Ethernet driver ") Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Check that the MTU value requested by the VF is in the supported
range of MTUs before attempting to set the VF large packet enable,
otherwise reject the request. This also avoids unnecessary
register updates in the case of the 82599 controller.
Fixes: 872844ddb9e4 ("ixgbe: Enable jumbo frames support w/ SR-IOV") Co-developed-by: Piotr Skajewski <piotrx.skajewski@intel.com> Signed-off-by: Piotr Skajewski <piotrx.skajewski@intel.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Co-developed-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The skb_change_head() helper did not set "skb->mac_len", which is
problematic when it's used in combination with skb_redirect_peer().
Without it, redirecting a packet from a L3 device such as wireguard to
the veth peer device will cause skb->data to point to the middle of the
IP header on entry to tcp_v4_rcv() since the L2 header is not pulled
correctly due to mac_len=0.
Fixes: 3a0af8fd61f9 ("bpf: BPF for lightweight tunnel infrastructure") Signed-off-by: Jussi Maki <joamaki@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20210519154743.2554771-2-joamaki@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This error path returns zero (success) but it should return -EINVAL.
Fixes: 3333cb7187b9 ("ASoC: cs35l33: Initial commit of the cs35l33 CODEC driver.") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/YKXuyGEzhPT35R3G@mwanda Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Hardware register having the server TID base can contain
invalid values when adapter is in bad state (for example,
due to AER fatal error). Reading these invalid values in the
register can lead to out-of-bound memory access. So, fix
by using the saved server TID base when clearing filters.
Fixes: b1a79360ee86 ("cxgb4: Delete all hash and TCAM filters before resource cleanup") Signed-off-by: Raju Rangoju <rajur@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
SKBs with skb_get_queue_mapping(skb) == tx_cfg.num_queues should also be
considered invalid.
Fixes: f5cedc84a30d ("gve: Add transmit and receive support") Signed-off-by: David Awogbemila <awogbemila@google.com> Acked-by: Willem de Brujin <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
As currently written, if the driver checks for more work (via
gve_tx_poll or gve_rx_poll) before the device posts work and the
irq doorbell is not unmasked
(via iowrite32be(GVE_IRQ_ACK | GVE_IRQ_EVENT, ...)) before the device
attempts to raise an interrupt, an interrupt is lost and this could
potentially lead to the traffic being completely halted. For
example, if a tx queue has already been stopped, the driver won't get
the chance to complete work and egress will be halted.
We need a full memory barrier in the poll
routine to ensure that the irq doorbell is unmasked before the driver
checks for more work.
Fixes: f5cedc84a30d ("gve: Add transmit and receive support") Signed-off-by: Catherine Sullivan <csully@google.com> Signed-off-by: David Awogbemila <awogbemila@google.com> Acked-by: Willem de Brujin <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When freeing notification blocks, we index priv->msix_vectors.
If we failed to allocate priv->msix_vectors (see abort_with_msix_vectors)
this could lead to a NULL pointer dereference if the driver is unloaded.
Fixes: 893ce44df565 ("gve: Add basic driver framework for Compute Engine Virtual NIC") Signed-off-by: David Awogbemila <awogbemila@google.com> Acked-by: Willem de Brujin <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If we do not get the expected number of vectors from
pci_enable_msix_range, we update priv->num_ntfy_blks but not
priv->mgmt_msix_idx. This patch fixes this so that priv->mgmt_msix_idx
is updated accordingly.
Fixes: f5cedc84a30d ("gve: Add transmit and receive support") Signed-off-by: David Awogbemila <awogbemila@google.com> Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Correctly check the TX QPL was assigned and unassigned if
other steps in the allocation fail.
Fixes: f5cedc84a30d (gve: Add transmit and receive support) Signed-off-by: Catherine Sullivan <csully@google.com> Signed-off-by: David Awogbemila <awogbemila@google.com> Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
mld_newpack() doesn't allow to allocate high order page,
only order-0 allocation is allowed.
If headroom size is too large, a kernel panic could occur in skb_put().
Test commands:
ip netns del A
ip netns del B
ip netns add A
ip netns add B
ip link add veth0 type veth peer name veth1
ip link set veth0 netns A
ip link set veth1 netns B
ip netns exec A ip link set lo up
ip netns exec A ip link set veth0 up
ip netns exec A ip -6 a a 2001:db8:0::1/64 dev veth0
ip netns exec B ip link set lo up
ip netns exec B ip link set veth1 up
ip netns exec B ip -6 a a 2001:db8:0::2/64 dev veth1
for i in {1..99}
do
let A=$i-1
ip netns exec A ip link add ip6gre$i type ip6gre \
local 2001:db8:$A::1 remote 2001:db8:$A::2 encaplimit 100
ip netns exec A ip -6 a a 2001:db8:$i::1/64 dev ip6gre$i
ip netns exec A ip link set ip6gre$i up
ip netns exec B ip link add ip6gre$i type ip6gre \
local 2001:db8:$A::2 remote 2001:db8:$A::1 encaplimit 100
ip netns exec B ip -6 a a 2001:db8:$i::2/64 dev ip6gre$i
ip netns exec B ip link set ip6gre$i up
done
Allowing high order page allocation could fix this problem.
Fixes: 72e09ad107e7 ("ipv6: avoid high order allocations") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Otherwise, some of the recently added HyperV VF IDs would not be
recognized as VF devices and they would not initialize properly.
Fixes: 7fbf359bb2c1 ("bnxt_en: Add PCI IDs for Hyper-V VF devices.") Reviewed-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Andy Gospodarek <gospo@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Fix to return -EPERM from the error handling case instead of 0, as done
elsewhere in this function.
Fixes: b6016b767397 ("[BNX2]: New Broadcom gigabit network driver.") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> Reviewed-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In current kernels, small allocations never actually fail so this
patch shouldn't affect runtime.
Originally this error handling code written with the idea that if
the "serial->tiocmget" allocation failed, then we would continue
operating instead of bailing out early. But in later years we added
an unchecked dereference on the next line.
Since these allocations are never going fail in real life, this is
mostly a philosophical debate, but I think bailing out early is the
correct behavior that the user would want. And generally it's safer to
bail as soon an error happens.
Fixes: af0de1303c4e ("usb: hso: obey DMA rules in tiocmget") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Johan Hovold <johan@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The netdev qeueue might be stopped when byte queue limit has
reached or tx hw ring is full, net_tx_action() may still be
rescheduled if STATE_MISSED is set, which consumes unnecessary
cpu without dequeuing and transmiting any skb because the
netdev queue is stopped, see qdisc_run_end().
This patch fixes it by checking the netdev queue state before
calling qdisc_run() and clearing STATE_MISSED if netdev queue is
stopped during qdisc_run(), the net_tx_action() is rescheduled
again when netdev qeueue is restarted, see netif_tx_wake_queue().
As there is time window between netif_xmit_frozen_or_stopped()
checking and STATE_MISSED clearing, between which STATE_MISSED
may set by net_tx_action() scheduled by netif_tx_wake_queue(),
so set the STATE_MISSED again if netdev queue is restarted.
Fixes: 6b3ba9146fe6 ("net: sched: allow qdiscs to handle locking") Reported-by: Michal Kubecek <mkubecek@suse.cz> Acked-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Currently qdisc_run() checks the STATE_DEACTIVATED of lockless
qdisc before calling __qdisc_run(), which ultimately clear the
STATE_MISSED when all the skb is dequeued. If STATE_DEACTIVATED
is set before clearing STATE_MISSED, there may be rescheduling
of net_tx_action() at the end of qdisc_run_end(), see below:
__qdisc_run() is not called by net_tx_atcion() in CPU0 because
CPU2 has set STATE_DEACTIVATED flag during dev_deactivate(), and
STATE_MISSED is only cleared in __qdisc_run(), __netif_schedule
is called at the end of qdisc_run_end(), causing tx action
rescheduling problem.
qdisc_run() called by net_tx_action() runs in the softirq context,
which should has the same semantic as the qdisc_run() called by
__dev_xmit_skb() protected by rcu_read_lock_bh(). And there is a
synchronize_net() between STATE_DEACTIVATED flag being set and
qdisc_reset()/some_qdisc_is_busy in dev_deactivate(), we can safely
bail out for the deactived lockless qdisc in net_tx_action(), and
qdisc_reset() will reset all skb not dequeued yet.
So add the rcu_read_lock() explicitly to protect the qdisc_run()
and do the STATE_DEACTIVATED checking in net_tx_action() before
calling qdisc_run_begin(). Another option is to do the checking in
the qdisc_run_end(), but it will add unnecessary overhead for
non-tx_action case, because __dev_queue_xmit() will not see qdisc
with STATE_DEACTIVATED after synchronize_net(), the qdisc with
STATE_DEACTIVATED can only be seen by net_tx_action() because of
__netif_schedule().
The STATE_DEACTIVATED checking in qdisc_run() is to avoid race
between net_tx_action() and qdisc_reset(), see:
commit d518d2ed8640 ("net/sched: fix race between deactivation
and dequeue for NOLOCK qdisc"). As the bailout added above for
deactived lockless qdisc in net_tx_action() provides better
protection for the race without calling qdisc_run() at all, so
remove the STATE_DEACTIVATED checking in qdisc_run().
After qdisc_reset(), there is no skb in qdisc to be dequeued, so
clear the STATE_MISSED in dev_reset_queue() too.
Fixes: 6b3ba9146fe6 ("net: sched: allow qdiscs to handle locking") Acked-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
V8: Clearing STATE_MISSED before calling __netif_schedule() has
avoid the endless rescheduling problem, but there may still
be a unnecessary rescheduling, so adjust the commit log. Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
cpu1 enqueue a skb without calling __qdisc_run() because cpu0
has not released the lock yet and spin_trylock() return false
for cpu1 in qdisc_run_begin(), and cpu0 do not see the skb
enqueued by cpu1 when calling dequeue_skb() because cpu1 may
enqueue the skb after cpu0 calling dequeue_skb() and before
cpu0 calling qdisc_run_end().
Lockless qdisc has below another concurrent problem when
tx_action is involved:
This patch fixes the above data race by:
1. If the first spin_trylock() return false and STATE_MISSED is
not set, set STATE_MISSED and retry another spin_trylock() in
case other CPU may not see STATE_MISSED after it releases the
lock.
2. reschedule if STATE_MISSED is set after the lock is released
at the end of qdisc_run_end().
For tx_action case, STATE_MISSED is also set when cpu1 is at the
end if qdisc_run_end(), so tx_action will be rescheduled again
to dequeue the skb enqueued by cpu2.
Clear STATE_MISSED before retrying a dequeuing when dequeuing
returns NULL in order to reduce the overhead of the second
spin_trylock() and __netif_schedule() calling.
Also clear the STATE_MISSED before calling __netif_schedule()
at the end of qdisc_run_end() to avoid doing another round of
dequeuing in the pfifo_fast_dequeue().
The performance impact of this patch, tested using pktgen and
dummy netdev with pfifo_fast qdisc attached:
Fixes: 6b3ba9146fe6 ("net: sched: allow qdiscs to handle locking") Acked-by: Jakub Kicinski <kuba@kernel.org> Tested-by: Juergen Gross <jgross@suse.com> Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In tls_sw_splice_read, checkout MSG_* is inappropriate, should use
SPLICE_*, update tls_wait_data to accept nonblock arguments instead
of flags for recvmsg and splice.
Fixes: c46234ebb4d1 ("tls: RX path for ktls") Signed-off-by: Jim Ma <majinjing3@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
We have observed meters working unexpected if traffic is 3+Gbit/s
with multiple connections.
now_ms is not pretected by meter->lock, we may get a negative
long_delta_ms when another cpu updated meter->used, then:
delta_ms = (u32)long_delta_ms;
which will be a large value.
band->bucket += delta_ms * band->rate;
then we get a wrong band->bucket.
OpenVswitch userspace datapath has fixed the same issue[1] some
time ago, and we port the implementation to kernel datapath.
Fixes: 96fbc13d7e77 ("openvswitch: Add meter infrastructure") Signed-off-by: Tao Liu <thomas.liu@ucloud.cn> Suggested-by: Ilya Maximets <i.maximets@ovn.org> Reviewed-by: Ilya Maximets <i.maximets@ovn.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
'bus->mii_bus' has been allocated with 'devm_mdiobus_alloc_size()' in the
probe function. So it must not be freed explicitly or there will be a
double free.
Remove the incorrect 'mdiobus_free' in the error handling path of the
probe function and in remove function.
Suggested-By: Andrew Lunn <andrew@lunn.ch> Fixes: 35d2aeac9810 ("phy: mdio-octeon: Use devm_mdiobus_alloc_size()") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
'bus->mii_bus' have been allocated with 'devm_mdiobus_alloc_size()' in the
probe function. So it must not be freed explicitly or there will be a
double free.
Remove the incorrect 'mdiobus_free' in the remove function.
Fixes: 379d7ac7ca31 ("phy: mdio-thunder: Add driver for Cavium Thunder SoC MDIO buses.") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If the memory allocated for cbd_base is failed, it should
free the memory allocated for the queues, otherwise it causes
memory leak.
And if the memory allocated for the queues is failed, it can
return error directly.
Fixes: 59d0f7465644 ("net: fec: init multi queue date structure") Signed-off-by: Fugang Duan <fugang.duan@nxp.com> Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If the owing socket is shutting down - e.g. the sock reference
count already dropped to 0 and only sk_wmem_alloc is keeping
the sock alive, skb_orphan_partial() becomes a no-op.
When forwarding packets over veth with GRO enabled, the above
causes refcount errors.
This change addresses the issue with a plain skb_orphan() call
in the critical scenario.
Fixes: 9adc89af724f ("net: let skb_orphan_partial wake-up waiters.") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
We have a really nice flag in the channel_program struct that
indicates if it had been initialized by cp_init(), and use it
as a guard in the other cp accessor routines, but not for a
duplicate call into cp_init(). The possibility of this occurring
is low, because that flow is protected by the private->io_mutex
and FSM CP_PROCESSING state. But then why bother checking it
in (for example) cp_prefetch() then?
Let's just be consistent and check for that in cp_init() too.
Fixes: 71189f263f8a3 ("vfio-ccw: make it safe to access channel programs") Signed-off-by: Eric Farman <farman@linux.ibm.com> Reviewed-by: Cornelia Huck <cohuck@redhat.com> Acked-by: Matthew Rosato <mjrosato@linux.ibm.com>
Message-Id: <20210511195631.3995081-2-farman@linux.ibm.com> Signed-off-by: Cornelia Huck <cohuck@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
cs42l42 does not support standard burst transfers so the use_single_read
and use_single_write flags must be set in the regmap config.
Because of this bug, the patch:
commit 0a0eb567e1d4 ("ASoC: cs42l42: Minor error paths fixups")
broke cs42l42 probe() because without the use_single_* flags it causes
regmap to issue a burst read.
However, the missing use_single_* could cause problems anyway because the
regmap cache can attempt burst transfers if these flags are not set.
Fixes: 2c394ca79604 ("ASoC: Add support for CS42L42 codec") Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com> Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/20210511132855.27159-1-rf@opensource.cirrus.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
DSA implements a bunch of 'standardized' ethtool statistics counters,
namely tx_packets, tx_bytes, rx_packets, rx_bytes. So whatever the
hardware driver returns in .get_sset_count(), we need to add 4 to that.
That is ok, except that .get_sset_count() can return a negative error
code, for example:
-EIO is -5, and with 4 added to it, it becomes -1, aka -EPERM. One can
imagine that certain error codes may even become positive, although
based on code inspection I did not see instances of that.
Check the error code first, if it is negative return it as-is.
Based on a similar patch for dsa_master_get_strings from Dan Carpenter:
https://patchwork.kernel.org/project/netdevbpf/patch/YJaSe3RPgn7gKxZv@mwanda/
Fixes: 91da11f870f0 ("net: Distributed Switch Architecture protocol support") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: xinhui pan <xinhui.pan@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
projects / mirror_ubuntu-focal-kernel.git / log