Olof Johansson [Wed, 24 Feb 2016 08:05:11 +0000 (00:05 -0800)]
Merge tag 'omap-for-v4.5/fixes-rc3-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Few fixes for omaps against v4.5-rc3:
- Improve omap_device error message to tell driver writers what is
wrong after commit 5de85b9d57ab ("PM / runtime: Re-init runtime PM
states at probe error and driver unbind"). There will be also a
handful of driver related fixes also queued separately. But adding
this error message makes it easy to fix any omap_device using
drivers suffering from this issue so I think it's important to
have.
- Also related to commit 5de85b9d57ab discussion, let's fix a bug
where disabling PM runtime via sysfs will also cause the hardware
state to be different from PM runtime state.
- Fix audio clocks for beagle-x15.
- Use wakeup-source instead of gpio-key,wakeup for the new entries
that sneaked in during the merge window.
- Fix a legacy booting vs device tree based booting regression for
n900 where the legacy user space expects to have the device
revision available in /proc/atags also when booted with device
tree.
* tag 'omap-for-v4.5/fixes-rc3-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix omap_device for module reload on PM runtime forbid
ARM: OMAP2+: Improve omap_device error for driver writers
ARM: DTS: am57xx-beagle-x15: Select SYS_CLK2 for audio clocks
ARM: dts: am335x/am57xx: replace gpio-key,wakeup with wakeup-source property
ARM: OMAP2+: Set system_rev from ATAGS for n900
Olof Johansson [Wed, 24 Feb 2016 07:59:29 +0000 (23:59 -0800)]
Merge tag 'mvebu-fixes-4.5-2' of git://git.infradead.org/linux-mvebu into fixes
mvebu fixes for 4.5 (part 2)
- Fix the missing mtd flash on linkstation lswtgl
- Use unique machine name for the kirkwood ds112 (for Debian flash-kernel tool)
* tag 'mvebu-fixes-4.5-2' of git://git.infradead.org/linux-mvebu:
ARM: dts: orion5x: fix the missing mtd flash on linkstation lswtgl
ARM: dts: kirkwood: use unique machine name for ds112
Linus Torvalds [Sat, 20 Feb 2016 17:32:40 +0000 (09:32 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"This is unusually large, partly due to the EFI fixes that prevent
accidental deletion of EFI variables through efivarfs that may brick
machines. These fixes are somewhat involved to maintain compatibility
with existing install methods and other usage modes, while trying to
turn off the 'rm -rf' bricking vector.
Other fixes are for large page ioremap()s and for non-temporal
user-memcpy()s"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Fix vmalloc_fault() to handle large pages properly
hpet: Drop stale URLs
x86/uaccess/64: Handle the caching of 4-byte nocache copies properly in __copy_user_nocache()
x86/uaccess/64: Make the __copy_user_nocache() assembly code more readable
lib/ucs2_string: Correct ucs2 -> utf8 conversion
efi: Add pstore variables to the deletion whitelist
efi: Make efivarfs entries immutable by default
efi: Make our variable validation list include the guid
efi: Do variable name validation tests in utf8
efi: Use ucs2_as_utf8 in efivarfs instead of open coding a bad version
lib/ucs2_string: Add ucs2 -> utf8 helper functions
Linus Torvalds [Sat, 20 Feb 2016 17:30:42 +0000 (09:30 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"A handful of CPU hotplug related fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Plug potential memory leak in CPU_UP_PREPARE
perf/core: Remove the bogus and dangerous CPU_DOWN_FAILED hotplug state
perf/core: Remove bogus UP_CANCELED hotplug state
perf/x86/amd/uncore: Plug reference leak
Linus Torvalds [Sat, 20 Feb 2016 17:22:11 +0000 (09:22 -0800)]
Merge tag 'powerpc-4.5-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix build error on 32-bit with checkpoint restart from Aneesh Kumar
- Fix dedotify for binutils >= 2.26 from Andreas Schwab
- Don't trace hcalls on offline CPUs from Denis Kirjanov
- eeh: Fix stale cached primary bus from Gavin Shan
- eeh: Fix stale PE primary bus from Gavin Shan
- mm: Fix Multi hit ERAT cause by recent THP update from Aneesh Kumar K.V
- ioda: Set "read" permission when "write" is set from Alexey Kardashevskiy
* tag 'powerpc-4.5-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/ioda: Set "read" permission when "write" is set
powerpc/mm: Fix Multi hit ERAT cause by recent THP update
powerpc/powernv: Fix stale PE primary bus
powerpc/eeh: Fix stale cached primary bus
powerpc/pseries: Don't trace hcalls on offline CPUs
powerpc: Fix dedotify for binutils >= 2.26
powerpc/book3s_32: Fix build error with checkpoint restart
Linus Torvalds [Sat, 20 Feb 2016 17:19:56 +0000 (09:19 -0800)]
Merge tag 'dmaengine-fix-4.5-rc5' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"A few fixes for drivers, nothing major here.
Fixes are: iotdma fix to restart channels, new ID for wildcat PCH,
residue fix for edma, disable irq for non-cyclic in dw"
* tag 'dmaengine-fix-4.5-rc5' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: dw: disable BLOCK IRQs for non-cyclic xfer
dmaengine: edma: fix residue race for cyclic
dmaengine: dw: pci: add ID for WildcatPoint PCH
dmaengine: IOATDMA: fix timer code that continues to restart channels during idle
Linus Torvalds [Sat, 20 Feb 2016 17:16:51 +0000 (09:16 -0800)]
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk driver fixes from Stephen Boyd:
"An assortment of vendor specific clk drivers fixes, most notably
fallout from adding Tegra210 and rockchip rk3036/rk3368 drivers this
cycle.
There's also the random smattering of sparse/checker fixes, a build
"fix" to get the Tango clk driver to compile because the Kconfig
symbol was renamed after the fact, and a clk gpio fix for a patch
mismerge"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (28 commits)
clk: gpio: Really allow an optional clock= DT property
Revert "clk: qcom: Specify LE device endianness"
clk: versatile: mask VCO bits before writing
clk: tegra: super: Fix sparse warnings for functions not declared as static
clk: tegra: Fix sparse warnings for functions not declared as static
clk: tegra: Fix sparse warning for pll_m
clk: tegra: Use definition for pll_u override bit
clk: tegra: Fix warning caused by pll_u failing to lock
clk: tegra: Fix clock sources for Tegra210 EMC
clk: tegra: Add the APB2APE audio clock on Tegra210
clk: tegra: Add missing of_node_put()
clk: tegra: Fix PLLE SS coefficients
clk: tegra: Fix typos around clearing PLLE bits during enable
clk: tegra: Do not disable PLLE when under hardware control
clk: tegra: Fix pllx dyn step calculation
clk: tegra: pll: Fix potential sleeping-while-atomic
clk: tegra: Fix the misnaming of nvenc from msenc
clk: tegra: Fix naming of MISC registers
clk: tango4: rename ARCH_TANGOX to ARCH_TANGO
clk: scpi: Fix checking return value of platform_device_register_simple()
...
Linus Torvalds [Sat, 20 Feb 2016 17:13:18 +0000 (09:13 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull more drm fixes from Dave Airlie:
"Some more fixes trickled in:
A bunch of VC4 ones since it's a pretty new driver not much chance of
regressions, and it fixes GPU resets.
Also one atomic fix, one set of fixes for a common bug in TTM cleanup,
and one i915 hotplug fix"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau: use post-decrement in error handling
drm/atomic: Allow for holes in connector state, v2.
drm/i915: Fix hpd live status bits for g4x
drm/vc4: Use runtime PM to power cycle the device when the GPU hangs.
drm/vc4: Enable runtime PM.
drm/vc4: Fix spurious GPU resets due to BO reuse.
drm/vc4: Drop error message on seqno wait timeouts.
drm/vc4: Fix -ERESTARTSYS error return from BO waits.
drm/vc4: Return an ERR_PTR from BO creation instead of NULL.
drm/vc4: Fix the clear color for the first tile rendered.
drm/vc4: Validate that WAIT_BO padding is cleared.
drm/radeon: use post-decrement in error handling
drm/amdgpu: use post-decrement in error handling
Simon Guinot [Wed, 9 Sep 2015 22:15:18 +0000 (00:15 +0200)]
kernel/resource.c: fix muxed resource handling in __request_region()
In __request_region, if a conflict with a BUSY and MUXED resource is
detected, then the caller goes to sleep and waits for the resource to be
released. A pointer on the conflicting resource is kept. At wake-up
this pointer is used as a parent to retry to request the region.
A first problem is that this pointer might well be invalid (if for
example the conflicting resource have already been freed). Another
problem is that the next call to __request_region() fails to detect a
remaining conflict. The previously conflicting resource is passed as a
parameter and __request_region() will look for a conflict among the
children of this resource and not at the resource itself. It is likely
to succeed anyway, even if there is still a conflict.
Instead, the parent of the conflicting resource should be passed to
__request_region().
As a fix, this patch doesn't update the parent resource pointer in the
case we have to wait for a muxed region right after.
Reported-and-tested-by: Vincent Pelletier <plr.vincent@gmail.com> Signed-off-by: Simon Guinot <simon.guinot@sequanux.org> Tested-by: Vincent Donnefort <vdonnefort@gmail.com> Cc: stable@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 19 Feb 2016 21:44:12 +0000 (13:44 -0800)]
Merge tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 bugfixes from Ted Ts'o:
"Miscellaneous ext4 bug fixes for v4.5"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix crashes in dioread_nolock mode
ext4: fix bh->b_state corruption
ext4: fix memleak in ext4_readdir()
ext4: remove unused parameter "newblock" in convert_initialized_extent()
ext4: don't read blocks from disk after extents being swapped
ext4: fix potential integer overflow
ext4: add a line break for proc mb_groups display
ext4: ioctl: fix erroneous return value
ext4: fix scheduling in atomic on group checksum failure
ext4 crypto: move context consistency check to ext4_file_open()
ext4 crypto: revalidate dentry after adding or removing the key
Linus Torvalds [Fri, 19 Feb 2016 21:40:42 +0000 (13:40 -0800)]
Merge branch 'for-linus-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fix from Chris Mason:
"My for-linus-4.5 branch has a btrfs DIO error passing fix.
I know how much you love DIO, so I'm going to suggest against reading
it. We'll follow up with a patch to drop the error arg from
dio_end_io in the next merge window."
* 'for-linus-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix direct IO requests not reporting IO error to user space
Linus Torvalds [Fri, 19 Feb 2016 21:36:00 +0000 (13:36 -0800)]
Merge branch 'akpm' (patches from Andrew)
Merge fixes from Andrew Morton:
"10 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm: slab: free kmem_cache_node after destroy sysfs file
ipc/shm: handle removed segments gracefully in shm_mmap()
MAINTAINERS: update Kselftest Framework mailing list
devm_memremap_release(): fix memremap'd addr handling
mm/hugetlb.c: fix incorrect proc nr_hugepages value
mm, x86: fix pte_page() crash in gup_pte_range()
fsnotify: turn fsnotify reaper thread into a workqueue job
Revert "fsnotify: destroy marks with call_srcu instead of dedicated thread"
mm: fix regression in remap_file_pages() emulation
thp, dax: do not try to withdraw pgtable from non-anon VMA
Linus Torvalds [Fri, 19 Feb 2016 16:40:05 +0000 (08:40 -0800)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Here are some more arm64 fixes for 4.5. This has mostly come from
Yang Shi, who saw some issues under -rt that also affect mainline.
The rest of it is pretty small, but still worth having.
We've got an old issue outstanding with valid_user_regs which will
likely wait until 4.6 (since it would really benefit from some time in
-next) and another issue with kasan and idle which should be fixed
next week.
Apart from that, pretty quiet here (and still no sign of the THP issue
reported on s390...)
Summary:
- Allow EFI stub to use strnlen(), which is required by recent libfdt
- Avoid smp_processor_id() in preempt context during unwinding
- Avoid false Kasan warnings during unwinding
- Ensure early devices are picked up by the IOMMU DMA ops
- Avoid rebuilding the kernel for the 'install' target
- Run fixup handlers for alignment faults on userspace access"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: mm: allow the kernel to handle alignment faults on user accesses
arm64: kbuild: make "make install" not depend on vmlinux
arm64: dma-mapping: fix handling of devices registered before arch_initcall
arm64/efi: Make strnlen() available to the EFI namespace
arm/arm64: crypto: assure that ECB modes don't require an IV
arm64: make irq_stack_ptr more robust
arm64: debug: re-enable irqs before sending breakpoint SIGTRAP
arm64: disable kasan when accessing frame->fp in unwind_frame
Linus Torvalds [Fri, 19 Feb 2016 16:33:12 +0000 (08:33 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"Several bug fixes:
- There are four different stack tracers, and three of them have
bugs. For 4.5 the bugs are fixed and we prepare a cleanup patch
for the next merge window.
- Three bug fixes for the dasd driver in regard to parallel access
volumes and the new max_dev_sectors block device queue limit
- The irq restore optimization needs a fixup for memcpy_real
- The diagnose trace code has a conflict with lockdep"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/dasd: fix performance drop
s390/maccess: reduce stnsm instructions
s390/diag: avoid lockdep recursion
s390/dasd: fix refcount for PAV reassignment
s390/dasd: prevent incorrect length error under z/VM after PAV changes
s390: fix DAT off memory access, e.g. on kdump
s390/oprofile: fix address range for asynchronous stack
s390/perf_event: fix address range for asynchronous stack
s390/stacktrace: add save_stack_trace_regs()
s390/stacktrace: save full stack traces
s390/stacktrace: add missing end marker
s390/stacktrace: fix address ranges for asynchronous and panic stack
s390/stacktrace: fix save_stack_trace_tsk() for current task
Linus Torvalds [Fri, 19 Feb 2016 16:25:40 +0000 (08:25 -0800)]
Merge tag 'pinctrl-v4.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull Pin control fixes from Linus Walleij:
"Pin control fixes for the v4.5 series, all are individual driver
fixes:
- Fix the PXA2xx driver to export its init function so we do not
break modular compiles.
- Hide unused functions in the Nomadik driver.
- Fix up direction control in the Mediatek driver.
- Toggle the sunxi GPIO lines to input when you read them on the H3
GPIO controller, lest you only get garbage.
- Fix up the number of settings in the MVEBU driver.
- Fix a serious SMP race condition in the Samsung driver"
* tag 'pinctrl-v4.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: samsung: fix SMP race condition
pinctrl: mvebu: fix num_settings in mpp group assignment
pinctrl: sunxi: H3 requires irq_read_needs_mux
pinctrl: mediatek: fix direction control issue
pinctrl: nomadik: hide unused functions
pinctrl: pxa: export pxa2xx_pinctrl_init()
Linus Torvalds [Fri, 19 Feb 2016 16:01:41 +0000 (08:01 -0800)]
Merge tag 'sound-4.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This update contains again a few more fixes for ALSA core stuff
although it's no longer high flux: two race fixes in sequencer and one
PCM race fix for non-atomic PCM ops.
In addition, HD-audio gained a similar fix for race at reloading the
driver"
* tag 'sound-4.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: pcm: Fix rwsem deadlock for non-atomic PCM stream
ALSA: seq: Fix double port list deletion
ALSA: hda - Cancel probe work instead of flush at remove
ALSA: seq: Fix leak of pool buffer at concurrent writes
EunTaik Lee [Tue, 16 Feb 2016 04:44:35 +0000 (04:44 +0000)]
arm64: mm: allow the kernel to handle alignment faults on user accesses
Although we don't expect to take alignment faults on access to normal
memory, misbehaving (i.e. buggy) user code can pass MMIO pointers into
system calls, leading to things like get_user accessing device memory.
Rather than OOPS the kernel, allow any exception fixups to run and
return something like -EFAULT back to userspace. This makes the
behaviour more consistent with userspace, even though applications with
access to device mappings can easily cause other issues if they try
hard enough.
Acked-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Eun Taik Lee <eun.taik.lee@samsung.com>
[will: dropped __kprobes annotation and rewrote commit mesage] Signed-off-by: Will Deacon <will.deacon@arm.com>
Masahiro Yamada [Fri, 19 Feb 2016 06:05:50 +0000 (15:05 +0900)]
arm64: kbuild: make "make install" not depend on vmlinux
For the same reason as commit 19514fc665ff ("arm, kbuild: make "make
install" not depend on vmlinux"), the install targets should never
trigger the rebuild of the kernel.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
Jan Kara [Fri, 19 Feb 2016 05:33:21 +0000 (00:33 -0500)]
ext4: fix crashes in dioread_nolock mode
Competing overwrite DIO in dioread_nolock mode will just overwrite
pointer to io_end in the inode. This may result in data corruption or
extent conversion happening from IO completion interrupt because we
don't properly set buffer_defer_completion() when unlocked DIO races
with locked DIO to unwritten extent.
Since unlocked DIO doesn't need io_end for anything, just avoid
allocating it and corrupting pointer from inode for locked DIO.
A cleaner fix would be to avoid these games with io_end pointer from the
inode but that requires more intrusive changes so we leave that for
later.
Cc: stable@vger.kernel.org Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Jan Kara [Fri, 19 Feb 2016 05:18:25 +0000 (00:18 -0500)]
ext4: fix bh->b_state corruption
ext4 can update bh->b_state non-atomically in _ext4_get_block() and
ext4_da_get_block_prep(). Usually this is fine since bh is just a
temporary storage for mapping information on stack but in some cases it
can be fully living bh attached to a page. In such case non-atomic
update of bh->b_state can race with an atomic update which then gets
lost. Usually when we are mapping bh and thus updating bh->b_state
non-atomically, nobody else touches the bh and so things work out fine
but there is one case to especially worry about: ext4_finish_bio() uses
BH_Uptodate_Lock on the first bh in the page to synchronize handling of
PageWriteback state. So when blocksize < pagesize, we can be atomically
modifying bh->b_state of a buffer that actually isn't under IO and thus
can race e.g. with delalloc trying to map that buffer. The result is
that we can mistakenly set / clear BH_Uptodate_Lock bit resulting in the
corruption of PageWriteback state or missed unlock of BH_Uptodate_Lock.
Fix the problem by always updating bh->b_state bits atomically.
CC: stable@vger.kernel.org Reported-by: Nikolay Borisov <kernel@kyup.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Rasmus Villemoes [Mon, 15 Feb 2016 18:41:46 +0000 (19:41 +0100)]
drm/nouveau: use post-decrement in error handling
We need to use post-decrement to get the dma_map_page undone also for
i==0, and to avoid some very unpleasant behaviour if dma_map_page
failed already at i==0.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Reviewed-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
drm/atomic: Allow for holes in connector state, v2.
Because we record connector_mask using 1 << drm_connector_index now
the connector_mask should stay the same even when other connectors
are removed. This was not the case with MST, in that case when removing
a connector all other connectors may change their index.
This is fixed by waiting until the first get_connector_state to allocate
connector_state, and force reallocation when state is too small.
As a side effect connector arrays no longer have to be preallocated,
and can be allocated on first use which means a less allocations in
the page flip only path.
Changes since v1:
- Whitespace. (Ville)
- Call ida_remove when destroying the connector. (Ville)
- u32 alloc -> int. (Ville)
Fixes: 14de6c44d149 ("drm/atomic: Remove drm_atomic_connectors_for_crtc.") Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Lyude <cpaul@redhat.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Stephen Boyd [Fri, 19 Feb 2016 03:07:44 +0000 (19:07 -0800)]
clk: gpio: Really allow an optional clock= DT property
We mis-merged the original patch from Russell here and so the
patch went almost all the way, except that we still failed to
probe when there wasn't a clocks property in the DT node. Allow
that case by making a negative value from
of_clk_get_parent_count() into "no parents", like the original
patch did.
Fixes: 7ed88aa2efa5 ("clk: fix clk-gpio.c with optional clock= DT property") Cc: Russell King <rmk+kernel@arm.linux.org.uk> Cc: Michael Turquette <mturquette@baylibre.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Dave Airlie [Fri, 19 Feb 2016 02:50:00 +0000 (12:50 +1000)]
Merge tag 'drm-vc4-fixes-2016-02-17' of github.com:anholt/linux into drm-fixes
This pull request fixes GPU reset (which was disabled shortly after
V3D integration due to build breakage) and waits for idle in the
presence of signals (which X likes to do a lot).
* tag 'drm-vc4-fixes-2016-02-17' of github.com:anholt/linux:
drm/vc4: Use runtime PM to power cycle the device when the GPU hangs.
drm/vc4: Enable runtime PM.
drm/vc4: Fix spurious GPU resets due to BO reuse.
drm/vc4: Drop error message on seqno wait timeouts.
drm/vc4: Fix -ERESTARTSYS error return from BO waits.
drm/vc4: Return an ERR_PTR from BO creation instead of NULL.
drm/vc4: Fix the clear color for the first tile rendered.
drm/vc4: Validate that WAIT_BO padding is cleared.
Dave Airlie [Fri, 19 Feb 2016 02:49:03 +0000 (12:49 +1000)]
Merge branch 'drm-fixes-4.5' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Just two small fixes in the ttm_tt_populate error handling; one for radeon,
one for amdgpu.
* 'drm-fixes-4.5' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: use post-decrement in error handling
drm/amdgpu: use post-decrement in error handling
Linus Torvalds [Fri, 19 Feb 2016 00:34:15 +0000 (16:34 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatching
Pull livepatching fixes from Jiri Kosina:
- regression (from 4.4) fix for ordering issue, introduced by an
earlier ftrace change, that broke live patching of modules.
The fix replaces the ftrace module notifier by direct call in order
to make the ordering guaranteed and well-defined. The patch, from
Jessica Yu, has been acked both by Steven and Rusty
- error message fix from Miroslav Benes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatching:
ftrace/module: remove ftrace module notifier
livepatch: change the error message in asm/livepatch.h header files
Linus Torvalds [Fri, 19 Feb 2016 00:24:48 +0000 (16:24 -0800)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two simple fixes.
One prevents a soft lockup on some target removal scenarios and the
other prevents us trying to probe the marvell console device, which
causes it to time out and need the bus resetting"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: fix soft lockup in scsi_remove_target() on module removal
SCSI: Add Marvell configuration device to VPD blacklist
Dmitry Safonov [Wed, 17 Feb 2016 21:11:37 +0000 (13:11 -0800)]
mm: slab: free kmem_cache_node after destroy sysfs file
When slub_debug alloc_calls_show is enabled we will try to track
location and user of slab object on each online node, kmem_cache_node
structure and cpu_cache/cpu_slub shouldn't be freed till there is the
last reference to sysfs file.
Separated __kmem_cache_release from __kmem_cache_shutdown which now
called on slab_kmem_cache_release (after the last reference to sysfs
file object has dropped).
Reintroduced locking in free_partial as sysfs file might access cache's
partial list after shutdowning - partial revert of the commit 69cb8e6b7c29 ("slub: free slabs without holding locks"). Zap
__remove_partial and use remove_partial (w/o underscores) as
free_partial now takes list_lock which s partial revert for commit 1e4dd9461fab ("slub: do not assert not having lock in removing freed
partial")
Signed-off-by: Dmitry Safonov <dsafonov@virtuozzo.com> Suggested-by: Vladimir Davydov <vdavydov@virtuozzo.com> Acked-by: Vladimir Davydov <vdavydov@virtuozzo.com> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ipc/shm: handle removed segments gracefully in shm_mmap()
remap_file_pages(2) emulation can reach file which represents removed
IPC ID as long as a memory segment is mapped. It breaks expectations of
IPC subsystem.
Test case (rewritten to be more human readable, originally autogenerated
by syzkaller[1]):
The pmem driver calls devm_memremap() to map a persistent memory range.
When the pmem driver is unloaded, this memremap'd range is not released
so the kernel will leak a vma.
Fix devm_memremap_release() to handle a given memremap'd address
properly.
Signed-off-by: Toshi Kani <toshi.kani@hpe.com> Acked-by: Dan Williams <dan.j.williams@intel.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Ross Zwisler <ross.zwisler@linux.intel.com> Cc: Matthew Wilcox <willy@linux.intel.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vaishali Thakkar [Wed, 17 Feb 2016 21:11:26 +0000 (13:11 -0800)]
mm/hugetlb.c: fix incorrect proc nr_hugepages value
Currently incorrect default hugepage pool size is reported by proc
nr_hugepages when number of pages for the default huge page size is
specified twice.
When multiple huge page sizes are supported, /proc/sys/vm/nr_hugepages
indicates the current number of pre-allocated huge pages of the default
size. Basically /proc/sys/vm/nr_hugepages displays default_hstate->
max_huge_pages and after boot time pre-allocation, max_huge_pages should
equal the number of pre-allocated pages (nr_hugepages).
Test case:
Note that this is specific to x86 architecture.
Boot the kernel with command line option 'default_hugepagesz=1G
hugepages=X hugepagesz=2M hugepages=Y hugepagesz=1G hugepages=Z'. After
boot, 'cat /proc/sys/vm/nr_hugepages' and 'sysctl -a | grep hugepages'
returns the value X. However, dmesg output shows that Z huge pages were
pre-allocated.
So, the root cause of the problem here is that the global variable
default_hstate_max_huge_pages is set if a default huge page size is
specified (directly or indirectly) on the command line. After the command
line processing in hugetlb_init, if default_hstate_max_huge_pages is set,
the value is assigned to default_hstae.max_huge_pages. However,
default_hstate.max_huge_pages may have already been set based on the
number of pre-allocated huge pages of default_hstate size.
The solution to this problem is if hstate->max_huge_pages is already set
then it should not set as a result of global max_huge_pages value.
Basically if the value of the variable hugepages is set multiple times on
a command line for a specific supported hugepagesize then proc layer
should consider the last specified value.
Signed-off-by: Vaishali Thakkar <vaishali.thakkar@oracle.com> Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Hillf Danton <hillf.zj@alibaba-inc.com> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hugh Dickins [Wed, 17 Feb 2016 21:11:23 +0000 (13:11 -0800)]
mm, x86: fix pte_page() crash in gup_pte_range()
Commit 3565fce3a659 ("mm, x86: get_user_pages() for dax mappings") has
moved up the pte_page(pte) in x86's fast gup_pte_range(), for no
discernible reason: put it back where it belongs, after the pte_flags
check and the pfn_valid cross-check.
That may be the cause of the NULL pointer dereference in
gup_pte_range(), seen when vfio called vaddr_get_pfn() when starting a
qemu-kvm based VM.
Signed-off-by: Hugh Dickins <hughd@google.com> Reported-by: Michael Long <Harn-Solo@gmx.de> Tested-by: Michael Long <Harn-Solo@gmx.de> Acked-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jeff Layton [Wed, 17 Feb 2016 21:11:21 +0000 (13:11 -0800)]
fsnotify: turn fsnotify reaper thread into a workqueue job
We don't require a dedicated thread for fsnotify cleanup. Switch it
over to a workqueue job instead that runs on the system_unbound_wq.
In the interest of not thrashing the queued job too often when there are
a lot of marks being removed, we delay the reaper job slightly when
queueing it, to allow several to gather on the list.
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com> Tested-by: Eryu Guan <guaneryu@gmail.com> Reviewed-by: Jan Kara <jack@suse.cz> Cc: Eric Paris <eparis@parisplace.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jeff Layton [Wed, 17 Feb 2016 21:11:18 +0000 (13:11 -0800)]
Revert "fsnotify: destroy marks with call_srcu instead of dedicated thread"
This reverts commit c510eff6beba ("fsnotify: destroy marks with
call_srcu instead of dedicated thread").
Eryu reported that he was seeing some OOM kills kick in when running a
testcase that adds and removes inotify marks on a file in a tight loop.
The above commit changed the code to use call_srcu to clean up the
marks. While that does (in principle) work, the srcu callback job is
limited to cleaning up entries in small batches and only once per jiffy.
It's easily possible to overwhelm that machinery with too many call_srcu
callbacks, and Eryu's reproduer did just that.
There's also another potential problem with using call_srcu here. While
you can obviously sleep while holding the srcu_read_lock, the callbacks
run under local_bh_disable, so you can't sleep there.
It's possible when putting the last reference to the fsnotify_mark that
we'll end up putting a chain of references including the fsnotify_group,
uid, and associated keys. While I don't see any obvious ways that that
could occurs, it's probably still best to avoid using call_srcu here
after all.
This patch reverts the above patch. A later patch will take a different
approach to eliminated the dedicated thread here.
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com> Reported-by: Eryu Guan <guaneryu@gmail.com> Tested-by: Eryu Guan <guaneryu@gmail.com> Cc: Jan Kara <jack@suse.com> Cc: Eric Paris <eparis@parisplace.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The reason is that remap_file_pages() emulation assumes that the target
vma covers whole area we want to over map. That assumption is broken by
first remap_file_pages() call: it split the area into two vma.
The solution is to check next adjacent vmas, if they map the same file
with the same flags.
thp, dax: do not try to withdraw pgtable from non-anon VMA
DAX doesn't deposit pgtables when it maps huge pages: nothing to
withdraw. It can lead to crash.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Matthew Wilcox <willy@linux.intel.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Ross Zwisler <ross.zwisler@linux.intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Takashi Iwai [Wed, 17 Feb 2016 13:30:26 +0000 (14:30 +0100)]
ALSA: pcm: Fix rwsem deadlock for non-atomic PCM stream
A non-atomic PCM stream may take snd_pcm_link_rwsem rw semaphore twice
in the same code path, e.g. one in snd_pcm_action_nonatomic() and
another in snd_pcm_stream_lock(). Usually this is OK, but when a
write lock is issued between these two read locks, the problem
happens: the write lock is blocked due to the first reade lock, and
the second read lock is also blocked by the write lock. This
eventually deadlocks.
The reason is the way rwsem manages waiters; it's queued like FIFO, so
even if the writer itself doesn't take the lock yet, it blocks all the
waiters (including reads) queued after it.
As a workaround, in this patch, we replace the standard down_write()
with an spinning loop. This is far from optimal, but it's good
enough, as the spinning time is supposed to be relatively short for
normal PCM operations, and the code paths requiring the write lock
aren't called so often.
Toshi Kani [Thu, 18 Feb 2016 01:16:54 +0000 (18:16 -0700)]
x86/mm: Fix vmalloc_fault() to handle large pages properly
A kernel page fault oops with the callstack below was observed
when a read syscall was made to a pmem device after a huge amount
(>512GB) of vmalloc ranges was allocated by ioremap() on a x86_64
system:
Since v4.1, ioremap() supports large page (pud/pmd) mappings in
x86_64 and PAE. vmalloc_fault() however assumes that the vmalloc
range is limited to pte mappings.
vmalloc faults do not normally happen in ioremap'd ranges since
ioremap() sets up the kernel page tables, which are shared by
user processes. pgd_ctor() sets the kernel's PGD entries to
user's during fork(). When allocation of the vmalloc ranges
crosses a 512GB boundary, ioremap() allocates a new pud table
and updates the kernel PGD entry to point it. If user process's
PGD entry does not have this update yet, a read/write syscall
to the range will cause a vmalloc fault, which hits the Oops
above as it does not handle a large page properly.
Following changes are made to vmalloc_fault().
64-bit:
- No change for the PGD sync operation as it handles large
pages already.
- Add pud_huge() and pmd_huge() to the validation code to
handle large pages.
- Change pud_page_vaddr() to pud_pfn() since an ioremap range
is not directly mapped (while the if-statement still works
with a bogus addr).
- Change pmd_page() to pmd_pfn() since an ioremap range is not
backed by struct page (while the if-statement still works
with a bogus addr).
32-bit:
- No change for the sync operation since the index3 PGD entry
covers the entire vmalloc range, which is always valid.
(A separate change to sync PGD entry is necessary if this
memory layout is changed regardless of the page size.)
- Add pmd_huge() to the validation code to handle large pages.
This is for completeness since vmalloc_fault() won't happen
in ioremap'd ranges as its PGD entry is always valid.
Reported-by: Henning Schild <henning.schild@siemens.com> Signed-off-by: Toshi Kani <toshi.kani@hpe.com> Acked-by: Borislav Petkov <bp@alien8.de> Cc: <stable@vger.kernel.org> # 4.1+ Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Luis R. Rodriguez <mcgrof@suse.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Toshi Kani <toshi.kani@hp.com> Cc: linux-mm@kvack.org Cc: linux-nvdimm@lists.01.org Link: http://lkml.kernel.org/r/1455758214-24623-1-git-send-email-toshi.kani@hpe.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
Jessica Yu [Tue, 16 Feb 2016 22:32:33 +0000 (17:32 -0500)]
ftrace/module: remove ftrace module notifier
Remove the ftrace module notifier in favor of directly calling
ftrace_module_enable() and ftrace_release_mod() in the module loader.
Hard-coding the function calls directly in the module loader removes
dependence on the module notifier call chain and provides better
visibility and control over what gets called when, which is important
to kernel utilities such as livepatch.
This fixes a notifier ordering issue in which the ftrace module notifier
(and hence ftrace_module_enable()) for coming modules was being called
after klp_module_notify(), which caused livepatch modules to initialize
incorrectly. This patch removes dependence on the module notifier call
chain in favor of hard coding the corresponding function calls in the
module loader. This ensures that ftrace and livepatch code get called in
the correct order on patch module load and unload.
Fixes: 5156dca34a3e ("ftrace: Fix the race between ftrace and insmod") Signed-off-by: Jessica Yu <jeyu@redhat.com> Reviewed-by: Steven Rostedt <rostedt@goodmis.org> Reviewed-by: Petr Mladek <pmladek@suse.cz> Acked-by: Rusty Russell <rusty@rustcorp.com.au> Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com> Reviewed-by: Miroslav Benes <mbenes@suse.cz> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Linus Torvalds [Wed, 17 Feb 2016 19:59:23 +0000 (11:59 -0800)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A collection of fixes from the past few weeks that should go into 4.5.
This contains:
- Overflow fix for sysfs discard show function from Alan.
- A stacking limit init fix for max_dev_sectors, so we don't end up
artificially capping some use cases. From Keith.
- Have blk-mq proper end unstarted requests on a dying queue, instead
of pushing that to the driver. From Keith.
- NVMe:
- Update to Kconfig description for NVME_SCSI, since it was
vague and having it on is important for some SUSE distros.
From Christoph.
- Set of fixes from Keith, around surprise removal. Also kills
the no-merge flag, so it supports merging.
- Set of fixes for lightnvm from Matias, Javier, and Wenwei.
- Fix null_blk oops when asked for lightnvm, but not available. From
Matias.
- Copy-to-user EINTR fix from Hannes, fixing a case where SG_IO fails
if interrupted by a signal.
- Two floppy fixes from Jiri, fixing signal handling and blocking
open.
- A use-after-free fix for O_DIRECT, from Mike Krinkin.
- A block module ref count fix from Roman Pen.
- An fs IO wait accounting fix for O_DSYNC from Stephane Gasparini.
- Smaller reallo fix for xen-blkfront from Bob Liu.
- Removal of an unused struct member in the deadline IO scheduler,
from Tahsin.
- Also from Tahsin, properly initialize inode struct members
associated with cgroup writeback, if enabled.
- From Tejun, ensure that we keep the superblock pinned during cgroup
writeback"
* 'for-linus' of git://git.kernel.dk/linux-block: (25 commits)
blk: fix overflow in queue_discard_max_hw_show
writeback: initialize inode members that track writeback history
writeback: keep superblock pinned during cgroup writeback association switches
bio: return EINTR if copying to user space got interrupted
NVMe: Rate limit nvme IO warnings
NVMe: Poll device while still active during remove
NVMe: Requeue requests on suspended queues
NVMe: Allow request merges
NVMe: Fix io incapable return values
blk-mq: End unstarted requests on dying queue
block: Initialize max_dev_sectors to 0
null_blk: oops when initializing without lightnvm
block: fix module reference leak on put_disk() call for cgroups throttle
nvme: fix Kconfig description for BLK_DEV_NVME_SCSI
kernel/fs: fix I/O wait not accounted for RW O_DSYNC
floppy: refactor open() flags handling
lightnvm: allow to force mm initialization
lightnvm: check overflow and correct mlc pairs
lightnvm: fix request intersection locking in rrpc
lightnvm: warn if irqs are disabled in lock laddr
...
Linus Torvalds [Wed, 17 Feb 2016 19:50:53 +0000 (11:50 -0800)]
Merge tag 'devicetree-fixes-for-4.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree fixes from Rob Herring:
- Fix irq msi-map calculation for nonzero rid-base.
- Binding doc updates for GICv3, fsl-imx-uart, and S3C RTC.
* tag 'devicetree-fixes-for-4.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
rtc: s3c: Document required clocks in the DT binding
serial: fsl-imx-uart: Fix typo in fsl,dte-mode description
dt-bindings: arm, gic-v3: require that reserved cells are always 0
of/irq: Fix msi-map calculation for nonzero rid-base
Linus Torvalds [Wed, 17 Feb 2016 19:45:10 +0000 (11:45 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"This has two main sets of fixes:
- A bunch of Exynos fixes, mainly for their MIC component.
- vblank regression fixes from Mario, apparantly some changes in 4.4
caused some vblank breakage on radeon/nouveau, this set fixes all
the issues seen.
There is also a revert of one of the MST changse, that I was
overzealous in including, that broke 30" MST monitors, and two qxl
fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/qxl: fix erroneous return value
drm/nouveau/display: Enable vblank irqs after display engine is on again.
drm/radeon/pm: Handle failure of drm_vblank_get.
drm: Fix treatment of drm_vblank_offdelay in drm_vblank_on() (v2)
drm: Fix drm_vblank_pre/post_modeset regression from Linux 4.4
drm: Prevent vblank counter bumps > 1 with active vblank clients. (v2)
drm: No-Op redundant calls to drm_vblank_off() (v2)
drm/qxl: use kmalloc_array to alloc reloc_info in qxl_process_single_command
Revert "drm/dp/mst: change MST detection scheme"
drm/exynos/decon: fix disable clocks order
drm/exynos: fix incorrect cpu address for dma_mmap_attrs()
drm/exynos: exynos5433_decon: fix wrong state in decon_vblank_enable
drm/exynos: exynos5433_decon: fix wrong state assignment in decon_enable
drm/exynos: dsi: restore support for drm bridge
drm/exynos: mic: make all functions static
drm/exynos: mic: convert to component framework
drm/exynos: mic: use devm_clk interface
drm/exynos: fix types for compilation on 64bit architectures
drm/exynos: ipp: fix incorrect format specifiers in debug messages
drm/exynos: depend on ARCH_EXYNOS for DRM_EXYNOS
Linus Torvalds [Wed, 17 Feb 2016 19:35:41 +0000 (11:35 -0800)]
Merge tag 'trace-fixes-v4.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"This includes two fixes.
The first is something that has come up a few times and has been
worked out individually, but it's come up now enough that the problem
should be generic. Tracepoints are protected by RCU sched. There are
several tracepoints within core infrastructure like kfree(). If a
tracepoint is called when the CPU is going down, or when it's coming
up but has yet to be recognized by RCU, a RCU warning is triggered.
This is a true bug as that tracepoint is not protected by RCU.
Usually, this is taken care of by testing for cpu online as a
tracepoint condition. But as this is happening more often, moving it
from a individual tracepoint to a check in the tracepoint
infrastructure is more robust.
Note, there is now a duplicate of a cpu online test, because this
update does not remove the individual checks. But the overhead is
small enough that the removal can be done in another release.
The second change is strange linker breakage due to the branch
tracer's builtin_constant_p() check failing, and treating the
condition as a variable instead of a constant. Arnd Bergmann found
that this can be fixed by testing !!(cond) instead of just (cond)"
* tag 'trace-fixes-v4.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix freak link error caused by branch tracer
tracepoints: Do not trace when cpu is offline
powerpc/ioda: Set "read" permission when "write" is set
Quite often drivers set only "write" permission assuming that this
includes "read" permission as well and this works on plenty of
platforms. However IODA2 is strict about this and produces an EEH when
"read" permission is not set and reading happens.
This adds a workaround in the IODA code to always add the "read" bit
when the "write" bit is set.
Fixes: 10b35b2b7485 ("powerpc/powernv: Do not set "read" flag if direction==DMA_NONE") Cc: stable@vger.kernel.org # 4.2+ Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru> Tested-by: Douglas Miller <dougmill@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Ville Syrjälä [Wed, 10 Feb 2016 17:59:05 +0000 (19:59 +0200)]
drm/i915: Fix hpd live status bits for g4x
Looks like g4x hpd live status bits actually agree with the spec. At
least they do on the machine I have, and apparently on Nick Bowler's
g4x as well.
So gm45 may be the only platform where they don't agree. At least
that seems to be the case based on the (somewhat incomplete)
logs/dumps in [1], and Daniel has also tested this on his gm45
sometime in the past.
So let's change the bits to match the spec on g4x. That actually makes
the g4x bits identical to vlv/chv so we can just share the code
between those platforms, leaving gm45 as the special case.
Thomas Gleixner [Tue, 9 Feb 2016 20:11:34 +0000 (20:11 +0000)]
perf/core: Plug potential memory leak in CPU_UP_PREPARE
If CPU_UP_PREPARE is called it is not guaranteed, that a previously allocated
and assigned hash has been freed already, but perf_event_init_cpu()
unconditionally allocates and assignes a new hash if the swhash is referenced.
By overwriting the pointer the existing hash is not longer accessible.
Verify that there is no hash assigned on this cpu before allocating and
assigning a new one.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Vince Weaver <vincent.weaver@maine.edu> Link: http://lkml.kernel.org/r/20160209201007.843269966@linutronix.de Signed-off-by: Ingo Molnar <mingo@kernel.org>
Thomas Gleixner [Tue, 9 Feb 2016 20:11:26 +0000 (20:11 +0000)]
perf/core: Remove the bogus and dangerous CPU_DOWN_FAILED hotplug state
If CPU_DOWN_PREPARE fails the perf hotplug notifier is called for
CPU_DOWN_FAILED and calls perf_event_init_cpu(), which checks whether the
swhash is referenced. If yes it allocates a new hash and stores the pointer in
the per cpu data structure.
But at this point the cpu is still online, so there must be a valid hash
already. By overwriting the pointer the existing hash is not longer
accessible.
Remove the CPU_DOWN_FAILED state, as there is nothing to (re)allocate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Vince Weaver <vincent.weaver@maine.edu> Link: http://lkml.kernel.org/r/20160209201007.763417379@linutronix.de Signed-off-by: Ingo Molnar <mingo@kernel.org>
Thomas Gleixner [Tue, 9 Feb 2016 20:11:20 +0000 (20:11 +0000)]
perf/core: Remove bogus UP_CANCELED hotplug state
If CPU_UP_PREPARE fails the perf hotplug code calls perf_event_exit_cpu(),
which is a pointless exercise. The cpu is not online, so the smp function
calls return -ENXIO. So the result is a list walk to call noops.
Remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Vince Weaver <vincent.weaver@maine.edu> Link: http://lkml.kernel.org/r/20160209201007.682184765@linutronix.de Signed-off-by: Ingo Molnar <mingo@kernel.org>
Stefan Haberland [Fri, 12 Feb 2016 13:50:52 +0000 (14:50 +0100)]
s390/dasd: fix performance drop
Commit ca369d51b ("sd: Fix device-imposed transfer length limits")
introduced a new queue limit max_dev_sectors which limits the maximum
sectors for requests. The default value leads to small dasd requests
and therefor to a performance drop.
Set the max_dev_sectors value to the same value as the max_hw_sectors
to use the maximum available request size for DASD devices.
Signed-off-by: Stefan Haberland <sth@linux.vnet.ibm.com> Cc: stable@vger.kernel.org # 4.4+ Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Toshi Kani [Thu, 11 Feb 2016 21:24:17 +0000 (14:24 -0700)]
x86/uaccess/64: Handle the caching of 4-byte nocache copies properly in __copy_user_nocache()
Data corruption issues were observed in tests which initiated
a system crash/reset while accessing BTT devices. This problem
is reproducible.
The BTT driver calls pmem_rw_bytes() to update data in pmem
devices. This interface calls __copy_user_nocache(), which
uses non-temporal stores so that the stores to pmem are
persistent.
__copy_user_nocache() uses non-temporal stores when a request
size is 8 bytes or larger (and is aligned by 8 bytes). The
BTT driver updates the BTT map table, which entry size is
4 bytes. Therefore, updates to the map table entries remain
cached, and are not written to pmem after a crash.
Change __copy_user_nocache() to use non-temporal store when
a request size is 4 bytes. The change extends the current
byte-copy path for a less-than-8-bytes request, and does not
add any overhead to the regular path.
Reported-and-tested-by: Micah Parrish <micah.parrish@hpe.com> Reported-and-tested-by: Brian Boylston <brian.boylston@hpe.com> Signed-off-by: Toshi Kani <toshi.kani@hpe.com> Cc: <stable@vger.kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Borislav Petkov <bp@alien8.de> Cc: Borislav Petkov <bp@suse.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Luis R. Rodriguez <mcgrof@suse.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ross Zwisler <ross.zwisler@linux.intel.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Toshi Kani <toshi.kani@hp.com> Cc: Vishal Verma <vishal.l.verma@intel.com> Cc: linux-nvdimm@lists.01.org Link: http://lkml.kernel.org/r/1455225857-12039-3-git-send-email-toshi.kani@hpe.com
[ Small readability edits. ] Signed-off-by: Ingo Molnar <mingo@kernel.org>
Heiko Carstens [Fri, 12 Feb 2016 11:40:31 +0000 (12:40 +0100)]
s390/maccess: reduce stnsm instructions
When fixing the DAT off bug ("s390: fix DAT off memory access, e.g.
on kdump") both Christian and I missed that we can save an additional
stnsm instruction.
This saves us a couple of cycles which could improve the speed of
memcpy_real.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Thomas Gleixner [Tue, 16 Feb 2016 22:04:41 +0000 (23:04 +0100)]
perf/x86/amd/uncore: Plug reference leak
In the error path of amd_uncore_cpu_up_prepare() the newly allocated uncore
struct is freed, but the percpu pointer still references it. Set it to NULL.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Vince Weaver <vincent.weaver@maine.edu> Link: http://lkml.kernel.org/r/alpine.DEB.2.11.1602162302170.19512@nanos Signed-off-by: Ingo Molnar <mingo@kernel.org>
Mario Kleiner [Fri, 12 Feb 2016 19:30:32 +0000 (20:30 +0100)]
drm/nouveau/display: Enable vblank irqs after display engine is on again.
In the display resume path, move the calls to drm_vblank_on()
after the point when the display engine is running again.
Since changes were made to drm_update_vblank_count() in Linux 4.4+
to emulate hw vblank counters via vblank timestamping, the function
drm_vblank_on() now needs working high precision vblank timestamping
and therefore working scanout position queries at time of call.
These don't work before the display engine gets restarted, causing
miscalculation of vblank counter increments and thereby large forward
jumps in vblank count at display resume. These jumps can cause client
hangs on resume, or desktop hangs in the case of composited desktops.
Fix this Linux 4.4 regression by reordering calls accordingly.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Cc: <stable@vger.kernel.org> # 4.4+ Cc: Ben Skeggs <bskeggs@redhat.com> Cc: ville.syrjala@linux.intel.com Cc: daniel.vetter@ffwll.ch Cc: dri-devel@lists.freedesktop.org Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com>
Mario Kleiner [Fri, 12 Feb 2016 19:30:30 +0000 (20:30 +0100)]
drm: Fix treatment of drm_vblank_offdelay in drm_vblank_on() (v2)
drm_vblank_offdelay can have three different types of values:
< 0 is to be always treated the same as dev->vblank_disable_immediate
= 0 is to be treated as "never disable vblanks"
> 0 is to be treated as disable immediate if kms driver wants it
that way via dev->vblank_disable_immediate. Otherwise it is
a disable timeout in msecs.
This got broken in Linux 3.18+ for the implementation of
drm_vblank_on. If the user specified a value of zero which should
always reenable vblank irqs in this function, a kms driver could
override the users choice by setting vblank_disable_immediate
to true. This patch fixes the regression and keeps the user in
control.
v2: Only reenable vblank if there are clients left or the user
requested to "never disable vblanks" via offdelay 0. Enabling
vblanks even in the "delayed disable" case (offdelay > 0) was
specifically added by Ville in commit cd19e52aee922
("drm: Kick start vblank interrupts at drm_vblank_on()"),
but after discussion it turns out that this was done by accident.
Citing Ville: "I think it just ended up as a mess due to changing
some of the semantics of offdelay<0 vs. offdelay==0 vs.
disable_immediate during the review of the series. So yeah, given
how drm_vblank_put() works now, I'd just make this check for
offdelay==0."
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: <stable@vger.kernel.org> # 3.18+ Cc: michel@daenzer.net Cc: vbabka@suse.cz Cc: ville.syrjala@linux.intel.com Cc: daniel.vetter@ffwll.ch Cc: dri-devel@lists.freedesktop.org Cc: alexander.deucher@amd.com Cc: christian.koenig@amd.com Signed-off-by: Dave Airlie <airlied@redhat.com>
Mario Kleiner [Fri, 12 Feb 2016 19:30:29 +0000 (20:30 +0100)]
drm: Fix drm_vblank_pre/post_modeset regression from Linux 4.4
Changes to drm_update_vblank_count() in Linux 4.4 broke the
behaviour of the pre/post modeset functions as the new update
code doesn't deal with hw vblank counter resets inbetween calls
to drm_vblank_pre_modeset an drm_vblank_post_modeset, as it
should.
This causes mistreatment of such hw counter resets as counter
wraparound, and thereby large forward jumps of the software
vblank counter which in turn cause vblank event dispatching
and vblank waits to fail/hang --> userspace clients hang.
This symptom was reported on radeon-kms to cause a infinite
hang of KDE Plasma 5 shell's login procedure, preventing users
from logging in.
Fix this by detecting when drm_update_vblank_count() is called
inside a pre->post modeset interval. If so, clamp valid vblank
increments to the safe values 0 and 1, pretty much restoring
the update behavior of the old update code of Linux 4.3 and
earlier. Also reset the last recorded hw vblank count at call
to drm_vblank_post_modeset() to be safe against hw that after
modesetting, dpms on etc. only fires its first vblank irq after
drm_vblank_post_modeset() was already called.
Mario Kleiner [Fri, 12 Feb 2016 19:30:28 +0000 (20:30 +0100)]
drm: Prevent vblank counter bumps > 1 with active vblank clients. (v2)
This fixes a regression introduced by the new drm_update_vblank_count()
implementation in Linux 4.4:
Restrict the bump of the software vblank counter in drm_update_vblank_count()
to a safe maximum value of +1 whenever there is the possibility that
concurrent readers of vblank timestamps could be active at the moment,
as the current implementation of the timestamp caching and updating is
not safe against concurrent readers for calls to store_vblank() with a
bump of anything but +1. A bump != 1 would very likely return corrupted
timestamps to userspace, because the same slot in the cache could
be concurrently written by store_vblank() and read by one of those
readers in a non-atomic fashion and without the read-retry logic
detecting this collision.
Concurrent readers can exist while drm_update_vblank_count() is called
from the drm_vblank_off() or drm_vblank_on() functions or other non-vblank-
irq callers. However, all those calls are happening with the vbl_lock
locked thereby preventing a drm_vblank_get(), so the vblank refcount
can't increase while drm_update_vblank_count() is executing. Therefore
a zero vblank refcount during execution of that function signals that
is safe for arbitrary counter bumps if called from outside vblank irq,
whereas a non-zero count is not safe.
Whenever the function is called from vblank irq, we have to assume concurrent
readers could show up any time during its execution, even if the refcount
is currently zero, as vblank irqs are usually only enabled due to the
presence of readers, and because when it is called from vblank irq it
can't hold the vbl_lock to protect it from sudden bumps in vblank refcount.
Therefore also restrict bumps to +1 when the function is called from vblank
irq.
Such bumps of more than +1 can happen at other times than reenabling
vblank irqs, e.g., when regular vblank interrupts get delayed by more
than 1 frame due to long held locks, long irq off periods, realtime
preemption on RT kernels, or system management interrupts.
A better solution would be to rewrite the timestamp caching to use
full seqlocks to allow concurrent writes and reads for arbitrary
vblank counter increments.
v2: Add code comment that this is essentially a hack and should
be replaced by a full seqlock implementation for caching of
timestamps.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: <stable@vger.kernel.org> # 4.4+ Cc: michel@daenzer.net Cc: vbabka@suse.cz Cc: ville.syrjala@linux.intel.com Cc: daniel.vetter@ffwll.ch Cc: dri-devel@lists.freedesktop.org Cc: alexander.deucher@amd.com Cc: christian.koenig@amd.com Signed-off-by: Dave Airlie <airlied@redhat.com>
Mario Kleiner [Fri, 12 Feb 2016 19:30:27 +0000 (20:30 +0100)]
drm: No-Op redundant calls to drm_vblank_off() (v2)
Otherwise if a kms driver calls into drm_vblank_off() more than once
before calling drm_vblank_on() again, the redundant calls to
vblank_disable_and_save() will call drm_update_vblank_count()
while hw vblank counters and vblank timestamping are in a undefined
state during modesets, dpms off etc.
At least with the legacy drm helpers it is not unusual to
get multiple calls to drm_vblank_off and drm_vblank_on, e.g.,
half a dozen calls to drm_vblank_off and two calls to drm_vblank_on
were observed on radeon-kms during dpms-off -> dpms-on transition.
We don't no-op calls from atomic modesetting drivers, as they
should do a proper job of tracking hw state.
Fixes large jumps of the software maintained vblank counter due to
the hardware vblank counter resetting to zero during dpms off or
modeset, e.g., if radeon-kms is modified to use drm_vblank_off/on
instead of drm_vblank_pre/post_modeset().
This fixes a regression caused by the changes made to
drm_update_vblank_count() in Linux 4.4.
v2: Don't no-op on atomic modesetting drivers, per suggestion
of Daniel Vetter.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: <stable@vger.kernel.org> # 4.4+ Cc: michel@daenzer.net Cc: vbabka@suse.cz Cc: ville.syrjala@linux.intel.com Cc: alexander.deucher@amd.com Cc: christian.koenig@amd.com Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Wed, 17 Feb 2016 04:14:22 +0000 (14:14 +1000)]
Merge branch 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-fixes
Summary:
- fix compilation warnings on ARM64bit.
- fix mic driver initialization.
. MIC is a part of KMS so it converts it to use component framework
like other KMS drivers did.
- fix wrong driver state and disable clock order on DECON driver.
- fix incorrect use of dma_mmap_attrs function.
* 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos/decon: fix disable clocks order
drm/exynos: fix incorrect cpu address for dma_mmap_attrs()
drm/exynos: exynos5433_decon: fix wrong state in decon_vblank_enable
drm/exynos: exynos5433_decon: fix wrong state assignment in decon_enable
drm/exynos: dsi: restore support for drm bridge
drm/exynos: mic: make all functions static
drm/exynos: mic: convert to component framework
drm/exynos: mic: use devm_clk interface
drm/exynos: fix types for compilation on 64bit architectures
drm/exynos: ipp: fix incorrect format specifiers in debug messages
drm/exynos: depend on ARCH_EXYNOS for DRM_EXYNOS
Tahsin Erdogan [Tue, 16 Feb 2016 21:34:39 +0000 (13:34 -0800)]
writeback: initialize inode members that track writeback history
inode struct members that track cgroup writeback information
should be reinitialized when inode gets allocated from
kmem_cache. Otherwise, their values remain and get used by the
new inode.
Eric Anholt [Mon, 8 Feb 2016 20:59:02 +0000 (12:59 -0800)]
drm/vc4: Use runtime PM to power cycle the device when the GPU hangs.
This gets us functional GPU reset again, like we had until a refactor
at merge time. Tested with a little patch to stuff in a broken binner
job every 100 frames.
Eric Anholt [Sat, 6 Feb 2016 01:41:49 +0000 (17:41 -0800)]
drm/vc4: Enable runtime PM.
This may actually get us a feature that the closed driver didn't have:
turning off the GPU in between rendering jobs, while the V3D device is
still opened by the client.
There may be some tuning to be applied here to use autosuspend so that
we don't bounce the device's power so much, but in steady-state
GPU-bound rendering we keep the power on (since we keep multiple jobs
outstanding) and even if we power cycle on every job we can still
manage at least 680 fps.
More importantly, though, runtime PM will allow us to power off the
device to do a GPU reset.
v2: Switch #ifdef to CONFIG_PM not CONFIG_PM_SLEEP (caught by kbuild
test robot)
Eric Anholt [Mon, 8 Feb 2016 19:19:14 +0000 (11:19 -0800)]
drm/vc4: Fix spurious GPU resets due to BO reuse.
We were tracking the "where are the head pointers pointing" globally,
so if another job reused the same BOs and execution was at the same
point as last time we checked, we'd stop and trigger a reset even
though the GPU had made progress.
Eric Anholt [Mon, 25 Jan 2016 22:33:50 +0000 (14:33 -0800)]
drm/vc4: Drop error message on seqno wait timeouts.
These ioctls end up getting exposed to fairly directly to GL users,
and having normal user operations print DRM errors is obviously wrong.
The message was originally to give us some idea of what happened when
a hang occurred, but we have a DRM_INFO from reset for that.
Eric Anholt [Mon, 25 Jan 2016 22:32:41 +0000 (14:32 -0800)]
drm/vc4: Fix -ERESTARTSYS error return from BO waits.
This caused the wait ioctls to claim that waiting had completed when
we actually got interrupted by a signal before it was done. Fixes
broken rendering throttling that produced serious lag in X window
dragging.
Eric Anholt [Mon, 25 Jan 2016 21:52:41 +0000 (13:52 -0800)]
drm/vc4: Fix the clear color for the first tile rendered.
Apparently in hardware (as opposed to simulation), the clear colors
need to be uploaded before the render config, otherwise they won't
take effect. Fixes igt's vc4_wait_bo/used-bo-* subtests.
Linus Torvalds [Tue, 16 Feb 2016 18:50:46 +0000 (10:50 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull ARM KVM fixes from Paolo Bonzini:
- Fix for an unpleasant crash when the VM is created without a timer
- Allow HYP mode to access the full PA space, and not only 40bit
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
arm64: KVM: Configure TCR_EL2.PS at runtime
KVM: arm/arm64: Fix reference to uninitialised VGIC
Tejun Heo [Tue, 16 Feb 2016 18:34:07 +0000 (11:34 -0700)]
writeback: keep superblock pinned during cgroup writeback association switches
If cgroup writeback is in use, an inode is associated with a cgroup
for writeback. If the inode's main dirtier changes to another cgroup,
the association gets updated asynchronously. Nothing was pinning the
superblock while such switches are in progress and superblock could go
away while async switching is pending or in progress leading to
crashes like the following.
Linus Torvalds [Tue, 16 Feb 2016 16:04:06 +0000 (08:04 -0800)]
Merge tag 'for-linus-20160216' of git://git.infradead.org/intel-iommu
Pull IOMMU SVM fixes from David Woodhouse:
"Minor register size and interrupt acknowledgement fixes which only
showed up in testing on newer hardware, but mostly a fix to the MM
refcount handling to prevent a recursive refcount issue when mmap() is
used on the file descriptor associated with a bound PASID"
* tag 'for-linus-20160216' of git://git.infradead.org/intel-iommu:
iommu/vt-d: Clear PPR bit to ensure we get more page request interrupts
iommu/vt-d: Fix 64-bit accesses to 32-bit DMAR_GSTS_REG
iommu/vt-d: Fix mm refcounting to hold mm_count not mm_users
Ingo Molnar [Tue, 16 Feb 2016 15:46:40 +0000 (16:46 +0100)]
Merge tag 'efi-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/mfleming/efi into x86/urgent
Pull EFI bug fixes from Matt Fleming:
* Fix bugs in our code that converts ucs2 strings to utf8 where we
unintentionally drop bits from the original string (Jason Andryuk)
* Add the efi-pstore variables to the variable whitelist so that
users can continue to delete them via efivarfs without needing to
manipulate the immutable flag (Matt Fleming)
Linus Torvalds [Tue, 16 Feb 2016 15:15:20 +0000 (07:15 -0800)]
Merge tag 'spi-fix-v4.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A small clutch of driver specific fixes.
The OMAP one is a bit worrying since it seems to be triggered by some
changes in the runtime PM core code and I suspect there's other
drivers across that are going to be using the same pattern outside of
OMAP but nothing seems to be coming up in the testing people are
doing"
* tag 'spi-fix-v4.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: omap2-mcspi: Fix PM regression with deferred probe for pm_runtime_reinit
spi: bcm2835aux: fix bitmask defines
spi: atmel: fix gpio chip-select in case of non-DT platform
spi/fsl-espi: Correct the maximum transaction length
spi: imx: fix spi resource leak with dma transfer
spi: fix counting in spi-loopback-test code
Linus Torvalds [Tue, 16 Feb 2016 15:13:53 +0000 (07:13 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k fixes from Geert Uytterhoeven:
"Summary:
- Wire up new copy_file_range syscall
- Update defconfigs"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k/defconfig: Update defconfigs for v4.5-rc1
m68k: Wire up copy_file_range
Rasmus Villemoes [Mon, 15 Feb 2016 18:41:47 +0000 (19:41 +0100)]
drm/radeon: use post-decrement in error handling
We need to use post-decrement to get the pci_map_page undone also for
i==0, and to avoid some very unpleasant behaviour if pci_map_page
failed already at i==0.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org
Rasmus Villemoes [Mon, 15 Feb 2016 18:41:45 +0000 (19:41 +0100)]
drm/amdgpu: use post-decrement in error handling
We need to use post-decrement to get the pci_map_page undone also for
i==0, and to avoid some very unpleasant behaviour if pci_map_page
failed already at i==0.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org
Takashi Iwai [Tue, 16 Feb 2016 13:15:59 +0000 (14:15 +0100)]
ALSA: seq: Fix double port list deletion
The commit [7f0973e973cd: ALSA: seq: Fix lockdep warnings due to
double mutex locks] split the management of two linked lists (source
and destination) into two individual calls for avoiding the AB/BA
deadlock. However, this may leave the possible double deletion of one
of two lists when the counterpart is being deleted concurrently.
It ends up with a list corruption, as revealed by syzkaller fuzzer.
This patch fixes it by checking the list emptiness and skipping the
deletion and the following process.
Jason Andryuk [Fri, 12 Feb 2016 23:13:33 +0000 (23:13 +0000)]
lib/ucs2_string: Correct ucs2 -> utf8 conversion
The comparisons should be >= since 0x800 and 0x80 require an additional bit
to store.
For the 3 byte case, the existing shift would drop off 2 more bits than
intended.
For the 2 byte case, there should be 5 bits bits in byte 1, and 6 bits in
byte 2.
Signed-off-by: Jason Andryuk <jandryuk@gmail.com> Reviewed-by: Laszlo Ersek <lersek@redhat.com> Cc: Peter Jones <pjones@redhat.com> Cc: Matthew Garrett <mjg59@coreos.com> Cc: "Lee, Chun-Yi" <jlee@suse.com> Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Matt Fleming [Mon, 15 Feb 2016 10:34:05 +0000 (10:34 +0000)]
efi: Add pstore variables to the deletion whitelist
Laszlo explains why this is a good idea,
'This is because the pstore filesystem can be backed by UEFI variables,
and (for example) a crash might dump the last kilobytes of the dmesg
into a number of pstore entries, each entry backed by a separate UEFI
variable in the above GUID namespace, and with a variable name
according to the above pattern.
Please see "drivers/firmware/efi/efi-pstore.c".
While this patch series will not prevent the user from deleting those
UEFI variables via the pstore filesystem (i.e., deleting a pstore fs
entry will continue to delete the backing UEFI variable), I think it
would be nice to preserve the possibility for the sysadmin to delete
Linux-created UEFI variables that carry portions of the crash log,
*without* having to mount the pstore filesystem.'
There's also no chance of causing machines to become bricked by
deleting these variables, which is the whole purpose of excluding
things from the whitelist.
Use the LINUX_EFI_CRASH_GUID guid and a wildcard '*' for the match so
that we don't have to update the string in the future if new variable
name formats are created for crash dump variables.
Reported-by: Laszlo Ersek <lersek@redhat.com> Acked-by: Peter Jones <pjones@redhat.com> Tested-by: Peter Jones <pjones@redhat.com> Cc: Matthew Garrett <mjg59@srcf.ucam.org> Cc: "Lee, Chun-Yi" <jlee@suse.com> Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Ingo Molnar [Tue, 16 Feb 2016 12:14:57 +0000 (13:14 +0100)]
Merge tag 'efi-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/mfleming/efi into x86/urgent
Pull EFI fixes from Matt Fleming:
* Prevent accidental deletion of EFI variables through efivarfs that
may brick machines. We use a whitelist of known-safe variables to
allow things like installing distributions to work out of the box, and
instead restrict vendor-specific variable deletion by making
non-whitelist variables immutable (Peter Jones)
Thierry Reding [Tue, 16 Feb 2016 10:16:31 +0000 (11:16 +0100)]
arm64/efi: Make strnlen() available to the EFI namespace
Changes introduced in the upstream version of libfdt pulled in by commit 91feabc2e224 ("scripts/dtc: Update to upstream commit b06e55c88b9b") use
the strnlen() function, which isn't currently available to the EFI name-
space. Add it to the EFI namespace to avoid a linker error.
Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Rob Herring <robh@kernel.org> Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
Filipe Manana [Mon, 15 Feb 2016 16:20:26 +0000 (16:20 +0000)]
Btrfs: fix direct IO requests not reporting IO error to user space
If a bio for a direct IO request fails, we were not setting the error in
the parent bio (the main DIO bio), making us not return the error to
user space in btrfs_direct_IO(), that is, it made __blockdev_direct_IO()
return the number of bytes issued for IO and not the error a bio created
and submitted by btrfs_submit_direct() got from the block layer.
This essentially happens because when we call:
dio_end_io(dio_bio, bio->bi_error);
It does not set dio_bio->bi_error to the value of the second argument.
So just add this missing assignment in endio callbacks, just as we do in
the error path at btrfs_submit_direct() when we fail to clone the dio bio
or allocate its private object. This follows the convention of what is
done with other similar APIs such as bio_endio() where the caller is
responsible for setting the bi_error field in the bio it passes as an
argument to bio_endio().
This was detected by the new generic test cases in xfstests: 271, 272,
276 and 278. Which essentially setup a dm error target, then load the
error table, do a direct IO write and unload the error table. They
expect the write to fail with -EIO, which was not getting reported
when testing against btrfs.
Cc: stable@vger.kernel.org # 4.3+ Fixes: 4246a0b63bd8 ("block: add a bi_error field to struct bio") Signed-off-by: Filipe Manana <fdmanana@suse.com>
Youngmin Nam [Mon, 8 Feb 2016 15:49:28 +0000 (00:49 +0900)]
pinctrl: samsung: fix SMP race condition
Previously, samsung_gpio_drection_in/output function were not covered
with a spinlock.
For example, samsung_gpio_direction_output function consists of
two functions.
1. samsung_gpio_set
2. samsung_gpio_set_direction
When 2 CPUs try to control the same gpio pin heavily,
(situation like i2c control with gpio emulation)
This situation can cause below problem.
CPU 0 | CPU1
|
samsung_gpio_direction_output |
samsung_gpio_set(pin A as 1) | samsung_gpio_direction_output
| samsung_gpio_set(pin A as 0)
samsung_gpio_set_direction |
| samsung_gpio_set_direction
The initial value of pin A will be set as 0 while we wanted to set pin A as 1.
This patch modifies samsung_gpio_direction_in/output function
to be done in one spinlock to fix race condition.
Additionally, the new samsung_gpio_set_value was added to implement
gpio set callback(samsung_gpio_set) with spinlock using this function.
Cc: stable@vger.kernel.org Signed-off-by: Youngmin Nam <ym0914@gmail.com> Acked-by: Tomasz Figa <tomasz.figa@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Arnd Bergmann [Fri, 12 Feb 2016 21:26:42 +0000 (22:26 +0100)]
tracing: Fix freak link error caused by branch tracer
In my randconfig tests, I came across a bug that involves several
components:
* gcc-4.9 through at least 5.3
* CONFIG_GCOV_PROFILE_ALL enabling -fprofile-arcs for all files
* CONFIG_PROFILE_ALL_BRANCHES overriding every if()
* The optimized implementation of do_div() that tries to
replace a library call with an division by multiplication
* code in drivers/media/dvb-frontends/zl10353.c doing
In this case, gcc fails to determine whether the divisor
in do_div() is __builtin_constant_p(). In particular, it
concludes that __builtin_constant_p(adc_clock) is false, while
__builtin_constant_p(!!adc_clock) is true.
That in turn throws off the logic in do_div() that also uses
__builtin_constant_p(), and instead of picking either the
constant- optimized division, and the code in ilog2() that uses
__builtin_constant_p() to figure out whether it knows the answer at
compile time. The result is a link error from failing to find
multiple symbols that should never have been called based on
the __builtin_constant_p():
dvb-frontends/zl10353.c:138: undefined reference to `____ilog2_NaN'
dvb-frontends/zl10353.c:138: undefined reference to `__aeabi_uldivmod'
ERROR: "____ilog2_NaN" [drivers/media/dvb-frontends/zl10353.ko] undefined!
ERROR: "__aeabi_uldivmod" [drivers/media/dvb-frontends/zl10353.ko] undefined!
This patch avoids the problem by changing __trace_if() to check
whether the condition is known at compile-time to be nonzero, rather
than checking whether it is actually a constant.
I see this one link error in roughly one out of 1600 randconfig builds
on ARM, and the patch fixes all known instances.
Link: http://lkml.kernel.org/r/1455312410-1058841-1-git-send-email-arnd@arndb.de Acked-by: Nicolas Pitre <nico@linaro.org> Fixes: ab3c9c686e22 ("branch tracer, intel-iommu: fix build with CONFIG_BRANCH_TRACER=y") Cc: stable@vger.kernel.org # v2.6.30+ Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
projects / mirror_ubuntu-kernels.git / log