Arnd Bergmann [Wed, 25 Mar 2020 21:19:04 +0000 (22:19 +0100)]
Merge tag 'uniphier-dt64-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into arm/dt
UniPhier ARM64 SoC DT updates for v5.7
- Rename nodes to avoid dt-schema warnings
- Enable SPI for PXs3 reference board
- Enable thermal monitor for PXs3 SoC
- Fix clock and reset of SPI nodes
* tag 'uniphier-dt64-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
arm64: dts: uniphier: Set SCSSI clock and reset IDs for each channel
arm64: dts: uniphier: Add nodes of thermal monitor and thermal zone for PXs3
arm64: dts: uniphier: Enable spi node for PXs3 reference board
arm64: dts: uniphier: rename NAND node names to follow json-schema
arm64: dts: uniphier: rename aidet node names to follow json-schema
arm64: dts: uniphier: change SD/eMMC node names to follow json-schema
Arnd Bergmann [Wed, 25 Mar 2020 21:01:56 +0000 (22:01 +0100)]
Merge tag 'v5.7-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt
Support for the rk3399-based Pinebook Pro, eDP support and power-tree for
the rk3399 evaluation board, a big number of fixes for issues found by
checking against the new yaml dt-bindings.
And on the smaller side, fixes for network transfers, the mute gpio
on rk3328 gets actually described and one lvds fix on the px30 and
the rk3399-hugsun board gets IR and power led.
* tag 'v5.7-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (27 commits)
arm64: dts: rockchip: Add Hugsun X99 power led
arm64: dts: rockchip: Add Hugsun X99 IR receiver
arm64: dts: rockchip: remove clock-names property from 'generic-ohci' nodes
arm64: dts: rockchip: remove clock-names property from 'generic-ehci' nodes
arm64: dts: rockchip: remove properties from spdif node RK3399 Excavator
arm64: dts: add bus to rockchip amba nodenames
arm64: dts: rockchip: replace clock-freq-min-max by max-frequency
arm64: dts: rockchip: fix vqmmc-supply property name for rk3399 puma
arm64: dts: remove no-emmc from mmc node for Rockchip PX5 EVB
arm64: dts: rockchip: remove rockchip,grf from vop nodes for px30
arm64: dts: rockchip: remove max-freq from &spi1 node for Hugsun X99
arm64: dts: rockchip: fix compatible property for rk3399-evb
arm64: dts: rockchip: Add initial support for Pinebook Pro
dt-bindings: Add doc for Pine64 Pinebook Pro
arm64: dts: rockchip: Enable eDP display on rk3399 evb
arm64: dts: rockchip: remove enable-gpio of backlight on rk3399 evb
arm64: dts: rockchip: Add pmic dt tree for rk3399 evb
arm64: dts: rockchip: remove dvs2 pinctrl for pmic on rk3399 evb
arm64: dts: rockchip: fix px30 lvds ports
arm64: dts: rockchip: Add txpbl node for RK3399/RK3328
...
Arnd Bergmann [Wed, 25 Mar 2020 20:52:09 +0000 (21:52 +0100)]
Merge tag 'samsung-dt-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM changes for v5.7
1. Various fixes:
- Reboot of some Odroid Exynos4412-based boards,
- MMC regulators on Arndale5250,
- Memory mapping on Artik5,
- GPU power domain on Exynos542x boards,
- LCD SPI polarity on UniversalC210,
2. Add thermal cooling of GPU on Odroid XU3/XU4 family,
3. Add dynamic-power-coefficient to Exynos5422 for energy model.
* tag 'samsung-dt-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Fix polarity of the LCD SPI bus on UniversalC210 board
ARM: dts: exynos: Fix G3D power domain supply on Arndale Octa boards
ARM: dts: exynos: Fix G3D power domain supply on Odroid XU3/XU4/HC1 boards
ARM: dts: exynos: Fix memory on Artik5 evaluation boards
ARM: dts: exynos: Make fixed regulators always-on on Arndale5250
ARM: dts: exynos: Fix MMC regulator on Arndale5250 board
ARM: dts: exynos: Add dynamic-power-coefficient to Exynos5422 CPUs
ARM: dts: exynos: Add GPU thermal zone cooling maps for Odroid XU3/XU4/HC1
ARM: dts: exynos: Fix broken reboot on some Odroid U2/X2/U3 boards
Arnd Bergmann [Wed, 25 Mar 2020 20:49:53 +0000 (21:49 +0100)]
Merge tag 'ux500-dts-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into arm/dt
Ux500 DTS updates for the v5.7 kernel:
- Fix some DSI nodes
- Add GT-S7710 DTS file
* tag 'ux500-dts-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: dts: Add devicetree for Samsung GT-S7710
ARM: dts: ux500: Fix up DSI controller nodes
Arnd Bergmann [Wed, 25 Mar 2020 20:48:17 +0000 (21:48 +0100)]
Merge tag 'tegra-for-5.7-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt
arm64: tegra: Device tree changes for v5.7-rc1
These changes add support for the XUSB pad controller, as well as the
XUSB controller on Tegra194. Furthermore, USB device mode is supported
across Tegra210 and Tegra186 boards. PCIe endpoint mode support is added
for the Jetson AGX Xavier platform.
Various minor fixes eliminate warnings on boot related to missing power
supplies for some devices.
* tag 'tegra-for-5.7-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Add support for PCIe endpoint mode in P2972-0000 platform
arm64: tegra: Add PCIe endpoint controllers nodes for Tegra194
arm64: tegra: Add ethernet alias on Jetson TX1
arm64: tegra: Populate LP8557 backlight regulator
arm64: tegra: Fix Tegra186 SOR supply
arm64: tegra: Add EEPROM supplies
arm64: tegra: Enable I2C controller for EEPROM
arm64: tegra: smaug: Change clk_out_2 provider to PMC
arm64: tegra: Add clock-cells property to Tegra PMC node
arm64: tegra: Enable XUDC node on Jetson Nano
arm64: tegra: Update OTG port entries for Jetson Nano
arm64: tegra: Enable XUDC node on Jetson TX2
arm64: tegra: Add XUDC node for Tegra186
arm64: tegra: Enable XUDC on Jetson TX1
arm64: tegra: Add XUDC node for Tegra210
arm64: tegra: Update OTG port entries for Jetson TX2
arm64: tegra: Update OTG port entries for Jetson TX1
arm64: tegra: Enable XUSB host in P2972-0000 board
arm64: tegra: Add XUSB and pad controller on Tegra194
arm64: tegra: Fix Tegra194 PCIe compatible string
Arnd Bergmann [Wed, 25 Mar 2020 20:47:16 +0000 (21:47 +0100)]
Merge tag 'tegra-for-5.7-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt
ARM: tegra: Device tree changes for v5.7-rc1
Minor fixes and additions for 32-bit Tegra SoC device trees.
* tag 'tegra-for-5.7-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Update sound node clocks in device tree
ARM: tegra: Add clock-cells property to PMC
ARM: tegra: Remove USB 2-0 port from Jetson TK1 padctl
Arnd Bergmann [Wed, 25 Mar 2020 20:45:02 +0000 (21:45 +0100)]
Merge tag 'stm32-dt-for-v5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/dt
STM32 DT updates for v5.3, round 1
Highlights:
----------
- Add support for DH Electronics DHCOM SoM and PDK2 rev. 400 carrier
board. It is based on stm32mp157c SoC.
- Add OTG full support on stm32mp15.
- Fix issues seen during yaml validation on stpmic and stmfx.
- Add i2c power/wakeup support on stm32mp15.
- Add card detect on sdcard on stm32mp boards
* tag 'stm32-dt-for-v5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (25 commits)
ARM: dts: stm32: use correct vqmmc regu for eMMC on stm32mp1 ED1/EV1 boards
ARM: dts: stm32: add disable-wp property for SD-card on STM32MP1 boards
ARM: dts: stm32: add cd-gpios properties for SD-cards on STM32MP1 boards
ARM: dts: stm32: Do clean up in stmpic nodes on stm32mp15 boards
ARM: dts: stm32: Rename stmfx joystick pins on stm32mp157c-ev1
ARM: dts: stm32: add cpu clock-frequency property on stm32mp15x
ARM: dts: stm32: add wakeup-source in all I2C nodes of stm32mp157c
ARM: dts: stm32: add i2c4 sleep pinctrl on stm32mp157c-ed1
ARM: dts: stm32: add i2c2/i2c5 sleep pinctrl on stm32mp157c-ev1
ARM: dts: stm32: add i2c4 sleep pinctrl on stm32mp15xx-dkx
ARM: dts: stm32: set i2c4 bus freq to 400KHz on stm32mp15 DK boards
ARM: dts: stm32: set i2c4 bus freq to 400KHz on stm32mp157c-ed1
ARM: dts: stm32: Correct stmfx node name on stm32mp157c-ev1 board
ARM: dts: stm32: Correct stmfx node name on stm32746g-eval board
ARM: dts: stm32: add resets property on all DMA nodes on stm32mp151
ARM: dts: stm32: enable USB OTG Dual Role on stm32mp157c-ev1
ARM: dts: stm32: add USB OTG pinctrl to stm32mp15
ARM: dts: stm32: add USB OTG full support on stm32mp151
ARM: dts: stm32: remove useless properties in stm32mp157a-avenger96 stmpic node
ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board
...
Arnd Bergmann [Wed, 25 Mar 2020 20:44:14 +0000 (21:44 +0100)]
Merge tag 'renesas-dt-bindings-for-v5.7-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt
Renesas DT binding updates for v5.7
- Document support for the M3ULCB board with R-Car M3-W+.
* tag 'renesas-dt-bindings-for-v5.7-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
dt-bindings: arm: renesas: Add M3ULCB with R-Car M3-W+
Arnd Bergmann [Wed, 25 Mar 2020 20:43:28 +0000 (21:43 +0100)]
Merge tag 'renesas-arm64-dt-for-v5.7-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM64 DT updates for v5.7 (take two)
- Thermal support for R-Car M3-W+,
- Support for the M3ULCB board with R-Car M3-W+,
- CPUIdle support for R-Car M3-N and E3,
- Display support for the HiHope RZ/G2M board,
- A minor fix.
* tag 'renesas-arm64-dt-for-v5.7-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
arm64: dts: renesas: Add HiHope RZ/G2M board with idk-1110wr display
arm64: dts: renesas: r8a77990: Add CPUIdle support for CA53 cores
arm64: dts: renesas: r8a77965: Add CPUIdle support for CA57 cores
arm64: dts: renesas: r8a77961: salvator-xs: Fix memory unit-address
arm64: dts: renesas: Add support for M3ULCB with R-Car M3-W+
arm64: dts: renesas: r8a77961: Add thermal nodes
Arnd Bergmann [Wed, 25 Mar 2020 20:42:02 +0000 (21:42 +0100)]
Merge tag 'sunxi-dt-for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
Allwinner Device Tree Changes for v5.7
A fairly large set of changes for v5.7, including some new devices.
SoC specific changes:
- SPI on H6 SoC enabled
- Thermal sensor on R40 SoC enabled
- Deinterlace core hardware on A64 SoC enabled
- Redundant assigned-clocks properties removed
- required clock rates are now enforced by drivers
- LVDS panel support on A20 SoC enabled
- PMU compatible fixed for H5 and H6 SoCs
- Thermal trip points added for A83T and H5 SoCs
- (Image) Rotation core hardware on A83T and A64 SoCs enabled
Device specific changes:
- Pine64 PineTab and PinePhone added
- Various cleanups and improvements for Pine64 PineBook
- GPIO pin bank regulator supplies added for A64-OlinXino
- eMMC enabled on Orange Pi 3
- PocketBook Touch Lux 3 added
- Linutronix Testbox v2 added
- Ethernet enabled on Orange Pi One Plus
- HDMI enabled on H6-based Orange Pi boards
Arnd Bergmann [Wed, 25 Mar 2020 20:41:31 +0000 (21:41 +0100)]
Merge tag 'arm-soc/for-5.7/devicetree' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM-based SoCs Device Tree changes
for 5.7, please pull the following:
- Stefan adds GPIO labels to the Raspberry Pi 4 Model B board DTS
- Nicolas moves the eMMC2 controller into its separate node in order for
platform firmware to perform the necessary "dma-ranges" property
patching based on the chip revision since the eMMC controller has
different addressing constraints.
- Florian convers a whole bunch of Broadcom boards bindings from text to
YAML.
* tag 'arm-soc/for-5.7/devicetree' of https://github.com/Broadcom/stblinux:
dt-bindings: arm: Document Broadcom SoCs 'secondary-boot-reg'
dt-bindings: arm: bcm: Convert Vulcan to YAML
dt-bindings: arm: bcm: Convert BCM11351 to YAML
dt-bindings: arm: bcm: Convert BCM4708 to YAML
dt-bindings: arm: bcm: Convert BCM23550 to YAML
dt-bindings: arm: bcm: Convert BCM21664 to YAML
dt-bindings: arm: bcm: Convert Stingray to YAML
dt-bindings: arm: bcm: Convert Northstar 2 to YAML
dt-bindings: arm: bcm: Convert Northstar Plus to YAML
dt-bindings: arm: bcm: Convert Hurricane 2 to YAML
dt-bindings: arm: bcm: Convert Cygnus to YAML
ARM: dts: bcm2711: Move emmc2 into its own bus
ARM: dts: bcm2711-rpi-4-b: Add SoC GPIO labels
Chunyan Zhang [Wed, 11 Mar 2020 11:21:20 +0000 (19:21 +0800)]
arm64: dts: specify console via command line
The SPRD serial driver need to know which serial port would be used as
console in an early period during initialization, otherwise console
init would fail since we added this feature[1].
So this patch add console to command line via devicetree.
Arnd Bergmann [Wed, 25 Mar 2020 20:39:15 +0000 (21:39 +0100)]
Merge tag 'versatile-dts-v5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into arm/dt
Versatile DTS updates for the v5.7 series take one:
- Schema validation for the top level of all ARM reference
designs: Integrator, Versatile, RealView, Juno.
- Clean up some node names in the trees so they pass
validation fine.
- Drop the old text bindings.
- A top level DMA ranges patch from Rob.
* tag 'versatile-dts-v5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM/arm64: dts: Rename SMB bus to just bus
dt-bindings: arm: Drop the non-YAML bindings
dt-bindings: arm: Add Versatile Express and Juno YAML schema
dt-bindings: arm: Add RealView YAML schema
dt-bindings: arm: Add Versatile YAML schema
dt-bindings: arm: Add Integrator YAML schema
ARM: dts: RealView: Fix the name of the SoC node
ARM: dts: Versatile: Use syscon as node name for IB2
ARM: dts: integratorap: Remove top level dma-ranges
Arnd Bergmann [Wed, 25 Mar 2020 20:20:18 +0000 (21:20 +0100)]
Merge tag 'renesas-arm-dt-for-v5.7-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM DT updates for v5.7
- Miscellaneous fixes and improvements.
* tag 'renesas-arm-dt-for-v5.7-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
ARM: dts: rzg1: Add reset control properties for display
ARM: dts: rcar-gen2: Add reset control properties for display
ARM: dts: r8a7745: Convert to new DU DT bindings
ARM: dts: r7s72100: Add SPIBSC clocks
ARM: dts: renesas: Group tuples in operating-points properties
ARM: dts: renesas: Add missing ethernet PHY reset GPIO on Gen2 reference boards
Johan Jonker [Thu, 12 Mar 2020 17:22:39 +0000 (18:22 +0100)]
arm64: dts: rockchip: remove properties from spdif node RK3399 Excavator
An expermental test with the command below gives this error:
arch/arm64/boot/dts/rockchip/rk3399-sapphire-excavator.dt.yaml:
spdif@ff870000:
'i2c-scl-falling-time-ns', 'i2c-scl-rising-time-ns', 'power-domains'
do not match any of the regexes: 'pinctrl-[0-9]+'
'i2c-scl-falling-time-ns', 'i2c-scl-rising-time-ns'
are not valid properties for 'spdif' nodes, so remove them.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/sound/rockchip-spdif.yaml
Johan Jonker [Wed, 11 Mar 2020 16:25:23 +0000 (17:25 +0100)]
ARM: dts: rockchip: swap clocks and clock-names values for i2s nodes
Current dts files with 'i2s' nodes are manually verified.
In order to automate this process rockchip-i2s.txt
has to be converted to yaml. In the new setup dtbs_check with
rockchip-i2s.yaml expect clocks and clock-names values
in the same order. Fix this for some older Rockchip models.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/sound/rockchip-i2s.yaml
Johan Jonker [Thu, 12 Mar 2020 17:22:40 +0000 (18:22 +0100)]
ARM: dts: rockchip: swap clocks and clock-names values for spdif nodes
Current dts files with 'spdif' nodes are manually verified.
In order to automate this process rockchip-spdif.txt
has to be converted to yaml. In the new setup dtbs_check with
rockchip-spdif.yaml expect clocks and clock-names values
in the same order. Fix this for some older Rockchip models.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/sound/rockchip-spdif.yaml
Johan Jonker [Fri, 13 Mar 2020 13:26:46 +0000 (14:26 +0100)]
ARM: dts: rockchip: remove clock-frequency from saradc node rv1108
An experimental test with the command below gives these errors:
arch/arm/boot/dts/rv1108-elgin-r1.dt.yaml: adc@1038c000:
'clock-frequency'
does not match any of the regexes: 'pinctrl-[0-9]+'
arch/arm/boot/dts/rv1108-evb.dt.yaml: adc@1038c000:
'clock-frequency'
does not match any of the regexes: 'pinctrl-[0-9]+'
'clock-frequency' is not a valid property for a saradc node,
so remove it.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/iio/adc/
rockchip-saradc.yaml
A test with the command below gives for example this error:
arch/arm/boot/dts/rk3066a-bqcurie2.dt.yaml:
l2-cache-controller@10138000: $nodename:0:
'l2-cache-controller@10138000'
does not match '^(cache-controller|cpu)(@[0-9a-f,]+)*$'
Fix error by changing nodename to 'cache-controller'.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/arm/l2c2x0.yaml
Christian Hewitt [Mon, 16 Mar 2020 03:20:54 +0000 (07:20 +0400)]
arm64: dts: meson: add thermal zones to meson gx devices
Adapt and update current VIM2 thermal zones support so that zones are
available on all meson GXBB/GXL/GXM devices - similar to changes made
for G12A/G12B/SM1 devices.
Kunihiko Hayashi [Fri, 13 Mar 2020 00:58:11 +0000 (09:58 +0900)]
arm64: dts: uniphier: Add nodes of thermal monitor and thermal zone for PXs3
Add nodes of thermal monitor and thermal zone for UniPhier PXs3 SoC.
The thermal monitor node is included in sysctrl. This patch gives the
default value for PXs3 in the same way as LD20.
Amit Kucheria [Thu, 5 Mar 2020 22:00:15 +0000 (03:30 +0530)]
arm64: dts: marvell: Fix cpu compatible for AP807-quad
make -k ARCH=arm64 dtbs_check shows the following errors. Fix them by
removing the "arm,armv8" compatible.
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9130-db.dt.yaml:
cpu@0: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9130-db.dt.yaml:
cpu@0: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long CHECK
arch/arm64/boot/dts/renesas/r8a774a1-hihope-rzg2m-ex.dt.yaml
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9130-db.dt.yaml:
cpu@1: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9130-db.dt.yaml:
cpu@1: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9130-db.dt.yaml:
cpu@100: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9130-db.dt.yaml:
cpu@100: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9130-db.dt.yaml:
cpu@101: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9130-db.dt.yaml:
cpu@101: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9131-db.dt.yaml:
cpu@0: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9131-db.dt.yaml:
cpu@0: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9131-db.dt.yaml:
cpu@1: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9131-db.dt.yaml:
cpu@1: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9131-db.dt.yaml:
cpu@100: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9131-db.dt.yaml:
cpu@100: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9131-db.dt.yaml:
cpu@101: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9131-db.dt.yaml:
cpu@101: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9132-db.dt.yaml:
cpu@0: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9132-db.dt.yaml:
cpu@0: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9132-db.dt.yaml:
cpu@1: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9132-db.dt.yaml:
cpu@1: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9132-db.dt.yaml:
cpu@100: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9132-db.dt.yaml:
cpu@100: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9132-db.dt.yaml:
cpu@101: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9132-db.dt.yaml:
cpu@101: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Vadym Kochan [Sun, 9 Feb 2020 21:20:30 +0000 (21:20 +0000)]
arm64: dts: marvell: fix non-existed cpu referrence in armada-ap806-dual.dtsi
armada-ap806-dual.dtsi includes armada-ap806.dtsi which describes
thermal zones for 4 cpus but only cpu0 and cpu1 only exists for dual
configuration, this makes dtb compilation fail. Fix it by removing
thermal zone nodes for non-existed cpus for dual configuration.
arm64: dts: marvell: espressobin: indicate dts version
The commit introducing ESPRESSObin variants didn't specify dts version,
and because of that they are treated by dtc as legacy ones. Fix that by
properly specifying version in each dts.
Fixes: 447b8789359f ("arm64: dts: marvell: add ESPRESSObin variants") Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
arm64: dts: marvell: espressobin: add ethernet alias
The maker of this board and its variants, stores MAC address in U-Boot
environment. Add alias for bootloader to recognise, to which ethernet
node inject the factory MAC address.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Russell King [Thu, 27 Feb 2020 12:08:58 +0000 (12:08 +0000)]
arm64: dts: mcbin: support 2W SFP modules
Allow the SFP cages to be used with 2W SFP modules.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Russell King [Tue, 25 Feb 2020 11:45:12 +0000 (11:45 +0000)]
arm64: dts: clearfog-gt-8k: set gigabit PHY reset deassert delay
If the mv88e6xxx DSA driver is built as a module, it causes the
ethernet driver to re-probe when it's loaded. This in turn causes
the gigabit PHY to be momentarily reset and reprogrammed. However,
we attempt to reprogram the PHY immediately after deasserting reset,
and the PHY ignores the writes.
This results in the PHY operating in the wrong mode, and the copper
link states down.
Set a reset deassert delay of 10ms for the gigabit PHY to avoid this.
Fixes: babc5544c293 ("arm64: dts: clearfog-gt-8k: 1G eth PHY reset signal") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Acked-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Yann Gautier [Wed, 4 Mar 2020 08:09:55 +0000 (09:09 +0100)]
ARM: dts: stm32: add disable-wp property for SD-card on STM32MP1 boards
On STM32MP1 DK1, DK2, ED1 and EV1 boards, there is only a micro SD socket.
This is also the case on Avenger board.
They don't support the Write Protect pin.
The disable-wp is then added in the SD-cards sdmmc1 nodes.
This avoids executing some code and a warning during driver probe.
Linus Walleij [Sat, 7 Mar 2020 19:36:27 +0000 (20:36 +0100)]
ARM: dts: Add devicetree for Samsung GT-S7710
The Samsung GT-S7710 also known as XCover 2 or Skomer is a
Ux500-based mobile phone. In the source code release from
Samsung's open source site it is referred to as "Skomer".
ARM: tegra: Update sound node clocks in device tree
clk_out_1, clk_out_2, and clk_out_3 are part of Tegra PMC block but were
previously erroneously provided by the clock and reset controller.
clk_out_1 is dedicated for audio mclk on Tegra30 through Tegra210.
This patch updates device tree sound node to use clk_out_1 from the PMC
provider as mclk and uses assigned-clock properties to specify clock
parents for clk_out_1 and extern1.
Tegra PMC has clk_out_1, clk_out_2, clk_out_3, and blink clock.
These clocks were erroneously provided by the clock and reset controller
and are now provided by the PMC instead because that's where the primary
controls are.
This patch adds #clock-cells property with 1 clock specifier to the
Tegra PMC node in device tree.
Add device-tree binding documentation for the XUSB device mode controller
present on Tegra210 and Tegra186 SoC. This controller supports the USB 3.0
specification.
Add usb-role-switch property for Tegra210 and Tegra186 platforms. This
entry is used by XUSB pad controller driver to register for role changes
for OTG/Peripheral capable USB 2 ports.
JC Kuo [Wed, 12 Feb 2020 06:11:31 +0000 (14:11 +0800)]
dt-bindings: phy: tegra: Add Tegra194 support
Extend the bindings to cover the set of features found in Tegra194.
Note that, technically, there are four more supplies connected to the
XUSB pad controller (DVDD_PEX, DVDD_PEX_PLL, HVDD_PEX and HVDD_PEX_PLL)
, but the power sequencing requirements of Tegra194 require these to be
under the control of the PMIC.
Tegra194 XUSB PADCTL supports up to USB 3.1 Gen 2 speed, however, it
is possible for some platforms have long signal trace that could not
provide sufficient electrical environment for Gen 2 speed. This patch
adds a "maximum-speed" property to usb3 ports which can be used to
specify the maximum supported speed for any particular USB 3.1 port.
For a port that is not capable of SuperSpeedPlus, "maximum-speed"
property should carry "super-speed".
Signed-off-by: JC Kuo <jckuo@nvidia.com> Acked-by: Thierry Reding <treding@nvidia.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Thierry Reding <treding@nvidia.com>
Vidya Sagar [Tue, 3 Mar 2020 18:10:51 +0000 (23:40 +0530)]
arm64: tegra: Add support for PCIe endpoint mode in P2972-0000 platform
Add endpoint mode support for PCIe C5 controller in P2972-0000 platform
with information about supplies, PHY, PERST GPIO and GPIO that controls
PCIe reference clock coming from the host system.
Jon Hunter [Mon, 24 Feb 2020 14:34:35 +0000 (14:34 +0000)]
arm64: tegra: Fix Tegra186 SOR supply
The following warning is observed on the Jetson TX2 platform ...
WARNING KERN tegra-sor 15540000.sor: 15540000.sor supply \
vdd-hdmi-dp-pll not found, using dummy regulator
The problem is caused because the regulator for the SOR device is
missing the '-supply' suffix in Device-Tree. Therefore, add the
'-supply' suffix to fix this warning.
Fixes: 3fdfaf8718fa ("arm64: tegra: Enable DP support on Jetson TX2") Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
Jon Hunter [Mon, 24 Feb 2020 14:34:33 +0000 (14:34 +0000)]
arm64: tegra: Enable I2C controller for EEPROM
Commit a5b6b67364cb ("arm64: tegra: Add ID EEPROM for Jetson TX1
module") populated the EEPROM on the Jetson TX1 module, but did not
enable the corresponding I2C controller. Enable the I2C controller so
that this EEPROM can be accessed.
Fixes: a5b6b67364cb ("arm64: tegra: Add ID EEPROM for Jetson TX1 module") Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
arm64: tegra: Add clock-cells property to Tegra PMC node
Tegra132 and Tegra210 PMC blocks have clk_out_1, clk_out_2, clk_out_3,
and a blink clock as a part of the PMC.
These clocks were erroneously provided by the clock and reset controller
and are now provided by the PMC instead because that's where the primary
controls are.
Clock IDs for these clocks are defined in the PMC dt-bindings.
This patch updates the device tree to include the PMC dt-bindings header
and adds the #clock-cells property with one clock specifier to the PMC
node.
Jon Hunter [Fri, 14 Feb 2020 13:53:53 +0000 (13:53 +0000)]
arm64: tegra: Fix Tegra194 PCIe compatible string
If the kernel configuration option CONFIG_PCIE_DW_PLAT_HOST is enabled
then this can cause the kernel to incorrectly probe the generic
designware PCIe platform driver instead of the Tegra194 designware PCIe
driver. This causes a boot failure on Tegra194 because the necessary
configuration to access the hardware is not performed.
The order in which the compatible strings are populated in Device-Tree
is not relevant in this case, because the kernel will attempt to probe
the device as soon as a driver is loaded and if the generic designware
PCIe driver is loaded first, then this driver will be probed first.
Therefore, to fix this problem, remove the "snps,dw-pcie" string from
the compatible string as we never want this driver to be probe on
Tegra194.
Fixes: 2602c32f15e7 ("arm64: tegra: Add P2U and PCIe controller nodes to Tegra194 DT") Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
Fabrizio Castro [Wed, 11 Mar 2020 20:03:40 +0000 (20:03 +0000)]
arm64: dts: renesas: Add HiHope RZ/G2M board with idk-1110wr display
The HiHope RZ/G2M is advertised as compatible with panel idk-1110wr
from Advantech, however the panel isn't sold alongside the board.
A new dts, adding everything that's required to get the panel to
work with HiHope RZ/G2M, is the most convenient way to support the
HiHope RZ/G2M when it's connected to the idk-1110wr.
Yuya Hamamachi [Mon, 9 Mar 2020 06:44:25 +0000 (15:44 +0900)]
arm64: dts: renesas: Add support for M3ULCB with R-Car M3-W+
Add initial support for the Renesas M3ULCB board equipped with an R-Car
M3-W+ SiP with 8 (2 x 4) GiB of RAM.
To avoid build error on 'ulcb.dtsi', ssi2 is added into 'r8a77961.dtsi'.
Based on commit 92980759c1699a3c ("arm64: dts: renesas: Add support for
Salvator-XS with R-Car M3-W+").