Even after disabling interrupts on the module, it could be possible
that irq handlers are still running. System hang is seen during
suspend path. It was found that, there were pending writes on the
HDA bus and clock was disabled by that time.
Above mentioned issue is fixed by clearing any pending irq handlers
before disabling clocks and returning from hda suspend.
An initial commit to add tracepoints for packets without CIP headers
uses different print formats for added tracepoints. However this is not
convenient for users/developers to prepare debug tools.
This commit uses the same format for the two tracepoints.
An initial commit to add tracepoints for packets without CIP headers
introduces a wrong assignment to 'data_blocks' value of
'out_packet_without_header' tracepoint.
In IEC 61883-1/6 engine of ALSA firewire stack, a packet handler has a
second argument for 'the number of bytes in payload of isochronous
packet'. However, an incoming packet handler without CIP header uses the
value as 'the number of quadlets in the payload'. This brings userspace
applications to receive the number of PCM frames as four times against
real time.
According to my memo at hand and saved records, writing 0x00000001 to
SND_FF_REG_FETCH_PCM_FRAMES disables fetching PCM frames in corresponding
channel, however current implement uses reversed logic. This results in
muted volume in device side during playback.
I ran into a link-time error with the atmel-quadspi driver on the
EBSA110 platform:
drivers/mtd/built-in.o: In function `atmel_qspi_run_command':
:(.text+0x1ee3c): undefined reference to `_memcpy_toio'
:(.text+0x1ee48): undefined reference to `_memcpy_fromio'
The problem is that _memcpy_toio/_memcpy_fromio are not available on
that platform, and we have to prevent building the driver there.
In case we want to backport this to older kernels: between linux-4.8
and linux-4.20, the Kconfig entry was in drivers/mtd/spi-nor/Kconfig
but had the same problem.
Link: https://lore.kernel.org/patchwork/patch/812860/ Fixes: 161aaab8a067 ("mtd: atmel-quadspi: add driver for Atmel QSPI controller") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Al Viro mentioned (Message-ID
<20170626041334.GZ10672@ZenIV.linux.org.uk>)
that there is probably a race condition
lurking in accesses of sk_stamp on 32-bit machines.
sock->sk_stamp is of type ktime_t which is always an s64.
On a 32 bit architecture, we might run into situations of
unsafe access as the access to the field becomes non atomic.
Use seqlocks for synchronization.
This allows us to avoid using spinlocks for readers as
readers do not need mutual exclusion.
Another approach to solve this is to require sk_lock for all
modifications of the timestamps. The current approach allows
for timestamps to have their own lock: sk_stamp_lock.
This allows for the patch to not compete with already
existing critical sections, and side effects are limited
to the paths in the patch.
The addition of the new field maintains the data locality
optimizations from
commit 9115e8cd2a0c ("net: reorganize struct sock for better data
locality")
Note that all the instances of the sk_stamp accesses
are either through the ioctl or the syscall recvmsg.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
clcsock can be released while kernel_accept() references it in TCP
listen worker. Also, clcsock needs to wake up before released if TCP
fallback is used and the clcsock is blocked by accept. Add a lock to
safely release clcsock and call kernel_sock_shutdown() to wake up
clcsock from accept in smc_release().
Reported-by: syzbot+0bf2e01269f1274b4b03@syzkaller.appspotmail.com Reported-by: syzbot+e3132895630f957306bc@syzkaller.appspotmail.com Signed-off-by: Myungho Jung <mhjungk@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When TIPC_NLA_UDP_REMOTE is an IPv6 mcast address but
TIPC_NLA_UDP_LOCAL is an IPv4 address, a NULL-ptr deref is triggered
as the UDP tunnel sock is initialized to IPv4 or IPv6 sock merely
based on the protocol in local address.
We should just error out when the remote address and local address
have different protocols.
Reported-by: syzbot+eb4da3a20fad2e52555d@syzkaller.appspotmail.com Cc: Ying Xue <ying.xue@windriver.com> Cc: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
lock_sock() must be used in process context to be race-free with
other lock_sock() callers, for example, tipc_release(). Otherwise
using the spinlock directly can't serialize a parallel tipc_release().
As it is blocking, we have to hold the sock refcnt before
rhashtable_walk_stop() and release it after rhashtable_walk_start().
Fixes: 07f6c4bc048a ("tipc: convert tipc reference table to use generic rhashtable") Reported-by: Dmitry Vyukov <dvyukov@google.com> Cc: Ying Xue <ying.xue@windriver.com> Cc: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
During the firmware flash process, some of the EMADs get timed out, which
causes the driver to send them again with a limit of 5 retries. There are
some situations in which 5 retries is not enough and the EMAD access fails.
If the failed EMAD was related to the flashing process, the driver fails
the flashing.
The reason for these timeouts during firmware flashing is cache misses in
the CPU running the firmware. In case the CPU needs to fetch instructions
from the flash when a firmware is flashed, it needs to wait for the
flashing to complete. Since flashing takes time, it is possible for pending
EMADs to timeout.
Fix by increasing EMADs' timeout while flashing firmware.
Fixes: ce6ef68f433f ("mlxsw: spectrum: Implement the ethtool flash_device callback") Signed-off-by: Shalom Toledo <shalomt@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When the completion queue of the RQ is empty, do not immediately return.
If left-over decompressed CQEs (from the previous cycle) were processed,
need to go to the finalization part of the poll function.
Bug exists only when CQE compression is turned ON.
This solves the following issue:
mlx5_core 0000:82:00.1: mlx5_eq_int:544:(pid 0): CQ error on CQN 0xc08, syndrome 0x1
mlx5_core 0000:82:00.1 p4p2: mlx5e_cq_error_event: cqn=0x000c08 event=0x04
Fixes: 4b7dfc992514 ("net/mlx5e: Early-return on empty completion queues") Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
At least old Xen net backends seem to send frags with no real data
sometimes. In case such a fragment happens to occur with the frag limit
already reached the frontend will BUG currently even if this situation
is easily recoverable.
Modify the BUG_ON() condition accordingly.
Tested-by: Dietmar Hahn <dietmar.hahn@ts.fujitsu.com> Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If a server side socket is bound to an address, but not in the listening
state yet, incoming connection requests should receive a reset control
packet in response. However, the function used to send the reset
silently drops the reset packet if the sending socket isn't bound
to a remote address (as is the case for a bound socket not yet in
the listening state). This change fixes this by using the src
of the incoming packet as destination for the reset packet in
this case.
Fixes: d021c344051a ("VSOCK: Introduce VM Sockets") Reviewed-by: Adit Ranadive <aditr@vmware.com> Reviewed-by: Vishnu Dasa <vdasa@vmware.com> Signed-off-by: Jorgen Hansen <jhansen@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We miss a write barrier that guarantees used idx is updated and seen
before log. This will let userspace sync and copy used ring before
used idx is update. Fix this by adding a barrier before log_write().
Fixes: 8dd014adfea6f ("vhost-net: mergeable buffers support") Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Alexei reported use after frees in inet_diag_dump_icsk() [1]
Because we use refcount_set() when various sockets are setup and
inserted into ehash, we also need to make sure inet_diag_dump_icsk()
wont race with the refcount_set() operations.
Jonathan Lemon sent a patch changing net_twsk_hashdance() but
other spots would need risky changes.
Instead, fix inet_diag_dump_icsk() as this bug came with
linux-4.10 only.
[1] Quoting Alexei :
First something iterating over sockets finds already freed tw socket:
Fixes: 67db3e4bfbc9 ("tcp: no longer hold ehash lock while calling tcp_get_info()") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Alexei Starovoitov <ast@kernel.org> Cc: Jonathan Lemon <jonathan.lemon@gmail.com> Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
syzbot reported a kernel-infoleak, which is caused by an uninitialized
field(sin6_flowinfo) of addr->a.v6 in sctp_inet6addr_event().
The call trace is as below:
__ptr_ring_swap_queue() tries to move pointers from the old
ring to the new one, but it forgets to check if ->producer
is beyond the new size at the end of the operation. This leads
to an out-of-bound access in __ptr_ring_produce() as reported
by syzbot.
Reported-by: syzbot+8993c0fa96d57c399735@syzkaller.appspotmail.com Fixes: 5d49de532002 ("ptr_ring: resize support") Cc: "Michael S. Tsirkin" <mst@redhat.com> Cc: John Fastabend <john.fastabend@gmail.com> Cc: Jason Wang <jasowang@redhat.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Packet sockets with SOCK_DGRAM may pass an address for use in
dev_hard_header. Ensure that it is of sufficient length.
Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
nr_find_socket(), nr_find_peer() and nr_find_listener() lock the
sock after finding it in the global list. However, the call path
requires BH disabled for the sock lock consistently.
Actually the locking is unnecessary at this point, we can just hold
the sock refcnt to make sure it is not gone after we unlock the global
list, and lock it later only when needed.
Reported-and-tested-by: syzbot+f621cda8b7e598908efa@syzkaller.appspotmail.com Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Even though the link is down before entering hibernation,
there is an issue that the network interface always links up after resuming
from hibernation.
If the link is still down before enabling the network interface,
and after resuming from hibernation, the phydev->state is forcibly set
to PHY_UP in mdio_bus_phy_restore(), and the link becomes up.
In suspend sequence, only if the PHY is attached, mdio_bus_phy_suspend()
calls phy_stop_machine(), and mdio_bus_phy_resume() calls
phy_start_machine().
In resume sequence, it's enough to do the same as mdio_bus_phy_resume()
because the state has been preserved.
This patch fixes the issue by calling phy_start_machine() in
mdio_bus_phy_restore() in the same way as mdio_bus_phy_resume().
Fixes: bc87922ff59d ("phy: Move PHY PM operations into phy_device") Suggested-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
On some platforms (currently detected only on SAMA5D4) TX might stuck
even the pachets are still present in DMA memories and TX start was
issued for them. This happens due to race condition between MACB driver
updating next TX buffer descriptor to be used and IP reading the same
descriptor. In such a case, the "TX USED BIT READ" interrupt is asserted.
GEM/MACB user guide specifies that if a "TX USED BIT READ" interrupt
is asserted TX must be restarted. Restart TX if used bit is read and
packets are present in software TX queue. Packets are removed from software
TX queue if TX was successful for them (see macb_tx_interrupt()).
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Local variable description: ----data.i@capi_unlocked_ioctl
Variable was created at:
capi_ioctl drivers/isdn/capi/capi.c:747 [inline]
capi_unlocked_ioctl+0x82/0x1bf0 drivers/isdn/capi/capi.c:939
do_vfs_ioctl+0xebd/0x2bf0 fs/ioctl.c:46
Bytes 12-63 of 64 are uninitialized
Memory access of size 64 starts at ffff88807ac5fce8
Data copied to user address 0000000020000080
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Cc: Karsten Keil <isdn@linux-pingi.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
xfrm6_policy_check() might have re-allocated skb->head, we need
to reload ipv6 header pointer.
sysbot reported :
BUG: KASAN: use-after-free in __ipv6_addr_type+0x302/0x32f net/ipv6/addrconf_core.c:40
Read of size 4 at addr ffff888191b8cb70 by task syz-executor2/1304
Memory state around the buggy address: ffff888191b8ca00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff888191b8ca80: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb
>ffff888191b8cb00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff888191b8cb80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff888191b8cc00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
Fixes: 0d3c703a9d17 ("ipv6: Cleanup IPv6 tunnel receive path") Fixes: ed1efb2aefbb ("ipv6: Add support for IPsec virtual tunnel interfaces") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
syzbot reported the use of uninitialized udp6_addr::sin6_scope_id.
We can just set ::sin6_scope_id to zero, as tunnels are unlikely
to use an IPv6 address that needs a scope id and there is no
interface to bind in this context.
For net-next, it looks different as we have cfg->bind_ifindex there
so we can probably call ipv6_iface_scope_id().
Same for ::sin6_flowinfo, tunnels don't use it.
Fixes: 8024e02879dd ("udp: Add udp_sock_create for UDP tunnels to open listener socket") Reported-by: syzbot+c56449ed3652e6720f30@syzkaller.appspotmail.com Cc: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Packet sockets may call dev_header_parse with NULL daddr. Make
lowpan_header_ops.create fail.
Fixes: 87a93e4eceb4 ("ieee802154: change needed headroom/tailroom") Signed-off-by: Willem de Bruijn <willemb@google.com> Acked-by: Alexander Aring <aring@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 33a48ab105a7 ("ibmveth: Fix DMA unmap error") fixed an issue in the
normal code path of ibmveth_xmit_start() that was originally introduced by
Commit 6e8ab30ec677 ("ibmveth: Add scatter-gather support"). This original
fix missed the error path where dma_unmap_page is wrongly called on the
header portion in descs[0] which was mapped with dma_map_single. As a
result a failure to DMA map any of the frags results in a dmesg warning
when CONFIG_DMA_API_DEBUG is enabled.
------------[ cut here ]------------
DMA-API: ibmveth 30000002: device driver frees DMA memory with wrong function
[device address=0x000000000a430000] [size=172 bytes] [mapped as page] [unmapped as single]
WARNING: CPU: 1 PID: 8426 at kernel/dma/debug.c:1085 check_unmap+0x4fc/0xe10
...
<snip>
...
DMA-API: Mapped at:
ibmveth_start_xmit+0x30c/0xb60
dev_hard_start_xmit+0x100/0x450
sch_direct_xmit+0x224/0x490
__qdisc_run+0x20c/0x980
__dev_queue_xmit+0x1bc/0xf20
This fixes the API misuse by unampping descs[0] with dma_unmap_single.
Fixes: 6e8ab30ec677 ("ibmveth: Add scatter-gather support") Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Add napi_disable routine in gro_cells_destroy since starting from
commit c42858eaf492 ("gro_cells: remove spinlock protecting receive
queues") gro_cell_poll and gro_cells_destroy can run concurrently on
napi_skbs list producing a kernel Oops if the tunnel interface is
removed while gro_cell_poll is running. The following Oops has been
triggered removing a vxlan device while the interface is receiving
traffic
1. After freeing dev->ax25_ptr, we need to set it to NULL otherwise
we may use a dangling pointer.
2. There is a race between ax25_setsockopt() and device notifier as
reported by syzbot. Close it by holding RTNL lock.
3. We need to test if dev->ax25_ptr is NULL before using it.
Reported-and-tested-by: syzbot+ae6bb869cbed29b29040@syzkaller.appspotmail.com Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
There's a race between close_ctree() and cleaner_kthread().
close_ctree() sets btrfs_fs_closing(), and the cleaner stops when it
sees it set, but this is racy; the cleaner might have already checked
the bit and could be cleaning stuff. In particular, if it deletes unused
block groups, it will create delayed iputs for the free space cache
inodes. As of "btrfs: don't run delayed_iputs in commit", we're no
longer running delayed iputs after a commit. Therefore, if the cleaner
creates more delayed iputs after delayed iputs are run in
btrfs_commit_super(), we will leak inodes on unmount and get a busy
inode crash from the VFS.
Fix it by parking the cleaner before we actually close anything. Then,
any remaining delayed iputs will always be handled in
btrfs_commit_super(). This also ensures that the commit in close_ctree()
is really the last commit, so we can get rid of the commit in
cleaner_kthread().
The fstest/generic/475 followed by 476 can trigger a crash that
manifests as a slab corruption caused by accessing the freed kthread
structure by a wake up function. Sample trace:
In preparation for libnvdimm growing new restrictions to detect section
conflicts between persistent memory regions, enable nfit_test to
allocate aligned resources. Use a gen_pool to allocate nfit_test's fake
resources in a separate address space from the virtual translation of
the same.
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com> Tested-by: Vishal Verma <vishal.l.verma@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
While trying to use the dma_mmap_*() interface, it was noticed that this
interface returns strange values when passed an incorrect length.
If neither of the if() statements fire then the return value is
uninitialized. In the worst case it returns 0 which means the caller
will think the function succeeded.
Fixes: 1655cf8829d8 ("ARM: dma-mapping: Remove traces of NOMMU code") Signed-off-by: Nathan Jones <nathanj439@gmail.com> Reviewed-by: Robin Murphy <robin.murphy@arm.com> Acked-by: Vladimir Murzin <vladimir.murzin@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Malicious user space may try to force the verifier to use as much cpu
time and memory as possible. Hence check for pending signals
while verifying the program.
Note that suspend of sys_bpf(PROG_LOAD) syscall will lead to EAGAIN,
since the kernel has to release the resources used for program verification.
Reported-by: Anatoly Trosinenko <anatoly.trosinenko@gmail.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Edward Cree <ecree@solarflare.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
A MAC address must be unique among all the macvlan devices with the same
lower device. The only exception is the passthru [sic] mode,
which shares the lower device address.
When duplicate addresses are detected, EBUSY is returned when bringing
the interface up:
# ip link add macvlan0 link eth0 type macvlan
# read addr </sys/class/net/eth0/address
# ip link set macvlan0 address $addr
# ip link set macvlan0 up
RTNETLINK answers: Device or resource busy
Use correct error code which is EADDRINUSE, and do the check also
earlier, on address change:
# ip link set macvlan0 address $addr
RTNETLINK answers: Address already in use
Signed-off-by: Matteo Croce <mcroce@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
SoCs that contain MDP5 have a top level wrapper called MDSS that
manages locks, power and irq for the sub-blocks within it.
Irq for HDMI is also routed through the MDSS.
Shortly after the Hot Plug Detection (HPD) is enabled in HDMI,
HDMI interrupts are recieved by the MDSS interrupt handler.
However at this moment the HDMI irq is still not mapped to
the MDSS irq domain so the HDMI irq handler cannot be called
to process the interrupts.
This leads to a flood of HDMI interrupts on CPU 0.
If we are lucky to have the HDMI initialization running on a
different CPU, it will eventually map the HDMI irq to MDSS irq
domain, the next HDMI interrupt will be handled by the HDMI irq
handler, the interrupt flood will stop and we will recover.
If the HDMI initialization is running on CPU 0, then it cannot
complete and there is nothing to stop the interrupt flood on
CPU 0. The system is stuck.
Fix this by moving the HPD enablement after the HDMI irq is
mapped to the MDSS irq domain.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org> Signed-off-by: Rob Clark <robdclark@gmail.com> Signed-off-by: Sean Paul <seanpaul@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The function lio_vf_rep_packet_sent_callback releases the occupation of
sc via octeon_free_soft_command. sc should not be used after that.
Unfortunately, sc->iq_no is read. To fix this, the patch stores sc->iq_no
into a local variable before releasing sc and then uses the local variable
instead of sc->iq_no.
Signed-off-by: Pan Bian <bianpan2016@163.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Checksum enabled status bits from rx descriptor were incorrectly
interpreted. Consequently all the other valid logic worked on zero bits.
That caused rx checksum offloads never to trigger.
Tested by dumping rx descriptors and validating resulting csum_level.
Reported-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com> Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Fixes: ad703c2b9127f ("net: aquantia: invalid checksumm offload implementation") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Userspace hasn't used submit cmds with submit_offset != 0 for a while,
but this starts cropping up again with cmdstream sub-buffer-allocation
in libdrm_freedreno.
Doesn't do much good to increment the buf ptr before assigning it.
Fixes: 78b8e5b847b4 drm/msm: dump a rd GPUADDR header for all buffers in the command Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com> Signed-off-by: Rob Clark <robdclark@gmail.com> Signed-off-by: Sean Paul <seanpaul@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The current recovery code gets a pointer to the task struct and does a
few things all within the rcu_read_lock. This puts constraints on the
types of gfp flags that can be used within the rcu lock. This patch
instead gets a reference to the task within the rcu lock and releases
the lock immediately, this way the task stays afloat until we need it and
we also get to use the desired gfp flags.
Signed-off-by: Sharat Masetty <smasetty@codeaurora.org> Signed-off-by: Rob Clark <robdclark@gmail.com> Signed-off-by: Sean Paul <seanpaul@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We should check the bus state before reinitializing the IP core.
Otherwise, the internal bus busy state which also tracks multi-master
activity is lost.
Credits go to the Renesas BSP team for suggesting this change.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Fixes: ae481cc13965 ("i2c: rcar: fix resume by always initializing registers before transfer") Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
proc_sys_lookup can fail with ENOMEM instead of ENOENT when the
corresponding sysctl table is being unregistered. In our case we see
this upon opening /proc/sys/net/*/conf files while network interfaces
are being deleted, which confuses our configuration daemon.
The problem was successfully reproduced and this fix tested on v4.9.122
and v4.20-rc6.
v2: return ERR_PTRs in all cases when proc_sys_make_inode fails instead
of mixing them with NULL. Thanks Al Viro for the feedback.
Fixes: ace0c791e6c3 ("proc/sysctl: Don't grab i_lock under sysctl_lock.") Cc: stable@vger.kernel.org Signed-off-by: Ivan Delalande <colona@arista.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
I've noticed, that dying memory cgroups are often pinned in memory by a
single pagecache page. Even under moderate memory pressure they sometimes
stayed in such state for a long time. That looked strange.
My investigation showed that the problem is caused by applying the LRU
pressure balancing math:
UBIFS's recovery code strictly assumes that a deleted inode will never
come back, therefore it removes all data which belongs to that inode
as soon it faces an inode with link count 0 in the replay list.
Before O_TMPFILE this assumption was perfectly fine. With O_TMPFILE
it can lead to data loss upon a power-cut.
Consider a journal with entries like:
0: inode X (nlink = 0) /* O_TMPFILE was created */
1: data for inode X /* Someone writes to the temp file */
2: inode X (nlink = 0) /* inode was changed, xattr, chmod, … */
3: inode X (nlink = 1) /* inode was re-linked via linkat() */
Upon replay of entry #2 UBIFS will drop all data that belongs to inode X,
this will lead to an empty file after mounting.
As solution for this problem, scan the replay list for a re-link entry
before dropping data.
Fixes: 474b93704f32 ("ubifs: Implement O_TMPFILE") Cc: stable@vger.kernel.org # 4.9-4.18 Cc: Russell Senior <russell@personaltelco.net> Cc: Rafał Miłecki <zajec5@gmail.com> Reported-by: Russell Senior <russell@personaltelco.net> Reported-by: Rafał Miłecki <zajec5@gmail.com> Tested-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Richard Weinberger <richard@nod.at>
[rmilecki: update ubifs_assert() calls to compile with 4.18 and older] Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit e58725d51fa8da9133f3f1c54170aa2e43056b91) Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
From printk()/serial console point of view panic() is special, because
it may force CPU to re-enter printk() or/and serial console driver.
Therefore, some of serial consoles drivers are re-entrant. E.g. 8250:
serial8250_console_write()
{
if (port->sysrq)
locked = 0;
else if (oops_in_progress)
locked = spin_trylock_irqsave(&port->lock, flags);
else
spin_lock_irqsave(&port->lock, flags);
...
}
panic() does set oops_in_progress via bust_spinlocks(1), so in theory
we should be able to re-enter serial console driver from panic():
However, this does not happen and we deadlock in serial console on
port->lock spinlock. And the problem is that console_flush_on_panic()
called after bust_spinlocks(0):
bust_spinlocks(0) decrements oops_in_progress, so oops_in_progress
can go back to zero. Thus even re-entrant console drivers will simply
spin on port->lock spinlock. Given that port->lock may already be
locked either by a stopped CPU, or by the very same CPU we execute
panic() on (for instance, NMI panic() on printing CPU) the system
deadlocks and does not reboot.
Fix this by removing bust_spinlocks(0), so oops_in_progress is always
set in panic() now and, thus, re-entrant console drivers will trylock
the port->lock instead of spinning on it forever, when we call them
from console_flush_on_panic().
Link: http://lkml.kernel.org/r/20181025101036.6823-1-sergey.senozhatsky@gmail.com Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Daniel Wang <wonderfly@google.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Alan Cox <gnomes@lxorguk.ukuu.org.uk> Cc: Jiri Slaby <jslaby@suse.com> Cc: Peter Feiner <pfeiner@google.com> Cc: linux-serial@vger.kernel.org Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Signed-off-by: Petr Mladek <pmladek@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Currently the copy_to_user of data in the gentry struct is copying
uninitiaized data in field _pad from the stack to userspace.
Fix this by explicitly memset'ing gentry to zero, this also will zero any
compiler added padding fields that may be in struct (currently there are
none).
Detected by CoverityScan, CID#200783 ("Uninitialized scalar variable")
Fixes: b263b31e8ad6 ("x86, mtrr: Use explicit sizing and padding for the 64-bit ioctls") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Tyler Hicks <tyhicks@canonical.com> Cc: security@kernel.org Link: https://lkml.kernel.org/r/20181218172956.1440-1-colin.king@canonical.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Some guests OSes (including Windows 10) write to MSR 0xc001102c
on some cases (possibly while trying to apply a CPU errata).
Make KVM ignore reads and writes to that MSR, so the guest won't
crash.
The MSR is documented as "Execution Unit Configuration (EX_CFG)",
at AMD's "BIOS and Kernel Developer's Guide (BKDG) for AMD Family
15h Models 00h-0Fh Processors".
The signal delivery path of posix-timers can try to rearm the timer even if
the interval is zero. That's handled for the common case (hrtimer) but not
for alarm timers. In that case the forwarding function raises a division by
zero exception.
The handling for hrtimer based posix timers is wrong because it marks the
timer as active despite the fact that it is stopped.
Move the check from common_hrtimer_rearm() to posixtimer_rearm() to cure
both issues.
Commit 78d3a92edbfb ("gpiolib-acpi: Register GpioInt ACPI event handlers
from a late_initcall") deferred the entire acpi_gpiochip_request_interrupt
call for each event resource.
This means it also delays the gpiochip_request_own_desc(..., "ACPI:Event")
call. This is a problem if some AML code reads the GPIO pin before we
run the deferred acpi_gpiochip_request_interrupt, because in that case
acpi_gpio_adr_space_handler() will already have called
gpiochip_request_own_desc(..., "ACPI:OpRegion") causing the call from
acpi_gpiochip_request_interrupt to fail with -EBUSY and we will fail to
register an event handler.
acpi_gpio_adr_space_handler is prepared for acpi_gpiochip_request_interrupt
already having claimed the pin, but the other way around does not work.
One example of a problem this causes, is the event handler for the OTG
ID pin on a Prowise PT301 tablet not registering, keeping the port stuck
in whatever mode it was in during boot and e.g. only allowing charging
after a reboot.
This commit fixes this by only deferring the request_irq call and the
initial run of edge-triggered IRQs instead of deferring all of
acpi_gpiochip_request_interrupt.
Cc: stable@vger.kernel.org Fixes: 78d3a92edbfb ("gpiolib-acpi: Register GpioInt ACPI event ...") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Some eMMCs from Micron have been reported to need ~800 ms timeout, while
enabling the CACHE ctrl after running sudden power failure tests. The
needed timeout is greater than what the card specifies as its generic CMD6
timeout, through the EXT_CSD register, hence the problem.
Normally we would introduce a card quirk to extend the timeout for these
specific Micron cards. However, due to the rather complicated debug process
needed to find out the error, let's simply use a minimum timeout of 1600ms,
the double of what has been reported, for all cards when enabling CACHE
ctrl.
Reported-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk> Reported-by: Andreas Dannenberg <dannenberg@ti.com> Reported-by: Faiz Abbas <faiz_abbas@ti.com> Cc: <stable@vger.kernel.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In commit 5320226a0512 ("mmc: core: Disable HPI for certain Hynix eMMC
cards"), then intent was to prevent HPI from being used for some eMMC
cards, which didn't properly support it. However, that went too far, as
even BKOPS and CACHE ctrl became prevented. Let's restore those parts and
allow BKOPS and CACHE ctrl even if HPI isn't supported.
Fixes: 5320226a0512 ("mmc: core: Disable HPI for certain Hynix eMMC cards") Cc: Pratibhasagar V <pratibha@codeaurora.org> Cc: <stable@vger.kernel.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
During a re-initialization of the eMMC card, we may fail to re-enable HPI.
In these cases, that isn't properly reflected in the card->ext_csd.hpi_en
bit, as it keeps being set. This may cause following attempts to use HPI,
even if's not enabled. Let's fix this!
When boxes are run near (or to) OOM, we have a problem with the discard
page allocation in sd. If we fail allocating the special page, we return
busy, and it'll get retried. But since ordering is honored for dispatch
requests, we can keep retrying this same IO and failing. Behind that IO
could be requests that want to free memory, but they never get the
chance. This means you get repeated spews of traces like this:
The HP lt4132 is a rebranded Huawei ME906s-158 LTE modem.
The interface with protocol 0x16 is "CDC ECM & NCM" according to the *.inf
files included with the Windows driver. Attaching the option driver to it
doesn't result in a /dev/ttyUSB* device being created, so I've excluded it.
Note that it is also excluded for corresponding Huawei-branded devices, cf.
commit d544db293a44 ("USB: support new huawei devices in option.c").
The code to prevent a bus suspend if a USB3 port was still in link training
also reacted to USB2 port polling state.
This caused bus suspend to busyloop in some cases.
USB2 polling state is different from USB3, and should not prevent bus
suspend.
Limit the USB3 link training state check to USB3 root hub ports only.
The origial commit went to stable so this need to be applied there as well
Fixes: 2f31a67f01a8 ("usb: xhci: Prevent bus suspend if a port connect change or polling state is detected") Cc: stable@vger.kernel.org Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The function hso_probe reads if_num from the USB device (as an u8) and uses
it without a length check to index an array, resulting in an OOB memory read
in hso_probe or hso_get_config_data.
Add a length check for both locations and updated hso_probe to bail on
error.
This issue has been assigned CVE-2018-19985.
Reported-by: Hui Peng <benquike@gmail.com> Reported-by: Mathias Payer <mathias.payer@nebelwelt.net> Signed-off-by: Hui Peng <benquike@gmail.com> Signed-off-by: Mathias Payer <mathias.payer@nebelwelt.net> Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The ESD watchdog code in sta32x_watchdog() dereferences the pointer
which is never assigned.
This is a regression from a1be4cead9b950 ("ASoC: sta32x: Convert to direct
regmap API usage.") which went unnoticed since nobody seems to use that ESD
workaround.
Fixes: a1be4cead9b950 ("ASoC: sta32x: Convert to direct regmap API usage.") Signed-off-by: Daniel Mack <daniel@zonque.org> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If __blkdev_issue_discard is in progress and a device mapper device is
reloaded with a table that doesn't support discard,
q->limits.max_discard_sectors is set to zero. This results in infinite
loop in __blkdev_issue_discard.
This patch checks if max_discard_sectors is zero and aborts with
-EOPNOTSUPP.
struct bioctx includes the ref refcount_t to track the number of I/O
fragments used to process a target BIO as well as ensure that the zone
of the BIO is kept in the active state throughout the lifetime of the
BIO. However, since decrementing of this reference count is done in the
target .end_io method, the function bio_endio() must be called multiple
times for read and write target BIOs, which causes problems with the
value of the __bi_remaining struct bio field for chained BIOs (e.g. the
clone BIO passed by dm core is large and splits into fragments by the
block layer), resulting in incorrect values and inconsistencies with the
BIO_CHAIN flag setting. This is turn triggers the BUG_ON() call:
BUG_ON(atomic_read(&bio->__bi_remaining) <= 0);
in bio_remaining_done() called from bio_endio().
Fix this ensuring that bio_endio() is called only once for any target
BIO by always using internal clone BIOs for processing any read or
write target BIO. This allows reference counting using the target BIO
context counter to trigger the target BIO completion bio_endio() call
once all data, metadata and other zone work triggered by the BIO
complete.
Overall, this simplifies the code too as the target .end_io becomes
unnecessary and differences between read and write BIO issuing and
completion processing disappear.
Fixes: 3b1a94c88b79 ("dm zoned: drive-managed zoned block device target") Cc: stable@vger.kernel.org Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 78e5dfea84dc ("powerpc: dts: replace 'linux,stdout-path' with
'stdout-path'") broke the default console on a number of embedded
PowerPC systems, because it failed to also update the code in
arch/powerpc/kernel/legacy_serial.c to look for that property in
addition to the old one.
This fixes it.
Fixes: 78e5dfea84dc ("powerpc: dts: replace 'linux,stdout-path' with 'stdout-path'") Cc: stable@vger.kernel.org # v4.17+ Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
vb2_start_streaming() already rolls back the buffers, so there is no
need to call __vb2_queue_cancel(). Especially since __vb2_queue_cancel()
does too much, such as zeroing the q->queued_count value, causing vb2
to think that no buffers have been queued.
It appears that this call to __vb2_queue_cancel() is a left-over from
before commit b3379c6201bb3.
Fixes: b3379c6201bb3 ('vb2: only call start_streaming if sufficient buffers are queued') Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Cc: <stable@vger.kernel.org> # for v4.16 and up Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When sending out CMD23 in the blk preparation, the comment there
rightfully says:
* However, it is not sufficient to just send CMD23,
* and avoid the final CMD12, as on an error condition
* CMD12 (stop) needs to be sent anyway. This, coupled
* with Auto-CMD23 enhancements provided by some
* hosts, means that the complexity of dealing
* with this is best left to the host. If CMD23 is
* supported by card and host, we'll fill sbc in and let
* the host deal with handling it correctly.
Let's do this behaviour for RPMB as well, and not send CMD23
independently. Otherwise IP cores (like Renesas SDHI) may timeout
because of automatic CMD23/CMD12 handling.
BugLink: https://bugs.launchpad.net/bugs/1837257
Upstream commit 972910948fb6 ("ARM: dts: qcom: Remove Arrow SD600
eval board") removed this file because there are no known users,
but in linux-4.19.y, we still get a compile-time warnign for it:
arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dtb: Warning (graph_endpoint): /soc/mdp@5100000/ports/port@3/endpoint: graph connection to node '/soc/hdmi-tx@4a00000/ports/port@0/endpoint' is not bidirectional
Address the warning by adding the remote endpoint that makes the link
bidirectional. This is the same property that other boards use.
drivers/scsi/raid_class.c: In function 'raid_match':
drivers/scsi/raid_class.c:64:24: error: unused variable 'i' [-Werror=unused-variable]
This looks like a very old problem that for some reason was very hard to
run into, but it is very easy to fix, by replacing the incorrect #ifdef
with a simpler IS_ENABLED() check.
Fixes: fac829fdcaf4 ("[SCSI] raid_attrs: fix dependency problems") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Nicolas Schichan [Wed, 19 Dec 2018 21:40:42 +0000 (22:40 +0100)]
bpf, arm: fix emit_ldx_r and emit_mov_i using TMP_REG_1
BugLink: https://bugs.launchpad.net/bugs/1837257
emit_ldx_r() and emit_a32_mov_i() were both using TMP_REG_1 and
clashing with each other. Using TMP_REG_2 in emit_ldx_r() fixes
the issue.
Fixes: ec19e02b343 ("ARM: net: bpf: fix LDX instructions") Cc: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Nicolas Schichan <nschichan@freebox.fr> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In order to read correctly from asynchronously updated RTC registers,
it's necessary to read repeatedly until their values do not change from
read to read. It's also necessary to wait for three RTC clock ticks for
certain operations. There are no timeouts in this code and these
operations could possibly loop forever.
To avoid kernel hangs, put in timeouts.
The iMX7d can be configured to stop the SRTC on a tamper event, which
will lockup the kernel inside this driver as described above.
These hangs can happen when running under qemu, which doesn't emulate
the SNVS RTC, though currently the driver will refuse to load on qemu
due to a timeout in the driver probe method.
It could also happen if the SRTC block where somehow placed into reset
or the slow speed clock that drives the SRTC counter (but not the CPU)
were to stop.
The symptoms on a two core iMX7d are a work queue hang on
rtc_timer_do_work(), which eventually blocks a systemd fsnotify
operation that triggers a work queue flush, causing systemd to hang and
thus causing all services that should be started by systemd, like a
console getty, to fail to start or stop.
Also optimize the wait code to wait less. It only needs to wait for the
clock to advance three ticks, not to see it change three times.
Some AMD based HP laptops have a SMB0001 ACPI device node which does not
define any methods.
This leads to the following error in dmesg:
[ 5.222731] cmi: probe of SMB0001:00 failed with error -5
This commit makes acpi_smbus_cmi_add() return -ENODEV instead in this case
silencing the error. In case of a failure of the i2c_add_adapter() call
this commit now propagates the error from that call instead of -EIO.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
According to Intel (R) Axxia TM Lionfish Communication Processor
Peripheral Subsystem Hardware Reference Manual, the AXXIA I2C module
have a programmable Master Wait Timer, which among others, checks the
time between commands send in manual mode. When a timeout (25ms) passes,
TSS bit is set in Master Interrupt Status register and a Stop command is
issued by the hardware.
The axxia_i2c_xfer(), does not properly handle this situation, however.
For each message a separate axxia_i2c_xfer_msg() is called and this
function incorrectly assumes that any interrupt might happen only when
waiting for completion. This is mostly correct but there is one
exception - a master timeout can trigger if enough time has passed
between individual transfers. It will, by definition, happen between
transfers when the interrupts are disabled by the code. If that happens,
the hardware issues Stop command.
The interrupt indicating timeout will not be triggered as soon as we
enable them since the Master Interrupt Status is cleared when master
mode is entered again (which happens before enabling irqs) meaning this
error is lost and the transfer is continued even though the Stop was
issued on the bus. The subsequent operations completes without error but
a bogus value (0xFF in case of read) is read as the client device is
confused because aborted transfer. No error is returned from
master_xfer() making caller believe that a valid value was read.
To fix the problem, the TSS bit (indicating timeout) in Master Interrupt
Status register is checked before each transfer. If it is set, there was
a timeout before this transfer and (as described above) the hardware
already issued Stop command so the transaction should be aborted thus
-ETIMEOUT is returned from the master_xfer() callback. In order to be
sure no timeout was issued we can't just read the status just before
starting new transaction as there will always be a small window of time
(few CPU cycles at best) where this might still happen. For this reason
we have to temporally disable the timer before checking for TSS bit.
Disabling it will, however, clear the TSS bit so in order to preserve
that information, we have to read it in ISR so we have to ensure that
the TSS interrupt is not masked between transfers of one transaction.
There is no need to call bus recovery or controller reinitialization if
that happens so it's skipped.
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com> Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When deleting a VLAN device using an ioctl the netdev is unregistered
before the VLAN filter is updated via ndo_vlan_rx_kill_vid(). It can
lead to a use-after-free in mlxsw in case the VLAN device is deleted
while being enslaved to a bridge.
The reason for the above is that when mlxsw receives the CHANGEUPPER
event, it wrongly assumes that the VLAN device is no longer its upper
and thus destroys the internal representation of the bridge port despite
the reference count being non-zero.
Fix this by checking if the VLAN device is our upper using its real
device. In net-next I'm going to remove this trick and instead make
mlxsw completely agnostic to the order of the events.
Fixes: c57529e1d5d8 ("mlxsw: spectrum: Replace vPorts with Port-VLAN") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If a local process has closed a connected socket and hasn't received a
RST packet yet, then the socket remains in the table until a timeout
expires.
When a vhost_vsock instance is released with the timeout still pending,
the socket is never freed because vhost_vsock has already set the
SOCK_DONE flag.
Check if the close timer is pending and let it close the socket. This
prevents the race which can leak sockets.
Reported-by: Maximilian Riemensberger <riemensberger@cadami.net> Cc: Graham Whaley <graham.whaley@gmail.com> Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When unloading the ast driver, a warning message is printed by
drm_mode_config_cleanup() because a reference is still held to one of
the drm_connector structs.
Correct this by calling drm_crtc_force_disable_all() in
ast_fbdev_destroy().
After getting a reference to the platform device's of_node the probe
function ends up calling of_find_matching_node() using the node as an
argument. The function takes care of decreasing the refcount on it. We
are then incorrectly decreasing the refcount on that node again.
This patch removes the unwarranted call to of_node_put().
Fixes: 414fd46e7762 ("fsl/fman: Add FMan support") Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Chris has discovered and reported that v7_dma_inv_range() may corrupt
memory if address range is not aligned to cache line size.
Since the whole cache-v7m.S was lifted form cache-v7.S the same
observation applies to v7m_dma_inv_range(). So the fix just mirrors
what has been done for v7 with a little specific of M-class.
Cc: Chris Cole <chris@sageembedded.com> Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This patch addresses possible memory corruption when
v7_dma_inv_range(start_address, end_address) address parameters are not
aligned to whole cache lines. This function issues "invalidate" cache
management operations to all cache lines from start_address (inclusive)
to end_address (exclusive). When start_address and/or end_address are
not aligned, the start and/or end cache lines are first issued "clean &
invalidate" operation. The assumption is this is done to ensure that any
dirty data addresses outside the address range (but part of the first or
last cache lines) are cleaned/flushed so that data is not lost, which
could happen if just an invalidate is issued.
The problem is that these first/last partial cache lines are issued
"clean & invalidate" and then "invalidate". This second "invalidate" is
not required and worse can cause "lost" writes to addresses outside the
address range but part of the cache line. If another component writes to
its part of the cache line between the "clean & invalidate" and
"invalidate" operations, the write can get lost. This fix is to remove
the extra "invalidate" operation when unaligned addressed are used.
A kernel module is available that has a stress test to reproduce the
issue and a unit test of the updated v7_dma_inv_range(). It can be
downloaded from
http://ftp.sageembedded.com/outgoing/linux/cache-test-20181107.tgz.
v7_dma_inv_range() is call by dmac_[un]map_area(addr, len, direction)
when the direction is DMA_FROM_DEVICE. One can (I believe) successfully
argue that DMA from a device to main memory should use buffers aligned
to cache line size, because the "clean & invalidate" might overwrite
data that the device just wrote using DMA. But if a driver does use
unaligned buffers, at least this fix will prevent memory corruption
outside the buffer.
Signed-off-by: Chris Cole <chris@sageembedded.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>