Roland Dreier [Mon, 30 Apr 2012 07:15:47 +0000 (07:15 +0000)]
cxgb3: Don't call cxgb_vlan_mode until q locks are initialized
The driver calls cxgb_vlan_mode() from init_one(). This calls into
synchronize_rx(), which locks all the q locks, but the q locks are not
initialized until cxgb_up() -> setup_sge_qsets(). So move the call to
cxgb_vlan_mode() into cxgb_up(), after the call to setup_sge_qsets().
We also move the body of these functions up higher to avoid having to
a forward declaration.
This was found because of the lockdep warning:
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
Pid: 323, comm: work_for_cpu Not tainted 3.4.0-rc5 #28
Call Trace:
[<ffffffff8106e767>] register_lock_class+0x108/0x2d0
[<ffffffff8106ff42>] __lock_acquire+0xd3/0xd06
[<ffffffff81070fd0>] lock_acquire+0xbf/0xfe
[<ffffffff813862a6>] _raw_spin_lock_irq+0x36/0x45
[<ffffffffa01e71aa>] cxgb_vlan_mode+0x96/0xcb [cxgb3]
[<ffffffffa01f90eb>] init_one+0x8c4/0x980 [cxgb3]
[<ffffffff811fcbf0>] local_pci_probe+0x3f/0x70
[<ffffffff81042206>] do_work_for_cpu+0x10/0x22
[<ffffffff810482de>] kthread+0xa1/0xa9
[<ffffffff8138e234>] kernel_thread_helper+0x4/0x10
Contrary to what lockdep says, the code is not fine: we are locking an
uninitialized spinlock.
Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yi Zou [Fri, 20 Apr 2012 05:48:08 +0000 (05:48 +0000)]
ixgbe: fix calling skb_put on nonlinear skb assertion bug
With the support to bounce buffer added, the skb is coming as nonlinear in the
case of non-DDPed data frames for FCoE, which is mostly ok as the FCoE stack
would take care of that. However, for target mode, we have to set the FC CRC
and FC EOF field to allow the protocol stack to not drop the frame for the last
data frame of that sequence. So fix this by linearizing the skb first before
doing skb_put().
Signed-off-by: Yi Zou <yi.zou@intel.com> Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Sat, 17 Mar 2012 02:39:16 +0000 (02:39 +0000)]
ixgbe: Fix a memory leak in IEEE DCB
The driver was freeing memory in shutdown instead of remove. As a result
we were leaking memory if IEEE DCB was enabled and we loaded/unloaded the
driver. This change moves the freeing of the memory into the remove
routine where it belongs.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Acked-by: John Fastabend <john.r.fastabend@intel.com> Tested-by: Ross Brattain <ross.b.brattain@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Samuel Liao [Fri, 27 Apr 2012 17:09:27 +0000 (17:09 +0000)]
igbvf: fix the bug when initializing the igbvf
Maybe it's a typo, but it cause that igbvf can't be initialized successfully.
Set perm_addr value using valid dev_addr, although which is equal to hw.mac.addr.
Signed-off-by: Samuel Liao <samuelliao@tencent.com> Signed-off-by: Shan Wei <davidshan@tencent.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
smsc75xx: enable mac to detect speed/duplex from phy
This patch sets the automatic speed and duplex detection bits
in MAC_CR to enable the mac to determine its speed automatically
from the phy.
Note this must be done BEFORE the receiver or transmitter is
enabled.
Signed-off-by: Stephane Fillod <fillods@users.sf.net> Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net> Signed-off-by: David S. Miller <davem@davemloft.net>
also explicitly set the phy to advertise 1000 speeds
Signed-off-by: Stephane Fillod <fillods@users.sf.net> Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net> Signed-off-by: David S. Miller <davem@davemloft.net>
smsc75xx phy interrupt acknowledge needs an mdio_write to clear
PHY_INT_SRC instead of just a read like in smsc95xx.
Signed-off-by: Stephane Fillod <fillods@users.sf.net> Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Stephane Fillod <fillods@users.sf.net> Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net> Signed-off-by: David S. Miller <davem@davemloft.net>
smsc75xx: add more information to register io failure warnings
Signed-off-by: Stephane Fillod <fillods@users.sf.net> Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net> Signed-off-by: David S. Miller <davem@davemloft.net>
smsc75xx needs MII_ACCESS_BUSY to be set to correctly trigger mdio I/O. Note smsc75xx is different from smsc95xx in this regard.
Signed-off-by: Stephane Fillod <fillods@users.sf.net> Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net> Signed-off-by: David S. Miller <davem@davemloft.net>
When the cwnd reduction is done, ssthresh may be infinite
if TCP enters CWR via ECN or F-RTO. If cwnd is not undone, i.e.,
undo_marker is set, tcp_complete_cwr() falsely set cwnd to the
infinite ssthresh value. The correct operation is to keep cwnd
intact because it has been updated in ECN or F-RTO.
Signed-off-by: Yuchung Cheng <ycheng@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jan Seiffert [Sun, 29 Apr 2012 19:02:19 +0000 (19:02 +0000)]
bpf jit: Let the powerpc jit handle negative offsets
Now the helper function from filter.c for negative offsets is exported,
it can be used it in the jit to handle negative offsets.
First modify the asm load helper functions to handle:
- know positive offsets
- know negative offsets
- any offset
then the compiler can be modified to explicitly use these helper
when appropriate.
This fixes the case of a negative X register and allows to lift
the restriction that bpf programs with negative offsets can't
be jited.
Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Jan Seiffert <kaffeemonster@googlemail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bug is that sk_sockets_allocated_read_positive() calls
percpu_counter_sum_positive() without BH being disabled.
This bug was added in commit 180d8cd942ce33
(foundations of per-cgroup memory pressure controlling.), since previous
code was using percpu_counter_read_positive() which is IRQ safe.
In __sk_mem_schedule() we dont need the precise count of allocated
sockets and can revert to previous behavior.
Reported-by: Denys Fedoryshchenko <denys@visp.net.lb> Sined-off-by: Eric Dumazet <edumazet@google.com> Cc: Glauber Costa <glommer@parallels.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Horman [Fri, 27 Apr 2012 10:11:49 +0000 (10:11 +0000)]
drop_monitor: Make updating data->skb smp safe
Eric Dumazet pointed out to me that the drop_monitor protocol has some holes in
its smp protections. Specifically, its possible to replace data->skb while its
being written. This patch corrects that by making data->skb an rcu protected
variable. That will prevent it from being overwritten while a tracepoint is
modifying it.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Reported-by: Eric Dumazet <eric.dumazet@gmail.com> CC: David Miller <davem@davemloft.net> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
It stems from holding a spinlock (trace_state_lock) while attempting to register
or unregister tracepoint hooks, making in_atomic() true in this context, leading
to the warning when the tracepoint calls might_sleep() while its taking a mutex.
Since we only use the trace_state_lock to prevent trace protocol state races, as
well as hardware stat list updates on an rcu write side, we can just convert the
spinlock to a mutex to avoid this problem.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Reported-by: Eric Dumazet <eric.dumazet@gmail.com> CC: David Miller <davem@davemloft.net> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
tcp: clean up use of jiffies in tcp_rcv_rtt_measure()
Clean up a reference to jiffies in tcp_rcv_rtt_measure() that should
instead reference tcp_time_stamp. Since the result of the subtraction
is passed into a function taking u32, this should not change any
behavior (and indeed the generated assembly does not change on
x86_64). However, it seems worth cleaning this up for consistency and
clarity (and perhaps to avoid bugs if this is copied and pasted
somewhere else).
Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
flag@flag-desktop:~$ sudo mii-tool eth0
eth0: no link
Tested on my Beagle XM.
v2: added mantainer to the list of recipient
Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Acked-by: Steve Glendinning <steve.glendinning@shawell.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Mahoney [Wed, 25 Apr 2012 14:32:09 +0000 (14:32 +0000)]
dl2k: Clean up rio_ioctl
The dl2k driver's rio_ioctl call has a few issues:
- No permissions checking
- Implements SIOCGMIIREG and SIOCGMIIREG using the SIOCDEVPRIVATE numbers
- Has a few ioctls that may have been used for debugging at one point
but have no place in the kernel proper.
This patch removes all but the MII ioctls, renumbers them to use the
standard ones, and adds the proper permission check for SIOCSMIIREG.
We can also get rid of the dl2k-specific struct mii_data in favor of
the generic struct mii_ioctl_data.
Since we have the phyid on hand, we can add the SIOCGMIIPHY ioctl too.
Most of the MII code for the driver could probably be converted to use
the generic MII library but I don't have a device to test the results.
Reported-by: Stephan Mueller <stephan.mueller@atsec.com> Signed-off-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net>
6lowpan: fix segmentation fault caused by mlme request
Add nescesary mlme callbacks to satisfy "iz list" request from user space.
Due to 6lowpan device doesn't have its own phy, mlme implemented as a pipe
to a real phy to which 6lowpan is attached.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
commit a4910b744486254cfa61995954c118fb2283c4fd has broken promiscuous
mode, which is never set. port->promisc just reflects the last setting
of PROMISCUOUS mode to avoid doing an extra hypercall when it's already
set.
However, since it may fail because of hypervisor permissions, we should
still respect the multicast settings and not simply exit after setting
promiscuous mode.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com> Cc: Breno Leitao <leitao@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
There was a bug in the mask of regtype parameter for registering a
multicast filter. It was ignoring the scope bit, which was wrongly being
used for all filters. The SCOPE_ALL value adds a filter that allows all
multicast packets and ignores the MAC parameter, just what allmulticast
needs. The normals filters, however, should not use SCOPE_ALL.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure net->ipvs is reset on netns cleanup or failed
initialization. It is needed for IPVS applications to know that
IPVS core is not loaded in netns.
Signed-off-by: Julian Anastasov <ja@ssi.bg> Acked-by: Hans Schillstrom <hans.schillstrom@ericsson.com> Signed-off-by: Simon Horman <horms@verge.net.au>
Matt Carlson [Tue, 24 Apr 2012 13:37:01 +0000 (13:37 +0000)]
tg3: Avoid panic from reserved statblk field access
When RSS is enabled, interrupt vector 0 does not receive any rx traffic.
The rx producer index fields for vector 0's status block should be
considered reserved in this case. This patch changes the code to
respect these reserved fields, which avoids a kernel panic when these
fields take on non-zero values.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ipvs: fix crash in ip_vs_control_net_cleanup on unload
commit 14e405461e664b777e2a5636e10b2ebf36a686ec (2.6.39)
("Add __ip_vs_control_{init,cleanup}_sysctl()")
introduced regression due to wrong __net_init for
__ip_vs_control_cleanup_sysctl. This leads to crash when
the ip_vs module is unloaded.
Fix it by changing __net_init to __net_exit for
the function that is already renamed to ip_vs_control_net_cleanup_sysctl.
Signed-off-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: Hans Schillstrom <hans@schillstrom.com> Signed-off-by: Simon Horman <horms@verge.net.au> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
ipvs: Verify that IP_VS protocol has been registered
The registration of a protocol might fail, there were no checks
and all registrations were assumed to be correct. This lead to
NULL ptr dereferences when apps tried registering.
Jeff Kirsher [Fri, 20 Apr 2012 08:51:45 +0000 (08:51 +0000)]
e1000e: Fix default interrupt throttle rate not set in NIC HW
Based on the original patch from Ying Cai <ycai@google.com>
This change ensures that the itr/itr_setting adjustment logic is used,
even for the default/compiled-in value.
Context:
When we changed the default InterruptThrottleRate value from default
(3 = dynamic mode) to 8000 for example, only adapter->itr_setting
(which controls interrupt coalescing mode) was set to 8000, but
adapter->itr (which controls the value set in NIC register) was not
updated accordingly. So from ethtool, it seemed the interrupt
throttling is enabled at 8000 intr/s, but the NIC actually was
running in dynamic mode which has lower CPU efficiency especially
when throughput is not high.
CC: Ying Cai <ycai@google.com> CC: David Decotigny <david.decotigny@google.com> Signed-off-by: Jeff Kirsher <jeffrey.kirsher@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com>
e1000e: MSI interrupt test failed, using legacy interrupt
Following logs where seen on Systems with multiple NICs,
while using MSI interrupts as shown below:
Feb 16 15:09:32 (none) user.notice kernel: 0000:00:0d.0: lan0_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:32 (none) user.notice kernel: 0000:40:0d.0: wan0_1: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:32 (none) user.notice kernel: 0000:40:0d.0: lan0_1: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:32 (none) user.warn kernel: 0000:40:0e.0: wan4_0: MSI interrupt
test failed, using legacy interrupt.
Feb 16 15:09:32 (none) user.notice kernel: 0000:00:0e.0: wan1_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:00:0e.0: lan1_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:00:0f.0: wan2_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:00:0f.0: lan2_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:40:0a.0: wan3_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:40:0a.0: lan3_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:34 (none) user.notice kernel: 0000:40:0e.0: lan4_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:34 (none) user.notice kernel: 0000:40:0f.0: wan5_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:34 (none) user.notice kernel: 0000:40:0f.0: lan5_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
This patch fixes this problem by increasing the msleep from 50 to 100.
Signed-off-by: Prasanna S Panchamukhi <ppanchamukhi@riverbed.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
mac80211: call ieee80211_mgd_stop() on interface stop
ieee80211_mgd_teardown() is called on netdev removal, which
occurs after the vif was already removed from the low-level
driver, resulting in the following warning:
Johannes Berg [Mon, 23 Apr 2012 21:17:50 +0000 (14:17 -0700)]
iwlwifi: fix hardware queue programming
Newer devices have 20 (5000 series) or 30 (6000 series)
hardware queues, rather than the 16 that 4965 had. This
was added to the driver a long time ago, but improperly:
the queue registers for the higher queues aren't just
continuations of the registers for the first 16 queues,
they are in other places. Therefore, the hardware would
lock up when trying to activate queue 16 or above and
the device would have to be restarted.
Thanks goes to Emmanuel who identified this and told me
how the queue programming should be done.
Note that we don't use queues 20 and higher today and
doing so needs more work than this.
Cc: stable@vger.kernel.org Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ingo van Lil [Mon, 23 Apr 2012 22:05:38 +0000 (22:05 +0000)]
asix: Fix tx transfer padding for full-speed USB
The asix.c USB Ethernet driver avoids ending a tx transfer with a zero-
length packet by appending a four-byte padding to transfers whose length
is a multiple of maxpacket. However, the hard-coded 512 byte maxpacket
length is valid for high-speed USB only; full-speed USB uses 64 byte
packets.
Signed-off-by: Ingo van Lil <inguin@gmx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
PHY connect attempts fail if no PHY id is specified in the emac platform
data and another mdio bus has been registered before 'davinci_mdio' bus. In
this case when configuring the interface, there will be an attempt to
connect to already attached PHY on the previously registered mdio bus:
net eth1: PHY already attached
net eth1: could not connect to phy smsc911x-0:01
IP-Config: Failed to open eth1
IP-Config: Device `eth1' not found
Fix this by modifying match_first_device() to match first PHY device
on 'davinci_mdio' bus.
Signed-off-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Raspl [Sun, 22 Apr 2012 21:21:42 +0000 (21:21 +0000)]
qeth: Use blkt defaults for OSA Express 4
The previous blkt defaults for OSA Express 4 cards produced inadequate
performance for streaming workloads. The present patch will apply a
set of more appropriate defaults.
Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com> Reviewed-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
There exist qeth sysfs blkt attributes to change the default blkt
values. But blkt changes are reset during online setting due to a 2nd
invocation of qeth_determine_capabilites(). This patch makes sure
blkt default values are configured during 1st run of
qeth_determine_capabilities() only. Thus blkt changes are kept
during online setting.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Reported-by: Horst Hartmann <horst.hartmann@de.ibm.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
set fake_rtable's dst to NULL to avoid kernel Oops
bridge: set fake_rtable's dst to NULL to avoid kernel Oops
when bridge is deleted before tap/vif device's delete, kernel may
encounter an oops because of NULL reference to fake_rtable's dst.
Set fake_rtable's dst to NULL before sending packets out can solve
this problem.
v4 reformat, change br_drop_fake_rtable(skb) to {}
v3 enrich commit header
v2 introducing new flag DST_FAKE_RTABLE to dst_entry struct.
[ Use "do { } while (0)" for nop br_drop_fake_rtable()
implementation -DaveM ]
Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Peter Huang <peter.huangpeng@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull build system failure fix from Michal Marek:
"This fixes build failure with newer gcc that adds some internal
symbols that end in "__mod_*_device_table", but are not actually the
tables themselves."
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
Fix modpost failures in fedora 17
Merge tag 'md-3.4-fixes' of git://neil.brown.name/md
Pull a few more md bug fixes from NeilBrown:
"2 are tagged for -stable, one being for a fairly serious bug that can
corrupt metadata and make it hard to recovery an array. The other is
for a more recent regression since 3.3"
* tag 'md-3.4-fixes' of git://neil.brown.name/md:
md: fix possible corruption of array metadata on shutdown.
md: don't call ->add_disk unless there is good reason.
DM RAID: Use safe version of rdev_for_each
mm: fix s390 BUG by __set_page_dirty_no_writeback on swap
Mel reports a BUG_ON(slot == NULL) in radix_tree_tag_set() on s390
3.0.13: called from __set_page_dirty_nobuffers() when page_remove_rmap()
tries to transfer dirty flag from s390 storage key to struct page and
radix_tree.
That would be because of reclaim's shrink_page_list() calling
add_to_swap() on this page at the same time: first PageSwapCache is set
(causing page_mapping(page) to appear as &swapper_space), then
page->private set, then tree_lock taken, then page inserted into
radix_tree - so there's an interval before taking the lock when the
radix_tree slot is empty.
We could fix this by moving __add_to_swap_cache()'s spin_lock_irq up
before the SetPageSwapCache. But a better fix is simply to do what's
five years overdue: Ken Chen introduced __set_page_dirty_no_writeback()
(if !PageDirty TestSetPageDirty) for tmpfs to skip all the radix_tree
overhead, and swap is just the same - it ignores the radix_tree tag, and
does not participate in dirty page accounting, so should be using
__set_page_dirty_no_writeback() too.
s390 testing now confirms that this does indeed fix the problem.
Reported-by: Mel Gorman <mgorman@suse.de> Signed-off-by: Hugh Dickins <hughd@google.com> Acked-by: Mel Gorman <mgorman@suse.de> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Rik van Riel <riel@redhat.com> Cc: Ken Chen <kenchen@google.com> Cc: stable@vger.kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
removed the possibility of a 'BUG' when data is written to an array
that has just been switched to read-only, but also introduced the
possibility that the array metadata could be corrupted.
If, when md_notify_reboot gets the mddev lock, the array is
in a state where it is assembled but hasn't been started (as can
happen if the personality module is not available, or in other unusual
situations), then incorrect metadata will be written out making it
impossible to re-assemble the array.
So only call __md_stop_writes() if the array has actually been
activated.
This patch is needed for any stable kernel which has had the above
commit applied.
Cc: stable@vger.kernel.org Reported-by: Christoph Nelles <evilazrael@evilazrael.de> Signed-off-by: NeilBrown <neilb@suse.de>
md/raid5: If there is a spare and a want_replacement device, start replacement.
cause md_check_recovery to call ->add_disk much more often.
Instead of only when the array is degraded, it is now called whenever
md_check_recovery finds anything useful to do, which includes
updating the metadata for clean<->dirty transition.
This causes unnecessary work, and causes info messages from ->add_disk
to be reported much too often.
So refine md_check_recovery to only do any actual recovery checking
(including ->add_disk) if MD_RECOVERY_NEEDED is set.
This fix is suitable for 3.3.y:
Cc: stable@vger.kernel.org Reported-by: Jan Ceuleers <jan.ceuleers@computer.org> Signed-off-by: NeilBrown <neilb@suse.de>
brcmsmac: "INTERMEDIATE but not AMPDU" only when tracing
I keep getting the following messages on the log buffer:
[ 2167.097507] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2281.331305] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2281.332539] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2329.876605] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2329.877354] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2462.280756] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2615.651689] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
From the code comment I understand that this something that can -
and does, quite frequently - happen.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com> Acked-by: Franky Lin<frankyl@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This oops is due to interrupts not being disabled in this particular path.
Reported-by: Dave Airlie <airlied@gmail.com> Tested-by: Dave Airlie <airlied@gmail.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@vger.kernel.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ipw2200: Fix race condition in the command completion acknowledge
Driver incorrectly validates command completion: instead of waiting
for a command to be acknowledged it continues execution. Most of the
time driver gets acknowledge of the command completion in a tasklet
before it executes the next one. But sometimes it sends the next
command before it gets acknowledge for the previous one. In such a
case one of the following error messages appear in the log:
Failed to send SYSTEM_CONFIG: Already sending a command.
Failed to send ASSOCIATE: Already sending a command.
Failed to send TX_POWER: Already sending a command.
After that you need to reload the driver to get it working again.
This bug occurs during roaming (reported by Sam Varshavchik)
https://bugzilla.redhat.com/show_bug.cgi?id=738508
and machine booting (reported by Tom Gundersen and Mads Kiilerich)
https://bugs.archlinux.org/task/28097
https://bugzilla.redhat.com/show_bug.cgi?id=802106
This patch doesn't fix the delay issue during firmware load.
But at least device now works as usual after boot.
Cc: stable@kernel.org Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ctx->vif is dereferenced in different part of iwlwifi code, so do not
nullify it.
This should address at least one of the possible reasons of WARNING at
iwlagn_mac_remove_interface, and perhaps some random crashes when
firmware reset is performed.
Cc: stable@vger.kernel.org Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 'ath9k_hw_update_regulatory_maxpower'
helper function has been introduced by
commit a55f858852e4345d0a31af593c46738ca8614bff
(ath9k_hw: Cleanup TX power calculation for AR9287).
Updating of the max_power_level value has been moved
into the helper function in that change, however the
removed code from 'ath9k_hw_ar9287_set_txpower' has
not been replaced with a call of the new helper
function.
Due to that missing call, retrieving tx power for 2x2
and 3x3 chainmask is not handled properly. During the
calculation of the tx power for 2x2 and 3x3 chainmasks
the values are reduced. Those reductions must be
compensated during retrieving.
Fix this by adding the missing call of the helper
function.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Acked-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k: add an extra boolean parameter to ath9k_hw_apply_txpower
In order to unifying regulatory limit handling
commit ca2c68cc7bc80fc4504fb420df04cce99c9ee6ec
(ath9k_hw: clean up tx power handling) introduced
a new helper function 'ath9k_hw_apply_txpower',
and the direct calls of 'ah->eep_ops->set_txpower'
has been replaced by a call of the helper function.
This caused a change in the behaviour of the
'ath9k_hw_set_txpowerlimit' function. The purpose
of that function is to calculate and store the
rate txpower table and the regulatory limit without
touching the hardware registers. Before the commit,
the 'test' parameter of the function was passed to
the 'ah->eep_ops->set_txpower'. Now the calling of
the 'set_txpower' function happens indirectly through
'ath9k_hw_apply_txpower', so the 'test' argument of
the 'set_txpower' is always 'false'.
This patch restores the original behaviour of
'ath9k_hw_set_txpowerlimit' by adding a new
argument to 'ath9k_hw_apply_txpower.'
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Acked-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge branch 'fixes' of git://git.linaro.org/people/rmk/linux-arm
Pull ARM fixes from Russell King:
"Here's my usual Sunday push, just for one revert which PeterZ hollered
about after last weeks push. Other than that, all seems strangely
quiet as far as fixes go in non-platform ARM land at the moment."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
Revert "ARM: 7359/2: smp_twd: Only wait for reprogramming on active cpus"
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc fixes from Benjamin Herrenschmidt:
"Here are a few fixes for powerpc. Note the addition to the generic
irq.h. This is part of a 3-patches regression fix for mpic due to
changes in how IRQ_TYPE_NONE is being handled. Thomas agreed to the
addition of the new IRQ_TYPE_DEFAULT contant, however he hasn't
replied with an Ack to the actual patch yet. I don't to wait much
longer with these patches tho."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/mpic: Properly set default triggers
irq: Add IRQ_TYPE_DEFAULT for use by PIC drivers
powerpc/mpic: Fix confusion between hw_irq and virq
powerpc/pmac: Don't add_timer() twice
powerpc/eeh: Fix crash caused by null eeh_dev
powerpc/mpc85xx: add MPIC message dts node
powerpc/mpic_msgr: fix offset error when setting mer register
powerpc/mpic_msgr: add lock for MPIC message global variable
powerpc/mpic_msgr: fix compile error when SMP disabled
powerpc: fix build when CONFIG_BOOKE_WDT is enabled
powerpc/85xx: don't call of_platform_bus_probe() twice
1) Fix namespace init and cleanup in phonet to fix some oopses, from
Eric W. Biederman.
2) Missing kfree_skb() in AF_KEY, from Julia Lawall.
3) Refcount leak and source address handling fix in l2tp from James
Chapman.
4) Memory leak fix in CAIF from Tomasz Gregorek.
5) When routes are cloned from ipv6 addrconf routes, we don't process
expirations properly. Fix from Gao Feng.
6) Fix panic on DMA errors in atl1 driver, from Tony Zelenoff.
7) Only enable interrupts in 8139cp driver after we've registered the
IRQ handler. From Jason Wang.
8) Fix too many reads of KS_CIDER register in ks8851 during probe,
fixing crashes on spurious interrupts. From Matt Renzelmann.
9) Missing include in ath5k driver and missing iounmap on probe
failure, from Jonathan Bither.
10) Fix RX packet handling in smsc911x driver, from Will Deacon.
11) Fix ixgbe WoL on fiber by leaving the laser on during shutdown.
12) ks8851 needs MAX_RECV_FRAMES increased otherwise the internal MAC
buffers are easily overflown. Fix from Davide Cimingahi.
13) Fix memory leaks in peak_usb CAN driver, from Jesper Juhl.
14) gred packet scheduler can dump in WRED more when doing a netlink
dump. Fix from David Ward.
15) Fix MTU in USB smsc75xx driver, from Stephane Fillod.
16) Dummy device needs ->ndo_uninit handler to properly handle
->ndo_init failures. From Hiroaki SHIMODA.
17) Fix TX fragmentation in ath9k driver, from Sujith Manoharan.
18) Missing RTNL lock in ixgbe PM resume, from Benjamin Poirier.
19) Missing iounmap in farsync WAN driver, from Julia Lawall.
20) With LRO/GRO, tcp_grow_window() is easily tricked into not growing
the receive window properly, and this hurts performance. Fix from
Eric Dumazet.
21) Network namespace init failure can leak net_generic data, fix from
Julian Anastasov.
22) Fix skb_over_panic due to mis-accounting in TCP for partially ACK'd
SKBs. From Eric Dumazet.
23) New IDs for qmi_wwan driver, from Bjørn Mork.
24) Fix races in ax25_exit(), from Eric W. Biederman.
25) IPV6 TCP doesn't handle TCP_MAXSEG socket option properly, copy over
logic from the IPV4 side. From Neal Cardwell.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (59 commits)
tcp: fix TCP_MAXSEG for established IPv6 passive sockets
drivers/net: Do not free an IRQ if its request failed
drop_monitor: allow more events per second
ks8851: Fix request_irq/free_irq mismatch
net/hyperv: Adding cancellation to ensure rndis filter is closed
ks8851: Fix mutex deadlock in ks8851_net_stop()
net ax25: Reorder ax25_exit to remove races.
icplus: fix interrupt for IC+ 101A/G and 1001LF
net: qmi_wwan: support Sierra Wireless MC77xx devices in QMI mode
bnx2x: off by one in bnx2x_ets_e3b0_sp_pri_to_cos_set()
ksz884x: don't copy too much in netdev_set_mac_address()
tcp: fix retransmit of partially acked frames
netns: do not leak net_generic data on failed init
net/sock.h: fix sk_peek_off kernel-doc warning
tcp: fix tcp_grow_window() for large incoming frames
drivers/net/wan/farsync.c: add missing iounmap
davinci_mdio: Fix MDIO timeout check
ipv6: clean up rt6_clean_expires
ipv6: fix rt6_update_expires
arcnet: rimi: Fix device name in debug output
...
This gets rid of the unused default senses array, and replaces the
incorrect use of IRQ_TYPE_NONE with the new IRQ_TYPE_DEFAULT for
the initial set_trigger() call when mapping an interrupt.
This in turn makes us read the HW state and update the irq desc
accordingly.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is meant typically to allow a PIC driver's irq domain map() callback
to establish sane defaults for the interrupt (and make sure that the HW
and the irq_desc are in sync as far as the trigger is concerned).
The irq core may not call the set_trigger callback if it thinks the
trigger is already set to the right setting, so we need to ensure new
descriptors are properly synchronized with the hardware.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc/mpic: Fix confusion between hw_irq and virq
mpic_is_ipi() takes a virq and immediately converts it to a hw_irq.
However, one of the two call sites calls it with a ... hw_irq. The
other call site also happens to have the hw_irq at hand, so let's
change it to just take that as an argument. Also change mpic_is_tm()
for consistency.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If the interrupt and the timeout happen roughly at the same
time, we can get into a situation where the timer function
is run while the interrupt has already been processed. In
this case, the timer function might end up doing an add_timer
on an already pending timer, causing a BUG_ON() to trigger.
Instead, just skip the whole timeout operation if we see that
the timer is pending. The spinlock ensures that the only way
that happens is if we already started a new operation and thus
the timeout can be ignored.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The problem was reported by Anton Blanchard. While EEH error
happened to the PCI device without the corresponding device
driver, kernel crash was seen. Eventually, I successfully
reproduced the problem on Firebird-L machine with utility
"errinjct". Initially, the device driver for Emulex ethernet
MAC has been disabled from .config and force data parity on
the Emulex ethernet MAC with help of "errinjct". Eventually,
I saw the kernel crash after issueing couple of "lspci -v"
command.
The root cause behind is that the PCI device, including the
reference to the corresponding eeh device, will be removed
from the system while EEH does recovery. Afterwards, the
PCI device will be probed again and added into the system
accordingly. So it's not safe to retrieve the eeh device from
the corresponding PCI device after the PCI device has been removed
and not added again.
The patch fixes the issue and retrieve the eeh device from OF node
instead of PCI device after the PCI device has been removed.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com> Tested-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
tcp: fix TCP_MAXSEG for established IPv6 passive sockets
Commit f5fff5d forgot to fix TCP_MAXSEG behavior IPv6 sockets, so IPv6
TCP server sockets that used TCP_MAXSEG would find that the advmss of
child sockets would be incorrect. This commit mirrors the advmss logic
from tcp_v4_syn_recv_sock in tcp_v6_syn_recv_sock. Eventually this
logic should probably be shared between IPv4 and IPv6, but this at
least fixes this issue.
Signed-off-by: Neal Cardwell <ncardwell@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise cpu_active_mask will not set, which lead to other issue.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com> Signed-off-by: Konrad Eisele <konrad@gaisler.com> Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 19 Apr 2012 07:16:21 +0000 (07:16 +0000)]
drop_monitor: allow more events per second
It seems there is a logic error in trace_drop_common(), since we store
only 64 drops, even if they are from same location.
This fix is a one liner, but we probably need more work to avoid useless
atomic dec/inc
Now I can watch 1 Mpps drops through dropwatch...
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Neil Horman <nhorman@tuxdriver.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge tag 'mmc-fixes-for-3.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC fixes from Chris Ball:
- Build fix for omap_hsmmc with OF against 3.4-rc1.
- Fix CONFIG_MMC_UNSAFE_RESUME semantics regression against 3.3, which
broke hotplug card detection when UNSAFE_RESUME is set.
- Fix a race condition in omap_hsmmc with runtime PM.
- Fix two libertas SDIO-powered-resume regressions.
- Small fixes for discard/sanitize, dw_mmc, cd-gpio and esdhc-imx.
* tag 'mmc-fixes-for-3.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
mmc: core: Do not pre-claim host in suspend
mmc: dw_mmc: prevent NULL dereference for dma_ops
mmc: unbreak sdhci-esdhc-imx on i.MX25
mmc: cd-gpio: Include header to pickup exported symbol prototypes
mmc: sdhci: refine non-removable card checking for card detection
mmc: dw_mmc: Fix switch from DMA to PIO
mmc: remove MMC bus legacy suspend/resume method
mmc: omap_hsmmc: Get rid of of_have_populated_dt() usage
mmc: omap_hsmmc: build fix for CONFIG_OF=y and CONFIG_MMC_OMAP_HS=m
mmc: fixes for eMMC v4.5 sanitize operation
mmc: fixes for eMMC v4.5 discard operation
Merge branch 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- Fixes a regression at DVB core when switching from DVB-S2 to DVB-S on
Kaffeine (Fedora 16 Bugzilla #812895);
- Fixes a mutex unlock at an error condition at drx-k;
- Fix winbond-cir set mode;
- mt9m032: Fix a compilation breakage with some random Kconfig;
- mt9m032: fix two dead locks;
- xc5000: don't require an special firmware (that won't be provided by
the vendor) just because the xtal frequency is different;
- V4L DocBook: fix some typos at multi-plane formats description.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] xc5000: support 32MHz & 31.875MHz xtal using the 41.024.5 firmware
[media] V4L: mt9m032: fix compilation breakage
[media] V4L: DocBook: Fix typos in the multi-plane formats description
[media] V4L: mt9m032: fix two dead-locks
[media] rc-core: set mode for winbond-cir
[media] drxk: Does not unlock mutex if sanity check failed in scu_command()
[media] dvb_frontend: Fix a regression when switching back to DVB-S
Merge tag 'mfd-for-linus-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD fixes from Samuel Ortiz:
"We have 3 build fixes, a OMAP USB host PHY reset fix and the twl6040
conversion to an i2c driver. The latter may not sound like a fix but
the twl6040 MFD driver won't probe without it, triggering an OMAP4
audio regression."
* tag 'mfd-for-linus-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: Fix modular builds of rc5t583 regulator support
mfd: Fix asic3_gpio_to_irq
ARM: OMAP3: USB: Fix the EHCI ULPI PHY reset issue
mfd: Convert twl6040 to i2c driver, and separate it from twl core
mfd : Fix dbx500 compilation error
Wenqi Ma [Thu, 19 Apr 2012 00:39:37 +0000 (00:39 +0000)]
net/hyperv: Adding cancellation to ensure rndis filter is closed
Although the network interface is down, the RX packets number which
could be observed by ifconfig may keep on increasing.
This is because the WORK scheduled in netvsc_set_multicast_list()
may be executed after netvsc_close(). That means the rndis filter
may be re-enabled by do_set_multicast() even if it was closed by
netvsc_close().
By canceling possible WORK before close the rndis filter, the issue
could be never happened.
Signed-off-by: Wenqi Ma <wenqi_ma@trendmicro.com.cn> Reviewed-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Boyd [Wed, 18 Apr 2012 17:25:58 +0000 (17:25 +0000)]
ks8851: Fix mutex deadlock in ks8851_net_stop()
There is a potential deadlock scenario when the ks8851 driver
is removed. The interrupt handler schedules a workqueue which
acquires a mutex that ks8851_net_stop() also acquires before
flushing the workqueue. Previously lockdep wouldn't be able
to find this problem but now that it has the support we can
trigger this lockdep warning by rmmoding the driver after
an ifconfig up.
Fix the possible deadlock by disabling the interrupts in
the chip and then release the lock across the workqueue
flushing. The mutex is only there to proect the registers
anyway so this should be ok.
=======================================================
[ INFO: possible circular locking dependency detected ] 3.0.21-00021-g8b33780-dirty #2911
-------------------------------------------------------
rmmod/125 is trying to acquire lock:
((&ks->irq_work)){+.+...}, at: [<c019e0b8>] flush_work+0x0/0xac
but task is already holding lock:
(&ks->lock){+.+...}, at: [<bf00b850>] ks8851_net_stop+0x64/0x138 [ks8851]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
Al Viro [Sat, 21 Apr 2012 01:49:41 +0000 (21:49 -0400)]
aio: don't bother with unmapping when aio_free_ring() is coming from exit_aio()
... since exit_mmap() is coming and it will munmap() everything anyway.
In all other cases aio_free_ring() has ctx->mm == current->mm; moreover,
all other callers of vm_munmap() have mm == current->mm, so this will
allow us to get rid of mm argument of vm_munmap().
Now, dma_ops is assumed that use the IDMAC. But if dma_ops is assigned
the pdata->dma_ops, we didn't ensure that callback function is defined.
If the callback isn't defined, then we should run in PIO mode.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Will Newton <will.newton@imgtec.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Eric Bénard [Wed, 18 Apr 2012 00:30:20 +0000 (02:30 +0200)]
mmc: unbreak sdhci-esdhc-imx on i.MX25
This was broken by me in 37865fe91582582a6f6c00652f6a2b1ff71f8a78
("mmc: sdhci-esdhc-imx: fix timeout on i.MX's sdhci") where more
extensive tests would have shown that read or write of data to the
card were failing (even if the partition table was correctly read).
Signed-off-by: Eric Bénard <eric@eukrea.com> Acked-by: Wolfram Sang <w.sang@pengutronix.de> Cc: stable <stable@vger.kernel.org> Signed-off-by: Chris Ball <cjb@laptop.org>
Daniel Drake [Mon, 9 Apr 2012 23:14:20 +0000 (00:14 +0100)]
mmc: sdhci: refine non-removable card checking for card detection
Commit c79396c191bc19 ("mmc: sdhci: prevent card detection activity
for non-removable cards") disables card detection where the cards
are marked as non-removable.
This makes sense, but the implementation detail of calling
mmc_card_is_removable() causes some problems, because
mmc_card_is_removable() is overloaded with CONFIG_MMC_UNSAFE_RESUME
semantics.
In the OLPC XO case, we need CONFIG_MMC_UNSAFE_RESUME because our root
filesystem is stored on SD, but we also have external SD card slots
where we want automatic card detection.
Refine the check to only apply to hosts marked as MMC_CAP_NONREMOVABLE,
which is defined to mean that the card is *really* nonremovable. This
could be revisited in future if we find a way to improve
CONFIG_MMC_UNSAFE_RESUME semantics.
Signed-off-by: Daniel Drake <dsd@laptop.org> Acked-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
[stable@: please apply to 3.3-stable] Cc: stable <stable@vger.kernel.org> Signed-off-by: Chris Ball <cjb@laptop.org>
When dw_mci_pre_dma_transfer returns failure in some reasons,
dw_mci_submit_data will prepare to switch the PIO mode from DMA.
After switching to PIO mode, DMA(IDMAC in particular) is still
enabled. This makes the corruption in handling interrupt and
the driver lock-up.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> Acked-by: Will Newton <will.newton@imgtec.com> Signed-off-by: Chris Ball <cjb@laptop.org>
MMC bus is using legacy suspend/resume method, which is not compatible if
runtime pm callbacks are used. In this scenario, MMC bus suspend/resume
callbacks cannot be called when system entering S3. So change to use the
new defined dev_pm_ops for system sleeping mode.
Tested on AM335x Platform. Solves major issue/crash reported at
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg65425.html
This continues the theme started with vm_brk() and vm_munmap():
vm_mmap() does the same thing as do_mmap(), but additionally does the
required VM locking.
This uninlines (and rewrites it to be clearer) do_mmap(), which sadly
duplicates it in mm/mmap.c and mm/nommu.c. But that way we don't have
to export our internal do_mmap_pgoff() function.
Some day we hopefully don't have to export do_mmap() either, if all
modular users can become the simpler vm_mmap() instead. We're actually
very close to that already, with the notable exception of the (broken)
use in i810, and a couple of stragglers in binfmt_elf.
projects / mirror_ubuntu-kernels.git / log