Heiko Stuebner [Mon, 21 Aug 2017 15:50:20 +0000 (17:50 +0200)]
arm64: dts: rockchip: add rk3328-rock64 board
The ROCK64 is a credit card size 4K60P HDR Media Board Computer using the
Rockchip RK3328 Quad-Core ARM Cortex A53 64-Bit Processor and supporting
up to 4GB 1600MHz LPDDR3 memory. It provides eMMC module socket, MicroSD
Card slot, Pi-2 Bus, Pi-P5+ Bus, USB 3.0 and many others peripheral
devices interface for makers to integrate with sensors and devices.
The devicetree currently supports basic peripherals, with more to be
added later on.
Joseph Chen [Wed, 9 Aug 2017 02:03:44 +0000 (10:03 +0800)]
arm64: dts: rockchip: add rk805 node for rk3328-evb
RK805 consists of 4 DCDCs, 3 LDOs. It's different from RK808
and RK818 that there are 2 output only GPIOs, we should add
properties "gpio-controller" and "gpio-cells = <2>".
Signed-off-by: Joseph Chen <chenjh@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
William Wu [Thu, 17 Aug 2017 08:24:32 +0000 (16:24 +0800)]
arm64: dts: rockchip: disable tx ipgap linecheck for rk3399 dwc3
RK3399 USB DWC3 controller has a issue that FS/LS devices not
recognized if inserted through USB 3.0 HUB. It's because that
the inter-packet delay between the SSPLIT token to SETUP token
is about 566ns, more then the USB spec requirement.
This patch adds a quirk "snps,dis-tx-ipgap-linecheck-quirk" to
disable the u2mac linestate check to decrease the SSPLIT token
to SETUP token inter-packet delay from 566ns to 466ns.
Signed-off-by: William Wu <william.wu@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Jacob Chen [Thu, 3 Aug 2017 10:32:37 +0000 (18:32 +0800)]
arm64: dts: rockchip: Add support for rk3399 excavator main board
Add support for the rk3399 excavator main board.
This board works in a combination with the sapphire SOM.
This board have been sold as the rk3399 evaluation board for commercial customers.
You can get more info from below link:
http://opensource.rock-chips.com/wiki_Excavator_sapphire_board
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Yakir Yang [Mon, 17 Jul 2017 14:16:57 +0000 (22:16 +0800)]
arm64: dts: rockchip: add rk3399 edp nodes
Add an edp node, and also add edp endpoints to vopb and vopl
output port nodes.
Signed-off-by: Yakir Yang <ykk@rock-chips.com> Signed-off-by: Caesar Wang <wxt@rock-chips.com> Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Mark Yao [Mon, 17 Jul 2017 14:16:55 +0000 (22:16 +0800)]
arm64: dts: rockchip: Add rk3399 vop and display-subsystem
Add devicetree nodes for rk3399 VOP (Video Output Processors), and the
top level display-subsystem root node.
Later patches add endpoints (eDP, HDMI, MIPI, etc) that attach to the
VOPs' output ports.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com> Signed-off-by: Yakir Yang <ykk@rock-chips.com> Signed-off-by: Caesar Wang <wxt@rock-chips.com> Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Caesar Wang [Tue, 25 Jul 2017 09:22:55 +0000 (17:22 +0800)]
arm64: dts: rockchip: update dynamic-power-coefficient for rk3399
This patch updates the dynamic-power-coefficient for big cluster on
rk3399 SoCs.
The dynamic power consumption of the CPU is proportional to the square of
the Voltage (V) and the clock frequency (f). The coefficient is used to
calculate the dynamic power as below -
Pdyn = dynamic-power-coefficient * V^2 * f
Where Voltage is in uV, frequency is in MHz.
As the following is the tested data on rk3399's big cluster.
frequency(MHz) Voltage(V) Current(mA) Dynamic-power-coefficient
24 0.8 15
48 0.8 23 ~417
96 0.8 40 ~443
216 0.8 82 ~438
312 0.8 115 ~430
408 0.8 150 ~455
So the dynamic-power-coefficient average value is about 436.
Signed-off-by: Caesar Wang <wxt@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Caesar Wang [Mon, 17 Jul 2017 08:14:29 +0000 (16:14 +0800)]
arm64: dts: rockchip: add ARM Mali GPU node for RK3399 SoCs
Add Mali GPU device tree node for the RK3399 SoCs, with devfreq
opp table.
RK3399 and RK3399-OP1 SoCs have a different recommendation table with
gpu opp. Also, the ARM's mali driver found on
https://developer.arm.com/products/software/mali-drivers/midgard-kernel.
Signed-off-by: Caesar Wang <wxt@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
William Wu [Fri, 16 Jun 2017 10:34:15 +0000 (18:34 +0800)]
arm64: dts: rockchip: enable usb2 for RK3328 evaluation board
Rockchip's RK3328 evaluation board has one usb2 otg controller
and one usb2 host controller which consist of EHCI and OHCI.
Each usb controller connects with one usb2 phy port through
UTMI+ interface. Let's enable them to support usb2 on RK3328
evaluation board.
Signed-off-by: William Wu <william.wu@rock-chips.com>
[restructured enablement of u2phy subnodes] Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Brian Norris [Fri, 23 Jun 2017 17:07:37 +0000 (10:07 -0700)]
arm64: dts: rockchip: set rk3399 dynamic CPU power coefficients
Provide the dynamic power coefficient of the big and little CPU
clusters. These numbers are currently in use on the Samsung Chromebook
Plus ("Kevin").
The power allocator thermal governor doesn't know how to do anything if
it doesn't get power parameters from its cooling devices (in this case,
CPUfreq). So this effectively enables the power-allocator governor.
Signed-off-by: Brian Norris <briannorris@chromium.org>
[set the property in each core node] Signed-off-by: Heiko Stuebner <heiko@sntech.de>
arm64: dts: rockchip: Use vctrl regulators for dynamic CPU voltages on Gru/Kevin
The Gru device tree currently contains entries for the regulators
ppvar_bigcpu, ppvar_litcpu, ppvar_gpu and ppvar_centerlogic; however,
the regulators have not been enabled, due to the lack of binding and driver
support for keeping the over-voltage protection (OVP) at bay and
preventing unintended regulator shutdowns on voltage downshifts.
Now, the vctrl regulator driver has been merged, along with new bindings
for asymmetric settling time. The driver is OVP aware, it splits larger
voltage decreases in multiple steps when necessary and adds required
delays.
This change renames each of the aforementioned regulators to
<orig_name>_pwm and adds a new vctrl regulator named <orig_name>.
The vctrl regulators use the voltage of their corresponding PWM regulator
as control voltage. The OVP related values are empirical and stem from
the Chrome OS kernel tree.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Signed-off-by: Brian Norris <briannorris@chromium.org>
[fixed node names and parent supplies of gpu and centerlogic] Signed-off-by: Heiko Stuebner <heiko@sntech.de>
arm64: dts: rockchip: Update CPU regulator voltage ranges for Gru
Gru derivatives besides Kevin have slightly different voltage ranges for
their CPU regulators. Let's keep the base Gru file accurate and let
Kevin override.
Merge tag 'standardize-docs' of git://git.lwn.net/linux
Pull documentation format standardization from Jonathan Corbet:
"This series converts a number of top-level documents to the RST format
without incorporating them into the Sphinx tree. The hope is to bring
some uniformity to kernel documentation and, perhaps more importantly,
have our existing docs serve as an example of the desired formatting
for those that will be added later.
Mauro has gone through and fixed up a lot of top-level documentation
files to make them conform to the RST format, but without moving or
renaming them in any way. This will help when we incorporate the ones
we want to keep into the Sphinx doctree, but the real purpose is to
bring a bit of uniformity to our documentation and let the top-level
docs serve as examples for those writing new ones"
* tag 'standardize-docs' of git://git.lwn.net/linux: (84 commits)
docs: kprobes.txt: Fix whitespacing
tee.txt: standardize document format
cgroup-v2.txt: standardize document format
dell_rbu.txt: standardize document format
zorro.txt: standardize document format
xz.txt: standardize document format
xillybus.txt: standardize document format
vfio.txt: standardize document format
vfio-mediated-device.txt: standardize document format
unaligned-memory-access.txt: standardize document format
this_cpu_ops.txt: standardize document format
svga.txt: standardize document format
static-keys.txt: standardize document format
smsc_ece1099.txt: standardize document format
SM501.txt: standardize document format
siphash.txt: standardize document format
sgi-ioc4.txt: standardize document format
SAK.txt: standardize document format
rpmsg.txt: standardize document format
robust-futexes.txt: standardize document format
...
Merge tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull random updates from Ted Ts'o:
"Add wait_for_random_bytes() and get_random_*_wait() functions so that
callers can more safely get random bytes if they can block until the
CRNG is initialized.
Also print a warning if get_random_*() is called before the CRNG is
initialized. By default, only one single-line warning will be printed
per boot. If CONFIG_WARN_ALL_UNSEEDED_RANDOM is defined, then a
warning will be printed for each function which tries to get random
bytes before the CRNG is initialized. This can get spammy for certain
architecture types, so it is not enabled by default"
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
random: reorder READ_ONCE() in get_random_uXX
random: suppress spammy warnings about unseeded randomness
random: warn when kernel uses unseeded randomness
net/route: use get_random_int for random counter
net/neighbor: use get_random_u32 for 32-bit hash random
rhashtable: use get_random_u32 for hash_rnd
ceph: ensure RNG is seeded before using
iscsi: ensure RNG is seeded before use
cifs: use get_random_u32 for 32-bit lock random
random: add get_random_{bytes,u32,u64,int,long,once}_wait family
random: add wait_for_random_bytes() API
Merge branch 'work.mount' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull ->s_options removal from Al Viro:
"Preparations for fsmount/fsopen stuff (coming next cycle). Everything
gets moved to explicit ->show_options(), killing ->s_options off +
some cosmetic bits around fs/namespace.c and friends. Basically, the
stuff needed to work with fsmount series with minimum of conflicts
with other work.
It's not strictly required for this merge window, but it would reduce
the PITA during the coming cycle, so it would be nice to have those
bits and pieces out of the way"
* 'work.mount' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
isofs: Fix isofs_show_options()
VFS: Kill off s_options and helpers
orangefs: Implement show_options
9p: Implement show_options
isofs: Implement show_options
afs: Implement show_options
affs: Implement show_options
befs: Implement show_options
spufs: Implement show_options
bpf: Implement show_options
ramfs: Implement show_options
pstore: Implement show_options
omfs: Implement show_options
hugetlbfs: Implement show_options
VFS: Don't use save/replace_mount_options if not using generic_show_options
VFS: Provide empty name qstr
VFS: Make get_filesystem() return the affected filesystem
VFS: Clean up whitespace in fs/namespace.c and fs/super.c
Provide a function to create a NUL-terminated string from unterminated data
Merge branch 'work.uaccess-unaligned' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull uacess-unaligned removal from Al Viro:
"That stuff had just one user, and an exotic one, at that - binfmt_flat
on arm and m68k"
* 'work.uaccess-unaligned' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
kill {__,}{get,put}_user_unaligned()
binfmt_flat: flat_{get,put}_addr_from_rp() should be able to fail
Merge branch 'misc.compat' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull network field-by-field copy-in updates from Al Viro:
"This part of the misc compat queue was held back for review from
networking folks and since davem has jus ACKed those..."
* 'misc.compat' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
get_compat_bpf_fprog(): don't copyin field-by-field
get_compat_msghdr(): get rid of field-by-field copyin
copy_msghdr_from_user(): get rid of field-by-field copyin
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
"Boston platform support:
- Document DT bindings
- Add CLK driver for board clocks
CM:
- Avoid per-core locking with CM3 & higher
- WARN on attempt to lock invalid VP, not BUG
CPS:
- Select CONFIG_SYS_SUPPORTS_SCHED_SMT for MIPSr6
- Prevent multi-core with dcache aliasing
- Handle cores not powering down more gracefully
- Handle spurious VP starts more gracefully
DSP:
- Add lwx & lhx missaligned access support
eBPF:
- Add MIPS support along with many supporting change to add the
required infrastructure
Generic arch code:
- Misc sysmips MIPS_ATOMIC_SET fixes
- Drop duplicate HAVE_SYSCALL_TRACEPOINTS
- Negate error syscall return in trace
- Correct forced syscall errors
- Traced negative syscalls should return -ENOSYS
- Allow samples/bpf/tracex5 to access syscall arguments for sane
traces
- Cleanup from old Kconfig options in defconfigs
- Fix PREF instruction usage by memcpy for MIPS R6
- Fix various special cases in the FPU eulation
- Fix some special cases in MIPS16e2 support
- Fix MIPS I ISA /proc/cpuinfo reporting
- Sort MIPS Kconfig alphabetically
- Fix minimum alignment requirement of IRQ stack as required by
ABI / GCC
- Fix special cases in the module loader
- Perform post-DMA cache flushes on systems with MAARs
- Probe the I6500 CPU
- Cleanup cmpxchg and add support for 1 and 2 byte operations
- Use queued read/write locks (qrwlock)
- Use queued spinlocks (qspinlock)
- Add CPU shared FTLB feature detection
- Handle tlbex-tlbp race condition
- Allow storing pgd in C0_CONTEXT for MIPSr6
- Use current_cpu_type() in m4kc_tlbp_war()
- Support Boston in the generic kernel
Generic platform:
- yamon-dt: Pull YAMON DT shim code out of SEAD-3 board
- yamon-dt: Support > 256MB of RAM
- yamon-dt: Use serial* rather than uart* aliases
- Abstract FDT fixup application
- Set RTC_ALWAYS_BCD to 0
- Add a MAINTAINERS entry
core kernel:
- qspinlock.c: include linux/prefetch.h
Loongson 3:
- Add support
Perf:
- Add I6500 support
SEAD-3:
- Remove GIC timer from DT
- Set interrupt-parent per-device, not at root node
- Fix GIC interrupt specifiers
SMP:
- Skip IPI setup if we only have a single CPU
VDSO:
- Make comment match reality
- Improvements to time code in VDSO"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (86 commits)
locking/qspinlock: Include linux/prefetch.h
MIPS: Fix MIPS I ISA /proc/cpuinfo reporting
MIPS: Fix minimum alignment requirement of IRQ stack
MIPS: generic: Support MIPS Boston development boards
MIPS: DTS: img: Don't attempt to build-in all .dtb files
clk: boston: Add a driver for MIPS Boston board clocks
dt-bindings: Document img,boston-clock binding
MIPS: Traced negative syscalls should return -ENOSYS
MIPS: Correct forced syscall errors
MIPS: Negate error syscall return in trace
MIPS: Drop duplicate HAVE_SYSCALL_TRACEPOINTS select
MIPS16e2: Provide feature overrides for non-MIPS16 systems
MIPS: MIPS16e2: Report ASE presence in /proc/cpuinfo
MIPS: MIPS16e2: Subdecode extended LWSP/SWSP instructions
MIPS: MIPS16e2: Identify ASE presence
MIPS: VDSO: Fix a mismatch between comment and preprocessor constant
MIPS: VDSO: Add implementation of gettimeofday() fallback
MIPS: VDSO: Add implementation of clock_gettime() fallback
MIPS: VDSO: Fix conversions in do_monotonic()/do_monotonic_coarse()
MIPS: Use current_cpu_type() in m4kc_tlbp_war()
...
Merge branch 'for-linus-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml
Pull UML updates from Richard Weinberger:
"Mostly fixes for UML:
- First round of fixes for PTRACE_GETRESET/SETREGSET
- A printf vs printk cleanup
- Minor improvements"
* 'for-linus-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
um: Correctly check for PTRACE_GETRESET/SETREGSET
um: v2: Use generic NOTES macro
um: Add kerneldoc for userspace_tramp() and start_userspace()
um: Add kerneldoc for segv_handler
um: stub-data.h: remove superfluous include
um: userspace - be more verbose in ptrace set regs error
um: add dummy ioremap and iounmap functions
um: Allow building and running on older hosts
um: Avoid longjmp/setjmp symbol clashes with libpthread.a
um: console: Ignore console= option
um: Use os_warn to print out pre-boot warning/error messages
um: Add os_warn() for pre-boot warning/error messages
um: Use os_info for the messages on normal path
um: Add os_info() for pre-boot information messages
um: Use printk instead of printf in make_uml_dir
Merge tag 'upstream-4.13-rc1' of git://git.infradead.org/linux-ubifs
Pull UBIFS updates from Richard Weinberger:
- Updates and fixes for the file encryption mode
- Minor improvements
- Random fixes
* tag 'upstream-4.13-rc1' of git://git.infradead.org/linux-ubifs:
ubifs: Set double hash cookie also for RENAME_EXCHANGE
ubifs: Massage assert in ubifs_xattr_set() wrt. init_xattrs
ubifs: Don't leak kernel memory to the MTD
ubifs: Change gfp flags in page allocation for bulk read
ubifs: Fix oops when remounting with no_bulk_read.
ubifs: Fail commit if TNC is obviously inconsistent
ubifs: allow userspace to map mounts to volumes
ubifs: Wire-up statx() support
ubifs: Remove dead code from ubifs_get_link()
ubifs: Massage debug prints wrt. fscrypt
ubifs: Add assert to dent_key_init()
ubifs: Fix unlink code wrt. double hash lookups
ubifs: Fix data node size for truncating uncompressed nodes
ubifs: Don't encrypt special files on creation
ubifs: Fix memory leak in RENAME_WHITEOUT error path in do_rename
ubifs: Fix inode data budget in ubifs_mknod
ubifs: Correctly evict xattr inodes
ubifs: Unexport ubifs_inode_slab
ubifs: don't bother checking for encryption key in ->mmap()
ubifs: require key for truncate(2) of encrypted file
Merge tag 'kvm-4.13-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull more KVM updates from Radim Krčmář:
"Second batch of KVM updates for v4.13
Common:
- add uevents for VM creation/destruction
- annotate and properly access RCU-protected objects
s390:
- rename IOCTL added in the first v4.13 merge
x86:
- emulate VMLOAD VMSAVE feature in SVM
- support paravirtual asynchronous page fault while nested
- add Hyper-V userspace interfaces for better migration
- improve master clock corner cases
- extend internal error reporting after EPT misconfig
- correct single-stepping of emulated instructions in SVM
- handle MCE during VM entry
- fix nVMX VM entry checks and nVMX VMCS shadowing"
* tag 'kvm-4.13-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (28 commits)
kvm: x86: hyperv: make VP_INDEX managed by userspace
KVM: async_pf: Let guest support delivery of async_pf from guest mode
KVM: async_pf: Force a nested vmexit if the injected #PF is async_pf
KVM: async_pf: Add L1 guest async_pf #PF vmexit handler
KVM: x86: Simplify kvm_x86_ops->queue_exception parameter list
kvm: x86: hyperv: add KVM_CAP_HYPERV_SYNIC2
KVM: x86: make backwards_tsc_observed a per-VM variable
KVM: trigger uevents when creating or destroying a VM
KVM: SVM: Enable Virtual VMLOAD VMSAVE feature
KVM: SVM: Add Virtual VMLOAD VMSAVE feature definition
KVM: SVM: Rename lbr_ctl field in the vmcb control area
KVM: SVM: Prepare for new bit definition in lbr_ctl
KVM: SVM: handle singlestep exception when skipping emulated instructions
KVM: x86: take slots_lock in kvm_free_pit
KVM: s390: Fix KVM_S390_GET_CMMA_BITS ioctl definition
kvm: vmx: Properly handle machine check during VM-entry
KVM: x86: update master clock before computing kvmclock_offset
kvm: nVMX: Shadow "high" parts of shadowed 64-bit VMCS fields
kvm: nVMX: Fix nested_vmx_check_msr_bitmap_controls
kvm: nVMX: Validate the I/O bitmaps on nested VM-entry
...
Avoid the READ_ONCE in commit 4a072c71f49b ("random: silence compiler
warnings and fix race") if we can leave the function after
arch_get_random_XXX().
Cc: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Theodore Ts'o [Thu, 8 Jun 2017 08:16:59 +0000 (04:16 -0400)]
random: suppress spammy warnings about unseeded randomness
Unfortunately, on some models of some architectures getting a fully
seeded CRNG is extremely difficult, and so this can result in dmesg
getting spammed for a surprisingly long time. This is really bad from
a security perspective, and so architecture maintainers really need to
do what they can to get the CRNG seeded sooner after the system is
booted. However, users can't do anything actionble to address this,
and spamming the kernel messages log will only just annoy people.
For developers who want to work on improving this situation,
CONFIG_WARN_UNSEEDED_RANDOM has been renamed to
CONFIG_WARN_ALL_UNSEEDED_RANDOM. By default the kernel will always
print the first use of unseeded randomness. This way, hopefully the
security obsessed will be happy that there is _some_ indication when
the kernel boots there may be a potential issue with that architecture
or subarchitecture. To see all uses of unseeded randomness,
developers can enable CONFIG_WARN_ALL_UNSEEDED_RANDOM.
Merge tag 'xfs-4.13-merge-6' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull XFS fixes from Darrick Wong:
"Largely debugging and regression fixes.
- Add some locking assertions for the _ilock helpers.
- Revert the XFS_QMOPT_NOLOCK patch; after discussion with hch the
online fsck patch that would have needed it has been redesigned and
no longer needs it.
- Fix behavioral regression of SEEK_HOLE/DATA with negative offsets
to match 4.12-era XFS behavior"
* tag 'xfs-4.13-merge-6' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
vfs: in iomap seek_{hole,data}, return -ENXIO for negative offsets
Revert "xfs: grab dquots without taking the ilock"
xfs: assert locking precondition in xfs_readlink_bmap_ilocked
xfs: assert locking precondіtion in xfs_attr_list_int_ilocked
xfs: fixup xfs_attr_get_ilocked
Merge branch 'for-4.13-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"We've identified and fixed a silent corruption (introduced by code in
the first pull), a fixup after the blk_status_t merge and two fixes to
incremental send that Filipe has been hunting for some time"
* 'for-4.13-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
Btrfs: fix unexpected return value of bio_readpage_error
btrfs: btrfs_create_repair_bio never fails, skip error handling
btrfs: cloned bios must not be iterated by bio_for_each_segment_all
Btrfs: fix write corruption due to bio cloning on raid5/6
Btrfs: incremental send, fix invalid memory access
Btrfs: incremental send, fix invalid path for link commands
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull a few more input updates from Dmitry Torokhov:
- multi-touch handling for Xen
- fix for long-standing bug causing crashes in i8042 on boot
- change to gpio_keys to better handle key presses during system state
transition
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: i8042 - fix crash at boot time
Input: gpio_keys - handle the missing key press event in resume phase
Input: xen-kbdfront - add multi-touch support
Merge tag 'devprop-fix-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull device properties framework fix from Rafael Wysocki:
"This fixes a problem with bool properties that could be seen as "true"
when the property was not present at all by adding a special helper
for bool properties with checks for all of the requisute conditions
(Sakari Ailus)"
* tag 'devprop-fix-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
device property: Introduce fwnode_call_bool_op() for ops that return bool
Merge tag 'acpi-fixes-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These fix the return value of an IRQ mapping routine in the ACPI core,
fix an EC driver issue causing abnormal fan behavior after system
resume on some systems and add quirks for ACPI device objects that
need to be treated as "always present" to work around bogus
implementations of the _STA control method.
Specifics:
- Fix the return value of acpi_gsi_to_irq() to make the GSI to IRQ
mapping work on the Mustang (ARM64) platform (Mark Salter).
- Fix an EC driver issue that causes fans to behave abnormally after
system resume on some systems which turns out to be related to
switching over the EC into the polling mode during the noirq stages
of system suspend and resume (Lv Zheng).
- Add quirks for ACPI device objects that need to be treated as
"always present", because their _STA methods are designed to work
around Windows driver bugs and return garbage from our perspective
(Hans de Goede)"
* tag 'acpi-fixes-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / x86: Add KIOX000A accelerometer on GPD win to always_present_ids array
ACPI / x86: Add Dell Venue 11 Pro 7130 touchscreen to always_present_ids
ACPI / x86: Allow matching always_present_id array entries by DMI
Revert "ACPI / EC: Enable event freeze mode..." to fix a regression
ACPI / EC: Drop EC noirq hooks to fix a regression
ACPI / irq: Fix return code of acpi_gsi_to_irq()
Merge tag 'pm-fixes-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix a recently exposed issue in the PCI device wakeup code and
one older problem related to PCI device wakeup that has been reported
recently, modify one more piece of computations in intel_pstate to get
rid of a rounding error, fix a possible race in the schedutil cpufreq
governor, fix the device PM QoS sysfs interface to correctly handle
invalid user input, fix return values of two probe routines in devfreq
drivers and constify an attribute_group structure in devfreq.
Specifics:
- Avoid clearing the PCI PME Enable bit for devices as a result of
config space restoration which confuses AML executed afterward and
causes wakeup events to be lost on some systems (Rafael Wysocki).
- Fix the native PCIe PME interrupts handling in the cases when the
PME IRQ is set up as a system wakeup one so that runtime PM remote
wakeup works as expected after system resume on systems where that
happens (Rafael Wysocki).
- Fix the device PM QoS sysfs interface to handle invalid user input
correctly instead of using an unititialized variable value as the
latency tolerance for the device at hand (Dan Carpenter).
- Get rid of one more rounding error from intel_pstate computations
(Srinivas Pandruvada).
- Fix the schedutil cpufreq governor to prevent it from possibly
accessing unititialized data structures from governor callbacks in
some cases on systems when multiple CPUs share a single cpufreq
policy object (Vikram Mulukutla).
- Fix the return values of probe routines in two devfreq drivers
(Gustavo Silva).
- Constify an attribute_group structure in devfreq (Arvind Yadav)"
* tag 'pm-fixes-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PCI / PM: Fix native PME handling during system suspend/resume
PCI / PM: Restore PME Enable after config space restoration
cpufreq: schedutil: Fix sugov_start() versus sugov_update_shared() race
PM / QoS: return -EINVAL for bogus strings
cpufreq: intel_pstate: Fix ratio setting for min_perf_pct
PM / devfreq: constify attribute_group structures.
PM / devfreq: tegra: fix error return code in tegra_devfreq_probe()
PM / devfreq: rk3399_dmc: fix error return code in rk3399_dmcfreq_probe()
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
kmod: throttle kmod thread limit
kmod: add test driver to stress test the module loader
MAINTAINERS: give kmod some maintainer love
xtensa: use generic fb.h
fault-inject: add /proc/<pid>/fail-nth
fault-inject: simplify access check for fail-nth
fault-inject: make fail-nth read/write interface symmetric
fault-inject: parse as natural 1-based value for fail-nth write interface
fault-inject: automatically detect the number base for fail-nth write interface
kernel/watchdog.c: use better pr_fmt prefix
MAINTAINERS: move the befs tree to kernel.org
lib/atomic64_test.c: add a test that atomic64_inc_not_zero() returns an int
mm: fix overflow check in expand_upwards()
Daniel Micay [Fri, 14 Jul 2017 21:28:12 +0000 (17:28 -0400)]
replace incorrect strscpy use in FORTIFY_SOURCE
Using strscpy was wrong because FORTIFY_SOURCE is passing the maximum
possible size of the outermost object, but strscpy defines the count
parameter as the exact buffer size, so this could copy past the end of
the source. This would still be wrong with the planned usage of
__builtin_object_size(p, 1) for intra-object overflow checks since it's
the maximum possible size of the specified object with no guarantee of
it being that large.
Reuse of the fortified functions like this currently makes the runtime
error reporting less precise but that can be improved later on.
Noticed by Dave Jones and KASAN.
Signed-off-by: Daniel Micay <danielmicay@gmail.com> Acked-by: Kees Cook <keescook@chromium.org> Reported-by: Dave Jones <davej@codemonkey.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull arch/tile updates from Chris Metcalf:
"This adds support for an <arch/intreg.h> to help with removing
__need_xxx #defines from glibc, and removes some dead code in
arch/tile/mm/init.c"
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
mm, tile: drop arch_{add,remove}_memory
tile: prefer <arch/intreg.h> to __need_int_reg_t
Merge tag 'powerpc-4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Nothing that really stands out, just a bunch of fixes that have come
in in the last couple of weeks.
None of these are actually fixes for code that is new in 4.13. It's
roughly half older bugs, with fixes going to stable, and half
fixes/updates for Power9.
Thanks to: Aneesh Kumar K.V, Anton Blanchard, Balbir Singh, Benjamin
Herrenschmidt, Madhavan Srinivasan, Michael Neuling, Nicholas Piggin,
Oliver O'Halloran"
* tag 'powerpc-4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64: Fix atomic64_inc_not_zero() to return an int
powerpc: Fix emulation of mfocrf in emulate_step()
powerpc: Fix emulation of mcrf in emulate_step()
powerpc/perf: Add POWER9 alternate PM_RUN_CYC and PM_RUN_INST_CMPL events
powerpc/perf: Fix SDAR_MODE value for continous sampling on Power9
powerpc/asm: Mark cr0 as clobbered in mftb()
powerpc/powernv: Fix local TLB flush for boot and MCE on POWER9
powerpc/mm/radix: Synchronize updates to the process table
powerpc/mm/radix: Properly clear process table entry
powerpc/powernv: Tell OPAL about our MMU mode on POWER9
powerpc/kexec: Fix radix to hash kexec due to IAMR/AMOR
If we reach the limit of modprobe_limit threads running the next
request_module() call will fail. The original reason for adding a kill
was to do away with possible issues with in old circumstances which would
create a recursive series of request_module() calls.
We can do better than just be super aggressive and reject calls once we've
reached the limit by simply making pending callers wait until the
threshold has been reduced, and then throttling them in, one by one.
This throttling enables requests over the kmod concurrent limit to be
processed once a pending request completes. Only the first item queued up
to wait is woken up. The assumption here is once a task is woken it will
have no other option to also kick the queue to check if there are more
pending tasks -- regardless of whether or not it was successful.
By throttling and processing only max kmod concurrent tasks we ensure we
avoid unexpected fatal request_module() calls, and we keep memory
consumption on module loading to a minimum.
With x86_64 qemu, with 4 cores, 4 GiB of RAM it takes the following run
time to run both tests:
time ./kmod.sh -t 0008
real 0m16.366s
user 0m0.883s
sys 0m8.916s
time ./kmod.sh -t 0009
real 0m50.803s
user 0m0.791s
sys 0m9.852s
Link: http://lkml.kernel.org/r/20170628223155.26472-4-mcgrof@kernel.org Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org> Reviewed-by: Petr Mladek <pmladek@suse.com> Cc: Jessica Yu <jeyu@redhat.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Michal Marek <mmarek@suse.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kmod: add test driver to stress test the module loader
This adds a new stress test driver for kmod: the kernel module loader.
The new stress test driver, test_kmod, is only enabled as a module right
now. It should be possible to load this as built-in and load tests
early (refer to the force_init_test module parameter), however since a
lot of test can get a system out of memory fast we leave this disabled
for now.
Using a system with 1024 MiB of RAM can *easily* get your kernel OOM
fast with this test driver.
The test_kmod driver exposes API knobs for us to fine tune simple
request_module() and get_fs_type() calls. Since these API calls only
allow each one parameter a test driver for these is rather simple.
Other factors that can help out test driver though are the number of
calls we issue and knowing current limitations of each. This exposes
configuration as much as possible through userspace to be able to build
tests directly from userspace.
Since it allows multiple misc devices its will eventually (once we add a
knob to let us create new devices at will) also be possible to perform
more tests in parallel, provided you have enough memory.
We only enable tests we know work as of right now.
0001 - Simple test - 1 thread for empty string
0002 - Simple test - 1 thread for modules/filesystems that do not exist
0003 - Simple test - 1 thread for get_fs_type() only
0004 - Simple test - 2 threads for get_fs_type() only
0005 - multithreaded tests with default setup - request_module() only
0006 - multithreaded tests with default setup - get_fs_type() only
0007 - multithreaded tests with default setup test request_module() and get_fs_type()
0008 - multithreaded - push kmod_concurrent over max_modprobes for request_module()
0009 - multithreaded - push kmod_concurrent over max_modprobes for get_fs_type()
The following test cases currently fail, as such they are not currently
enabled by default:
To be sure to run them as intended please unload both of the modules:
o test_module
o xfs
And ensure they are not loaded on your system prior to testing them. If
you use these paritions for your rootfs you can change the default test
driver used for get_fs_type() by exporting it into your environment. For
example of other test defaults you can override refer to kmod.sh
allow_user_defaults().
Behind the scenes this is how we fine tune at a test case prior to
hitting a trigger to run it:
The kmod.sh script uses the above constructs to build different test cases.
A bit of interpretation of the current failures follows, first two
premises:
a) When request_module() is used userspace figures out an optimized
version of module order for us. Once it finds the modules it needs, as
per depmod symbol dep map, it will finit_module() the respective
modules which are needed for the original request_module() request.
b) We have an optimization in place whereby if a kernel uses
request_module() on a module already loaded we never bother userspace
as the module already is loaded. This is all handled by kernel/kmod.c.
A few things to consider to help identify root causes of issues:
0) kmod 19 has a broken heuristic for modules being assumed to be
built-in to your kernel and will return 0 even though request_module()
failed. Upgrade to a newer version of kmod.
1) A get_fs_type() call for "xfs" will request_module() for "fs-xfs",
not for "xfs". The optimization in kernel described in b) fails to
catch if we have a lot of consecutive get_fs_type() calls. The reason
is the optimization in place does not look for aliases. This means two
consecutive get_fs_type() calls will bump kmod_concurrent, whereas
request_module() will not.
This one explanation why test case 0009 fails at least once for
get_fs_type().
2) If a module fails to load --- for whatever reason (kmod_concurrent
limit reached, file not yet present due to rootfs switch, out of
memory) we have a period of time during which module request for the
same name either with request_module() or get_fs_type() will *also*
fail to load even if the file for the module is ready.
This explains why *multiple* NULLs are possible on test 0009.
3) finit_module() consumes quite a bit of memory.
4) Filesystems typically also have more dependent modules than other
modules, its important to note though that even though a get_fs_type()
call does not incur additional kmod_concurrent bumps, since userspace
loads dependencies it finds it needs via finit_module_fd(), it *will*
take much more memory to load a module with a lot of dependencies.
Because of 3) and 4) we will easily run into out of memory failures with
certain tests. For instance test 0006 fails on qemu with 1024 MiB of RAM.
It panics a box after reaping all userspace processes and still not
having enough memory to reap.
[arnd@arndb.de: add dependencies for test module] Link: http://lkml.kernel.org/r/20170630154834.3689272-1-arnd@arndb.de Link: http://lkml.kernel.org/r/20170628223155.26472-3-mcgrof@kernel.org Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org> Cc: Jessica Yu <jeyu@redhat.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Michal Marek <mmarek@suse.com> Cc: Petr Mladek <pmladek@suse.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The arch uses a verbatim copy of the asm-generic version and does not
add any own implementations to the header, so use asm-generic/fb.h
instead of duplicating code.
Link: http://lkml.kernel.org/r/20170517083545.2115-1-tklauser@distanz.ch Signed-off-by: Tobias Klauser <tklauser@distanz.ch> Acked-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Akinobu Mita [Fri, 14 Jul 2017 21:49:57 +0000 (14:49 -0700)]
fault-inject: simplify access check for fail-nth
The fail-nth file is created with 0666 and the access is permitted if
and only if the task is current.
This file is owned by the currnet user. So we can create it with 0644
and allow the owner to write it. This enables to watch the status of
task->fail_nth from another processes.
Akinobu Mita [Fri, 14 Jul 2017 21:49:54 +0000 (14:49 -0700)]
fault-inject: make fail-nth read/write interface symmetric
The read interface for fail-nth looks a bit odd. Read from this file
returns "NYYYY..." or "YYYYY..." (this makes me surprise when cat this
file). Because there is no EOF condition. The first character
indicates current->fail_nth is zero or not, and then current->fail_nth
is reset to zero.
Just returning task->fail_nth value is more natural to understand.
Akinobu Mita [Fri, 14 Jul 2017 21:49:52 +0000 (14:49 -0700)]
fault-inject: parse as natural 1-based value for fail-nth write interface
The value written to fail-nth file is parsed as 0-based. Parsing as
one-based is more natural to understand and it enables to cancel the
previous setup by simply writing '0'.
This change also converts task->fail_nth from signed to unsigned int.
Kefeng Wang [Fri, 14 Jul 2017 21:49:46 +0000 (14:49 -0700)]
kernel/watchdog.c: use better pr_fmt prefix
After commit 73ce0511c436 ("kernel/watchdog.c: move hardlockup
detector to separate file"), 'NMI watchdog' is inappropriate in
kernel/watchdog.c, using 'watchdog' only.
Michael Ellerman [Fri, 14 Jul 2017 21:49:41 +0000 (14:49 -0700)]
lib/atomic64_test.c: add a test that atomic64_inc_not_zero() returns an int
atomic64_inc_not_zero() returns a "truth value" which in C is
traditionally an int. That means callers are likely to expect the
result will fit in an int.
If an implementation returns a "true" value which does not fit in an
int, then there's a possibility that callers will truncate it when they
store it in an int.
In fact this happened in practice, see commit 966d2b04e070
("percpu-refcount: fix reference leak during percpu-atomic transition").
So add a test that the result fits in an int, even when the input
doesn't. This catches the case where an implementation just passes the
non-zero input value out as the result.
Jörn Engel noticed that the expand_upwards() function might not return
-ENOMEM in case the requested address is (unsigned long)-PAGE_SIZE and
if the architecture didn't defined TASK_SIZE as multiple of PAGE_SIZE.
Affected architectures are arm, frv, m68k, blackfin, h8300 and xtensa
which all define TASK_SIZE as 0xffffffff, but since none of those have
an upwards-growing stack we currently have no actual issue.
Nevertheless let's fix this just in case any of the architectures with
an upward-growing stack (currently parisc, metag and partly ia64) define
TASK_SIZE similar.
Link: http://lkml.kernel.org/r/20170702192452.GA11868@p100.box Fixes: bd726c90b6b8 ("Allow stack to grow up to address space limit") Signed-off-by: Helge Deller <deller@gmx.de> Reported-by: Jörn Engel <joern@purestorage.com> Cc: Hugh Dickins <hughd@google.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When UBIFS prepares data structures which will be written to the MTD it
ensues that their lengths are multiple of 8. Since it uses kmalloc() the
padded bytes are left uninitialized and we leak a few bytes of kernel
memory to the MTD.
To make sure that all bytes are initialized, let's switch to kzalloc().
Kzalloc() is fine in this case because the buffers are not huge and in
the IO path the performance bottleneck is anyway the MTD.
Cc: stable@vger.kernel.org Fixes: 1e51764a3c2a ("UBIFS: add new flash file system") Signed-off-by: Richard Weinberger <richard@nod.at> Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Richard Weinberger <richard@nod.at>
Hyunchul Lee [Wed, 14 Jun 2017 00:31:49 +0000 (09:31 +0900)]
ubifs: Change gfp flags in page allocation for bulk read
In low memory situations, page allocations for bulk read
can kill applications for reclaiming memory, and print an
failure message when allocations are failed.
Because bulk read is just an optimization, we don't have
to do these and can stop page allocations.
Though this siutation happens rarely, add __GFP_NORETRY
to prevent from excessive memory reclaim and killing
applications, and __GFP_WARN to suppress this failure
message.
For this, Use readahead_gfp_mask for gfp flags when
allocating pages.
Signed-off-by: Hyunchul Lee <cheol.lee@lge.com> Signed-off-by: Richard Weinberger <richard@nod.at>
karam.lee [Mon, 12 Jun 2017 01:46:31 +0000 (10:46 +0900)]
ubifs: Fix oops when remounting with no_bulk_read.
When remounting with the no_bulk_read option,
there is a problem accessing the "bulk_read buffer(bu.buf)"
which has already been freed.
If the bulk_read option is enabled,
ubifs_tnc_bulk_read uses the pre-allocated bu.buf.
While bu.buf is being used by ubifs_tnc_bulk_read,
remounting with no_bulk_read frees bu.buf.
So I added code to check the use of "bu.buf" to avoid this situation.
------
I tested as follows(kernel v3.18) :
Use the script to repeat "no_bulk_read <-> bulk_read"
remount.sh
#!/bin/sh
while true do;
mount -o remount,no_bulk_read ${MOUNT_POINT};
sleep 1;
mount -o remount,bulk_read ${MOUNT_POINT};
sleep 1;
done
ubifs: Fail commit if TNC is obviously inconsistent
A reference to LEB 0 or with length 0 in the TNC
is never correct and could be caused by a memory corruption.
Don't write such a bad index node to the MTD.
Instead fail the commit which will turn UBIFS into read-only mode.
This is less painful than having the bad reference on the MTD
from where UBFIS has no chance to recover.
Signed-off-by: Richard Weinberger <richard@nod.at>
Rabin Vincent [Wed, 31 May 2017 09:40:27 +0000 (11:40 +0200)]
ubifs: allow userspace to map mounts to volumes
There currently appears to be no way for userspace to find out the
underlying volume number for a mounted ubifs file system, since ubifs
uses anonymous block devices. The volume name is present in
/proc/mounts but UBI volumes can be renamed after the volume has been
mounted.
To remedy this, show the UBI number and UBI volume number as part of the
options visible under /proc/mounts.
Also, accept and ignore the ubi= vol= options if they are used mounting
(patch from Richard Weinberger).
# mount -t ubifs ubi:baz x
# mount
ubi:baz on /root/x type ubifs (rw,relatime,ubi=0,vol=2)
# ubirename /dev/ubi0 baz bazz
# mount
ubi:baz on /root/x type ubifs (rw,relatime,ubi=0,vol=2)
# ubinfo -d 0 -n 2
Volume ID: 2 (on ubi0)
Type: dynamic
Alignment: 1
Size: 67 LEBs (1063424 bytes, 1.0 MiB)
State: OK
Name: bazz
Character device major/minor: 254:3
Signed-off-by: Rabin Vincent <rabinv@axis.com> Signed-off-by: Richard Weinberger <richard@nod.at>
statx() can report what flags a file has, expose flags that UBIFS
supports. Especially STATX_ATTR_COMPRESSED and STATX_ATTR_ENCRYPTED
can be interesting for userspace.
Signed-off-by: Richard Weinberger <richard@nod.at>
When removing an encrypted file with a long name and without having
the key we have to be able to locate and remove the directory entry
via a double hash. This corner case was simply forgotten.
Fixes: 528e3d178f25 ("ubifs: Add full hash lookup support") Reported-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at> Signed-off-by: Richard Weinberger <richard@nod.at>
ubifs: Fix data node size for truncating uncompressed nodes
Currently, the function truncate_data_node only updates the
destination data node size if compression is used. For
uncompressed nodes, the old length is incorrectly retained.
This patch makes sure that the length is correctly set when
compression is disabled.
Fixes: 7799953b34d1 ("ubifs: Implement encrypt/decrypt for all IO") Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at> Signed-off-by: Richard Weinberger <richard@nod.at>
David Gstir [Wed, 17 May 2017 11:36:16 +0000 (13:36 +0200)]
ubifs: Don't encrypt special files on creation
When a new inode is created, we check if the containing folder has a encryption
policy set and inherit that. This should however only be done for regular
files, links and subdirectories. Not for sockes fifos etc.
Fixes: d475a507457b ("ubifs: Add skeleton for fscrypto") Cc: stable@vger.kernel.org Signed-off-by: David Gstir <david@sigma-star.at> Signed-off-by: Richard Weinberger <richard@nod.at>
projects / mirror_ubuntu-disco-kernel.git / log