Michal Kazior [Wed, 14 May 2014 13:23:31 +0000 (16:23 +0300)]
ath10k: fix handling of wierd MSDU chaining cases
Apparently firmware can sometimes report a
sequence with the first rx descriptor saying it's
not the last MSDU. In that case msdu_chaining
value could be overwritten saying it's not a
chained MSDU. This in turn led to skb_push panic
as the frame could be treated as an A-MSDU instead
of a chained MSDU.
Reported-By: Avery Pennarun <apenwarr@gmail.com> Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Michal Kazior [Wed, 14 May 2014 13:23:31 +0000 (16:23 +0300)]
ath10k: fix htt rx ring clean up
msdu_payId was read before txrx tasklet was killed
so it was possible to end up using an invalid
sk_buff pointer leading to a panic.
Make sure to sanitize rx ring sk_buff pointers and
make the clean up go through all possible entries
and not rely on coherent-DMA mapped u32 index
which could be (in theory) corrupted by the device
as well.
Reported-By: Avery Pennarun <apenwarr@gmail.com> Reported-By: Ben Greear <greearb@candelatech.com> Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Arend van Spriel [Mon, 12 May 2014 08:47:39 +0000 (10:47 +0200)]
brcmfmac: determine chanspec from struct cfg80211_chan_def info
The struct cfg80211_chan_def contains additional info to derive the
bandwidth and side-band information of the chanspec. This patch adds
chandef_to_chanspec() function used in IBSS join and starting AP
operation.
Reviewed-by: Franky Lin <frankyl@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Mon, 12 May 2014 08:47:38 +0000 (10:47 +0200)]
brcmfmac: handle 80MHz chanspecs in construct_reg_info() function
The device is queried about the usability of channels, but it did not
take 80MHz channels into consideration. This patch adds processing those
chanspecs and clear the NO_80MHZ flag for those control/primary channels.
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com> Reviewed-by: Franky Lin <frankyl@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Mon, 12 May 2014 08:47:37 +0000 (10:47 +0200)]
brcmfmac: get rid of brcmf_cfg80211_set_channel() function
The function does not provide any additional functionality and is
used only once so just get rid of it.
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com> Reviewed-by: Franky Lin <frankyl@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Mon, 12 May 2014 08:47:36 +0000 (10:47 +0200)]
brcmfmac: enable 80Mhz in 5G custom regulatory rules
By default allow 80Mhz in custom regulatory rules of the 5G band so
the channels will not be flagged with N0_80MHZ.
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com> Reviewed-by: Franky Lin <frankyl@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Mon, 12 May 2014 08:47:35 +0000 (10:47 +0200)]
brcmfmac: provide VHT capability information to user-space
Although brcmfmac support several 11ac devices it did not advertise
VHT related information to cfg80211.
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com> Reviewed-by: Franky Lin <frankyl@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Mon, 12 May 2014 08:47:34 +0000 (10:47 +0200)]
brcm80211: extend channel conversion functions for 80MHz support
The channel values used by firmware is handled using conversion functions
depending on the type of chip. These functions were already in place but
lacked proper support for 80MHz channel definitions. This patch adds the
support for that.
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com> Reviewed-by: Franky Lin <frankyl@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Mon, 12 May 2014 08:47:33 +0000 (10:47 +0200)]
brcmfmac: remove usage of cfg80211_get_chandef_type()
In the .start_ap callback cfg80211_get_chandef_type() was used to
provide debug log info. However, this causes a warning when the
chandef contains VHT channel with 80MHz bandwidth. Avoid the warning
by just printing the channel and bandwidth instead.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Daniel Kim [Mon, 12 May 2014 08:47:32 +0000 (10:47 +0200)]
brcmfmac: Fix reconnect failure after beacon timeout
The DISASSOC command needs to be sent to firmware when a connection
loss is detected by firmware (e.g., beacon timeout). Otherwise the
next connect request fails due to a lingering LINK(down) event from
firmware. This patch resolves the issue by using brcmf_link_down()
handler, instead of the incomplete duplicated codes.
Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Daniel Kim <dekim@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Mon, 12 May 2014 08:47:31 +0000 (10:47 +0200)]
brcmfmac: enhance nvram processing
The driver serializes the nvram firmware file before sending it
to the device. This patch enhances this to assure serialized data
is properly formatted and provide warnings on syntax failures.
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com> Reviewed-by: Franky Lin <frankyl@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Mon, 12 May 2014 08:47:30 +0000 (10:47 +0200)]
brcmfmac: Make FWS queueing configurable.
FWS is always queuing frames and using a worker for de-queueing,
this is not always efficient for all bus layer. For example SDIO
has an internal queue and worker making the queueing of FWS
unnecessary. Make it possible to bypass the worker if fws mode
is none using a bus interface configuration. For USB bus layer
this configuration is set true to have fws provide queueing
regardless the fws mode.
Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Mon, 12 May 2014 08:47:29 +0000 (10:47 +0200)]
brcmfmac: Move handling 802.1x frames to dhd_linux.
Tracking and handling of 802.1x frames is done in two modules, it
is more logical and clear to move this to dhd_linux module.
Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Mon, 12 May 2014 08:47:28 +0000 (10:47 +0200)]
brcmfmac: Move out hdrpull from tx_finalize.
In tx_finalize the hdrpull is performed. For the new protocol
msgbuf this is complex, because it does not use protocol headers
in front of payload anymore and therefor can not determine interface
index in the hdr pulll operation. Move out the hdrpull operation
from tx_finalize to make msgbuf implementation easier.
Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Daniel Kim [Mon, 12 May 2014 08:47:27 +0000 (10:47 +0200)]
brcmfmac: Report the support of firmware roaming
Currently firmware roaming support is not reported to cfg80211.
This patch reports the support of firmware based roaming when
it is enabled.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Arend Van Spriel <arend@broadcom.com> Signed-off-by: Daniel Kim <dekim@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Daniel Kim [Mon, 12 May 2014 08:47:26 +0000 (10:47 +0200)]
brcmfmac: Give priority to 5GHz band in selecting target BSS
When a BSS provides both 2.4GHz and 5GHz bands, in many cases it
makes sense to choose 5GHz. Typically a 5GHz channel is less crowded
and has less interference and therefore its performance will be
better than a crowded 2.4 GHz channel. This patch configures
'join_pref' to induce firmware to preferably select 5GHz BSS.
Reviewed-by: Arend Van Spriel <arend@broadcom.com> Signed-off-by: Daniel Kim <dekim@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The check of ezusb_firmware_download() return value (added by commit 488ec878034eccb852267b0e27ce9d511f75c587) is broken because
ezusb_firmware_download() returns 1 on success.
This causes the driver not to work with the following error:
orinoco_usb: probe of 3-3:1.0 failed with error -14
Check the return value only for negative values.
This fix should be applied to -stable kernels too.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Thu, 8 May 2014 11:48:38 +0000 (13:48 +0200)]
amend "ath9k: Allow platform override without EEPROM override"
Originally Helmut posted a v2 of the "ath9k: Allow platform override
without EEPROM override", but I had prematurely commited the original
as commit 552a515707a. This commit restores the tree to what Helmut
intended with his v2 submission. -- JWL
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adam Lee [Mon, 5 May 2014 08:33:37 +0000 (16:33 +0800)]
rtlwifi: rtl8188ee: add msi module parameter
The msi module parameter offers an option to enable or disable MSI
interrupts mode. For now, some users report RTL8188EE works only with
MSI on their certain platforms, some others report it works only without
MSI, this parameter will help.
Signed-off-by: Adam Lee <adam.lee@canonical.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
wl1251: only call ieee80211_beacon_loss in managed mode
ieee80211_beacon_loss() is only to be called in managed mode,
but the firmware may send the sync timeout event at any time,
so do a check before calling.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com> Tested-by: Pali Rohár <pali.rohar@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
That commit (or rather, hack) triggers a scary WARN in IBSS (ad-hoc) mode.
Steps to reproduce:
ifconfig wlan0 down
iwconfig wlan0 mode ad-hoc
ifconfig wlan0 up
------------[ cut here ]------------
WARNING: CPU: 0 PID: 905 at kernel/workqueue.c:1400 __queue_work+0x21c/0x2f4()
Modules linked in: wl1251_sdio wl1251 mac80211 cfg80211
CPU: 0 PID: 905 Comm: ifconfig Not tainted 3.15.0-rc2#233
[<c0015f38>] (unwind_backtrace) from [<c0012938>]
[<c0012938>] (show_stack) from [<c05d4034>]
[<c05d4034>] (dump_stack) from [<c0043984>]
[<c0043984>] (warn_slowpath_common) from [<c00439c0>]
[<c00439c0>] (warn_slowpath_null) from [<c005b6c8>]
[<c005b6c8>] (__queue_work) from [<c005b820>]
[<c005b820>] (queue_work_on) from [<bf134ac0>]
[<bf134ac0>] (wl1251_op_config [wl1251])
[<bf099a70>] (ieee80211_hw_config [mac80211])
...
This happens because ieee80211_connection_loss() is not expected to be
called in IBSS mode (mac80211 ends up queuing uninitialized work
in that case).
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com> Tested-by: Pali Rohár <pali.rohar@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmfmac: fallback to mimo_bw_cap for older firmwares
This resulted in disabling 20MHz operation in the firmware.
Reviewed-by: Arend Van Spriel <arend@broadcom.com> Signed-off-by: Daniel Kim <dekim@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eliad Peller [Wed, 26 Feb 2014 12:46:35 +0000 (14:46 +0200)]
mac80211: fix vif name tracing
If sdata doesn't have a valid dev (e.g. in case of monitor
vif), the vif_name field was initialized with (a length of)
some short string, but later was set to a different,
potentially larger one.
This resulted in out-of-bounds write, which usually
appeared as garbage in the trace log.
Simply trace sdata->name, as it should always have the
correct name for both cases.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Fri, 9 May 2014 07:56:53 +0000 (09:56 +0200)]
mac80211: allow VHT with peers not capable of 40MHz
There are two (related) issues with this.
One case, reported by Michal, is related to hostap: it unsets the
20/40 capability bit for stations that associate when it's in 20
MHz mode.
The other case, reported by Eyal, is that some APs like Netgear
R6300v2 and probably others based on the BCM4360 chipset can be
configured for doing VHT at 20Mhz. In this case the beacon has
a VHT IE but the HT cap indicates transmitter only support 20Mhz.
In both of these cases, we currently avoid VHT and use only HT
this means we can't use the highest rates (MCS8), so fixing this
leads to throughput improvements.
Reported-by: Michal Kazior <michal.kazior@tieto.com> Reported-by: Eyal Shapira <eyal@wizery.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Andrea Merello [Wed, 7 May 2014 15:54:46 +0000 (17:54 +0200)]
rtl8187: make CTS-to-self protection work
CTS protection was not working properly because the HW needs
RTS flag to be asserted, and it need also RTS duration field to be
filled with CTS-to-self duration.
This patch makes the driver to do this.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Andrea Merello [Wed, 7 May 2014 15:53:17 +0000 (17:53 +0200)]
rtl8180: make CTS-to-self protection work
CTS protection was not working properly because the HW still need
RTS flag to be asserted, and it need also RTS rate field to be
set with CTS-to-self rate and RTS duration field to be filled with
CTS-to-self duration.
This patch makes the driver to do this.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Wed, 7 May 2014 07:28:31 +0000 (09:28 +0200)]
ath9k: Allow platform override without EEPROM override
Add a new platform data flag "use_eeprom" that indicates that the eeprom
found on the card itself should be used instead of the one present in
the platform data.
This allows to override the MAC address of a PCI card while preserving
the eeprom data from the card itself.
The default behavior is preserved.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Avinash Patil [Wed, 7 May 2014 05:02:45 +0000 (22:02 -0700)]
mwifiex: add HT operation IE in TDLS setup confirm
This patch adds support to populate HT operatation IE in TDLS
setup confirm command. This is required for setting wider
bandwidths for TDLS operations.
Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Avinash Patil [Wed, 7 May 2014 05:02:44 +0000 (22:02 -0700)]
mwifiex: disable TDLS link upon tear down event
This patch adds code to disable TDLS link upon reception of TDLS
teardown event from peer. Teardown event can happen either
because of TDLS teardown packet from peer or internal timeout
configured during TDLS setup. Event is propogated to cfg80211
so that userspace application can take appropriate action.
Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Avinash Patil [Wed, 7 May 2014 05:02:43 +0000 (22:02 -0700)]
mwifiex: configure inactivity timeout for TDLS link
This patch adds configuration timeout for TDLS link. This is
configuered at the time of TDLS link configuration. If TDLS link
is inactive for more than timeout, FW will tear this link.
Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
In case RFKILL is in KILL position, the NIC will issue an
interrupt straight away. This interrupt won't be sent
because it is masked in the hardware.
But if our interrupt service routine is called for another
reason (SHARED_IRQ), then we'll look at the interrupt cause
and service it. This can cause bad things if we are not
ready yet.
Explicitly clean the interrupt cause register to make sure
we won't service anything before we are ready to.
Cc: <stable@vger.kernel.org> [3.14] Reported-and-tested-by: Alexander Monakov <amonakov@gmail.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
iwlwifi: mvm: fix sparse warning when _DEBUGFS isn't set
Since the declaration of iwl_mvm_fw_error_rxf_dump and
iwl_mvm_fw_error_sram_dump is under
ifdef CONFIG_IWLWIFI_DEBUGFS, do the same for their
implementation.
Publish WIPHY_FLAG_HAS_CHANNEL_SWITCH if the fw supports
newly introduced IWL_UCODE_TLV_API_CSA_FLOW.
When CSA starts, save the switching vif inside mvm and during the CSA period
configure fw with a new beacon after each beacon transmission in order to
update the csa counters.
Also, handle correctly the CSA unbind-bind flow which is triggered by mac80211
when the actual channel switch happens.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com> Reviewed-by: Luciano Coelho <luciano.coelho@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Andy Spencer [Fri, 2 May 2014 06:48:13 +0000 (06:48 +0000)]
RTL8192CU: Increase max APFM_ONMAC polling count
With certain hardware combinations the poll interval is exceeded before
initialization completes.
Tested on a MacBookPro10,1 using a Sabrent USB-A11N USB adapter.
Signed-off-by: Andy Spencer <andy753421@ucla.edu> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Greear [Wed, 30 Apr 2014 19:02:05 +0000 (12:02 -0700)]
ath9k: Prevent divide-by-zero upon bad beacon_interval.
A similar patch fixed crashes seen on an ath9k system
when testing against a broken ath10k AP. This patch
is slightly less protective, but probably will do the
job and is less redundant.
Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 24 Apr 2014 07:57:40 +0000 (09:57 +0200)]
iwlwifi: pcie: get rid of q->n_bd
This variable always tracks a constant value (256) so there's
no need to have it. Removing it simplifies code generation,
reducing the .text size (by about 240 bytes on x86-64.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Johannes Berg [Thu, 24 Apr 2014 14:31:08 +0000 (16:31 +0200)]
iwlwifi: make LED support optional
If there's no LED on the system, it doesn't make a lot of sense
to include close to 4k of LED-related code (mostly in mac80211),
so instead of forcing LED support into the kernel, don't build
iwlwifi/mac80211 LED support if there's no LED class support.
Eran Harary [Mon, 28 Apr 2014 12:22:40 +0000 (15:22 +0300)]
iwlwifi: mvm: select the MAC address according to priority
For family 8000 products, the driver should take the MAC
address from the mac_override section and only if this
section is empty it should take it from the HW section.
Signed-off-by: Eran Harary <eran.harary@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Eran Harary [Tue, 25 Mar 2014 12:14:44 +0000 (14:14 +0200)]
iwlwifi: mvm: Prioritize external nvm values on top of the OTP values
Read first the nvm sections from the OTP, then read the nvm
sections from the external file and override the OTP values
(if there were any values in the OTP).
Signed-off-by: Eran Harary <eran.harary@intel.com> Reviewed-by: Dor Shaish <dor.shaish@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Eran Harary [Wed, 23 Apr 2014 07:46:09 +0000 (10:46 +0300)]
iwlwifi: mvm: prevent nic to powered up at driver load
A few devices aren't allowed to be powered up at driver
load time. Add "power_up_nic_in_init" flag to iwl_cfg
structure to customize the load flow according to the
device.
Signed-off-by: Eran Harary <eran.harary@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The expected throughput table used when estimating a new column
depends on the channel bandwidth. When switching from legacy to
siso or mimo the wrong expected throughput table was used as it
was chosen based on the the channel bandwidth in legacy which is
always 20Mhz. Instead it should be chosen based on the current sta
bandwidth which could be also 40Mhz or 80Mhz.
When enabling MCS9 this bug leads to a problem where the max
expected throughput of the siso or mimo column is 0 as MCS9 isn't
supported in 20Mhz. This in turns prevents switching to siso or mimo.
Fix this by using the sta bandwidth when deciding which table to choose.
iwlwifi: mvm: rs: don't allow TPC when power save is disabled
Currently we were checking only if the driver power_scheme is set
to CAM. TPC shouldn't be enabled also when disabling powersave on the
interface (e.g. iw wlan0 set power_save off)
which may occur even if power_scheme wasn't set to CAM.
rs_get_best_rate determines the optimal rate to try in a
new Tx column. Currently we were sometimes trying a too high
rate which would lead us to fail and avoid switching to the
new column despite it having a potential to be better.
Change the logic to try and find the first rate which would
exceed the current actual throughput or be more aggressive
if the success ratio is good.
iwlwifi: mvm: rs: revert changes to search cycle rules
Adding more options in the search cycle causes longer
search cycles with additional wondering off to non optimal Tx
configurations. Reduce the Tx configurations searched to
improve throughput in non optimal attenuations.
cfg80211 is notified about connection failures by
__cfg80211_connect_result() call. However, this
function currently does not free cfg80211 sme.
This results in hanging connection attempts in some cases
e.g. when mac80211 authentication attempt is denied,
we have this function call:
ieee80211_rx_mgmt_auth() -> cfg80211_rx_mlme_mgmt() ->
cfg80211_process_auth() -> cfg80211_sme_rx_auth() ->
__cfg80211_connect_result()
but cfg80211_sme_free() is never get called.
Fixes: ceca7b712 ("cfg80211: separate internal SME implementation") Cc: stable@vger.kernel.org (3.10+) Signed-off-by: Eliad Peller <eliadx.peller@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Henning Rogge [Thu, 1 May 2014 08:03:46 +0000 (10:03 +0200)]
mac80211: Fix mac80211 station info rx bitrate for IBSS mode
Filter out incoming multicast packages before applying their bitrate
to the rx bitrate station info field to prevent them from setting the
rx bitrate to the basic multicast rate.
Signed-off-by: Henning Rogge <hrogge@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ben Hutchings [Sat, 26 Apr 2014 20:59:04 +0000 (21:59 +0100)]
rtl8192cu: Fix unbalanced irq enable in error path of rtl92cu_hw_init()
Fixes: a53268be0cb9 ('rtlwifi: rtl8192cu: Fix too long disable of IRQs') Cc: stable@vger.kernel.org Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is noting wrong with the above commit. The regression occurs because
V0 queue on RTL8192SE cards uses priority 6, not the usual 7. The fix is to
modify the rtl8192se routine that sets the correct transmit queue.
Reported-by: Alex Miller <almiller_1@yahoo.co.uk> Tested-by: Alex Miller <almiller_1@yahoo.co.uk> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@vger.kernel.org> [3.13+] Signed-off-by: John W. Linville <linville@tuxdriver.com>
projects / mirror_ubuntu-kernels.git / log