Bruce Allan [Wed, 5 Dec 2012 06:25:47 +0000 (06:25 +0000)]
e1000e: Acquire/release semaphore when writing each EEPROM page
When data blocks are written to the EEPROM, the HW/SW/FW semaphore must be
held for the duration. With large data blocks on 80003es2lan, 82571 and
82572, this can take too long and cause the firmware to take ownership of
the semaphore and consequently ownership of writes to the EEPROM.
Instead, acquire and release the semaphore for each page of the block
written.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Wed, 5 Dec 2012 06:25:42 +0000 (06:25 +0000)]
e1000e: SerDes autoneg flow control
Enables flow control to be set in SerDes autoneg mode. This is what is
done for copper, but relies on a different set of register/bit checks
since this is all done within the Mac registers.
Remove inapplicable comment in defines.h
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Yuval Mintz [Mon, 14 Jan 2013 05:11:49 +0000 (05:11 +0000)]
bnx2x: Added FW GRO bridging support
Since submit 621b4d6 the bnx2x driver support FW GRO.
However, when using the device with GRO enabled in bridging
scenarios throughput is very low, as the bridge expects all
incoming packets to be passed with CHECKSUM_PARTIAL -
a demand which is satisfied by the SW GRO implementation,
but was missed in the bnx2x driver implementation (which returned
CHECKSUM_UNNECESSARY).
Now, given that the traffic is supported by FW GRO (TCP/IP),
the bnx2x driver calculates the pseudo checksum by itself,
passing skbs with CHECKSUM_PARTIAL and giving a much better
throughput when receiving GRO traffic.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Mon, 14 Jan 2013 05:11:45 +0000 (05:11 +0000)]
bnx2x: Added nvram personalities support
When a device is configured to act as either iscsi or fcoe
device in its nvram, prevent the other from being misused by
preventing its activation in the driver.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yaniv Rosner [Mon, 14 Jan 2013 05:11:44 +0000 (05:11 +0000)]
bnx2x: Fix rare self-test failures
On rare occasions, self test link may fail since the link is
being sampled while it's still being stabilized.
To correct this behaviour, try to sample the link for 2 seconds
prior to declaring a failure.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
TG3_PHY_AUXCTL_SMDSP_ENABLE/DISABLE macros do a blind write to the phy
auxiliary control register and overwrite the EXT_PKT_LEN (bit 14) resulting
in intermittent crc errors on jumbo frames with some link partners. Change
the code to do a read/modify/write.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
tg3: Avoid null pointer dereference in tg3_interrupt in netconsole mode
When netconsole is enabled, logging messages generated during tg3_open
can result in a null pointer dereference for the uninitialized tg3
status block. Use the irq_sync flag to disable polling in the early
stages. irq_sync is cleared when the driver is enabling interrupts after
all initialization is completed.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In commit a5e371f61ad33c07b28e7c9b60c78d71fdd34e2a ("drivers/net: delete
all code/drivers depending on CONFIG_MCA") most of the MCA drivers went,
including the Kconfig/Makefile hooks for ibmlana, but it seems that I
missed the "git rm" on these actual driver files, and with the namespace
overlap with machine check architecture, it got missed by various git
grep type checking done at that time.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Moore [Mon, 14 Jan 2013 07:12:19 +0000 (07:12 +0000)]
tun: fix LSM/SELinux labeling of tun/tap devices
This patch corrects some problems with LSM/SELinux that were introduced
with the multiqueue patchset. The problem stems from the fact that the
multiqueue work changed the relationship between the tun device and its
associated socket; before the socket persisted for the life of the
device, however after the multiqueue changes the socket only persisted
for the life of the userspace connection (fd open). For non-persistent
devices this is not an issue, but for persistent devices this can cause
the tun device to lose its SELinux label.
We correct this problem by adding an opaque LSM security blob to the
tun device struct which allows us to have the LSM security state, e.g.
SELinux labeling information, persist for the lifetime of the tun
device. In the process we tweak the LSM hooks to work with this new
approach to TUN device/socket labeling and introduce a new LSM hook,
security_tun_dev_attach_queue(), to approve requests to attach to a
TUN queue via TUNSETQUEUE.
The SELinux code has been adjusted to match the new LSM hooks, the
other LSMs do not make use of the LSM TUN controls. This patch makes
use of the recently added "tun_socket:attach_queue" permission to
restrict access to the TUNSETQUEUE operation. On older SELinux
policies which do not define the "tun_socket:attach_queue" permission
the access control decision for TUNSETQUEUE will be handled according
to the SELinux policy's unknown permission setting.
Signed-off-by: Paul Moore <pmoore@redhat.com> Acked-by: Eric Paris <eparis@parisplace.org> Tested-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Moore [Mon, 14 Jan 2013 07:12:13 +0000 (07:12 +0000)]
selinux: add the "attach_queue" permission to the "tun_socket" class
Add a new permission to align with the new TUN multiqueue support,
"tun_socket:attach_queue".
The corresponding SELinux reference policy patch is show below:
diff --git a/policy/flask/access_vectors b/policy/flask/access_vectors
index 28802c5..a0664a1 100644
--- a/policy/flask/access_vectors
+++ b/policy/flask/access_vectors
@@ -827,6 +827,9 @@ class kernel_service
class tun_socket
inherits socket
+{
+ attach_queue
+}
class x_pointer
inherits x_device
Signed-off-by: Paul Moore <pmoore@redhat.com> Acked-by: Eric Paris <eparis@parisplace.org> Tested-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 13 Jan 2013 18:21:51 +0000 (18:21 +0000)]
tcp: fix a panic on UP machines in reqsk_fastopen_remove
spin_is_locked() on a non !SMP build is kind of useless.
BUG_ON(!spin_is_locked(xx)) is guaranteed to crash.
Just remove this check in reqsk_fastopen_remove() as
the callers do hold the socket lock.
Reported-by: Ketan Kulkarni <ketkulka@gmail.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jerry Chu <hkchu@google.com> Cc: Yuchung Cheng <ycheng@google.com> Cc: Dave Taht <dave.taht@gmail.com> Acked-by: H.K. Jerry Chu <hkchu@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 14 Jan 2013 21:19:08 +0000 (13:19 -0800)]
Merge tag 'dt-fixes-for-3.8' of git://sources.calxeda.com/kernel/linux
Pull devicetree fixes from Rob Herring:
"Two fixes to prevent unconditional re-compile of dts files on arm and
arm64."
* tag 'dt-fixes-for-3.8' of git://sources.calxeda.com/kernel/linux:
ARM: dts: prevent *.dtb from always being rebuilt
arm64: dts: prevent *.dtb from always being rebuilt
Linus Torvalds [Mon, 14 Jan 2013 21:17:50 +0000 (13:17 -0800)]
vfs: add missing virtual cache flush after editing partial pages
Andrew Morton pointed this out a month ago, and then I completely forgot
about it.
If we read a partial last page of a block device, we will zero out the
end of the page, but since that page can then be mapped into user space,
we should also make sure to flush the cache on architectures that have
virtual caches. We have the flush_dcache_page() function for this, so
use it.
Now, in practice this really never matters, because nobody sane uses
virtual caches to begin with, and they largely exist on old broken RISC
arhitectures.
And even if you did run on one of those obsolete CPU's, the whole "mmap
and access the last partial page of a block device" behavior probably
doesn't actually exist. The normal IO functions (read/write) will never
see the zeroed-out part of the page that migth not be coherent in the
cache, because they honor the size of the device.
So I'm marking this for stable (3.7 only), but I'm not sure anybody will
ever care.
Eric Dumazet [Sun, 13 Jan 2013 07:46:34 +0000 (07:46 +0000)]
ifb: dont hard code inet_net use
ifb should lookup devices in the appropriate namespace.
Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Benjamin LaHaise <bcrl@kvack.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Mon, 14 Jan 2013 00:52:52 +0000 (00:52 +0000)]
net: phy: remove flags argument from phy_{attach, connect, connect_direct}
The flags argument of the phy_{attach,connect,connect_direct} functions
is then used to assign a struct phy_device dev_flags with its value.
All callers but the tg3 driver pass the flag 0, which results in the
underlying PHY drivers in drivers/net/phy/ not being able to actually
use any of the flags they would set in dev_flags. This patch gets rid of
the flags argument, and passes phydev->dev_flags to the internal PHY
library call phy_attach_direct() such that drivers which actually modify
a phy device dev_flags get the value preserved for use by the underlying
phy driver.
Acked-by: Kosta Zertsekel <konszert@marvell.com> Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin LaHaise [Mon, 14 Jan 2013 05:15:39 +0000 (05:15 +0000)]
pkt_sched: namespace aware act_mirred
Eric Dumazet pointed out that act_mirred needs to find the current net_ns,
and struct net pointer is not provided in the call chain. His original
patch made use of current->nsproxy->net_ns to find the network namespace,
but this fails to work correctly for userspace code that makes use of
netlink sockets in different network namespaces. Instead, pass the
"struct net *" down along the call chain to where it is needed.
This version removes the ifb changes as Eric has submitted that patch
separately, but is otherwise identical to the previous version.
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org> Tested-by: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 14 Jan 2013 18:56:05 +0000 (10:56 -0800)]
Merge tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Most of commits found here are for ASoC device specific fixes,
arizona, cs4271, wm5102, wm2200, etc, in addition to a couple of
memory leak fixes in ASoC core.
Other than that, regression fixes in HD-audio and USB-audio, and a fix
for new Realtek codecs."
* tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (30 commits)
ALSA: usb-audio: Fix NULL dereference by access to non-existing substream
ALSA: hda - Add support of new codec ALC284
ALSA: usb-audio: Make ebox44_table static
ALSA: hdspm - Fix wordclock status on AES32
Revert "ALSA: hda - Shut up pins at power-saving mode with Conexnat codecs"
ALSA: hda - Disable runtime D3 for Intel CPT & co
ALSA: pxa27x: fix ac97 warm reset
ALSA: pxa27x: fix ac97 cold reset
ASoC: wm_adsp: Ensure that block writes are from DMA aligned addresses
ASoC: wm2000: Fix sense of speech clarity enable
ASoC: wm5100: Remove DSP B and left justified formats
ASoC: arizona: Remove DSP B and left justified AIF modes
ASoC: wm2200: Remove DSP B and left justified AIF modes
ASoC: wm5102: Improve speaker enable performance
ASoC: core: fix the memory leak in case of remove_aux_dev()
ASoC: core: fix the memory leak in case of device_add() failure
ASoC: cs42l52: Catch no-match case in cs42l52_get_clk
ASoC: lm49453: Update lm49453_reg_defs values as per LM49453 HW revision-B
ASoC: lm49453: Fix adc, mic and sidetone volume ranges
ASoC: arizona: Correct FLL source definitions
...
Paul Gortmaker [Sun, 13 Jan 2013 18:55:05 +0000 (18:55 +0000)]
drivers/net: Clean up orphaned probes in Space.c
The removal of the 8390 EISA drivers actually comprises the
complete content of the EISA probe block, so we can now remove
that block, and its hook into the unified probe. Note that
the deleted comment mentions PCI probes, but they long since
moved elsewhere, so no PCI probes are touched here.
We get rid of the orphaned EISA probe prototypes, and a couple
of left over MCA probe prototypes at the same time.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 14 Jan 2013 17:08:38 +0000 (09:08 -0800)]
Merge tag 'staging-3.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging fixes from Greg Kroah-Hartman:
"Here are a number of small fixes to staging drivers for your 3.8-rc3
tree.
Well, the omapdrm fixes aren't really "small" but they were waiting on
a number of other drm patches to go in through the drm tree, and got
delayed by my vacation over the holidays. They are totally
self-contained, everyone involved have acked them, and they fix issues
that people have been having with the driver.
Other than that one, it's a bunch of tiny bugfixes for a number of
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'staging-3.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (36 commits)
staging: zram: fix invalid memory references during disk write
staging: tidspbridge: use prepare/unprepare on dsp clocks
staging: tidspbridge: Fix build breakage due to splitting CM functions.
staging: comedi: comedi_test: fix race when cancelling command
staging: comedi: Kconfig: COMEDI_NI_AT_A2150 should select COMEDI_FC
staging: comedi: prevent auto-unconfig of manually configured devices
staging: comedi: fix minimum AO period for NI 625x and NI 628x
staging: vme_pio2: fix oops on module unloading
staging: speakup: avoid out-of-range access in synth_add()
staging: speakup: avoid out-of-range access in synth_init()
staging: rtl8192e: Fix failure to check pci_map_single()
staging: rtl8187se: Fix failure to check pci_map_single()
staging: drm/imx: fix double free bug in error path
staging: drm/imx: several bug fixes
staging: drm/imx: check return value of ipu_reset()
staging: drm/omap: fix flags in dma buf exporting
staging: drm/omap: use omapdss low level API
staging/fwserial: Update TODO file per reviewer comments
staging/fwserial: Limit tx/rx to 1394-2008 spec maximum
staging/fwserial: Refine Kconfig help text
...
Linus Torvalds [Mon, 14 Jan 2013 17:07:57 +0000 (09:07 -0800)]
Merge tag 'usb-3.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are a bunch of USB fixes for your 3.8-rc3 tree. They all either
fix problems that have been reported (like the xhci/hub changes) or
add new device ids to existing drivers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (39 commits)
usb: ftdi_sio: Crucible Technologies COMET Caller ID - pid added
usb: host: ohci-tmio: fix compile warning
USB: Add device quirk for Microsoft VX700 webcam
USB: ehci-fsl: fix regression on mpc5121e
usb: chipidea: Allow disabling streaming not only in udc mode
USB: fsl-mph-dr-of: fix regression on mpc5121e
USB: select USB_ARCH_HAS_EHCI for MXS
USB: hub: handle claim of enabled remote wakeup after reset
USB: cdc-acm: Add support for "PSC Scanning, Magellan 800i"
USB: option: add Nexpring NP10T terminal id
USB: option: add Telekom Speedstick LTE II
USB: option: blacklist network interface on ZTE MF880
usb: imx21-hcd: Include missing linux/module.h
USB: option: Add new MEDIATEK PID support
USB: ehci: make debug port in-use detection functional again
USB: usbtest: fix test number in log message
xhci: Avoid "dead ports", add roothub port polling.
USB: Handle warm reset failure on empty port.
USB: Ignore port state until reset completes.
USB: Increase reset timeout.
...
Linus Torvalds [Mon, 14 Jan 2013 17:07:11 +0000 (09:07 -0800)]
Merge tag 'driver-core-3.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg Kroah-Hartman:
"Here are two patches for 3.8-rc3.
One removes the __dev* defines from init.h now that all usages of it
are gone from your tree. The other fix is for debugfs's paramater
that was using the wrong base for the option.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
debugfs: convert gid= argument from decimal, not octal
Remove __dev* markings from init.h
Linus Torvalds [Mon, 14 Jan 2013 17:06:24 +0000 (09:06 -0800)]
Merge tag 'char-misc-3.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc fix from Greg Kroah-Hartman:
"Here is a single fix for the mei driver that resolves a reported
issue.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'char-misc-3.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
mei: fix mismatch in mutex unlock-lock in mei_amthif_read()
Linus Torvalds [Mon, 14 Jan 2013 16:56:31 +0000 (08:56 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Nothing too astounding
- nouveau: bunch of regression fixes and oops fixes
- radeon: UMS fixes, rn50 fix, dma fix
- udl: fix EDID retrieval for large EDIDs."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
udldrmfb: udl_get_edid: drop unneeded i--
udldrmfb: udl_get_edid: usb_control_msg buffer must not be on the stack
udldrmfb: Fix EDID not working with monitors with EDID extension blocks
drm/nvc0/fb: fix crash when different mutex is used to protect same list
drm/nouveau/clock: fix support for more than 2 monitors on nve0
drm/nv50/disp: fix selection of bios script for analog outputs
drm/nv17-50: restore fence buffer on resume
drm/nouveau: fix blank LVDS screen regression on pre-nv50 cards
drm/nouveau: fix nouveau_client allocation failure path
drm/nouveau: don't return freed object from nouveau_handle_create
drm/nouveau/vm: fix memory corruption when pgt allocation fails
drm/nouveau: add locking around instobj list operations
drm/nouveau: do not forcibly power on lvds panels
drm/nouveau/devinit: ensure legacy vga control is enabled during post
radeon/kms: fix dma relocation checking
radeon/kms: force rn50 chip to always report connected on analog output
drm/radeon: fix error path in kpage allocation
drm/radeon: fix a bogus kfree
drm/radeon: fix NULL pointer dereference in UMS mode
1) Fix regression allowing IP_TTL setting of zero, fix from Cong Wang.
2) Fix leak regressions in tunap, from Jason Wang.
3) be2net driver always returns IRQ_HANDLED in INTx handler, fix from
Sathya Perla.
4) qlge doesn't really support NETIF_F_TSO6, don't set that flag. Fix
from Amerigo Wang.
5) Add 802.11ad Atheros wil6210 driver, from Vladimir Kondratiev.
6) Fix MTU calculations in mac80211 layer, from T Krishna Chaitanya.
7) Station info layer of mac80211 needs to use del_timer_sync(), from
Johannes Berg.
8) tcp_read_sock() can loop forever, because we don't immediately stop
when recv_actor() returns zero. Fix from Eric Dumazet.
9) Fix WARN_ON() in tcp_cleanup_rbuf(). We have to use sk_eat_skb() in
tcp_recv_skb() to handle the case where a large GRO packet is split
up while it is use by a splice() operation. Fix also from Eric
Dumazet.
10) addrconf_get_prefix_route() in ipv6 tests flags incorrectly, it
does:
if (X && (p->flags & Y) != 0)
when it really meant to go:
if (X && (p->flags & X) != 0)
fix from Romain Kuntz.
11) Fix lost Kconfig dependency for bfin_mac driver hardware
timestamping. From Lars-Peter Clausen.
12) Fix regression in handling of RST without ACK in TCP, from Eric
Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (37 commits)
be2net: fix unconditionally returning IRQ_HANDLED in INTx
tuntap: fix leaking reference count
tuntap: forbid calling TUNSETIFF when detached
tuntap: switch to use rtnl_dereference()
net, wireless: overwrite default_ethtool_ops
qlge: remove NETIF_F_TSO6 flag
tcp: accept RST without ACK flag
net: ethernet: xilinx: Do not use NO_IRQ in axienet
net: ethernet: xilinx: Do not use axienet on PPC
bnx2x: Allow management traffic after boot from SAN
bnx2x: Fix fastpath structures when memory allocation fails
bfin_mac: Restore hardware time-stamping dependency on BF518
tun: avoid owner checks on IFF_ATTACH_QUEUE
bnx2x: move debugging code before the return
tuntap: refuse to re-attach to different tun_struct
ipv6: use addrconf_get_prefix_route for prefix route lookup [v2]
ipv6: fix the noflags test in addrconf_get_prefix_route
tcp: fix splice() and tcp collapsing interaction
tcp: splice: fix an infinite loop in tcp_read_sock()
net: prevent setting ttl=0 via IP_TTL
...
Stephen Warren [Sat, 29 Dec 2012 00:42:46 +0000 (17:42 -0700)]
ARM: dts: prevent *.dtb from always being rebuilt
if_changed (used by the *.dts->*.dtc rule) rebuilds files if they aren't
contained in $(targets). (make V=2 indicates this). Add $(dtb-y) to
$(targets) to prevent *.dtb from always being rebuilt.
This fixes a regression introduced by the .dtb rule rework in 499cd82
"ARM: dt: change .dtb build rules to build in dts directory".
Reported-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Stephen Warren [Sat, 29 Dec 2012 00:42:47 +0000 (17:42 -0700)]
arm64: dts: prevent *.dtb from always being rebuilt
if_changed (used by the *.dts->*.dtc rule) rebuilds files if they aren't
contained in $(targets). (make V=2 indicates this). Add $(dtb-y) to
$(targets) to prevent *.dtb from always being rebuilt. Note
This fixes a regression introduced by the .dtb rule rework in da4cbc6
"arm64: use new common dtc rule", although since arm64 doesn't actually
have any *.dts yet, this isn't a critical issue.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Nitin Gupta [Wed, 2 Jan 2013 16:53:41 +0000 (08:53 -0800)]
staging: zram: fix invalid memory references during disk write
Fixes a bug introduced by commit c8f2f0db1 ("zram: Fix handling
of incompressible pages") which caused invalid memory references
during disk write. Invalid references could occur in two cases:
- Incoming data expands on compression: In this case, reference was
made to kunmap()'ed bio page.
- Partial (non PAGE_SIZE) write with incompressible data: In this
case, reference was made to a kfree()'ed buffer.
David S. Miller [Mon, 14 Jan 2013 01:36:56 +0000 (20:36 -0500)]
Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge
Included changes:
- use per_cpu_add when possible
- prevent the TT component to add multicast address as "mesh clients"
- some debug output improvements
- proper lockdeps class initializations
- new style fixes (space before/after brackets)
- other minor fixes and refactoring
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6: Introduce ip6_flow_hdr() to fill version, tclass and flowlabel.
This is not only for readability but also for optimization.
What we do here is to build the 32bit word at the beginning of the ipv6
header (the "ip6_flow" virtual member of struct ip6_hdr in RFC3542) and
we do not need to read the tclass portion of the target buffer.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Hans de Goede [Fri, 11 Jan 2013 11:08:57 +0000 (12:08 +0100)]
udldrmfb: udl_get_edid: usb_control_msg buffer must not be on the stack
The buffer passed to usb_control_msg may end up in scatter-gather list, and
may thus not be on the stack. Having it on the stack usually works on x86, but
not on other archs.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
Hans de Goede [Fri, 11 Jan 2013 11:08:56 +0000 (12:08 +0100)]
udldrmfb: Fix EDID not working with monitors with EDID extension blocks
udldrmfb only reads the main EDID block, and if that advertises extensions
the drm_edid code expects them to be present, and starts reading beyond the
buffer udldrmfb passes it.
Although it may be possible to read more EDID info with the udl we simpy don't
know how, and even if trial and error gets it working on one device, that is
no guarantee it will work on other revisions. So this patch does a simple fix
in the form of patching the EDID info to report 0 extension blocks, this
fixes udldrmfb only doing 1024x768 on monitors with EDID extension blocks.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Sun, 13 Jan 2013 22:16:54 +0000 (08:16 +1000)]
Merge branch 'drm-fixes-3.8' of git://people.freedesktop.org/~agd5f/linux into drm-next
Fixes for UMS mode which has been broken for a while plus an rn50 fix
and a dma fix.
* 'drm-fixes-3.8' of git://people.freedesktop.org/~agd5f/linux:
radeon/kms: fix dma relocation checking
radeon/kms: force rn50 chip to always report connected on analog output
drm/radeon: fix error path in kpage allocation
drm/radeon: fix a bogus kfree
drm/radeon: fix NULL pointer dereference in UMS mode
Dave Airlie [Sun, 13 Jan 2013 22:15:36 +0000 (08:15 +1000)]
Merge branch 'drm-nouveau-fixes' of git://anongit.freedesktop.org/git/nouveau/linux-2.6 into drm-next
Regression fixes since rework mostly.
* 'drm-nouveau-fixes' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nvc0/fb: fix crash when different mutex is used to protect same list
drm/nouveau/clock: fix support for more than 2 monitors on nve0
drm/nv50/disp: fix selection of bios script for analog outputs
drm/nv17-50: restore fence buffer on resume
drm/nouveau: fix blank LVDS screen regression on pre-nv50 cards
drm/nouveau: fix nouveau_client allocation failure path
drm/nouveau: don't return freed object from nouveau_handle_create
drm/nouveau/vm: fix memory corruption when pgt allocation fails
drm/nouveau: add locking around instobj list operations
drm/nouveau: do not forcibly power on lvds panels
drm/nouveau/devinit: ensure legacy vga control is enabled during post
usb: ftdi_sio: Crucible Technologies COMET Caller ID - pid added
Simple fix to add support for Crucible Technologies COMET Caller ID
USB decoder - a device containing FTDI USB/Serial converter chip,
handling 1200bps CallerID messages decoded from the phone line -
adding correct USB PID is sufficient.
Tested to apply cleanly and work flawlessly against 3.6.9, 3.7.0-rc8
and 3.8.0-rc3 on both amd64 and x86 arches.
Jan Engelhardt [Thu, 10 Jan 2013 12:30:05 +0000 (12:30 +0000)]
netfilter: x_tables: print correct hook names for ARP
arptables 0.0.4 (released on 10th Jan 2013) supports calling the
CLASSIFY target, but on adding a rule to the wrong chain, the
diagnostic is as follows:
# arptables -A INPUT -j CLASSIFY --set-class 0:0
arptables: Invalid argument
# dmesg | tail -n1
x_tables: arp_tables: CLASSIFY target: used from hooks
PREROUTING, but only usable from INPUT/FORWARD
This is incorrect, since xt_CLASSIFY.c does specify
(1 << NF_ARP_OUT) | (1 << NF_ARP_FORWARD).
This patch corrects the x_tables diagnostic message to print the
proper hook names for the NFPROTO_ARP case.
Affects all kernels down to and including v2.6.31.
Signed-off-by: Jan Engelhardt <jengelh@inai.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Aleksi Torhamo [Wed, 9 Jan 2013 18:08:48 +0000 (20:08 +0200)]
drm/nvc0/fb: fix crash when different mutex is used to protect same list
Fixes regression introduced in commit 861d2107
"drm/nouveau/fb: merge fb/vram and port to subdev interfaces"
nv50_fb_vram_{new,del} functions were changed to use
nouveau_subdev->mutex instead of the old nouveau_mm->mutex.
nvc0_fb_vram_new still uses the nouveau_mm->mutex, but nvc0 doesn't
have its own fb_vram_del function, using nv50_fb_vram_del instead.
Because of this, on nvc0 a different mutex ends up being used to protect
additions and deletions to the same list.
This patch is a -stable candidate for 3.7.
Signed-off-by: Aleksi Torhamo <aleksi@torhamo.net> Reported-by: Roy Spliet <r.spliet@student.tudelft.nl> Tested-by: Roy Spliet <r.spliet@student.tudelft.nl> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Cc: stable@vger.kernel.org
Aleksi Torhamo [Fri, 4 Jan 2013 16:39:13 +0000 (18:39 +0200)]
drm/nouveau/clock: fix support for more than 2 monitors on nve0
Fixes regression introduced in commit 70790f4f
"drm/nouveau/clock: pull in the implementation from all over the place"
When code was moved from nv50_crtc_set_clock to nvc0_clock_pll_set,
the PLLs it is used for got limited to only the first two VPLLs.
nv50_crtc_set_clock was only called to change VPLLs, so it didn't
limit what it was used for in any way. Since nvc0_clock_pll_set is
used for all PLLs, it has to specify which PLLs the code is used for,
and only listed the first two VPLLs.
Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=58735
This patch is a -stable candidate for 3.7.
Signed-off-by: Aleksi Torhamo <aleksi@torhamo.net> Tested-by: Aleksi Torhamo <aleksi@torhamo.net> Tested-by: Sean Santos <quantheory@gmail.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Cc: stable@vger.kernel.org
Marcin Slusarz [Thu, 3 Jan 2013 18:38:45 +0000 (19:38 +0100)]
drm/nv50/disp: fix selection of bios script for analog outputs
Analog output number was overwritten by value from digital output path.
Fix it.
Fixes resume from s2ram: https://bugs.freedesktop.org/show_bug.cgi?id=58729
(as stumbled on by J Binder, Pontus Fuchs and me)
Fixes blank screen on module load (reported by Sune Mølgaard).
Marcin Slusarz [Tue, 25 Dec 2012 17:13:22 +0000 (18:13 +0100)]
drm/nv17-50: restore fence buffer on resume
Since commit 5e120f6e4b3f35b741c5445dfc755f50128c3c44 "drm/nouveau/fence:
convert to exec engine, and improve channel sync" nouveau fence sync
implementation for nv17-50 and nvc0+ started to rely on state of fence buffer
left by previous sync operation. But as pinned bo's (where fence state is
stored) are not saved+restored across suspend/resume, we need to do it
manually.
Marcin Slusarz [Tue, 18 Dec 2012 19:30:47 +0000 (20:30 +0100)]
drm/nouveau: fix blank LVDS screen regression on pre-nv50 cards
Commit 2a44e499 ("drm/nouveau/disp: introduce proper init/fini, separate
from create/destroy") started to call display init routines on pre-nv50
hardware on module load. But LVDS init code sets driver state in a way
which prevents modesetting code from operating properly.
nv04_display_init calls nv04_dfp_restore, which sets encoder->last_dpms to
NV_DPMS_CLEARED.
nv04_lvds_dpms checks last_dpms mode (which is NV_DPMS_CLEARED) and wrongly
assumes it's a "powersaving mode", the new one (DRM_MODE_DPMS_OFF) is too,
so it skips calling some crucial lvds scripts.
Reported-by: Chris Paulson-Ellis <chris@edesix.com> Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Cc: stable@vger.kernel.org
Marcin Slusarz [Mon, 10 Dec 2012 20:30:51 +0000 (21:30 +0100)]
drm/nouveau/vm: fix memory corruption when pgt allocation fails
If we return freed vm, nouveau_drm_open will happily call nouveau_cli_destroy,
which will try to free it again.
Reported-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs [Mon, 10 Dec 2012 08:53:43 +0000 (18:53 +1000)]
drm/nouveau: do not forcibly power on lvds panels
This fix was put in place to fix a bug where the eDP panel on certain
laptops fails to respond over the aux channel after suspend.
It appears that on some systems (Dell M6600, with LVDS panel) there's a
very bad interaction with the eDP init table that causes the SOR to get
very confused and not drive the panel correctly, leading to bleed.
A DPMS off/on cycle is enough to bring it back, but, this will avoid the
problem by not touching the panel GPIOs at times we're not meant to.
Sathya Perla [Fri, 11 Jan 2013 22:47:02 +0000 (22:47 +0000)]
be2net: fix unconditionally returning IRQ_HANDLED in INTx
commit e49cc34f introduced an unconditional IRQ_HANDLED return in be_intx()
to workaround Lancer and BE2 HW issues. This is bad as it prevents the kernel
from detecting interrupt storms due to broken HW.
The BE2/Lancer HW issues are:
1) In Lancer, there is no means for the driver to detect if the interrupt
belonged to device, other than counting and notifying events.
2) In Lancer de-asserting INTx takes a while, causing the INTx irq handler
to be called multiple times till the de-assert happens.
3) In BE2, we see an occasional interrupt even when EQs are unarmed.
Issue (1) can cause the notified events to be orphaned, if NAPI was already
running.
This patch fixes this issue by scheduling NAPI only if it is not scheduled
already. Doing this also takes care of possible events_get() race that may be
caused due to issue (2) and (3). Also, IRQ_HANDLED is returned only the first
time zero events are detected.
(Thanks Ben H. for the feedback and suggestions.)
Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
netfilter: nf_conntrack: fix BUG_ON while removing nf_conntrack with netns
canqun zhang reported that we're hitting BUG_ON in the
nf_conntrack_destroy path when calling kfree_skb while
rmmod'ing the nf_conntrack module.
Currently, the nf_ct_destroy hook is being set to NULL in the
destroy path of conntrack.init_net. However, this is a problem
since init_net may be destroyed before any other existing netns
(we cannot assume any specific ordering while releasing existing
netns according to what I read in recent emails).
Thanks to Gao feng for initial patch to address this issue.
batman-adv: don't compile the BLA switch if not requested
When the Bridge Loop Avoidance component is not compiled-in, its boolean switch
should be not compiled as well. This patch surrounds the switch with a proper
ifdef.
Signed-off-by: Antonio Quartulli <ordex@autistici.org> Acked-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
batman-adv: Initialize lockdep class keys for hashes
Different hashes have the same class key because they get
initialised with the same one. For this reason lockdep can create
false warning when they are used recursively.
Re-initialise the key for each hash after the invocation to hash_new()
to avoid this problem.
Signed-off-by: Antonio Quartulli <ordex@autistici.org> Tested-by: Linus Lüssing <linus.luessing@web.de> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
batman-adv: remove useless assignment in tt_local_add()
The flag field of the tt_local_entry->common structure in
tt_local_add() is first assigned NO_FLAGS and then TT_CLIENT_NEW so
nullifying the first operation. For this reason it is safe to remove
the first assignment.
This was introuduced by ("batman-adv: keep local table consistency for
further TT_RESPONSE")
Signed-off-by: Antonio Quartulli <ordex@autistici.org> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
batman-adv: print the CRC together with the translation tables
To simplify debugging operations, it is better to print the related
CRC together with the translation table (local CRC for the local
table and global CRC for each entry in the global table)
Signed-off-by: Antonio Quartulli <ordex@autistici.org> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
batman-adv: reduce local TT entry timeout to 10 minutes
The current timeout is set to one hour. However a client connected to the mesh
network will always generate traffic. In the worst case it will send ARP
requests every 4 or 5 minutes. On the other hand having a long timeout means
storing dead entries for one hour and it leads to very big trans-tables
containing useless clients.
This patch reduces the timeout to 10 minutes
Signed-off-by: Antonio Quartulli <ordex@autistici.org> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Shan Wei [Tue, 13 Nov 2012 01:53:26 +0000 (09:53 +0800)]
batman-adv: use per_cpu_add helper
this_cpu_add is an atomic operation.
and be more faster than per_cpu_ptr operation.
Signed-off-by: Shan Wei <davidshan@tencent.com> Reviewed-by: Christoph Lameter <cl@linux.com> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de> Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Jason Wang [Fri, 11 Jan 2013 16:59:34 +0000 (16:59 +0000)]
tuntap: fix leaking reference count
Reference count leaking of both module and sock were found:
- When a detached file were closed, its sock refcnt from device were not
released, solving this by add the sock_put().
- The module were hold or drop unconditionally in TUNSETPERSIST, which means we
if we set the persist flag for N times, we need unset it for another N
times. Solving this by only hold or drop an reference when there's a flag
change and also drop the reference count when the persist device is deleted.
Signed-off-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Fri, 11 Jan 2013 16:59:33 +0000 (16:59 +0000)]
tuntap: forbid calling TUNSETIFF when detached
Michael points out that even after Stefan's fix the TUNSETIFF is still allowed
to create a new tap device. This because we only check tfile->tun but the
tfile->detached were introduced. Fix this by failing early in tun_set_iff() if
the file is detached. After this fix, there's no need to do the check again in
tun_set_iff(), so this patch removes it.
Cc: Michael S. Tsirkin <mst@redhat.com> Cc: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Gortmaker [Fri, 11 Jan 2013 14:45:58 +0000 (14:45 +0000)]
networking/cs89x0.txt: delete stale information about hand patching
Output of a git grep happened to make me look into this file, and
I found instructions about how to hand patch (without using patch)
the driver into the kernel tree.
Since the driver has been a part of the mainline kernel for years,
we can dump this whole section. Fortunately it doesn't even cause
a renumbering of the sections to do so.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Felipe Balbi [Thu, 10 Jan 2013 12:32:39 +0000 (14:32 +0200)]
usb: host: ohci-tmio: fix compile warning
Fix the following compile warning:
In file included from drivers/usb/host/ohci-hcd.c:1170:0:
drivers/usb/host/ohci-tmio.c: In function 'tmio_start_hc':
drivers/usb/host/ohci-tmio.c:130:2: warning: format '%llx' expects argument of type 'long long unsigned int', but argument 4 has type 'resource_size_t' [-Wformat]
seen on ARM 32-bit builds.
Signed-off-by: Felipe Balbi <balbi@ti.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fsl-ehci probing fails on mpc5121e:
...
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
fsl-ehci fsl-ehci.0: Could not get controller version
fsl-ehci fsl-ehci.0: can't setup
fsl-ehci fsl-ehci.0: USB bus 1 deregistered
fsl-ehci fsl-ehci.0: init fsl-ehci.0 fail, -22
fsl-ehci: probe of fsl-ehci.0 failed with error -22
Fix it by returning appropriate version info for mpc5121, too.
Maxime Ripard [Fri, 11 Jan 2013 17:06:21 +0000 (18:06 +0100)]
USB: select USB_ARCH_HAS_EHCI for MXS
Commit 09f6ffde (USB: EHCI: fix build error by making ChipIdea host a
normal EHCI driver) introduced a dependency on USB_EHCI_HCD for the
chipidea USB host driver, that in turns depends on USB_ARCH_HAS_EHCI.
If this symbol is not set for MXS, the MXS boards are not able to use
the chipidea driver anymore.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / mirror_ubuntu-eoan-kernel.git / log