Heiko Stuebner [Fri, 30 Nov 2018 10:24:49 +0000 (11:24 +0100)]
drm/rockchip: Add implicit fencing support for planes
Render like lima will attach a fence to the framebuffer dma_buf,
so the display driver should wait for it to finish before showing
the framebufferto prevent tearing.
Generally tested on rk3188, rk3288, rk3328 and rk3399 and
together with an actual lima-based kmscube on rk3188 and rk3328.
Christian König [Fri, 7 Dec 2018 19:10:17 +0000 (20:10 +0100)]
drm/etnaviv: fix for 64bit seqno change
The fence seqno is now 64bit, fixes build warning.
Signed-off-by: Christian König <christian.koenig@amd.com> Acked-by: Lucas Stach <l.stach@pengutronix.de> Acked-by: Alex Deucher <alexander.deucher@amd.com> Link: https://patchwork.freedesktop.org/patch/267136/
Ville Syrjälä [Fri, 28 Sep 2018 18:04:00 +0000 (21:04 +0300)]
drm/dp/mst: Validate REMOTE_I2C_READ harder
Make sure i2c msgs we're asked to transfer conform to the
requirements of REMOTE_I2C_READ. We were only checking that the
last message is a read, but we must also check that the preceding
messages are all writes. Also check that the length of each
message isn't too long.
Ville Syrjälä [Fri, 28 Sep 2018 18:03:59 +0000 (21:03 +0300)]
drm/dp/mst: Configure no_stop_bit correctly for remote i2c xfers
We aren't supposed to force a stop+start between every i2c msg
when performing multi message transfers. This should eg. cause
the DDC segment address to be reset back to 0 between writing
the segment address and reading the actual EDID extension block.
To quote the E-DDC spec:
"... this standard requires that the segment pointer be
reset to 00h when a NO ACK or a STOP condition is received."
Since we're going to touch this might as well consult the
I2C_M_STOP flag to determine whether we want to force the stop
or not.
YueHaibing [Sat, 8 Dec 2018 08:36:25 +0000 (08:36 +0000)]
drm/ast: Remove set but not used variable 'bo'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/ast/ast_fb.c: In function 'astfb_create':
drivers/gpu/drm/ast/ast_fb.c:194:17: warning:
variable 'bo' set but not used [-Wunused-but-set-variable]
It never used since introduction in commit 312fec1405dd ("drm: Initial KMS
driver for AST (ASpeed Technologies) 2000 series (v2)")
Boris Brezillon [Fri, 7 Dec 2018 08:36:06 +0000 (09:36 +0100)]
drm/vc4: Add support for X/Y reflection
Add support for X/Y reflection when the plane is using linear or
T-tiled formats. X/Y reflection hasn't been tested on SAND formats, so
we reject them until proper testing/debugging has been done.
Boris Brezillon [Fri, 7 Dec 2018 08:36:05 +0000 (09:36 +0100)]
drm/vc4: Fix negative X/Y positioning on SAND planes
Commit 3e407417b192 ("drm/vc4: Fix X/Y positioning of planes using
T_TILES modifier") fixed the problem with T_TILES format, but left
things in a non-working state for SAND formats. Address that now.
Eric Anholt [Mon, 3 Dec 2018 22:24:36 +0000 (14:24 -0800)]
drm/v3d: Drop the wait for L2T flush to complete.
According to Dave, once you've started an L2T flush, all L2T accesses
will be blocked until the flush completes. This fixes a consistent
3-4ms stall between the ioctl and running the job, and 3DMMES Taiji
goes from 27fps to 110fps.
v2: Leave a note about why we don't need to wait for completion.
Eric Anholt [Mon, 3 Dec 2018 22:24:35 +0000 (14:24 -0800)]
drm/v3d: Don't bother flushing L1TD at job start.
This is the write combiner for TMU writes. You're supposed to flush
that at job end if you had dirtied any cachelines. Flushing it at job
start then doesn't make any sense.
Mika Kuoppala [Fri, 7 Dec 2018 12:34:28 +0000 (14:34 +0200)]
drm/i915: Compile fix for 64b dma-fence seqno
Many errs of the form:
drivers/gpu/drm/i915/selftests/intel_hangcheck.c: In function ‘__igt_reset_evict_vma’:
./include/linux/kern_levels.h:5:18: error: format ‘%x’ expects argument of type ‘unsigned int’, but argum
Fixes: b312d8ca3a7c ("dma-buf: make fence sequence numbers 64 bit v2") Cc: Christian König <christian.koenig@amd.com> Cc: Chunming Zhou <david1.zhou@amd.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20181207123428.16257-1-mika.kuoppala@linux.intel.com
Christian König [Wed, 14 Nov 2018 15:11:06 +0000 (16:11 +0100)]
dma-buf: make fence sequence numbers 64 bit v2
For a lot of use cases we need 64bit sequence numbers. Currently drivers
overload the dma_fence structure to store the additional bits.
Stop doing that and make the sequence number in the dma_fence always
64bit.
For compatibility with hardware which can do only 32bit sequences the
comparisons in __dma_fence_is_later only takes the lower 32bits as significant
when the upper 32bits are all zero.
Christian König [Wed, 5 Dec 2018 19:43:02 +0000 (20:43 +0100)]
drm/v3d: fix broken build
I missed one case during the recent revert of the replace_fence
interface change.
Fixes: 0b258ed1a219 drm: revert "expand replace_fence to support timeline point v2" Signed-off-by: Christian König <christian.koenig@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Link: https://patchwork.freedesktop.org/patch/266134/
The whole interface isn't thought through. Since this function can't
fail we actually can't allocate an object to store the sync point.
Sorry, I should have taken the lead on this from the very beginning and
reviewed it more thoughtfully. Going to propose a new interface as a
follow up change.
YueHaibing [Sat, 1 Dec 2018 03:20:44 +0000 (03:20 +0000)]
drm/vkms: Remove set but not used variable 'vkms_obj'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/vkms/vkms_plane.c: In function 'vkms_prepare_fb':
drivers/gpu/drm/vkms/vkms_plane.c:144:26: warning:
variable 'vkms_obj' set but not used [-Wunused-but-set-variable]
It never used since introduction in commit 8ce1bb0b5337 ("drm/vkms: map/unmap buffers in [prepare/cleanup]_fb hooks")
Eric Anholt [Sat, 1 Dec 2018 00:57:58 +0000 (16:57 -0800)]
drm/v3d: Add more tracepoints for V3D GPU rendering.
The core scheduler tells us when the job is pushed to the scheduler's
queue, and I had the job_run functions saying when they actually queue
the job to the hardware. By adding tracepoints for the very top of
the ioctls and the IRQs signaling job completion, "perf record -a -e
v3d:.\* -e gpu_scheduler:.\* <job>; perf script" gets you a pretty
decent timeline.
Christian König [Tue, 13 Nov 2018 13:14:00 +0000 (14:14 +0100)]
drm/syncobj: use dma_fence_get_stub
Extract of useful code from the timeline work. Let's use just a single
stub fence instance instead of allocating a new one all the time.
Signed-off-by: Christian König <christian.koenig@amd.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Chunming Zhou <david1.zhou@amd.com> Link: https://patchwork.freedesktop.org/patch/265248/
Christian König [Mon, 3 Dec 2018 12:36:14 +0000 (13:36 +0100)]
dma-buf: add dma_fence_get_stub
Extract of useful code from the timeline work. This provides a function
to return a stub or dummy fence which is always signaled.
Signed-off-by: Christian König <christian.koenig@amd.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Chunming Zhou <david1.zhou@amd.com> Link: https://patchwork.freedesktop.org/patch/265248/
Neil Armstrong [Wed, 28 Nov 2018 10:07:34 +0000 (11:07 +0100)]
drm/meson: Fix an Alpha Primary Plane bug on Meson GXL/GXM SoCs
On the Amlogic GXL & GXM SoCs, a bug occurs on the primary plane when
alpha is used where the alpha is not aligned with the pixel content.
The workaround Amlogic implemented is to reset the OSD1 plane hardware
block each time the plane is (re)enabled, solving the issue.
In the reset, we still need to save the content of 2 registers which
depends on the status of the plane, in addition to reload the scaler
conversion matrix at the same time.
Eric Anholt [Wed, 28 Nov 2018 23:09:27 +0000 (15:09 -0800)]
drm/v3d: Fix prime imports of buffers from other drivers.
v3d_bo_get_pages() checks this to decide to map the imported buffer
instead of the backing shmem file. The caller was about to set this
value anyway, and there's no error path in between. Ideally we
wouldn't even allocate the shmem file for our imports, but that's a
more invasive fix.
Eric Anholt [Wed, 28 Nov 2018 23:09:25 +0000 (15:09 -0800)]
drm/v3d: Add support for submitting jobs to the TFU.
The TFU can copy from raster, UIF, and SAND input images to UIF output
images, with optional mipmap generation. This will certainly be
useful for media EGL image input, but is also useful immediately for
mipmap generation without bogging the V3D core down.
For now we only run the queue 1 job deep, and don't have any hang
recovery (though I don't think we should need it, with TFU). Queuing
multiple jobs in the HW will require synchronizing the YUV coefficient
regs updates since they don't get FIFOed with the job.
v2: Change the ioctl to IOW instead of IOWR, always set COEF0, explain
why TFU is AUTH, clarify the syncing docs, drop the unused TFU
interrupt regs (you're expected to use the hub's), don't take
&bo->base for NULL bos.
v3: Fix a little whitespace alignment (noticed by checkpatch), rebase
on drm_sched_job_cleanup() changes.
Daniel Vetter [Wed, 28 Nov 2018 10:07:28 +0000 (11:07 +0100)]
drm: Fix up drm_atomic_state_helper.[hc] extraction
I've misplaced two functions by accident:
- drm_atomic_helper_duplicate_state is really part of the
resume/suspend/shutdown device-wide helpers.
- drm_atomic_helper_legacy_gamma_set is part of the legacy ioctl
compat helpers.
Sean Paul [Thu, 29 Nov 2018 20:36:48 +0000 (15:36 -0500)]
drm: Fix compiler warning in drm_atomic_helper.c
Kbuild was complaining about:
>> drivers/gpu/drm/drm_atomic_helper.c:3169:27: warning: 'state' may be used uninitialized in this function [-Wmaybe-uninitialized]
Now state can't actually be used uninitialized, but we'll assign a value
anyways so it stops bellyaching.
Kbuild config:
link: https://lists.01.org/pipermail/kbuild-all/2018-November/055374.html
tree: git://anongit.freedesktop.org/drm/drm-misc for-linux-next
head: b7ea04d299c78b6cf96ab281a1683ff62a74f969
commit: b7ea04d299c78b6cf96ab281a1683ff62a74f969 [4/4] drm: Add
DRM_MODESET_LOCK_BEGIN/END helpers
config: x86_64-randconfig-x017-201847 (attached as .config)
compiler: gcc-7 (Debian 7.3.0-1) 7.3.0
reproduce:
git checkout b7ea04d299c78b6cf96ab281a1683ff62a74f969
# save the attached .config to linux build tree
make ARCH=x86_64
Fixes: b7ea04d299c7 ("drm: Add DRM_MODESET_LOCK_BEGIN/END helpers") Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Sean Paul <seanpaul@chromium.org> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Maxime Ripard <maxime.ripard@bootlin.com> Cc: Sean Paul <sean@poorly.run> Cc: David Airlie <airlied@linux.ie> Cc: dri-devel@lists.freedesktop.org Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Sean Paul <seanpaul@chromium.org>
[seanpaul added extra details on airlied's suggestion] Link: https://patchwork.freedesktop.org/patch/msgid/20181129203652.223634-1-sean@poorly.run
Boris Brezillon [Fri, 30 Nov 2018 09:02:53 +0000 (10:02 +0100)]
drm/vc4: Allow scaling on cursor plane
Now that async update has been reworked to allow scaled planes to be
updated asynchronously when the scaling params do not change, we can
remove the NO_SCALING constraint on cursor planes.
Boris Brezillon [Fri, 30 Nov 2018 09:02:52 +0000 (10:02 +0100)]
drm/vc4: Rework the async update logic
vc4_plane_atomic_async_check() was only based on the
state->{crtc,src}_{w,h} which was fine since scaling was not allowed on
the cursor plane.
We are about to change that to properly support underscan, and, in order
to make the async check more reliable, we call vc4_plane_mode_set()
from there and check that only the pos0, pos2 and ptr0 entries in the
dlist have changed.
In vc4_plane_atomic_async_update(), we no longer call
vc4_plane_atomic_check() since vc4_plane_mode_set() has already been
called in vc4_plane_atomic_async_check(), and we don't need to allocate
a new LBM region (we reuse the one from the current state).
Note that we now have to manually update each field of the current
plane state since it's no longer updated in place (not sure we have
to sync all of them, but it's harmless if we do).
We also drop the vc4_plane_async_set_fb() call (ptr0 dlist entry has
been properly updated in vc4_plane_mode_set())
Boris Brezillon [Fri, 30 Nov 2018 09:02:51 +0000 (10:02 +0100)]
drm/vc4: Don't check plane state more than once
We are about to use vc4_plane_mode_set() in the async check path, but
async check can decide that async update is not possible and force the
driver to fallback to a sync update.
All the checks that have been done on the plane state during async check
stay valid, and checking it again is not necessary. Add a ->checked
field to vc4_plane_state, and use it to track the status of the state
(checked or not).
Boris Brezillon [Fri, 30 Nov 2018 09:02:50 +0000 (10:02 +0100)]
drm/vc4: Move LBM creation out of vc4_plane_mode_set()
We are about to use vc4_plane_mode_set() in the async check path, and
async updates require that LBM size stay the same since they reuse the
LBM from the previous state. So we definitely don't want to allocate a
new LBM region that we know for sure will be free right away.
Move the LBM allocation out of vc4_plane_mode_set() and call the new
function (vc4_plane_update_lbm()) from vc4_plane_atomic_check().
Sean Paul [Thu, 29 Nov 2018 15:55:17 +0000 (10:55 -0500)]
Documentation: drm: Remove dangling pointer from drm-mm.rst
Fixes htmldocs build error:
Error: Cannot open file ../drivers/gpu/drm/drm_global.c
Fixes: 2bb42410b1bd ("drm: Remove drm_global.{c,h} v2") Cc: Thomas Zimmermann <tzimmermann@suse.de> Cc: Christian König <christian.koenig@amd.com> Cc: Junwei Zhang <Jerry.Zhang@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Maxime Ripard <maxime.ripard@bootlin.com> Cc: Sean Paul <sean@poorly.run> Cc: David Airlie <airlied@linux.ie> Cc: Christian Koenig <christian.koenig@amd.com> Cc: Huang Rui <ray.huang@amd.com> Cc: dri-devel@lists.freedesktop.org Signed-off-by: Sean Paul <seanpaul@chromium.org> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181129155522.33749-1-sean@poorly.run
Sean Paul [Thu, 29 Nov 2018 15:04:17 +0000 (10:04 -0500)]
drm: Add DRM_MODESET_LOCK_BEGIN/END helpers
This patch adds a couple of helpers to remove the boilerplate involved
in grabbing all of the modeset locks.
I've also converted the obvious cases in drm core to use the helpers.
The only remaining instance of drm_modeset_lock_all_ctx() is in
drm_framebuffer. It's complicated by the state clear that occurs on
deadlock. ATM, there's no way to inject code in the deadlock path with
the helpers, so it's unfit for conversion.
Changes in v2:
- Relocate ret argument to the end of the list (Daniel)
- Incorporate Daniel's doc suggestions (Daniel)
Sean Paul [Thu, 29 Nov 2018 15:04:15 +0000 (10:04 -0500)]
drm: Move drm_mode_setcrtc() local re-init to failure path
Instead of always re-initializing the variables we need to clean up on
out, move the re-initialization into the branch that goes back to retry
label.
This is a lateral move right now, but will allow us to pull out the
modeset locking into common code. I kept this change separate to make
things easier to review.
Sean Paul [Thu, 29 Nov 2018 15:04:14 +0000 (10:04 -0500)]
drm: Clear state->acquire_ctx before leaving drm_atomic_helper_commit_duplicated_state()
drm_atomic_helper_commit_duplicated_state() sets state->acquire_ctx to
the context given in the argument and leaves it in state after it
quits. The lifetime of state and context are not guaranteed to be the
same, so we shouldn't leave that pointer hanging around. This patch
resets the context to NULL to avoid any oopses.
Noralf Trønnes [Wed, 28 Nov 2018 21:27:11 +0000 (22:27 +0100)]
drm/rcar-du: Use drm_fbdev_generic_setup()
The CMA helper is already using the drm_fb_helper_generic_probe part of
the generic fbdev emulation. This patch makes full use of the generic
fbdev emulation by using its drm_client callbacks. This means that
drm_mode_config_funcs->output_poll_changed and drm_driver->lastclose are
now handled by the emulation code. Additionally fbdev unregister happens
automatically on drm_dev_unregister().
The drm_fbdev_generic_setup() call is put after drm_dev_register() in the
driver. This is done to highlight the fact that fbdev emulation is an
internal client that makes use of the driver, it is not part of the
driver as such. If fbdev setup fails, an error is printed, but the driver
succeeds probing.
drm_fbdev_generic_setup() handles mode_config.num_connector being zero.
In that case it retries fbdev setup on the next .output_poll_changed.
Gerd Hoffmann [Wed, 28 Nov 2018 15:10:20 +0000 (16:10 +0100)]
drm/virtio: fence: pass plain pointer
Since commit "9fdd90c0f4 drm/virtio: add virtio_gpu_alloc_fence()"
fences are not allocated any more by virtio_gpu_fence_emit(). So there
is no need to pass down a reference to the fence pointer, a plain
pointer is enough now.
Dave Airlie [Thu, 29 Nov 2018 00:21:23 +0000 (10:21 +1000)]
Merge tag 'drm-misc-next-2018-11-28' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v4.21:
Core Changes:
- Merge drm_info.c into drm_debugfs.c
- Complete the fake drm_crtc_commit's hw_done/flip_done sooner.
- Remove deprecated drm_obj_ref/unref functions. All drivers use get/put now.
- Decrease stack use of drm_gem_prime_mmap.
- Improve documentation for dumb callbacks.
Driver Changes:
- Add edid support to virtio.
- Wait on implicit fence in meson and sun4i.
- Add support for BGRX8888 to sun4i.
- Preparation patches for sun4i driver to start supporting linear and tiled YUV formats.
- Add support for HDMI 1.4 4k modes to meson, and support for VIC alternate timings.
- Drop custom dumb_map in vkms.
- Small fixes and cleanups to v3d.
Eric Anholt [Mon, 26 Nov 2018 21:59:28 +0000 (13:59 -0800)]
drm/vkms: Drop custom vkms_dumb_map().
This is the same as the default drm_gem_dumb_map_offset()
implementation, except that this one missed the ban on userspace
mapping an imported dmabuf (which seems like intended common behavior
for drivers).
Neil Armstrong [Tue, 6 Nov 2018 10:54:35 +0000 (11:54 +0100)]
drm/meson: Add support for VIC alternate timings
This change is an attempt to handle the alternate clock for the CEA mode.
60Hz vs. 59.94Hz, 30Hz vs 29.97Hz or 24Hz vs 23.97Hz on the Amlogic Meson SoC
DRM Driver pixel clock generation.
The actual clock generation will be moved to the Common Clock framework once
all the video clock are handled by the Amlogic Meson SoC clock driver,
then these alternate timings will be handled in the same time in a cleaner
fashion.
Neil Armstrong [Tue, 6 Nov 2018 09:35:09 +0000 (10:35 +0100)]
drm/meson: Add HDMI 1.4 4k modes
Add the timings for the HDMI 1.4 4K modes support :
- 3840x2160@30
- 3840x2160@25
- 3840x2160@24
Since the 297000Hz pixel clock is already managed and the modes are
compatible with the HDMI 1.4 current HDMI PHY+Controller support, only
the missing timings values needs to be added.
Daniel Vetter [Tue, 27 Nov 2018 09:19:21 +0000 (10:19 +0100)]
drm: Improve dumb callback docs
Noticed while reviewing a patch from Eric. Also add a todo for the
dumb_map_offset callbacks (it should be simple to do, but piles of
work). Plus fix up vbox, because vbox.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Maxime Ripard <maxime.ripard@bootlin.com> Cc: Sean Paul <sean@poorly.run> Cc: David Airlie <airlied@linux.ie> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Nicholas Mc Guire <der.herr@hofr.at> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Fabio Rafael da Rosa <fdr@pid42.net> Reviewed-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20181127091921.8325-1-daniel.vetter@ffwll.ch
drm/sun4i: Make pitch even for GEM dumb alloc as per hardware constraint
Our hardware requires the pitch to be an even number when using YUV
formats with the frontend. Implement a driver-specific callback for GEM
dumb allocation that sets the pitch accordingly.
Since only the bpp is passed (and not the format), we cannot really
distinguish if this alignment is really required. Since it doesn't hurt
to align the pitch anyway, always do it.
drm/sun4i: frontend: Apply format sub-sampling to CH1 dimensions
The frontend comes with two "channels", that can be configured
independently. When used in YUV mode, the first channel (CH0) represents
the luminance component while the second channel (CH1) represents the
chrominance. In RGB mode, both have to be configured the same way.
Use variables (with the YUV terminology) for each channel's
dimensions, calculating the chroma dimensions from the luma dimensions
and the sub-sampling factors from the format description.
Since the configured size only has pixel precision, the fractional
fixed-point part of the source size is dropped for both components to
ensure that the scaling factors are accurate.
drm/sun4i: backend: Detail the YUV to RGB values coding explanation
The values in the BT601 YUV to RGB colorspace translation are not
simply coded as multiples, but rather as fixed-point signed fractional
values on a given number of bits. Add an explanation about that.
drm/sun4i: frontend: Add support for the BGRX8888 input format
This introduces support for the BGRX8888 input format for the frontend,
with its associated pixel sequence value definition. Other fields are
already configured correctly as they no longer depend on the format's
fourcc directly.
drm/sun4i: frontend: Determine input mode based on the number of planes
Use the number of planes associated with the DRM format to determine the
input mode configuration instead of the format iteself. This way, the
helper can be used for all packed formats without future changes.
drm/sun4i: frontend: Add proper definitions for format registers
This introduces proper definitions for the input and output format
configuration registers instead of a macro and raw values in the code,
with the intent to increase code readability and reduce indirections.
drm/sun4i: frontend: Add helpers for input data mode and pixel sequence
This introduces new helpers for retrieving the input data mode and pixel
sequence register field values based on the DRM format instead of
hardcoding these. This makes it easier to add support for more formats.
drm/sun4i: frontend: Move CSC bypass setup to format update routine
In order to support YUV to RGB conversion with the frontend (which is
generally used for connecting with the backend), the CSC block must not
be bypassed.
As a result, the bit to enable CSC bypass is moved from the runtime
resume routine to the format update routine, so that it can disabled
when introducing support for YUV formats later.
drm/sun4i: Rename sun4i_backend_layer_formats to sun4i_layer_formats
Since more formats can be supported by the frontend, rename the
variable listing the layer formats to avoid suggesting that the backend
itself supports all the listed formats.
drm/sun4i: backend: Avoid counting YUV planes that use the frontend
Our hardware has a limited number of YUV planes (usually 1) that can be
supported using the backend only. However, YUV planes can also be
supported by the frontend and must then not be counted when checking for
that limitation.
Only count the YUV plane when the frontend is not used.
drm/sun4i: backend: Use a specific function to check if a plane is supported
Before this patch, it is assumed that a plane is supported either
through the frontend or through the backend alone. However, the DRM
interface does not allow finely reporting our hardware capabilities
and there are cases where neither are support.
In particular, some plane formats are supported by the backend and not
the frontend, so they can only be supported without scaling.
drm/sun4i: backend: Refine the logic behind using the frontend
Checking that scaling is in use is not sufficient as a condition to
decide to use the frontend.
Since not all layer formats are supported by the frontend, we need to
check for that support first. Then, the frontend must only be enabled
if the backend doesn't support the format or that scaling is required.
drm/sun4i: frontend: Add a helper and a list for supported formats
In order to check whether the frontend supports a specific format, an
explicit list and a related helper are introduced.
Just like in the backend, the prototype of the helper is added to the
frontend header so that it can be used later on. The helper is also
exported because it will be used outside of the frontend module.
drm/sun4i: Add TODO comment about supporting scaling with the backend
The backend allows integer-only scaling but can handle alpha components,
unlike the frontend. It could be useful to add support for this
eventually, so add a short TODO comment describing the situation.
drm/sun4i: frontend: Replace ARGB with XRGB as supported format
The frontend documentation (for the A33) mentions that ARGB is supported
as output, but with the alpha component always set to 0xff. In practice,
this means that the alpha component cannot be preserved when going
through the frontend. Since the information is lost, ARGB is not
properly supported.
As a result, expose the matching format supported by the frontend (both
for input and output) as XRGB instead of ARGB.
Since ARGB was the selected format for connecting the frontend to the
backend, change it to XRGB to reflect this as well.
The A31 and A80 SoCs apparently have a bit to enable proper alpha,
but this is not supported at this point (see the comment already in the
code).
drm/sun4i: Cleanup video/YUV source before enabling a layer
This adds a dedicated function for cleaning the video and YUV source
channel layer enable bits. This function is called first on layer atomic
update to make sure that there are no leftover bits from previous
plane configuration that were not cleaned until now.
It fixes issues when alternating between video and YUV planes, where
both bits would be set eventually, leading to broken plane display.
Linus Torvalds [Sun, 25 Nov 2018 17:24:40 +0000 (09:24 -0800)]
Merge tag 'dma-mapping-4.20-3' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping fixes from Christoph Hellwig:
"Two dma-direct / swiotlb regressions fixes:
- zero is a valid physical address on some arm boards, we can't use
it as the error value
- don't try to cache flush the error return value (no matter what it
is)"
* tag 'dma-mapping-4.20-3' of git://git.infradead.org/users/hch/dma-mapping:
swiotlb: Skip cache maintenance on map error
dma-direct: Make DIRECT_MAPPING_ERROR viable for SWIOTLB
Linus Torvalds [Sun, 25 Nov 2018 17:19:58 +0000 (09:19 -0800)]
Merge tag 'nfs-for-4.20-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
- Fix a NFSv4 state manager deadlock when returning a delegation
- NFSv4.2 copy do not allocate memory under the lock
- flexfiles: Use the correct stateid for IO in the tightly coupled case
* tag 'nfs-for-4.20-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
flexfiles: use per-mirror specified stateid for IO
NFSv4.2 copy do not allocate memory under the lock
NFSv4: Fix a NFSv4 state manager deadlock
Linus Torvalds [Sun, 25 Nov 2018 02:44:01 +0000 (18:44 -0800)]
Merge tag 'xarray-4.20-rc4' of git://git.infradead.org/users/willy/linux-dax
Pull XArray updates from Matthew Wilcox:
"We found some bugs in the DAX conversion to XArray (and one bug which
predated the XArray conversion). There were a couple of bugs in some
of the higher-level functions, which aren't actually being called in
today's kernel, but surfaced as a result of converting existing radix
tree & IDR users over to the XArray.
Some of the other changes to how the higher-level APIs work were also
motivated by converting various users; again, they're not in use in
today's kernel, so changing them has a low probability of introducing
a bug.
Dan can still trigger a bug in the DAX code with hot-offline/online,
and we're working on tracking that down"
* tag 'xarray-4.20-rc4' of git://git.infradead.org/users/willy/linux-dax:
XArray tests: Add missing locking
dax: Avoid losing wakeup in dax_lock_mapping_entry
dax: Fix huge page faults
dax: Fix dax_unlock_mapping_entry for PMD pages
dax: Reinstate RCU protection of inode
dax: Make sure the unlocking entry isn't locked
dax: Remove optimisation from dax_lock_mapping_entry
XArray tests: Correct some 64-bit assumptions
XArray: Correct xa_store_range
XArray: Fix Documentation
XArray: Handle NULL pointers differently for allocation
XArray: Unify xa_store and __xa_store
XArray: Add xa_store_bh() and xa_store_irq()
XArray: Turn xa_erase into an exported function
XArray: Unify xa_cmpxchg and __xa_cmpxchg
XArray: Regularise xa_reserve
nilfs2: Use xa_erase_irq
XArray: Export __xa_foo to non-GPL modules
XArray: Fix xa_for_each with a single element at 0
Linus Torvalds [Sat, 24 Nov 2018 20:58:47 +0000 (12:58 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID fixes from Jiri Kosina:
- revert of the high-resolution scrolling feature, as it breaks certain
hardware due to incompatibilities between Logitech and Microsoft
worlds. Peter Hutterer is working on a fixed implementation. Until
that is finished, revert by Benjamin Tissoires.
- revert of incorrect strncpy->strlcpy conversion in uhid, from David
Herrmann
- fix for buggy sendfile() implementation on uhid device node, from
Eric Biggers
- a few assorted device-ID specific quirks
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
Revert "Input: Add the `REL_WHEEL_HI_RES` event code"
Revert "HID: input: Create a utility class for counting scroll events"
Revert "HID: logitech: Add function to enable HID++ 1.0 "scrolling acceleration""
Revert "HID: logitech: Enable high-resolution scrolling on Logitech mice"
Revert "HID: logitech: Use LDJ_DEVICE macro for existing Logitech mice"
Revert "HID: logitech: fix a used uninitialized GCC warning"
Revert "HID: input: simplify/fix high-res scroll event handling"
HID: Add quirk for Primax PIXART OEM mice
HID: i2c-hid: Disable runtime PM for LG touchscreen
HID: multitouch: Add pointstick support for Cirque Touchpad
HID: steam: remove input device when a hid client is running.
Revert "HID: uhid: use strlcpy() instead of strncpy()"
HID: uhid: forbid UHID_CREATE under KERNEL_DS or elevated privileges
HID: input: Ignore battery reported by Symbol DS4308
HID: Add quirk for Microsoft PIXART OEM mouse
projects / mirror_ubuntu-kernels.git / log