The Olimex Olinuxino board has a user led connected to SSP1_DETECT.
But since this pin is listed in mmc0_pins_fixup, it is already claimed
by MMC driver and this results in this error during boot:
[ 1.390000] imx23-pinctrl 80018000.pinctrl: pin SSP1_DETECT already
requested by 80010000.spi; cannot claim for leds
[ 1.400000] imx23-pinctrl 80018000.pinctrl: pin-65 (leds) status -22
[ 1.410000] imx23-pinctrl 80018000.pinctrl: could not request pin 65
(SSP1_DETECT) from group led_gpio2_1.0 on device 80018000.pinctrl
[ 1.420000] leds-gpio leds: Error applying setting, reverse things back
[ 1.430000] leds-gpio: probe of leds failed with error -22
This fix it, introduce mmc0_sck_cfg and switch the Olinuxino board to it.
Signed-off-by: Michael Heimpold <mhei@heimpold.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Marco Felsch [Thu, 27 Feb 2020 11:06:05 +0000 (12:06 +0100)]
ARM: dts: imx6: phycore-som: add da9062 gpio support
The pmic is a mfd device and supports gpios. Those gpios are not routed
to the SoM baseboard pin header but they are connected to the i.MX6. We
need the GPIO's to configure the pmic to select between the
suspend/resume arm and soc voltages
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Marco Felsch [Thu, 27 Feb 2020 11:06:04 +0000 (12:06 +0100)]
ARM: dts: imx6: phycore-som: explicit disable pmic watchdog during suspend
By default the phycore-som has support for two watchdog devices: 1st the
internal imx6 watchdog and 2nd the DA9062 PMIC watchdog. According [1]
the PMIC watchdog is used as boot watchdog. It is common to use this
watchdog during "system up" time too. Furthermore the PMIC watchdog can
be used to address ERR007117 since the phycore-som can be equipped with
NAND or eMMC storage.
The PMIC watchdog can be enabled/disabled by the PMIC itself if the PMIC
enters POWERDOWN mode or by the host. The PMIC powerdown mode can't be
used due to the PCB design. So the watchdog is still enabled during a
suspend which causes a system reset. We need to tell the driver to
disable the watchdog during a system suspend and to reenable it upon a
resume to fix this.
André Draszik [Tue, 25 Feb 2020 16:11:57 +0000 (16:11 +0000)]
ARM: dts: imx7s: add snvs clock to pwrkey
On i.MX7, the SNVS requires a clock. This is similar to the clock
bound to the SNVS RTC node, but if the SNVS RTC driver isn't enabled,
then SNVS doesn't work, and as such the pwrkey driver doesn't
work (i.e. hangs the kernel, as the clock isn't enabled).
Also see commit ec2a844ef7c1
("ARM: dts: imx7s: add snvs rtc clock")
for a similar fix.
Signed-off-by: André Draszik <git@andred.net> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Anson Huang [Mon, 17 Feb 2020 11:13:35 +0000 (19:13 +0800)]
ARM: dts: imx6sx: Improve UART pins macro defines
Add DCE/DTE to UART pins macro defines to distinguish the
DCE and DTE functions, keep old defines at the end of file
for some time to make it backward compatible.
Peng Fan [Thu, 13 Feb 2020 03:17:58 +0000 (11:17 +0800)]
ARM: dts: imx: use generic name bus
Per devicetree specification, generic names
are recommended to be used, such as bus.
i.MX AIPS is a AHB - IP bridge bus, so
we could use bus as node name.
Script:
sed -i "s/\<aips@/bus@/" arch/arm/boot/dts/imx*.dtsi
sed -i "s/\<aips@/bus@/" arch/arm/boot/dts/vf*.dtsi
sed -i "s/\<aips-bus@/bus@/" arch/arm/boot/dts/imx*.dtsi
sed -i "s/\<aips-bus@/bus@/" arch/arm/boot/dts/vf*.dtsi
Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stefan Agner [Wed, 29 Jan 2020 21:53:36 +0000 (22:53 +0100)]
ARM: dts: imx7-colibri: add gpio-line-names
Add Colibri SODIMM numbers as GPIO line names on module level. The GPIO
lines with a name are all available on the SODIMM edge connector of the
Colibri iMX7 module and therefore a customer might use it as a GPIO. The
Toradex Evaluation Board has the SODIMM numbers printed on the silk-
screen. This allows a customer to quickly control a GPIO on a pin-header
by using the name printed next to it.
Putting the GPIO line name on module level makes sure that a customer
gets a reasonable default. If more meaningful names are available on a
custom carrier board, the user can overwrite the line names in a carrier
board level device tree.
The eMMC based modules share all GPIO names except two GPIOs on bank 6
which are not available on the raw NAND devices. Hence overwrite GPIO
line names of bank 6 in the eMMC specific device tree file.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Peter Chen [Thu, 23 Jan 2020 02:51:44 +0000 (10:51 +0800)]
ARM: dts: imx7ulp-evk: disable usbotg1 overcurrent function
At imx7ulp evk, all USBOTG1 OC (Over Current) function pins are
used by others, and the USB driver doesn't support OC function
through the GPIO, so we disable the OC function for this board
as well as delete the pinctrl for it.
Reviewed-by: Jun Li <jun.li@nxp.com> Acked-by: Leonard Crestez <leonard.crestez@nxp.com> Signed-off-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Linus Torvalds [Mon, 10 Feb 2020 00:05:50 +0000 (16:05 -0800)]
Merge tag 'kbuild-v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- fix randconfig to generate a sane .config
- rename hostprogs-y / always to hostprogs / always-y, which are more
natual syntax.
- optimize scripts/kallsyms
- fix yes2modconfig and mod2yesconfig
- make multiple directory targets ('make foo/ bar/') work
* tag 'kbuild-v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: make multiple directory targets work
kconfig: Invalidate all symbols after changing to y or m.
kallsyms: fix type of kallsyms_token_table[]
scripts/kallsyms: change table to store (strcut sym_entry *)
scripts/kallsyms: rename local variables in read_symbol()
kbuild: rename hostprogs-y/always to hostprogs/always-y
kbuild: fix the document to use extra-y for vmlinux.lds
kconfig: fix broken dependency in randconfig-generated .config
Linus Torvalds [Sun, 9 Feb 2020 23:51:46 +0000 (15:51 -0800)]
Merge tag 'zonefs-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs
Pull new zonefs file system from Damien Le Moal:
"Zonefs is a very simple file system exposing each zone of a zoned
block device as a file.
Unlike a regular file system with native zoned block device support
(e.g. f2fs or the on-going btrfs effort), zonefs does not hide the
sequential write constraint of zoned block devices to the user. As a
result, zonefs is not a POSIX compliant file system. Its goal is to
simplify the implementation of zoned block devices support in
applications by replacing raw block device file accesses with a richer
file based API, avoiding relying on direct block device file ioctls
which may be more obscure to developers.
One example of this approach is the implementation of LSM
(log-structured merge) tree structures (such as used in RocksDB and
LevelDB) on zoned block devices by allowing SSTables to be stored in a
zone file similarly to a regular file system rather than as a range of
sectors of a zoned device. The introduction of the higher level
construct "one file is one zone" can help reducing the amount of
changes needed in the application while at the same time allowing the
use of zoned block devices with various programming languages other
than C.
Zonefs IO management implementation uses the new iomap generic code.
Zonefs has been successfully tested using a functional test suite
(available with zonefs userland format tool on github) and a prototype
implementation of LevelDB on top of zonefs"
* tag 'zonefs-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs:
zonefs: Add documentation
fs: New zonefs file system
Linus Torvalds [Sun, 9 Feb 2020 21:27:17 +0000 (13:27 -0800)]
Merge tag '5.6-rc-smb3-plugfest-patches' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"13 cifs/smb3 patches, most from testing at the SMB3 plugfest this week:
- Important fix for multichannel and for modefromsid mounts.
- Two reconnect fixes
- Addition of SMB3 change notify support
- Backup tools fix
- A few additional minor debug improvements (tracepoints and
additional logging found useful during testing this week)"
* tag '5.6-rc-smb3-plugfest-patches' of git://git.samba.org/sfrench/cifs-2.6:
smb3: Add defines for new information level, FileIdInformation
smb3: print warning once if posix context returned on open
smb3: add one more dynamic tracepoint missing from strict fsync path
cifs: fix mode bits from dir listing when mounted with modefromsid
cifs: fix channel signing
cifs: add SMB3 change notification support
cifs: make multichannel warning more visible
cifs: fix soft mounts hanging in the reconnect code
cifs: Add tracepoints for errors on flush or fsync
cifs: log warning message (once) if out of disk space
cifs: fail i/o on soft mounts if sessionsetup errors out
smb3: fix problem with null cifs super block with previous patch
SMB3: Backup intent flag missing from some more ops
Linus Torvalds [Sun, 9 Feb 2020 20:41:00 +0000 (12:41 -0800)]
Merge branch 'work.vboxsf' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vboxfs from Al Viro:
"This is the VirtualBox guest shared folder support by Hans de Goede,
with fixups for fs_parse folded in to avoid bisection hazards from
those API changes..."
* 'work.vboxsf' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: Add VirtualBox guest shared folder (vboxsf) support
Linus Torvalds [Sun, 9 Feb 2020 20:11:12 +0000 (12:11 -0800)]
Merge tag 'x86-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A set of fixes for X86:
- Ensure that the PIT is set up when the local APIC is disable or
configured in legacy mode. This is caused by an ordering issue
introduced in the recent changes which skip PIT initialization when
the TSC and APIC frequencies are already known.
- Handle malformed SRAT tables during early ACPI parsing which caused
an infinite loop anda boot hang.
- Fix a long standing race in the affinity setting code which affects
PCI devices with non-maskable MSI interrupts. The problem is caused
by the non-atomic writes of the MSI address (destination APIC id)
and data (vector) fields which the device uses to construct the MSI
message. The non-atomic writes are mandated by PCI.
If both fields change and the device raises an interrupt after
writing address and before writing data, then the MSI block
constructs a inconsistent message which causes interrupts to be
lost and subsequent malfunction of the device.
The fix is to redirect the interrupt to the new vector on the
current CPU first and then switch it over to the new target CPU.
This allows to observe an eventually raised interrupt in the
transitional stage (old CPU, new vector) to be observed in the APIC
IRR and retriggered on the new target CPU and the new vector.
The potential spurious interrupts caused by this are harmless and
can in the worst case expose a buggy driver (all handlers have to
be able to deal with spurious interrupts as they can and do happen
for various reasons).
- Add the missing suspend/resume mechanism for the HYPERV hypercall
page which prevents resume hibernation on HYPERV guests. This
change got lost before the merge window.
- Mask the IOAPIC before disabling the local APIC to prevent
potentially stale IOAPIC remote IRR bits which cause stale
interrupt lines after resume"
* tag 'x86-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic: Mask IOAPIC entries when disabling the local APIC
x86/hyperv: Suspend/resume the hypercall page for hibernation
x86/apic/msi: Plug non-maskable MSI affinity race
x86/boot: Handle malformed SRAT tables during early ACPI parsing
x86/timer: Don't skip PIT setup when APIC is disabled or in legacy mode
Linus Torvalds [Sun, 9 Feb 2020 20:09:43 +0000 (12:09 -0800)]
Merge tag 'smp-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull SMP fixes from Thomas Gleixner:
"Two fixes for the SMP related functionality:
- Make the UP version of smp_call_function_single() match SMP
semantics when called for a not available CPU. Instead of emitting
a warning and assuming that the function call target is CPU0,
return a proper error code like the SMP version does.
- Remove a superfluous check in smp_call_function_many_cond()"
* tag 'smp-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
smp/up: Make smp_call_function_single() match SMP semantics
smp: Remove superfluous cond_func check in smp_call_function_many_cond()
Linus Torvalds [Sun, 9 Feb 2020 20:04:09 +0000 (12:04 -0800)]
Merge tag 'perf-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Thomas Gleixner:
"A set of fixes and improvements for the perf subsystem:
Kernel fixes:
- Install cgroup events to the correct CPU context to prevent a
potential list double add
- Prevent an integer underflow in the perf mlock accounting
- Add a missing prototype for arch_perf_update_userpage()
Tooling:
- Add a missing unlock in the error path of maps__insert() in perf
maps.
- Fix the build with the latest libbfd
- Fix the perf parser so it does not delete parse event terms, which
caused a regression for using perf with the ARM CoreSight as the
sink configuration was missing due to the deletion.
- Fix the double free in the perf CPU map merging test case
- Add the missing ustring support for the perf probe command"
* tag 'perf-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf maps: Add missing unlock to maps__insert() error case
perf probe: Add ustring support for perf probe command
perf: Make perf able to build with latest libbfd
perf test: Fix test case Merge cpu map
perf parse: Copy string to perf_evsel_config_term
perf parse: Refactor 'struct perf_evsel_config_term'
kernel/events: Add a missing prototype for arch_perf_update_userpage()
perf/cgroups: Install cgroup events to correct cpuctx
perf/core: Fix mlock accounting in perf_mmap()
Linus Torvalds [Sun, 9 Feb 2020 20:00:12 +0000 (12:00 -0800)]
Merge tag 'timers-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"Two small fixes for the time(r) subsystem:
- Handle a subtle race between the clocksource watchdog and a
concurrent clocksource watchdog stop/start sequence correctly to
prevent a timer double add bug.
- Fix the file path for the core time namespace file"
* tag 'timers-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: Prevent double add_timer_on() for watchdog_timer
MAINTAINERS: Correct path to time namespace source file
Linus Torvalds [Sun, 9 Feb 2020 19:56:41 +0000 (11:56 -0800)]
Merge tag 'irq-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull interrupt fixes from Thomas Gleixner:
"A set of fixes for the interrupt subsystem:
- Provision only ACPI enabled redistributors on GICv3
- Use the proper command colums when building the INVALL command for
the GICv3-ITS
- Ensure the allocation of the L2 vPE table for GICv4.1
- Correct the GICv4.1 VPROBASER programming so it uses the proper
size
- A set of small GICv4.1 tidy up patches
- Configuration cleanup for C-SKY interrupt chip
- Clarify the function documentation for irq_set_wake() to document
that the wakeup functionality is orthogonal to the irq
disable/enable mechanism"
* tag 'irq-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3-its: Rename VPENDBASER/VPROPBASER accessors
irqchip/gic-v3-its: Remove superfluous WARN_ON
irqchip/gic-v4.1: Drop 'tmp' in inherit_vpe_l1_table_from_rd()
irqchip/gic-v4.1: Ensure L2 vPE table is allocated at RD level
irqchip/gic-v4.1: Set vpe_l1_base for all redistributors
irqchip/gic-v4.1: Fix programming of GICR_VPROPBASER_4_1_SIZE
genirq: Clarify that irq wake state is orthogonal to enable/disable
irqchip/gic-v3-its: Reference to its_invall_cmd descriptor when building INVALL
irqchip: Some Kconfig cleanup for C-SKY
irqchip/gic-v3: Only provision redistributors that are enabled in ACPI
Linus Torvalds [Sun, 9 Feb 2020 19:54:50 +0000 (11:54 -0800)]
Merge tag 'efi-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fix from Thomas Gleixner:
"A single fix for a EFI boot regression on X86 which was caused by the
recent rework of the EFI memory map parsing. On systems with invalid
memmap entries the cleanup function uses an value which cannot be
relied on in this stage. Use the actual EFI memmap entry instead"
* tag 'efi-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/x86: Fix boot regression on systems with invalid memmap entries
1) Unbalanced locking in mwifiex_process_country_ie, from Brian Norris.
2) Fix thermal zone registration in iwlwifi, from Andrei
Otcheretianski.
3) Fix double free_irq in sgi ioc3 eth, from Thomas Bogendoerfer.
4) Use after free in mptcp, from Florian Westphal.
5) Use after free in wireguard's root_remove_peer_lists, from Eric
Dumazet.
6) Properly access packets heads in bonding alb code, from Eric
Dumazet.
7) Fix data race in skb_queue_len(), from Qian Cai.
8) Fix regression in r8169 on some chips, from Heiner Kallweit.
9) Fix XDP program ref counting in hv_netvsc, from Haiyang Zhang.
10) Certain kinds of set link netlink operations can cause a NULL deref
in the ipv6 addrconf code. Fix from Eric Dumazet.
11) Don't cancel uninitialized work queue in drop monitor, from Ido
Schimmel.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (84 commits)
net: thunderx: use proper interface type for RGMII
mt76: mt7615: fix max_nss in mt7615_eeprom_parse_hw_cap
bpf: Improve bucket_log calculation logic
selftests/bpf: Test freeing sockmap/sockhash with a socket in it
bpf, sockhash: Synchronize_rcu before free'ing map
bpf, sockmap: Don't sleep while holding RCU lock on tear-down
bpftool: Don't crash on missing xlated program instructions
bpf, sockmap: Check update requirements after locking
drop_monitor: Do not cancel uninitialized work item
mlxsw: spectrum_dpipe: Add missing error path
mlxsw: core: Add validation of hardware device types for MGPIR register
mlxsw: spectrum_router: Clear offload indication from IPv6 nexthops on abort
selftests: mlxsw: Add test cases for local table route replacement
mlxsw: spectrum_router: Prevent incorrect replacement of local table routes
net: dsa: microchip: enable module autoprobe
ipv6/addrconf: fix potential NULL deref in inet6_set_link_af()
dpaa_eth: support all modes with rate adapting PHYs
net: stmmac: update pci platform data to use phy_interface
net: stmmac: xgmac: fix missing IFF_MULTICAST checki in dwxgmac2_set_filter
net: stmmac: fix missing IFF_MULTICAST check in dwmac4_set_filter
...
Hans de Goede [Thu, 12 Dec 2019 14:09:14 +0000 (15:09 +0100)]
fs: Add VirtualBox guest shared folder (vboxsf) support
VirtualBox hosts can share folders with guests, this commit adds a
VFS driver implementing the Linux-guest side of this, allowing folders
exported by the host to be mounted under Linux.
This driver depends on the guest <-> host IPC functions exported by
the vboxguest driver.
Acked-by: Christoph Hellwig <hch@infradead.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Linus Torvalds [Sat, 8 Feb 2020 22:28:26 +0000 (14:28 -0800)]
Merge tag 'powerpc-5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix an existing bug in our user access handling, exposed by one of
the bug fixes we merged this cycle.
- A fix for a boot hang on 32-bit with CONFIG_TRACE_IRQFLAGS and the
recently added CONFIG_VMAP_STACK.
Thanks to: Christophe Leroy, Guenter Roeck.
* tag 'powerpc-5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc: Fix CONFIG_TRACE_IRQFLAGS with CONFIG_VMAP_STACK
powerpc/futex: Fix incorrect user access blocking
Linus Torvalds [Sat, 8 Feb 2020 22:19:39 +0000 (14:19 -0800)]
Fix up remaining devm_ioremap_nocache() in SGI IOC3 8250 UART driver
This is a merge error on my part - the driver was merged into mainline
by commit c5951e7c8ee5 ("Merge tag 'mips_5.6' of git://../mips/linux")
over a week ago, but nobody apparently noticed that it didn't actually
build due to still having a reference to the devm_ioremap_nocache()
function, removed a few days earlier through commit 6a1000bd2703 ("Merge
tag 'ioremap-5.6' of git://../ioremap").
Apparently this didn't get any build testing anywhere. Not perhaps all
that surprising: it's restricted to 64-bit MIPS only, and only with the
new SGI_MFD_IOC3 support enabled.
I only noticed because the ioremap conflicts in the ARM SoC driver
update made me check there weren't any others hiding, and I found this
one.
Linus Torvalds [Sat, 8 Feb 2020 22:17:27 +0000 (14:17 -0800)]
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC late updates from Olof Johansson:
"This is some material that we picked up into our tree late, or that
had more complex dependencies on more than one topic branch that makes
sense to keep separately.
- TI support for secure accelerators and hwrng on OMAP4/5
- TI camera changes for dra7 and am437x and SGX improvement due to
better reset control support on am335x, am437x and dra7
- Davinci moves to proper clocksource on DM365, and regulator/audio
improvements for DM365 and DM644x eval boards"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (32 commits)
ARM: dts: omap4-droid4: Enable hdq for droid4 ds250x 1-wire battery nvmem
ARM: dts: motorola-cpcap-mapphone: Configure calibration interrupt
ARM: dts: Configure interconnect target module for am437x sgx
ARM: dts: Configure sgx for dra7
ARM: dts: Configure rstctrl reset for am335x SGX
ARM: dts: dra7: Add ti-sysc node for VPE
ARM: dts: dra7: add vpe clkctrl node
ARM: dts: am43x-epos-evm: Add VPFE and OV2659 entries
ARM: dts: am437x-sk-evm: Add VPFE and OV2659 entries
ARM: dts: am43xx: add support for clkout1 clock
arm: dts: dra76-evm: Add CAL and OV5640 nodes
arm: dtsi: dra76x: Add CAL dtsi node
arm: dts: dra72-evm-common: Add entries for the CSI2 cameras
ARM: dts: DRA72: Add CAL dtsi node
ARM: dts: dra7-l4: Add ti-sysc node for CAM
ARM: OMAP: DRA7xx: Make CAM clock domain SWSUP only
ARM: dts: dra7: add cam clkctrl node
ARM: OMAP2+: Drop legacy platform data for omap4 des
ARM: OMAP2+: Drop legacy platform data for omap4 sham
ARM: OMAP2+: Drop legacy platform data for omap4 aes
...
Linus Torvalds [Sat, 8 Feb 2020 22:15:41 +0000 (14:15 -0800)]
Merge tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC defconfig updates from Olof Johansson:
"We keep this in a separate branch to avoid cross-branch conflicts, but
most of the material here is fairly boring -- some new drivers turned
on for hardware since they were merged, and some refreshed files due
to time having moved a lot of entries around"
* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (38 commits)
ARM: configs: at91: enable MMC_SDHCI_OF_AT91 and MICROCHIP_PIT64B
arm64: defconfig: Enable Broadcom's GENET Ethernet controller
ARM: multi_v7_defconfig: Enable devfreq thermal integration
ARM: exynos_defconfig: Enable devfreq thermal integration
ARM: multi_v7_defconfig: Enable NFS v4.1 and v4.2
ARM: exynos_defconfig: Enable NFS v4.1 and v4.2
arm64: defconfig: Enable Actions Semi specific drivers
arm64: defconfig: Enable Broadcom's STB PCIe controller
arm64: defconfig: Enable CONFIG_CLK_IMX8MP by default
ARM: configs: at91: enable config flags for sam9x60 SoC
ARM: configs: at91: use savedefconfig
arm64: defconfig: Enable tegra XUDC support
ARM: defconfig: gemini: Update defconfig
arm64: defconfig: enable CONFIG_ARM_QCOM_CPUFREQ_NVMEM
arm64: defconfig: enable CONFIG_QCOM_CPR
arm64: defconfig: Enable HFPLL
arm64: defconfig: Enable CRYPTO_DEV_FSL_CAAM
ARM: imx_v6_v7_defconfig: Select the TFP410 driver
ARM: imx_v6_v7_defconfig: Enable NFS_V4_1 and NFS_V4_2 support
arm64: defconfig: Enable ATH10K_SNOC
...
Linus Torvalds [Sat, 8 Feb 2020 22:04:19 +0000 (14:04 -0800)]
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller
pieces for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support
ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
and misc cleanups, refactorings of Marvell, TI, other platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (166 commits)
drivers: soc: xilinx: Use mailbox IPI callback
dt-bindings: power: reset: xilinx: Add bindings for ipi mailbox
drivers: soc: ti: knav_qmss_queue: Pass lockdep expression to RCU lists
MAINTAINERS: Add brcmstb PCIe controller entry
soc/tegra: fuse: Unmap registers once they are not needed anymore
soc/tegra: fuse: Correct straps' address for older Tegra124 device trees
soc/tegra: fuse: Warn if straps are not ready
soc/tegra: fuse: Cache values of straps and Chip ID registers
memory: tegra30-emc: Correct error message for timed out auto calibration
memory: tegra30-emc: Firm up hardware programming sequence
memory: tegra30-emc: Firm up suspend/resume sequence
soc/tegra: regulators: Do nothing if voltage is unchanged
memory: tegra: Correct reset value of xusb_hostr
soc/tegra: fuse: Add APB DMA dependency for Tegra20
bus: tegra-aconnect: Remove PM_CLK dependency
dt-bindings: mediatek: add MT6765 power dt-bindings
soc: mediatek: cmdq: delete not used define
memory: tegra: Add support for the Tegra194 memory controller
memory: tegra: Only include support for enabled SoCs
memory: tegra: Support DVFS on Tegra186 and later
...
Linus Torvalds [Sat, 8 Feb 2020 21:55:25 +0000 (13:55 -0800)]
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"Most of these are smaller fixes that have accrued, and some continued
cleanup of OMAP platforms towards shared frameworks.
One new SoC from Atmel/Microchip: sam9x60"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (35 commits)
ARM: OMAP2+: Fix undefined reference to omap_secure_init
ARM: s3c64xx: Drop unneeded select of TIMER_OF
ARM: exynos: Drop unneeded select of MIGHT_HAVE_CACHE_L2X0
ARM: s3c24xx: Switch to atomic pwm API in rx1950
ARM: OMAP2+: sleep43xx: Call secure suspend/resume handlers
ARM: OMAP2+: Use ARM SMC Calling Convention when OP-TEE is available
ARM: OMAP2+: Introduce check for OP-TEE in omap_secure_init()
ARM: OMAP2+: Add omap_secure_init callback hook for secure initialization
ARM: at91: Documentation: add sam9x60 product and datasheet
ARM: at91: pm: use of_device_id array to find the proper shdwc node
ARM: at91: pm: use SAM9X60 PMC's compatible
ARM: imx: only select ARM_ERRATA_814220 for ARMv7-A
ARM: zynq: use physical cpuid in zynq_slcr_cpu_stop/start
ARM: tegra: Use clk_m CPU on Tegra124 LP1 resume
ARM: tegra: Modify reshift divider during LP1
ARM: tegra: Enable PLLP bypass during Tegra124 LP1
ARM: samsung: Rename Samsung and Exynos to lowercase
ARM: exynos: Correct the help text for platform Kconfig option
ARM: bcm: Select ARM_AMBA for ARCH_BRCMSTB
ARM: brcmstb: Add debug UART entry for 7216
...
Linus Torvalds [Sat, 8 Feb 2020 21:44:41 +0000 (13:44 -0800)]
Merge tag 'compat-ioctl-fix' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground
Pull compat-ioctl fix from Arnd Bergmann:
"One patch in the compat-ioctl series broke 32-bit rootfs for multiple
people testing on 64-bit kernels. Let's fix it in -rc1 before others
run into the same issue"
* tag 'compat-ioctl-fix' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground:
compat_ioctl: fix FIONREAD on devices
Linus Torvalds [Sat, 8 Feb 2020 21:26:41 +0000 (13:26 -0800)]
Merge branch 'merge.nfs-fs_parse.1' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs file system parameter updates from Al Viro:
"Saner fs_parser.c guts and data structures. The system-wide registry
of syntax types (string/enum/int32/oct32/.../etc.) is gone and so is
the horror switch() in fs_parse() that would have to grow another case
every time something got added to that system-wide registry.
New syntax types can be added by filesystems easily now, and their
namespace is that of functions - not of system-wide enum members. IOW,
they can be shared or kept private and if some turn out to be widely
useful, we can make them common library helpers, etc., without having
to do anything whatsoever to fs_parse() itself.
And we already get that kind of requests - the thing that finally
pushed me into doing that was "oh, and let's add one for timeouts -
things like 15s or 2h". If some filesystem really wants that, let them
do it. Without somebody having to play gatekeeper for the variants
blessed by direct support in fs_parse(), TYVM.
Quite a bit of boilerplate is gone. And IMO the data structures make a
lot more sense now. -200LoC, while we are at it"
* 'merge.nfs-fs_parse.1' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (25 commits)
tmpfs: switch to use of invalfc()
cgroup1: switch to use of errorfc() et.al.
procfs: switch to use of invalfc()
hugetlbfs: switch to use of invalfc()
cramfs: switch to use of errofc() et.al.
gfs2: switch to use of errorfc() et.al.
fuse: switch to use errorfc() et.al.
ceph: use errorfc() and friends instead of spelling the prefix out
prefix-handling analogues of errorf() and friends
turn fs_param_is_... into functions
fs_parse: handle optional arguments sanely
fs_parse: fold fs_parameter_desc/fs_parameter_spec
fs_parser: remove fs_parameter_description name field
add prefix to fs_context->log
ceph_parse_param(), ceph_parse_mon_ips(): switch to passing fc_log
new primitive: __fs_parse()
switch rbd and libceph to p_log-based primitives
struct p_log, variants of warnf() et.al. taking that one instead
teach logfc() to handle prefices, give it saner calling conventions
get rid of cg_invalf()
...
Linus Torvalds [Sat, 8 Feb 2020 21:04:49 +0000 (13:04 -0800)]
Merge branch 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull misc vfs updates from Al Viro:
- bmap series from cmaiolino
- getting rid of convolutions in copy_mount_options() (use a couple of
copy_from_user() instead of the __get_user() crap)
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
saner copy_mount_options()
fibmap: Reject negative block numbers
fibmap: Use bmap instead of ->bmap method in ioctl_fibmap
ecryptfs: drop direct calls to ->bmap
cachefiles: drop direct usage of ->bmap method.
fs: Enable bmap() function to properly return errors
Linus Torvalds [Sat, 8 Feb 2020 19:44:02 +0000 (11:44 -0800)]
Merge branch 'pipe-exclusive-wakeup'
Merge thundering herd avoidance on pipe IO.
This would have been applied for 5.5 already, but got delayed because of
a user-space race condition in the GNU make jobserver code. Now that
there's a new GNU make 4.3 release, and most distributions seem to have
at least applied the (almost three year old) fix for the problem, let's
see if people notice.
And it might have been just bad random timing luck on my machine.
If you do hit the race condition, things will still work, but the
symptom is that you don't get nearly the expected parallelism when using
"make -j<N>".
The jobserver bug can definitely happen without this patch too, but
seems to be easier to trigger when we no longer wake up pipe waiters
unnecessarily.
* pipe-exclusive-wakeup:
pipe: use exclusive waits when reading or writing
Linus Torvalds [Mon, 9 Dec 2019 17:48:27 +0000 (09:48 -0800)]
pipe: use exclusive waits when reading or writing
This makes the pipe code use separate wait-queues and exclusive waiting
for readers and writers, avoiding a nasty thundering herd problem when
there are lots of readers waiting for data on a pipe (or, less commonly,
lots of writers waiting for a pipe to have space).
While this isn't a common occurrence in the traditional "use a pipe as a
data transport" case, where you typically only have a single reader and
a single writer process, there is one common special case: using a pipe
as a source of "locking tokens" rather than for data communication.
In particular, the GNU make jobserver code ends up using a pipe as a way
to limit parallelism, where each job consumes a token by reading a byte
from the jobserver pipe, and releases the token by writing a byte back
to the pipe.
This pattern is fairly traditional on Unix, and works very well, but
will waste a lot of time waking up a lot of processes when only a single
reader needs to be woken up when a writer releases a new token.
A simplified test-case of just this pipe interaction is to create 64
processes, and then pass a single token around between them (this
test-case also intentionally passes another token that gets ignored to
test the "wake up next" logic too, in case anybody wonders about it):
#include <unistd.h>
int main(int argc, char **argv)
{
int fd[2], counters[2];
do {
int i;
read(fd[0], &i, sizeof(i));
if (i < 0)
continue;
counters[0] = i+1;
write(fd[1], counters, (1+(i & 1)) *sizeof(int));
} while (counters[0] < 1000000);
return 0;
}
and in a perfect world, passing that token around should only cause one
context switch per transfer, when the writer of a token causes a
directed wakeup of just a single reader.
But with the "writer wakes all readers" model we traditionally had, on
my test box the above case causes more than an order of magnitude more
scheduling: instead of the expected ~1M context switches, "perf stat"
shows
[ Note! This kernel improvement seems to be very good at triggering a
race condition in the make jobserver (in GNU make 4.2.1) for me. It's
a long known bug that was fixed back in June 2017 by GNU make commit b552b0525198 ("[SV 51159] Use a non-blocking read with pselect to
avoid hangs.").
But there wasn't a new release of GNU make until 4.3 on Jan 19 2020,
so a number of distributions may still have the buggy version. Some
have backported the fix to their 4.2.1 release, though, and even
without the fix it's quite timing-dependent whether the bug actually
is hit. ]
Josh Triplett says:
"I've been hammering on your pipe fix patch (switching to exclusive
wait queues) for a month or so, on several different systems, and I've
run into no issues with it. The patch *substantially* improves
parallel build times on large (~100 CPU) systems, both with parallel
make and with other things that use make's pipe-based jobserver.
All current distributions (including stable and long-term stable
distributions) have versions of GNU make that no longer have the
jobserver bug"
Arnd Bergmann [Fri, 7 Feb 2020 16:55:48 +0000 (17:55 +0100)]
compat_ioctl: fix FIONREAD on devices
My final cleanup patch for sys_compat_ioctl() introduced a regression on
the FIONREAD ioctl command, which is used for both regular and special
files, but only works on regular files after my patch, as I had missed
the warning that Al Viro put into a comment right above it.
Change it back so it can work on any file again by moving the implementation
to do_vfs_ioctl() instead.
Fixes: 77b9040195de ("compat_ioctl: simplify the implementation") Reported-and-tested-by: Christian Zigotzky <chzigotzky@xenosoft.de> Reported-and-tested-by: youling257 <youling257@gmail.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tim Harvey [Fri, 7 Feb 2020 20:40:26 +0000 (12:40 -0800)]
net: thunderx: use proper interface type for RGMII
The configuration of the OCTEONTX XCV_DLL_CTL register via
xcv_init_hw() is such that the RGMII RX delay is bypassed
leaving the RGMII TX delay enabled in the MAC:
The following pull-request contains BPF updates for your *net* tree.
We've added 15 non-merge commits during the last 10 day(s) which contain
a total of 12 files changed, 114 insertions(+), 31 deletions(-).
The main changes are:
1) Various BPF sockmap fixes related to RCU handling in the map's tear-
down code, from Jakub Sitnicki.
2) Fix macro state explosion in BPF sk_storage map when calculating its
bucket_log on allocation, from Martin KaFai Lau.
3) Fix potential BPF sockmap update race by rechecking socket's established
state under lock, from Lorenz Bauer.
4) Fix crash in bpftool on missing xlated instructions when kptr_restrict
sysctl is set, from Toke Høiland-Jørgensen.
5) Fix i40e's XSK wakeup code to return proper error in busy state and
various misc fixes in xdpsock BPF sample code, from Maciej Fijalkowski.
6) Fix the way modifiers are skipped in BTF in the verifier while walking
pointers to avoid program rejection, from Alexei Starovoitov.
7) Fix Makefile for runqslower BPF tool to i) rebuild on libbpf changes and
ii) to fix undefined reference linker errors for older gcc version due to
order of passed gcc parameters, from Yulia Kartseva and Song Liu.
8) Fix a trampoline_count BPF kselftest warning about missing braces around
initializer, from Andrii Nakryiko.
9) Fix up redundant "HAVE" prefix from large INSN limit kernel probe in
bpftool, from Michal Rostecki.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
powerpc: Fix CONFIG_TRACE_IRQFLAGS with CONFIG_VMAP_STACK
When CONFIG_PROVE_LOCKING is selected together with (now default)
CONFIG_VMAP_STACK, kernel enter deadlock during boot.
At the point of checking whether interrupts are enabled or not, the
value of MSR saved on stack is read using the physical address of the
stack. But at this point, when using VMAP stack the DATA MMU
translation has already been re-enabled, leading to deadlock.
Don't use the physical address of the stack when
CONFIG_VMAP_STACK is set.
The early versions of our kernel user access prevention (KUAP) were
written by Russell and Christophe, and didn't have separate
read/write access.
At some point I picked up the series and added the read/write access,
but I failed to update the usages in futex.h to correctly allow read
and write.
However we didn't notice because of another bug which was causing the
low-level code to always enable read and write. That bug was fixed
recently in commit 1d8f739b07bd ("powerpc/kuap: Fix set direction in
allow/prevent_user_access()").
futex_atomic_cmpxchg_inatomic() is passed the user address as %3 and
does:
Zenghui Yu [Thu, 6 Feb 2020 07:57:08 +0000 (15:57 +0800)]
irqchip/gic-v4.1: Ensure L2 vPE table is allocated at RD level
In GICv4, we will ensure that level2 vPE table memory is allocated
for the specified vpe_id on all v4 ITS, in its_alloc_vpe_table().
This still works well for the typical GICv4.1 implementation, where
the new vPE table is shared between the ITSs and the RDs.
To make it explicit, let us introduce allocate_vpe_l2_table() to
make sure that the L2 tables are allocated on all v4.1 RDs. We're
likely not need to allocate memory in it because the vPE table is
shared and (L2 table is) already allocated at ITS level, except
for the case where the ITS doesn't share anything (say SVPET == 0,
practically unlikely but architecturally allowed).
The implementation of allocate_vpe_l2_table() is mostly copied from
its_alloc_table_entry().
Zenghui Yu [Thu, 6 Feb 2020 07:57:07 +0000 (15:57 +0800)]
irqchip/gic-v4.1: Set vpe_l1_base for all redistributors
Currently, we will not set vpe_l1_page for the current RD if we can
inherit the vPE configuration table from another RD (or ITS), which
results in an inconsistency between RDs within the same CommonLPIAff
group.
Let's rename it to vpe_l1_base to indicate the base address of the
vPE configuration table of this RD, and set it properly for *all*
v4.1 redistributors.
Zenghui Yu [Thu, 6 Feb 2020 07:57:06 +0000 (15:57 +0800)]
irqchip/gic-v4.1: Fix programming of GICR_VPROPBASER_4_1_SIZE
The Size field of GICv4.1 VPROPBASER register indicates number of
pages minus one and together Page_Size and Size control the vPEID
width. Let's respect this requirement of the architecture.
mt76: mt7615: fix max_nss in mt7615_eeprom_parse_hw_cap
Fix u8 cast reading max_nss from MT_TOP_STRAP_STA register in
mt7615_eeprom_parse_hw_cap routine
Fixes: acf5457fd99db ("mt76: mt7615: read {tx,rx} mask from eeprom") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Linus Torvalds [Sat, 8 Feb 2020 01:59:07 +0000 (17:59 -0800)]
Merge tag 'fuse-fixes-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse
Pull fuse fixes from Miklos Szeredi:
- Fix a regression introduced in v5.1 that triggers WARNINGs for some
fuse filesystems
- Fix an xfstest failure
- Allow overlayfs to be used on top of fuse/virtiofs
- Code and documentation cleanups
* tag 'fuse-fixes-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: use true,false for bool variable
Documentation: filesystems: convert fuse to RST
fuse: Support RENAME_WHITEOUT flag
fuse: don't overflow LLONG_MAX with end offset
fix up iter on short count in fuse_direct_io()
Linus Torvalds [Sat, 8 Feb 2020 01:52:38 +0000 (17:52 -0800)]
Merge tag 'for-linus-5.6-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux
Pull orangefs fix from Mike Marshall:
"Debugfs fix for orangefs.
Vasliy Averin noticed that 'if seq_file .next function does not change
position index, read after some lseek can generate unexpected output'
and sent in this fix"
* tag 'for-linus-5.6-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux:
help_next should increase position index
Linus Torvalds [Sat, 8 Feb 2020 01:50:21 +0000 (17:50 -0800)]
Merge tag 'nfsd-5.6' of git://linux-nfs.org/~bfields/linux
Pull nfsd updates from Bruce Fields:
"Highlights:
- Server-to-server copy code from Olga.
To use it, client and both servers must have support, the target
server must be able to access the source server over NFSv4.2, and
the target server must have the inter_copy_offload_enable module
parameter set.
- Improvements and bugfixes for the new filehandle cache, especially
in the container case, from Trond
- Also from Trond, better reporting of write errors.
- Y2038 work from Arnd"
* tag 'nfsd-5.6' of git://linux-nfs.org/~bfields/linux: (55 commits)
sunrpc: expiry_time should be seconds not timeval
nfsd: make nfsd_filecache_wq variable static
nfsd4: fix double free in nfsd4_do_async_copy()
nfsd: convert file cache to use over/underflow safe refcount
nfsd: Define the file access mode enum for tracing
nfsd: Fix a perf warning
nfsd: Ensure sampling of the write verifier is atomic with the write
nfsd: Ensure sampling of the commit verifier is atomic with the commit
sunrpc: clean up cache entry add/remove from hashtable
sunrpc: Fix potential leaks in sunrpc_cache_unhash()
nfsd: Ensure exclusion between CLONE and WRITE errors
nfsd: Pass the nfsd_file as arguments to nfsd4_clone_file_range()
nfsd: Update the boot verifier on stable writes too.
nfsd: Fix stable writes
nfsd: Allow nfsd_vfs_write() to take the nfsd_file as an argument
nfsd: Fix a soft lockup race in nfsd_file_mark_find_or_create()
nfsd: Reduce the number of calls to nfsd_file_gc()
nfsd: Schedule the laundrette regularly irrespective of file errors
nfsd: Remove unused constant NFSD_FILE_LRU_RESCAN
nfsd: Containerise filecache laundrette
...
Linus Torvalds [Sat, 8 Feb 2020 01:39:56 +0000 (17:39 -0800)]
Merge tag 'nfs-for-5.6-1' of git://git.linux-nfs.org/projects/anna/linux-nfs
Puyll NFS client updates from Anna Schumaker:
"Stable bugfixes:
- Fix memory leaks and corruption in readdir # v2.6.37+
- Directory page cache needs to be locked when read # v2.6.37+
New features:
- Convert NFS to use the new mount API
- Add "softreval" mount option to let clients use cache if server goes down
- Add a config option to compile without UDP support
- Limit the number of inactive delegations the client can cache at once
- Improved readdir concurrency using iterate_shared()
Other bugfixes and cleanups:
- More 64-bit time conversions
- Add additional diagnostic tracepoints
- Check for holes in swapfiles, and add dependency on CONFIG_SWAP
- Various xprtrdma cleanups to prepare for 5.7's changes
- Several fixes for NFS writeback and commit handling
- Fix acls over krb5i/krb5p mounts
- Recover from premature loss of openstateids
- Fix NFS v3 chacl and chmod bug
- Compare creds using cred_fscmp()
- Use kmemdup_nul() in more places
- Optimize readdir cache page invalidation
- Lease renewal and recovery fixes"
* tag 'nfs-for-5.6-1' of git://git.linux-nfs.org/projects/anna/linux-nfs: (93 commits)
NFSv4.0: nfs4_do_fsinfo() should not do implicit lease renewals
NFSv4: try lease recovery on NFS4ERR_EXPIRED
NFS: Fix memory leaks
nfs: optimise readdir cache page invalidation
NFS: Switch readdir to using iterate_shared()
NFS: Use kmemdup_nul() in nfs_readdir_make_qstr()
NFS: Directory page cache pages need to be locked when read
NFS: Fix memory leaks and corruption in readdir
SUNRPC: Use kmemdup_nul() in rpc_parse_scope_id()
NFS: Replace various occurrences of kstrndup() with kmemdup_nul()
NFSv4: Limit the total number of cached delegations
NFSv4: Add accounting for the number of active delegations held
NFSv4: Try to return the delegation immediately when marked for return on close
NFS: Clear NFS_DELEGATION_RETURN_IF_CLOSED when the delegation is returned
NFSv4: nfs_inode_evict_delegation() should set NFS_DELEGATION_RETURNING
NFS: nfs_find_open_context() should use cred_fscmp()
NFS: nfs_access_get_cached_rcu() should use cred_fscmp()
NFSv4: pnfs_roc() must use cred_fscmp() to compare creds
NFS: remove unused macros
nfs: Return EINVAL rather than ERANGE for mount parse errors
...
That's one line (the assignment line) that is 2,686,974 characters in
length.
Now, sparse does happen to react particularly badly to that (I didn't
look to why, but I suspect it's just that evaluating all the types
that don't actually ever end up getting used ends up being much more
expensive than it should be), but I bet it's not good for gcc either.
Fixes: 6ac99e8f23d4 ("bpf: Introduce bpf sk local storage") Reported-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com> Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com> Link: https://lore.kernel.org/bpf/20200207081810.3918919-1-kafai@fb.com
Jakub Sitnicki [Thu, 6 Feb 2020 11:16:52 +0000 (12:16 +0100)]
selftests/bpf: Test freeing sockmap/sockhash with a socket in it
Commit 7e81a3530206 ("bpf: Sockmap, ensure sock lock held during tear
down") introduced sleeping issues inside RCU critical sections and while
holding a spinlock on sockmap/sockhash tear-down. There has to be at least
one socket in the map for the problem to surface.
This adds a test that triggers the warnings for broken locking rules. Not a
fix per se, but rather tooling to verify the accompanying fixes. Run on a
VM with 1 vCPU to reproduce the warnings.
Fixes: 7e81a3530206 ("bpf: Sockmap, ensure sock lock held during tear down") Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: John Fastabend <john.fastabend@gmail.com> Link: https://lore.kernel.org/bpf/20200206111652.694507-4-jakub@cloudflare.com
Jakub Sitnicki [Thu, 6 Feb 2020 11:16:51 +0000 (12:16 +0100)]
bpf, sockhash: Synchronize_rcu before free'ing map
We need to have a synchronize_rcu before free'ing the sockhash because any
outstanding psock references will have a pointer to the map and when they
use it, this could trigger a use after free.
This is a sister fix for sockhash, following commit 2bb90e5cc90e ("bpf:
sockmap, synchronize_rcu before free'ing map") which addressed sockmap,
which comes from a manual audit.
Fixes: 604326b41a6fb ("bpf, sockmap: convert to generic sk_msg interface") Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: John Fastabend <john.fastabend@gmail.com> Link: https://lore.kernel.org/bpf/20200206111652.694507-3-jakub@cloudflare.com
Jakub Sitnicki [Thu, 6 Feb 2020 11:16:50 +0000 (12:16 +0100)]
bpf, sockmap: Don't sleep while holding RCU lock on tear-down
rcu_read_lock is needed to protect access to psock inside sock_map_unref
when tearing down the map. However, we can't afford to sleep in lock_sock
while in RCU read-side critical section. Grab the RCU lock only after we
have locked the socket.
This fixes RCU warnings triggerable on a VM with 1 vCPU when free'ing a
sockmap/sockhash that contains at least one socket:
Fixes: 7e81a3530206 ("bpf: Sockmap, ensure sock lock held during tear down") Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: John Fastabend <john.fastabend@gmail.com> Link: https://lore.kernel.org/bpf/20200206111652.694507-2-jakub@cloudflare.com
bpftool: Don't crash on missing xlated program instructions
Turns out the xlated program instructions can also be missing if
kptr_restrict sysctl is set. This means that the previous fix to check the
jited_prog_insns pointer was insufficient; add another check of the
xlated_prog_insns pointer as well.
Fixes: 5b79bcdf0362 ("bpftool: Don't crash on missing jited insns or ksyms") Fixes: cae73f233923 ("bpftool: use bpf_program__get_prog_info_linear() in prog.c:do_dump()") Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Quentin Monnet <quentin@isovalent.com> Link: https://lore.kernel.org/bpf/20200206102906.112551-1-toke@redhat.com
Lorenz Bauer [Fri, 7 Feb 2020 10:37:12 +0000 (10:37 +0000)]
bpf, sockmap: Check update requirements after locking
It's currently possible to insert sockets in unexpected states into
a sockmap, due to a TOCTTOU when updating the map from a syscall.
sock_map_update_elem checks that sk->sk_state == TCP_ESTABLISHED,
locks the socket and then calls sock_map_update_common. At this
point, the socket may have transitioned into another state, and
the earlier assumptions don't hold anymore. Crucially, it's
conceivable (though very unlikely) that a socket has become unhashed.
This breaks the sockmap's assumption that it will get a callback
via sk->sk_prot->unhash.
Fix this by checking the (fixed) sk_type and sk_protocol without the
lock, followed by a locked check of sk_state.
Unfortunately it's not possible to push the check down into
sock_(map|hash)_update_common, since BPF_SOCK_OPS_PASSIVE_ESTABLISHED_CB
run before the socket has transitioned from TCP_SYN_RECV into
TCP_ESTABLISHED.
Fixes: 604326b41a6f ("bpf, sockmap: convert to generic sk_msg interface") Signed-off-by: Lorenz Bauer <lmb@cloudflare.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com> Link: https://lore.kernel.org/bpf/20200207103713.28175-1-lmb@cloudflare.com
Linus Torvalds [Fri, 7 Feb 2020 21:03:10 +0000 (13:03 -0800)]
Merge tag 'docs-5.6-2' of git://git.lwn.net/linux
Pull Documentation fixes from Jonathan Corbet:
"A handful of small documentation fixes that wandered in"
* tag 'docs-5.6-2' of git://git.lwn.net/linux:
Allow git builds of Sphinx
Documentation: changes.rst: update several outdated project URLs
Documentation: build warnings related to missing blank lines after explicit markups has been fixed
mailmap: add entry for Tiezhu Yang
Documentation/ko_KR/howto: Update a broken link
Documentation/ko_KR/howto: Update broken web addresses
docs/locking: Fix outdated section names
Linus Torvalds [Fri, 7 Feb 2020 20:51:54 +0000 (12:51 -0800)]
Merge tag 'acpi-5.6-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"Add Hisilicon Hip08-Lite I2C controller clock frequency support to the
ACPI driver for AMD SoCs (APD) and to the Designware I2C driver
(Hanjun Guo)"
* tag 'acpi-5.6-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
i2c: designware: Add ACPI HID for Hisilicon Hip08-Lite I2C controller
ACPI / APD: Add clock frequency for Hisilicon Hip08-Lite I2C controller
Linus Torvalds [Fri, 7 Feb 2020 20:49:10 +0000 (12:49 -0800)]
Merge tag 'pm-5.6-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
- Update the recently merged CPR (Core Power Reduction) support in the
AVS (Adaptive Voltage Scaling) subsystem (Brendan Higgins, Nathan
Chancellor, Niklas Cassel)
- Update the rockchip-io AVS driver (Heiko Stuebner)
- Add two more module parameters to intel_idle on top of the recently
merged material (Rafael Wysocki)
- Clean up a piece of cpuidle documentation and consolidate system
sleep states documentation (Rafael Wysocki)
* tag 'pm-5.6-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpuidle: Documentation: Clean up PM QoS description
Documentation: admin-guide: PM: Update sleep states documentation
intel_idle: Introduce 'states_off' module parameter
intel_idle: Introduce 'use_acpi' module parameter
power: avs: qcom-cpr: Avoid clang -Wsometimes-uninitialized in cpr_scale
power: avs: qcom-cpr: add unspecified HAS_IOMEM dependency
PM / AVS: rockchip-io: fix the supply naming for the emmc supply on px30
power: avs: qcom-cpr: add a printout after the driver has been initialized
projects / mirror_ubuntu-kernels.git / log