V4L/DVB: dvb-usb: prepare drivers for using rc-core
This is a big patch, yet trivial. It just move the RC properties
to a separate struct, in order to prepare the dvb-usb drivers to
use rc-core. There's no change on the behavior of the drivers.
With this change, it is possible to have both legacy and rc-core
based code inside the dvb-usb-remote, allowing a gradual migration
to rc-core, driver per driver.
V4L/DVB: dvb-usb: get rid of struct dvb_usb_rc_key
dvb-usb has its own IR handle code. Now that we have a Remote
Controller subsystem, we should start using it. So, remove this
struct, in favor of the similar struct defined at the RC subsystem.
This is a big, but trivial patch. It is a 3 line delect, plus
lots of rename on several dvb-usb files.
V4L/DVB: V4L2: sh_vou: VOU does support the full PAL resolution too
SH7724 datasheet specifies 480 pixels as the VOU maximum vertical resolution.
This is a bug in the datasheet, VOU also supports the full PAL resolution: 576
lines. Adjust the driver accordingly.
V4L/DVB: V4L2: sh_mobile_camera_ceu: add support for CSI2
Using CEU with CSI2 on SH-Mobile requires some special configuration of the
former. We also have to switch from calling only one subdev .s_mbus_fmt and
.try_mbus_fmt to calling all subdevices. Take care to increment CSI2 driver
use count to prevent it from unloading, while in use.
V4L/DVB: V4L2: soc-camera: add a MIPI CSI-2 driver for SH-Mobile platforms
Some SH-Mobile SoCs implement a MIPI CSI-2 controller, that can interface to
several video clients and send data to the CEU or to the Image Signal
Processor. This patch implements a v4l2-subdevice driver for CSI-2 to be used
within the soc-camera framework, implementing the second subdevice in addition
to the actual video clients.
Endianness notation is meaningless for 8 bit YUYV codes. Switch pixel code
names to explicitly state the order of colour components in the data
stream.
Jarod Wilson [Mon, 26 Jul 2010 23:29:43 +0000 (20:29 -0300)]
V4L/DVB: staging/lirc: add lirc_imon driver
Nb: this is a very trimmed-down lirc_imon, which only supports the
oldest generation of imon devices that don't do onboard signal decoding
like the most recent generation imon devices -- those are now supported
by the ir-core imon driver.
Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jarod Wilson [Mon, 26 Jul 2010 23:27:55 +0000 (20:27 -0300)]
V4L/DVB: staging/lirc: add lirc_ene0100 driver
[mchehab@redhat.com: fixed a few WARNING: please, no space before tabs] Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jarod Wilson [Sun, 7 Mar 2010 20:55:43 +0000 (17:55 -0300)]
V4L/DVB: dvb: add support for kworld 340u and ub435-q to em28xx-dvb
This adds support for the KWorld PlusTV 340U and KWorld UB345-Q ATSC
sticks, which are really the same device. The sticks have an eMPIA
em2870 usb bridge chipset, an LG Electronics LGDT3304 ATSC/QAM
demodulator and an NXP TDA18271HD tuner -- early versions of the 340U
have a a TDA18271HD/C1, later models and the UB435-Q have a C2.
The stick has been tested succesfully with both VSB_8 and QAM_256 signals.
Its using lgdt3304 support added to the lgdt3305 driver by a prior patch,
rather than the current lgdt3304 driver, as its severely lacking in
functionality by comparison (see said patch for details).
Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L/DVB: uvc: Move constants and structures definitions to linux/usb/video.h
The UVC host and gadget drivers both define constants and structures in
private header files. Move all those definitions to linux/usb/video.h
where they can be shared by the two drivers (and be available for
userspace applications).
Antti Palosaari [Wed, 16 Jun 2010 19:43:40 +0000 (16:43 -0300)]
V4L/DVB: af9013: program tuner before demodulator
Program tuner before demodulator in case of channel set. Earlier it was
programmed during demodulator programming. This seems to resolve weird
error where demodulator misses sometimes ability to gain lock.
Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L/DVB: gspca - sonixj: Do the audio input work for webcams with a microphone
The bit 0x04 of the bridge register 02 (GPIO) is used for audio connection
in webcams containing the bridge SN9C105. This patch sets it correctly,
according to the presence of an audio device.
This function has sanity checks to make sure that "dev" is non-null. I
moved the dereference down below the checks. In the current code "dev"
is never actually null.
Stanse found that in ivtvfb_callback_cleanup and ivtvfb_callback_init
there are unneeded tests for itv being NULL. But itv is initialized
as container_of with non-zero offset in those functions, so it is
never NULL (even if v4l2_dev is). This was found because itv is
dereferenced earlier than the test.
Jarod Wilson [Fri, 16 Jul 2010 17:25:33 +0000 (14:25 -0300)]
V4L/DVB: IR/lirc: make lirc userspace and staging modules buildable
The lirc userspace needs all the current ioctls defined, and we need to
put the header files in places out-of-tree and/or staging lirc drivers
(which I plan to prep soon) can easily build with. I've actually tested this
in a tree w/all the lirc drivers queued up to be submitted for staging. I'm
also reasonably sure that Andy Walls is going to need most of the ioctls
anyway for his cx23888 IR driver work.
Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L/DVB: drivers/media/video: Remove dead CONFIG_FB_OMAP2_FORCE_AUTO_UPDATE
CONFIG_FB_OMAP2_FORCE_AUTO_UPDATE doesn't exist in Kconfig and is never defined anywhere
else, therefore removing all references for it from the source code.
Signed-off-by: Christian Dietrich <qy03fugy@stud.informatik.uni-erlangen.de> Acked-by: Vaibhav Hiremath <hvaibhav@ti.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L/DVB: gspca - main: Don't use the frame buffer flags
This patch fixes possible race conditions in queue management with SMP:
when a frame was completed, the irq function tried to use the next frame
buffer. At this time, it was possible that the application on an other
processor updated the frame pointer, making the image to point to a bad
buffer.
The patch contains two main changes:
- the image transfer uses the queue indexes which are protected against
simultaneous memory access,
- the image pointer which is used for image concatenation is only set at
interrupt level.
Some subdrivers which used the image pointer have been updated.
Reported-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jean-François Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L/DVB: gspca - main: Possible race condition in queue management
The problem may occur with SMP:
- a frame is completed at interrupt level (in gspca_frame_add with
packet_type == LAST_PACKET,
- just after clearing the bit V4L2_BUF_FLAG_QUEUED and before setting
the bit V4L2_BUF_FLAG_DONE, on the other processor, the application
tries to requeue the same frame buffer,
- then, the qbuf function succeeds because ALL_FLAGS are not set.
The fix sets and resets the two flags in one instruction.
Reported-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jean-François Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Christoph Egger [Fri, 15 Jan 2010 11:49:41 +0000 (08:49 -0300)]
V4L/DVB: remove obsolete conditionalizing on DVB_DIBCOM_DEBUG
As pointed by Christoph Egger <siccegge@stud.informatik.uni-erlangen.de>,
The config Option DVB_DIBCOM_DEBUG was dropped while removing the dibusb
driver in favor of dvb-usb in 2005. However it remaind existant at some
places of the kernel config.
Instead of just removing the debug capability, the better is to just remove
the bad dependency, making the modprobe function always visible.
Thanks-to: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L/DVB: si470x: -EINVAL overwritten in si470x_vidioc_s_tuner()
This patch to the si470x_vidioc_s_tuner function was developed in
cooperation with Roel Kluin <roel.kluin@gmail.com>. It sets the default
retval to 0 instead of -EINVAL, identical to what is done in all other
set/get functions of v4l2_ioctl_ops. This is just as cosmetic change, as
retval is directly overwritten by the si470x_disconnect_check() anyway.
Jarod Wilson [Thu, 8 Jul 2010 15:38:57 +0000 (12:38 -0300)]
V4L/DVB: IR/mceusb: more streamlining of device init
Spent a while last night getting device initialization packet captures
under Windows for all generations of devices. There are a few places
where we were doing things differently, and few things we were doing
that we don't need to do, particularly on gen3 hardware, and I *think*
one of those things is what was locking up my pinnacle hw from time to
time -- at least, its been perfectly well behaved every time its been
plugged in since making this change.
First up, we're adding a bit more to the gen1 init routine here. Its
not absolutely necessary, the hardware works the same both with and
without it, but I'd like to be consistent w/Windows here.
Second, DEVICE_RESET is never called when initializing either of my
gen3 devices, its only called for gen1 and gen2. The bits in the gen3
init after removing that, are safe (and interesting) to run on all
hardware, so there's no more gen3-specific init done, there's instead
a generic mceusb_get_parameters() that is run for all hardware.
Third, the gen3 flag isn't needed. We only care if hardware is gen3
during probe, so I've dropped that from the device flags struct.
Successfully tested on all three generations of mceusb hardware.
Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jarod Wilson [Wed, 7 Jul 2010 14:29:44 +0000 (11:29 -0300)]
V4L/DVB: IR/lirc_dev: fix locking in lirc_dev_fop_read
On Wed, Jul 07, 2010 at 02:52:58PM +0200, Jiri Slaby wrote:
> Hi,
>
> stanse found a locking error in lirc_dev_fop_read:
> if (mutex_lock_interruptible(&ir->irctl_lock))
> return -ERESTARTSYS;
> ...
> while (written < length && ret == 0) {
> if (mutex_lock_interruptible(&ir->irctl_lock)) { #1
> ret = -ERESTARTSYS;
> break;
> }
> ...
> }
>
> remove_wait_queue(&ir->buf->wait_poll, &wait);
> set_current_state(TASK_RUNNING);
> mutex_unlock(&ir->irctl_lock); #2
>
> If lock at #1 fails, it beaks out of the loop, with the lock unlocked,
> but there is another "unlock" at #2.
This should do the trick. Completely untested beyond compiling, but its
not exactly a complicated fix, and in practice, I'm not aware of anyone
ever actually tripping that locking bug, so there's zero functional change
in typical use here.
Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since commit b4028437876866aba4747a655ede00f892089e14
the 'driver_data' field resides in device's struct device_private
which may be allocated by dev_set_drvdata() if device_private
struct was not allocated previously.
dev_set_drvdata() is used in video_set_drvdata() to set
the driver's private data pointer in v4l2 drivers. Setting
the private data _before_ registering the v4l2 device results
in a memory leak since __video_register_device() also calls
video_set_drvdata(), but after zeroing the device structure.
Thus, the reference to the previously allocated device_private
struct goes lost and a new device_private will be allocated.
All v4l drivers which call video_set_drvdata() _before_
calling video_register_device() are affected. The patch fixes
__video_register_device() to preserve previously allocated
device_private reference.
V4L/DVB: tda10048: fix the uncomplete function tda10048_read_ber
Completes the bit-error-rate read function with the CBER register (before
Viterbi decoder). The returned value is 1e8*actual_ber to be positive.
Also includes some typo mistakes.
Jarod Wilson [Sun, 4 Jul 2010 01:42:14 +0000 (22:42 -0300)]
V4L/DVB: IR/mceusb: unify and simplify different gen device init
Started out as an effort to try to tackle the last remaining issue I'm
having with this damned pinnacle device getting wedged the first time
its plugged in after an indeterminate length of not being plugged in.
Didn't get that solved yet, but did streamline the init code a bit more
and remove some superfluous gunk. Nukes a completely unneeded call to
usb_device_init() and several lines of overly complex crap in the gen1
device init path.
Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L/DVB: v4l: Add MPC5121e VIU video capture driver
Adds support for Video-In (VIU) unit of Freescale
MPC5121e. The driver supports RGB888/RGB565 formats,
capture and overlay on MPC5121e DIU frame buffer.
Laurent Pinchart [Fri, 18 Jun 2010 14:31:24 +0000 (11:31 -0300)]
V4L/DVB: uvcvideo: Don't use stack-based buffers for USB transfers
Data buffers on the stack are not allowed for USB I/O. Use dynamically
allocated buffers instead when querying control length and control
capabilities.
The control capabilities are now also stored in the uvc_control
structure.
Laurent Pinchart [Thu, 18 Feb 2010 19:38:52 +0000 (16:38 -0300)]
V4L/DVB: uvcvideo: Support menu controls in the control mapping API
The UVCIOC_CTRL_MAP ioctl doesn't support menu entries for menu
controls. As the uvc_xu_control_mapping structure has no reserved
fields, this can't be fixed while keeping ABI compatibility.
Modify the UVCIOC_CTRL_MAP ioctl to add menu entries support, and define
UVCIOC_CTRL_MAP_OLD that supports the old ABI without any ability to add
menu controls.
Hans de Goede [Wed, 19 May 2010 23:15:00 +0000 (20:15 -0300)]
V4L/DVB: uvcvideo: Make button controls work properly
According to the v4l2 spec, writing any value to a button control should
result in the action belonging to the button control being triggered.
UVC cams however want to see a 1 written, this patch fixes this by
overriding whatever value user space passed in with -1 (0xffffffff) when
the control is a button control.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean Delvare [Mon, 28 Jun 2010 15:59:49 +0000 (12:59 -0300)]
V4L/DVB: cx88: Let the user disable IR support
It might be useful to be able to disable the IR support, either for
debugging purposes, or just for users who know they won't use the IR
remote control anyway. On many cards, IR support requires expensive
polling/sampling which is better avoided if never needed.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean Delvare [Mon, 28 Jun 2010 15:55:43 +0000 (12:55 -0300)]
V4L/DVB: cx88: Move I2C IR initialization
Move I2C IR initialization from just after I2C bus setup to right
before non-I2C IR initialization. This is the same as was done for
the bttv driver several months ago. Might solve bugs which have not yet
been reported for some cards. It makes both drivers consistent, and
makes it easier to disable IR support (coming soon.)
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/common/tuners/xc5000.c: In function ‘xc_write_reg’:
drivers/media/common/tuners/xc5000.c:298: warning: passing argument 3 of ‘xc5000_readreg’ from incompatible pointer type
drivers/media/common/tuners/xc5000.c:235: note: expected ‘u16 *’ but argument is of type ‘u8 *’
drivers/media/common/tuners/xc5000.c: At top level:
drivers/media/common/tuners/xc5000.c:223: warning: ‘xc_read_i2c_data’ defined but not used
Andy Walls [Mon, 28 Jun 2010 02:15:35 +0000 (23:15 -0300)]
V4L/DVB: cx23885: Convert cx23885-input to use new in kernel IR pulse decoders
Convert the cx23885 driver to use the new in kernel IR pulse
decoders for the integrated CX2388[578] IR controllers. Rip out a lot
of RC-5 decoding related code in the process and rename some variables
for clarity or to more accurately describe their usage.
Signed-off-by: Andy Walls <awalls@md.metrocast.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Sun, 27 Jun 2010 20:17:06 +0000 (17:17 -0300)]
V4L/DVB: cx23885: Convert from struct card_ir to struct cx23885_ir_input for IR Rx
Move from the generic, shared card_ir state structure to a cx23885 driver
specific IR state structure in anticipation of moving to the new IR pulse
decoders in the IR core.
Fix up the card name truncation in the dmesg log while we're at it,
by avoiding using fixed length string storage in our new IR state
structure.
Signed-off-by: Andy Walls <awalls@md.metrocast.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The image pointer and its length are now in the main structure instead
of in the frame buffer. They are updated on application vidioc_qbuf and
in the URB interrupt function when ending an image.
Vaibhav Hiremath [Sat, 12 Jun 2010 12:09:56 +0000 (09:09 -0300)]
V4L/DVB: vpfe_capture: Create separate Kconfig file for davinci devices
Currently VPFE Capture driver and DM6446 CCDC driver is being
reused for AM3517. So this patch is preparing the Kconfig/makefile
for re-use of such IP's.
V4L/DVB: tuners:tuner-simple Fix warning: variable 'tun' set but not used
Resend due to a whitespace issue I created by mistake.
The below patch fixes a warning message create by gcc 4.6.0
CC [M] drivers/media/common/tuners/tuner-simple.o
drivers/media/common/tuners/tuner-simple.c: In function 'simple_set_tv_freq':
drivers/media/common/tuners/tuner-simple.c:548:20: warning: variable 'tun' set but not used
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dan Carpenter [Fri, 4 Jun 2010 15:39:03 +0000 (12:39 -0300)]
V4L/DVB: dvb_ca_en50221: return -EFAULT on copy_to_user errors
copy_to_user() returns the number of bytes remaining to be copied which
isn't the right thing to return here. The comments say that these
functions in dvb_ca_en50221.c should return the number of bytes copied or
an error return. I've changed it to return -EFAULT.
Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dan Carpenter [Fri, 4 Jun 2010 10:34:40 +0000 (07:34 -0300)]
V4L/DVB: media/radio: fix copy_to_user to user handling
copy_to/from_user() returns the number of bytes remaining to be copied
but the code here was testing for negative returns. I modified it to
return -EFAULT. These functions are called from si4713_s_ext_ctrls() and
that only tests for negative error codes.
Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
projects / mirror_ubuntu-kernels.git / log