This might matter, for example, if the underlying type of enum xz_check
was a signed char. In such a case the validation wouldn't have caught an
unsupported header. I don't know if this problem can occur in the kernel
on any arch but it's still good to fix it because some people might copy
the XZ code to their own projects from Linux instead of the upstream
XZ Embedded repository.
This change may increase the code size by a few bytes. An alternative
would have been to use an unsigned int instead of enum xz_check but
using an enumeration looks cleaner.
With valid files, the safety margin described in lib/decompress_unxz.c
ensures that these buffers cannot overlap. But if the uncompressed size
of the input is larger than the caller thought, which is possible when
the input file is invalid/corrupt, the buffers can overlap. Obviously
the result will then be garbage (and usually the decoder will return
an error too) but no other harm will happen when such an over-run occurs.
This change only affects uncompressed LZMA2 chunks and so this
should have no effect on performance.
For files that lack trailing newlines and match a leaking address (e.g.
wchan[1]), the leaking_addresses.pl report would run together with the
next line, making things look corrupted.
Unconditionally remove the newline on input, and write it back out on
output.
Some buggy firmware and/or brand new batteries can support a charge that's
slightly over the reported design capacity. In such cases, the kernel will
report to userspace that the charging state of the battery is "Unknown",
when in reality the battery charge is "Full", at least from the design
capacity point of view. Make the fallback condition accepts capacities
over the designed capacity so userspace knows that is full.
Signed-off-by: André Almeida <andrealmeid@collabora.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Both iov_iter_get_pages and iov_iter_get_pages_alloc return the number
of bytes of the iovec they could get the pages for. When they cannot
get any pages, they're supposed to return 0, but when the start of the
iovec isn't page aligned, the calculation goes wrong and they return a
negative value. Fix both functions.
In addition, change iov_iter_get_pages_alloc to return NULL in that case
to prevent resource leaks.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
kzalloc() is used to allocate memory for cd->detectors, and if it fails,
channel_detector_exit() behind the label fail will be called:
channel_detector_exit(dpd, cd);
In channel_detector_exit(), cd->detectors is dereferenced through:
struct pri_detector *de = cd->detectors[i];
To fix this possible null-pointer dereference, check cd->detectors before
the for loop to dereference cd->detectors.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn> Signed-off-by: Tuo Li <islituo@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210805153854.154066-1-islituo@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The tracefs file system is by default mounted such that only root user can
access it. But there are legitimate reasons to create a group and allow
those added to the group to have access to tracing. By changing the
permissions of the tracefs mount point to allow access, it will allow
group access to the tracefs directory.
There should not be any real reason to allow all access to the tracefs
directory as it contains sensitive information. Have the default
permission of directories being created not have any OTH (other) bits set,
such that an admin that wants to give permission to a group has to first
disable all OTH bits in the file system.
Link: https://lkml.kernel.org/r/20210818153038.664127804@goodmis.org Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Due to deadlocks in the networking subsystem spotted 12 years ago[1],
a workaround was put in place[2] to avoid taking the rtnl lock when it
was not available and restarting the syscall (back to VFS, letting
userspace spin). The following construction is found a lot in the net
sysfs and sysctl code:
if (!rtnl_trylock())
return restart_syscall();
This can be problematic when multiple userspace threads use such
interfaces in a short period, making them to spin a lot. This happens
for example when adding and moving virtual interfaces: userspace
programs listening on events, such as systemd-udevd and NetworkManager,
do trigger actions reading files in sysfs. It gets worse when a lot of
virtual interfaces are created concurrently, say when creating
containers at boot time.
Returning early without hitting the above pattern when the syscall will
fail eventually does make things better. While it is not a fix for the
issue, it does ease things.
[1] https://lore.kernel.org/netdev/49A4D5D5.5090602@trash.net/
https://lore.kernel.org/netdev/m14oyhis31.fsf@fess.ebiederm.org/
and https://lore.kernel.org/netdev/20090226084924.16cb3e08@nehalam/
[2] Rightfully, those deadlocks are *hard* to solve.
Signed-off-by: Antoine Tenart <atenart@kernel.org> Reviewed-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
In dibusb_read_eeprom_byte(), if dibusb_i2c_msg() fails, val gets
assigned an value that's not properly initialized.
Using kzalloc() in place of kmalloc() for the buffer fixes this issue,
as the val can now be set to 0 in the event dibusb_i2c_msg() fails.
Reported-by: syzbot+e27b4fd589762b0b9329@syzkaller.appspotmail.com Tested-by: syzbot+e27b4fd589762b0b9329@syzkaller.appspotmail.com Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
During wakeup from system-wide sleep states, acpi_get_sleep_type_data()
is called and it tries to get memory from the slab allocator in order
to evaluate a control method, but if KFENCE is enabled in the kernel,
the memory allocation attempt causes an IRQ work to be queued and a
self-IPI to be sent to the CPU running the code which requires the
memory controller to be ready, so if that happens too early in the
wakeup path, it doesn't work.
Prevent that from taking place by calling acpi_get_sleep_type_data()
for S0 upfront, when preparing to enter a given sleep state, and
saving the data obtained by it for later use during system wakeup.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214271 Reported-by: Reik Keutterling <spielkind@gmail.com> Tested-by: Reik Keutterling <spielkind@gmail.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
If rcsi2_code_to_fmt() return NULL, then null pointer dereference occurs
in the next cycle. That should not be possible now but adding checking
protects from future bugs.
The patch adds checking if format is NULL.
Found by Linux Driver Verification project (linuxtesting.org).
The Cyberbook T116 tablet contains quite generic names in the sys_vendor
and product_name DMI strings, without this patch brcmfmac will try to load:
"brcmfmac43455-sdio.Default string-Default string.txt" as nvram file which
is way too generic.
The nvram file shipped on the factory Android image contains the exact
same settings as those used on the AcePC T8 mini PC, so point the new
DMI nvram filename quirk to the acepc-t8 nvram file.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210928160633.96928-1-hdegoede@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
When CONFIG_PRINTK is not set, the CMPXCHG_BUGCHECK() macro calls
_printk(), but _printk() is a static inline function, not available
as an extern.
Since the purpose of the macro is to print the BUGCHECK info,
make this config option depend on PRINTK.
Fixes multiple occurrences of this build error:
../include/linux/printk.h:208:5: error: static declaration of '_printk' follows non-static declaration
208 | int _printk(const char *s, ...)
| ^~~~~~~
In file included from ../arch/ia64/include/asm/cmpxchg.h:5,
../arch/ia64/include/uapi/asm/cmpxchg.h:146:28: note: previous declaration of '_printk' with type 'int(const char *, ...)'
146 | extern int _printk(const char *fmt, ...);
Cc: linux-ia64@vger.kernel.org Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Tony Luck <tony.luck@intel.com> Cc: Chris Down <chris@chrisdown.name> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Petr Mladek <pmladek@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Syzkaller reported a warning called "rcu detected stall in dummy_timer".
The error seems to be an error in mceusb_dev_recv(). In the case of
-EPROTO error, the routine immediately resubmits the URB. Instead it
should return without resubmitting URB.
Reported-by: syzbot+4d3749e9612c2cfab956@syzkaller.appspotmail.com Signed-off-by: Rajat Asthana <rajatasthana4@gmail.com> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Some tools like v4l2-compliance let users select a media device based
on the bus_info string which can be quite convenient. Use a unique
string for that.
This also fixes the following v4l2-compliance warning:
warn: v4l2-test-media.cpp(52): empty bus_info
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The variable pdev is assigned to dev->plat_dev, and dev->plat_dev is
checked in:
if (!dev->plat_dev)
This indicates both dev->plat_dev and pdev can be NULL. If so, the
function dev_err() is called to print error information.
dev_err(&pdev->dev, "No platform data specified\n");
However, &pdev->dev is an illegal address, and it is dereferenced in
dev_err().
To fix this possible null-pointer dereference, replace dev_err() with
mfc_err().
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn> Signed-off-by: Tuo Li <islituo@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The device is doing something unexpected with the control. Either because
the protocol is not properly implemented or there has been a HW error.
Fixes v4l2-compliance:
Control ioctls (Input 0):
fail: v4l2-test-controls.cpp(448): s_ctrl returned an error (22)
test VIDIOC_G/S_CTRL: FAIL
fail: v4l2-test-controls.cpp(698): s_ext_ctrls returned an error (22)
test VIDIOC_G/S/TRY_EXT_CTRLS: FAIL
there is still uninitialized field sd_format of struct stm32_dcmi *dcmi.
If an interrupt occurs in the interval between the installation of the
interrupt handler and the initialization of this field, NULL pointer
dereference happens.
This field is dereferenced in the handler function without any check:
The patch moves interrupt handler installation
after initialization of the sd_format field that happens in
dcmi_graph_notify_complete() via dcmi_set_default_fmt().
Found by Linux Driver Verification project (linuxtesting.org).
The interrupt handling should be related to the firmware version. If
the driver matches an old firmware, then the driver should not handle
interrupt such as i2c or dma, otherwise it will cause some errors.
Beacon buffer for high latency devices does not use DMA. other similar
buffer allocation methods in the driver have already been modified for
high latency path. Fix the beacon buffer allocation left out in the
earlier high latency changes.
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com> Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
[fabio: adapt it to use ar->bus_param.dev_type ] Signed-off-by: Fabio Estevam <festevam@denx.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210818232627.2040121-1-festevam@denx.de Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
When creating a new virtual interface in mwifiex_add_virtual_intf(), we
update our internal driver states like bss_type, bss_priority, bss_role
and bss_mode to reflect the mode the firmware will be set to.
When switching virtual interface mode using
mwifiex_init_new_priv_params() though, we currently only update bss_mode
and bss_role. In order for the interface mode switch to actually work,
we also need to update bss_type to its proper value, so do that.
This fixes a crash of the firmware (because the driver tries to execute
commands that are invalid in AP mode) when switching from station mode
to AP mode.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210914195909.36035-9-verdre@v0yd.nl Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
We currently handle changing from the P2P to the STATION virtual
interface type slightly different than changing from P2P to ADHOC: When
changing to STATION, we don't send the SET_BSS_MODE command. We do send
that command on all other type-changes though, and it probably makes
sense to send the command since after all we just changed our BSS_MODE.
Looking at prior changes to this part of the code, it seems that this is
simply a leftover from old refactorings.
Since sending the SET_BSS_MODE command is the only difference between
mwifiex_change_vif_to_sta_adhoc() and the current code, we can now use
mwifiex_change_vif_to_sta_adhoc() for both switching to ADHOC and
STATION interface type.
This does not fix any particular bug and just "looked right", so there's
a small chance it might be a regression.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210914195909.36035-4-verdre@v0yd.nl Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
It turns out that a single page of stack is trivial to overflow with
all the tracing gunk enabled. Raise the exception stacks to 2 pages,
which is still half the interrupt stacks, which are at 4 pages.
Reported-by: Michael Wang <yun.wang@linux.alibaba.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/YUIO9Ye98S5Eb68w@hirez.programming.kicks-ass.net Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Syzkaller reported use-after-free bug as described in [1]. The bug is
triggered when smk_set_cipso() tries to free stale category bitmaps
while there are concurrent reader(s) using the same bitmaps.
Wait for RCU grace period to finish before freeing the category bitmaps
in smk_set_cipso(). This makes sure that there are no more readers using
the stale bitmaps and freeing them should be safe.
mq / mqprio make the default child qdiscs visible. They only do
so for the qdiscs which are within real_num_tx_queues when the
device is registered. Depending on order of calls in the driver,
or if user space changes config via ethtool -L the number of
qdiscs visible under tc qdisc show will differ from the number
of queues. This is confusing to users and potentially to system
configuration scripts which try to make sure qdiscs have the
right parameters.
Add a new Qdisc_ops callback and make relevant qdiscs TTRT.
Note that this uncovers the "shortcut" created by
commit 1f27cde313d7 ("net: sched: use pfifo_fast for non real queues")
The default child qdiscs beyond initial real_num_tx are always
pfifo_fast, no matter what the sysfs setting is. Fixing this
gets a little tricky because we'd need to keep a reference
on whatever the default qdisc was at the time of creation.
In practice this is likely an non-issue the qdiscs likely have
to be configured to non-default settings, so whatever user space
is doing such configuration can replace the pfifos... now that
it will see them.
Reported-by: Matthew Massey <matthewmassey@fb.com> Reviewed-by: Dave Taht <dave.taht@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Different SoCs have a different number of channels, e.g .:
* amazon-se has 10 channels,
* danube+ar9 have 20 channels,
* vr9 has 28 channels,
* ar10 has 24 channels.
We can read the ID register and, depending on the reported
number of channels, reset the appropriate number of channels.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Reading the DMA registers immediately after the reset causes
Data Bus Error. Adding a small delay fixes this issue.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Previously, `__query_block()` would fail if the
second WCxx method call failed. However, the
WQxx method might have succeeded, and potentially
allocated memory for the result. Instead of
throwing away the result and potentially
leaking memory, ignore the result of
the second WCxx call.
Signed-off-by: Barnabás Pőcze <pobrn@protonmail.com> Link: https://lore.kernel.org/r/20210904175450.156801-25-pobrn@protonmail.com Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Signed-off-by: Simon Ser <contact@emersion.fr> Cc: Jared Baldridge <jrb@expunge.us> Cc: Emil Velikov <emil.l.velikov@gmail.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Hans de Goede <hdegoede@redhat.com> Acked-by: Sam Ravnborg <sam@ravnborg.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210911102430.253986-1-contact@emersion.fr Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Once l2cap_sock_teardown_cb() excuted, this sock will be marked as SOCK_ZAPPED,
and can be treated as killable in l2cap_sock_kill() if sock_orphan() has
excuted, at this time we close sock through sock_close() which end to call
l2cap_sock_kill() like Thread C:
Context: Thread C:
sock_close()
l2cap_sock_release()
sock_orphan()
l2cap_sock_kill() #free sock if refcnt is 1
If C completed, Once A or B reaches l2cap_sock_teardown_cb() again,
use-after-free happened.
We should set chan->data to NULL if sock is destructed, for telling teardown
operation is not allowed in l2cap_sock_teardown_cb(), and also we should
avoid killing an already killed socket in l2cap_sock_close_cb().
Signed-off-by: Wang ShaoBo <bobo.shaobowang@huawei.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The sco_send_frame() also takes lock_sock() during memcpy_from_msg()
call that may be endlessly blocked by a task with userfaultd
technique, and this will result in a hung task watchdog trigger.
Just like the similar fix for hci_sock_sendmsg() in commit 92c685dc5de0 ("Bluetooth: reorganize functions..."), this patch moves
the memcpy_from_msg() out of lock_sock() for addressing the hang.
This should be the last piece for fixing CVE-2021-3640 after a few
already queued fixes.
2 improvements to the Lenovo Ideapad D330 panel-orientation quirks:
1. Some versions of the Lenovo Ideapad D330 have a DMI_PRODUCT_NAME of
"81H3" and others have "81MD". Testing has shown that the "81MD" also has
a 90 degree mounted panel. Drop the DMI_PRODUCT_NAME from the existing
quirk so that the existing quirk matches both variants.
2. Some of the Lenovo Ideapad D330 models have a HD (800x1280) screen
instead of a FHD (1200x1920) screen (both are mounted right-side-up) add
a second Lenovo Ideapad D330 quirk for the HD version.
Changes in v2:
- Add a new quirk for Lenovo Ideapad D330 models with a HD screen instead
of a FHD screen
It is expected from the clients to follow the below steps on an imported
dmabuf fd:
a) dmabuf = dma_buf_get(fd) // Get the dmabuf from fd
b) dma_buf_attach(dmabuf); // Clients attach to the dmabuf
o Here the kernel does some slab allocations, say for
dma_buf_attachment and may be some other slab allocation in the
dmabuf->ops->attach().
c) Client may need to do dma_buf_map_attachment().
d) Accordingly dma_buf_unmap_attachment() should be called.
e) dma_buf_detach () // Clients detach to the dmabuf.
o Here the slab allocations made in b) are freed.
f) dma_buf_put(dmabuf) // Can free the dmabuf if it is the last
reference.
Now say an erroneous client failed at step c) above thus it directly
called dma_buf_put(), step f) above. Considering that it may be the last
reference to the dmabuf, buffer will be freed with pending attachments
left to the dmabuf which can show up as the 'memory leak'. This should
at least be reported as the WARN().
Signed-off-by: Charan Teja Reddy <charante@codeaurora.org> Reviewed-by: Christian König <christian.koenig@amd.com> Link: https://patchwork.freedesktop.org/patch/msgid/1627043468-16381-1-git-send-email-charante@codeaurora.org Signed-off-by: Christian König <christian.koenig@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Chipidea core was calling the interrupt handler from non-IRQ context
with interrupts enabled, something which can lead to a deadlock if
there's an actual interrupt trying to take a lock that's already held
(e.g. the controller lock in udc_irq()).
Add a wrapper that can be used to fake interrupts instead of calling the
handler directly.
Fixes: 3ecb3e09b042 ("usb: chipidea: Use extcon framework for VBUS and ID detect") Fixes: 876d4e1e8298 ("usb: chipidea: core: add wakeup support for extcon") Cc: Peter Chen <peter.chen@kernel.org> Cc: stable@vger.kernel.org # 4.4 Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20211021083447.20078-1-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
If keyspan_port_probe() fails to allocate memory for an out_buffer[i] or
in_buffer[i], the previously allocated memory for out_buffer or
in_buffer needs to be freed on the error handling path, otherwise a
memory leak will result.
Fixes: bad41a5bf177 ("USB: keyspan: fix port DMA-buffer allocations") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Link: https://lore.kernel.org/r/20211015085543.1203011-1-wanghai38@huawei.com Cc: stable@vger.kernel.org # 3.12 Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
On success i2c_master_send() returns the number of bytes written. The
call from iio_write_channel_info(), however, expects the return value to
be zero on success.
This bug causes incorrect consumption of the sysfs buffer in
iio_write_channel_info(). When writing more than two characters to
out_voltage0_raw, the ad5446 write handler is called multiple times
causing unexpected behavior.
Fixes: 3ec36a2cf0d5 ("iio:ad5446: Add support for I2C based DACs") Signed-off-by: Pekka Korpinen <pekka.korpinen@iki.fi> Link: https://lore.kernel.org/r/20210929185755.2384-1-pekka.korpinen@iki.fi Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Fix the error path in free_dqentry(), pass out the error number if the
block to free is not correct.
Fixes: 1ccd14b9c271 ("quota: Split off quota tree handling into a separate file") Link: https://lore.kernel.org/r/20211008093821.1001186-3-yi.zhang@huawei.com Signed-off-by: Zhang Yi <yi.zhang@huawei.com> Cc: stable@kernel.org Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The block number in the quota tree on disk should be smaller than the
v2_disk_dqinfo.dqi_blocks. If the quota file was corrupted, we may be
allocating an 'allocated' block and that would lead to a loop in a tree,
which will probably trigger oops later. This patch adds a check for the
block number in the quota tree to prevent such potential issue.
Link: https://lore.kernel.org/r/20211008093821.1001186-2-yi.zhang@huawei.com Signed-off-by: Zhang Yi <yi.zhang@huawei.com> Cc: stable@kernel.org Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The PCIE_MSI_PAYLOAD_REG contains 16-bit MSI number, not only lower
8 bits. Fix reading content of this register and add a comment
describing the access to this register.
MSI domain callback .alloc() (implemented by advk_msi_irq_domain_alloc()
function) should return zero on success, since non-zero value indicates
failure.
When the driver was converted to generic MSI API in commit f21a8b1b6837
("PCI: aardvark: Move to MSI handling using generic MSI support"), it
was converted so that it returns hwirq number.
Fix this.
Link: https://lore.kernel.org/r/20211028185659.20329-3-kabel@kernel.org Fixes: f21a8b1b6837 ("PCI: aardvark: Move to MSI handling using generic MSI support") Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Add support for reporting PCI_EXP_LNKSTA_DLLLA bit in Link Control register
on emulated bridge via current LTSSM state. Also correctly indicate DLLLA
capability via PCI_EXP_LNKCAP_DLLLARC bit in Link Control Capability
register.
There are lot of undocumented interrupt bits. To prevent unwanted
spurious interrupts, fix all *_ALL_MASK macros to define all interrupt
bits, so that driver can properly mask all interrupts, including those
which are undocumented.
The PCIE_ISR1_REG says which interrupts are currently set / active,
including those which are masked.
The driver currently reads this register and looks if some unmasked
interrupts are active, and if not, it clears status bits of _all_
interrupts, including the masked ones.
This is incorrect, since, for example, some drivers may poll these bits.
Remove this clearing, and also remove this early return statement
completely, since it does not change functionality in any way.
The pci_bridge_emul_conf_write() function correctly clears W1C bits in
cfgspace cache, but it does not inform the underlying implementation
about the clear request: the .write_op() method is given the value with
these bits cleared.
This is wrong if the .write_op() needs to know which bits were requested
to be cleared.
Fix the value to be passed into the .write_op() method to have requested
W1C bits set, so that it can clear them.
Both pci-bridge-emul users (mvebu and aardvark) are compatible with this
change.
Link: https://lore.kernel.org/r/20211028185659.20329-2-kabel@kernel.org Fixes: 23a5fba4d941 ("PCI: Introduce PCI bridge emulated config space common logic") Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: stable@vger.kernel.org Cc: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
When running as PVH or HVM guest with actual memory < max memory the
hypervisor is using "populate on demand" in order to allow the guest
to balloon down from its maximum memory size. For this to work
correctly the guest must not touch more memory pages than its target
memory size as otherwise the PoD cache will be exhausted and the guest
is crashed as a result of that.
In extreme cases ballooning down might not be finished today before
the init process is started, which can consume lots of memory.
In order to avoid random boot crashes in such cases, add a late init
call to wait for ballooning down having finished for PVH/HVM guests.
Warn on console if initial ballooning fails, panic() after stalling
for more than 3 minutes per default. Add a module parameter for
changing this timeout.
[boris: replaced pr_info() with pr_notice()]
Cc: <stable@vger.kernel.org> Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Signed-off-by: Juergen Gross <jgross@suse.com> Link: https://lore.kernel.org/r/20211102091944.17487-1-jgross@suse.com Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
In commit 411cef6adfb3 ("ALSA: mixer: oss: Fix racy access to slots")
added mutex protection in snd_mixer_oss_set_volume(). Second
mutex_lock() in same function looks like typo, fix it.
The OSS mixer can reassign the mapping slots dynamically via proc
file. Although the addition and deletion of those slots are protected
by mixer->reg_mutex, the access to slots aren't, hence this may cause
UAF when the slots in use are deleted concurrently.
This patch applies the mixer->reg_mutex in all appropriate code paths
(i.e. the ioctl functions) that may access slots.
Since commit edc6afc54968 ("tty: switch to ktermios and new framework")
termios speed is no longer stored only in c_cflag member but also in new
additional c_ispeed and c_ospeed members. If BOTHER flag is set in c_cflag
then termios speed is stored only in these new members.
Therefore to correctly restore termios speed it is required to store also
ispeed and ospeed members, not only cflag member.
In case only cflag member with BOTHER flag is restored then functions
tty_termios_baud_rate() and tty_termios_input_baud_rate() returns baudrate
stored in c_ospeed / c_ispeed member, which is zero as it was not restored
too. If reported baudrate is invalid (e.g. zero) then serial core functions
report fallback baudrate value 9600. So it means that in this case original
baudrate is lost and kernel changes it to value 9600.
Simple reproducer of this issue is to boot kernel with following command
line argument: "console=ttyXXX,86400" (where ttyXXX is the device name).
For speed 86400 there is no Bnnn constant and therefore kernel has to
represent this speed via BOTHER c_cflag. Which means that speed is stored
only in c_ospeed and c_ispeed members, not in c_cflag anymore.
If bootloader correctly configures serial device to speed 86400 then kernel
prints boot log to early console at speed speed 86400 without any issue.
But after kernel starts initializing real console device ttyXXX then speed
is changed to fallback value 9600 because information about speed was lost.
This patch fixes above issue by storing and restoring also ispeed and
ospeed members, which are required for BOTHER flag.
Fixes: edc6afc54968 ("[PATCH] tty: switch to ktermios and new framework") Cc: stable@vger.kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Link: https://lore.kernel.org/r/20211002130900.9518-1-pali@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
When the field described in mpc85xx_smp_guts_ids[] is not configured in
dtb, the mpc85xx_setup_pmc() does not assign a value to the "guts"
variable. As a result, the oops is triggered when
mpc85xx_freeze_time_base() is executed.
Fixes: 56f1ba280719 ("powerpc/mpc85xx: refactor the PM operations") Cc: stable@vger.kernel.org # v4.6+ Signed-off-by: Xiaoming Ni <nixiaoming@huawei.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20210929033646.39630-2-nixiaoming@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
According to SAE-J1939-82 2015 (A.3.6 Row 2), a receiver should never
send TP.CM_CTS to the global address, so we can add a check in
j1939_can_recv() to drop messages with invalid source address.
Fixes: 9d71dd0c7009 ("can: add support of SAE J1939 protocol") Link: https://lore.kernel.org/all/1635431907-15617-3-git-send-email-zhangchangzhong@huawei.com Cc: stable@vger.kernel.org Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com> Acked-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Check the current VMCS controls to determine if an MSR write will be
intercepted due to MSR bitmaps being disabled. In the nested VMX case,
KVM will disable MSR bitmaps in vmcs02 if they're disabled in vmcs12 or
if KVM can't map L1's bitmaps for whatever reason.
Note, the bad behavior is relatively benign in the current code base as
KVM sets all bits in vmcs02's MSR bitmap by default, clears bits if and
only if L0 KVM also disables interception of an MSR, and only uses the
buggy helper for MSR_IA32_SPEC_CTRL. Because KVM explicitly tests WRMSR
before disabling interception of MSR_IA32_SPEC_CTRL, the flawed check
will only result in KVM reading MSR_IA32_SPEC_CTRL from hardware when it
isn't strictly necessary.
Tag the fix for stable in case a future fix wants to use
msr_write_intercepted(), in which case a buggy implementation in older
kernels could prove subtly problematic.
Fixes: d28b387fb74d ("KVM/VMX: Allow direct access to MSR_IA32_SPEC_CTRL") Cc: stable@vger.kernel.org Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20211109013047.2041518-2-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
On Galaxy S3 (i9300/i9305), which has the max17047 fuel gauge and no
current sense resistor (rsns), the RepSOC register does not provide an
accurate state of charge value. The reported value is wrong, and does
not change over time. VFSOC however, which uses the voltage fuel gauge
to determine the state of charge, always shows an accurate value.
For devices without current sense, VFSOC is already used for the
soc-alert (0x0003 is written to MiscCFG register), so with this change
the source of the alert and the PROP_CAPACITY value match.
Fixes: 359ab9f5b154 ("power_supply: Add MAX17042 Fuel Gauge Driver") Cc: <stable@vger.kernel.org> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Suggested-by: Wolfgang Wiedmeyer <wolfgit@wiedmeyer.de> Signed-off-by: Henrik Grimler <henrik@grimler.se> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
max17042_set_soc_threshold gets called with offset set to 1, which means
that minimum threshold value would underflow once SOC got down to 0,
causing invalid alerts from the gauge.
Fixes: e5f3872d2044 ("max17042: Add support for signalling change in SOC") Cc: <stable@vger.kernel.org> Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
When an instruction to save or restore a register from the stack fails
in _save_fp_context or _restore_fp_context return with -EFAULT. This
change was made to r2300_fpu.S[1] but it looks like it got lost with
the introduction of EX2[2]. This is also what the other implementation
of _save_fp_context and _restore_fp_context in r4k_fpu.S does, and
what is needed for the callers to be able to handle the error.
Furthermore calling do_exit(SIGSEGV) from bad_stack is wrong because
it does not terminate the entire process it just terminates a single
thread.
As the changed code was the only caller of arch/mips/kernel/syscall.c:bad_stack
remove the problematic and now unused helper function.
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Maciej Rozycki <macro@orcam.me.uk> Cc: linux-mips@vger.kernel.org
[1] 35938a00ba86 ("MIPS: Fix ISA I FP sigcontext access violation handling")
[2] f92722dc4545 ("MIPS: Correct MIPS I FP sigcontext layout") Cc: stable@vger.kernel.org Fixes: f92722dc4545 ("MIPS: Correct MIPS I FP sigcontext layout") Acked-by: Maciej W. Rozycki <macro@orcam.me.uk> Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Link: https://lkml.kernel.org/r/20211020174406.17889-5-ebiederm@xmission.com Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The existence of sigkill_pending is a little silly as it is
functionally a duplicate of fatal_signal_pending that is used in
exactly one place.
Checking for pending fatal signals and returning early in ptrace_stop
is actively harmful. It casues the ptrace_stop called by
ptrace_signal to return early before setting current->exit_code.
Later when ptrace_signal reads the signal number from
current->exit_code is undefined, making it unpredictable what will
happen.
Instead rely on the fact that schedule will not sleep if there is a
pending signal that can awaken a task.
Removing the explict sigkill_pending test fixes fixes ptrace_signal
when ptrace_stop does not stop because current->exit_code is always
set to to signr.
The module parameters are missing dev_oper_mode 12, BT classic alone,
add it. Moreover, the parameters encode newlines, which ends up being
printed malformed e.g. by modinfo, so fix that too.
However, the module parameter string is duplicated in both USB and SDIO
modules and the dev_oper_mode mode enumeration in those module parameters
is a duplicate of macros used by the driver. Furthermore, the enumeration
is confusing.
So, deduplicate the module parameter string and use __stringify() to
encode the correct mode enumeration values into the module parameter
string. Finally, replace 'Wi-Fi' with 'Wi-Fi alone' and 'BT' with
'BT classic alone' to clarify what those modes really mean.
Fixes: 898b255339310 ("rsi: add module parameter operating mode") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Amitkumar Karwar <amit.karwar@redpinesignals.com> Cc: Angus Ainslie <angus@akkea.ca> Cc: David S. Miller <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Kalle Valo <kvalo@codeaurora.org> Cc: Karun Eagalapati <karun256@gmail.com> Cc: Martin Fuzzey <martin.fuzzey@flowbird.group> Cc: Martin Kepplinger <martink@posteo.de> Cc: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Cc: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm> Cc: Siva Rebbagondla <siva8118@gmail.com> Cc: netdev@vger.kernel.org Cc: <stable@vger.kernel.org> # 4.17+ Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210916144245.10181-1-marex@denx.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
P2P client mode was only working the first time.
On subsequent connection attempts the group was successfully created but
no data was sent (no transmitted data packets were seen with a sniffer).
The reason for this was that the hardware was being configured in fixed
rate mode with rate RSI_RATE_1 (1Mbps) which is not valid in the 5GHz band.
In P2P mode wpa_supplicant uses NL80211_CMD_SET_TX_BITRATE_MASK to disallow
the 11b rates in the 2.4GHz band which updated common->fixedrate_mask.
rsi_set_min_rate() then used the fixedrate_mask to calculate the minimum
allowed rate, or 0xffff = auto if none was found.
However that calculation did not account for the different rate sets
allowed in the different bands leading to the error.
Fixing set_min_rate() would result in 6Mb/s being used all the time
which is not what we want either.
The reason the problem did not occur on the first connection is that
rsi_mac80211_set_rate_mask() only updated the fixedrate_mask for
the *current* band. When it was called that was still 2.4GHz as the
switch is done later. So the when set_min_rate() was subsequently
called after the switch to 5GHz it still had a mask of zero, leading
to defaulting to auto mode.
Fix this by differentiating the case of a single rate being
requested, in which case the hardware will be used in fixed rate
mode with just that rate, and multiple rates being requested,
in which case we remain in auto mode but the firmware rate selection
algorithm is configured with a restricted set of rates.
Fixes: dad0d04fa7ba ("rsi: Add RS9113 wireless driver") Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group> CC: stable@vger.kernel.org Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1630337206-12410-4-git-send-email-martin.fuzzey@flowbird.group Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
My previous patch checked if encryption should be enabled by directly
checking info->control.hw_key (like the downstream driver).
However that missed that the control and driver_info members of
struct ieee80211_tx_info are union fields.
Due to this when rsi_core_xmit() updates fields in "tx_params"
(driver_info) it can overwrite the control.hw_key, causing the result
of the later test to be incorrect.
With the current structure layout the first byte of control.hw_key is
overlayed with the vap_id so, since we only test if control.hw_key is
NULL / non NULL, a non zero vap_id will incorrectly enable encryption.
In basic STA and AP modes the vap_id is always zero so it works but in
P2P client mode a second VIF is created causing vap_id to be non zero
and hence encryption to be enabled before keys have been set.
Fix this by extracting the key presence flag to a new field in the driver
private tx_params structure and populating it first.
Fixes: 314538041b56 ("rsi: fix AP mode with WPA failure due to encrypted EAPOL") Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group> CC: stable@vger.kernel.org Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1630337206-12410-3-git-send-email-martin.fuzzey@flowbird.group Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
When BT coexistence is enabled (eg oper mode 13, which is the default)
the initialisation on startup sometimes silently fails.
In a normal initialisation we see
usb 1-1.3: Product: Wireless USB Network Module
usb 1-1.3: Manufacturer: Redpine Signals, Inc.
usb 1-1.3: SerialNumber: 000000000001
rsi_91x: rsi_probe: Initialized os intf ops
rsi_91x: rsi_load_9116_firmware: Loading chunk 0
rsi_91x: rsi_load_9116_firmware: Loading chunk 1
rsi_91x: rsi_load_9116_firmware: Loading chunk 2
rsi_91x: Max Stations Allowed = 1
But sometimes the last log is missing and the wlan net device is
not created.
Running a userspace loop that resets the hardware via a GPIO shows the
problem occurring ~5/100 resets.
The problem does not occur in oper mode 1 (wifi only).
Adding logs shows that the initialisation state machine requests a MAC
reset via rsi_send_reset_mac() but the firmware does not reply, leading
to the initialisation sequence being incomplete.
Fix this by delaying attaching the BT adapter until the wifi
initialisation has completed.
With this applied I have done > 300 reset loops with no errors.
Fixes: 716b840c7641 ("rsi: handle BT traffic in driver") Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group> CC: stable@vger.kernel.org Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1630337206-12410-2-git-send-email-martin.fuzzey@flowbird.group Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Firmware sends delete_sta_context_ind when it detects the AP has gone
away in STA mode. Right now the handler for that indication only handles
AP mode; fix it to also handle STA mode.
Cc: stable@vger.kernel.org Signed-off-by: Benjamin Li <benl@squareup.com> Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Reviewed-by: Loic Poulain <loic.poulain@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210901180606.11686-1-benl@squareup.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Checking if DMA is enabled should be done via the
ata_dma_enabled helper function, since the init state
0xff indicates disabled.
This meant that ATA_CMD_READ_LOG_DMA_EXT was used and probed
for before DMA was enabled, which caused hangs for some combinations
of controllers and devices.
It might also have caused it to be incorrectly disabled as broken,
but there have been no reports of that.
Cc: stable@vger.kernel.org BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=195895 Signed-off-by: Reimar Döffinger <Reimar.Doeffinger@gmx.de> Tested-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
On the 88W8897 PCIe+USB card the firmware randomly crashes after setting
the TX ring write pointer. The issue is present in the latest firmware
version 15.68.19.p21 of the PCIe+USB card.
Those firmware crashes can be worked around by reading any PCI register
of the card after setting that register, so read the PCI_VENDOR_ID
register here. The reason this works is probably because we keep the bus
from entering an ASPM state for a bit longer, because that's what causes
the cards firmware to crash.
This fixes a bug where during RX/TX traffic and with ASPM L1 substates
enabled (the specific substates where the issue happens appear to be
platform dependent), the firmware crashes and eventually a command
timeout appears in the logs.
The evm_fixmode is only configurable by command-line option and it is never
modified outside initcalls, so declaring it with __ro_after_init is better.
Add the missing endpoint max-packet sanity check to probe() to avoid
division by zero in ath10k_usb_hif_tx_sg() in case a malicious device
has broken descriptors (or when doing descriptor fuzz testing).
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4fb0 ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes: 4db66499df91 ("ath10k: add initial USB support") Cc: stable@vger.kernel.org # 4.14 Cc: Erik Stromdahl <erik.stromdahl@gmail.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211027080819.6675-2-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.
Fixes: 241b128b6b69 ("ath6kl: add back beginnings of USB support") Cc: stable@vger.kernel.org # 3.4 Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211025120522.6045-3-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Add the missing endpoint max-packet sanity check to probe() to avoid
division by zero in ath10k_usb_hif_tx_sg() in case a malicious device
has broken descriptors (or when doing descriptor fuzz testing).
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4fb0 ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes: 9cbee358687e ("ath6kl: add full USB support") Cc: stable@vger.kernel.org # 3.5 Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211027080819.6675-3-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Add the missing endpoint sanity checks to probe() to avoid division by
zero in mwifiex_write_data_sync() in case a malicious device has broken
descriptors (or when doing descriptor fuzz testing).
Only add checks for the firmware-download boot stage, which require both
command endpoints, for now. The driver looks like it will handle a
missing endpoint during normal operation without oopsing, albeit not
very gracefully as it will try to submit URBs to the default pipe and
fail.
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4fb0 ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes: 4daffe354366 ("mwifiex: add support for Marvell USB8797 chipset") Cc: stable@vger.kernel.org # 3.5 Cc: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211027080819.6675-4-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The computation of TOHM is off by one bit. This missed bit results in
too low a value for TOHM, which can cause errors in regular memory to
incorrectly report:
EDAC MC0: 1 CE Error at MMIOH area, on addr 0x000000207fffa680 on any memory
Fixes: 50d1bb93672f ("sb_edac: add support for Haswell based systems") Cc: stable@vger.kernel.org Reported-by: Meeta Saggi <msaggi@purestorage.com> Signed-off-by: Eric Badger <ebadger@purestorage.com> Signed-off-by: Tony Luck <tony.luck@intel.com> Link: https://lore.kernel.org/r/20211010170127.848113-1-ebadger@purestorage.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The driver was always parsing "s5m8767,pmic-buck-default-dvs-idx", not
"s5m8767,pmic-buck234-default-dvs-idx".
Cc: <stable@vger.kernel.org> Fixes: 26aec009f6b6 ("regulator: add device tree support for s5m8767") Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Acked-by: Rob Herring <robh@kernel.org>
Message-Id: <20211008113723.134648-3-krzysztof.kozlowski@canonical.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The driver and its bindings, before commit 04f9f068a619 ("regulator:
s5m8767: Modify parsing method of the voltage table of buck2/3/4") were
requiring to provide at least one safe/default voltage for DVS registers
if DVS GPIO is not being enabled.
IOW, if s5m8767,pmic-buck2-uses-gpio-dvs is missing, the
s5m8767,pmic-buck2-dvs-voltage should still be present and contain one
voltage.
This requirement was coming from driver behavior matching this condition
(none of DVS GPIO is enabled): it was always initializing the DVS
selector pins to 0 and keeping the DVS enable setting at reset value
(enabled). Therefore if none of DVS GPIO is enabled in devicetree,
driver was configuring the first DVS voltage for buck[234].
Mentioned commit 04f9f068a619 ("regulator: s5m8767: Modify parsing
method of the voltage table of buck2/3/4") broke it because DVS voltage
won't be parsed from devicetree if DVS GPIO is not enabled. After the
change, driver will configure bucks to use the register reset value as
voltage which might have unpleasant effects.
Fix this by relaxing the bindings constrain: if DVS GPIO is not enabled
in devicetree (therefore DVS voltage is also not parsed), explicitly
disable it.
Cc: <stable@vger.kernel.org> Fixes: 04f9f068a619 ("regulator: s5m8767: Modify parsing method of the voltage table of buck2/3/4") Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Acked-by: Rob Herring <robh@kernel.org>
Message-Id: <20211008113723.134648-2-krzysztof.kozlowski@canonical.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
In open_ctree() in btrfs_check_rw_degradable() [1], we check each block
group individually if at least the minimum number of devices is available
for that profile. If all the devices are available, then we don't have to
check degradable.
[1]
open_ctree()
::
3559 if (!sb_rdonly(sb) && !btrfs_check_rw_degradable(fs_info, NULL)) {
Also before calling btrfs_check_rw_degradable() in open_ctee() at the
line number shown below [2] we call btrfs_read_chunk_tree() and down to
add_missing_dev() to record number of missing devices.
[2]
open_ctree()
::
3454 ret = btrfs_read_chunk_tree(fs_info);
At replay_dir_deletes(), if find_dir_range() returns an error we break out
of the main while loop and then assign a value of 0 (success) to the 'ret'
variable, resulting in completely ignoring that an error happened. Fix
that by jumping to the 'out' label when find_dir_range() returns an error
(negative value).
CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
There's a problem with scrub reporting aborted status but returning
error code 0, on a filesystem with missing and readded device.
Roughly these steps:
- mkfs -d raid1 dev1 dev2
- fill with data
- unmount
- make dev1 disappear
- mount -o degraded
- copy more data
- make dev1 appear again
Running scrub afterwards reports that the command was aborted, but the
system log message says the exit code was 0.
It seems that the cause of the error is decrementing
fs_devices->missing_devices but not clearing device->dev_state. Every
time we umount filesystem, it would call close_ctree, And it would
eventually involve btrfs_close_one_device to close the device, but it
only decrements fs_devices->missing_devices but does not clear the
device BTRFS_DEV_STATE_MISSING bit. Worse, this bug will cause Integer
Overflow, because every time umount, fs_devices->missing_devices will
decrease. If fs_devices->missing_devices value hit 0, it would overflow.
With added debugging:
loop1: detected capacity change from 0 to 20971520
BTRFS: device fsid 56ad51f1-5523-463b-8547-c19486c51ebb devid 1 transid 21 /dev/loop1 scanned by systemd-udevd (2311)
loop2: detected capacity change from 0 to 20971520
BTRFS: device fsid 56ad51f1-5523-463b-8547-c19486c51ebb devid 2 transid 17 /dev/loop2 scanned by systemd-udevd (2313)
BTRFS info (device loop1): flagging fs with big metadata feature
BTRFS info (device loop1): allowing degraded mounts
BTRFS info (device loop1): using free space tree
BTRFS info (device loop1): has skinny extents
BTRFS info (device loop1): before clear_missing.00000000f706684d /dev/loop1 0
BTRFS warning (device loop1): devid 2 uuid 6635ac31-56dd-4852-873b-c60f5e2d53d2 is missing
BTRFS info (device loop1): before clear_missing.0000000000000000 /dev/loop2 1
BTRFS info (device loop1): flagging fs with big metadata feature
BTRFS info (device loop1): allowing degraded mounts
BTRFS info (device loop1): using free space tree
BTRFS info (device loop1): has skinny extents
BTRFS info (device loop1): before clear_missing.00000000f706684d /dev/loop1 0
BTRFS warning (device loop1): devid 2 uuid 6635ac31-56dd-4852-873b-c60f5e2d53d2 is missing
BTRFS info (device loop1): before clear_missing.0000000000000000 /dev/loop2 0
BTRFS info (device loop1): flagging fs with big metadata feature
BTRFS info (device loop1): allowing degraded mounts
BTRFS info (device loop1): using free space tree
BTRFS info (device loop1): has skinny extents
BTRFS info (device loop1): before clear_missing.00000000f706684d /dev/loop1 18446744073709551615
BTRFS warning (device loop1): devid 2 uuid 6635ac31-56dd-4852-873b-c60f5e2d53d2 is missing
BTRFS info (device loop1): before clear_missing.0000000000000000 /dev/loop2 18446744073709551615
loop1: detected capacity change from 0 to 20971520
loop2: detected capacity change from 0 to 20971520
BTRFS: device fsid 15aa1203-98d3-4a66-bcae-ca82f629c2cd devid 1 transid 5 /dev/loop1 scanned by mkfs.btrfs (1863)
BTRFS: device fsid 15aa1203-98d3-4a66-bcae-ca82f629c2cd devid 2 transid 5 /dev/loop2 scanned by mkfs.btrfs (1863)
BTRFS info (device loop1): flagging fs with big metadata feature
BTRFS info (device loop1): allowing degraded mounts
BTRFS info (device loop1): disk space caching is enabled
BTRFS info (device loop1): has skinny extents
BTRFS info (device loop1): before clear_missing.00000000975bd577 /dev/loop1 0
BTRFS warning (device loop1): devid 2 uuid 8b333791-0b3f-4f57-b449-1c1ab6b51f38 is missing
BTRFS info (device loop1): before clear_missing.0000000000000000 /dev/loop2 1
BTRFS info (device loop1): checking UUID tree
BTRFS info (device loop1): flagging fs with big metadata feature
BTRFS info (device loop1): allowing degraded mounts
BTRFS info (device loop1): disk space caching is enabled
BTRFS info (device loop1): has skinny extents
BTRFS info (device loop1): before clear_missing.00000000975bd577 /dev/loop1 0
BTRFS warning (device loop1): devid 2 uuid 8b333791-0b3f-4f57-b449-1c1ab6b51f38 is missing
BTRFS info (device loop1): before clear_missing.0000000000000000 /dev/loop2 1
BTRFS info (device loop1): flagging fs with big metadata feature
BTRFS info (device loop1): allowing degraded mounts
BTRFS info (device loop1): disk space caching is enabled
BTRFS info (device loop1): has skinny extents
BTRFS info (device loop1): before clear_missing.00000000975bd577 /dev/loop1 0
BTRFS warning (device loop1): devid 2 uuid 8b333791-0b3f-4f57-b449-1c1ab6b51f38 is missing
BTRFS info (device loop1): before clear_missing.0000000000000000 /dev/loop2 1
CC: stable@vger.kernel.org # 4.19+ Signed-off-by: Li Zhang <zhanglikernel@gmail.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
There should use TCPF_SYN_RECV instead of TCP_SYN_RECV.
Signed-off-by: Wen Gu <guwen@linux.alibaba.com> Reviewed-by: Tony Lu <tonylu@linux.alibaba.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
MTU change is refused whenever the value of new MTU is bigger than
the max packet bytes that fits in NFP Cluster Target Memory (CTM).
However, an eBPF program doesn't always need to access the whole
packet data.
The maximum direct packet access (DPA) offset has always been
caculated by verifier and stored in the max_pkt_offset field of prog
aux data.
Signed-off-by: Yu Xiao <yu.xiao@corigine.com> Reviewed-by: Yinjun Zhang <yinjun.zhang@corigine.com> Reviewed-by: Niklas Soderlund <niklas.soderlund@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Pass the correct length to nvmet_tcp_verify_hdgst, which is the pdu
header length. This fixes a wrong behaviour where header digest
verification passes although the digest is wrong.
Signed-off-by: Amit Engel <amit.engel@dell.com> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>