When the error check in ath9k_hw_read_revisions() was added, it checked for
-EIO which is what ath9k_regread() in the ath9k_htc driver uses. However,
for plain ath9k, the register read function uses ioread32(), which just
returns -1 on error. So if such a read fails, it still gets passed through
and ends up as a weird mac revision in the log output.
Fix this by changing ath9k_regread() to return -1 on error like ioread32()
does, and fix the error check to look for that instead of -EIO.
Fixes: 2f90c7e5d094 ("ath9k: Check for errors when reading SREV register") Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210326180819.142480-1-toke@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The Intel xway phys offer the possibility to deactivate the integrated
LED function and to control the LEDs manually.
If this was set by the bootloader, it must be ensured that the
integrated LED function is enabled for all LEDs when loading the driver.
Before commit 6e2d85ec0559 ("net: phy: Stop with excessive soft reset")
the LEDs were enabled by a soft-reset of the PHY (using
genphy_soft_reset). Initialize the XWAY_MDIO_LED with it's default
value (which is applied during a soft reset) instead of adding back
the soft reset. This brings back the default LED configuration while
still preventing an excessive amount of soft resets.
Fixes: 6e2d85ec0559 ("net: phy: Stop with excessive soft reset") Signed-off-by: Martin Schiller <ms@dev.tdt.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When a lot of frames were received in the short term, the driver
caused a stuck of receiving until a new frame was received. For example,
the following command from other device could cause this issue.
The previous code always cleared the interrupt flag of RX but checks
the interrupt flags in ravb_poll(). So, ravb_poll() could not call
ravb_rx() in the next time until a new RX frame was received if
ravb_rx() returned true. To fix the issue, always calls ravb_rx()
regardless the interrupt flags condition.
Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper") Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The bit-masks used for the TXERRCH and RXERRCH (tx and rx error channels)
are incorrect and always lead to a zero result. The mask values are
currently the incorrect post-right shifted values, fix this by setting
them to the currect values.
(I double checked these against the TMS320TCI6482 data sheet, section
5.30, page 127 to ensure I had the correct mask values for the TXERRCH
and RXERRCH fields in the MACSTATUS register).
Addresses-Coverity: ("Operands don't affect result") Fixes: a6286ee630f6 ("net: Add TI DaVinci EMAC driver") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Currently when the call to usb_urb_ep_type_check fails (returning -EINVAL)
the error return path returns -ENOMEM via the exit label "error". Other
uses of the same error exit label set the err variable to -ENOMEM but this
is not being used. I believe the original intent was for the error exit
path to return the value in err rather than the hard coded -ENOMEM, so
return this rather than the hard coded -ENOMEM.
Addresses-Coverity: ("Unused value") Fixes: 738d9edcfd44 ("ALSA: usb-audio: Add sanity checks for invalid EPs") Signed-off-by: Colin Ian King <colin.king@canonical.com> Link: https://lore.kernel.org/r/20210420134719.381409-1-colin.king@canonical.com Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
missing qpid increment leads to skipping few qpids while allocating QP.
This eventually leads to adapter running out of qpids after establishing
fewer connections than it actually supports.
Current patch increments the qpid correctly.
Fixes: cfdda9d76436 ("RDMA/cxgb4: Add driver for Chelsio T4 RNIC") Link: https://lore.kernel.org/r/20210415151422.9139-1-bharat@chelsio.com Signed-off-by: Potnuri Bharat Teja <bharat@chelsio.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Commit 38ec4944b593 ("gro: ensure frag0 meets IP header alignment")
did the right thing, but missed the fact that napi_gro_frags() logics
calls for skb_gro_reset_offset() *before* pulling Ethernet header
to the skb linear space.
That said, the introduced check for frag0 address being aligned to 4
always fails for it as Ethernet header is obviously 14 bytes long,
and in case with NET_IP_ALIGN its start is not aligned to 4.
Fix this by adding @nhoff argument to skb_gro_reset_offset() which
tells if an IP header is placed right at the start of frag0 or not.
This restores Fast GRO for napi_gro_frags() that became very slow
after the mentioned commit, and preserves the introduced check to
avoid silent unaligned accesses.
From v1 [0]:
- inline tiny skb_gro_reset_offset() to let the code be optimized
more efficively (esp. for the !NET_IP_ALIGN case) (Eric);
- pull in Reviewed-by from Eric.
Fixes: 38ec4944b593 ("gro: ensure frag0 meets IP header alignment") Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Alexander Lobakin <alobakin@pm.me> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
VMCI feature is not supported in conjunction with the vSphere Fault
Tolerance (FT) feature.
VMware Tools can repeatedly try to create a vsock connection. If FT is
enabled the kernel logs is flooded with the following messages:
qp_alloc_hypercall result = -20
Could not attach to queue pair with -20
"qp_alloc_hypercall result = -20" was hidden by commit e8266c4c3307
("VMCI: Stop log spew when qp allocation isn't possible"), but "Could
not attach to queue pair with -20" is still there flooding the log.
Since the error message can be useful in some cases, print it only once.
Fixes: d021c344051a ("VSOCK: Introduce VM Sockets") Signed-off-by: Stefano Garzarella <sgarzare@redhat.com> Reviewed-by: Jorgen Hansen <jhansen@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In mwl8k_probe_hw, hw->priv->txq is freed at the first time by
dma_free_coherent() in the call chain:
if(!priv->ap_fw)->mwl8k_init_txqs(hw)->mwl8k_txq_init(hw, i).
Then in err_free_queues of mwl8k_probe_hw, hw->priv->txq is freed
at the second time by mwl8k_txq_deinit(hw, i)->dma_free_coherent().
My patch set txq->txd to NULL after the first free to avoid the
double free.
Fixes: a66098daacee2 ("mwl8k: Marvell TOPDOG wireless driver") Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210402182627.4256-1-lyl2019@mail.ustc.edu.cn Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
While adding the invalid IRQ check after calling platform_get_irq(),
I managed to overlook that the driver has a complex error path in its
probe() method, thus a simple *return* couldn't be used. Use a proper
*goto* instead!
Fixes: e5b2e3e74201 ("i2c: sh7760: add IRQ check") Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The signal strength of 5G is quite low, so user can't connect to an AP far
away. New parameters with new format and its parser are updated by the commit 84d26fda52e2 ("rtlwifi: Update 8821ae new phy parameters and its parser."), but
some parameters are missing. Use this commit to update to the novel parameters
that use new format.
Fixes: 84d26fda52e2 ("rtlwifi: Update 8821ae new phy parameters and its parser") Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210219052607.7323-1-pkshih@realtek.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The pci_bus->bridge reference may no longer be valid after
pci_bus_remove() resulting in passing a bad value to device_unregister()
for the associated bridge device.
Store the host_bridge reference in a separate variable prior to
pci_bus_remove().
Fixes: 7340056567e3 ("powerpc/pci: Reorder pci bus/bridge unregistration during PHB removal") Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20210211182435.47968-1-tyreld@linux.ibm.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Mirror commit aeba3731b150 ("powerpc/pci: Fix IO space breakage after
of_pci_range_to_resource() change").
Most MIPS platforms do not define PCI_IOBASE, nor implement
pci_address_to_pio(). Moreover, IO_SPACE_LIMIT is 0xffff for most MIPS
platforms. of_pci_range_to_resource passes the _start address_ of the IO
range into pci_address_to_pio, which then checks it against
IO_SPACE_LIMIT and fails, because for MIPS platforms that use
pci-legacy (pci-lantiq, pci-rt3883, pci-mt7620), IO ranges start much
higher than 0xffff.
In fact, pci-mt7621 in staging already works around this problem, see
commit 09dd629eeabb ("staging: mt7621-pci: fix io space and properly set
resource limits")
So just stop using of_pci_range_to_resource, which does not work for
MIPS.
After gnulib update sed stopped matching `[[:space:]]*+' as before,
causing the following compilation error:
In file included from builtin-trace.c:719:
trace/beauty/generated/fsconfig_arrays.c:2:3: error: expected expression before ']' token
2 | [] = "",
| ^
trace/beauty/generated/fsconfig_arrays.c:2:3: error: array index in initializer not of integer type
trace/beauty/generated/fsconfig_arrays.c:2:3: note: (near initialization for 'fsconfig_cmds')
Fix this by correcting the regular expression used in the generator.
Also, clean up the script by removing redundant egrep, xargs, and printf
invocations.
The intel_gvt_init_vgpu_type_groups() function is only called from
intel_gvt_init_device(). If it fails then the intel_gvt_init_device()
prints the error code and propagates it back again. That's a bug
because false is zero/success. The fix is to modify it to return zero
or negative error codes and make everything consistent.
Fixes: c5d71cb31723 ("drm/i915/gvt: Move vGPU type related code into gvt file") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/YHaFQtk/DIVYK1u5@mwanda Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Reset (aka power off) happens when the reset gpio is made active.
The reset gpio is GPIO_ACTIVE_LOW
Fixes: 920884777480 ("ASoC: ak5558: Add support for AK5558 ADC driver") Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com> Link: https://lore.kernel.org/r/1618382024-31725-1-git-send-email-shengjiu.wang@nxp.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When under xmon, the "dxi" command dumps the state of the XIVE
interrupts. If an interrupt number is specified, only the state of
the associated XIVE interrupt is dumped. This form of the command
lacks an irq_data parameter which is nevertheless used by
xmon_xive_get_irq_config(), leading to an xmon crash.
Fix that by doing a lookup in the system IRQ mapping to query the IRQ
descriptor data. Invalid interrupt numbers, or not belonging to the
XIVE IRQ domain, OPAL event interrupt number for instance, should be
caught by the previous query done at the firmware level.
Fixes: 97ef27507793 ("powerpc/xive: Fix xmon support on the PowerNV platform") Reported-by: kernel test robot <lkp@intel.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Cédric Le Goater <clg@kaod.org> Tested-by: Greg Kurz <groug@kaod.org> Reviewed-by: Greg Kurz <groug@kaod.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20210331144514.892250-8-clg@kaod.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_irq() (which
takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding
an original error code. Stop calling devm_request_irq() with invalid
IRQ #s.
Fixes: a26c20b1fa6d ("i2c: Renesas SH7760 I2C master driver") Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_irq() (which
takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding
an original error code. Stop calling devm_request_irq() with invalid
IRQ #s.
Fixes: ba92222ed63a ("i2c: jz4780: Add i2c bus controller driver for Ingenic JZ4780") Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_irq() (which
takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding
an original error code. Stop calling devm_request_irq() with invalid
IRQ #s.
Fixes: 5faf6e1f58b4 ("i2c: emev2: add driver") Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_irq() (which
takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding
an original error code. Stop calling devm_request_irq() with invalid
IRQ #s.
Fixes: df8eb5691c48 ("i2c: Add driver for Cadence I2C controller") Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The PM reference count is not expected to be incremented on
return in omap_i2c_probe() and omap_i2c_remove().
However, pm_runtime_get_sync will increment the PM reference
count even failed. Forgetting to putting operation will result
in a reference leak here. I Replace it with pm_runtime_resume_and_get
to keep usage counter balanced.
What's more, error path 'err_free_mem' seems not like a proper
name any more. So I change the name to err_disable_pm and move
pm_runtime_disable below, for pm_runtime of 'pdev->dev' should
be disabled when pm_runtime_resume_and_get fails.
Fixes: 3b0fb97c8dc4 ("I2C: OMAP: Handle error check for pm runtime") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com> Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The shifting of the u8 integers rq->caching by 26 bits to
the left will be promoted to a 32 bit signed int and then
sign-extended to a u64. In the event that rq->caching is
greater than 0x1f then all then all the upper 32 bits of
the u64 end up as also being set because of the int
sign-extension. Fix this by casting the u8 values to a
u64 before the 26 bit left shift.
Addresses-Coverity: ("Unintended sign extension") Fixes: 4863dea3fab0 ("net: Adding support for Cavium ThunderX network controller") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The shifting of the u8 integers f->fs.nat_lip[] by 24 bits to
the left will be promoted to a 32 bit signed int and then
sign-extended to a u64. In the event that the top bit of the u8
is set then all then all the upper 32 bits of the u64 end up as
also being set because of the sign-extension. Fix this by
casting the u8 values to a u64 before the 24 bit left shift.
Addresses-Coverity: ("Unintended sign extension") Fixes: 12b276fbf6e0 ("cxgb4: add support to create hash filters") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The host CTRL (runlatch) value is not restored after guest exit. The
host CTRL should always be 1 except in CPU idle code, so this can result
in the host running with runlatch clear, and potentially switching to
a different vCPU which then runs with runlatch clear as well.
This has little effect on P9 machines, CTRL is only responsible for some
PMU counter logic in the host and so other than corner cases of software
relying on that, or explicitly reading the runlatch value (Linux does
not appear to be affected but it's possible non-Linux guests could be),
there should be no execution correctness problem, though it could be
used as a covert channel between guests.
There may be microcontrollers, firmware or monitoring tools that sample
the runlatch value out-of-band, however since the register is writable
by guests, these values would (should) not be relied upon for correct
operation of the host, so suboptimal performance or incorrect reporting
should be the worst problem.
Fixes: 95a6432ce9038 ("KVM: PPC: Book3S HV: Streamlined guest entry/exit path on P9 for radix guests") Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20210412014845.1517916-2-npiggin@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Currently the expression ~nic_conf1 is always true because nic_conf1
is a u16 and according to 6.5.3.3 of the C standard the ~ operator
promotes the u16 to an integer before flipping all the bits. Thus
the top 16 bits of the integer result are all set so the expression
is always true. If the intention was to flip all the bits of nic_conf1
then casting the integer result back to a u16 is a suitabel fix.
Interestingly static analyzers seem to thing a bitwise ! should be
used instead of ~ for this scenario, so I think the original intent
of the expression may need some extra consideration.
Addresses-Coverity: ("Logical vs. bitwise operator") Fixes: c869f77d6abb ("add mt7601u driver") Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Jakub Kicinski <kubakici@wp.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210225183241.1002129-1-colin.king@canonical.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
If any of the cipher schemes specified by the driver are invalid, bail
out and fail the registration rather than just warning. Otherwise, we
might later crash when we try to use the invalid cipher scheme, e.g.
if the hdr_len is (significantly) less than the pn_offs + pn_len, we'd
have an out-of-bounds access in RX validation.
When neither CONFIG_PCI nor CONFIG_IBMVIO is set/enabled, iommu.c has a
build error. The fault injection code is not useful in that kernel config,
so make the FAIL_IOMMU option depend on PCI || IBMVIO.
Prevents this build error (warning escalated to error):
../arch/powerpc/kernel/iommu.c:178:30: error: 'fail_iommu_bus_notifier' defined but not used [-Werror=unused-variable]
178 | static struct notifier_block fail_iommu_bus_notifier = {
Fixes: d6b9a81b2a45 ("powerpc: IOMMU fault injection") Reported-by: kernel test robot <lkp@intel.com> Suggested-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20210404192623.10697-1-rdunlap@infradead.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The power PMU group constraints includes check for EBB events to make
sure all events in a group must agree on EBB. This will prevent
scheduling EBB and non-EBB events together. But in the existing check,
settings for constraint mask and value is interchanged. Patch fixes the
same.
Before the patch, PMU selftest "cpu_event_pinned_vs_ebb_test" fails with
below in dmesg logs. This happens because EBB event gets enabled along
with a non-EBB cpu event.
[35600.453346] cpu_event_pinne[41326]: illegal instruction (4)
at 10004a18 nip 10004a18 lr 100049f8 code 1 in
cpu_event_pinned_vs_ebb_test[10000000+10000]
Test results after the patch:
$ ./pmu/ebb/cpu_event_pinned_vs_ebb_test
test: cpu_event_pinned_vs_ebb
tags: git_version:v5.12-rc5-93-gf28c3125acd3-dirty
Binding to cpu 8
EBB Handler is at 0x100050c8
read error on event 0x7fffe6bd4040!
PM_RUN_INST_CMPL: result 9872 running/enabled 37930432
success: cpu_event_pinned_vs_ebb
This bug was hidden by other logic until commit 1908dc911792 (perf:
Tweak perf_event_attr::exclusive semantics).
Fixes: 4df489991182 ("powerpc/perf: Add power8 EBB support") Reported-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
[mpe: Mention commit 1908dc911792] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/1617725761-1464-1-git-send-email-atrajeev@linux.vnet.ibm.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When adding a PTE a ptesync is needed to order the update of the PTE
with subsequent accesses otherwise a spurious fault may be raised.
radix__set_pte_at() does not do this for performance gains. For
non-kernel memory this is not an issue as any faults of this kind are
corrected by the page fault handler. For kernel memory these faults
are not handled. The current solution is that there is a ptesync in
flush_cache_vmap() which should be called when mapping from the
vmalloc region.
However, map_kernel_page() does not call flush_cache_vmap(). This is
troublesome in particular for code patching with Strict RWX on radix.
In do_patch_instruction() the page frame that contains the instruction
to be patched is mapped and then immediately patched. With no ordering
or synchronization between setting up the PTE and writing to the page
it is possible for faults.
As the code patching is done using __put_user_asm_goto() the resulting
fault is obscured - but using a normal store instead it can be seen:
This results in the kind of issue reported here:
https://lore.kernel.org/linuxppc-dev/15AC5B0E-A221-4B8C-9039-FA96B8EF7C88@lca.pw/
Chris Riedl suggested a reliable way to reproduce the issue:
$ mount -t debugfs none /sys/kernel/debug
$ (while true; do echo function > /sys/kernel/debug/tracing/current_tracer ; echo nop > /sys/kernel/debug/tracing/current_tracer ; done) &
Turning ftrace on and off does a large amount of code patching which
in usually less then 5min will crash giving a trace like:
The macro CN23XX_PEM_BAR1_INDEX_REG is being used to shift oct->pcie_port
(a u16) left 24 places. There are two subtle issues here, first the
shift gets promoted to an signed int and then sign extended to a u64.
If oct->pcie_port is 0x80 or more then the upper bits get sign extended
to 1. Secondly shfiting a u16 24 bits will lead to an overflow so it
needs to be cast to a u64 for all the bits to not overflow.
It is entirely possible that the u16 port value is never large enough
for this to fail, but it is useful to fix unintended overflows such
as this.
Fix this by casting the port parameter to the macro to a u64 before
the shift.
Addresses-Coverity: ("Unintended sign extension") Fixes: 5bc67f587ba7 ("liquidio: CN23XX register definitions") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The 'single_cpu' local variable is assigned by asoc_simple_parse_dai()
and later used in a asoc_simple_canonicalize_cpu() call, assuming the
entire function did not exit on errors.
However the first function returns 0 if passed device_node is NULL,
thus leaving the variable uninitialized and reporting success.
Addresses-Coverity: Uninitialized scalar variable Fixes: 8f7f298a3337 ("ASoC: simple-card-utils: separate asoc_simple_card_parse_dai()") Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Acked-by: Sameer Pujar <spujar@nvidia.com> Link: https://lore.kernel.org/r/20210407092027.60769-1-krzysztof.kozlowski@canonical.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
There are a few calls of usb_driver_claim_interface() but all of those
miss the proper error checks, as reported by Coverity. This patch
adds those missing checks.
Along with it, replace the magic pointer with -1 with a constant
USB_AUDIO_IFACE_UNUSED for better readability.
Fixes: c3b1e1e8a76f ("NFC: Export NFCID1 from pn533") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
report_bug() will return early if it cannot find a bug corresponding to
the provided address. The subsequent test for the bug will always be
true so remove it.
Fixes: 1b4cfe3c0a30d ("lib/bug.c: exclude non-BUG/WARN exceptions from report_bug()") Signed-off-by: Andrew Scull <ascull@google.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: "Steven Rostedt (VMware)" <rostedt@goodmis.org> Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Acked-by: Will Deacon <will@kernel.org> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20210318143311.839894-2-ascull@google.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In commit 73f156a6e8c1 ("inetpeer: get rid of ip_id_count")
I used a very small hash table that could be abused
by patient attackers to reveal sensitive information.
Switch to a dynamic sizing, depending on RAM size.
Typical big hosts will now use 128x more storage (2 MB)
to get a similar increase in security and reduction
of hash collisions.
As a bonus, use of alloc_large_system_hash() spreads
allocated memory among all NUMA nodes.
Fixes: 73f156a6e8c1 ("inetpeer: get rid of ip_id_count") Reported-by: Amit Klein <aksecurity@gmail.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Willy Tarreau <w@1wt.eu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
If identical_pvr_fixup() is not inlined, there are two modpost warnings:
WARNING: modpost: vmlinux.o(.text+0x54e8): Section mismatch in reference
from the function identical_pvr_fixup() to the function
.init.text:of_get_flat_dt_prop()
The function identical_pvr_fixup() references
the function __init of_get_flat_dt_prop().
This is often because identical_pvr_fixup lacks a __init
annotation or the annotation of of_get_flat_dt_prop is wrong.
WARNING: modpost: vmlinux.o(.text+0x551c): Section mismatch in reference
from the function identical_pvr_fixup() to the function
.init.text:identify_cpu()
The function identical_pvr_fixup() references
the function __init identify_cpu().
This is often because identical_pvr_fixup lacks a __init
annotation or the annotation of identify_cpu is wrong.
identical_pvr_fixup() calls two functions marked as __init and is only
called by a function marked as __init so it should be marked as __init
as well. At the same time, remove the inline keywork as it is not
necessary to inline this function. The compiler is still free to do so
if it feels it is worthwhile since commit 889b3c1245de ("compiler:
remove CONFIG_OPTIMIZE_INLINING entirely").
If fadump_calculate_reserve_size() is not inlined, there is a modpost
warning:
WARNING: modpost: vmlinux.o(.text+0x5196c): Section mismatch in
reference from the function fadump_calculate_reserve_size() to the
function .init.text:parse_crashkernel()
The function fadump_calculate_reserve_size() references
the function __init parse_crashkernel().
This is often because fadump_calculate_reserve_size lacks a __init
annotation or the annotation of parse_crashkernel is wrong.
fadump_calculate_reserve_size() calls parse_crashkernel(), which is
marked as __init and fadump_calculate_reserve_size() is called from
within fadump_reserve_mem(), which is also marked as __init.
Mark fadump_calculate_reserve_size() as __init to fix the section
mismatch. Additionally, remove the inline keyword as it is not necessary
to inline this function; the compiler is still free to do so if it feels
it is worthwhile since commit 889b3c1245de ("compiler: remove
CONFIG_OPTIMIZE_INLINING entirely").
Fixes: 11550dc0a00b ("powerpc/fadump: reuse crashkernel parameter for fadump memory reservation") Signed-off-by: Nathan Chancellor <nathan@kernel.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://github.com/ClangBuiltLinux/linux/issues/1300 Link: https://lore.kernel.org/r/20210302195013.2626335-1-nathan@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
There are two "netif_running" checks in this driver. One is in
"lapbeth_xmit" and the other is in "lapbeth_rcv". They serve to make
sure that the LAPB APIs called in these functions are called before
"lapb_unregister" is called by the "ndo_stop" function.
However, these "netif_running" checks are unreliable, because it's
possible that immediately after "netif_running" returns true, "ndo_stop"
is called (which causes "lapb_unregister" to be called).
This patch adds locking to make sure "lapbeth_xmit" and "lapbeth_rcv" can
reliably check and ensure the netif is running while doing their work.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Xie He <xie.he.0141@gmail.com> Acked-by: Martin Schiller <ms@dev.tdt.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The 'ret' variable was initialized to zero but then it was not updated
from the fprintf() return, fix it.
Reported-by: Yang Li <yang.lee@linux.alibaba.com>
cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
cc: Ingo Molnar <mingo@redhat.com>
cc: Jiri Olsa <jolsa@redhat.com>
cc: Mark Rutland <mark.rutland@arm.com>
cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com> Fixes: 90f18e63fbd00513 ("perf symbols: List symbols in a dso in ascending name order") Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Plantronics Blackwire 3220 Series (047f:c056) sends HID reports twice
for each volume key press. This patch adds a quirk to hid-plantronics
for this product ID, which will ignore the second volume key press if
it happens within 5 ms from the last one that was handled.
The patch was tested on the mentioned model only, it shouldn't affect
other models, however, this quirk might be needed for them too.
Auto-repeat (when a key is held pressed) is not affected, because the
rate is about 3 times per second, which is far less frequent than once
in 5 ms.
In null_init, null_add_dev(dev) is called.
In null_add_dev, it calls null_free_zoned_dev(dev) to free dev->zones
via kvfree(dev->zones) in out_cleanup_zone branch and returns err.
Then null_init accept the err code and then calls null_free_dev(dev).
But in null_free_dev(dev), dev->zones is freed again by
null_free_zoned_dev().
My patch set dev->zones to NULL in null_free_zoned_dev() after
kvfree(dev->zones) is called, to avoid the double free.
Fixes: 2984c8684f962 ("nullb: factor disk parameters") Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn> Link: https://lore.kernel.org/r/20210426143229.7374-1-lyl2019@mail.ustc.edu.cn Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The handling of sysrq key can be activated by echoing the key to
/proc/sysrq-trigger or via the magic key sequence typed into a terminal
that is connected to the system in some way (serial, USB or other mean).
In the former case, the handling is done in a user context. In the
latter case, it is likely to be in an interrupt context.
Currently in print_cpu() of kernel/sched/debug.c, sched_debug_lock is
taken with interrupt disabled for the whole duration of the calls to
print_*_stats() and print_rq() which could last for the quite some time
if the information dump happens on the serial console.
If the system has many cpus and the sched_debug_lock is somehow busy
(e.g. parallel sysrq-t), the system may hit a hard lockup panic
depending on the actually serial console implementation of the
system.
The purpose of sched_debug_lock is to serialize the use of the global
cgroup_path[] buffer in print_cpu(). The rests of the printk calls don't
need serialization from sched_debug_lock.
Calling printk() with interrupt disabled can still be problematic if
multiple instances are running. Allocating a stack buffer of PATH_MAX
bytes is not feasible because of the limited size of the kernel stack.
The solution implemented in this patch is to allow only one caller at a
time to use the full size group_path[], while other simultaneous callers
will have to use shorter stack buffers with the possibility of path
name truncation. A "..." suffix will be printed if truncation may have
happened. The cgroup path name is provided for informational purpose
only, so occasional path name truncation should not be a big problem.
Fixes: efe25c2c7b3a ("sched: Reinstate group names in /proc/sched_debug") Suggested-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Waiman Long <longman@redhat.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20210415195426.6677-1-longman@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
dev_attr_show() calls _iommu_event_show() via an indirect call but
_iommu_event_show()'s type does not currently match the type of the
show() member in 'struct device_attribute', resulting in a Control Flow
Integrity violation.
If some of the allocations fail between the dev_set_name() and the
device_register() then the name will not be freed. Fix this by
moving dev_set_name() directly in front of the call to device_register().
Fixes: a2aa24734d9d ("HSI: Add common DT binding for HSI client devices") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The ARR register is cleared unconditionally upon probing, after the maximum
value has been read. This initial condition is rather not intuitive, when
considering the counter child driver. It rather expects the maximum value
by default:
- The counter interface shows a zero value by default for 'ceiling'
attribute.
- Enabling the counter without any prior configuration makes it doesn't
count.
The reset value of ARR register is the maximum. So Choice here
is to backup it, and restore it then, instead of clearing its value.
It also fixes the initial condition seen by the counter driver.
Fixes: d0f949e220fd ("mfd: Add STM32 Timers driver") Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com> Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
This fixes an issue hitting the BUG_ON() in ibmvfc_do_work(). When going
through a host action of IBMVFC_HOST_ACTION_RESET, we change the action to
IBMVFC_HOST_ACTION_TGT_DEL, then drop the host lock, and reset the CRQ,
which changes the host state to IBMVFC_NO_CRQ. If, prior to setting the
host state to IBMVFC_NO_CRQ, ibmvfc_init_host() is called, it can then end
up changing the host action to IBMVFC_HOST_ACTION_INIT. If we then change
the host state to IBMVFC_NO_CRQ, we will then hit the BUG_ON().
Make a couple of changes to avoid this. Leave the host action to be
IBMVFC_HOST_ACTION_RESET or IBMVFC_HOST_ACTION_REENABLE until after we drop
the host lock and reset or reenable the CRQ. Also harden the host state
machine to ensure we cannot leave the reset / reenable state until we've
finished processing the reset or reenable.
Link: https://lore.kernel.org/r/20210413001009.902400-1-tyreld@linux.ibm.com Fixes: 73ee5d867287 ("[SCSI] ibmvfc: Fix soft lockup on resume") Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
[tyreld: added fixes tag] Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
[mkp: fix comment checkpatch warnings] Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to request_irq() (which takes
*unsigned* IRQ #s), causing it to fail with -EINVAL (overridden by -ENODEV
further below). Stop calling request_irq() with the invalid IRQ #s.
Link: https://lore.kernel.org/r/8f4b8fa5-8251-b977-70a1-9099bcb4bb17@omprussia.ru Fixes: c27d85f3f3c5 ("[SCSI] SNI RM 53c710 driver") Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to request_irq() (which takes
*unsigned* IRQ #), causing it to fail with -EINVAL, overriding the real
error code. Stop calling request_irq() with the invalid IRQ #s.
Link: https://lore.kernel.org/r/363eb4c8-a3bf-4dc9-2a9e-90f349030a15@omprussia.ru Fixes: 0bb67f181834 ("[SCSI] sun3x_esp: convert to esp_scsi") Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to request_irq() (which takes
*unsigned* IRQ #), causing it to fail with -EINVAL, overriding the real
error code. Stop calling request_irq() with the invalid IRQ #s.
Link: https://lore.kernel.org/r/594aa9ae-2215-49f6-f73c-33bd38989912@omprussia.ru Fixes: 352e921f0dd4 ("[SCSI] jazz_esp: converted to use esp_core") Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Commit df2d8213d9e3 ("hisi_sas: use platform_get_irq()") failed to take
into account that irq_of_parse_and_map() and platform_get_irq() have a
different way of indicating an error: the former returns 0 and the latter
returns a negative error code. Fix up the IRQ checks!
Link: https://lore.kernel.org/r/810f26d3-908b-1d6b-dc5c-40019726baca@omprussia.ru Fixes: df2d8213d9e3 ("hisi_sas: use platform_get_irq()") Acked-by: John Garry <john.garry@huawei.com> Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The for-loop iterates with a u8 loop counter i and compares this
with the loop upper limit of num_parents that is an int type.
There is a potential infinite loop if num_parents is larger than
the u8 loop counter. Fix this by making the loop counter the same
type as num_parents. Also make num_parents an unsigned int to
match the return type of the call to clk_hw_get_num_parents.
Addresses-Coverity: ("Infinite loop") Fixes: 734d82f4a678 ("clk: uniphier: add core support code for UniPhier clock driver") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Masahiro Yamada <masahiroy@kernel.org> Link: https://lore.kernel.org/r/20210409090104.629722-1-colin.king@canonical.com Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
CONFIG_QCOM_A53PLL is tristate option and therefore this driver can be
compiled as a module. This patch adds missing MODULE_DEVICE_TABLE
definition which generates correct modalias for automatic loading of
this driver when it is built as an external module.
The round_rate callback should only perform rate calculation and not
involve calling zynqmp_pll_set_mode to change the pll mode. So let's
move zynqmp_pll_set_mode out of round_rate and to set_rate callback.
Fixes: 3fde0e16d016 ("drivers: clk: Add ZynqMP clock driver") Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com> Link: https://lore.kernel.org/r/20210406154015.602779-1-quanyang.wang@windriver.com Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When a request is re-inited it will release all control handler
objects that are still in the request. It does that by unbinding
and putting all those objects. When the object is unbound the
obj->req pointer is set to NULL, and the object's unbind op is
called. When the object it put the object's release op is called
to free the memory.
For a request object that contains a control handler that means
that v4l2_ctrl_handler_free() is called in the release op.
A control handler used in a request has a pointer to the main
control handler that is created by the driver and contains the
current state of all controls. If the device is unbound (due to
rmmod or a forced unbind), then that main handler is freed, again
by calling v4l2_ctrl_handler_free(), and any outstanding request
objects that refer to that main handler have to be unbound and put
as well.
It does that by this test:
if (!hdl->req_obj.req && !list_empty(&hdl->requests)) {
I.e. the handler has no pointer to a request, so is the main
handler, and one or more request objects refer to this main
handler.
However, this test is wrong since hdl->req_obj.req is actually
NULL when re-initing a request (the object unbind will set req to
NULL), and the only reason this seemingly worked is that the
requests list is typically empty since the request's unbind op
will remove the handler from the requests list.
But if another thread is at the same time adding a new control
to a request, then there is a race condition where one thread
is removing a control handler object from the requests list and
another thread is adding one. The result is that hdl->requests
is no longer empty and the code thinks that a main handler is
being freed instead of a control handler that is part of a request.
There are two bugs here: first the test for hdl->req_obj.req: this
should be hdl->req_obj.ops since only the main control handler will
have a NULL pointer there.
The second is that adding or deleting request objects from the
requests list of the main handler isn't protected by taking the
main handler's lock.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Reported-by: John Cox <jc@kynesim.co.uk> Fixes: 6fa6f831f095 ("media: v4l2-ctrls: add core request support") Tested-by: John Cox <jc@kynesim.co.uk> Reported-by: John Cox <jc@kynesim.co.uk> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
If ANA is enabled but no ANA group descriptor is found when creating
a new namespace the ANA log is most likely out of date, so trigger
a re-read. The namespace will be tagged with the NS_ANA_PENDING flag
to exclude it from path selection until the ANA log has been re-read.
Fixes: 32acab3181c7 ("nvme: implement multipath access to nvme subsystems") Reported-by: Martin George <marting@netapp.com> Signed-off-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Keith Busch <kbusch@kernel.org> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
We are not changing anything in the TCP connection state so
we should not take a write_lock but rather a read lock.
This caused a deadlock when running nvmet-tcp and nvme-tcp
on the same system, where state_change callbacks on the
host and on the controller side have causal relationship
and made lockdep report on this with blktests:
================================
WARNING: inconsistent lock state
5.12.0-rc3 #1 Tainted: G I
--------------------------------
inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-R} usage.
nvme/1324 [HC0[0]:SC0[0]:HE1:SE1] takes: ffff888363151000 (clock-AF_INET){++-?}-{2:2}, at: nvme_tcp_state_change+0x21/0x150 [nvme_tcp]
{IN-SOFTIRQ-W} state was registered at:
__lock_acquire+0x79b/0x18d0
lock_acquire+0x1ca/0x480
_raw_write_lock_bh+0x39/0x80
nvmet_tcp_state_change+0x21/0x170 [nvmet_tcp]
tcp_fin+0x2a8/0x780
tcp_data_queue+0xf94/0x1f20
tcp_rcv_established+0x6ba/0x1f00
tcp_v4_do_rcv+0x502/0x760
tcp_v4_rcv+0x257e/0x3430
ip_protocol_deliver_rcu+0x69/0x6a0
ip_local_deliver_finish+0x1e2/0x2f0
ip_local_deliver+0x1a2/0x420
ip_rcv+0x4fb/0x6b0
__netif_receive_skb_one_core+0x162/0x1b0
process_backlog+0x1ff/0x770
__napi_poll.constprop.0+0xa9/0x5c0
net_rx_action+0x7b3/0xb30
__do_softirq+0x1f0/0x940
do_softirq+0xa1/0xd0
__local_bh_enable_ip+0xd8/0x100
ip_finish_output2+0x6b7/0x18a0
__ip_queue_xmit+0x706/0x1aa0
__tcp_transmit_skb+0x2068/0x2e20
tcp_write_xmit+0xc9e/0x2bb0
__tcp_push_pending_frames+0x92/0x310
inet_shutdown+0x158/0x300
__nvme_tcp_stop_queue+0x36/0x270 [nvme_tcp]
nvme_tcp_stop_queue+0x87/0xb0 [nvme_tcp]
nvme_tcp_teardown_admin_queue+0x69/0xe0 [nvme_tcp]
nvme_do_delete_ctrl+0x100/0x10c [nvme_core]
nvme_sysfs_delete.cold+0x8/0xd [nvme_core]
kernfs_fop_write_iter+0x2c7/0x460
new_sync_write+0x36c/0x610
vfs_write+0x5c0/0x870
ksys_write+0xf9/0x1d0
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xae
irq event stamp: 10687
hardirqs last enabled at (10687): [<ffffffff9ec376bd>] _raw_spin_unlock_irqrestore+0x2d/0x40
hardirqs last disabled at (10686): [<ffffffff9ec374d8>] _raw_spin_lock_irqsave+0x68/0x90
softirqs last enabled at (10684): [<ffffffff9f000608>] __do_softirq+0x608/0x940
softirqs last disabled at (10649): [<ffffffff9cdedd31>] do_softirq+0xa1/0xd0
other info that might help us debug this:
Possible unsafe locking scenario:
Iff platform_get_irq() returns 0, ahci_platform_init_host() would return 0
early (as if the call was successful). Override IRQ0 with -EINVAL instead
as the 'libata' regards 0 as "no IRQ" (thus polling) anyway...
Fixes: c034640a32f8 ("ata: libahci: properly propagate return value of platform_get_irq()") Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru> Link: https://lore.kernel.org/r/4448c8cc-331f-2915-0e17-38ea34e251c8@omprussia.ru Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The function mv_platform_probe() neglects to check the results of the
calls to platform_get_irq() and irq_of_parse_and_map() and blithely
passes them to ata_host_activate() -- while the latter only checks
for IRQ0 (treating it as a polling mode indicattion) and passes the
negative values to devm_request_irq() causing it to fail as it takes
unsigned values for the IRQ #...
Add to mv_platform_probe() the proper IRQ checks to pass the positive IRQ
#s to ata_host_activate(), propagate upstream the negative error codes,
and override the IRQ0 with -EINVAL (as we don't want the polling mode).
Fixes: f351b2d638c3 ("sata_mv: Support SoC controllers") Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru> Link: https://lore.kernel.org/r/51436f00-27a1-e20b-c21b-0e817e0a7c86@omprussia.ru Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The driver's probe() method is written as if platform_get_irq() returns 0
on error, while actually it returns a negative error code (with all the
other values considered valid IRQs). Rewrite the driver's IRQ checking
code to pass the positive IRQ #s to ata_host_activate(), propagate errors
upstream, and treat IRQ0 as error, returning -EINVAL, as the libata code
treats 0 as an indication that polling should be used anyway...
The driver's probe() method is written as if platform_get_irq() returns 0
on error, while actually it returns a negative error code (with all the
other values considered valid IRQs). Rewrite the driver's IRQ checking code
to pass the positive IRQ #s to ata_host_activate(), propagate upstream
-EPROBE_DEFER, and set up the driver to polling mode on (negative) errors
and IRQ0 (libata treats IRQ #0 as a polling mode anyway)...
Fixes: a480167b23ef ("pata_arasan_cf: Adding support for arasan compact flash host controller") Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
There are 2 bugs in the can_boost() function because of using
x86 insn decoder. Since the insn->opcode never has a prefix byte,
it can not find CS override prefix in it. And the insn->attr is
the attribute of the opcode, thus inat_is_address_size_prefix(
insn->attr) always returns false.
Fix those by checking each prefix bytes with for_each_insn_prefix
loop and getting the correct attribute for each prefix byte.
Also, this removes unlikely, because this is a slow path.
Using 'imply AMD_IOMMU_V2' does not guarantee that the driver can link
against the exported functions. If the GPU driver is built-in but the
IOMMU driver is a loadable module, the kfd_iommu.c file is indeed
built but does not work:
x86_64-linux-ld: drivers/gpu/drm/amd/amdkfd/kfd_iommu.o: in function `kfd_iommu_bind_process_to_device':
kfd_iommu.c:(.text+0x516): undefined reference to `amd_iommu_bind_pasid'
x86_64-linux-ld: drivers/gpu/drm/amd/amdkfd/kfd_iommu.o: in function `kfd_iommu_unbind_process':
kfd_iommu.c:(.text+0x691): undefined reference to `amd_iommu_unbind_pasid'
x86_64-linux-ld: drivers/gpu/drm/amd/amdkfd/kfd_iommu.o: in function `kfd_iommu_suspend':
kfd_iommu.c:(.text+0x966): undefined reference to `amd_iommu_set_invalidate_ctx_cb'
x86_64-linux-ld: kfd_iommu.c:(.text+0x97f): undefined reference to `amd_iommu_set_invalid_ppr_cb'
x86_64-linux-ld: kfd_iommu.c:(.text+0x9a4): undefined reference to `amd_iommu_free_device'
x86_64-linux-ld: drivers/gpu/drm/amd/amdkfd/kfd_iommu.o: in function `kfd_iommu_resume':
kfd_iommu.c:(.text+0xa9a): undefined reference to `amd_iommu_init_device'
x86_64-linux-ld: kfd_iommu.c:(.text+0xadc): undefined reference to `amd_iommu_set_invalidate_ctx_cb'
x86_64-linux-ld: kfd_iommu.c:(.text+0xaff): undefined reference to `amd_iommu_set_invalid_ppr_cb'
x86_64-linux-ld: kfd_iommu.c:(.text+0xc72): undefined reference to `amd_iommu_bind_pasid'
x86_64-linux-ld: kfd_iommu.c:(.text+0xe08): undefined reference to `amd_iommu_set_invalidate_ctx_cb'
x86_64-linux-ld: kfd_iommu.c:(.text+0xe26): undefined reference to `amd_iommu_set_invalid_ppr_cb'
x86_64-linux-ld: kfd_iommu.c:(.text+0xe42): undefined reference to `amd_iommu_free_device'
Use IS_REACHABLE to only build IOMMU-V2 support if the amd_iommu symbols
are reachable by the amdkfd driver. Output a warning if they are not,
because that may not be what the user was expecting.
Fixes: 64d1c3a43a6f ("drm/amdkfd: Centralize IOMMUv2 code and make it conditional") Reported-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
There a 3 array for-loops that don't check the upper bounds of the
index into arrays and this may lead to potential out-of-bounds
reads. Fix this by adding array size upper bounds checks to be
full safe.
Addresses-Coverity: ("Out-of-bounds read")
Link: https://lore.kernel.org/linux-media/20201007121628.20676-1-colin.king@canonical.com Fixes: 333829110f1d ("[media] m88rs6000t: add new dvb-s/s2 tuner for integrated chip M88RS6000") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When sun6i_video_remote_subdev() returns NULL to subdev, no error return
code of sun6i_video_start_streaming() is assigned.
To fix this bug, ret is assigned with -EINVAL in this case.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn> Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com> Fixes: 5cc7522d8965 ("media: sun6i: Add support for Allwinner CSI V3s") Acked-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Video engine uses eclk and vclk for its clock sources and its reset
control is coupled with eclk so the current clock enabling sequence works
like below.
Enable eclk
De-assert Video Engine reset
10ms delay
Enable vclk
It introduces improper reset on the Video Engine hardware and eventually
the hardware generates unexpected DMA memory transfers that can corrupt
memory region in random and sporadic patterns. This issue is observed
very rarely on some specific AST2500 SoCs but it causes a critical
kernel panic with making a various shape of signature so it's extremely
hard to debug. Moreover, the issue is observed even when the video
engine is not actively used because udevd turns on the video engine
hardware for a short time to make a query in every boot.
To fix this issue, this commit changes the clock handling logic to make
the reset de-assertion triggered after enabling both eclk and vclk. Also,
it adds clk_unprepare call for a case when probe fails.
clk: ast2600: fix reset settings for eclk and vclk
Video engine reset setting should be coupled with eclk to match it
with the setting for previous Aspeed SoCs which is defined in
clk-aspeed.c since all Aspeed SoCs are sharing a single video engine
driver. Also, reset bit 6 is defined as 'Video Engine' reset in
datasheet so it should be de-asserted when eclk is enabled. This
commit fixes the setting.
Fixes: d2b4387f3bdf ("media: platform: Add Aspeed Video Engine driver") Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Reviewed-by: Eddie James <eajames@linux.ibm.com> Fixes: d3d04f6c330a ("clk: Add support for AST2600 SoC") Reviewed-by: Joel Stanley <joel@jms.id.au> Acked-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Currently the chroma_flags and alpha_flags are being zero'd with a bit-wise
mask and the following statement should be bit-wise or'ing in the new flag
bits but instead is making a direct assignment. Fix this by using the |=
operator rather than an assignment.
Addresses-Coverity: ("Unused value")
Fixes: ef834f7836ec ("[media] vivid: add the video capture and output parts") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The intent here was to return negative error codes but it actually
returns positive values. The problem is that type promotion with
ternary operations is quite complicated.
"ret" is an int. "copied" is a u32. And the snoop_file_read() function
returns long. What happens is that "ret" is cast to u32 and becomes
positive then it's cast to long and it's still positive.
Fix this by removing the ternary so that "ret" is type promoted directly
to long.
Fixes: 3772e5da4454 ("drivers/misc: Aspeed LPC snoop output using misc chardev") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Joel Stanley <joel@jms.id.au> Reviewed-by: Patrick Venture <venture@google.com> Link: https://lore.kernel.org/r/YIE90PSXsMTa2Y8n@mwanda Link: https://lore.kernel.org/r/20210423000919.1249474-1-joel@jms.id.au' Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Prior to commit 4a8c31a1c6f5 ("xen/blkback: rework connect_ring() to avoid
inconsistent xenstore 'ring-page-order' set by malicious blkfront"), the
behaviour of xen-blkback when connecting to a frontend was:
- read 'ring-page-order'
- if not present then expect a single page ring specified by 'ring-ref'
- else expect a ring specified by 'ring-refX' where X is between 0 and
1 << ring-page-order
This was correct behaviour, but was broken by the afforementioned commit to
become:
- read 'ring-page-order'
- if not present then expect a single page ring (i.e. ring-page-order = 0)
- expect a ring specified by 'ring-refX' where X is between 0 and
1 << ring-page-order
- if that didn't work then see if there's a single page ring specified by
'ring-ref'
This incorrect behaviour works most of the time but fails when a frontend
that sets 'ring-page-order' is unloaded and replaced by one that does not
because, instead of reading 'ring-ref', xen-blkback will read the stale
'ring-ref0' left around by the previous frontend will try to map the wrong
grant reference.
This patch restores the original behaviour.
Fixes: 4a8c31a1c6f5 ("xen/blkback: rework connect_ring() to avoid inconsistent xenstore 'ring-page-order' set by malicious blkfront") Signed-off-by: Paul Durrant <pdurrant@amazon.com> Reviewed-by: Dongli Zhang <dongli.zhang@oracle.com> Reviewed-by: "Roger Pau Monné" <roger.pau@citrix.com> Link: https://lore.kernel.org/r/20210202175659.18452-1-paul@xen.org Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
int main(int argc, char *argv[])
{
int i;
int fd[10];
for (i = 0; i < 10; i++)
fd[i] = open("/dev/ttyprintk", O_WRONLY);
ioctl(fd[0], TIOCVHANGUP);
for (i = 0; i < 10; i++)
close(fd[i]);
close(open("/dev/ttyprintk", O_WRONLY));
return 0;
}
----------
When TTY hangup happens, port->count needs to be reset via
"struct tty_operations"->hangup callback.
When core is in hibernation in host mode and a device cable
was connected then driver exited from device hibernation.
However, registers saved for host mode and when exited from
device hibernation register restore would be done for device
register which was wrong because there was no device registers
stored to restore.
- Added dwc_handle_gpwrdn_disc_det() function which handles
gpwrdn disconnect detect flow and exits hibernation
without restoring the registers.
- Updated exiting from hibernation in GPWRDN_STS_CHGINT with
calling dwc_handle_gpwrdn_disc_det() function. Here no register
is restored which is the solution described above.
Added setting "port_connect_status_change" flag to "1" in order
to re-enumerate, because after exit from hibernation port
connection status is not detected.
arch/x86/platform/uv/uv_nmi.c:875:14: error: ‘uv_nmi_kexec_failed’ undeclared (first use in this function)
Since uv_nmi_kexec_failed is only defined in the KEXEC_CORE #ifdef branch,
this code cannot ever have been build tested:
if (main)
pr_err("UV: NMI kdump: KEXEC not supported in this kernel\n");
atomic_set(&uv_nmi_kexec_failed, 1);
Nor is this use possible in uv_handle_nmi():
atomic_set(&uv_nmi_kexec_failed, 0);
These bugs were introduced in this commit:
d0a9964e9873: ("x86/platform/uv: Implement simple dump failover if kdump fails")
Which added the uv_nmi_kexec_failed assignments to !KEXEC code, while making the
definition KEXEC-only - apparently without testing the !KEXEC case.
Instead of complicating the #ifdef maze, simplify the code by requiring X86_UV
to depend on KEXEC_CORE. This pattern is present in other architectures as well.
( We'll remove the untested, 7 years old !KEXEC complications from the file in a
separate commit. )
Fixes: d0a9964e9873: ("x86/platform/uv: Implement simple dump failover if kdump fails") Signed-off-by: Ingo Molnar <mingo@kernel.org> Cc: Mike Travis <travis@sgi.com> Cc: linux-kernel@vger.kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
pmc_plt_clk* clocks are used for ethernet controllers, so need to stay
turned on. This adds the affected board family to critclk_systems DMI
table, so the clocks are marked as CLK_CRITICAL and not turned off.
This replaces the previously listed boards with a match for the whole
device family CBxx63. CBxx63 matches only baytrail devices.
There are new affected boards that would otherwise need to be listed.
There are unaffected boards in the family, but having the clocks
turned on is not an issue.
Fixes: 648e921888ad ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL") Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com> Link: https://lore.kernel.org/r/20210412133006.397679-1-linux-kernel-dev@beckhoff.com Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
We can't use kfree() to free device managed resources so the kfree(dev)
is against the rules.
It's easier to write this code if we open code the device_register() as
a device_initialize() and device_add(). That way if dev_set_name() set
name fails we can call put_device() and it will clean up correctly.
When CONFIG_QCOM_SCM is y and CONFIG_HAVE_ARM_SMCCC
is not set, compiling errors are encountered as follows:
drivers/firmware/qcom_scm-smc.o: In function `__scm_smc_do_quirk':
qcom_scm-smc.c:(.text+0x36): undefined reference to `__arm_smccc_smc'
drivers/firmware/qcom_scm-legacy.o: In function `scm_legacy_call':
qcom_scm-legacy.c:(.text+0xe2): undefined reference to `__arm_smccc_smc'
drivers/firmware/qcom_scm-legacy.o: In function `scm_legacy_call_atomic':
qcom_scm-legacy.c:(.text+0x1f0): undefined reference to `__arm_smccc_smc'
Note that __arm_smccc_smc is defined when HAVE_ARM_SMCCC is y.
So add dependency on HAVE_ARM_SMCCC in QCOM_SCM configuration.
Fixes: 916f743da354 ("firmware: qcom: scm: Move the scm driver to drivers/firmware") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: He Ying <heying24@huawei.com> Link: https://lore.kernel.org/r/20210406094200.60952-1-heying24@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Drivers can return -ENOIOCTLCMD when an ioctl is not recognised to tell
the upper layers to continue looking for a handler.
This is not the case for the RS485 and ISO7816 ioctls whose handlers
should return -ENOTTY directly in case a serial driver does not
implement the corresponding methods.
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The xmit_fifo_size parameter could be used to set the hardware transmit
fifo size of a legacy UART when it could not be detected, but the
interface is limited to eight bits and should be left unset when it is
not used.
Similarly, baud_base could be used to set the UART base clock when it
could not be detected, but might as well be left unset when it is not
known (which is the case for CDC).
Fix the cdc-acm TIOCGSERIAL implementation by dropping its custom
interpretation of the unused xmit_fifo_size and baud_base fields, which
overflowed the former with the URB buffer size and set the latter to the
current line speed. Also return the port line number, which is the only
other value used besides the close parameters.
Note that the current line speed can still be retrieved through the
standard termios interfaces.
Fixes: 18c75720e667 ("USB: allow users to run setserial with cdc-acm") Acked-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20210408131602.27956-4-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
A non-privileged user has only ever been able to set the since long
deprecated ASYNC_SPD flags and trying to change any other *supported*
feature should result in -EPERM being returned. Setting the current
values for any supported features should return success.
Fix the cdc-acm implementation which instead indicated that the
TIOCSSERIAL ioctl was not even implemented when a non-privileged user
set the current values.
Fixes: ba2d8ce9db0a ("cdc-acm: implement TIOCSSERIAL to avoid blocking close(2)") Acked-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20210408131602.27956-3-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Fixes: 944c01a889d9 ("spi: lpspi: enable runtime pm for lpspi") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Li <wangli74@huawei.com> Link: https://lore.kernel.org/r/20210409095430.29868-1-wangli74@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When current CPU load is not L0 then loading armada-37xx-cpufreq.ko driver
fails with following error:
# modprobe armada-37xx-cpufreq
[ 502.702097] Unsupported CPU frequency 250 MHz
This issue was partially fixed by commit 8db82563451f ("cpufreq:
armada-37xx: fix frequency calculation for opp"), but only for calculating
CPU frequency for opp.
Fix this also for determination of base CPU frequency.
Signed-off-by: Pali Rohár <pali@kernel.org> Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com> Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com> Tested-by: Anders Trier Olesen <anders.trier.olesen@gmail.com> Tested-by: Philip Soares <philips@netisense.com> Fixes: 92ce45fb875d ("cpufreq: Add DVFS support for Armada 37xx") Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Commit 8db82563451f ("cpufreq: armada-37xx: fix frequency calculation for
opp") changed calculation of frequency passed to the dev_pm_opp_add()
function call. But the code for dev_pm_opp_remove() function call was not
updated, so the driver cleanup phase does not work when registration fails.
This fixes the issue by using the same frequency in both calls.
Signed-off-by: Pali Rohár <pali@kernel.org> Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com> Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com> Tested-by: Anders Trier Olesen <anders.trier.olesen@gmail.com> Tested-by: Philip Soares <philips@netisense.com> Fixes: 8db82563451f ("cpufreq: armada-37xx: fix frequency calculation for opp") Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
projects / mirror_ubuntu-focal-kernel.git / log