Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com> Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net>
1) Fix stack allocation in s390 BPF JIT, from Michael Holzheu.
2) Disable LRO on openvswitch paths, from Jiri Benc.
3) UDP early demux doesn't handle multicast group membership properly,
fix from Shawn Bohrer.
4) Fix TX queue hang due to incorrect handling of mixed sized fragments
and linearlization in i40e driver, from Anjali Singhai Jain.
5) Cannot use disable_irq() in timer handler of AMD xgbe driver, from
Thomas Lendacky.
6) b2net driver improperly assumes pci_alloc_consistent() gives zero'd
out memory, use dma_zalloc_coherent(). From Sriharsha Basavapatna.
7) Fix use-after-free in MPLS and ipv6, from Robert Shearman.
8) Missing neif_napi_del() calls in cleanup paths of b44 driver, from
Hauke Mehrtens.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: replace last open coded skb_orphan_frags with function call
net: bcmgenet: power on MII block for all MII modes
ipv6: Fix protocol resubmission
ipv6: fix possible use after free of dev stats
b44: call netif_napi_del()
bridge: disable softirqs around br_fdb_update to avoid lockup
Revert "bridge: use _bh spinlock variant for br_fdb_update to avoid lockup"
mpls: fix possible use after free of device
be2net: Replace dma/pci_alloc_coherent() calls with dma_zalloc_coherent()
bridge: use _bh spinlock variant for br_fdb_update to avoid lockup
amd-xgbe: Use disable_irq_nosync from within timer function
rhashtable: add missing import <linux/export.h>
i40e: Make sure to be in VEB mode if SRIOV is enabled at probe
i40e: start up in VEPA mode by default
i40e/i40evf: Fix mixed size frags and linearization
ipv4/udp: Verify multicast group is ours in upd_v4_early_demux()
openvswitch: disable LRO
s390/bpf: fix bpf frame pointer setup
s390/bpf: fix stack allocation
Linus Torvalds [Mon, 8 Jun 2015 23:26:53 +0000 (16:26 -0700)]
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull last-minute virtio fix from Michael Tsirkin:
"This fixes a minor issue affecting multiqueue virtio net when user
keeps changing the number of active queues and CPUs are added and
removed by hotplug"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_pci: Clear stale cpumask when setting irq affinity
Dan Murphy [Mon, 8 Jun 2015 19:30:55 +0000 (14:30 -0500)]
net: phy: dp83867: Fix device tree entries
Fix the device tree entries to modify the '_' to '-'.
Also changes the names of the internal delay properties
from -int- to -internal- as the -int- appeared as a keyword.
Signed-off-by: Dan Murphy <dmurphy@ti.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
API compliance scanning with coccinelle flagged:
./drivers/atm/iphase.c:2621:4-20:
WARNING: timeout (50) seems HZ dependent
Numeric constants passed to schedule_timeout() make the effective
timeout HZ dependent which does not seem intended.
Fixed up by converting the constant to jiffies with msecs_to_jiffies()
As this driver was introduced in the early 2.3 series it is most
likely assuming HZ=100 so the constant 50 is converted to 500ms.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 8 Jun 2015 20:21:58 +0000 (13:21 -0700)]
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Kevin Hilman:
"About 10 days worth of small bug fixes, and the (hopefully) final
round fixes for from arm-soc land for the -rc cycle. Nothing special
to note, but here's a brief summary of fixes by SoC type:
- OMAP:
small set of misc DT fixes; boot fix for THUMB2 kernel
- mediatek:
PMIC fixes; DT fix for model name
- exynos:
wakeup interupt fixes for 3250
- mvebu:
revert mbus patch which broke DMA masters
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: am335x-boneblack: disable RTC-only sleep to avoid hardware damage
ARM: dts: AM35xx: fix system control module clocks
arm64: dts: mt8173-evb: fix model name
ARM: exynos: Fix wake-up interrupts for Exynos3250
ARM: dts: Fix n900 dts file to work around 4.1 touchscreen regression on n900
ARM: dts: Fix dm816x to use right compatible flag for MUSB
ARM: OMAP3: Fix booting with thumb2 kernel
Revert "bus: mvebu-mbus: make sure SDRAM CS for DMA don't overlap the MBus bridge window"
bus: mvebu-mbus: do not set WIN_CTRL_SYNCBARRIER on non io-coherent platforms.
ARM: mvebu: armada-xp-linksys-mamba: Disable internal RTC
soc: mediatek: Add compile dependency to pmic-wrapper
soc: mediatek: PMIC wrap: Fix register state machine handling
soc: mediatek: PMIC wrap: Fix clock rate handling
net: phy: bcm7xxx: update workaround to fix 100BaseT corner cases
Update the AFE_TX_CONFIG value to solve marginal rise/fall issues
observed when the link is operating in 100BaseT. This workaround applies
to GPHY revisions D0, E0 and newer.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: replace last open coded skb_orphan_frags with function call
Commit 70008aa50e92 ("skbuff: convert to skb_orphan_frags") replaced
open coded tests of SKBTX_DEV_ZEROCOPY and skb_copy_ubufs with calls
to helper function skb_orphan_frags. Apply that to the last remaining
open coded site.
Signed-off-by: Willem de Bruijn <willemb@google.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: bcmgenet: power on MII block for all MII modes
The RGMII block is currently only powered on when using RGMII or
RGMII_NO_ID, which is not correct when using the GENET interface in MII
or Reverse MII modes. We always need to power on the RGMII interface for
this block to properly work, regardless of the MII mode in which we
operate.
Fixes: aa09677cba423 ("net: bcmgenet: add MDIO routines") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Josh Hunt [Mon, 8 Jun 2015 16:00:59 +0000 (12:00 -0400)]
ipv6: Fix protocol resubmission
UDP encapsulation is broken on IPv6. This is because the logic to resubmit
the nexthdr is inverted, checking for a ret value > 0 instead of < 0. Also,
the resubmit label is in the wrong position since we already get the
nexthdr value when performing decapsulation. In addition the skb pull is no
longer necessary either.
This changes the return value check to look for < 0, using it for the
nexthdr on the next iteration, and moves the resubmit label to the proper
location.
With these changes the v6 code now matches what we do in the v4 ip input
code wrt resubmitting when decapsulating.
Signed-off-by: Josh Hunt <johunt@akamai.com> Acked-by: "Tom Herbert" <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Shearman [Fri, 5 Jun 2015 17:51:54 +0000 (18:51 +0100)]
ipv6: fix possible use after free of dev stats
The memory pointed to by idev->stats.icmpv6msgdev,
idev->stats.icmpv6dev and idev->stats.ipv6 can each be used in an RCU
read context without taking a reference on idev. For example, through
IP6_*_STATS_* calls in ip6_rcv. These memory blocks are freed without
waiting for an RCU grace period to elapse. This could lead to the
memory being written to after it has been freed.
Fix this by using call_rcu to free the memory used for stats, as well
as idev after an RCU grace period has elapsed.
Signed-off-by: Robert Shearman <rshearma@brocade.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Kevin Hilman [Mon, 8 Jun 2015 17:31:34 +0000 (10:31 -0700)]
Merge tag 'omap-for-v4.1/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge omap fixes for v4.1, urgent fix to avoid potential hardware damage From Tony Lindgren:
Omap fixes for the -rc cycle, including a fix for potential hardware
breakage on BeagleBones:
- BeagleBones don't support RTC-only mode, it can cause hardware
damage if system-power-controller is specified without
ti,pmic-shutdown-controller
- Fix a recent regression to am3517 SoCs caused by the recent clock
move that was not noticed until now despite automated boot
testing
- Fix a regression for n900 touchscreen triggered by recent
recent input changes
- Fix compatible property for dm816x USB to avoid errors with
USB Ethernet
- Fix oops for omap3 when built with CONFIG_THUMB2_KERNEL
* tag 'omap-for-v4.1/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-boneblack: disable RTC-only sleep to avoid hardware damage
ARM: dts: AM35xx: fix system control module clocks
ARM: dts: Fix n900 dts file to work around 4.1 touchscreen regression on n900
ARM: dts: Fix dm816x to use right compatible flag for MUSB
ARM: OMAP3: Fix booting with thumb2 kernel
Linus Torvalds [Mon, 8 Jun 2015 16:37:23 +0000 (09:37 -0700)]
Merge git://git.infradead.org/intel-iommu
Pull Intel IOMMU fix from David Woodhouse:
"This fixes an oops when attempting to enable 1:1 passthrough mode for
devices on which VT-d translation was disabled anyway.
It's actually a long-standing bug but recent changes (commit 18436afdc11a: "iommu/vt-d: Allow RMRR on graphics devices too") have
made it much easier to trigger with 'iommu=pt intel_iommu=igfx_off' on
the command line"
* git://git.infradead.org/intel-iommu:
iommu/vt-d: Fix passthrough mode with translation-disabled devices
Linus Torvalds [Mon, 8 Jun 2015 15:47:08 +0000 (08:47 -0700)]
Merge branch 'for-4.1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"Two driver fixes. One is for an ahci_mvebu controller config bug and
the other fixes pata_octeon_cf build issue"
* 'for-4.1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
pata_octeon_cf: fix broken build
ata: ahci_mvebu: Fix wrongly set base address for the MBus window setting
David S. Miller [Mon, 8 Jun 2015 07:50:49 +0000 (00:50 -0700)]
Merge branch 'phy-micrel'
Jaeden Amero says:
====================
net/phy: micrel: Center FLP timing at 16ms
In v2, we add an additional cleanup commit to make an array of strings
static const and to improve const correctness generally. We also no longer
unnecessarily initialize the result variable in
ksz9031_center_flp_timing().
In v3, we remove the unnecessary result variable from ksz9031_config_init()
introduced by a previous version of "net/phy: micrel: Center FLP timing at
16ms".
In v4, we modify the commit message of "net/phy: micrel: Center FLP timing
at 16ms" to replace the awkward quotation of the data sheet's programming
procedure with an explanation of why we program the FLP burst registers and
restart auto-negotiation where we do (config_init).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jaeden Amero [Fri, 5 Jun 2015 23:00:26 +0000 (18:00 -0500)]
net/phy: micrel: Center FLP timing at 16ms
Link failures have been observed when using the KSZ9031 with HP 1810-8G
and HP 1910-8G network switches. Center the FLP timing at 16ms to help
avoid intermittent link failures.
>From the KSZ9031RNX and KSZ9031MNX data sheets revision 2.2, section
"Auto-Negotiation Timing":
The KSZ9031[RNX or MNX] Fast Link Pulse (FLP) burst-to-burst
transmit timing for Auto-Negotiation defaults to 8ms. IEEE 802.3
Standard specifies this timing to be 16ms +/-8ms. Some PHY link
partners need to receive the FLP with 16ms centered timing;
otherwise, there can be intermittent link failures and long
link-up times.
The PHY data sheet recommends configuring the FLP burst registers after
power-up/reset and immediately thereafter restarting auto-negotiation, so
we center the FLP timing at 16ms and then restart auto-negotiation in the
config_init for KSZ9031.
Signed-off-by: Jaeden Amero <jaeden.amero@ni.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Firo Yang [Mon, 8 Jun 2015 03:54:51 +0000 (11:54 +0800)]
fib_trie: coding style: Use pointer after check
As Alexander Duyck pointed out that:
struct tnode {
...
struct key_vector kv[1];
}
The kv[1] member of struct tnode is an arry that refernced by
a null pointer will not crash the system, like this:
struct tnode *p = NULL;
struct key_vector *kv = p->kv;
As such p->kv doesn't actually dereference anything, it is simply a
means for getting the offset to the array from the pointer p.
This patch make the code more regular to avoid making people feel
odd when they look at the code.
Signed-off-by: Firo Yang <firogm@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Numeric constants passed to schedule_timeout_*() make the effective
timeout HZ dependent which does not seem to be the intent here.
Fixed up by converting the constant to jiffies with msecs_to_jiffies(),
passing 100ms (assuming HZ==100 in the original code).
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Signed-off-by: David S. Miller <davem@davemloft.net>
API compliance scanning with coccinelle flagged:
./drivers/net/wan/cosa.c:520:2-18: WARNING:
timeout (30) seems HZ dependent
Numeric constants passed to schedule_timeout() make the effective
timeout HZ dependent which makes little sense in a device probe.
Fixed up by converting the constant to jiffies with msecs_to_jiffies()
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Majd Dibbiny [Sun, 7 Jun 2015 12:44:23 +0000 (15:44 +0300)]
net/mlx5_core: Fix static checker warnings around system guid query flow
Fix static checker warnings in the flow of system guid query.
Fixes: 707c4602cda6 ('net/mlx5_core: Add new query HCA vport commands') Signed-off-by: Majd Dibbiny <majd@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bridge: disable softirqs around br_fdb_update to avoid lockup
br_fdb_update() can be called in process context in the following way:
br_fdb_add() -> __br_fdb_add() -> br_fdb_update() (if NTF_USE flag is set)
so we need to disable softirqs because there are softirq users of the
hash_lock. One easy way to reproduce this is to modify the bridge utility
to set NTF_USE, enable stp and then set maxageing to a low value so
br_fdb_cleanup() is called frequently and then just add new entries in
a loop. This happens because br_fdb_cleanup() is called from timer/softirq
context. The spin locks in br_fdb_update were _bh before commit f8ae737deea1
("[BRIDGE]: forwarding remove unneeded preempt and bh diasables")
and at the time that commit was correct because br_fdb_update() couldn't be
called from process context, but that changed after commit: 292d1398983f ("bridge: add NTF_USE support")
Using local_bh_disable/enable around br_fdb_update() allows us to keep
using the spin_lock/unlock in br_fdb_update for the fast-path.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Fixes: 292d1398983f ("bridge: add NTF_USE support") Signed-off-by: David S. Miller <davem@davemloft.net>
isdn/hisax: Convert use of __constant_cpu_to_le16 to cpu_to_le16
In big endian cases, macro cpu_to_le16 unfolds to __swab16 which
provides special case for constants. In little endian cases,
__constant_cpu_to_le16 and cpu_to_le16 expand directly to the
same expression. So, replace __constant_cpu_to_le16 with
cpu_to_le16 with the goal of getting rid of the definition of
__constant_cpu_to_le16 completely.
The semantic patch that performs this transformation is as follows:
@@expression x;@@
- __constant_cpu_to_le16(x)
+ cpu_to_le16(x)
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Shearman [Fri, 5 Jun 2015 17:54:45 +0000 (18:54 +0100)]
mpls: fix possible use after free of device
The mpls device is used in an RCU read context without a lock being
held. As the memory is freed without waiting for the RCU grace period
to elapse, the freed memory could still be in use.
Address this by using kfree_rcu to free the memory for the mpls device
after the RCU grace period has elapsed.
Fixes: 03c57747a702 ("mpls: Per-device MPLS state") Signed-off-by: Robert Shearman <rshearma@brocade.com> Acked-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 7 Jun 2015 23:56:10 +0000 (16:56 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
"Eight fixes across arch/mips. Nothing stands particuarly out nor is
complicated but fixes keep coming in at a higher than comfortable
rate"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: KVM: Do not sign extend on unsigned MMIO load
MIPS: BPF: Fix stack pointer allocation
MIPS: Loongson-3: Fix a cpu-hotplug issue in loongson3_ipi_interrupt()
MIPS: Fix enabling of DEBUG_STACKOVERFLOW
MIPS: c-r4k: Fix typo in probe_scache()
MIPS: Avoid an FPE exception in FCSR mask probing
MIPS: ath79: Add a missing new line in log message
MIPS: ralink: Fix clearing the illegal access interrupt
be2net: Replace dma/pci_alloc_coherent() calls with dma_zalloc_coherent()
There are several places in the driver (all in control paths) where
coherent dma memory is being allocated using either dma_alloc_coherent()
or the deprecated pci_alloc_consistent(). All these calls should be
changed to use dma_zalloc_coherent() to avoid uninitialized fields in
data structures backed by this memory.
Reported-by: Joerg Roedel <jroedel@suse.de> Tested-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@avagotech.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fugang Duan [Fri, 5 Jun 2015 09:22:08 +0000 (17:22 +0800)]
net: fec: ptp: correct the ENET_ATCOR value
The current driver adjust freq formula is:
fe * diff = ppb * pc
Note:
fe: ENET ref clock frequency in Hz
diff = inc_corr - inc: difference between default increment and correction increment
ppb: parts per billion adjustment from base
pc: correction period (in number of fe clock cycles)
The correction increment will be used after N cycles of regular increments,
not every N cycles (with N being the correction period). For example, set ENET_ATCOR=4,
INC=8, INC_CORR=9, there will be 4 increments of 8 (ENET_ATINC[INC]) , followed by 1
increment of 9 (ENET_ATINC[INC_CORR]).
So, the correct formula is:
fe * diff = ppb * (pc + 1)
For ENET_ATCOR, a value 0 disables the correction counter and no corrections occur.
So base on the origin formula, set pc = pc > 1 ? pc - 1 : pc.
Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Frank Li <Frank.Li@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wilson Kok [Fri, 5 Jun 2015 07:52:57 +0000 (00:52 -0700)]
bridge: use _bh spinlock variant for br_fdb_update to avoid lockup
br_fdb_update() can be called in process context in the following way:
br_fdb_add() -> __br_fdb_add() -> br_fdb_update() (if NTF_USE flag is set)
so we need to use spin_lock_bh because there are softirq users of the
hash_lock. One easy way to reproduce this is to modify the bridge utility
to set NTF_USE, enable stp and then set maxageing to a low value so
br_fdb_cleanup() is called frequently and then just add new entries in
a loop. This happens because br_fdb_cleanup() is called from timer/softirq
context. These locks were _bh before commit f8ae737deea1
("[BRIDGE]: forwarding remove unneeded preempt and bh diasables")
and at the time that commit was correct because br_fdb_update() couldn't be
called from process context, but that changed after commit: 292d1398983f ("bridge: add NTF_USE support")
Signed-off-by: Wilson Kok <wkok@cumulusnetworks.com> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Fixes: 292d1398983f ("bridge: add NTF_USE support") Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Simek [Fri, 5 Jun 2015 08:49:17 +0000 (10:49 +0200)]
net: ll_temac: Remove sparse warnings
Remove sparse warnings:
drivers/net/ethernet/xilinx/ll_temac_main.c:65:16: warning: cast removes
address space of expression
drivers/net/ethernet/xilinx/ll_temac_main.c:70:9: warning: cast removes
address space of expression
drivers/net/ethernet/xilinx/ll_temac_main.c:127:16: warning: cast
removes address space of expression
drivers/net/ethernet/xilinx/ll_temac_main.c:137:9: warning: cast removes
address space of expression
drivers/net/ethernet/xilinx/ll_temac_main.c:409:3: warning: symbol
'temac_options' was not declared. Should it be static?
drivers/net/ethernet/xilinx/ll_temac_main.c:590:6: warning: symbol
'temac_adjust_link' was not declared. Should it be static?
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dump useful ring statistics along with interrupt status, software
maintained pointers and hardware registers to help troubleshoot TX queue
stalls.
When a timeout occurs, disable TX NAPI for the rings, dump their states
while interrupts are disabled, re-enable interrupts, NAPI and queue flow
control to help with the recovery.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Thu, 4 Jun 2015 23:10:09 +0000 (01:10 +0200)]
net: dsa: mv88e6xxx: Fix deadlock by double lock
ethtool -S on a DSA interface can deadlock for some switches because
the same lock is taken twice. Use the register read function which
expects the lock to be already held.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Fixes: 31888234b736 ("net: dsa: mv88e6xxx: Replace stats mutex with SMI mutex") Signed-off-by: David S. Miller <davem@davemloft.net>
bpf: allow programs to write to certain skb fields
allow programs read/write skb->mark, tc_index fields and
((struct qdisc_skb_cb *)cb)->data.
mark and tc_index are generically useful in TC.
cb[0]-cb[4] are primarily used to pass arguments from one
program to another called via bpf_tail_call() which can
be seen in sockex3_kern.c example.
All fields of 'struct __sk_buff' are readable to socket and tc_cls_act progs.
mark, tc_index are writeable from tc_cls_act only.
cb[0]-cb[4] are writeable by both sockets and tc_cls_act.
Add verifier tests and improve sample code.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bpf: make programs see skb->data == L2 for ingress and egress
eBPF programs attached to ingress and egress qdiscs see inconsistent skb->data.
For ingress L2 header is already pulled, whereas for egress it's present.
This is known to program writers which are currently forced to use
BPF_LL_OFF workaround.
Since programs don't change skb internal pointers it is safe to do
pull/push right around invocation of the program and earlier taps and
later pt->func() will not be affected.
Multiple taps via packet_rcv(), tpacket_rcv() are doing the same trick
around run_filter/BPF_PROG_RUN even if skb_shared.
This fix finally allows programs to use optimized LD_ABS/IND instructions
without BPF_LL_OFF for higher performance.
tc ingress + cls_bpf + samples/bpf/tcbpf1_kern.o
w/o JIT w/JIT
before 20.5 23.6 Mpps
after 21.8 26.6 Mpps
Old programs with BPF_LL_OFF will still work as-is.
We can now undo most of the earlier workaround commit: a166151cbe33 ("bpf: fix bpf helpers to use skb->mac_header relative offsets")
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
amd-xgbe: Use disable_irq_nosync from within timer function
Since the Tx timer function runs in softirq context the driver needs
to call disable_irq_nosync instead of a disable_irq.
Reported-by: Josh Stone <jistone@redhat.com> Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fix:
drivers/net/wan/dscc4.c: In function 'dscc4_open':
drivers/net/wan/dscc4.c:1049:25: warning: variable 'ppriv' set but not used
[-Wunused-but-set-variable]
This has been in there unused since 1da177e4c3f (Linux-2.6.12-rc2) simply
remove it.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 7 Jun 2015 04:17:57 +0000 (21:17 -0700)]
inet: add IP_BIND_ADDRESS_NO_PORT to overcome bind(0) limitations
When an application needs to force a source IP on an active TCP socket
it has to use bind(IP, port=x).
As most applications do not want to deal with already used ports, x is
often set to 0, meaning the kernel is in charge to find an available
port.
But kernel does not know yet if this socket is going to be a listener or
be connected.
It has very limited choices (no full knowledge of final 4-tuple for a
connect())
With limited ephemeral port range (about 32K ports), it is very easy to
fill the space.
This patch adds a new SOL_IP socket option, asking kernel to ignore
the 0 port provided by application in bind(IP, port=0) and only
remember the given IP address.
The port will be automatically chosen at connect() time, in a way
that allows sharing a source port as long as the 4-tuples are unique.
This new feature is available for both IPv4 and IPv6 (Thanks Neal)
Tested:
Wrote a test program and checked its behavior on IPv4 and IPv6.
strace(1) shows sequences of bind(IP=127.0.0.2, port=0) followed by
connect().
Also getsockname() show that the port is still 0 right after bind()
but properly allocated after connect().
Linus Torvalds [Sun, 7 Jun 2015 05:37:45 +0000 (22:37 -0700)]
Merge tag 'driver-core-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are two fixes for the driver core that resolve some reported
issues.
One is a regression from 4.0, the other a fixes a reported oops that
has been there since 3.19.
Both have been in linux-next for a while with no problems"
* tag 'driver-core-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
drivers/base: cacheinfo: handle absence of caches
drivers: of/base: move of_init to driver_init
Linus Torvalds [Sun, 7 Jun 2015 05:33:08 +0000 (22:33 -0700)]
Merge tag 'staging-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging / IIO fixes from Greg KH:
"Here are some IIO driver fixes to resolve reported issues, some ozwpan
fixes for some reported CVE problems, and a rtl8712 driver fix for a
reported regression.
All have been in linux-next successfully"
* tag 'staging-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: rtl8712: fix stack dump
ozwpan: unchecked signed subtraction leads to DoS
ozwpan: divide-by-zero leading to panic
ozwpan: Use unsigned ints to prevent heap overflow
ozwpan: Use proper check to prevent heap overflow
iio: adc: twl6030-gpadc: Fix modalias
iio: adis16400: Fix burst transfer for adis16448
iio: adis16400: Fix burst mode
iio: adis16400: Compute the scan mask from channel indices
iio: adis16400: Use != channel indices for the two voltage channels
iio: adis16400: Report pressure channel scale
Linus Torvalds [Sun, 7 Jun 2015 05:14:23 +0000 (22:14 -0700)]
Merge tag 'tty-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are a few TTY and Serial driver fixes for reported regressions
and crashes.
All of these have been in linux-next with no reported problems"
* tag 'tty-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
n_tty: Fix auditing support for cannonical mode
serial: 8250_omap: provide complete custom startup & shutdown callbacks
n_tty: Fix calculation of size in canon_copy_from_read_buf
serial: imx: Fix DMA handling for IDLE condition aborts
serial/amba-pl011: Unconditionally poll for FIFO space before each TX char
Linus Torvalds [Sun, 7 Jun 2015 05:06:53 +0000 (22:06 -0700)]
Merge tag 'usb-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB and PHY driver fixes from Greg KH:
"Here are some USB and PHY driver fixes that resolve some reported
regressions. Also in here are some new device ids.
All of the details are in the shortlog and these patches have been in
linux-next with no problems"
* tag 'usb-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (22 commits)
USB: cp210x: add ID for HubZ dual ZigBee and Z-Wave dongle
usb: renesas_usbhs: Don't disable the pipe if Control write status stage
usb: renesas_usbhs: Fix fifo unclear in usbhsf_prepare_pop
usb: gadget: f_fs: fix check in read operation
usb: musb: fix order of conditions for assigning end point operations
usb: gadget: f_uac1: check return code from config_ep_by_speed
usb: gadget: ffs: fix: Always call ffs_closed() in ffs_data_clear()
usb: gadget: g_ffs: Fix counting of missing_functions
usb: s3c2410_udc: correct reversed pullup logic
usb: dwc3: gadget: Fix incorrect DEPCMD and DGCMD status macros
usb: phy: tahvo: Pass the IRQF_ONESHOT flag
usb: phy: ab8500-usb: Pass the IRQF_ONESHOT flag
usb: renesas_usbhs: Revise the binding document about the dma-names
usb: host: xhci: add mutex for non-thread-safe data
usb: make module xhci_hcd removable
USB: serial: ftdi_sio: Add support for a Motion Tracker Development Board
usb: gadget: f_midi: fix segfault when reading empty id
phy: phy-rcar-gen2: Fix USBHS_UGSTS_LOCK value
phy: omap-usb2: invoke pm_runtime_disable on error path
phy: fix Kconfig dependencies
...
Linus Torvalds [Sun, 7 Jun 2015 04:43:29 +0000 (21:43 -0700)]
Merge tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux
Pull devicetree fix from Grant Likely:
"Stupid typo fix for v4.1. One of the IS_ENABLED() macro calls forgot
the CONFIG_ prefix. Only affects a tiny number of platforms, but
still..."
* tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux:
of/dynamic: Fix test for PPC_PSERIES
Linus Torvalds [Sat, 6 Jun 2015 16:15:14 +0000 (09:15 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"i915 has a bunch of fixes, and Russell found a bug in sysfs writing
handling that results in userspace getting stuck"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm: fix writing to /sys/class/drm/*/status
drm/i915: Move WaBarrierPerformanceFixDisable:skl to skl code from chv code
drm/i915: Include G4X/VLV/CHV in self refresh status
drm/i915: Initialize HWS page address after GPU reset
drm/i915: Don't skip request retirement if the active list is empty
drm/i915/hsw: Fix workaround for server AUX channel clock divisor
Linus Torvalds [Sat, 6 Jun 2015 16:08:23 +0000 (09:08 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input subsystem fixes from Dmitry Torokhov:
"Just a couple touchpad drivers fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: alps - do not reduce trackpoint speed by half
Input: elantech - add new icbody type
Input: elantech - fix detection of touchpads where the revision matches a known rate
Markos Chandras [Thu, 4 Jun 2015 10:56:13 +0000 (11:56 +0100)]
MIPS: BPF: Fix stack pointer allocation
Fix stack pointer offset which could potentially corrupt
argument registers in the previous frame. The calculated offset
reflects the size of all the registers we need to preserve so there
is no need for this erroneous subtraction.
[ralf@linux-mips.org: Fixed conflict due to only applying this fix part
of the entire series as part of 4.1 fixes.]
Huacai Chen [Thu, 4 Jun 2015 06:53:47 +0000 (14:53 +0800)]
MIPS: Loongson-3: Fix a cpu-hotplug issue in loongson3_ipi_interrupt()
setup_per_cpu_areas() only setup __per_cpu_offset[] for each possible
cpu, but loongson_sysconf.nr_cpus can be greater than possible cpus
(due to reserved_cpus_mask). So in loongson3_ipi_interrupt(), percpu
access will touch the original varible in .data..percpu section which
has been freed. Without this patch, cpu-hotplug will cause memery
corruption.
Signed-off-by: Huacai Chen <chenhc@lemote.com> Cc: John Crispin <john@phrozen.org> Cc: Steven J. Hill <Steven.Hill@imgtec.com> Cc: linux-mips@linux-mips.org Cc: Fuxin Zhang <zhangfx@lemote.com> Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/10524/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
James Hogan [Thu, 4 Jun 2015 12:25:27 +0000 (13:25 +0100)]
MIPS: Fix enabling of DEBUG_STACKOVERFLOW
Commit 334c86c494b9 ("MIPS: IRQ: Add stackoverflow detection") added
kernel stack overflow detection, however it only enabled it conditional
upon the preprocessor definition DEBUG_STACKOVERFLOW, which is never
actually defined. The Kconfig option is called DEBUG_STACKOVERFLOW,
which manifests to the preprocessor as CONFIG_DEBUG_STACKOVERFLOW, so
switch it to using that definition instead.
The patch e85c9a7abfa4: ("cxgb4/cxgb4vf: Add code to calculate T5 BAR2
Offsets for SGE Queue Registers") from Dec 3, 2014, leads to the
following static checker warning:
drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:5358
t4_bar2_sge_qregs()
warn: should '(qid >> qpp_shift) << page_shift' be a 64 bit type?
This patch fixes it
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 6 Jun 2015 04:26:07 +0000 (21:26 -0700)]
Merge branch 'cxgb4-next'
Hariprasad Shenai says:
====================
Free VI, flush sge ec and some other misc. fixes
This patch series adds the following.
Free VI interface during remove, flush SGE ec routine, rename
t4_link_start to t4_link_l1cfg since it only does l1 configuration, set
mac addr from when we can't contact firmware for debug purpose, set pcie
completion timeout and use fw interface to access TP_PIO_XXX registers
This patch series has been created against net-next tree and includes
patches on cxgb4 driver.
We have included all the maintainers of respective drivers. Kindly review
the change and let us know in case of any review comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb4: Use FW LDST cmd to access TP_PIO_{ADDR, DATA} register first
The TP_PIO_{ADDR,DATA} registers are are in conflict with the firmware's
use of these registers. Added a routine to access it through FW LDST
cmd.
Access all TP_PIO_{ADDR,DATA} register access through new routine if FW
is alive. If firmware is dead, than fall back to indirect access.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
t4_link_start() was completely misnamed. It does _not_ start up the
link. It merely does the L1 Configuration for the link. The Link Up
process is started automatically by the firmware when the number of
enabled Virtual Interfaces on a port goes from 0 to 1. So renaming
this routine to t4_link_l1cfg() for better documentation.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 6 Jun 2015 04:15:50 +0000 (21:15 -0700)]
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-06-04
This series contains updates to i40e and i40evf.
Anjali provides three fixes, first to resolve a Tx queue hang if mixed
size frags are passed to the driver while using TSO. There was a corner
case where we needed to linearize but we were not. Next fixes a bug in
the default configuration which prevented a software bridge loaded on the
PF interface from working correctly because broadcast packets are
incorrectly looped back. Lastly fixes an NPAR bug when SRIOV is enabled,
where we need to be in VEB mode, not VEPA mode at probe.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Chris Leech [Thu, 28 May 2015 19:51:51 +0000 (12:51 -0700)]
iscsi_ibft: filter null v4-mapped v6 addresses
I've had reports of UEFI platforms failing iSCSI boot in various
configurations, that ended up being caused by network initialization
scripts getting tripped up by unexpected null addresses (0.0.0.0) being
reported for gateways, dhcp servers, and dns servers.
The tianocore EDK2 iSCSI driver generates an iBFT table that always uses
IPv4-mapped IPv6 addresses for the NIC structure fields. This results
in values that are "not present or not specified" being reported as
::ffff:0.0.0.0 rather than all zeros as specified.
The iscsi_ibft module filters unspecified fields from the iBFT from
sysfs, preventing userspace from using invalid values and making it easy
to check for the presence of a value. This currently fails in regard to
these mapped null addresses.
In order to remain consistent with how the iBFT information is exposed,
we should accommodate the behavior of the tianocore iSCSI driver as it's
already in the wild in a large number of servers.
Tested under qemu using an OVMF build of tianocore EDK2.
Signed-off-by: Chris Leech <cleech@redhat.com> Reviewed-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The map_single() function is not defined as static, even though it
doesn't seem to be used anywhere else in the kernel. Make it static to
avoid namespace pollution since this is a rather generic symbol.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Russell King [Fri, 5 Jun 2015 22:27:30 +0000 (08:27 +1000)]
drm: fix writing to /sys/class/drm/*/status
Writing to a file is supposed to return the number of bytes written.
Returning zero unfortunately causes bash to constantly spin trying
to write to the sysfs file, to such an extent that even ^c and ^z
have no effect. The only way out of that is to kill the shell and
log back in. This isn't nice behaviour.
Fix it by returning the number of characters written to sysfs files.
[airlied: used suggestion from Al Viro] Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Fri, 5 Jun 2015 21:14:13 +0000 (07:14 +1000)]
Merge tag 'drm-intel-fixes-2015-06-05' of git://anongit.freedesktop.org/drm-intel into drm-fixes
bunch of i915 fixes.
* tag 'drm-intel-fixes-2015-06-05' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Move WaBarrierPerformanceFixDisable:skl to skl code from chv code
drm/i915: Include G4X/VLV/CHV in self refresh status
drm/i915: Initialize HWS page address after GPU reset
drm/i915: Don't skip request retirement if the active list is empty
drm/i915/hsw: Fix workaround for server AUX channel clock divisor
Linus Torvalds [Fri, 5 Jun 2015 17:22:06 +0000 (10:22 -0700)]
Merge tag 'pci-v4.1-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"Resource management
- Fix IOV sorting by alignment (Wei Yang)
- Preserve resource size during alignment reordering (Yinghai Lu)
Miscellaneous
- MAINTAINERS: Add Pratyush for SPEAr13xx and DesignWare PCIe (Pratyush Anand)"
* tag 'pci-v4.1-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Preserve resource size during alignment reordering
PCI: Fix IOV resource sorting by alignment requirement
MAINTAINERS: Add Pratyush Anand as SPEAr13xx and DesignWare PCIe maintainer
Linus Torvalds [Fri, 5 Jun 2015 17:16:52 +0000 (10:16 -0700)]
Merge tag 'sound-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"It was a fairly calm week; here you can find only a few trivial quirks
and fixes for USB and HD-audio. All changes are pretty device
specific"
* tag 'sound-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usb-audio: fix missing input volume controls in MAYA44 USB(+)
ALSA: usb-audio: add MAYA44 USB+ mixer control names
ALSA: hda/realtek - Add a fixup for another Acer Aspire 9420
ALSA: hda - Fix jack detection at resume with VT codecs
ALSA: usb-audio: don't try to get Outlaw RR2150 sample rate
ALSA: usb-audio: Add mic volume fix quirk for Logitech Quickcam Fusion
ALSA: hda/realtek - Suooprt Dell headset mode for ALC256
Linus Torvalds [Fri, 5 Jun 2015 17:14:51 +0000 (10:14 -0700)]
Merge tag 'iommu-fixes-v4.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fix from Joerg Roedel:
"Only one patch:
- Revert "iommu/amd: Don't allocate with __GFP_ZERO in
alloc_coherent".
This patch caused problems with some drivers, so it is better to
revert it now until the drivers have been fixed"
* tag 'iommu-fixes-v4.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
Revert "iommu/amd: Don't allocate with __GFP_ZERO in alloc_coherent"
Linus Torvalds [Fri, 5 Jun 2015 17:03:48 +0000 (10:03 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Misc fixes:
- early_idt_handlers[] fix that fixes the build with bleeding edge
tooling
- build warning fix on GCC 5.1
- vm86 fix plus self-test to make it harder to break it again"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/asm/irq: Stop relying on magic JMP behavior for early_idt_handlers
x86/asm/entry/32, selftests: Add a selftest for kernel entries from VM86 mode
x86/boot: Add CONFIG_PARAVIRT_SPINLOCKS quirk to arch/x86/boot/compressed/misc.h
x86/asm/entry/32: Really make user_mode() work correctly for VM86 mode
Linus Torvalds [Fri, 5 Jun 2015 17:00:53 +0000 (10:00 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"The biggest chunk of the changes are two regression fixes: a HT
workaround fix and an event-group scheduling fix. It's been verified
with 5 days of fuzzer testing.
Linus Torvalds [Fri, 5 Jun 2015 16:58:36 +0000 (09:58 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Just two small fixes: one radeon, one amdkfd"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/amdkfd: fix topology bug with capability attr.
drm/radeon: use proper ACR regisiter for DCE3.2
Linus Torvalds [Fri, 5 Jun 2015 16:54:43 +0000 (09:54 -0700)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c bug fixes from Wolfram Sang:
"Two small bugfixes for I2C"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: s3c2410: fix oops in suspend callback for non-dt platforms
i2c: hix5hd2: Fix modalias to make module auto-loading work
Hans de Goede [Fri, 5 Jun 2015 05:31:43 +0000 (22:31 -0700)]
Input: alps - do not reduce trackpoint speed by half
On some v7 devices (e.g. Lenovo-E550) the deltas reported are typically
only in the 0-1 range dividing this by 2 results in a range of 0-0.
And even for v7 devices where this does not lead to making the trackstick
entirely unusable, it makes it twice as slow as before we added v7 support
and were using the ps/2 mouse emulation of the dual point setup.
If some kind of generic slowdown is actually necessary for some devices,
then that belongs in userspace, not in the kernel.
Cc: stable@vger.kernel.org Reported-and-tested-by: Rico Moorman <rico.moorman@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@gmail.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
i40e: Make sure to be in VEB mode if SRIOV is enabled at probe
If SRIOV is enabled we need to be in VEB mode not VEPA mode at probe.
This fixes an NPAR bug when SRIOV is enabled in the BIOS.
Change-ID: Ibf006abafd9a0ca3698ec24848cd771cf345cbbc Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The patch fixes a bug in the default configuration which
prevented a software bridge loaded on the PF interface from
working correctly because broadcast packets are incorrectly
looped back.
Fix the general case, by loading the driver in VEPA mode Until a
VF or VMDq VSI is added. This way loopback on the Main VSI is
turned off until needed and can resolve the issue of unnecessary
reflection for users that do not have VF or VMDq VSIs setup.
The driver must now coordinate the loopback setting for the Flow
Director (FDIR) VSI to make sure it is in sync with the current
VEB or VEPA mode setting.
The user can still switch bridge modes from the bridge commands and
choose to be in VEPA mode with VF VSIs. Because of hardware
requirements, the call to switch to VEB mode when no VF/VMDqs are
present will be rejected.
NOTE: This patch uses BIT_ULL as that is preferred going forward,
a followup patch in the lower priority queue to net-next will fix
up the remaining 1 << usages.
Change-ID: Ib121ddb18fe4b3c4f52e9deda6fcbeb9105683d1 Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e/i40evf: Fix mixed size frags and linearization
This patch fixes a bug where the i40e Tx queue will hang if this
skb is passed to the driver.
With mixed size fragments while using TSO there was a corner case
where we needed to linearize but we were not. This was seen with
iSCSI traffic and could be reproduced with a frag list that looks
like this:
"IS_ENABLED(PPC_PSERIES)" always evaluates to false, as IS_ENABLED() is
supposed to be used with the full Kconfig symbol name, including the
"CONFIG_" prefix.
Add the missing "CONFIG_" prefix to fix this.
Fixes: a25095d451ece23b ("of: Move dynamic node fixups out of powerpc and into common code") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Cc: stable@vger.kernel.org #+3.17 Signed-off-by: Grant Likely <grant.likely@linaro.org>
David S. Miller [Thu, 4 Jun 2015 23:41:02 +0000 (16:41 -0700)]
Merge branch 'mlx5-next'
Or Gerlitz says:
====================
mlx5: Add Interface Step Sequence ID support
ISSI (Interface Step Sequence ID) defines the step sequence ID of the
interface between the driver to the firmware and is incremented by
steps of one. ISSI is used to enable deprecating/modifying features,
command interfaces and such, while maintaining compatibility.
As the driver serves both ConnectIB (CIB) and ConnectX4, we carefully
made sure that the IB functionality keeps running also on older CIB
firmware releases that don't support ISSI.
The Ethernet functionailty is available only on ConnectX4 where all
firmware releases support the feature since the very basic ISSI level.
So at this point no need for compatility code there.
As done prior to this series, when the Ethernet functionlity is enabled,
during the initialization flow, the core driver performs a query of the
supported ISSIs using the QUERY_ISSI command, and then, if ISSI is supported,
sets the actual issi value informing the firmware on which ISSI level to run,
using SET_ISSI command.
Previously, the IB driver wasn't ready to work on that mode, and hence
building both the IB driver and the Ethernet functionality in the core
driver were disallowed by Kconfigs, with this series, we allow users to
enable them both.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethernet functionality is only available when working in ISSI > 0 mode.
Previously, the IB driver wasn't ready to work on that mode, and hence
building both the IB driver and the Ethernet functionality in the core
driver were disallowed by Kconfigs.
Now, once we have all the pre-steps in place, we can remove this limitation.
The last steps in the IB driver for getting that setup to work are:
create dummy SRQ for the driver's use (until now we could use XRC_SRQ
as SRQ and XRC_SRQ, after moving to ISSI > 0, we separate XRC SRQs from
basic SRQs) and adapt the create QP function to be compatible with ISSI > 0.
Signed-off-by: Haggai Abramovsky <hagaya@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Majd Dibbiny [Thu, 4 Jun 2015 16:30:46 +0000 (19:30 +0300)]
IB/mlx5: Avoid using the MAD_IFC command under ISSI > 0 mode
In ISSI > 0 mode, most of the MAD_IFC command features are deprecated, and can't
be used. Therefore, when in that mode, we replace all of them with other commands
that provide the required functionality.
Signed-off-by: Majd Dibbiny <majd@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Majd Dibbiny [Thu, 4 Jun 2015 16:30:45 +0000 (19:30 +0300)]
net/mlx5_core: Add more query port helpers
Add the following helpers:
1. mlx5_query_port_proto_oper -- queries the port speed port mask
2. mlx5_query_port_link_width_oper - queries the port link with bitmask
3. mlx5_query_port_vl_hw_cap - queries the Virtual Lanes supported on this port
These helpers will be used from the IB driver when working in ISSI > 0 mode.
Signed-off-by: Majd Dibbiny <majd@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Majd Dibbiny [Thu, 4 Jun 2015 16:30:44 +0000 (19:30 +0300)]
net/mlx5_core: Use port number when querying port ptys
Until now, mlx5_query_port_ptys always queried port number one.
Added new argument in the function's prototype so we can also query
the second port. This will be needed when thr helper will be invoked
from the IB driver on non FPP (Function-Per-Port) devices.
Signed-off-by: Majd Dibbiny <majd@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Majd Dibbiny [Thu, 4 Jun 2015 16:30:43 +0000 (19:30 +0300)]
net/mlx5_core: Use port number in the query port mtu helpers
Extend the function prototypes for max and operational mtu to take the
local port number. In the Ethernet driver is this hard coded to one,
since ConnectX4 Ethernet devices are always function-per-port.
The IB driver also serves older devices (ConnectIB) which isn't such,
and hence the part can vary.
Signed-off-by: Majd Dibbiny <majd@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/mlx5_core: Check the return bitmask when querying ISSI
The determination of the supported ISSI versions should be conditioned
on the returned mask, and not only on the return status of the query
ISSI command, fix that.
Signed-off-by: Haggai Abramovsky <hagaya@mellanox.com> Signed-off-by: Majd Dibbiny <majd@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/mlx5_core: Enable XRCs and SRQs when using ISSI > 0
When working in ISSI > 0 mode, the model exposed by the device for
XRCs and SRQs is different. XRCs use XRC SRQs and plain SRQs are based
on RPM (Receive Memory Pool).
Add helper functions to create, modify, query, and arm XRC SRQs and RMPs.
Signed-off-by: Haggai Abramovsky <hagaya@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-bionic-kernel.git / log