Read/write requests to devices without implemented read/write_iter
using fixed buffers can cause general protection fault, which totally
hangs a machine.
io_import_fixed() initialises iov_iter with bvec, but loop_rw_iter()
accesses it as iovec, dereferencing random address.
The SDIO HW reset procedure in mwifiex_sdio_card_reset_work() is broken,
when the SDIO card is shared with another SDIO func driver. This is the
case when the Bluetooth btmrvl driver is being used in combination with
mwifiex. More precisely, when mwifiex_sdio_card_reset_work() runs to resets
the SDIO card, the btmrvl driver doesn't get notified about it. Beyond that
point, the btmrvl driver will fail to communicate with the SDIO card.
This is a generic problem for SDIO func drivers sharing an SDIO card, which
are about to be addressed in subsequent changes to the mmc core and the
mmc_hw_reset() interface. In principle, these changes means the
mmc_hw_reset() interface starts to return 1 if the are multiple drivers for
the SDIO card, as to indicate to the caller that the reset needed to be
scheduled asynchronously through a hotplug mechanism of the SDIO card.
Let's prepare the mwifiex driver to support the upcoming new behaviour of
mmc_hw_reset(), which means extending the mwifiex_sdio_card_reset_work() to
support the asynchronous SDIO HW reset path. This also means, we need to
allow the ->remove() callback to run, without waiting for the FW to be
loaded. Additionally, during system suspend, mwifiex_sdio_suspend() may be
called when a reset has been scheduled, but waiting to be executed. In this
scenario let's simply return -EBUSY to abort the suspend process, as to
allow the reset to be completed first.
Reviewed-by: Douglas Anderson <dianders@chromium.org> Tested-by: Douglas Anderson <dianders@chromium.org> Cc: stable@vger.kernel.org # v5.4+ Acked-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Since the commit 7723f4c5ecdb ("driver core: platform: Add an error message
to platform_get_irq*()") platform_get_irq() started issuing an error message.
Thus, there is no need to have the same in the driver
Fixes: 7723f4c5ecdb ("driver core: platform: Add an error message to platform_get_irq*()") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191023103558.51862-1-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The interrupt clear flag register is a "write 1 to clear" register.
So, only writing ones allows to clear flags:
- Replace buggy stm32_clr_bits() by a simple write to clear error flags
- Replace useless read/modify/write stm32_set_bits() routine by a
simple write to clear TC (transfer complete) flag.
PL011's ->flush_buffer() implementation releases and reacquires the port
lock. Due to a race condition here, data can end up being added to the
circular buffer but neither being discarded nor being sent out. This
leads to, for example, tcdrain(2) waiting indefinitely.
According to the comment in the code, the releasing of the lock around
dmaengine_terminate_all() is to avoid a deadlock with the DMA engine
callback. However, since the time this code was written, the DMA engine
API documentation seems to have been clarified to say that
dmaengine_terminate_all() (in the identically implemented but
differently named dmaengine_terminate_async() variant) does not wait for
any running complete callback to be completed and can even be called
from a complete callback. So there is no possibility of deadlock if the
DMA engine driver implements this API correctly.
So we should be able to just remove this release and reacquire of the
lock to prevent the aforementioned race condition.
hci_qca interfaces to the wcn3990 via a uart_dm on the msm8998 mtp and
Lenovo Miix 630 laptop. As part of initializing the wcn3990, hci_qca
disables flow, configures the uart baudrate, and then reenables flow - at
which point an event is expected to be received over the uart from the
wcn3990. It is observed that this event comes after the baudrate change
but before hci_qca re-enables flow. This is unexpected, and is a result of
msm_reset() being broken.
According to the uart_dm hardware documentation, it is recommended that
automatic hardware flow control be enabled by setting RX_RDY_CTL. Auto
hw flow control will manage RFR based on the configured watermark. When
there is space to receive data, the hw will assert RFR. When the watermark
is hit, the hw will de-assert RFR.
The hardware documentation indicates that RFR can me manually managed via
CR when RX_RDY_CTL is not set. SET_RFR asserts RFR, and RESET_RFR
de-asserts RFR.
msm_reset() is broken because after resetting the hardware, it
unconditionally asserts RFR via SET_RFR. This enables flow regardless of
the current configuration, and would undo a previous flow disable
operation. It should instead de-assert RFR via RESET_RFR to block flow
until the hardware is reconfigured. msm_serial should rely on the client
to specify that flow should be enabled, either via mctrl() or the termios
structure, and only assert RFR in response to those triggers.
Fixes: 04896a77a97b ("msm_serial: serial driver for MSM7K onboard serial peripheral.") Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: stable <stable@vger.kernel.org> Reviewed-by: Andy Gross <agross@kernel.org> Link: https://lore.kernel.org/r/20191021154616.25457-1-jeffrey.l.hugo@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The dmaengine_prep_slave_sg needs to use sg count returned
by dma_map_sg, not use sport->dma_tx_nents, because the return
value of dma_map_sg is not always same with "nents".
When enabling iommu for lpuart + edma, iommu framework may concatenate
two sgs into one.
Fixes: 6250cc30c4c4e ("tty: serial: fsl_lpuart: Use scatter/gather DMA for Tx") Cc: <stable@vger.kernel.org> Signed-off-by: Peng Fan <peng.fan@nxp.com> Link: https://lore.kernel.org/r/1572932977-17866-1-git-send-email-peng.fan@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
As platform_get_irq() now prints an error when the interrupt does not
exist, this warnings are printed on bananapi-r2:
[ 4.935780] mt6577-uart 11004000.serial: IRQ index 1 not found
[ 4.962589] 11002000.serial: ttyS1 at MMIO 0x11002000 (irq = 202, base_baud = 1625000) is a ST16650V2
[ 4.972127] mt6577-uart 11002000.serial: IRQ index 1 not found
[ 4.998927] 11003000.serial: ttyS2 at MMIO 0x11003000 (irq = 203, base_baud = 1625000) is a ST16650V2
[ 5.008474] mt6577-uart 11003000.serial: IRQ index 1 not found
Fix this by calling platform_get_irq_optional() instead.
When building for a non-Cavium MIPS system with COMPILE_TEST=y, the
Octeon ethernet driver hits a number of issues due to use of macros
provided only for CONFIG_CAVIUM_OCTEON_SOC=y configurations. For
example:
drivers/staging/octeon/ethernet-rx.c:190:6: error:
'CONFIG_CAVIUM_OCTEON_CVMSEG_SIZE' undeclared (first use in this function)
drivers/staging/octeon/ethernet-rx.c:472:25: error:
'OCTEON_IRQ_WORKQ0' undeclared (first use in this function)
These come from various asm/ headers that a non-Octeon build will be
using a non-Octeon version of.
Fix this by using the octeon-stubs.h header for non-Cavium MIPS builds,
and only using the real asm/octeon/ headers when building a Cavium
Octeon kernel configuration.
This requires that octeon-stubs.h doesn't redefine XKPHYS_TO_PHYS, which
is defined for MIPS by asm/addrspace.h which is pulled in by many other
common asm/ headers.
Signed-off-by: Paul Burton <paul.burton@mips.com> Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
URL: https://lore.kernel.org/linux-mips/CAMuHMdXvu+BppwzsU9imNWVKea_hoLcRt9N+a29Q-QsjW=ip2g@mail.gmail.com/ Fixes: 171a9bae68c7 ("staging/octeon: Allow test build on !MIPS") Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: David S. Miller <davem@davemloft.net> Link: https://lore.kernel.org/r/20191007231741.2012860-1-paul.burton@mips.com Cc: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Commit 7723f4c5ecdb ("driver core: platform: Add an error message to
platform_get_irq*()") added an error message to avoid drivers having
to print an error message when IRQ lookup fails. However, there are
some cases where IRQs are optional and so new optional versions of
the platform_get_irq*() APIs have been added for these cases.
The IRQs for Tegra HSP module are optional because not all instances
of the module have the doorbell and all of the shared interrupts.
Hence, since the above commit was applied the following error messages
are now seen on Tegra194 ...
ERR KERN tegra-hsp c150000.hsp: IRQ doorbell not found
ERR KERN tegra-hsp c150000.hsp: IRQ shared0 not found
The Tegra HSP driver deliberately does not fail if these are not found
and so fix the above errors by updating the Tegra HSP driver to use
the platform_get_irq_byname_optional() API.
On compat interfaces, the high order bits of nanoseconds should be zeroed
out. This is because the application code or the libc do not guarantee
zeroing of these. If used without zeroing, kernel might be at risk of using
timespec values incorrectly.
Originally it was handled correctly, but lost during is_compat_syscall()
cleanup. Revert the condition back to check CONFIG_64BIT.
On sparc64, the whole physical IO address space is accessible using
physically addressed loads and stores. *_uc does nothing like the
others.
Cc: <stable@vger.kernel.org> # v4.19+ Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Tuowen Zhao <ztuowen@gmail.com> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Commit 4fdbfd60a3a2 ("arm64: tegra: Add PCIe slot supply information
in p2972-0000 platform") added regulators for the PCIe slot on the
Jetson Xavier platform. One of these regulators has an active-low enable
and this commit incorrectly added an active-low specifier for the GPIO
which causes the following warning to occur on boot ...
WARNING KERN regulator@3 GPIO handle specifies active low - ignored
The fixed-regulator binding does not use the active-low flag from the
gpio specifier and purely relies of the presence of the
'enable-active-high' property to determine if it is active high or low
(if this property is omitted). Fix this warning by setting the GPIO
to active-high in the GPIO specifier. Finally, remove the
'enable-active-low' as this is not a valid property.
Fixes: 4fdbfd60a3a2 ("arm64: tegra: Add PCIe slot supply information in p2972-0000 platform") Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Commit 34993594181d ("arm64: tegra: Enable HDMI on Jetson TX1")
added a regulator for HDMI on the Jetson TX1 platform. This regulator
has an active high enable, but the GPIO specifier for enabling the
regulator incorrectly defines it as active-low. This causes the
following warning to occur on boot ...
WARNING KERN regulator@10 GPIO handle specifies active low - ignored
The fixed-regulator binding does not use the active-low flag from the
gpio specifier and purely relies of the presence of the
'enable-active-high' property to determine if it is active high or low
(if this property is omitted). Fix this warning by setting the GPIO
to active-high in the GPIO specifier which aligns with the presense of
the 'enable-active-high' property.
UBUNTU: SAUCE: net: ena: fix too long default tx interrupt moderation interval
BugLink: https://bugs.launchpad.net/bugs/1853180
Current default non-adaptive tx interrupt moderation interval is 196 us.
This commit sets it to 0, which is much more sensible as a default value.
It can be modified using ethtool -C.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Reference: https://lore.kernel.org/netdev/1572868728-5211-1-git-send-email-akiyano@amazon.com/ Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
expected output: rx-usecs 128
actual output: rx-usecs 0
Reason for issue:
In stage 3, ethtool userspace calls first the ena_get_coalesce() handler
to get the current value of all properties, and then the ena_set_coalesce()
handler. When ena_get_coalesce() is called the adaptive interrupt
moderation is still on. There is an if in the code that returns the
rx_coalesce_usecs only if the adaptive interrupt moderation is off.
And since it is still on, rx_coalesce_usecs is not set, meaning it
stays 0.
Solution to issue:
Remove this if static interrupt moderation intervals have nothing to do with
dynamic ones.
expected output: rx-usecs 128
actual output: rx-usecs 0
Reason for issue:
In stage 3, when ena_set_coalesce() is called, the handler tests if
rx adaptive interrupt moderation is on, and if it is, it returns before
getting to the part in the function that sets the rx non-adaptive
interrupt moderation interval.
Solution to issue:
Remove the return from the function when rx adaptive interrupt moderation
is on.
Additional small fixes in this commit:
--------------------------------------
1. Remove 2 unnecessary comments.
2. Remove 4 unnecesary "{}" in single row if statements.
3. Reorder ena_set_coalesce() to make sense.
4. Change the names of ena_update_tx/rx_rings_intr_moderation()
functions to ena_update_tx/rx_rings_nonadaptive_intr_moderation() for
clarity.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Reference: https://lore.kernel.org/netdev/1572868728-5211-1-git-send-email-akiyano@amazon.com/ Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Seth Forshee [Mon, 25 Nov 2019 14:34:00 +0000 (15:34 +0100)]
UBUNTU: [Debian] Fix warnings when checking for modules signatures
BugLink: https://bugs.launchpad.net/bugs/1853843
When detecting module signatures, the current approach causes
this warning for modules lacking a signature:
/bin/bash: line 5: warning: command substitution: ignored null byte in input
My original approach used read, which works well, but for unknown
reasons causes an error from bash when by itself as the first
line in the if clause. Putting it in a no-op while loop prevents
the error, but it has the advantage of working without flooding
the build logs with warnings.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Seth Forshee [Mon, 18 Nov 2019 15:39:00 +0000 (16:39 +0100)]
UBUNTU: [Packaging] Fix module signing with older modinfo
BugLink: https://bugs.launchpad.net/bugs/1852581
Not all versions of modinfo support the signer field;
specifically, the version in boinic does not. This leaves all
modules unsigned in hwe kernels based on eoan and later. Change
the check to look for the magic string at the end of the module,
which does not rely on any external tools being aware of module
signatures.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com> Acked-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Lucas De Marchi [Fri, 29 Nov 2019 06:10:23 +0000 (14:10 +0800)]
drm/i915: fix port checks for MST support on gen >= 11
BugLink: https://bugs.launchpad.net/bugs/1854432
Both Ice Lake and Elkhart Lake (gen 11) support MST on all external
connections except DDI A. Tiger Lake (gen 12) supports on all external
connections.
Move the check to happen inside intel_dp_mst_encoder_init() and add
specific platform checks.
v2: Replace != with == checks for ports on gen < 11 (Ville)
Kailang Yang [Fri, 29 Nov 2019 01:16:25 +0000 (09:16 +0800)]
UBUNTU: SAUCE: ALSA: hda/realtek - Dell headphone has noise on unmute for ALC236
BugLink: https://launchpad.net/bugs/1854401
headphone have noise even the volume is very small.
Let it fill up pcbeep hidden register to default value.
The issue was gone.
Fixes: 4344aec84bd8 ("ALSA: hda/realtek - New codec support for ALC256") Fixes: 736f20a70608 ("ALSA: hda/realtek - Add support for ALC236/ALC3204") Signed-off-by: Kailang Yang <kailang@realtek.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/9ae47f23a64d4e41a9c81e263cd8a250@realtek.com Signed-off-by: Takashi Iwai <tiwai@suse.de>
(cherry picked from commit e1e8c1fdce8b00fce08784d9d738c60ebf598ebc
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound.git) Signed-off-by: Hui Wang <hui.wang@canonical.com> Acked-by: Sultan Alsawaf <sultan.alsawaf@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Just like Ice Lake, Comet Lake can also reuse all the Cannon Lake PCH
IPs. No additional effort is needed to enable but to simply reuse them.
Cc: Mario Limonciello <mario.limonciello@dell.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Srinivas Pandruvada <srinivas.pandruvada@intel.com> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Kan Liang <kan.liang@intel.com> Cc: David E. Box <david.e.box@intel.com> Cc: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com> Cc: Tony Luck <tony.luck@intel.com> Signed-off-by: Gayatri Kammela <gayatri.kammela@intel.com>
(cherry picked from https://lkml.org/lkml/2019/11/18/713) Signed-off-by: You-Sheng Yang <vicamo.yang@canonical.com> Acked-by: Anthony Wong <anthony.wong@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
qize wang [Tue, 26 Nov 2019 08:39:14 +0000 (09:39 +0100)]
UBUNTU: SAUCE: mwifiex: Fix heap overflow in mmwifiex_process_tdls_action_frame()
mwifiex_process_tdls_action_frame() without checking
the incoming tdls infomation element's vality before use it,
this may cause multi heap buffer overflows.
Fix them by putting vality check before use it.
Signed-off-by: qize wang <wangqize888888888@gmail.com>
CVE-2019-14901
(cherry picked from https://patchwork.kernel.org/patch/11257535/) Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Acked-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Wen Huang [Tue, 26 Nov 2019 08:39:13 +0000 (09:39 +0100)]
UBUNTU: SAUCE: libertas: Fix two buffer overflows at parsing bss descriptor
add_ie_rates() copys rates without checking the length
in bss descriptor from remote AP.when victim connects to
remote attacker, this may trigger buffer overflow.
lbs_ibss_join_existing() copys rates without checking the length
in bss descriptor from remote IBSS node.when victim connects to
remote attacker, this may trigger buffer overflow.
Fix them by putting the length check before performing copy.
This fix addresses CVE-2019-14896 and CVE-2019-14897.
Wen Huang [Tue, 26 Nov 2019 08:39:12 +0000 (09:39 +0100)]
UBUNTU: SAUCE: mwifiex: fix possible heap overflow in mwifiex_process_country_ie()
mwifiex_process_country_ie() function parse elements of bss
descriptor in beacon packet. When processing WLAN_EID_COUNTRY
element, there is no upper limit check for country_ie_len before
calling memcpy. The destination buffer domain_info->triplet is an
array of length MWIFIEX_MAX_TRIPLET_802_11D(83). The remote
attacker can build a fake AP with the same ssid as real AP, and
send malicous beacon packet with long WLAN_EID_COUNTRY elemen
(country_ie_len > 83). Attacker can force STA connect to fake AP
on a different channel. When the victim STA connects to fake AP,
will trigger the heap buffer overflow. Fix this by checking for
length and if found invalid, don not connect to the AP.
Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
(cherry picked from commit f84fdcbc8ec02ea34bbc641359c2a69d0d1242d4 linux-next) Signed-off-by: You-Sheng Yang <vicamo.yang@canonical.com> Acked-by: Anthony Wong <anthony.wong@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
(cherry picked from commit cae478114fbe2e6f4cb9194360cf0789a923be13 linux-next) Signed-off-by: You-Sheng Yang <vicamo.yang@canonical.com> Acked-by: Anthony Wong <anthony.wong@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Hui Wang [Mon, 25 Nov 2019 03:19:01 +0000 (11:19 +0800)]
UBUNTU: SAUCE: ALSA: hda/realtek - Move some alc236 pintbls to fallback table
BugLink: https://launchpad.net/bugs/1853791
We have a new Dell machine which needs to apply the quirk
ALC255_FIXUP_DELL1_MIC_NO_PRESENCE, try to use the fallback table
to fix it this time. And we could remove all pintbls of alc236
for applying DELL1_MIC_NO_PRESENCE on Dell machines.
Signed-off-by: Hui Wang <hui.wang@canonical.com> Link: https://lore.kernel.org/r/20191121022644.8078-2-hui.wang@canonical.com Signed-off-by: Takashi Iwai <tiwai@suse.de>
(cherry picked from commit d64ebdbfd4f71406f58210f5ccb16977b4cd31d2
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound.git) Signed-off-by: Hui Wang <hui.wang@canonical.com> Acked-by: Anthony Wong <anthony.wong@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Hui Wang [Mon, 25 Nov 2019 03:19:00 +0000 (11:19 +0800)]
UBUNTU: SAUCE: ALSA: hda/realtek - Move some alc256 pintbls to fallback table
BugLink: https://launchpad.net/bugs/1853791
We have a new Dell machine which needs to apply the quirk
ALC255_FIXUP_DELL1_MIC_NO_PRESENCE, try to use the fallback table
to fix it this time. And we could remove all pintbls of alc256
for applying DELL1_MIC_NO_PRESENCE on Dell machines.
Signed-off-by: Hui Wang <hui.wang@canonical.com> Link: https://lore.kernel.org/r/20191121022644.8078-1-hui.wang@canonical.com Signed-off-by: Takashi Iwai <tiwai@suse.de>
(cherry picked from commit aed8c7f40882015aad45088256231babcbc24482
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound.git) Signed-off-by: Hui Wang <hui.wang@canonical.com> Acked-by: Anthony Wong <anthony.wong@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Amir Goldstein [Fri, 22 Nov 2019 12:16:59 +0000 (12:16 +0000)]
UBUNTU: SAUCE: ovl: fix lookup failure on multi lower squashfs
BugLink: https://bugs.launchpad.net/bugs/1824407
In the past, overlayfs required that lower fs have non null uuid in
order to support nfs export and decode copy up origin file handles.
Commit 9df085f3c9a2 ("ovl: relax requirement for non null uuid of
lower fs") relaxed this requirement for nfs export support, as long
as uuid (even if null) is unique among all lower fs.
However, said commit unintentionally also relaxed the non null uuid
requirement for decoding copy up origin file handles, regardless of
the unique uuid requirement.
Amend this mistake by disabling decoding of copy up origin file handle
from lower fs with a conflicting uuid.
We still encode copy up origin file handles from those fs, because
file handles like those already exist in the wild and because they
might provide useful information in the future.
There is an unhandled corner case described by Miklos this way:
- two filesystems, A and B, both have null uuid
- upper layer is on A
- lower layer 1 is also on A
- lower layer 2 is on B
In this case bad_uuid won't be set for B, because the check only
involves the list of lower fs. Hence we'll try to decode a layer 2
origin on layer 1 and fail.
We will deal with this corner case later.
Reported-by: Colin Ian King <colin.king@canonical.com> Tested-by: Colin Ian King <colin.king@canonical.com> Link: https://lore.kernel.org/lkml/20191106234301.283006-1-colin.king@canonical.com/ Fixes: 9df085f3c9a2 ("ovl: relax requirement for non null uuid ...") Cc: stable@vger.kernel.org # v4.20+ Signed-off-by: Amir Goldstein <amir73il@gmail.com>
(cherry picked from commit b2d4f0ea5af42e16e154254de99da064f3ac551a
https://github.com/amir73il/linux) Acked-by: Andrea Righi <andrea.righi@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1846539
Some distros select all options blindly, which leads to confusion and
bug reports. SOF does not fully support Broadwell due to firmware
dependencies, the machine drivers can only support one option, and
UCM/topology files are still being propagated to downstream distros,
so make SOF on Broadwell an opt-in option that first require distros
to opt-out of existing defaults.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=204237 Fixes: f35bf70f61d3 ('ASoC: Intel: Make sure BDW based machine drivers build for SOF') Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20191101173045.27099-3-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
(cherry picked from commit a6955fe0e2309feeab5ec71e4b0dcbe498f4f497
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound.git) Signed-off-by: Hui Wang <hui.wang@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
[ saf: update configs and annotations, add snd-sof-intel-bdw to
modules.ignore ] Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
When deleting VMs with VFs created by i40e, a general protection
fault occurs in i40e_config_vf_promiscuous_mode due to race
condition for vsi->mac_filter_hash
And it also happens when deleteing pod with VFs
This issue was reported in e1000-devel mailling list
https://sourceforge.net/p/e1000/mailman/message/36766306/
Suggested-by: Billy McFall <bmcfall@redhat.com> Signed-off-by: Gerald Yang <gerald.yang@canonical.com> Acked-by: Sultan Alsawaf <sultan.alsawaf@canonical.com> Acked-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Aurelien Jarno [Tue, 3 Dec 2019 17:09:34 +0000 (14:09 -0300)]
libbpf: Fix readelf output parsing on powerpc with recent binutils
BugLink: https://bugs.launchpad.net/bugs/1854974
On powerpc with recent versions of binutils, readelf outputs an extra
field when dumping the symbols of an object file. For example:
35: 0000000000000838 96 FUNC LOCAL DEFAULT [<localentry>: 8] 1 btf_is_struct
The extra "[<localentry>: 8]" prevents the GLOBAL_SYM_COUNT variable to
be computed correctly and causes the check_abi target to fail.
Fix that by looking for the symbol name in the last field instead of the
8th one. This way it should also cope with future extra fields.
Mika Westerberg [Tue, 26 Nov 2019 08:51:50 +0000 (16:51 +0800)]
PCI/PM: Add missing link delays required by the PCIe spec
BugLink: https://bugs.launchpad.net/bugs/1853991
Currently Linux does not follow PCIe spec regarding the required delays
after reset. A concrete example is a Thunderbolt add-in-card that consists
of a PCIe switch and two PCIe endpoints:
+-1b.0-[01-6b]----00.0-[02-6b]--+-00.0-[03]----00.0 TBT controller
+-01.0-[04-36]-- DS hotplug port
+-02.0-[37]----00.0 xHCI controller
\-04.0-[38-6b]-- DS hotplug port
The root port (1b.0) and the PCIe switch downstream ports are all PCIe Gen3
so they support 8GT/s link speeds.
We wait for the PCIe hierarchy to enter D3cold (runtime):
pcieport 0000:00:1b.0: power state changed by ACPI to D3cold
When it wakes up from D3cold, according to the PCIe 5.0 section 5.8 the
PCIe switch is put to reset and its power is re-applied. This means that we
must follow the rules in PCIe 5.0 section 6.6.1.
For the PCIe Gen3 ports we are dealing with here, the following applies:
With a Downstream Port that supports Link speeds greater than 5.0 GT/s,
software must wait a minimum of 100 ms after Link training completes
before sending a Configuration Request to the device immediately below
that Port. Software can determine when Link training completes by polling
the Data Link Layer Link Active bit or by setting up an associated
interrupt (see Section 6.7.3.3).
Translating this into the above topology we would need to do this (DLLLA
stands for Data Link Layer Link Active):
0000:00:1b.0: wait for 100 ms after DLLLA is set before access to 0000:01:00.0
0000:02:00.0: wait for 100 ms after DLLLA is set before access to 0000:03:00.0
0000:02:02.0: wait for 100 ms after DLLLA is set before access to 0000:37:00.0
I've instrumented the kernel with some additional logging so we can see the
actual delays performed:
pcieport 0000:00:1b.0: power state changed by ACPI to D0
pcieport 0000:00:1b.0: waiting for D3cold delay of 100 ms
pcieport 0000:00:1b.0: waiting for D3hot delay of 10 ms
pcieport 0000:02:01.0: waiting for D3hot delay of 10 ms
pcieport 0000:02:04.0: waiting for D3hot delay of 10 ms
For the switch upstream port (01:00.0 reachable through 00:1b.0 root port)
we wait for 100 ms but not taking into account the DLLLA requirement. We
then wait 10 ms for D3hot -> D0 transition of the root port and the two
downstream hotplug ports. This means that we deviate from what the spec
requires.
Performing the same check for system sleep (s2idle) transitions it turns
out to be even worse. None of the mandatory delays are performed. If this
would be S3 instead of s2idle then according to PCI FW spec 3.2 section
4.6.8. there is a specific _DSM that allows the OS to skip the delays but
this platform does not provide the _DSM and does not go to S3 anyway so no
firmware is involved that could already handle these delays.
On this particular platform these delays are not actually needed because
there is an additional delay as part of the ACPI power resource that is
used to turn on power to the hierarchy but since that additional delay is
not required by any of standards (PCIe, ACPI) it is not present in the
Intel Ice Lake, for example where missing the mandatory delays causes
pciehp to start tearing down the stack too early (links are not yet
trained). Below is an example how it looks like when this happens:
pcieport 0000:83:04.0: pciehp: Slot(4): Card not present
pcieport 0000:87:04.0: PME# disabled
pcieport 0000:83:04.0: pciehp: pciehp_unconfigure_device: domain:bus:dev = 0000:86:00
pcieport 0000:86:00.0: Refused to change power state, currently in D3
pcieport 0000:86:00.0: restoring config space at offset 0x3c (was 0xffffffff, writing 0x201ff)
pcieport 0000:86:00.0: restoring config space at offset 0x38 (was 0xffffffff, writing 0x0)
...
There is also one reported case (see the bugzilla link below) where the
missing delay causes xHCI on a Titan Ridge controller fail to runtime
resume when USB-C dock is plugged. This does not involve pciehp but instead
the PCI core fails to runtime resume the xHCI device:
pcieport 0000:04:02.0: restoring config space at offset 0xc (was 0x10000, writing 0x10020)
pcieport 0000:04:02.0: restoring config space at offset 0x4 (was 0x100000, writing 0x100406)
xhci_hcd 0000:39:00.0: Refused to change power state, currently in D3
xhci_hcd 0000:39:00.0: restoring config space at offset 0x3c (was 0xffffffff, writing 0x1ff)
xhci_hcd 0000:39:00.0: restoring config space at offset 0x38 (was 0xffffffff, writing 0x0)
...
Add a new function pci_bridge_wait_for_secondary_bus() that is called on
PCI core resume and runtime resume paths accordingly if the bridge entered
D3cold (and thus went through reset).
This is second attempt to add the missing delays. The previous solution in c2bf1fc212f7 ("PCI: Add missing link delays required by the PCIe spec") was
reverted because of two issues it caused:
1. One system become unresponsive after S3 resume due to PME service
spinning in pcie_pme_work_fn(). The root port in question reports that
the xHCI sent PME but the xHCI device itself does not have PME status
set. The PME status bit is never cleared in the root port resulting
the indefinite loop in pcie_pme_work_fn().
2. Slows down resume if the root/downstream port does not support Data
Link Layer Active Reporting because pcie_wait_for_link_delay() waits
1100 ms in that case.
This version should avoid the above issues because we restrict the delay to
happen only if the port went into D3cold.
Mika Westerberg [Tue, 26 Nov 2019 08:51:49 +0000 (16:51 +0800)]
PCI/PM: Add pcie_wait_for_link_delay()
BugLink: https://bugs.launchpad.net/bugs/1853991
Add pcie_wait_for_link_delay(). Similar to pcie_wait_for_link() but allows
passing custom activation delay in milliseconds.
Flickerfree boot doesn't work with Eoan and Focal kernels - the flicker
occurs seemingly during kernel startup following this pattern:
1. BIOS logo on a black background
2. Display mode resets, no image on a black background briefly
3. BIOS logo on a black background
According to upstream, the required kernel option to achieve it (coupled
with the quiet cmdline) is FRAMEBUFFER_CONSOLE_DEFERRED_TAKEOVER.
Fix:
Apply the config change, recompile and reboot - a test kernel was
provided and the reporter of this bug said "it doesn't completely
solve the issue, but it's a step in the right direction, so please
enable it".
Regression potential:
Low, config change for an option that is upstream.
Proposing for Focal.
Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
[ saf: update annotations ] Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Andy Shevchenko [Thu, 14 Nov 2019 15:11:47 +0000 (23:11 +0800)]
mfd: intel-lpss: Add Intel Comet Lake PCH-H PCI IDs
BugLink: https://bugs.launchpad.net/bugs/1846335
Intel Comet Lake PCH-H has the same LPSS than Intel Cannon Lake.
Add the new IDs to the list of supported devices.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
(cherry picked from commit dd047dce3a6f5233b98e792e2287cc549da35879 linux-next) Signed-off-by: You-Sheng Yang <vicamo@gmail.com> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Mika Westerberg [Thu, 14 Nov 2019 15:11:46 +0000 (23:11 +0800)]
mtd: spi-nor: intel-spi: Add support for Intel Comet Lake-H SPI serial flash
BugLink: https://bugs.launchpad.net/bugs/1846335
Intel Comet Lake-H PCH has the same SPI serial flash controller as Comet
Lake-LP. Add Comet Lake-H PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
(cherry picked from commit 5a0feb6287e37018af4cbd7754786522ae712980 linux-next) Signed-off-by: You-Sheng Yang <vicamo@gmail.com> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
If we pass 0 as bios_args.datasize argument then (Local5 * 0x08)
is 0 which results in these errors:
[ 71.973305] ACPI BIOS Error (bug): Attempt to CreateField of length zero (20190816/dsopcode-133)
[ 71.973332] ACPI Error: Aborting method \HWMC due to previous error (AE_AML_OPERAND_VALUE) (20190816/psparse-529)
[ 71.973413] ACPI Error: Aborting method \_SB.WMID.WMAA due to previous error (AE_AML_OPERAND_VALUE) (20190816/psparse-529)
And in our HPWMI_WIRELESS2_QUERY calls always failing. for read commands
like HPWMI_WIRELESS2_QUERY the DSZI value is not used / checked, except for
read commands where extra input is needed to specify exactly what to read.
So for HPWMI_WIRELESS2_QUERY we can safely pass the size of the expected
output as insize to hp_wmi_perform_query(), as we are already doing for all
other HPWMI_READ commands we send. Doing so fixes these errors.
The HP WMI calls may take up to 128 bytes of data as input, and
the AML methods implementing the WMI calls, declare a couple of fields for
accessing input in different sizes, specifycally the HWMC method contains:
CreateField (Arg1, 0x80, 0x0400, D128)
Even though we do not use any of the WMI command-types which need a buffer
of this size, the APCI interpreter still tries to create it as it is
declared in generoc code at the top of the HWMC method which runs before
the code looks at which command-type is requested.
This results in many of these errors on many different HP laptop models:
Upstream commit 58e75155009c ("HID: core: move Usage Page concatenation
to Main item") adds support for Usage Page item after Usage ID items
(such as keyboards manufactured by Primax).
Usage Page concatenation in Main item works well for following report
descriptor patterns:
With Usage Page concatenation in Main item, parser recognizes all the
11 Usages as consumer keys, it is not the HID device's real intention.
This patch checks whether Usage Page is really defined after Usage ID
items by comparing usage page using status.
Usage Page concatenation on currently defined Usage Page will always
do in local parsing when Usage ID items encountered.
When Main item is parsing, concatenation will do again with last
defined Usage Page if this page has not been used in the previous
usages concatenation.
Signed-off-by: Candle Sun <candle.sun@unisoc.com> Signed-off-by: Nianfu Bai <nianfu.bai@unisoc.com> Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Cc: Siarhei Vishniakou <svv@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
This reverts commit f2538f999345405f7d2e1194c0c8efa4e11f7b3a. The patch
stopped JFFS2 from being able to mount an existing filesystem with the
following errors:
jffs2: error: (77) jffs2_build_inode_fragtree: Add node to tree failed -22
jffs2: error: (77) jffs2_do_read_inode_internal: Failed to build final fragtree for inode #5377: error -22
Fixes: f2538f999345 ("jffs2: Fix possible null-pointer dereferences...") Cc: stable@vger.kernel.org Suggested-by: Hou Tao <houtao1@huawei.com> Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
It's possible to specify a non-zero s_want_extra_isize via debugging
option, and this can cause bad things(tm) to happen when using a file
system with an inode size of 128 bytes.
Add better checking when the file system is mounted, as well as when
we are actually doing the trying to do the inode expansion.
It was reported [0] that network doesn't wake up on cable plug-in with
certain chip versions. Reason is that on these chip versions the PHY
doesn't detect cable plug-in when being in power-down mode. So prevent
the PHY from powering down if WoL is enabled.
Alan reported [0] that network is broken since the referenced commit
when using jumbo frames. This commit isn't wrong, it just revealed
another issue that has been existing before. According to the vendor
driver the RTL8168e-specific jumbo config doesn't apply for RTL8168evl.
[0] https://lkml.org/lkml/2019/11/30/119
Fixes: 4ebcb113edcc ("r8169: fix jumbo packet handling on resume from suspend") Reported-by: Alan J. Wylie <alan@wylie.me.uk> Tested-by: Alan J. Wylie <alan@wylie.me.uk> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Some versions of iproute2 will output more than one line per entry, which
will cause the test to fail, like:
TEST: ipv6: list and flush cached exceptions [FAIL]
can't list cached exceptions
That happens, for example, with iproute2 4.15.0. When using the -oneline
option, this will work just fine:
TEST: ipv6: list and flush cached exceptions [ OK ]
This also works just fine with a more recent version of iproute2, like
5.4.0.
For some reason, two lines are printed for the IPv4 test no matter what
version of iproute2 is used. Use the same -oneline parameter there instead
of counting the lines twice.
Fixes: b964641e9925 ("selftests: pmtu: Make list_flush_ipv6_exception test more demanding") Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Acked-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
In commit 4f07b80c9733 ("tipc: check msg->req data len in
tipc_nl_compat_bearer_disable") the same patch code was copied into
routines: tipc_nl_compat_bearer_disable(),
tipc_nl_compat_link_stat_dump() and tipc_nl_compat_link_reset_stats().
The two link routine occurrences should have been modified to check
the maximum link name length and not bearer name length.
Fixes: 4f07b80c9733 ("tipc: check msg->reg data len in tipc_nl_compat_bearer_disable") Signed-off-by: John Rutherford <john.rutherford@dektech.com.au> Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
perror(str) is basically equivalent to
print("%s: %s\n", str, strerror(errno)).
New line or colon at the end of str is
a mistake/breaks formatting.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
test_sockmap creates a temporary file to use for sendpage.
this may fail for various reasons. Handle the error rather
than segfault.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Partially sent record cleanup path increments an SG entry
directly instead of using sg_next(). This should not be a
problem today, as encrypted messages should be always
allocated as arrays. But given this is a cleanup path it's
easy to miss was this ever to change. Use sg_next(), and
simplify the code.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Looks like when BPF support was added by commit d3b18ad31f93
("tls: add bpf support to sk_msg handling") and
commit d829e9c4112b ("tls: convert to generic sk_msg interface")
it broke/removed the support for in-place crypto as added by
commit 4e6d47206c32 ("tls: Add support for inplace records
encryption").
The inplace_crypto member of struct tls_rec is dead, inited
to zero, and sometimes set to zero again. It used to be
set to 1 when record was allocated, but the skmsg code doesn't
seem to have been written with the idea of in-place crypto
in mind.
Since non trivial effort is required to bring the feature back
and we don't really have the HW to measure the benefit just
remove the left over support for now to avoid confusing readers.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Add a sendmsg test with very fragmented messages. This should
fill up sk_msg and test the boundary conditions.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
TLS 1.3 started using the entry at the end of the SG array
for chaining-in the single byte content type entry. This mostly
works:
[ E E E E E E . . ]
^ ^
start end
E < content type
/
[ E E E E E E C . ]
^ ^
start end
(Where E denotes a populated SG entry; C denotes a chaining entry.)
If the array is full, however, the end will point to the start:
[ E E E E E E E E ]
^
start
end
And we end up overwriting the start:
E < content type
/
[ C E E E E E E E ]
^
start
end
The sg array is supposed to be a circular buffer with start and
end markers pointing anywhere. In case where start > end
(i.e. the circular buffer has "wrapped") there is an extra entry
reserved at the end to chain the two halves together.
[ E E E E E E . . l ]
(Where l is the reserved entry for "looping" back to front.
As suggested by John, let's reserve another entry for chaining
SG entries after the main circular buffer. Note that this entry
has to be pointed to by the end entry so its position is not fixed.
Examples of full messages:
[ E E E E E E E E . l ]
^ ^
start end
<---------------.
[ E E . E E E E E E l ]
^ ^
end start
Now the end will always point to an unused entry, so TLS 1.3
can always use it.
Fixes: 130b392c6cd6 ("net: tls: Add tls 1.3 support") Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
When tls_do_encryption() fails the SG lists are left with the
SG_END and SG_CHAIN marks in place. One could hope that once
encryption fails we will never see the record again, but that
is in fact not true. Commit d3b18ad31f93 ("tls: add bpf support
to sk_msg handling") added special handling to ENOMEM and ENOSPC
errors which mean we may see the same record re-submitted.
As suggested by John free the record, the BPF code is already
doing just that.
Reported-by: syzbot+df0d4ec12332661dd1f9@syzkaller.appspotmail.com Fixes: d3b18ad31f93 ("tls: add bpf support to sk_msg handling") Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Acked-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
bpf_exec_tx_verdict() may free the record if tls_push_record()
fails, or if the entire record got consumed by BPF. Re-check
ctx->open_rec before touching the data.
Fixes: d3b18ad31f93 ("tls: add bpf support to sk_msg handling") Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Acked-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
If we can't build the flow del notification, we can simply delete
the flow, no need to crash the kernel. Still keep a WARN_ON to
preserve debuggability.
Note: the BUG_ON() predates the Fixes tag, but this change
can be applied only after the mentioned commit.
v1 -> v2:
- do not leak an skb on error
Fixes: aed067783e50 ("openvswitch: Minimize ovs_flow_cmd_del critical section.") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
All the callers of ovs_flow_cmd_build_info() already deal with
error return code correctly, so we can handle the error condition
in a more gracefull way. Still dump a warning to preserve
debuggability.
v1 -> v2:
- clarify the commit message
- clean the skb and report the error (DaveM)
Fixes: ccb1352e76cf ("net: Add Open vSwitch kernel components.") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
This patch is to fix a data-race reported by syzbot:
BUG: KCSAN: data-race in sctp_assoc_migrate / sctp_hash_obj
write to 0xffff8880b67c0020 of 8 bytes by task 18908 on cpu 1:
sctp_assoc_migrate+0x1a6/0x290 net/sctp/associola.c:1091
sctp_sock_migrate+0x8aa/0x9b0 net/sctp/socket.c:9465
sctp_accept+0x3c8/0x470 net/sctp/socket.c:4916
inet_accept+0x7f/0x360 net/ipv4/af_inet.c:734
__sys_accept4+0x224/0x430 net/socket.c:1754
__do_sys_accept net/socket.c:1795 [inline]
__se_sys_accept net/socket.c:1792 [inline]
__x64_sys_accept+0x4e/0x60 net/socket.c:1792
do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x44/0xa9
read to 0xffff8880b67c0020 of 8 bytes by task 12003 on cpu 0:
sctp_hash_obj+0x4f/0x2d0 net/sctp/input.c:894
rht_key_get_hash include/linux/rhashtable.h:133 [inline]
rht_key_hashfn include/linux/rhashtable.h:159 [inline]
rht_head_hashfn include/linux/rhashtable.h:174 [inline]
head_hashfn lib/rhashtable.c:41 [inline]
rhashtable_rehash_one lib/rhashtable.c:245 [inline]
rhashtable_rehash_chain lib/rhashtable.c:276 [inline]
rhashtable_rehash_table lib/rhashtable.c:316 [inline]
rht_deferred_worker+0x468/0xab0 lib/rhashtable.c:420
process_one_work+0x3d4/0x890 kernel/workqueue.c:2269
worker_thread+0xa0/0x800 kernel/workqueue.c:2415
kthread+0x1d4/0x200 drivers/block/aoe/aoecmd.c:1253
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:352
It was caused by rhashtable access asoc->base.sk when sctp_assoc_migrate
is changing its value. However, what rhashtable wants is netns from asoc
base.sk, and for an asoc, its netns won't change once set. So we can
simply fix it by caching netns since created.
Fixes: d6c0256a60e6 ("sctp: add the rhashtable apis for sctp global transport hashtable") Reported-by: syzbot+e3b35fe7918ff0ee474e@syzkaller.appspotmail.com Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Slip_open doesn't clean-up device which registration failed from the
slip_devs device list. On next open after failure this list is iterated
and freed device is accessed. Fix this by calling sl_free_netdev in error
path.
In the implementation of sctp_sf_do_5_2_4_dupcook() the allocated
new_asoc is leaked if security_sctp_assoc_request() fails. Release it
via sctp_association_free().
When user-space sets the OVS_UFID_F_OMIT_* flags, and the relevant
flow has no UFID, we can exceed the computed size, as
ovs_nla_put_identifier() will always dump an OVS_FLOW_ATTR_KEY
attribute.
Take the above in account when computing the flow command message
size.
Fixes: 74ed7ab9264c ("openvswitch: Add support for unique flow IDs.") Reported-by: Qi Jun Ding <qding@redhat.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
When a classful qdisc's child qdisc has set the flag
TCQ_F_CPUSTATS (pfifo_fast for example), the child qdisc's
cpu_bstats should be passed to gnet_stats_copy_basic(),
but many classful qdisc didn't do that. As a result,
`tc -s class show dev DEV` always return 0 for bytes and
packets in this case.
Pass the child qdisc's cpu_bstats to gnet_stats_copy_basic()
to fix this issue.
The qstats also has this problem, but it has been fixed
in 5dd431b6b9 ("net: sched: introduce and use qstats read...")
and bstats still remains buggy.
Fixes: 22e0f8b9322c ("net: sched: make bstats per cpu and estimator RCU safe") Signed-off-by: Dust Li <dust.li@linux.alibaba.com> Signed-off-by: Tony Lu <tonylu@linux.alibaba.com> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
We need to calculate the skb size correctly otherwise we risk triggering
skb_over_panic[1]. The issue is that data_len is added to the skb in a
nl attribute, but we don't account for its header size (nlattr 4 bytes)
and alignment. We account for it when calculating the total size in
the > PSAMPLE_MAX_PACKET_SIZE comparison correctly, but not when
allocating after that. The fix is simple - use nla_total_size() for
data_len when allocating.
To reproduce:
$ tc qdisc add dev eth1 clsact
$ tc filter add dev eth1 egress matchall action sample rate 1 group 1 trunc 129
$ mausezahn eth1 -b bcast -a rand -c 1 -p 129
< skb_over_panic BUG(), tail is 4 bytes past skb->end >
This function was using configuration of port 0 in devicetree for all ports.
In case CPU port was not 0, the delay settings was ignored. This resulted not
working communication between CPU and the switch.
Fixes: f5b8631c293b ("net: dsa: sja1105: Error out if RGMII delays are requested in DT") Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Geert Uytterhoeven reported that using devm_reset_controller_get leads
to a WARNING when probing a reset-controlled PHY. This is because the
device devm_reset_controller_get gets supplied is not actually the
one being probed.
Acquire an unmanaged reset-control as well as free the reset_control on
unregister to fix this.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org> CC: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David Bauer <mail@david-bauer.net> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
While enqueueing a broadcast skb to port->bc_queue, schedule_work()
is called to add port->bc_work, which processes the skbs in
bc_queue, to "events" work queue. If port->bc_queue is full, the
skb will be discarded and schedule_work(&port->bc_work) won't be
called. However, if port->bc_queue is full and port->bc_work is not
running or pending, port->bc_queue will keep full and schedule_work()
won't be called any more, and all broadcast skbs to macvlan will be
discarded. This case can happen:
macvlan_process_broadcast() is the pending function of port->bc_work,
it moves all the skbs in port->bc_queue to the queue "list", and
processes the skbs in "list". During this, new skbs will keep being
added to port->bc_queue in macvlan_broadcast_enqueue(), and
port->bc_queue may already full when macvlan_process_broadcast()
return. This may happen, especially when there are a lot of real-time
threads and the process is preempted.
Fix this by calling schedule_work(&port->bc_work) even if
port->bc_work is full in macvlan_broadcast_enqueue().
Fixes: 412ca1550cbe ("macvlan: Move broadcasts into a work queue") Signed-off-by: Menglong Dong <dong.menglong@zte.com.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
In gve_alloc_queue_page_list(), when a page allocation fails,
qpl->num_entries will be wrong. In this case priv->num_registered_pages
can underflow in gve_free_queue_page_list(), causing subsequent calls
to gve_alloc_queue_page_list() to fail.
Fixes: f5cedc84a30d ("gve: Add transmit and receive support") Signed-off-by: Jeroen de Borst <jeroendb@google.com> Reviewed-by: Catherine Sullivan <csully@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The state/owner of the FPU is saved to fpu_fpregs_owner_ctx by pointing
to the context that is currently loaded. It never changed during the
lifetime of a task - it remained stable/constant.
After deferred FPU registers loading until return to userland was
implemented, the content of fpu_fpregs_owner_ctx may change during
preemption and must not be cached.
This went unnoticed for some time and was now noticed, in particular
since gcc 9 is caching that load in copy_fpstate_to_sigframe() and
reusing it in the retry loop:
copy_fpstate_to_sigframe()
load fpu_fpregs_owner_ctx and save on stack
fpregs_lock()
copy_fpregs_to_sigframe() /* failed */
fpregs_unlock()
*** PREEMPTION, another uses FPU, changes fpu_fpregs_owner_ctx ***
fault_in_pages_writeable() /* succeed, retry */
fpregs_lock()
__fpregs_load_activate()
fpregs_state_valid() /* uses fpu_fpregs_owner_ctx from stack */
copy_fpregs_to_sigframe() /* succeeds, random FPU content */
This is a comparison of the assembly produced by gcc 9, without vs with this
patch:
Use this_cpu_read() instead this_cpu_read_stable() to avoid caching of
fpu_fpregs_owner_ctx during preemption points.
The Fixes: tag points to the commit where deferred FPU loading was
added. Since this commit, the compiler is no longer allowed to move the
load of fpu_fpregs_owner_ctx somewhere else / outside of the locked
section. A task preemption will change its value and stale content will
be observed.
[ bp: Massage. ]
Debugged-by: Austin Clements <austin@google.com> Debugged-by: David Chase <drchase@golang.org> Debugged-by: Ian Lance Taylor <ian@airs.com> Fixes: 5f409e20b7945 ("x86/fpu: Defer FPU state load until return to userspace") Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Rik van Riel <riel@surriel.com> Tested-by: Borislav Petkov <bp@suse.de> Cc: Aubrey Li <aubrey.li@intel.com> Cc: Austin Clements <austin@google.com> Cc: Barret Rhoden <brho@google.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: David Chase <drchase@golang.org> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: ian@airs.com Cc: Ingo Molnar <mingo@redhat.com> Cc: Josh Bleecher Snyder <josharian@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: x86-ml <x86@kernel.org> Link: https://lkml.kernel.org/r/20191128085306.hxfa2o3knqtu4wfn@linutronix.de Link: https://bugzilla.kernel.org/show_bug.cgi?id=205663 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
On zang's Dell XPS 13 9370 after Thunderbolt NVM firmware upgrade the
Thunderbolt controller did not come back as expected. Only after the
system was rebooted it became available again. It is not entirely clear
what happened but I suspect the new NVM firmware image authentication
failed for some reason. Regardless of this the router needs to be power
cycled if NVM authentication fails in order to get it fully functional
again.
This modifies the driver to issue a power cycle in case the NVM
authentication fails immediately when dma_port_flash_update_auth()
returns. We also need to call tb_switch_set_uuid() earlier to be able to
fetch possible NVM authentication failure when DMA port is added.
Add parent device name to the name of devices on bus to avoid
device names collisions for same client UUID available
from different MEI heads. Namely this prevents sysfs collision under
/sys/bus/mei/device/
In the device part leave just UUID other parameters that are
required for device matching are not required here and are
just bloating the name.
Cc: <stable@vger.kernel.org> Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Link: https://lore.kernel.org/r/20191105150514.14010-1-tomas.winkler@intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
This device presents itself as a USB hub with three attached devices:
- An ACM serial port connected to the GPS module (not affected by this
commit)
- An FTDI serial port connected to the GPS module (1546:0502)
- Another FTDI serial port connected to the ODIN-W2 radio module
(1546:0503)
This commit registers U-Blox's VID and the PIDs of the second and third
devices.
Add 024c:0525 to the list of SDIO device-ids, based on a patch found
in the Android X86 kernels. According to that patch this device id is
used on the Alcatel Plus 10 device.
The driver only binds by SDIO device-ids, all the ACPI device-id does
is causing the driver to load unnecessarily on devices where the DSDT
contains a bogus OBDA8723 device.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191111113846.24940-2-hdegoede@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The variable skb is released via kfree_skb() when the return value of
_rtl92e_tx is not zero. However, after that, skb is accessed again to
read its length, which may result in a use after free bug. This patch
fixes the bug by moving the release operation to where skb is never
used later.
Do not copy the extended supported rates in 'param->supp_rates' if the
array is already full with basic rates values. The array size check
helped to avoid possible illegal memory access [1] while copying to
'param->supp_rates' array.
Testing on different generations of Lantiq MIPS SoC based boards, showed
that it takes up to 1500 us until the core reset bit is cleared.
The driver from the vendor SDK (ifxhcd) uses a 1 second timeout. Use the
same timeout to fix wrong hang detections and make the driver work for
Lantiq MIPS SoCs.
At least till kernel 4.14 the hanging reset only caused a warning but
the driver was probed successful. With kernel 4.19 errors out with
EBUSY.
platform_find_device_by_driver calls bus_find_device and passes
platform_match as the callback function. Casting the function to a
mismatching type trips indirect call Control-Flow Integrity (CFI) checking.
This change adds a callback function with the correct type and instead
of casting the function, explicitly casts the second parameter to struct
device_driver* as expected by platform_match.
This patch corrects an error in the Transform Record Cache initialization
code that was causing intermittent stability problems on the Macchiatobin
board.
Unfortunately, due to HW platform specifics, the problem could not happen
on the main development platform, being the VCU118 Xilinx development
board. And since it was a problem with hash table access, it was very
dependent on the actual physical context record DMA buffers being used,
i.e. with some (bad) luck it could seemingly work quit stable for a while.
Signed-off-by: Pascal van Leeuwen <pvanleeuwen@verimatrix.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Only io_uring uses (and added) these, and we want to disallow the
use of sendmsg/recvmsg for anything but regular data transfers.
Use the newly added prep helper to split the msghdr copy out from
the core function, to check for msg_control and msg_controllen
settings. If either is set, we return -EINVAL.
Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
projects / mirror_ubuntu-focal-kernel.git / log