The firmware is offering features such as ARP offload, for which
firmware crafts its own (QoS)packets without waking up the host.
Point is that the sequence numbers generated by the firmware are
not in sync with the host mac80211 layer and can cause packets
such as firmware ARP reponses to be dropped by the AP (too old SN).
To fix this we need to let the firmware manages the sequence
numbers by its own (except for QoS null frames). There is a SN
counter for each QoS queue and one global/baseline counter for
Non-QoS.
Fixes: 84aff52e4f57 ("wcn36xx: Use sequence number allocated by mac80211") Signed-off-by: Loic Poulain <loic.poulain@linaro.org> Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1635150336-18736-1-git-send-email-loic.poulain@linaro.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
This is essentially exactly following the dma_wmb()/dma_rmb() usage
instructions in Documentation/memory-barriers.txt.
The theoretical races here are:
1. DXE (the DMA Transfer Engine in the Wi-Fi subsystem) seeing the
dxe->ctrl & WCN36xx_DXE_CTRL_VLD write before the dxe->dst_addr_l
write, thus performing DMA into the wrong address.
2. CPU reading dxe->dst_addr_l before DXE unsets dxe->ctrl &
WCN36xx_DXE_CTRL_VLD. This should generally be harmless since DXE
doesn't write dxe->dst_addr_l (no risk of freeing the wrong skb).
Fixes: 8e84c2582169 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware") Signed-off-by: Benjamin Li <benl@squareup.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211023001528.3077822-1-benl@squareup.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
cardp is missing being freed in the error handling path of the probe
and the path of the disconnect, which will cause memory leak.
This patch adds the missing kfree().
Fixes: 876c9d3aeb98 ("[PATCH] Marvell Libertas 8388 802.11b/g USB driver") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211020120345.2016045-3-wanghai38@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
cardp is missing being freed in the error handling path of the probe
and the path of the disconnect, which will cause memory leak.
This patch adds the missing kfree().
Fixes: c305a19a0d0a ("libertas_tf: usb specific functions") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211020120345.2016045-2-wanghai38@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
If handle_sske cannot set the storage key, because there is no
page table entry or no present large page entry, it calls
fixup_user_fault.
However, currently, if the call succeeds, handle_sske returns
-EAGAIN, without having set the storage key.
Instead, retry by continue'ing the loop without incrementing the
address.
The same issue in handle_pfmf was fixed by a11bdb1a6b78 ("KVM: s390: Fix pfmf and conditional skey emulation").
Fixes: bd096f644319 ("KVM: s390: Add skey emulation fault handling") Signed-off-by: Janis Schoetterl-Glausch <scgl@linux.ibm.com> Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com> Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com> Link: https://lore.kernel.org/r/20211022152648.26536-1-scgl@linux.ibm.com Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Use the actual return value instead of always -1 if register_kretprobe()
failed.
E.g. without this patch:
# insmod samples/kprobes/kretprobe_example.ko func=no_such_func
insmod: ERROR: could not insert module samples/kprobes/kretprobe_example.ko: Operation not permitted
With this patch:
# insmod samples/kprobes/kretprobe_example.ko func=no_such_func
insmod: ERROR: could not insert module samples/kprobes/kretprobe_example.ko: Unknown symbol in module
Link: https://lkml.kernel.org/r/1635213091-24387-2-git-send-email-yangtiezhu@loongson.cn Fixes: 804defea1c02 ("Kprobes: move kprobe examples to samples/") Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn> Acked-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Fix a problem in active mode that cpu->pstate.turbo_freq is initialized
only if HWP-to-frequency scaling factor is refined.
In passive mode, this problem is not exposed, because
cpu->pstate.turbo_freq is set again, later in
intel_cpufreq_cpu_init()->intel_pstate_get_hwp_cap().
Fixes: eb3693f0521e ("cpufreq: intel_pstate: hybrid: CPU-specific scaling factor") Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
v1: Implement a more general statement as recommended by Eric Dumazet. The
sequence number will be advanced, so this check will fix the FIN case and
other cases.
A customer reported sockets stuck in the CLOSING state. A Vmcore revealed that
the write_queue was not empty as determined by tcp_write_queue_empty() but the
sk_buff containing the FIN flag had been freed and the socket was zombied in
that state. Corresponding pcaps show no FIN from the Linux kernel on the wire.
Some instrumentation was added to the kernel and it was found that there is a
timing window where tcp_sendmsg() can run after tcp_send_fin().
tcp_remove_empty_skb() will then free the FIN sk_buff as "skb->len == 0". The
TCP socket is now wedged in the FIN-WAIT-1 state because the FIN is never sent.
If the other side sends a FIN packet the socket will transition to CLOSING and
remain that way until the system is rebooted.
Fix this by checking for the FIN flag in the sk_buff and don't free it if that
is the case. Testing confirmed that fixed the issue.
Fixes: fdfc5c8594c2 ("tcp: remove empty skb from write queue in error cases") Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com> Reported-by: Monir Zouaoui <Monir.Zouaoui@mail.schwarz> Reported-by: Simon Stier <simon.stier@mail.schwarz> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
__BYTE_ORDER is supposed to be defined by a libc, and __BYTE_ORDER__ -
by a compiler. bpf_core_read.h checks __BYTE_ORDER == __LITTLE_ENDIAN,
which is true if neither are defined, leading to incorrect behavior on
big-endian hosts if libc headers are not included, which is often the
case.
Fixes: ee26dade0e3b ("libbpf: Add support for relocatable bitfields") Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Link: https://lore.kernel.org/bpf/20211026010831.748682-2-iii@linux.ibm.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
In commit c46ed2281bbe ("tpm_tis_spi: add missing SPI device ID entries")
we added SPI IDs for all the DT aliases to handle the fact that we always
use SPI modaliases to load modules even when probed via DT however the
mentioned commit missed that the SPI and OF device ID entries did not
match and were different and so DT nodes with compatible
"tcg,tpm_tis-spi" will not match. Add an extra ID for tpm_tis-spi
rather than just fix the existing one since what's currently there is
going to be better for anyone actually using SPI IDs to instantiate.
Fixes: c46ed2281bbe ("tpm_tis_spi: add missing SPI device ID entries") Fixes: 96c8395e2166 ("spi: Revert modalias changes") Signed-off-by: Mark Brown <broonie@kernel.org> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Reviewed-by: Javier Martinez Canillas <javierm@redhat.com> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
The Atmel TPM 1.2 chips crash with error
`tpm_try_transmit: send(): error -62` since kernel 4.14.
It is observed from the kernel log after running `tpm_sealdata -z`.
The error thrown from the command is as follows
```
$ tpm_sealdata -z
Tspi_Key_LoadKey failed: 0x00001087 - layer=tddl,
code=0087 (135), I/O error
```
The issue was reproduced with the following Atmel TPM chip:
```
$ tpm_version
T0 TPM 1.2 Version Info:
Chip Version: 1.2.66.1
Spec Level: 2
Errata Revision: 3
TPM Vendor ID: ATML
TPM Version: 01010000
Manufacturer Info: 41544d4c
```
The root cause of the issue is due to the TPM calls to msleep()
were replaced with usleep_range() [1], which reduces
the actual timeout. Via experiments, it is observed that
the original msleep(5) actually sleeps for 15ms.
Because of a known timeout issue in Atmel TPM 1.2 chip,
the shorter timeout than 15ms can cause the error described above.
A few further changes in kernel 4.16 [2] and 4.18 [3, 4] further
reduced the timeout to less than 1ms. With experiments,
the problematic timeout in the latest kernel is the one
for `wait_for_tpm_stat`.
To fix it, the patch reverts the timeout of `wait_for_tpm_stat`
to 15ms for all Atmel TPM 1.2 chips, but leave it untouched
for Ateml TPM 2.0 chip, and chips from other vendors.
As explained above, the chosen 15ms timeout is
the actual timeout before this issue introduced,
thus the old value is used here.
Particularly, TPM_ATML_TIMEOUT_WAIT_STAT_MIN is set to 14700us,
TPM_ATML_TIMEOUT_WAIT_STAT_MIN is set to 15000us according to
the existing TPM_TIMEOUT_RANGE_US (300us).
The fixed has been tested in the system with the affected Atmel chip
with no issues observed after boot up.
References:
[1] 9f3fc7bcddcb tpm: replace msleep() with usleep_range() in TPM
1.2/2.0 generic drivers
[2] cf151a9a44d5 tpm: reduce tpm polling delay in tpm_tis_core
[3] 59f5a6b07f64 tpm: reduce poll sleep time in tpm_transmit()
[4] 424eaf910c32 tpm: reduce polling time to usecs for even finer
granularity
Fixes: 9f3fc7bcddcb ("tpm: replace msleep() with usleep_range() in TPM 1.2/2.0 generic drivers") Link: https://patchwork.kernel.org/project/linux-integrity/patch/20200926223150.109645-1-hao.wu@rubrik.com/ Signed-off-by: Hao Wu <hao.wu@rubrik.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Because blkcg_deactivate_policy() requires queue to be frozen, we can
grab q_usage_counter to synchoronize blkg_conf_prep() against
blkcg_deactivate_policy().
Fixes: e21b7a0b9887 ("block, bfq: add full hierarchical scheduling and cgroups support") Signed-off-by: Yu Kuai <yukuai3@huawei.com> Acked-by: Tejun Heo <tj@kernel.org> Link: https://lore.kernel.org/r/20211020014036.2141723-1-yukuai3@huawei.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
As it turns out, my earlier patch in commit 86d46fdaa12a (block:
ataflop: fix breakage introduced at blk-mq refactoring) was
incomplete. This patch fixes any remaining issues found during
more testing and code review.
Requests exceeding 4 k are handled in 4k segments but
__blk_mq_end_request() is never called on these (still
sectors outstanding on the request). With redo_fd_request()
removed, there is no provision to kick off processing of the
next segment, causing requests exceeding 4k to hang. (By
setting /sys/block/fd0/queue/max_sectors_k <= 4 as workaround,
this behaviour can be avoided).
Instead of reintroducing redo_fd_request(), requeue the remainder
of the request by calling blk_mq_requeue_request() on incomplete
requests (i.e. when blk_update_request() still returns true), and
rely on the block layer to queue the residual as new request.
Both error handling and formatting needs to release the
ST-DMA lock, so call finish_fdc() on these (this was previously
handled by redo_fd_request()). finish_fdc() may be called
legitimately without the ST-DMA lock held - make sure we only
release the lock if we actually held it. In a similar way,
early exit due to errors in ataflop_queue_rq() must release
the lock.
After minor errors, fd_error sets up to recalibrate the drive
but never re-runs the current operation (another task handled by
redo_fd_request() before). Call do_fd_action() to get the next
steps (seek, retry read/write) underway.
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com> Fixes: 6ec3938cff95f (ataflop: convert to blk-mq) CC: linux-block@vger.kernel.org Link: https://lore.kernel.org/r/20211024002013.9332-1-schmitzmic@gmail.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Commit 9af7c32ceca8 ("ath10k: add target IRAM recovery feature support")
introduced a new firmware feature flag ATH10K_FW_FEATURE_IRAM_RECOVERY. But
this caused ath10k_pci module load to fail if ATH10K_FW_CRASH_DUMP_RAM_DATA bit
was not enabled in the ath10k coredump_mask module parameter:
[ 2209.328190] ath10k_pci 0000:02:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
[ 2209.434414] ath10k_pci 0000:02:00.0: kconfig debug 1 debugfs 1 tracing 1 dfs 1 testmode 1
[ 2209.547191] ath10k_pci 0000:02:00.0: firmware ver 10.4-3.9.0.2-00099 api 5 features no-p2p,mfp,peer-flow-ctrl,btcoex-param,allows-mesh-bcast,no-ps,peer-fixed-rate,iram-recovery crc32 cbade90a
[ 2210.896485] ath10k_pci 0000:02:00.0: board_file api 1 bmi_id 0:1 crc32 a040efc2
[ 2213.603339] ath10k_pci 0000:02:00.0: failed to copy target iram contents: -12
[ 2213.839027] ath10k_pci 0000:02:00.0: could not init core (-12)
[ 2213.933910] ath10k_pci 0000:02:00.0: could not probe fw (-12)
And by default coredump_mask does not have ATH10K_FW_CRASH_DUMP_RAM_DATA
enabled so anyone using a firmware with iram-recovery feature would fail. To my
knowledge only QCA9984 firmwares starting from release 10.4-3.9.0.2-00099
enabled the feature.
The reason for regression was that ath10k_core_copy_target_iram() used
ath10k_coredump_get_mem_layout() to get the memory layout, but when
ATH10K_FW_CRASH_DUMP_RAM_DATA was disabled it would get just NULL and bail out
with an error.
While looking at all this I noticed another bug: if CONFIG_DEV_COREDUMP is
disabled but the firmware has iram-recovery enabled the module load fails with
similar error messages. I fixed that by returning 0 from
ath10k_core_copy_target_iram() when _ath10k_coredump_get_mem_layout() returns
NULL.
Tested-on: QCA9984 hw2.0 PCI 10.4-3.9.0.2-00139
Fixes: 9af7c32ceca8 ("ath10k: add target IRAM recovery feature support") Signed-off-by: Abinaya Kalaiselvan <akalaise@codeaurora.org> Signed-off-by: Jouni Malinen <jouni@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211020075054.23061-1-kvalo@codeaurora.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
At present, when either of ds->ops->port_fdb_del() or ds->ops->port_mdb_del()
return a non-zero error code, we attempt to save the day and keep the
data structure associated with that switchdev object, as the deletion
procedure did not complete.
However, the way in which we do this is suspicious to the checker in
lib/refcount.c, who thinks it is buggy to increment a refcount that
became zero, and that this is indicative of a use-after-free.
Fixes: 161ca59d39e9 ("net: dsa: reference count the MDB entries at the cross-chip notifier level") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
As bcm6345_l1_irq_handle() is a chained irqchip handler, it will be
invoked within the context of the root irqchip handler, which must have
entered IRQ context already.
When bcm6345_l1_irq_handle() calls arch/mips's do_IRQ() , this will nest
another call to irq_enter(), and the resulting nested increment to
`rcu_data.dynticks_nmi_nesting` will cause rcu_is_cpu_rrupt_from_idle()
to fail to identify wakeups from idle, resulting in failure to preempt,
and RCU stalls.
Chained irqchip handlers must invoke IRQ handlers by way of thee core
irqchip code, i.e. generic_handle_irq() or generic_handle_domain_irq()
and should not call do_IRQ(), which is intended only for root irqchip
handlers.
Fix bcm6345_l1_irq_handle() by calling generic_handle_irq() directly.
Fixes: c7c42ec2baa1de7a ("irqchips/bmips: Add bcm6345-l1 interrupt controller") Signed-off-by: Mark Rutland <mark.rutland@arm.com> Reviewed-by: Marc Zyngier <maz@kernel.org> Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
If kvm_s390_pv_destroy_cpu is called more than once, we risk calling
free_page on a random page, since the sidad field is aliased with the
gbea, which is not guaranteed to be zero.
This can happen, for example, if userspace calls the KVM_PV_DISABLE
IOCTL, and it fails, and then userspace calls the same IOCTL again.
This scenario is only possible if KVM has some serious bug or if the
hardware is broken.
The solution is to simply return successfully immediately if the vCPU
was already non secure.
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com> Fixes: 19e1227768863a1469797c13ef8fea1af7beac2c ("KVM: S390: protvirt: Introduce instruction data area bounce buffer") Reviewed-by: Janosch Frank <frankja@linux.ibm.com> Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <20210920132502.36111-3-imbrenda@linux.ibm.com> Signed-off-by: Janosch Frank <frankja@linux.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
We should not walk/touch page tables outside of VMA boundaries when
holding only the mmap sem in read mode. Evil user space can modify the
VMA layout just before this function runs and e.g., trigger races with
page table removal code since commit dd2283f2605e ("mm: mmap: zap pages
with read mmap_sem in munmap").
find_vma() does not check if the address is >= the VMA start address;
use vma_lookup() instead.
Fixes: 214d9bbcd3a6 ("s390/mm: provide memory management functions for protected KVM guests") Signed-off-by: David Hildenbrand <david@redhat.com> Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com> Acked-by: Heiko Carstens <hca@linux.ibm.com> Reviewed-by: Liam R. Howlett <Liam.Howlett@oracle.com> Link: https://lore.kernel.org/r/20210909162248.14969-6-david@redhat.com Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
There are multiple things broken about our storage key handling
functions:
1. We should not walk/touch page tables outside of VMA boundaries when
holding only the mmap sem in read mode. Evil user space can modify the
VMA layout just before this function runs and e.g., trigger races with
page table removal code since commit dd2283f2605e ("mm: mmap: zap pages
with read mmap_sem in munmap"). gfn_to_hva() will only translate using
KVM memory regions, but won't validate the VMA.
2. We should not allocate page tables outside of VMA boundaries: if
evil user space decides to map hugetlbfs to these ranges, bad things
will happen because we suddenly have PTE or PMD page tables where we
shouldn't have them.
3. We don't handle large PUDs that might suddenly appeared inside our page
table hierarchy.
Don't manually allocate page tables, properly validate that we have VMA and
bail out on pud_large().
All callers of page table handling functions, except
get_guest_storage_key(), call fixup_user_fault() in case they
receive an -EFAULT and retry; this will allocate the necessary page tables
if required.
To keep get_guest_storage_key() working as expected and not requiring
kvm_s390_get_skeys() to call fixup_user_fault() distinguish between
"there is simply no page table or huge page yet and the key is assumed
to be 0" and "this is a fault to be reported".
Although commit 637ff9efe5ea ("s390/mm: Add huge pmd storage key handling")
introduced most of the affected code, it was actually already broken
before when using get_locked_pte() without any VMA checks.
Note: Ever since commit 637ff9efe5ea ("s390/mm: Add huge pmd storage key
handling") we can no longer set a guest storage key (for example from
QEMU during VM live migration) without actually resolving a fault.
Although we would have created most page tables, we would choke on the
!pmd_present(), requiring a call to fixup_user_fault(). I would
have thought that this is problematic in combination with postcopy life
migration ... but nobody noticed and this patch doesn't change the
situation. So maybe it's just fine.
Fixes: 9fcf93b5de06 ("KVM: S390: Create helper function get_guest_storage_key") Fixes: 24d5dd0208ed ("s390/kvm: Provide function for setting the guest storage key") Fixes: a7e19ab55ffd ("KVM: s390: handle missing storage-key facility") Signed-off-by: David Hildenbrand <david@redhat.com> Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com> Acked-by: Heiko Carstens <hca@linux.ibm.com> Link: https://lore.kernel.org/r/20210909162248.14969-5-david@redhat.com Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
We should not walk/touch page tables outside of VMA boundaries when
holding only the mmap sem in read mode. Evil user space can modify the
VMA layout just before this function runs and e.g., trigger races with
page table removal code since commit dd2283f2605e ("mm: mmap: zap pages
with read mmap_sem in munmap"). gfn_to_hva() will only translate using
KVM memory regions, but won't validate the VMA.
Further, we should not allocate page tables outside of VMA boundaries: if
evil user space decides to map hugetlbfs to these ranges, bad things will
happen because we suddenly have PTE or PMD page tables where we
shouldn't have them.
Similarly, we have to check if we suddenly find a hugetlbfs VMA, before
calling get_locked_pte().
Fixes: 2d42f9477320 ("s390/kvm: Add PGSTE manipulation functions") Signed-off-by: David Hildenbrand <david@redhat.com> Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com> Acked-by: Heiko Carstens <hca@linux.ibm.com> Link: https://lore.kernel.org/r/20210909162248.14969-4-david@redhat.com Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
... otherwise we will try unlocking a spinlock that was never locked via a
garbage pointer.
At the time we reach this code path, we usually successfully looked up
a PGSTE already; however, evil user space could have manipulated the VMA
layout in the meantime and triggered removal of the page table.
Fixes: 1e133ab296f3 ("s390/mm: split arch/s390/mm/pgtable.c") Signed-off-by: David Hildenbrand <david@redhat.com> Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com> Acked-by: Heiko Carstens <hca@linux.ibm.com> Link: https://lore.kernel.org/r/20210909162248.14969-3-david@redhat.com Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
We should not walk/touch page tables outside of VMA boundaries when
holding only the mmap sem in read mode. Evil user space can modify the
VMA layout just before this function runs and e.g., trigger races with
page table removal code since commit dd2283f2605e ("mm: mmap: zap pages
with read mmap_sem in munmap"). The pure prescence in our guest_to_host
radix tree does not imply that there is a VMA.
Further, we should not allocate page tables (via get_locked_pte()) outside
of VMA boundaries: if evil user space decides to map hugetlbfs to these
ranges, bad things will happen because we suddenly have PTE or PMD page
tables where we shouldn't have them.
Similarly, we have to check if we suddenly find a hugetlbfs VMA, before
calling get_locked_pte().
Note that gmap_discard() is different:
zap_page_range()->unmap_single_vma() makes sure to stay within VMA
boundaries.
Fixes: b31288fa83b2 ("s390/kvm: support collaborative memory management") Signed-off-by: David Hildenbrand <david@redhat.com> Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com> Acked-by: Heiko Carstens <hca@linux.ibm.com> Link: https://lore.kernel.org/r/20210909162248.14969-2-david@redhat.com Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
commit 7f4b7920318b ("mt76: mt7615: add ibss support") introduced IBSS
and commit f4ec7fdf7f83 ("mt76: mt7615: enable support for mesh")
meshpoint support.
Both used in the "get_omac_idx"-function:
if (~mask & BIT(HW_BSSID_0))
return HW_BSSID_0;
With commit d8d59f66d136 ("mt76: mt7615: support 16 interfaces") the
ibss and meshpoint mode should "prefer hw bssid slot 1-3". However,
with that change the ibss or meshpoint mode will not send any beacon on
the mt7622 wifi anymore. Devices were still able to exchange data but
only if a bssid already existed. Two mt7622 devices will never be able
to communicate.
This commits reverts the preferation of slot 1-3 for ibss and
meshpoint. Only NL80211_IFTYPE_STATION will still prefer slot 1-3.
Tested on Banana Pi R64.
Fixes: d8d59f66d136 ("mt76: mt7615: support 16 interfaces") Signed-off-by: Nick Hainke <vincent@systemli.org> Acked-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211007225725.2615-1-vincent@systemli.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Original code assumed fixed and correct BTF header length. That's not
always the case, though, so fix this bug with a proper additional check.
And use actual header length instead of sizeof(struct btf_header) in
sanity checks.
Fixes: 8a138aed4a80 ("bpf: btf: Add BTF support to libbpf") Reported-by: Evgeny Vereshchagin <evvers@ya.ru> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Link: https://lore.kernel.org/bpf/20211023003157.726961-2-andrii@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
btf_header's str_off+str_len or type_off+type_len can overflow as they
are u32s. This will lead to bypassing the sanity checks during BTF
parsing, resulting in crashes afterwards. Fix by using 64-bit signed
integers for comparison.
Fixes: d8123624506c ("libbpf: Fix BTF data layout checks and allow empty BTF") Reported-by: Evgeny Vereshchagin <evvers@ya.ru> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Link: https://lore.kernel.org/bpf/20211023003157.726961-1-andrii@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Bpftool creates a new JSON object for writing program metadata in plain
text mode, regardless of metadata being present or not. Then this writer
is freed if any metadata has been found and printed, but it leaks
otherwise. We cannot destroy the object unconditionally, because the
destructor prints an undesirable line break. Instead, make sure the
writer is created only after we have found program metadata to print.
Found with valgrind.
Fixes: aff52e685eb3 ("bpftool: Support dumping metadata") Signed-off-by: Quentin Monnet <quentin@isovalent.com> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Link: https://lore.kernel.org/bpf/20211022094743.11052-1-quentin@isovalent.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Though gcc conveniently compiles a simple memset to "rep stos," clang
prefers to call the libc version of memset. If a test is dynamically
linked, the libc memset isn't available in L1 (nor is the PLT or the
GOT, for that matter). Even if the test is statically linked, the libc
memset may choose to use some CPU features, like AVX, which may not be
enabled in L1. Note that __builtin_memset doesn't solve the problem,
because (a) the compiler is free to call memset anyway, and (b)
__builtin_memset may also choose to use features like AVX, which may
not be available in L1.
To avoid a myriad of problems, use an explicit "rep stos" to clear the
VMCB in generic_svm_setup(), which is called both from L0 and L1.
Reported-by: Ricardo Koller <ricarkol@google.com> Signed-off-by: Jim Mattson <jmattson@google.com> Fixes: 20ba262f8631a ("selftests: KVM: AMD Nested test infrastructure")
Message-Id: <20210930003649.4026553-1-jmattson@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
syzbot is reporting UAF at cipso_v4_doi_search() [1], for smk_cipso_doi()
is calling kfree() without removing from the cipso_v4_doi_list list after
netlbl_cfg_cipsov4_map_add() returned an error. We need to use
netlbl_cfg_cipsov4_del() in order to remove from the list and wait for
RCU grace period before kfree().
Commit ad6d66bcac77e ("crypto: tcrypt - include 1420 byte blocks in aead and skcipher benchmarks")
mentions:
> power-of-2 block size. So let's add 1420 bytes explicitly, and round
> it up to the next blocksize multiple of the algo in question if it
> does not support 1420 byte blocks.
but misses updating skcipher multi-buffer tests.
Fix this by using the proper (rounded) input size.
Fixes: ad6d66bcac77e ("crypto: tcrypt - include 1420 byte blocks in aead and skcipher benchmarks") Signed-off-by: Horia Geantă <horia.geanta@nxp.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Change byte_clk_rate, pixel_clk_rate, esc_clk_rate, and src_clk_rate
from u32 to unsigned long, since clk_get_rate() returns an unsigned long.
Fixes: a6bcddbc2ee1 ("drm/msm: dsi: Handle dual-channel for 6G as well") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Jessica Zhang <jesszhan@codeaurora.org> Link: https://lore.kernel.org/r/20211020183438.32263-1-jesszhan@codeaurora.org Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
When building OMAP_DM_TIMER without TIMER_OF, there are orphan sections
due to the use of TIMER_OF_DELCARE() without CONFIG_TIMER_OF. Select
CONFIG_TIMER_OF when enaling OMAP_DM_TIMER:
arm-linux-gnueabi-ld: warning: orphan section `__timer_of_table' from `drivers/clocksource/timer-ti-dm-systimer.o' being placed in section `__timer_of_table'
Reported-by: kernel test robot <lkp@intel.com> Link: https://lore.kernel.org/lkml/202108282255.tkdt4ani-lkp@intel.com/ Cc: Tony Lindgren <tony@atomide.com> Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: Keerthy <j-keerthy@ti.com> Cc: Sebastian Reichel <sebastian.reichel@collabora.co.uk> Cc: Ladislav Michl <ladis@linux-mips.org> Cc: Grygorii Strashko <grygorii.strashko@ti.com> Cc: linux-omap@vger.kernel.org Fixes: 52762fbd1c47 ("clocksource/drivers/timer-ti-dm: Add clockevent and clocksource support") Signed-off-by: Kees Cook <keescook@chromium.org> Acked-by: Tony Lindgren <tony@atomide.com> Link: https://lore.kernel.org/r/20210828175747.3777891-1-keescook@chromium.org Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
When building the kernel with sparse enabled 'C=1' the following
warnings shows up:
kernel/power/swap.c:390:29: warning: incorrect type in assignment (different base types)
kernel/power/swap.c:390:29: expected int ret
kernel/power/swap.c:390:29: got restricted blk_status_t
This is due to function hib_wait_io() returns a 'blk_status_t' which is
a bitwise u8. Commit 5416da01ff6e ("PM: hibernate: Remove
blk_status_to_errno in hib_wait_io") seemed to have mixed up the return
type. However, the 4e4cbee93d56 ("block: switch bios to blk_status_t")
actually broke the behaviour by returning the wrong type.
Rework so function hib_wait_io() returns a 'int' instead of
'blk_status_t' and make sure to call function
blk_status_to_errno(hb->error)' when returning from function
hib_wait_io() a int gets returned.
Fixes: 4e4cbee93d56 ("block: switch bios to blk_status_t") Fixes: 5416da01ff6e ("PM: hibernate: Remove blk_status_to_errno in hib_wait_io") Signed-off-by: Anders Roxell <anders.roxell@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
In case that icdoff is not zero or mandatory keyed sgls are not
supported by the NVMe/RDMA target, we'll go to error flow but we'll
return 0 to the caller. Fix it by returning an appropriate error code.
Fixes: c66e2998c8ca ("nvme-rdma: centralize controller setup sequence") Signed-off-by: Max Gurtovoy <mgurtovoy@nvidia.com> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Reproduce this issue as follows:
1. nbd-server 8000 /tmp/disk
2. nbd-client localhost 8000 /dev/nbd1
3. cat /sys/block/nbd1/pid
Then trigger use-after-free in pid_show.
Reason is after do step '2', nbd-client progress is already exit. So
it's task_struct already freed.
To solve this issue, revert part of 6521d39a64b3's modify and remove
useless 'recv_task' member of nbd_device.
Fixes: 6521d39a64b3 ("nbd: Remove variable 'pid'") Signed-off-by: Ye Bin <yebin10@huawei.com> Reviewed-by: Josef Bacik <josef@toxicpanda.com> Link: https://lore.kernel.org/r/20211020073959.2679255-1-yebin10@huawei.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Some Micrel KSZ8041NL PHY chips exhibit continuous RX errors after using
the power down mode bit (0.11). If the PHY is taken out of power down
mode in a certain temperature range, the PHY enters a weird state which
leads to continuously reporting RX errors. In that state, the MAC is not
able to receive or send any Ethernet frames and the activity LED is
constantly blinking. Since Linux is using the suspend callback when the
interface is taken down, ending up in that state can easily happen
during a normal startup.
Micrel confirmed the issue in errata DS80000700A [*], caused by abnormal
clock recovery when using power down mode. Even the latest revision (A4,
Revision ID 0x1513) seems to suffer that problem, and according to the
errata is not going to be fixed.
Remove the suspend/resume callback to avoid using the power down mode
completely.
Fixes: 1a5465f5d6a2 ("phy/micrel: Add suspend/resume support to Micrel PHYs") Signed-off-by: Stefan Agner <stefan@agner.ch> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
If resume fails for some reason, we need to set the PM state
back to normal so we're able to send commands during firmware
reset, rather than failing all of them because we're in D3.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Fixes: 708a39aaca22 ("iwlwifi: mvm: don't send commands during suspend\resume transition") Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/iwlwifi.20211016114029.7ceb9eaca9f6.If0cbef38c6d07ec1ddce125878a4bdadcb35d2c9@changeid Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
While looking at on-air packets using Wireshark, I noticed we're never
setting the initiator bit when sending DELBA requests to the AP: While
we set the bit on our del_ba_param_set bitmask, we forget to actually
copy that bitmask over to the command struct, which means we never
actually set the initiator bit.
Fix that and copy the bitmask over to the host_cmd_ds_11n_delba command
struct.
Fixes: 5e6e3a92b9a4 ("wireless: mwifiex: initial commit for Marvell mwifiex driver") Signed-off-by: Jonas Dreßler <verdre@v0yd.nl> Acked-by: Pali Rohár <pali@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211016153244.24353-5-verdre@v0yd.nl Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
When fail to init coex module, free 'common' and 'adapter' directly, but
common->tx_thread which will access 'common' and 'adapter' is running at
the same time. That will trigger the UAF bug.
==================================================================
BUG: KASAN: use-after-free in rsi_tx_scheduler_thread+0x50f/0x520 [rsi_91x]
Read of size 8 at addr ffff8880076dc000 by task Tx-Thread/124777
CPU: 0 PID: 124777 Comm: Tx-Thread Not tainted 5.15.0-rc5+ #19
Call Trace:
dump_stack_lvl+0xe2/0x152
print_address_description.constprop.0+0x21/0x140
? rsi_tx_scheduler_thread+0x50f/0x520
kasan_report.cold+0x7f/0x11b
? rsi_tx_scheduler_thread+0x50f/0x520
rsi_tx_scheduler_thread+0x50f/0x520
...
Stop thread before free 'common' and 'adapter' to fix it.
Fixes: 2108df3c4b18 ("rsi: add coex support") Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211015040335.1021546-1-william.xuanziyang@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Fixes: 67aa27431c7f8 ("mt76: mt7921: rely on mt76_connac_mcu common library") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
We should pass the error code to the caller immediately
to avoid the possible infinite retry to release the semaphore.
Fixes: 1c099ab44727 ("mt76: mt7921: add MCU support") Co-developed-by: YN Chen <YN.Chen@mediatek.com> Signed-off-by: YN Chen <YN.Chen@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Without this change, garbage is seen in the hwmon name and sensors output
for mt7915 is garbled. It appears that the hwmon logic does not make a
copy of the incoming string, but instead just copies a char* and expects
it to never go away.
Fixes: 33fe9c639c13 ("mt76: mt7915: add thermal sensor device support") Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Fixes: 1c099ab44727 ("mt76: mt7921: add MCU support") Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
According to the firmware usage, OFDM rates should fill out bit 6 - 13
while CCK rates should fill out bit 0 - 3 in legacy field of RA info to
make the rate adaption runs propertly. Otherwise, a unicast frame might be
picking up the unsupported rate to send out.
Fixes: 1c099ab44727 ("mt76: mt7921: add MCU support") Reported-by: Joshua Emele <jemele@chromium.org> Co-developed-by: YN Chen <YN.Chen@mediatek.com> Signed-off-by: YN Chen <YN.Chen@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Introduce mt76_register_debugfs_fops routine in order to
define per-driver regs file operations and make sure the
device is up before reading or writing its registers
Fixes: 1d8efc741df8 ("mt76: mt7921: introduce Runtime PM support") Fixes: de5ff3c9d1a2 ("mt76: mt7615: introduce pm_power_save delayed work") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Update the proper firmware programming sequence to fix GTK rekey
offload failure on WPA mixed mode.
In the mt76_connac_mcu_key_iter,
gtk_tlv->proto should be only set up on pairwise key
and gtk_tlk->group_cipher should be only set up on the group key.
Otherwise, those parameters required by firmware would be set
incorrectly to cause GTK rekey offload failure on WPA mixed mode
and then disconnection follows.
Fixes: b47e21e75c80 ("mt76: mt7615: add gtk rekey offload support") Co-developed-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Leon Yen <Leon.Yen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
The dma would be broken after rmmod flow. There are two different
cases causing this issue.
1. dma access without privilege.
2. hw access sequence borken by another context.
This patch handle both cases to avoid hw crash.
Fixes: 2b9ea5a8cf1bd ("mt76: mt7921: add mt7921_dma_cleanup in mt7921_unregister_device") Signed-off-by: Deren Wu <deren.wu@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
The bit fields of tx rate idx should be 6 bits, otherwise it might be
incorrect in HT mode.
For VHT/HE rates, only 4 bits are actually used by rate idx, the other
2 bits are used for other functions.
Fixes: c31d94af1843 ("mt76: mt7915: fix tx rate related fields in tx descriptor") Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
If total eeprom size is divisible by per-page size, the i in for loop
will exceed max page index, which happens in our newer chipset.
Fixes: 26f18380e6ca ("mt76: mt7915: add support for flash mode") Signed-off-by: Bo Jiao <bo.jiao@mediatek.com> Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
The acceptable event report should inlcude original CMD-ID. Otherwise,
drop unexpected result from fw.
Fixes: 1c099ab44727c ("mt76: mt7921: add MCU support") Signed-off-by: Jimmy Hu <Jimmy.Hu@mediatek.com> Signed-off-by: Deren Wu <deren.wu@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Fix the following sparse warning in mt76x02_mac_write_txwi and
mt76x02_mac_tx_rate_val routines:
drivers/net/wireless/mediatek/mt76/mt76x02_mac.c:237:19:
warning: restricted __le16 degrades to intege
warning: cast from restricted __le16
drivers/net/wireless/mediatek/mt76/mt76x02_mac.c:383:28:
warning: incorrect type in assignment (different base types)
expected restricted __le16 [usertype] rate
got unsigned long
Fixes: db9f11d3433f7 ("mt76: store wcid tx rate info in one u32 reduce locking") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Fix MIB tx-rx MIB counters for survey-dump reporting.
Fixes: 163f4d22c118d ("mt76: mt7921: add MAC support") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:114:10: error: implicit
conversion from enumeration type 'enum mt76_cipher_type' to different
enumeration type 'enum mcu_cipher_type' [-Werror,-Wenum-conversion]
return MT_CIPHER_NONE;
~~~~~~ ^~~~~~~~~~~~~~
drivers/net/wireless/mediatek/mt76/mt7921/mcu.c:114:10: error: implicit
conversion from enumeration type 'enum mt76_cipher_type' to different
enumeration type 'enum mcu_cipher_type' [-Werror,-Wenum-conversion]
return MT_CIPHER_NONE;
~~~~~~ ^~~~~~~~~~~~~~
Fixes: c368362c36d3 ("mt76: fix iv and CCMP header insertion") Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
The mistaken structure is introduced since we added the GTK rekey offload
to mt7663. The patch fixes mt76_connac_gtk_rekey_tlv structure according
to the MT7663 and MT7921 firmware we have submitted into
linux-firmware.git.
Fixes: b47e21e75c80 ("mt76: mt7615: add gtk rekey offload support") Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Leon Yen <Leon.Yen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Zero out all the unused members of "req" so that we don't disclose
stack information.
Fixes: 495184ac91bb ("mt76: mt7915: add support for applying pre-calibration data") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Fix the following sparse warning in mt7615_mac_write_txwi routine:
drivers/net/wireless/mediatek/mt76/mt7615/mac.c:758:17:
warning: incorrect type in assignment
expected restricted __le32 [usertype]
got unsigned long
Fixes: 04b8e65922f63 ("mt76: add mac80211 driver for MT7615 PCIe-based chipsets") Fixes: d4bf77bd74930 ("mt76: mt7615: introduce mt7663u support to mt7615_write_txwi") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Fix the following sparse warning in mt7921_update_txs routine:
drivers/net/wireless/mediatek/mt76/mt7921/mac.c:752:31:
warning: cast to restricted __le32
drivers/net/wireless/mediatek/mt76/mt7921/mac.c:752:31:
warning: restricted __le32 degrades to integer
Fixes: e5bca8c5d2cd3 ("mt76: mt7921: improve code readability for mt7921_update_txs") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Fix the following sparse warning in mt7915_mac_add_txs_skb routine:
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:1235:29:
warning: cast to restricted __le32
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:1235:23:
warning: restricted __le32 degrades to integer
Fixes: 3de4cb1756565 ("mt76: mt7915: add support for tx status reporting") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Fix endianness in mt7921_mcu_tx_done_event event reported by the
firmware.
Fixes: 3cce2b98e0241 ("mt76: mt7921: introduce mac tx done handling") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
We should unreference a gem object instead of an amdgpu bo here.
Fixes: fd9a9f8801de ("drm/amdgpu: Use GEM obj reference for KFD BOs") Signed-off-by: Lang Yu <lang.yu@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
If an ACPI wakeup power resource is shared between multiple devices,
it may not be managed correctly.
Suppose, for example, that two devices, A and B, share a wakeup power
resource P whose wakeup_enabled flag is 0 initially. Next, suppose
that wakeup power is enabled for A and B, in this order, and disabled
for B. When wakeup power is enabled for A, P will be turned on and
its wakeup_enabled flag will be set. Next, when wakeup power is
enabled for B, P will not be touched, because its wakeup_enabled flag
is set. Now, when wakeup power is disabled for B, P will be turned
off which is incorrect, because A will still need P in order to signal
wakeup.
Moreover, if wakeup power is enabled for A and then disabled for B,
the latter will cause P to be turned off incorrectly (it will be still
needed by A), because acpi_disable_wakeup_device_power() is allowed
to manipulate power resources when the wakeup.prepare_count counter
of the given device is 0.
While the first issue could be addressed by changing the
wakeup_enabled power resource flag into a counter, addressing the
second one requires modifying acpi_disable_wakeup_device_power() to
do nothing when the target device's wakeup.prepare_count reference
counter is zero and that would cause the new counter to be redundant.
Namely, if acpi_disable_wakeup_device_power() is modified as per the
above, every change of the new counter following a wakeup.prepare_count
change would be reflected by the analogous change of the main reference
counter of the given power resource.
Accordingly, modify acpi_disable_wakeup_device_power() to do nothing
when the target device's wakeup.prepare_count reference counter is
zero and drop the power resource wakeup_enabled flag altogether.
While at it, ensure that all of the power resources that can be
turned off will be turned off when disabling device wakeup due to
a power resource manipulation error, to prevent energy from being
wasted.
Fixes: b5d667eb392e ("ACPI / PM: Take unusual configurations of power resources into account") Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
If an ACPI power resource is found to be "on" during the
initialization of the list of wakeup power resources of a device,
it is reference counted and its wakeup_enabled flag is set, which is
problematic if the deivce in question is the only user of the given
power resource, it is never runtime-suspended and it is not allowed
to wake up the system from sleep, because in that case the given
power resource will stay "on" until the system reboots and energy
will be wasted.
It is better to simply turn off wakeup power resources that are "on"
during the initialization unless their reference counters are not
zero, because that may be the only opportunity to prevent them from
staying in the "on" state all the time.
Fixes: b5d667eb392e ("ACPI / PM: Take unusual configurations of power resources into account") Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
In the probe function, the clock IDs were pointed to local variables
which should only be used in the same code block, and any access to them
after the probing stage becomes an use-after-free case.
Since there are only limited variants of the gce clock names so far, we
can just declare them as static constants to fix the issue.
Fixes: 85dfdbfc13ea ("mailbox: cmdq: add multi-gce clocks support for mt8195") Signed-off-by: Fei Shao <fshao@chromium.org> Reviewed-by: Tzung-Bi Shih <tzungbi@google.com> Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
of_alias_get_id() may return -ENODEV which leads to illegal access to
the cmdq->clocks array.
Adding a check over alias_id to prevent the unexpected behavior.
Fixes: 85dfdbfc13ea ("mailbox: cmdq: add multi-gce clocks support for mt8195") Signed-off-by: Fei Shao <fshao@chromium.org> Reviewed-by: Tzung-Bi Shih <tzungbi@google.com> Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
A new warning in clang points out a use of bitwise OR with boolean
expressions in this driver:
drivers/platform/x86/thinkpad_acpi.c:9061:11: error: use of bitwise '|' with boolean operands [-Werror,-Wbitwise-instead-of-logical]
else if ((strlencmp(cmd, "level disengaged") == 0) |
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
||
drivers/platform/x86/thinkpad_acpi.c:9061:11: note: cast one or both operands to int to silence this warning
1 error generated.
This should clearly be a logical OR so change it to fix the warning.
Fixes: fe98a52ce754 ("ACPI: thinkpad-acpi: add sysfs support to fan subdriver") Link: https://github.com/ClangBuiltLinux/linux/issues/1476 Reported-by: Tor Vic <torvic9@mailbox.org> Signed-off-by: Nathan Chancellor <nathan@kernel.org> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Link: https://lore.kernel.org/r/20211018182537.2316800-1-nathan@kernel.org Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
The timer callback used to evaluate if the latency is exceeded can be
executed after the corresponding disk has been released, causing the
following NULL pointer dereference:
Refactoring of the Atari floppy driver when converting to blk-mq
has broken the state machine in not-so-subtle ways:
finish_fdc() must be called when operations on the floppy device
have completed. This is crucial in order to relase the ST-DMA
lock, which protects against concurrent access to the ST-DMA
controller by other drivers (some DMA related, most just related
to device register access - broken beyond compare, I know).
When rewriting the driver's old do_request() function, the fact
that finish_fdc() was called only when all queued requests had
completed appears to have been overlooked. Instead, the new
request function calls finish_fdc() immediately after the last
request has been queued. finish_fdc() executes a dummy seek after
most requests, and this overwrites the state machine's interrupt
hander that was set up to wait for completion of the read/write
request just prior. To make matters worse, finish_fdc() is called
before device interrupts are re-enabled, making certain that the
read/write interupt is missed.
Shifting the finish_fdc() call into the read/write request
completion handler ensures the driver waits for the request to
actually complete. With a queue depth of 2, we won't see long
request sequences, so calling finish_fdc() unconditionally just
adds a little overhead for the dummy seeks, and keeps the code
simple.
While we're at it, kill ataflop_commit_rqs() which does nothing
but run finish_fdc() unconditionally, again likely wiping out an
in-flight request.
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com> Fixes: 6ec3938cff95 ("ataflop: convert to blk-mq") CC: linux-block@vger.kernel.org CC: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp> Link: https://lore.kernel.org/r/20211019061321.26425-1-schmitzmic@gmail.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
commit f0c15b360fb6 ("media: ir_toy: prevent device from hanging during
transmit") removed a cpu_to_be16() cast, which causes a sparse warning.
Fixes: f0c15b360fb6 ("media: ir_toy: prevent device from hanging during transmit") Reported-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Prevent the use of page table macros and types from 2 conflicting
places. This fixes multiple build errors and warnings, e.g.:
../arch/x86/include/asm/pgtable_64_types.h:21:34: error: conflicting types for ‘pte_t’
typedef struct { pteval_t pte; } pte_t;
^~~~~
In file included from ../include/linux/mm_types_task.h:16:0,
from ../include/linux/mm_types.h:5,
from ../include/linux/buildid.h:5,
from ../include/linux/module.h:14,
from ../drivers/media/pci/ivtv/ivtv-driver.h:40,
from ../drivers/media/pci/ivtv/ivtvfb.c:29:
../arch/um/include/asm/page.h:57:39: note: previous declaration of ‘pte_t’ was here
typedef struct { unsigned long pte; } pte_t;
../arch/x86/include/asm/pgtable_types.h:284:43: error: expected ‘)’ before ‘prot’
static inline pgprot_t pgprot_nx(pgprot_t prot)
^
../include/linux/pgtable.h:914:26: note: in definition of macro ‘pgprot_nx’
#define pgprot_nx(prot) (prot)
^~~~
In file included from ../arch/x86/include/asm/memtype.h:6:0,
from ../drivers/media/pci/ivtv/ivtvfb.c:40:
../arch/x86/include/asm/pgtable_types.h:288:0: warning: "pgprot_nx" redefined
#define pgprot_nx pgprot_nx
In file included from ../include/linux/mm_types_task.h:16:0,
from ../include/linux/mm_types.h:5,
from ../include/linux/buildid.h:5,
from ../include/linux/module.h:14,
from ../drivers/media/pci/ivtv/ivtv-driver.h:40,
from ../drivers/media/pci/ivtv/ivtvfb.c:29:
../arch/um/include/asm/page.h:14:0: note: this is the location of the previous definition
#define PAGE_SIZE (_AC(1, UL) << PAGE_SHIFT)
Fixes: 68f5d3f3b654 ("um: add PCI over virtio emulation driver") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Johannes Berg <johannes@sipsolutions.net> Cc: Andy Walls <awalls@md.metrocast.net> Cc: linux-um@lists.infradead.org Cc: Richard Weinberger <richard@nod.at> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
aarch64-linux-gnu-ld: Unexpected GOT/PLT entries detected!
aarch64-linux-gnu-ld: Unexpected run-time procedure linkages detected!
aarch64-linux-gnu-ld: drivers/thermal/qcom/lmh.o: in function `lmh_probe':
/data/arm/workspace/kernel-build/linux/build/../drivers/thermal/qcom/lmh.c:141: undefined reference to `qcom_scm_lmh_dcvsh_available'
aarch64-linux-gnu-ld: /data/arm/workspace/kernel-build/linux/build/../drivers/thermal/qcom/lmh.c:144: undefined reference to `qcom_scm_lmh_dcvsh'
aarch64-linux-gnu-ld: /data/arm/workspace/kernel-build/linux/build/../drivers/thermal/qcom/lmh.c:149: undefined reference to `qcom_scm_lmh_dcvsh'
aarch64-linux-gnu-ld: /data/arm/workspace/kernel-build/linux/build/../drivers/thermal/qcom/lmh.c:154: undefined reference to `qcom_scm_lmh_dcvsh'
aarch64-linux-gnu-ld: /data/arm/workspace/kernel-build/linux/build/../drivers/thermal/qcom/lmh.c:159: undefined reference to `qcom_scm_lmh_dcvsh'
aarch64-linux-gnu-ld: /data/arm/workspace/kernel-build/linux/build/../drivers/thermal/qcom/lmh.c:166: undefined reference to `qcom_scm_lmh_profile_change'
aarch64-linux-gnu-ld: /data/arm/workspace/kernel-build/linux/build/../drivers/thermal/qcom/lmh.c:173: undefined reference to `qcom_scm_lmh_dcvsh'
aarch64-linux-gnu-ld: /data/arm/workspace/kernel-build/linux/build/../drivers/thermal/qcom/lmh.c:180: undefined reference to `qcom_scm_lmh_dcvsh'
aarch64-linux-gnu-ld: /data/arm/workspace/kernel-build/linux/build/../drivers/thermal/qcom/lmh.c:187: undefined reference to `qcom_scm_lmh_dcvsh'
make[1]: *** [/data/arm/workspace/kernel-build/linux/Makefile:1183: vmlinux] Error 1
make[1]: Leaving directory '/data/arm/workspace/kernel-build/linux/build'
make: *** [Makefile:219: __sub-make] Error 2
make: Leaving directory '/data/arm/workspace/kernel-build/linux'
Fixes: 53bca371cdf7 ("thermal/drivers/qcom: Add support for LMh driver") Signed-off-by: Jackie Liu <liuyun01@kylinos.cn> Link: https://lore.kernel.org/r/20211009015853.3509559-1-liu.yun@linux.dev Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
sk_stream_kill_queues() can be called on close when there are
still outstanding skbs to transmit. Those skbs may try to queue
notifications to the error queue (e.g. timestamps).
If sk_stream_kill_queues() purges the queue without taking
its lock the queue may get corrupted, and skbs leaked.
This shows up as a warning about an rmem leak:
WARNING: CPU: 24 PID: 0 at net/ipv4/af_inet.c:154 inet_sock_destruct+0x...
The leak is always a multiple of 0x300 bytes (the value is in
%rax on my builds, so RAX: 0000000000000300). 0x300 is truesize of
an empty sk_buff. Indeed if we dump the socket state at the time
of the warning the sk_error_queue is often (but not always)
corrupted. The ->next pointer points back at the list head,
but not the ->prev pointer. Indeed we can find the leaked skb
by scanning the kernel memory for something that looks like
an skb with ->sk = socket in question, and ->truesize = 0x300.
The contents of ->cb[] of the skb confirms the suspicion that
it is indeed a timestamp notification (as generated in
__skb_complete_tx_timestamp()).
Removing purging of sk_error_queue should be okay, since
inet_sock_destruct() does it again once all socket refs
are gone. Eric suggests this may cause sockets that go
thru disconnect() to maintain notifications from the
previous incarnations of the socket, but that should be
okay since the race was there anyway, and disconnect()
is not exactly dependable.
Thanks to Jonathan Lemon and Omar Sandoval for help at various
stages of tracing the issue.
Fixes: cb9eff097831 ("net: new user space API for time stamping of incoming and outgoing packets") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
The msm_gem_new_impl() function cleans up after itself so there is no
need to call drm_gem_object_put(). Conceptually, it does not make sense
to call a kref_put() function until after the reference counting has
been initialized which happens immediately after this call in the
drm_gem_(private_)object_init() functions.
In the msm_gem_import() function the "obj" pointer is uninitialized, so
it will lead to a crash.
Fixes: 05b849111c07 ("drm/msm: prime support") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/20211013081315.GG6010@kili Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
The "msm_obj->node" list needs to be initialized earlier so that the
list_del() in msm_gem_free_object() doesn't experience a NULL pointer
dereference.
Fixes: 6ed0897cd800 ("drm/msm: Fix debugfs deadlock") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/20211013081133.GF6010@kili Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Add a missing unlock on the error path if drm_sched_entity_init() fails.
Fixes: 68002469e571 ("drm/msm: One sched entity per process per priority") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/20211011124005.GE15188@kili Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
There are two problems here:
1) The "seqptr" is used uninitalized when we free it at the end.
2) The a6xx_gmu_get_mmio() function returns error pointers. It never
returns true.
Fixes: 64245fc55172 ("drm/msm/a6xx: use AOP-initialized PDC for a650") Fixes: f8fc924e088e ("drm/msm/a6xx: Fix PDC register overlap") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20211004134530.GB11689@kili Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
The DSI host might be left in some state by the bootloader. If this
state generates an IRQ, it might hang the system by holding the
interrupt line before the driver sets up the DSI host to the known
state.
Move the request_irq into msm_dsi_host_init and pass IRQF_NO_AUTOEN to
it. Call enable/disable_irq after msm_dsi_host_power_on/_off()
functions, so that we can be sure that the interrupt is delivered when
the host is in the known state.
It is not possible to defer the interrupt enablement to a later point,
because drm_panel_prepare might need to communicate with the panel over
the DSI link and that requires working interrupt.
Fixes: a689554ba6ed ("drm/msm: Initial add DSI connector support") Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org> Link: https://lore.kernel.org/r/20211002010830.647416-1-dmitry.baryshkov@linaro.org Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
When device_register() return failed, program will goto out_kfree_type
to release 'cdev->device' by put_device(). That will call thermal_release()
to free 'cdev'. But the follow-up processes access 'cdev' continually.
That trggers the UAF bug.
Do not use 'cdev' again after put_device() to fix the problem like doing
in thermal_zone_device_register().
[dlezcano]: as requested by Rafael, change the affectation into two statements.
Fixes: 584837618100 ("thermal/drivers/core: Use a char pointer for the cooling device name") Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Reported-by: kernel test robot <lkp@intel.com> Link: https://lore.kernel.org/r/20211015024504.947520-1-william.xuanziyang@huawei.com Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Currently, in case of aead fallback, no associated data info is set in the
fallback request. To fix this, call aead_request_set_ad() to pass the assoclen.
Fixes: 6f03f0e8b6c8 ("crypto: octeontx2 - register with linux crypto framework") Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Use of percpu_counter structure to track count of orphaned
sockets is causing problems on modern hosts with 256 cpus
or more.
Stefan Bach reported a serious spinlock contention in real workloads,
that I was able to reproduce with a netfilter rule dropping
incoming FIN packets.
As explained in commit cf86a086a180 ("net/dst: use a smaller percpu_counter
batch for dst entries accounting"), default batch size is too big
for the default value of tcp_max_orphans (262144).
But even if we reduce batch sizes, there would still be cases
where the estimated count of orphans is beyond the limit,
and where tcp_too_many_orphans() has to call the expensive
percpu_counter_sum_positive().
One solution is to use plain per-cpu counters, and have
a timer to periodically refresh this cache.
Updating this cache every 100ms seems about right, tcp pressure
state is not radically changing over shorter periods.
percpu_counter was nice 15 years ago while hosts had less
than 16 cpus, not anymore by current standards.
v2: Fix the build issue for CONFIG_CRYPTO_DEV_CHELSIO_TLS=m,
reported by kernel test robot <lkp@intel.com>
Remove unused socket argument from tcp_too_many_orphans()
Fixes: dd24c00191d5 ("net: Use a percpu_counter for orphan_count") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Stefan Bach <sfb@google.com> Cc: Neal Cardwell <ncardwell@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>