[media] mb86a20s: Be sure that device is initialized before starting DVB
Due to a hard to track bug between tda829x/tda18271/saa7134, tda829x
wants to go to analog mode during DVB initialization, causing some
I2C errors.
The analog failure doesn't cause any harm, as the device were already
properly initialized in analog mode. However, the failure at the digital
mode causes the frontend mb86a20s to not initialize. Fortunately, at
least on my tests, it was possible to detect that the device is a
mb86a20s before the failure.
What happens is that tda8290 is a very bad boy: during DVB setup, it
keeps insisting to call tda18271 analog_set_params, that calls
tune_agc code. The tune_agc code calls saa7134 driver, changing the
value of GPIO 27, switching from digital to analog mode and disabling
the access to mb86a20s, as, on Kworld SBTVD, the same GPIO used
to switch the hardware AGC mode seems to be used to enable the I2C
switch that allows access to the frontend (mb86a20s).
So, a call to analog_set_params ultimately disables the access to
the frontend, and causes a failure at the init frontend logic.
This patch is a workaround for this issue: it simply checks if the
frontend init had any failure. If so, it will init the frontend when
some DTV application will try to set DVB mode.
Even being a hack for Kworld SBTVD to work, and assumning that we could
teach tda8290 to be a good boy, this is actually an improvement at the
frontend driver, as it will be more reliable to initialization failures.
This happens because some I2C callbacks actually depend on having the
driver entirely initialized. To avoid this OOPS, just clean the I2C
callbacks, as if no device were detected.
Cc: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are a few bugs at the code that generates the scancode at dib0700:
- RC keycode is wrong (it outputs a 24 bits keycode);
- NEC extended outputs a keycode that have endiannes issues;
- keycode tables for NEC extended remotes need to be updated.
The last issue need to be done as we get reports, as we don't have
the complete NEC-extended keycodes at the dibcom table.
Hans Verkuil [Sat, 8 Jan 2011 12:53:32 +0000 (09:53 -0300)]
[media] v4l2-ioctl: fix incorrect error code if VIDIOC_DBG_G/S_REGISTER are unsupported
The ioctls VIDIOC_DBG_S_REGISTER and VIDIOC_DBG_G_REGISTER should return -EINVAL
if the driver didn't implement them. Currently they return -EPERM if called as
non-root user. However, this check should only be done if the driver actually
implemented these ioctls. Otherwise, just return -EINVAL as we do with all
unimplemented ioctls.
This bug make the v4l2-compliance test suite fail.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Thu, 6 Jan 2011 18:23:55 +0000 (15:23 -0300)]
[media] gspca_sonixj: Probe sensor type independent of bridge type
Looking at the windows inf file, for usb ids with a sensor type where probing
is needed to determine the type (for example ov7630 or soi768), this is
needed for all bridge variants with a usb id indicating this sensor type.
So do the probing to determine the actual sensor type for types where the
usb-id info is not 100% deterministic, independent of the bridge type.
If you look through the list of currently active usb ids in sonixj, this
effectively only changes the code path for 0c45:60fe (sn9c105 + ov7630) and
0c45:612e (sn9c110 + ov7630), which according to the inf file can have a
soi768 instead of a ov7630 just like the sn9c120 + ov7630 models where we
already probe for a soi7630.
The main reason for this code change is to keep the code paths as bridge
variant independent as possible, so that we don't need a lot of special
per bridge cases, as we enable more usb-ids in the future.
This change makes the 0c45:60fe code path identical to the successfully
tested 0c45:613e, so also make sonixj the default driver for 0c45:60fe.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Thu, 6 Jan 2011 16:05:29 +0000 (13:05 -0300)]
[media] gspca_sonixj: Enable more usb ids when sn9c102 gets compiled too
Both we and the windows driver make no sensor specific differences
(with some exceptions) for different sonixj bridge types. Thus if a
sn9c105 bridge has been successfully tested with a sensor, the same
sensor can be successfully used with a sn9c120 bridge too.
Using this knowledge we can move over most usb-ids too the sonixj
driver when both are compiled.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Thu, 6 Jan 2011 14:56:30 +0000 (11:56 -0300)]
[media] gspca_sonixb: Add usb ids for known sn9c103 cameras
Now that our bridge code is unified for sn9c101/102 and sn9c103 models,
the sn9c103 models should simply work, given that the only difference
in the sn9c103 is audio support and a gamma correction table.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Wed, 5 Jan 2011 16:55:43 +0000 (13:55 -0300)]
[media] gspca_sonixb: Refactor to unify bridge handling
Refactor the code to unify how the sn9c101/102 and the sn9c103 bridge
are handled. Also move code which is the same for all sensors from
the per sensor init register settings to a central place.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Wed, 5 Jan 2011 14:36:54 +0000 (11:36 -0300)]
[media] sn9c102: Remove not supported and non existing usb ids
The sn9c102 driver claims a number of usb-ids which are for cameras
with sensor types which it does not support. Also it claims a number
of usb-ids which do not exist at all (not present in the windows
drivers .inf files, not known by google).
This patch also fixes the conflict with the gspca_sonixj driver for the
0c45:60c0 and 0c45:60fb usb ids.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Mon, 3 Jan 2011 15:48:10 +0000 (12:48 -0300)]
[media] et61x251: remove wrongly claimed usb ids
The et61x251 driver claims a whole list of usb id's, but it only has
one sensor "module" which does sensor detection based on usb id and that
only supports devices with the 102c:6251 usb id. Remove the usb-ids for
other devices as for those the driver will fail with an unable to determine
sensor type message anyways.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Fri, 31 Dec 2010 08:05:56 +0000 (05:05 -0300)]
[media] gspca_main: Simplify read mode memory type checks
gspca_dev->memory == GSPCA_MEMORY_NO implies gspca_dev->nframes == 0,
so there is no need to check for both in dev_poll. The check in
dev_read also is more complex then needed, as dqbuf which dev_read
calls already does all necessary checks. Moreover dqbuf is holding
the proper locks while checking where as dev_read itself is not.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Fri, 31 Dec 2010 07:51:36 +0000 (04:51 -0300)]
[media] gspca_main: Set memory type to GSPCA_MEMORY_NO on buffer release
Before this patch we were not setting the memory type to GSPCA_MEMORY_NO
when the buffers were released by the app doing a reqbufs 0. Nor would
the memory type be set to GSPCA_MEMORY_NO on device close, as capture_file
already is NULL on device close because of the reqbufs 0. This caused the
following problem:
-app1 does reqbufs USERPTR for 4 buffers
-app1 does reqbufs USERPTR for 0 buffers
-app2 tries to do reqbufs MMAP for 4 buffers
fails because gspca_dev->memory still is USERPTR
Fixing this also allows an app to switch memory type's by unrequesting
the buffers and re-requesting them of a different type.
This patch also moves the setting of gspca_dev->frsz and gscpa_dev->memory
to after alloc_frame succeeding, so that they are not changed when allocating
fails.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Thu, 30 Dec 2010 23:00:17 +0000 (20:00 -0300)]
[media] gspca_main: Update buffer flags even when user_copy fails
Before this patch dqbuf errors out on a failing user_copy (with user pointers)
before updating the buffer flags, causing a successsfully dequeued buffer
to still have the DONE flag, which means that it could no longer be
re-queueud (assuming the app somehow survives the segfault).
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Thu, 30 Dec 2010 22:54:33 +0000 (19:54 -0300)]
[media] gspca_main: Locking fixes 2
Before this patch vidioc_dqbuf is using its own read_lock, where as
other queue related functions use queue_lock. This means that dqbuf is
accessing several variables in a racy manor. The most important one
being fr_o, which may be changed from underneath dqbuf by vidioc_reqbufs
or vidioc_streamoff. Other variables which it accesses unprotected
are gspca_dev->memory, gspca_dev->streaming and gspca_dev->capt_file.
This patch fixes this by changing vidioc_dqbuf to also use the queue_lock.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Thu, 30 Dec 2010 16:11:21 +0000 (13:11 -0300)]
[media] gspca_main: Locking fixes 1
The gspca_dev->streaming boolean is protected against multiple access
through gspca_dev->queue_lock everywhere except for 2 places. This patch
fixes this by bringing it under the lock in vidioc_streamoff. And by
removing the check for gspca_dev->streaming in gspca_disconnect,
the destroy_urbs call may be called multiple times (and is protected
by the usb_lock) and calling wake_up_interruptible can also always be done
safely.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Antti Palosaari [Sat, 8 Jan 2011 00:59:11 +0000 (21:59 -0300)]
[media] af9013: fix AF9013 TDA18271 IF config
IF freq for DVB-T 7 MHz and 8 MHz was set slightly wrong. Due to that it
didn't worked at all (?) for 7 MHz channels and most likely performance
was dropped for 8 MHz channels.
That bug was pointed by few people during last two months. Thank you.
Trivial fix. Compile tested only due to lack of proper HW and signal.
Hans Verkuil [Wed, 5 Jan 2011 17:42:41 +0000 (14:42 -0300)]
[media] radio-gemtek-pci: remove duplicate driver
The radio-gemtek-pci driver is for the same hardware as the radio-maxiradio
driver which uses the same GemTek PR103 and tea5757 combination and the two
drivers are identical. I chose the maxiradio over the gemtek-pci driver since
the maxiradio has support for mono/stereo detection.
Tested with my gemtek-pci card.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mats Randgaard [Thu, 16 Dec 2010 15:17:43 +0000 (12:17 -0300)]
[media] vpif_cap/disp: Add support for DV presets
- Added functions to set/get/query/enum DV presets for vpif_caputre and
vpif_display.
- The format specification table is extended with all the DV formats
supported by TVP7002.
Mats Randgaard [Thu, 16 Dec 2010 15:17:42 +0000 (12:17 -0300)]
[media] vpif: Consolidate formats from capture and display
- The ch_params tables in vpif_capture.c and vpif_display.c are moved to a common
table in vpif.c. Then it is easier to maintain the table.
- The field "fps" is removed from the struct vpif_channel_config_params because it
is not used.
If there are out-of-tree users of this driver, then they can switch to tvaudio
instead.
The original commit message read as follows:
This change allows bttv to use tvaudio for this device. Since this device
has the same i2c address as the tda9874 we need to support both in the same
tvaudio driver. This makes it possible for tvaudio to detect which chip is
used. Originally the tda9875 was only available in the dedicated tda9875
driver, but that makes life very hard for bttv since loading tvaudio might
misdetect a tda9875 as a tda9874.
So there were good reasons for moving the tda9875 code into tvaudio.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Linus Torvalds [Tue, 18 Jan 2011 22:29:37 +0000 (14:29 -0800)]
Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf: Validate cpu early in perf_event_alloc()
perf: Find_get_context: fix the per-cpu-counter check
perf: Fix contexted inheritance
Linus Torvalds [Tue, 18 Jan 2011 22:29:21 +0000 (14:29 -0800)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Clear irqstack thread_info
x86: Make relocatable kernel work with new binutils
Linus Torvalds [Tue, 18 Jan 2011 22:28:48 +0000 (14:28 -0800)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus: (26 commits)
MIPS: Malta: enable Cirrus FB console
MIPS: add CONFIG_VIRTUALIZATION for virtio support
MIPS: Implement __read_mostly
MIPS: ath79: add common WMAC device for AR913X based boards
MIPS: ath79: Add initial support for the Atheros AP81 reference board
MIPS: ath79: add common SPI controller device
SPI: Add SPI controller driver for the Atheros AR71XX/AR724X/AR913X SoCs
MIPS: ath79: add common GPIO buttons device
MIPS: ath79: add common watchdog device
MIPS: ath79: add common GPIO LEDs device
MIPS: ath79: add initial support for the Atheros PB44 reference board
MIPS: ath79: utilize the MIPS multi-machine support
MIPS: ath79: add GPIOLIB support
MIPS: Add initial support for the Atheros AR71XX/AR724X/AR931X SoCs
MIPS: jump label: Add MIPS support.
MIPS: Use WARN() in uasm for better diagnostics.
MIPS: Optimize TLB handlers for Octeon CPUs
MIPS: Add LDX and LWX instructions to uasm.
MIPS: Use BBIT instructions in TLB handlers
MIPS: Declare uasm bbit0 and bbit1 functions.
...
Oleg Nesterov [Tue, 18 Jan 2011 16:10:08 +0000 (17:10 +0100)]
perf: Find_get_context: fix the per-cpu-counter check
If task == NULL, find_get_context() should always check that cpu
is correct.
Afaics, the bug was introduced by 38a81da2 "perf events: Clean
up pid passing", but even before that commit "&& cpu != -1" was
not exactly right, -ESRCH from find_task_by_vpid() is not
accurate.
Signed-off-by: Oleg Nesterov <oleg@redhat.com> Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Paul Mackerras <paulus@samba.org> Cc: Prasad <prasad@linux.vnet.ibm.com> Cc: Roland McGrath <roland@redhat.com> Cc: gregkh@suse.de Cc: stable@kernel.org
LKML-Reference: <20110118161008.GB693@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Aurelien Jarno [Tue, 18 Jan 2011 11:20:45 +0000 (12:20 +0100)]
MIPS: Malta: enable Cirrus FB console
While most users of a physical Malta board are using the serial port
as the console, a lot of QEMU users would prefer to interact with a
graphical console. Enable the Cirrus FB support in the Malta default
configuration to make that possible. Note that the default console will
still be the serial port, users have to pass "console=tty0" to the
kernel to use the Cirrus FB.
David Daney [Thu, 14 Oct 2010 19:36:49 +0000 (12:36 -0700)]
MIPS: Implement __read_mostly
Just do what everyone else is doing by placing __read_mostly things in
the .data.read_mostly section.
mips_io_port_base can not be read-only (const) and writable
(__read_mostly) at the same time. One of them has to go, so I chose
to eliminate the __read_mostly. It will still get stuck in a portion
of memory that is not adjacent to things that are written, and thus
not be on a dirty cache line, for whatever that is worth.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1702/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Gabor Juhos [Tue, 4 Jan 2011 20:28:29 +0000 (21:28 +0100)]
MIPS: ath79: add common WMAC device for AR913X based boards
Add common platform_device and helper code to make the registration
of the built-in wireless MAC easier on the Atheros AR9130/AR9132
based boards. Also register the WMAC device on the AR81 board.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Cc: linux-mips@linux-mips.org Cc: Imre Kaloz <kaloz@openwrt.org>, Cc: Luis R. Rodriguez <lrodriguez@atheros.com> Cc: Cliff Holden <Cliff.Holden@Atheros.com> Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1962/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Gabor Juhos [Tue, 4 Jan 2011 20:28:23 +0000 (21:28 +0100)]
MIPS: ath79: add common SPI controller device
Several boards are using the built-in SPI controller of the
AR71XX/AR724X/AR913X SoCs. This patch adds common platform_device
and helper code to register it. Additionally, the patch registers
the SPI bus on the PB44 board.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Cc: linux-mips@linux-mips.org Cc: Imre Kaloz <kaloz@openwrt.org> Cc: Luis R. Rodriguez <lrodriguez@atheros.com> Cc: Cliff Holden <Cliff.Holden@Atheros.com> Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1956/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The current patch contains minimal support only, but the resulting
kernel can boot into user-space with using of an initramfs image on
various boards which are using these SoCs. Support for more built-in
devices and individual boards will be implemented in further patches.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: Imre Kaloz <kaloz@openwrt.org> Cc: linux-mips@linux-mips.org Cc: Luis R. Rodriguez <lrodriguez@atheros.com> Cc: Cliff Holden <Cliff.Holden@Atheros.com> Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1947/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Tue, 28 Dec 2010 21:26:23 +0000 (13:26 -0800)]
MIPS: jump label: Add MIPS support.
In order not to be left behind, we add jump label support for MIPS.
Tested on 64-bit big endian (Octeon), and 32-bit little endian
(malta/qemu).
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Jason Baron <jbaron@redhat.com>
Patchwork: https://patchwork.linux-mips.org/patch/1923/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Tue, 28 Dec 2010 02:18:29 +0000 (18:18 -0800)]
MIPS: Use WARN() in uasm for better diagnostics.
On the off chance that uasm ever warns about overflow, there is no way
to know what the offending instruction is.
Change the printks to WARNs, so we can get a nice stack trace. It has
the added benefit of being much more noticeable than the short single
line warning message, so is less likely to be ignored.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1905/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Mon, 20 Dec 2010 23:54:50 +0000 (15:54 -0800)]
MIPS: Use BBIT instructions in TLB handlers
If the CPU supports BBIT0 and BBIT1, use them in TLB handlers as they
are more efficient than an AND followed by an branch and then
restoring the clobbered register.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1873/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Gabor Juhos [Tue, 23 Nov 2010 15:06:25 +0000 (16:06 +0100)]
MIPS: Add generic support for multiple machines within a single kernel
This patch adds a generic solution to support multiple machines based on
a given SoC within a single kernel image. It is implemented already for
several other architectures but MIPS has no generic support for that yet.
[Ralf: This competes with DT but DT is a much more complex solution and this
code has been used by OpenWRT for a long time so for now DT is a bad reason
to stop the merge but longer term this should be migrated to DT.]
Linus Torvalds [Tue, 18 Jan 2011 16:05:50 +0000 (08:05 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Fix initialization for HP 2011 notebooks
ALSA: hda - Add support for VMware controller
ALSA: hda - consitify string arrays
ALSA: hda - Add add multi-streaming playback for AD1988
ASoC: EP93xx: fixed LRCLK rate and DMA oper. in I2S code
ASoC: WM8990: msleep() takes milliseconds not jiffies
ALSA : au88x0 - Limit number of channels to fix Oops via OSS emu
ALSA: constify functions in ac97
ASoC: WL1273 FM radio: Fix breakage with MFD API changes
ALSA: hda - More coverage for odd-number channels elimination for HDMI
ALSA: hda - Store PCM parameters properly in HDMI open callback
ALSA: hda - Rearrange fixup struct in patch_realtek.c
ALSA: oxygen: Xonar DG: fix CS4245 register writes
ALSA: hda - Suppress the odd number of channels for HDMI
ALSA: hda - Add fixup-call in init callback
ALSA: hda - Reorganize fixup structure for Realtek
ALSA: hda - Apply Sony VAIO hweq fixup only once
ALSA: hda - Apply mario fixup only once
ALSA: hda - Remove unused fixup entry for ALC262
Linus Torvalds [Tue, 18 Jan 2011 16:05:20 +0000 (08:05 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu: (25 commits)
m68knommu: fix broken setting of irq_chip and handler
m68knommu: switch to using -mcpu= flags for ColdFire targets
m68knommu: arch/m68knommu/Kconfig whitespace cleanup
m68knommu: create optimal separate instruction and data cache for ColdFire
m68knommu: support ColdFire caches that do copyback and write-through
m68knommu: support version 2 ColdFire split cache
m68knommu: make cache push code ColdFire generic
m68knommu: clean up ColdFire cache control code
m68knommu: move inclusion of ColdFire v4 cache registers
m68knommu: merge bit definitions for version 3 ColdFire cache controller
m68knommu: create bit definitions for the version 2 ColdFire cache controller
m68knommu: remove empty __iounmap() it is no used
m68knommu: remove kernel_map() code, it is not used
m68knommu: remove do_page_fault(), it is not used
m68knommu: use user stack pointer hardware on some ColdFire cores
m68knommu: remove command line printing DEBUG
m68knommu: remove fasthandler interrupt code
m68knommu: move UART addressing to part specific includes
m68knommu: fix clock rate value reported for ColdFire 54xx parts
m68knommu: move ColdFire CPU names into their headers
...
Linus Torvalds [Tue, 18 Jan 2011 16:04:30 +0000 (08:04 -0800)]
Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf tools: Fix tracepoint id to string perf.data header table
perf tools: Fix handling of wildcards in tracepoint event selectors
powerpc: perf: Fix frequency calculation for overflowing counters
Linus Torvalds [Tue, 18 Jan 2011 15:58:36 +0000 (07:58 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
autofs4: clean ->d_release() and autofs4_free_ino() up
autofs4: split autofs4_init_ino()
autofs4: mkdir and symlink always get a dentry that had passed lookup
autofs4: autofs4_get_inode() doesn't need autofs_info * argument anymore
autofs4: kill ->size in autofs_info
autofs4: pass mode to autofs4_get_inode() explicitly
autofs4: autofs4_mkroot() is not different from autofs4_init_ino()
autofs4: keep symlink body in inode->i_private
autofs4 - fix debug print in autofs4_lookup()
vfs - fix dentry ref count in do_lookup()
autofs4 - fix get_next_positive_dentry()
Shaohua Li [Tue, 18 Jan 2011 00:57:49 +0000 (08:57 +0800)]
x86: Make relocatable kernel work with new binutils
The CONFIG_RELOCATABLE=y option is broken with new binutils, which will make
boot panic.
According to Lu Hongjiu, the affected binutils are from 2.20.51.0.12 to
2.21.51.0.3, which are release since Oct 22 this year. At least ubuntu 10.10 is
using such binutils. See:
The reason of the boot panic is that we have 'jiffies = jiffies_64;' in
vmlinux.lds.S. The jiffies isn't in any section. In kernel build, there is
warning saying jiffies is an absolute address and can't be relocatable. At
runtime, jiffies will have virtual address 0.
Signed-off-by: Shaohua Li<shaohua.li@intel.com> Cc: Lu Hongjiu<hongjiu.lu@intel.com> Cc: Huang Ying <ying.huang@intel.com> Cc: Sam Ravnborg <sam@ravnborg.org>
LKML-Reference: <1295312269.1949.725.camel@sli10-conroe> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Raymond Yau [Mon, 17 Jan 2011 10:19:03 +0000 (11:19 +0100)]
ALSA: hda - Add add multi-streaming playback for AD1988
Attached a patch which add a new model to support multi-streaming
playback for ad1988.
playback another stereo stream through the front panel headphone on
device 2 while playback through the speakers connected to rear panel
on device 0 at the same time.
Tested with ad1988a rev2 codec on asus P5B-V motherboard.
Signed-off-by: Raymond Yau <superquad.vortex2@gmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Al Viro [Sun, 16 Jan 2011 23:43:40 +0000 (18:43 -0500)]
autofs4: split autofs4_init_ino()
split init_ino into new_ino and clean_ino; the former is
what used to be init_ino(NULL, sbi), the latter is for cases
where we passed non-NULL ino. Lose unused arguments.
Acked-by: Ian Kent <raven@themaw.net> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
projects / mirror_ubuntu-zesty-kernel.git / log