Dave Airlie [Mon, 7 Dec 2009 03:29:51 +0000 (13:29 +1000)]
drm/radeon/kms: fix RS600 MC setup.
Again we try to put VRAM at 0, and it didn't work on this chipset,
reports of corrupt RAM appeared on irc and bugzilla.
Fix the vram location according to what the BIOS setup, I'm not 100%
sure we don't need the same thing on rs690/rs780/rs880, we probably
should do it there just in case as its what the DDX does.
Jerome Glisse [Fri, 20 Nov 2009 13:29:23 +0000 (14:29 +0100)]
drm/radeon/kms: Rework radeon object handling
The locking & protection of radeon object was somewhat messy.
This patch completely rework it to now use ttm reserve as a
protection for the radeon object structure member. It also
shrink down the various radeon object structure by removing
field which were redondant with the ttm information. Last it
converts few simple functions to inline which should with
performances.
airlied: rebase on top of r600 and other changes.
Signed-off-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Tue, 1 Dec 2009 06:04:56 +0000 (16:04 +1000)]
drm/radeon/kms: add irq mitigation code for sw interrupt.
We really don't need to process every irq that comes in, we only
really want to do SW irq processing when we are actually waiting for
a fence to pass. I'm not 100% sure this is race free esp on non-MSI systems
so it needs some testing.
Alex Deucher [Tue, 1 Dec 2009 18:43:46 +0000 (13:43 -0500)]
drm/radeon/kms: Add support for interrupts on r6xx/r7xx chips (v3)
This enables the use of interrupts on r6xx/r7xx hardware.
Interrupts are implemented via a ring buffer. The GPU adds
interrupts vectors to the ring and the host reads them off
in the interrupt handler. The interrupt controller requires
firmware like the CP. This firmware must be installed and
accessble to the firmware loader for interrupts to function.
MSIs don't seem to work on my RS780. They work fine on all
my discrete cards. I'm not sure about other RS780s or
RS880s. I've disabled MSIs on RS780 and RS880, but it would
probably be worth checking on some other systems.
v2 - fix some checkpatch.pl problems;
re-read the disp int status reg if we restart the ih;
v3 - remove the irq handler if r600_irq_init() fails;
remove spinlock in r600_ih_ring_fini();
move ih rb overflow check to r600_get_ih_wptr();
move irq ack to separate function;
Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Jerome Glisse [Thu, 26 Nov 2009 14:58:36 +0000 (15:58 +0100)]
drm/radeon/kms: Don't overwrite crtc_gen_cntl or crtc_gen_cntl2
Don't overwritte crtc_gen_cntl or crtc_gen_cntl2 or we may loose the
cursor. This especialy happen when changing video mode. Fix bugs:
https://bugzilla.redhat.com/show_bug.cgi?id=529146
Signed-off-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Jerome Glisse [Mon, 30 Nov 2009 16:47:59 +0000 (17:47 +0100)]
drm/radeon/kms: Disable agp only if we are dealing with an AGP GPU
On IGP if you pass option agpmode=-1 you would overwrite the set_page
function callback with improper function which endup in non functioning
hw. This patch will disable agp when giving agpmode=-1 parameter only
if we are dealing with an AGP GPU.
Signed-off-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Pierre Ossman [Mon, 30 Nov 2009 20:15:44 +0000 (21:15 +0100)]
drm/radeon/kms: Disable both CRTCs during mode switch
Reconfiguring one CRTC whilst another is running can cause a hang under
some circumstances. Unfortunately we haven't pinpointed exactly what those
circumstances are, so disable all CRTCs for every mode switch.
Signed-off-by: Pierre Ossman <pierre@ossman.eu> Acked-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher [Mon, 30 Nov 2009 06:54:16 +0000 (01:54 -0500)]
drm/radeon/kms: fix LVDS setup on r4xx
R4xx mobility chips use atombios, which does not store
the LVDS_GEN_CNTL parameter setup like combios. Rather,
it's configured in LVDSEncoderControl. As such,
LVDS_GEN_CNTL is set wrong when on resume. Call
LVDSEncoderControl to set it properly.
Should fix fdo bug 25336
Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher [Tue, 17 Nov 2009 20:44:01 +0000 (15:44 -0500)]
drm/radeon/kms: deal with connectors sourced to the same encoder
Some systems have multiple connectors connected to the same encoder;
e.g., DVI and HDMI connected to the same encoder with the same ddc
line. Since we expose connectors as xrandr outputs, randr treats them
separately which results in it trying to source the same encoder to
different crtcs. If we have an HDMI and DVI-D port on the same encoder,
pick the one to be considered connected based on the edid (HDMI if edid
indicates HDMI, DVI otherwise).
Should fix fdo bug 25150
Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher [Thu, 12 Nov 2009 19:55:14 +0000 (14:55 -0500)]
drm/radeon/kms: rework scaler handling
Keep requested scaler type in radeon_encoder
and the actual scaler type used in radeon_crtc.
This prevents us from enabling the scaler when it's
not required (i.e., the requested mode is the native
mode). Also, always set the adjusted mode equal
to the native mode for lvds.
Should fix:
https://bugzilla.redhat.com/show_bug.cgi?id=522271
Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Acked-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher [Wed, 11 Nov 2009 02:25:07 +0000 (21:25 -0500)]
drm/radeon/kms: add support for external tmds on legacy boards
This enables initialization of external tmds chips on pre-atom
and mac systems. Macs are untested. Also, some macs have single
link tmds chips while others have dual link tmds chips. We need
to figure out which ones have which.
This gets external TMDS working on my RS485 and RV380.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: Add support for Mobilcom Debitel USB UMTS Surf-Stick to option driver
USB: work around for EHCI with quirky periodic schedules
USB: musb: Fix CPPI IRQs not being signaled
USB: musb: respect usb_request->zero in control requests
USB: musb: fix ISOC Tx programming for CPPI DMAs
USB: musb: Remove unwanted message in boot log
usb: amd5536udc: fixed shared interrupt bug and warning oops
USB: ftdi_sio: Keep going when write errors are encountered.
USB: musb_gadget: fix STALL handling
USB: EHCI: don't send Clear-TT-Buffer following a STALL
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
tty/of_serial: add missing ns16550a id
bcm63xx_uart: Fix serial driver compile breakage.
tty_port: handle the nonblocking open of a dead port corner case
Linus Torvalds [Tue, 1 Dec 2009 16:26:44 +0000 (08:26 -0800)]
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
MIPS: Loongson: Switch from flatmem to sparsemem
MIPS: Loongson: Disallow 4kB pages
MIPS: Add missing definition for MADV_HWPOISON.
MIPS: Fix build error if __xchg() is not getting inlined.
MIPS: IP22/IP28 Disable early printk to fix boot problems on some systems.
Wu Zhangjin [Tue, 1 Dec 2009 06:55:25 +0000 (14:55 +0800)]
MIPS: Loongson: Disallow 4kB pages
Currently, with PAGE_SIZE_4KB, the kernel for loongson will hang on:
Kernel panic - not syncing: Attempted to kill init!
The possible reason is the cache aliases problem:
Loongson 2F has 64kb, 4 way L1 Cache, the way size is 16kb, which is bigger
then 4kb. so, If using 4kb page size, there is cache aliases problem.
To avoid this kind of problem, extra cache flushing. The 2nd possible
solution is 16kb page size which avoids cache aliases without the need for
extra cache flushes. So we disable 4kB pages until the aliasing issue is
solved.
Ralf Baechle [Tue, 24 Nov 2009 13:16:02 +0000 (13:16 +0000)]
MIPS: Fix build error if __xchg() is not getting inlined.
If __xchg() is not getting inlined the outline version of the function
will have a reference to __xchg_called_with_bad_pointer() which does not
exist remaining. Fixed by using BUILD_BUG_ON() to check for allowable
operand sizes.
Martin Michlmayr [Thu, 19 Nov 2009 16:40:09 +0000 (16:40 +0000)]
MIPS: IP22/IP28 Disable early printk to fix boot problems on some systems.
Some Debian users have reported that the kernel hangs early during boot on
some IP22 systems. Thomas Bogendoerfer found that this is due to a "bad
interaction between CONFIG_EARLY_PRINTK and overwritten prom memory during
early boot". Since there's no fix yet, disable CONFIG_EARLY_PRINTK for now.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com> Cc: linux-mips@linux-mips.org Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/702/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Linus Torvalds [Tue, 1 Dec 2009 15:36:23 +0000 (07:36 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha-2.6:
alpha: Fixup last users of irq_chip->typename
Alpha: Rearrange thread info flags fixing two regressions
arch/alpha/kernel: Add kmalloc NULL tests
arch/alpha/kernel/sys_ruffian.c: Use DIV_ROUND_CLOSEST
David Howells [Tue, 1 Dec 2009 13:52:08 +0000 (13:52 +0000)]
SLOW_WORK: Fix the CONFIG_MODULES=n case
Commits 3d7a641 ("SLOW_WORK: Wait for outstanding work items belonging to a
module to clear") introduced some code to make sure that all of a module's
slow-work items were complete before that module was removed, and commit 3bde31a ("SLOW_WORK: Allow a requeueable work item to sleep till the thread is
needed") further extended that, breaking it in the process if CONFIG_MODULES=n:
CC kernel/slow-work.o
kernel/slow-work.c: In function 'slow_work_execute':
kernel/slow-work.c:313: error: 'slow_work_thread_processing' undeclared (first use in this function)
kernel/slow-work.c:313: error: (Each undeclared identifier is reported only once
kernel/slow-work.c:313: error: for each function it appears in.)
kernel/slow-work.c: In function 'slow_work_wait_for_items':
kernel/slow-work.c:950: error: 'slow_work_unreg_sync_lock' undeclared (first use in this function)
kernel/slow-work.c:951: error: 'slow_work_unreg_wq' undeclared (first use in this function)
kernel/slow-work.c:961: error: 'slow_work_unreg_work_item' undeclared (first use in this function)
kernel/slow-work.c:974: error: 'slow_work_unreg_module' undeclared (first use in this function)
kernel/slow-work.c:977: error: 'slow_work_thread_processing' undeclared (first use in this function)
make[1]: *** [kernel/slow-work.o] Error 1
Fix this by:
(1) Extracting the bits of slow_work_execute() that are contingent on
CONFIG_MODULES, and the bits that should be, into inline functions and
placing them into the #ifdef'd section that defines the relevant variables
and adding stubs for moduleless kernels. This allows the removal of some
#ifdefs.
(2) #ifdef'ing out the contents of slow_work_wait_for_items() in moduleless
kernels.
The four functions related to handling module unloading synchronisation (and
their associated variables) could be offloaded into a separate .c file, but
each function is only used once and three of them are tiny, so doing so would
prevent them from being inlined.
David Howells [Tue, 1 Dec 2009 13:38:45 +0000 (13:38 +0000)]
9p: fix build breakage introduced by FS-Cache
While building 2.6.32-rc8-git2 for Fedora I noticed the following thinko
in commit 201a15428bd54f83eccec8b7c64a04b8f9431204 ("FS-Cache: Handle
pages pending storage that get evicted under OOM conditions"):
fs/9p/cache.c: In function '__v9fs_fscache_release_page':
fs/9p/cache.c:346: error: 'vnode' undeclared (first use in this function)
fs/9p/cache.c:346: error: (Each undeclared identifier is reported only once
fs/9p/cache.c:346: error: for each function it appears in.)
make[2]: *** [fs/9p/cache.o] Error 1
Fix the 9P filesystem to correctly construct the argument to
fscache_maybe_release_page().
Thomas Gleixner [Tue, 1 Dec 2009 03:51:31 +0000 (22:51 -0500)]
alpha: Fixup last users of irq_chip->typename
The typename member of struct irq_chip was kept for migration purposes
and is obsolete since more than 2 years. Fix up the leftovers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Richard Henderson <rth@twiddle.net> Cc: linux-alpha@vger.kernel.org Signed-off-by: Matt Turner <mattst88@gmail.com>
Michael Cree [Tue, 1 Dec 2009 03:44:40 +0000 (22:44 -0500)]
Alpha: Rearrange thread info flags fixing two regressions
The removal of the TIF_NOTIFY_RESUME flag, commit a583f1b54249b
"remove unused TIF_NOTIFY_RESUME flag," resulted in incorrect
setting of the unaligned access control flags by the prctl syscall.
The re-addition of the TIF_NOTIFY_RESUME flag, commit d0420c83f39f
"KEYS: Extend TIF_NOTIFY_RESUME to (almost) all architectures [try #6]"
further caused problems, namely incorrect operands to assembler code
as evidenced by:
AS arch/alpha/kernel/entry.o
arch/alpha/kernel/entry.S: Assembler messages:
arch/alpha/kernel/entry.S:326: Warning: operand out of range
(0x0000000000000406 is not between 0x0000000000000000 and
0x00000000000000ff)
Both regressions fixed by (1) rearranging TIF_NOTIFY_RESUME flag to be
in lower 8 bits of the thread info flags, and (2) making sure that
ALPHA_UAC_SHIFT matches the rearrangement of the thread info flags.
Signed-off-by: Michael Cree <mcree@orcon.net.nz> Cc: Richard Henderson <rth@twiddle.net> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Cc: David Howells <dhowells@redhat.com>, Signed-off-by: Matt Turner <mattst88@gmail.com>
Gernot Hillier [Fri, 27 Nov 2009 12:49:23 +0000 (13:49 +0100)]
USB: Add support for Mobilcom Debitel USB UMTS Surf-Stick to option driver
This patch adds the vendor and device id for the Mobilcom Debitel UMTS surf
stick (a.k.a. 4G Systems XSStick W14, MobiData MBD-200HU, ...).
To see these ids, you need to switch the stick to modem operation first
with the help of usb_modeswitch. This makes it switch from 1c9e:f000 to
1c9e:9603 and thus be recognized by the option driver.
Oliver Neukum [Fri, 27 Nov 2009 14:17:59 +0000 (15:17 +0100)]
USB: work around for EHCI with quirky periodic schedules
a quirky chipset needs periodic schedules to run for a minimum
time before they can be disabled again. This enforces the requirement
with a time stamp and a calculated delay
Daniel Glöckner [Tue, 17 Nov 2009 09:52:57 +0000 (15:22 +0530)]
USB: musb: Fix CPPI IRQs not being signaled
On tx channel abort a cppi interrupt is generated for a short time by
setting the lowest bit of the TCPPICOMPPTR register. It is then reset
immediately by clearing the bit. When the interrupt handler is run,
it does not detect an interrupt in the TCPPIMSKSR or RCPPIMSKSR
registers and thus exits early without writing the TCPPIEOIR register.
It appears that this inhibits further cppi interrupts until the handler
is called by chance, f.ex. from davinci_interrupt().
By moving the unmasking of the interrupt below the writes to
TCPPICOMPPTR, no interrupt is generated and no write to TCPPIEOIR is
necessary.
Daniel Glöckner [Tue, 17 Nov 2009 09:52:56 +0000 (15:22 +0530)]
USB: musb: respect usb_request->zero in control requests
In gadget mode the answer to a control request should be followed by
a zero-length packet if the amount transferred is an exact multiple of
the endpoint's packet size and the requests has its "zero" flag set.
This patch prevents the request from being immediately removed from the
queue when a control IN transfer ends on a full packet and "zero" is set.
The next time ep0_txstate is entered, a zero-length packet is queued and
the request is removed as fifo_count is 0.
Thomas Dahlmann [Tue, 17 Nov 2009 22:18:27 +0000 (14:18 -0800)]
usb: amd5536udc: fixed shared interrupt bug and warning oops
- fixed shared interrupt bug reported by Vadim Lobanov
- fixed possible warning oops on driver unload when connected
- prevent interrupt flood in PIO mode ("modprobe amd5536udc use_dma=0")
when using gadget ether
Signed-off-by: Thomas Dahlmann <dahlmann.thomas@arcor.de> Cc: Robert Richter <robert.richter@amd.com> Cc: David Brownell <david-b@pacbell.net> Cc: stable <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: ftdi_sio: Keep going when write errors are encountered.
The use of urb->actual_length to update tx_outstanding_bytes
implicitly assumes that the number of bytes actually written is the
same as the number of bytes we tried to write. On error that
assumption is violated so just use transfer_buffer_length the number
of bytes we intended to write to the device.
If an error occurs we need to fall through and call
usb_serial_port_softint to wake up processes waiting in
tty_wait_until_sent.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sergei Shtylyov [Wed, 18 Nov 2009 19:51:18 +0000 (22:51 +0300)]
USB: musb_gadget: fix STALL handling
The driver incorrectly cancels the mass-storage device CSW request
(which leads to device reset) due to giving back URB at the head of
endpoint's queue after sending each STALL handshake; stop doing that
and start checking for the queue being non-empty before stalling an
endpoint and disallowing stall in such case in musb_gadget_set_halt()
like the other gadget drivers do.
Moreover, the driver starts Rx request despite of the endpoint being
halted -- fix this by moving the SendStall bit check from musb_g_rx()
to rxstate(). And we also sometimes get into rxstate() with DMA still
active after clearing an endpoint's halt (not clear why), so bail out
in this case, similarly to what txstate() does...
While at it, also do the following changes :
- in musb_gadget_set_halt(), remove pointless Tx FIFO flushing (the
driver does not allow stalling with non-empty Tx FIFO anyway);
- in rxstate(), stop pointlessly zeroing the 'csr' variable;
- in musb_gadget_set_halt(), move the 'done' label to a more proper
place;
- in musb_g_rx(), eliminate the 'done' label completely...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Wed, 18 Nov 2009 16:37:15 +0000 (11:37 -0500)]
USB: EHCI: don't send Clear-TT-Buffer following a STALL
This patch (as1304) fixes a regression in ehci-hcd. Evidently some
hubs don't handle Clear-TT-Buffer requests correctly, so we should
avoid sending them when they don't appear to be absolutely necessary.
The reported symptom is that output on a downstream audio device cuts
out because the hub stops relaying isochronous packets.
The patch prevents Clear-TT-Buffer requests from being sent following
a STALL handshake. In theory a STALL indicates either that the
downstream device sent a STALL or that no matching TT buffer could be
found. In either case, the transfer is completed and the TT buffer
does not remain busy, so it doesn't need to be cleared.
Also, the patch fixes a minor flaw in the code that actually sends the
Clear-TT-Buffer requests. Although the pipe direction isn't really
used for control transfers, it should be a Send rather than a Receive.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Javier Kohen <jkohen@users.sourceforge.net> CC: David Brownell <david-b@pacbell.net> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Haiyang Zhang [Fri, 20 Nov 2009 16:29:17 +0000 (16:29 +0000)]
Staging: hv: Fix vmbus event handler bug
The flag ENABLE_POLLING is always enabled in original Makefile, but
accidently removed during porting to mainline kernel. The patch fixes
this bug which can cause stalled network communication. Credit needs to
go to Eric Sesterhenn <eric.sesterhenn@lsexperts.de> For pointing out a
typo in the original code as well.
Michal Simek [Tue, 24 Nov 2009 10:22:41 +0000 (10:22 +0000)]
tty/of_serial: add missing ns16550a id
Many boards have a bug-free ns16550 compatible serial port, which we should
register as PORT_16550A. This introduces a new value "ns16550a" for the
compatible property of of_serial to let a firmware choose that model instead
of using the crippled PORT_16550 mode.
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: gcm - fix another complete call in complete fuction
crypto: padlock-aes - Use the correct mask when checking whether copying is required
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
[CIFS] Fix sparse warning
[CIFS] Duplicate data on appending to some Samba servers
[CIFS] fix oops in cifs_lookup during net boot
Linus Torvalds [Mon, 30 Nov 2009 22:50:44 +0000 (14:50 -0800)]
Merge branch 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
at24: Use timeout also for read
i2c: Fix userspace_device list corruption
MAINTAINERS: Add missing i2c files
i2c/tsl2550: Fix lux value in extended mode
Linus Torvalds [Mon, 30 Nov 2009 22:50:01 +0000 (14:50 -0800)]
Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] Update mach-types
ARM: 5793/1: ARM: Check put_user fail in do_signal when enable OABI_COMPAT
MAINTAINERS: add maintainer information for AMBA primecell drivers
[ARM] pxa/spitz: fix compile regression on spitz
ARM: PNX4008: i2c-pnx: use the same dev_id for request_irq and free_irq
[ARM] pxa/cpufreq: fix index assignments for end marker
ARM: PNX4008: fix watchdog device driver name
[ARM] kmap: fix build errors with DEBUG_HIGHMEM enabled
Becky Bruce [Mon, 23 Nov 2009 12:28:53 +0000 (12:28 +0000)]
powerpc: Fix DEBUG_HIGHMEM build break from d4515646699
Code was added to mm/higmem.c that depends on several
kmap types that powerpc does not support. We add dummy
invalid definitions for KM_NMI, KM_NM_PTE, and KM_IRQ_PTE.
According to list discussion, this fix should not be needed
anymore starting with 2.6.33. The code is commented to this
effect so hopefully we will remember to remove this.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sunsu: Use sunserial_console_termios() in sunsu_console_setup().
sunsu: Pass true 'ignore_line' to console match when RSC or LOM console.
serial: suncore: Fix RSC/LOM handling in sunserial_console_termios().
serial: suncore: Add 'ignore_line' argument to sunserial_console_match().
sunsu: Fix detection of SU ports which are RSC console or control.
sunsab: Do not set sunsab_reg.cons right before registering minors.
sparc64: Fix definition of VMEMMAP_SIZE.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (42 commits)
b44: Fix wedge when using netconsole.
wan: cosa: drop chan->wsem on error path
ep93xx-eth: check for zero MAC address on probe, not on device open
NET: smc91x: Fix irq flags
smsc9420: prevent BUG() if ethtool is called with interface down
r8169: restore mac addr in rtl8169_remove_one and rtl_shutdown
ipv4: additional update of dev_net(dev) to struct *net in ip_fragment.c, NULL ptr OOPS
e100: Use pci pool to work around GFP_ATOMIC order 5 memory allocation failure
sctp: on T3_RTX retransmit all the in-flight chunks
pktgen: Fix netdevice unregister
macvlan: fix gso_max_size setting
rfkill: fix miscdev ops
ath9k: set ps_default as false
hso: fix soft-lockup
hso: fix debug routines
pktgen: Fix device name compares
stmmac: do not fail when the timer cannot be used.
stmmac: fixed a compilation error when use the external timer
netfilter: xt_limit: fix invalid return code in limit_mt_check()
Au1x00: fix crash when trying register_netdev()
...
Linus Torvalds [Mon, 30 Nov 2009 21:58:23 +0000 (13:58 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: ohci: pass correct iso xmit timestamps to core
firewire: ohci: Make cycleMatch ISO transmission work
Linus Torvalds [Mon, 30 Nov 2009 21:57:03 +0000 (13:57 -0800)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
cciss: make device attrs static
Thaw refrigerated bdi flusher threads before invoking kthread_stop on them
Linus Torvalds [Mon, 30 Nov 2009 21:56:21 +0000 (13:56 -0800)]
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
acerhdf: return temperature in milidegree instead of degree
thinkpad-acpi: fix detection of old ThinkPads
thinkpad-acpi: fix sign of ERESTARTSYS return
ACPI: Add Thinkpad T400, T500 to OSI(Linux) white-list
ACPICA: Silence the warning about _BIF returning the buffer
ACPI: DMI init_set_sci_en_on_resume for HP-Compaq C700
Linus Torvalds [Mon, 30 Nov 2009 21:54:10 +0000 (13:54 -0800)]
Merge branch 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/fb: fix FBIOGET/PUT_VSCREENINFO pixel clock handling
drm: make sure page protections are updated after changing vm_flags
drm/radeon/kms: Report vga connector is connected according to ddc_probe
drm: mm always protect change to unused_nodes with unused_lock spinlock
drm/radeon/kms: Disable TV load detect on RS400,RC410,RS480
drm/radeon/kms: read back register before writing in IIO.
drm/radeon/kms: fix handling of d1/d2 vga
drm: work around EDIDs with bad htotal/vtotal values
drm/radeon/kms: resume AGP by calling init.
Linus Torvalds [Mon, 30 Nov 2009 21:53:14 +0000 (13:53 -0800)]
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
Staging: octeon-ethernet: Assign proper MAC addresses.
Staging: Octeon: Use symbolic values for irq numbers.
MIPS: Octeon: Fix compile error in drivers/staging/octeon/ethernet-mdio.c
David Woodhouse [Mon, 30 Nov 2009 09:06:40 +0000 (09:06 +0000)]
jffs2: Fix memory corruption in jffs2_read_inode_range()
In 2.6.23 kernel, commit a32ea1e1f925399e0d81ca3f7394a44a6dafa12c
("Fix read/truncate race") fixed a race in the generic code, and as a
side effect, now do_generic_file_read() can ask us to readpage() past
the i_size. This seems to be correctly handled by the block routines
(e.g. block_read_full_page() fills the page with zeroes in case if
somebody is trying to read past the last inode's block).
JFFS2 doesn't handle this; it assumes that it won't be asked to read
pages which don't exist -- and thus that there will be at least _one_
valid 'frag' on the page it's being asked to read. It will fill any
holes with the following memset:
When the 'closest smaller match' returned by jffs2_lookup_node_frag() is
actually on a previous page and ends before 'offset', that results in:
memset(buf, 0, <huge unsigned negative>);
Hopefully, in most cases the corruption is fatal, and quickly causing
random oopses, like this:
root@10.0.0.4:~/ltp-fs-20090531# ./testcases/kernel/fs/ftest/ftest01
Unable to handle kernel paging request for data at address 0x00000008
Faulting instruction address: 0xc01cd980
Oops: Kernel access of bad area, sig: 11 [#1]
[...]
NIP [c01cd980] rb_insert_color+0x38/0x184
LR [c0043978] enqueue_hrtimer+0x88/0xc4
Call Trace:
[c6c63b60] [c004f9a8] tick_sched_timer+0xa0/0xe4 (unreliable)
[c6c63b80] [c0043978] enqueue_hrtimer+0x88/0xc4
[c6c63b90] [c0043a48] __run_hrtimer+0x94/0xbc
[c6c63bb0] [c0044628] hrtimer_interrupt+0x140/0x2b8
[c6c63c10] [c000f8e8] timer_interrupt+0x13c/0x254
[c6c63c30] [c001352c] ret_from_except+0x0/0x14
--- Exception: 901 at memset+0x38/0x5c
LR = jffs2_read_inode_range+0x144/0x17c
[c6c63cf0] [00000000] (null) (unreliable)
This patch fixes the issue, plus fixes all LTP tests on NAND/UBI with
JFFS2 filesystem that were failing since 2.6.23 (seems like the bug
above also broke the truncation).
Reported-By: Anton Vorontsov <avorontsov@ru.mvista.com> Tested-By: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Cc: stable@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / mirror_ubuntu-bionic-kernel.git / log