Miri Korenblit [Tue, 28 Mar 2023 07:58:55 +0000 (10:58 +0300)]
wifi: iwlwifi: mvm: align to the LINK cmd update in the FW
The LINK cmd host api has been updated. Align the driver to the
new changes. Also, temporary use mac_id for link_id.
Using the phy_id as the link_id is wrong since we might have 2 macs
operating on the same phy - in this case we will have 2 different
links (one for each mac) with the same link_id. On the other hand,
since we don't have MLO implemented yet, we won't have 2 different
links of the same mac. Therefore, we can use the mac_id as the
link_id.
Miri Korenblit [Tue, 28 Mar 2023 07:58:54 +0000 (10:58 +0300)]
wifi: iwlwifi: mvm: always use the sta->addr as the peers addr
Currently we're setting the sta->addr as the peers address only if
the iftype is NL80211_IFTYPE_AP, otherwise we are setting the bssid to
be the addr. This causes bugs in TDLS. Fix this by always using the
sta->addr.
Miri Korenblit [Tue, 28 Mar 2023 07:58:53 +0000 (10:58 +0300)]
wifi: iwlwifi: mvm: modify link instead of removing it during csa
During CSA the PHY used by the link is changing, So the driver
needs to modify the links phy to the FW. Currently the driver is doing
it by removing the link and adding a new one with the new phy_id, but the
FW expects the link only to be modified. Fix this by modifying the links
phy_id instead of removing it and adding a new one
Miri Korenblit [Tue, 28 Mar 2023 07:58:51 +0000 (10:58 +0300)]
wifi: iwlwifi: mvm: fix "modify_mask" value in the link cmd.
This bitmap indicates what fields of the cmd got changed.
A field will be ignored by the FW if the corresponding flag wasn't set.
There are a few cases in which we currently set the wrong bits when
sending this cmd, which caused FW asserts. Fix this by setting the
correct bits in each case.
Miri Korenblit [Tue, 28 Mar 2023 07:58:48 +0000 (10:58 +0300)]
wifi: iwlwifi: mvm: unite sta_modify_disable_tx flows
These flows are the same in both MLD API and the current API,
except for the commands that are being sent during this flows.
Instead of checking each time before calling these floews
what API we use and then call the correct function, call always the old
one, which in turn will call the new one in case we're using the MLD
API.
Miri Korenblit [Tue, 28 Mar 2023 07:58:46 +0000 (10:58 +0300)]
wifi: iwlwifi: mvm: refactor iwl_mvm_roc()
This flow is almost the same for both MLD and non-MLD modes,
except for some function calls. Therefore there is no reason to
add an MLD version of this flow. Instead - put the parts that are unique
for each mode in helper functions, and in the next patch each version of
this flow will call the common part with pointers to its specific
helper functions.
Miri Korenblit [Tue, 28 Mar 2023 07:58:44 +0000 (10:58 +0300)]
wifi: iwlwifi: mvm: add sta handling flows for MLD mode
In MLD mode we have a new STA cmd. As a result, it is also changes
the flows of adding/updating/removing and handling state of
a station. Add these flows.
Miri Korenblit [Tue, 28 Mar 2023 07:58:43 +0000 (10:58 +0300)]
wifi: iwlwifi: mvm: add an indication that the new MLD API is used
WE can't mix between the new MLD API and the old API.
I.e. - we can't send one of the new cmds and then one of the old ones.
This will cause a FW assert. So we need an indication what API should be
used. We use the new API if:
1. FW supports it
2. We are registered to mac80211 with the new MLD ops
Add an indication which will only be true if both conditions are true.
Gregory Greenman [Tue, 28 Mar 2023 07:58:41 +0000 (10:58 +0300)]
wifi: iwlwifi: mvm: vif preparation for MLO
In MLO, some fields of iwl_mvm_vif should be defined in the
context of a link. Define a separate structure for these fields and
add a deflink object to hold it as part of iwl_mvm_vif. Non-MLO legacy
code will use only deflink object while MLO related code will use the
corresponding link from the link array.
It follows the strategy applied in mac80211 for introducing MLO
changes.
The below spatch takes care of updating all driver code to access
fields separated into MLD specific data structure via deflink (need
to convert all references to the fields listed in var to deflink.var
and also to take care of calls like iwl_mvm_vif_from_mac80211(vif)->field).
clang with W=1 reports
net/mac80211/rc80211_minstrel_ht.c:1711:6: error: variable
'n_supported' set but not used [-Werror,-Wunused-but-set-variable]
int n_supported = 0;
^
This variable is not used so remove it.
wifi: iwlwifi: mvm: Use 64-bit division helper in iwl_mvm_get_crosstimestamp_fw()
There is a 64-bit division in iwl_mvm_get_crosstimestamp_fw(), which
results in a link failure when building 32-bit architectures with clang:
ld.lld: error: undefined symbol: __udivdi3
>>> referenced by ptp.c
>>> drivers/net/wireless/intel/iwlwifi/mvm/ptp.o:(iwl_mvm_phc_get_crosstimestamp) in archive vmlinux.a
GCC has optimizations for division by a constant that clang does not
implement, so this issue is not visible when building with GCC.
Use the 64-bit division helper div_u64(), which takes a u64 dividend and
u32 divisor, which matches this situation and prevents the emission of a
libcall for the division.
Jaewan Kim [Wed, 22 Mar 2023 13:16:37 +0000 (13:16 +0000)]
mac80211_hwsim: add PMSR report support via virtio
PMSR (a.k.a. peer measurement) is generalized measurement between two
devices with Wi-Fi support. And currently FTM (a.k.a. fine time measurement
or flight time measurement) is the one and only measurement.
Add the necessary functionality to allow mac80211_hwsim to report PMSR
result. The result would come from the wmediumd, where other Wi-Fi
devices' information are kept. mac80211_hwsim only need to deliver the
result to the userspace.
In detail, add new mac80211_hwsim attributes HWSIM_CMD_REPORT_PMSR, and
HWSIM_ATTR_PMSR_RESULT. When mac80211_hwsim receives the PMSR result with
command HWSIM_CMD_REPORT_PMSR and detail with attribute
HWSIM_ATTR_PMSR_RESULT, received data is parsed to cfg80211_pmsr_result and
resent to the userspace by cfg80211_pmsr_report().
To help receive the details of PMSR result, hwsim_rate_info_attributes is
added to receive rate_info without complex bitrate calculation. (i.e. send
rate_info without adding inverse of nl80211_put_sta_rate()).
Jaewan Kim [Wed, 22 Mar 2023 13:16:36 +0000 (13:16 +0000)]
mac80211_hwsim: add PMSR abort support via virtio
PMSR (a.k.a. peer measurement) is generalized measurement between two
devices with Wi-Fi support. And currently FTM (a.k.a. fine time
measurement or flight time measurement) is the one and only measurement.
Add necessary functionalities for mac80211_hwsim to abort previous PMSR
request. The abortion request is sent to the wmedium where the PMSR request
is actually handled.
In detail, add new mac80211_hwsim command HWSIM_CMD_ABORT_PMSR. When
mac80211_hwsim receives the PMSR abortion request via
ieee80211_ops.abort_pmsr, the received cfg80211_pmsr_request is resent to
the wmediumd with command HWSIM_CMD_ABORT_PMSR and attribute
HWSIM_ATTR_PMSR_REQUEST. The attribute is formatted as the same way as
nl80211_pmsr_start() expects.
Jaewan Kim [Wed, 22 Mar 2023 13:16:35 +0000 (13:16 +0000)]
mac80211_hwsim: add PMSR request support via virtio
PMSR (a.k.a. peer measurement) is generalized measurement between two
Wi-Fi devices. And currently FTM (a.k.a. fine time measurement or flight
time measurement) is the one and only measurement. FTM is measured by
RTT (a.k.a. round trip time) of packets between two Wi-Fi devices.
Add necessary functionalities for mac80211_hwsim to start PMSR request by
passthrough the request to wmediumd via virtio. mac80211_hwsim can't
measure RTT for real because mac80211_hwsim the software simulator and
packets are sent almost immediately for real. This change expect wmediumd
to have all the location information of devices, so passthrough requests
to wmediumd.
In detail, add new mac80211_hwsim command HWSIM_CMD_ABORT_PMSR. When
mac80211_hwsim receives the PMSR start request via
ieee80211_ops.start_pmsr, the received cfg80211_pmsr_request is resent to
the wmediumd with command HWSIM_CMD_START_PMSR and attribute
HWSIM_ATTR_PMSR_REQUEST. The attribute is formatted as the same way as
nl80211_pmsr_start() expects.
Jaewan Kim [Wed, 22 Mar 2023 13:16:33 +0000 (13:16 +0000)]
mac80211_hwsim: add PMSR capability support
PMSR (a.k.a. peer measurement) is generalized measurement between two
Wi-Fi devices. And currently FTM (a.k.a. fine time measurement or flight
time measurement) is the one and only measurement. FTM is measured by
RTT (a.k.a. round trip time) of packets between two Wi-Fi devices.
Add necessary functionality to allow mac80211_hwsim to be configured with
PMSR capability. The capability is mandatory to accept incoming PMSR
request because nl80211_pmsr_start() ignores incoming the request without
the PMSR capability.
In detail, add new mac80211_hwsim attribute HWSIM_ATTR_PMSR_SUPPORT.
HWSIM_ATTR_PMSR_SUPPORT is used to set PMSR capability when creating a new
radio. To send extra capability details, HWSIM_ATTR_PMSR_SUPPORT can have
nested PMSR capability attributes defined in the nl80211.h. Data format is
the same as cfg80211_pmsr_capabilities.
If HWSIM_ATTR_PMSR_SUPPORT is specified, mac80211_hwsim builds
cfg80211_pmsr_capabilities and sets wiphy.pmsr_capa.
Aloka Dixit [Thu, 23 Mar 2023 11:38:01 +0000 (04:38 -0700)]
mac80211: support RNR for EMA AP
Generate EMA beacons, each including MBSSID and RNR elements at a given
index. If number of stored RNR elements is more than the number of
MBSSID elements then add those in every EMA beacon.
Aloka Dixit [Thu, 23 Mar 2023 11:38:00 +0000 (04:38 -0700)]
cfg80211: support RNR for EMA AP
As per IEEE Std 802.11ax-2021, 11.1.3.8.3 Discovery of a nontransmitted
BSSID profile, an EMA AP that transmits a Beacon frame carrying a partial
list of nontransmitted BSSID profiles should include in the frame
a Reduced Neighbor Report element carrying information for at least the
nontransmitted BSSIDs that are not present in the Multiple BSSID element
carried in that frame.
Add new nested attribute NL80211_ATTR_EMA_RNR_ELEMS to support the above.
Number of RNR elements must be more than or equal to the number of
MBSSID elements. This attribute can be used only when EMA is enabled.
Userspace is responsible for splitting the RNR into multiple elements such
that each element excludes the non-transmitting profiles already included
in the MBSSID element (%NL80211_ATTR_MBSSID_ELEMS) at the same index.
Each EMA beacon will be generated by adding MBSSID and RNR elements
at the same index. If the userspace provides more RNR elements than the
number of MBSSID elements then these will be added in every EMA beacon.
Bagas Sanjaya [Thu, 23 Mar 2023 09:24:54 +0000 (16:24 +0700)]
wifi: mac80211: use bullet list for amsdu_mesh_control formats list
Commit fe4a6d2db3ba ("wifi: mac80211: implement support for yet
another mesh A-MSDU format") expands amsdu_mesh_control list to
multi-line list. However, the expansion triggers Sphinx warning:
Link: https://lore.kernel.org/linux-next/20230323141548.659479ef@canb.auug.org.au/ Fixes: fe4a6d2db3bad4 ("wifi: mac80211: implement support for yet another mesh A-MSDU format") Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Aloka Dixit [Tue, 6 Dec 2022 00:50:37 +0000 (16:50 -0800)]
wifi: mac80211: generate EMA beacons in AP mode
Add APIs to generate an array of beacons for an EMA AP (enhanced
multiple BSSID advertisements), each including a single MBSSID element.
EMA profile periodicity equals the count of elements.
- ieee80211_beacon_get_template_ema_list() - Generate and return all
EMA beacon templates. Drivers must call ieee80211_beacon_free_ema_list()
to free the memory. No change in the prototype for the existing API,
ieee80211_beacon_get_template(), which should be used for non-EMA AP.
- ieee80211_beacon_get_template_ema_index() - Generate a beacon which
includes the multiple BSSID element at the given index. Drivers can use
this function in a loop until NULL is returned which indicates end of
available MBSSID elements.
- ieee80211_beacon_free_ema_list() - free the memory allocated for the
list of EMA beacon templates.
Modify existing functions ieee80211_beacon_get_ap(),
ieee80211_get_mbssid_beacon_len() and ieee80211_beacon_add_mbssid()
to accept a new parameter for EMA index.
wifi: nl80211: Update the documentation of NL80211_SCAN_FLAG_COLOCATED_6GHZ
Currently when NL80211_SCAN_FLAG_COLOCATED_6GHZ is set in the scan flags,
in addition to the co-located APs, PSC channels in the 6 GHz band would
also be scanned if the user space has asked for it. In other words, the
scan would happen on PSC channels & co-located 6 GHz channels that were
reported in the RNR IE.
Update the documentation of NL80211_SCAN_FLAG_COLOCATED_6GHZ flag to
reflect the above said behavior.
Felix Fietkau [Tue, 14 Mar 2023 09:59:53 +0000 (10:59 +0100)]
wifi: mac80211: mesh fast xmit support
Previously, fast xmit only worked on interface types where initially a
sta lookup is performed, and a cached header can be attached to the sta,
requiring only some fields to be updated at runtime.
This technique is not directly applicable for a mesh device type due
to the dynamic nature of the topology and protocol. There are more
addresses that need to be filled, and there is an extra header with a
dynamic length based on the addressing mode.
Change the code to cache entries contain a copy of the mesh subframe header +
bridge tunnel header, as well as an embedded struct ieee80211_fast_tx, which
contains the information for building the 802.11 header.
Add a mesh specific early fast xmit call, which looks up a cached entry and
adds only the mesh subframe header, before passing it over to the generic
fast xmit code.
To ensure the changes in network are reflected in these cached headers,
flush affected cached entries on path changes, as well as other conditions
that currently trigger a fast xmit check in other modes (key changes etc.)
This code is loosely based on a previous implementation by:
Sriram R <quic_srirrama@quicinc.com>
Cc: Sriram R <quic_srirrama@quicinc.com> Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Link: https://lore.kernel.org/r/20230314095956.62085-4-nbd@nbd.name Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix Fietkau [Tue, 21 Mar 2023 09:12:48 +0000 (10:12 +0100)]
wifi: mac80211: add support for letting drivers register tc offload support
On newer MediaTek SoCs (e.g. MT7986), WLAN->WLAN or WLAN->Ethernet flows can
be offloaded by the SoC. In order to support that, the .ndo_setup_tc op is
needed.
Avraham Stern [Mon, 20 Mar 2023 10:33:18 +0000 (12:33 +0200)]
wifi: iwlwifi: mvm: support enabling and disabling HW timestamping
Instead of enabling HW timestamping by default every time a station
is connected, disable it by default and enable it only upon request
for a specific station. HW timestamping can be enabled for only one
peer at a time.
As we have a new MLD STA cmd, there will be a different function to
add/remove a station in MLD mode. But both functions will share a
common part. Put this part in a separate function which will be used
later in adding/removing a sta in MLD mode.
Miri Korenblit [Mon, 20 Mar 2023 10:33:15 +0000 (12:33 +0200)]
wifi: iwlwifi: mvm: remove not needed initializations
In iwl_mvm_add_sta() we're initializing the new allocated mvm_sta.
We are setting some fields to zero even though it was allocated with
kzalloc, for the case of HW restart. But in such a case we will never
get to this initializations due to the goto statement that we have in
this case. Remove these initializations.
We have a new STA cmd as part of the new MLD API. There are some
parts of sending the STA cmd which are common to both the old and
the new one. Put this parts in functions which will later be used
to send the new STA cmd.
Miri Korenblit [Mon, 20 Mar 2023 10:33:13 +0000 (12:33 +0200)]
wifi: iwlwifi: mvm: refactor iwl_mvm_sta
As the new MLD API is introduced, we have a new enumeration
for the different station types. Since struct iwl_mvm_sta's
sta_type field will be in use for both new and old API,
change its type to a unified one, so it can hold both.
Miri Korenblit [Mon, 20 Mar 2023 10:33:12 +0000 (12:33 +0200)]
wifi: iwlwifi: mvm: refactor iwl_mvm_cfg_he_sta()
This function sends the STA_HE_CTXT_CMD, which won't be used in the
new MLD API. Instead, a part of the fields of this command
will be in the new STA cmd. Put the parts that are common to both
commands in functions, which will later be used in sending the new
STA cmd.
Miri Korenblit [Mon, 20 Mar 2023 10:33:11 +0000 (12:33 +0200)]
wifi: iwlwifi: mvm: Don't send MAC CTXT cmd after deauthorization
We used to send a MAC CTXT cmd to ask the FW to not pass MCAST frames
if we're associated but not authorized, because we don't have the
keys in that stage, and after authorization - we sent the cmd again
to ask the FW to pass MCAST, as we have the keys now.
The patch linked below was changing this strategy to always allow
MCAST frames, and if we're not authorized - the driver will drop them.
But we're still sending the MAC CTXT cmd after deaouthorization even
though we don't tell the FW to not pass MCAST frames anymore.
Basically we don't tell the FW anything new with this cmd.
Fix this by not sending MAC CTXT command after deauthorization.
For authorization we're sending the cmd to configure other changes too,
so keep it.
Avraham Stern [Mon, 20 Mar 2023 10:33:08 +0000 (12:33 +0200)]
wifi: iwlwifi: mvm: select ptp cross timestamp from multiple reads
iwl_mvm_get_sync_time() reads the gp2 from the device and then
reads the system clock. Since the two reads are not done atomically,
unexpected delays may happen between the two reads (e.g. context
switch) which make it inaccurate.
In order to improve the accuracy of the cross timestamp, call
iwl_mvm_get_sync_time() multiple times in a loop and take the
result in which the difference between the two clock is the smallest.
Implement the following PHC operations:
1. adjtime - for adding an offset to the PHC clock time.
2. adjfine - for adjusting the PHC clock frequency.
3. gettime64 - for getting the PHC clock time. This function returns
the time as adjusted by adjtime and adjfine.
The adjusted time will also be used for time sync frames timestamping.
Avraham Stern [Mon, 20 Mar 2023 10:33:04 +0000 (12:33 +0200)]
wifi: iwlwifi: mvm: report hardware timestamps in RX/TX status
For TM/FTM frames, report the hardware timestamps reported by the
fw as part of the RX/TX status. Since the fw reports the timestamps
in a dedicated notification (and not as part of the RX/TX status),
hold the frame until the fw timestamps notification is received.
Timestamping is enabled when a station is connected and disabled
when disconnected. For AP interface, only the first station will
have timestamping enabled since the fw only supports timestamping
for one peer.
Avraham Stern [Mon, 20 Mar 2023 10:33:03 +0000 (12:33 +0200)]
wifi: iwlwifi: mvm: read synced time from firmware if supported
If the firmware supports reading synced GP2/ATRB timestamps,
read the synced timestamps from firmware instead of reading the
GP2 register and the system time separately. Reading the synced
time from firmware should be more accurate.
wifi: iwlwifi: mvm: add support for PTP HW clock (PHC)
Add support to enable/disable PHC clock. The PHC clock includes support
for fetching the cross timestamp i.e. a non-atomic snapshot of the current
time from the hardware (WiFi device) clock and system clock (wall-clock)
simultaneously.
Bitterblue Smith [Mon, 13 Mar 2023 13:58:14 +0000 (15:58 +0200)]
wifi: rtl8xxxu: Support new chip RTL8710BU aka RTL8188GU
This chip is found in cheap "free driver" USB adapters from Aliexpress.
Initially they pretend to be a CD-ROM containing the driver for Windows.
"Ejecting" switches the device to wifi mode.
Features: 2.4 GHz, b/g/n mode, 1T1R, 150 Mbps.
This chip is more unique than other Realtek chips:
* The registers at addresses 0x0-0xff, which all the other chips use,
can't be used here. New registers at 0x8000-0x80ff must be used
instead. And it's not a simple matter of adding 0x8000: 0x2
(REG_SYS_FUNC) became 0x8004, 0x80 (REG_MCU_FW_DL) became 0x8090,
etc.
* Also there are a few new registers which must be accessed indirectly
because their addresses don't fit in 16 bits. No other chips seem to
have these.
* The vendor driver compiles to 8188gu.ko, but the code calls the chip
RTL8710B(U) pretty much everywhere, including messages visible to the
user.
Another difference compared to the other chips supported by rtl8xxxu is
that it has a new PHY status struct, or three of them actually, from
which we extract the RSSI, among other things. This is not unique,
though, just new. The chips supported by rtw88 also use it.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com> Reviewed-by: Ping-Ke Shih <pkshih@realtek.com> Tested-by: Philipp Hortmann <philipp.g.hortmann@gmail.com> # Edimax N150 Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/4edbe29f-00b9-8eef-9789-20bed0b141e2@gmail.com
The warning being disabled by this pragma is GCC specific. Guard its use
with CONFIG_CC_IS_GCC so that it is not used with clang to clear up the
error.
Johannes Berg [Wed, 15 Mar 2023 12:29:20 +0000 (13:29 +0100)]
wifi: iwlwifi: suppress printf warnings in tracing
This can't really be fixed due to the macro layout of
tracepoints (you'd need a special tracepoint macro for
when this is needed), so just suppress the warnings.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Tue, 14 Mar 2023 17:49:34 +0000 (19:49 +0200)]
wifi: iwlwifi: fw: pnvm: fix uefi reduced TX power loading
There are a number of issues here:
* if trans->reduce_power_loaded is already true, we call
iwl_trans_set_reduce_power() with an uninitialized len
value
* in this case we also clobber a previous load/setting
* if iwl_uefi_get_reduced_power() returns an ERR_PTR() we
try to kfree() it
Move the iwl_trans_set_reduce_power() call into the success
case only to fix these issues.
Johannes Berg [Tue, 14 Mar 2023 17:49:32 +0000 (19:49 +0200)]
wifi: iwlwifi: mvm: rs: print BAD_RATE for invalid HT/VHT index
If there's a rate->index that maps inside the range but
to an uninitialized value, then that's also a bad rate,
avoid printing "(nil)" in that case and rather print the
"BAD_RATE" string instead as in the else branch.
Tom Rix [Tue, 14 Mar 2023 17:49:27 +0000 (19:49 +0200)]
wifi: iwlwifi: mvm: remove setting of 'sta' parameter
cppcheck reports
[drivers/net/wireless/intel/iwlwifi/mvm/rs.c:2686]: (warning) Assignment of function parameter has no effect outside the function. Did you forget dereferencing it?
The setting of the 'sta' parameter is not needed. In the if-check that sets it
to NULL, mvm_sta is also set to NULL. Then the next statement checks if
mvm_sta is NULL and does an early return. So remove setting sta.
Since parts of the functionality of this function is going to be used
also by the MLD version of it, put in a separate function the parts
that are common for both MLD and non-MLD modes.
The common function will later be used in the MLD ops.
Since parts of the functionality of this function is going to be used
also by the MLD version of it, put in a separate function the parts
that are common for both MLD and non-MLD modes.
The common function will later be used in the MLD ops.
Miri Korenblit [Tue, 14 Mar 2023 17:49:22 +0000 (19:49 +0200)]
wifi: iwlwifi: mvm: Add a remove_interface() callback for mld mode
As the MLD mode and its new APIs are introduced,
we've decided to add a new ieee80211_ops dedicated for
MLD callbacks. Add the MLD remove_interface() callback
which uses the new MLD APIs.
Miri Korenblit [Tue, 14 Mar 2023 17:49:21 +0000 (19:49 +0200)]
wifi: iwlwifi: mvm: Add an add_interface() callback for mld mode
As the MLD mode and its new APIs are introduced,
we've decided to add a new ieee80211_ops dedicated for
MLD callbacks. Add the MLD add_interface() callback
which uses the new MLD APIs added the previous patches.
Miri Korenblit [Tue, 14 Mar 2023 17:49:20 +0000 (19:49 +0200)]
wifi: iwlwifi: mvm: add support for the new STA related commands
As a part of the new MLD FW API changes, we have new commands for STA
related operations (add/remove/aux/disable tx).
Add structures and enum definitions, along with part of the functions
that sends this commands.
This functions will be in used and more will be added in the next patches.
Miri Korenblit [Tue, 14 Mar 2023 17:49:19 +0000 (19:49 +0200)]
wifi: iwlwifi: mvm: add support for the new LINK command
As a part of the new MLD FW API changes, we have a new LINK command
to add/remove/configure a link.
Add structures and enum definitions, along with the functions that
sends this command (i.e. add, remove and change mac ctxt).
These functions will be in used in the next patches.
Miri Korenblit [Tue, 14 Mar 2023 17:49:18 +0000 (19:49 +0200)]
wifi: iwlwifi: mvm: add support for the new MAC CTXT command
As a part of the new MLD FW API changes, we have a new MAC CTXT command.
Add structures and enum definitions, along with the functions that
sends this command (i.e. add, remove and change mac ctxt).
This functions will be in used in the next patches.
1. As the new MLD API is introduced, there are some common fields in
both the old and new APIs. The MAC_CONTEXT_CMD of the non-MLD API
has common fields with the link and mac commands of the new MLD API.
Put this common parts in functions so it can be used later by the
new MLD API.
2. Use iwl_mvm_mac_ctxt_send_cmd when removing a mac instead of
implementing the same functionality once again.
3. Change the debug print when sending the command to be more specific,
so it will be easy to distinguish later if the old or new mac command
was sent.
1. As the new MLD API is introduced, there are some common fields in
both the old and new APIs. The STA_HE_CTXT_CMD of the non-MLD API
has common fields with the link and mac commands of the new MLD API.
Put this common parts in functions so it can be used later by the
new MLD API.
2. The HE capability which indicates whether the NIC is ack-enabled or
not is the same for all bands. No need to take it from the specific
band which is currently in use. Take it from the low band - this
simplifies the code and doesn't require a phy_ctxt.
Johannes Berg [Tue, 14 Mar 2023 17:49:13 +0000 (19:49 +0200)]
wifi: iwlwifi: mvm: avoid sta lookup in queue alloc
In FW restart scenarios, we allocate the queues from the
iwl_mvm_realloc_queues_after_restart() function, but that
is called before we insert the station ID into our map
(mvm->fw_id_to_mac_id).
However, in all cases where we're actually allocating a
queue for a "real" (not bcast, aux, ...) station we have
the sta pointer already, so just pass it along to use it
instead of looking it up.
This fixes an issue where after restart we only allocated
a queue of size 16 (due to the ordering issue described
above), and thus never got good throughput again since no
aggregates could be formed on transmit.
Lukas Bulwahn [Tue, 14 Mar 2023 04:18:48 +0000 (05:18 +0100)]
MAINTAINERS: adjust file entries after wifi driver movement
Commit f79cbc77abde ("wifi: move mac80211_hwsim and virt_wifi to virtual
directory") and commit 298e50ad8eb8 ("wifi: move raycs, wl3501 and
rndis_wlan to legacy directory") move remaining wireless drivers into
subdirectories, but does not adjust the entries in MAINTAINERS.
Hence, ./scripts/get_maintainer.pl --self-test=patterns complains about
broken references.
Repair these file references in those wireless driver sections.
Jisoo Jang [Thu, 9 Mar 2023 10:44:57 +0000 (19:44 +0900)]
wifi: brcmfmac: slab-out-of-bounds read in brcmf_get_assoc_ies()
Fix a slab-out-of-bounds read that occurs in kmemdup() called from
brcmf_get_assoc_ies().
The bug could occur when assoc_info->req_len, data from a URB provided
by a USB device, is bigger than the size of buffer which is defined as
WL_EXTRA_BUF_MAX.
Add the size check for req_len/resp_len of assoc_info.
Found by a modified version of syzkaller.
[ 46.592467][ T7] ==================================================================
[ 46.594687][ T7] BUG: KASAN: slab-out-of-bounds in kmemdup+0x3e/0x50
[ 46.596572][ T7] Read of size 3014656 at addr ffff888019442000 by task kworker/0:1/7
[ 46.598575][ T7]
[ 46.599157][ T7] CPU: 0 PID: 7 Comm: kworker/0:1 Tainted: G O 5.14.0+ #145
[ 46.601333][ T7] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
[ 46.604360][ T7] Workqueue: events brcmf_fweh_event_worker
[ 46.605943][ T7] Call Trace:
[ 46.606584][ T7] dump_stack_lvl+0x8e/0xd1
[ 46.607446][ T7] print_address_description.constprop.0.cold+0x93/0x334
[ 46.608610][ T7] ? kmemdup+0x3e/0x50
[ 46.609341][ T7] kasan_report.cold+0x79/0xd5
[ 46.610151][ T7] ? kmemdup+0x3e/0x50
[ 46.610796][ T7] kasan_check_range+0x14e/0x1b0
[ 46.611691][ T7] memcpy+0x20/0x60
[ 46.612323][ T7] kmemdup+0x3e/0x50
[ 46.612987][ T7] brcmf_get_assoc_ies+0x967/0xf60
[ 46.613904][ T7] ? brcmf_notify_vif_event+0x3d0/0x3d0
[ 46.614831][ T7] ? lock_chain_count+0x20/0x20
[ 46.615683][ T7] ? mark_lock.part.0+0xfc/0x2770
[ 46.616552][ T7] ? lock_chain_count+0x20/0x20
[ 46.617409][ T7] ? mark_lock.part.0+0xfc/0x2770
[ 46.618244][ T7] ? lock_chain_count+0x20/0x20
[ 46.619024][ T7] brcmf_bss_connect_done.constprop.0+0x241/0x2e0
[ 46.620019][ T7] ? brcmf_parse_configure_security.isra.0+0x2a0/0x2a0
[ 46.620818][ T7] ? __lock_acquire+0x181f/0x5790
[ 46.621462][ T7] brcmf_notify_connect_status+0x448/0x1950
[ 46.622134][ T7] ? rcu_read_lock_bh_held+0xb0/0xb0
[ 46.622736][ T7] ? brcmf_cfg80211_join_ibss+0x7b0/0x7b0
[ 46.623390][ T7] ? find_held_lock+0x2d/0x110
[ 46.623962][ T7] ? brcmf_fweh_event_worker+0x19f/0xc60
[ 46.624603][ T7] ? mark_held_locks+0x9f/0xe0
[ 46.625145][ T7] ? lockdep_hardirqs_on_prepare+0x3e0/0x3e0
[ 46.625871][ T7] ? brcmf_cfg80211_join_ibss+0x7b0/0x7b0
[ 46.626545][ T7] brcmf_fweh_call_event_handler.isra.0+0x90/0x100
[ 46.627338][ T7] brcmf_fweh_event_worker+0x557/0xc60
[ 46.627962][ T7] ? brcmf_fweh_call_event_handler.isra.0+0x100/0x100
[ 46.628736][ T7] ? rcu_read_lock_sched_held+0xa1/0xd0
[ 46.629396][ T7] ? rcu_read_lock_bh_held+0xb0/0xb0
[ 46.629970][ T7] ? lockdep_hardirqs_on_prepare+0x273/0x3e0
[ 46.630649][ T7] process_one_work+0x92b/0x1460
[ 46.631205][ T7] ? pwq_dec_nr_in_flight+0x330/0x330
[ 46.631821][ T7] ? rwlock_bug.part.0+0x90/0x90
[ 46.632347][ T7] worker_thread+0x95/0xe00
[ 46.632832][ T7] ? __kthread_parkme+0x115/0x1e0
[ 46.633393][ T7] ? process_one_work+0x1460/0x1460
[ 46.633957][ T7] kthread+0x3a1/0x480
[ 46.634369][ T7] ? set_kthread_struct+0x120/0x120
[ 46.634933][ T7] ret_from_fork+0x1f/0x30
[ 46.635431][ T7]
[ 46.635687][ T7] Allocated by task 7:
[ 46.636151][ T7] kasan_save_stack+0x1b/0x40
[ 46.636628][ T7] __kasan_kmalloc+0x7c/0x90
[ 46.637108][ T7] kmem_cache_alloc_trace+0x19e/0x330
[ 46.637696][ T7] brcmf_cfg80211_attach+0x4a0/0x4040
[ 46.638275][ T7] brcmf_attach+0x389/0xd40
[ 46.638739][ T7] brcmf_usb_probe+0x12de/0x1690
[ 46.639279][ T7] usb_probe_interface+0x2aa/0x760
[ 46.639820][ T7] really_probe+0x205/0xb70
[ 46.640342][ T7] __driver_probe_device+0x311/0x4b0
[ 46.640876][ T7] driver_probe_device+0x4e/0x150
[ 46.641445][ T7] __device_attach_driver+0x1cc/0x2a0
[ 46.642000][ T7] bus_for_each_drv+0x156/0x1d0
[ 46.642543][ T7] __device_attach+0x23f/0x3a0
[ 46.643065][ T7] bus_probe_device+0x1da/0x290
[ 46.643644][ T7] device_add+0xb7b/0x1eb0
[ 46.644130][ T7] usb_set_configuration+0xf59/0x16f0
[ 46.644720][ T7] usb_generic_driver_probe+0x82/0xa0
[ 46.645295][ T7] usb_probe_device+0xbb/0x250
[ 46.645786][ T7] really_probe+0x205/0xb70
[ 46.646258][ T7] __driver_probe_device+0x311/0x4b0
[ 46.646804][ T7] driver_probe_device+0x4e/0x150
[ 46.647387][ T7] __device_attach_driver+0x1cc/0x2a0
[ 46.647926][ T7] bus_for_each_drv+0x156/0x1d0
[ 46.648454][ T7] __device_attach+0x23f/0x3a0
[ 46.648939][ T7] bus_probe_device+0x1da/0x290
[ 46.649478][ T7] device_add+0xb7b/0x1eb0
[ 46.649936][ T7] usb_new_device.cold+0x49c/0x1029
[ 46.650526][ T7] hub_event+0x1c98/0x3950
[ 46.650975][ T7] process_one_work+0x92b/0x1460
[ 46.651535][ T7] worker_thread+0x95/0xe00
[ 46.651991][ T7] kthread+0x3a1/0x480
[ 46.652413][ T7] ret_from_fork+0x1f/0x30
[ 46.652885][ T7]
[ 46.653131][ T7] The buggy address belongs to the object at ffff888019442000
[ 46.653131][ T7] which belongs to the cache kmalloc-2k of size 2048
[ 46.654669][ T7] The buggy address is located 0 bytes inside of
[ 46.654669][ T7] 2048-byte region [ffff888019442000, ffff888019442800)
[ 46.656137][ T7] The buggy address belongs to the page:
[ 46.656720][ T7] page:ffffea0000651000 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x19440
[ 46.657792][ T7] head:ffffea0000651000 order:3 compound_mapcount:0 compound_pincount:0
[ 46.658673][ T7] flags: 0x100000000010200(slab|head|node=0|zone=1)
[ 46.659422][ T7] raw: 01000000000102000000000000000000dead000000000122ffff888100042000
[ 46.660363][ T7] raw: 0000000000000000000000000008000800000001ffffffff0000000000000000
[ 46.661236][ T7] page dumped because: kasan: bad access detected
[ 46.661956][ T7] page_owner tracks the page as allocated
[ 46.662588][ T7] page last allocated via order 3, migratetype Unmovable, gfp_mask 0x52a20(GFP_ATOMIC|__GFP_NOWARN|__GFP_NORETRY|__GFP_COMP), pid 7, ts 31136961085, free_ts 0
[ 46.664271][ T7] prep_new_page+0x1aa/0x240
[ 46.664763][ T7] get_page_from_freelist+0x159a/0x27c0
[ 46.665340][ T7] __alloc_pages+0x2da/0x6a0
[ 46.665847][ T7] alloc_pages+0xec/0x1e0
[ 46.666308][ T7] allocate_slab+0x380/0x4e0
[ 46.666770][ T7] ___slab_alloc+0x5bc/0x940
[ 46.667264][ T7] __slab_alloc+0x6d/0x80
[ 46.667712][ T7] kmem_cache_alloc_trace+0x30a/0x330
[ 46.668299][ T7] brcmf_usbdev_qinit.constprop.0+0x50/0x470
[ 46.668885][ T7] brcmf_usb_probe+0xc97/0x1690
[ 46.669438][ T7] usb_probe_interface+0x2aa/0x760
[ 46.669988][ T7] really_probe+0x205/0xb70
[ 46.670487][ T7] __driver_probe_device+0x311/0x4b0
[ 46.671031][ T7] driver_probe_device+0x4e/0x150
[ 46.671604][ T7] __device_attach_driver+0x1cc/0x2a0
[ 46.672192][ T7] bus_for_each_drv+0x156/0x1d0
[ 46.672739][ T7] page_owner free stack trace missing
[ 46.673335][ T7]
[ 46.673620][ T7] Memory state around the buggy address:
[ 46.674213][ T7] ffff888019442700: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 46.675083][ T7] ffff888019442780: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 46.675994][ T7] >ffff888019442800: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 46.676875][ T7] ^
[ 46.677323][ T7] ffff888019442880: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 46.678190][ T7] ffff888019442900: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 46.679052][ T7] ==================================================================
[ 46.679945][ T7] Disabling lock debugging due to kernel taint
[ 46.680725][ T7] Kernel panic - not syncing:
Ching-Te Ku [Wed, 8 Mar 2023 05:32:25 +0000 (13:32 +0800)]
wifi: rtw89: coex: Add v5 firmware cycle status report
To support v5 version firmware cycle report, apply the related structure
and functions. v5 cycle report add a group of status to show how the
free-run/TDMA training goes to. It is a firmware mechanism that can auto
adjust coexistence mode between TDMA and free run mechanism at 3 antenna
solution. v5 version provide more reference data to let the mechanism
make decision.
Ching-Te Ku [Wed, 8 Mar 2023 05:32:24 +0000 (13:32 +0800)]
wifi: rtw89: coex: Add v2 Bluetooth scan info
Compare to v1 and v2 removed some not usable parameters. Save firmware
code size. The information can show how frequent and how long the
Bluetooth scan do. It will help to debug coexistence issue.
Ching-Te Ku [Wed, 8 Mar 2023 05:32:21 +0000 (13:32 +0800)]
wifi: rtw89: coex: Add traffic TX/RX info and its H2C
There is a new mechanism which can do some real time performance
tuning for WiFi and BT. This TX/RX info is a condition provide to
firmware to do traffic analysis.
Ching-Te Ku [Wed, 8 Mar 2023 05:32:19 +0000 (13:32 +0800)]
wifi: rtw89: coex: Add more error_map and counter to log
The error map and counter can help to analyze is coexistence mechanism
going well or not. For example, if there is E2G (External control Wi-Fi
slot for Wi-Fi 2.4 GHz) hang counter, it means Wi-Fi firmware didn't cut
a slot for Wi-Fi 2.4 GHz. Maybe something wrong with firmware timer.
Jacob Keller [Tue, 7 Mar 2023 23:02:12 +0000 (15:02 -0800)]
wifi: qtnfmac: use struct_size and size_sub for payload length
Replace the calculations for the payload length in
qtnf_cmd_band_fill_iftype with struct_size() and size_sub(). While
the payload length does not get directly passed to an allocation function,
the performed calculation is still calculating the size of a flexible array
structure (minus the size of a header structure).
Jacob Keller [Tue, 7 Mar 2023 23:01:48 +0000 (15:01 -0800)]
wifi: ipw2x00: convert ipw_fw_error->elem to flexible array[]
The ipw_fw_error structure contains a payload[] flexible array as well as
two pointers to this array area, ->elem, and ->log. The total size of the
allocated structure is computed without use of the <linux/overflow.h>
macros.
There's no reason to keep both a payload[] and an extra pointer to both the
elem and log members. Convert the elem pointer member into the flexible
array member, removing payload.
Fix the allocation of the ipw_fw_error structure to use size_add(),
struct_size(), and array_size() to compute the allocation. This ensures
that any overflow saturates at SIZE_MAX rather than overflowing and
potentially allowing an undersized allocation.
Before the structure change, the layout of ipw_fw_error was:
Martin Kaiser [Tue, 7 Mar 2023 19:57:17 +0000 (20:57 +0100)]
wifi: rtl8xxxu: use module_usb_driver
We can use the module_usb_driver macro instead of open-coding the driver's
init and exit functions. This is simpler and saves some lines of code.
Other realtek wireless drivers use module_usb_driver as well.
Signed-off-by: Martin Kaiser <martin@kaiser.cx> Reviewed-by: Ping-Ke Shih <pkshih@realtek.com> Tested-by: Philipp Hortmann <philipp.g.hortmann@gmail.com> # Edimax N150 Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230307195718.168021-1-martin@kaiser.cx
Ping-Ke Shih [Tue, 7 Mar 2023 14:18:48 +0000 (22:18 +0800)]
wifi: rtw89: release RX standby timer of beamformee CSI to save power
Originally, we keep RX standby timer to handle beamformee CSI, but this
spends power and causes system not entering power save mode. To improve
power consumption, release the timer if throughput becomes low.
Martin Kaiser [Sun, 5 Mar 2023 17:59:32 +0000 (18:59 +0100)]
wifi: rtl8xxxu: mark Edimax EW-7811Un V2 as tested
The Edimax V2 (vid 0x7392, pid 0xb811) works well with the rtl8xxxu driver
since rtl8188eu support has been added. Remove the untested flag for this
device.
Hans de Goede [Fri, 3 Mar 2023 22:23:31 +0000 (23:23 +0100)]
wifi: brcmfmac: Use ISO3166 country code and rev 0 as fallback on 4356
Many devices ship with a nvram ccode value of X2/XT/XU/XV/ALL which are
all special world-wide compatibility ccode-s. Most of these world-wide
ccode-s allow passive scan mode only for 2.4GHz channels 12-14,
only enabling them when an AP is seen on them.
Since linux-firmware has moved to the new cyfmac4356-pci.bin +
cyfmac4356-pci.clm_blob firmware files this no longer works and
4356 devices using e.g. an X2 ccode fail to connect to an AP on
channel 13.
Add the 4356 chip-id to the list of chips for which to use the ISO3166
country code + rev 0 as fallback in brcmf_translate_country_code() to
fix this.
projects / mirror_ubuntu-kernels.git / log