Phil Sutter [Fri, 2 Dec 2016 10:39:46 +0000 (11:39 +0100)]
ss: Drop empty lines in UDP output
When dumping UDP sockets and show_tcpinfo (-i) is active but not
show_mem (-m), print_tcpinfo() does not output anything leading to an
empty line being printed after every socket. Fix this by skipping the
call to print_tcpinfo() and the previous newline printing in that case.
Cyrill Gorcunov [Wed, 2 Nov 2016 13:14:55 +0000 (16:14 +0300)]
libnetlink: Add test for error code returned from netlink reply
In case if some diag module is not present in the system,
say the kernel is not modern enough, we simply skip the
error code reported. Instead we should check for data
length in NLMSG_DONE and process unsupported case.
l2tp: read IPv6 UDP checksum attributes from kernel
In case of an older kernel that doesn't set L2TP_ATTR_UDP_ZERO_CSUM6_{RX,TX}
the old hard-coded value is being preserved, since the attribute flag will be
missing.
L2TP_ATTR_UDP_CSUM is read by the kernel as a NLA_FLAG value,
but is validated as a NLA_U8, so we will write it as an u8,
but the value isn't actually being read by the kernel.
It is written by the kernel as a NLA_U8, so we will read as
such.
Zhang Shengju [Sat, 19 Nov 2016 15:50:13 +0000 (23:50 +0800)]
libnetlink: reduce size of message sent to kernel
Fixes commit 246f57c4086d99fa ("ip link: Add support for kernel
side filtering").
This patch reduce the size of message sent to kernel space. Before this
patch, for command: 'ip link show', we will sent 1056 bytes. With this
patch, we only need to send 40 bytes.
Zhang Shengju [Fri, 18 Nov 2016 01:12:53 +0000 (09:12 +0800)]
iproute2: fix the link group name getting error
In the situation where more than one entry live in the same hash bucket,
loop to get the correct one.
Before:
$ cat /etc/iproute2/group
0 default
256 test
$ sudo ip link set group test dummy1
$ ip link show type dummy
11: dummy0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group 0 qlen 1000
link/ether 4e:3b:d3:6c:f0:e6 brd ff:ff:ff:ff:ff:ff
12: dummy1: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group test qlen 1000
link/ether d6:9c:a4:1f:e7:e5 brd ff:ff:ff:ff:ff:ff
After:
$ ip link show type dummy
11: dummy0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 4e:3b:d3:6c:f0:e6 brd ff:ff:ff:ff:ff:ff
12: dummy1: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group test qlen 1000
link/ether d6:9c:a4:1f:e7:e5 brd ff:ff:ff:ff:ff:ff
Adjusting iproute2 utility to support new macvlan link type mode called
"source".
Example of commands that can be applied:
ip link add link eth0 name macvlan0 type macvlan mode source
ip link set link dev macvlan0 type macvlan macaddr add 00:11:11:11:11:11
ip link set link dev macvlan0 type macvlan macaddr del 00:11:11:11:11:11
ip link set link dev macvlan0 type macvlan macaddr flush
ip -details link show dev macvlan0
Based on previous work of Stefan Gula <steweg@gmail.com>
Signed-off-by: Michael Braun <michael-dev@fami-braun.de> Cc: steweg@gmail.com
v5:
- rebase and fix checkpatch
v4:
- add MACADDR_SET support
- skip FLAG_UNICAST / FLAG_UNICAST_ALL as this is not upstream
- fix man page
Daniel Borkmann [Thu, 10 Nov 2016 00:20:59 +0000 (01:20 +0100)]
bpf: make tc's bpf loader generic and move into lib
This work moves the bpf loader into the iproute2 library and reworks
the tc specific parts into generic code. It's useful as we can then
more easily support new program types by just having the same ELF
loader backend. Joint work with Thomas Graf. I hacked a rough start
of a test suite to make sure nothing breaks [1] and looks all good.
Phil Sutter [Tue, 8 Nov 2016 21:29:11 +0000 (22:29 +0100)]
ipaddress: Simplify vf_info parsing
Commit 7b8179c780a1a ("iproute2: Add new command to ip link to
enable/disable VF spoof check") tried to add support for
IFLA_VF_SPOOFCHK in a backwards-compatible manner, but aparently overdid
it: parse_rtattr_nested() handles missing attributes perfectly fine in
that it will leave the relevant field unassigned so calling code can
just compare against NULL. There is no need to layback from the previous
(IFLA_VF_TX_RATE) attribute to the next to check if IFLA_VF_SPOOFCHK is
present or not. To the contrary, it establishes a potentially incorrect
assumption of these two attributes directly following each other which
may not be the case (although up to now, kernel aligns them this way).
This patch cleans up the code to adhere to the common way of checking
for attribute existence. It has been tested to return correct results
regardless of whether the kernel exports IFLA_VF_SPOOFCHK or not.
Signed-off-by: Phil Sutter <phil@nwl.cc> Reviewed-by: Greg Rose <grose@lightfleet.com>
Paul Blakey [Wed, 2 Nov 2016 15:09:58 +0000 (17:09 +0200)]
tc: flower: Fix usage message
Remove left over usage from removal of eth_type argument.
Fixes: 488b41d020fb ('tc: flower no need to specify the ethertype') Signed-off-by: Paul Blakey <paulb@mellanox.com> Reviewed-by: Simon Horman <simon.horman@netronome.com>
Isaac Boukris [Sat, 29 Oct 2016 19:20:19 +0000 (22:20 +0300)]
iproute2: ss: escape all null bytes in abstract unix domain socket
Abstract unix domain socket may embed null characters,
these should be translated to '@' when printed by ss the
same way the null prefix is currently being translated.
Daniel Borkmann [Tue, 18 Oct 2016 12:13:09 +0000 (14:13 +0200)]
tc, ipt: don't enforce iproute2 dependency on iptables-devel
Since 5cd1adba79d3 ("Update to current iptables headers") compilation
of iproute2 broke for systems without iptables-devel package [1].
Reason is that even though we fall back to build m_ipt.c, the include
depends on a xtables-version.h header, which only ships with
iptables-devel. Machines not having this package fail compilation with:
[...]
CC m_ipt.o
In file included from ../include/iptables.h:5:0,
from m_ipt.c:17:
../include/xtables.h:34:29: fatal error: xtables-version.h: No such file or directory
compilation terminated.
../Config:31: recipe for target 'm_ipt.o' failed
make[1]: *** [m_ipt.o] Error 1
The configure script only barks that package xtables was not found in
the pkg-config search path. The generated Config then only contains f.e.
TC_CONFIG_IPSET. In tc's Makefile we thus fall back to adding m_ipt.o
to TCMODULES. m_ipt.c then includes the local include/iptables.h header
copy, which includes the include/xtables.h copy. Latter then includes
xtables-version.h, which only ships with iptables-devel.
One way to resolve this is to skip this whole mess when pkg-config has
no xtables config available. I've carried something along these lines
locally for a while now, but it's just too annyoing. :/ Build works fine
now also when xtables.pc is not available.
Hangbin Liu [Sun, 9 Oct 2016 02:14:18 +0000 (10:14 +0800)]
devlink: Convert conditional in dl_argv_handle_port() to switch()
Discovered by Phil's covscan. The final return statement is never reached.
This is not inherently clear from looking at the code, so change the
conditional to a switch() statement which should clarify this.
CC: Phil Sutter <phil@nwl.cc> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Acked-by: Phil Sutter <phil@nwl.cc>
Recently a new per-port flag was added which controls the flooding of
unknown multicast, this patch adds support for controlling it via iproute2.
It also updates the man pages with information about the new flag.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Jakub Kicinski [Wed, 12 Oct 2016 15:46:36 +0000 (16:46 +0100)]
tc: cls_bpf: handle skip_sw and skip_hw flags
Add support for controling hardware offload using (now standard)
skip_sw and skip_hw flags in cls_bpf.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Simon Horman <simon.horman@netronome.com>
When I did the per-vlan stats iproute2 support, I left out a hunk from a
previous version of the patch that was using a special subcommand "stats".
Since the latest version uses the -s switch remove the help for the stats
subcommand.
Fixes: 7abf5de677e32 ("bridge: vlan: add support to display per-vlan statistics") Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Adjusting iproute2 utility to support new macvlan link type mode called
"source".
Example of commands that can be applied:
ip link add link eth0 name macvlan0 type macvlan mode source
ip link set link dev macvlan0 type macvlan macaddr add 00:11:11:11:11:11
ip link set link dev macvlan0 type macvlan macaddr del 00:11:11:11:11:11
ip link set link dev macvlan0 type macvlan macaddr flush
ip -details link show dev macvlan0
Based on previous work of Stefan Gula <steweg@gmail.com>
Signed-off-by: Michael Braun <michael-dev@fami-braun.de> Cc: steweg@gmail.com
Jamal Hadi Salim [Mon, 10 Oct 2016 16:45:14 +0000 (12:45 -0400)]
tc filters: add support to get individual filters by handle
sudo $TC filter add dev $ETH parent ffff: prio 2 protocol ip \
u32 match u32 0 0 flowid 1:1 \
action ok
sudo $TC filter add dev $ETH parent ffff: prio 1 protocol ip \
u32 match ip protocol 1 0xff flowid 1:10 \
action ok
now dump to see all rules..
$TC -s filter ls dev $ETH parent ffff: protocol ip
....
filter pref 1 u32
filter pref 1 u32 fh 801: ht divisor 1
filter pref 1 u32 fh 801::800 order 2048 key ht 801 bkt 0 flowid 1:10 (rule hit 0 success 0)
match 00010000/00ff0000 at 8 (success 0 )
action order 1: gact action drop
random type none pass val 0
index 6 ref 1 bind 1 installed 4 sec used 4 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
filter pref 2 u32
filter pref 2 u32 fh 800: ht divisor 1
filter pref 2 u32 fh 800::800 order 2048 key ht 800 bkt 0 flowid 1:1 (rule hit 336 success 336)
match 00000000/00000000 at 0 (success 336 )
action order 1: gact action pass
random type none pass val 0
index 5 ref 1 bind 1 installed 38 sec used 4 sec
Action statistics:
Sent 24864 bytes 336 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
....
..get filter 801::800
$TC -s filter get dev $ETH parent ffff: protocol ip \
handle 801:0:800 prio 2 u32
....
filter parent ffff: protocol ip pref 1 u32 fh 801::800 order 2048 key ht 801 bkt 0 flowid 1:10 (rule hit 260 success 130)
match 00010000/00ff0000 at 8 (success 130 )
action order 1: gact action drop
random type none pass val 0
index 6 ref 1 bind 1 installed 348 sec used 0 sec
Action statistics:
Sent 11440 bytes 130 pkt (dropped 130, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
....
..get other one
$TC -s filter get dev $ETH parent ffff: protocol ip \
handle 800:0:800 prio 2 u32
....
filter parent ffff: protocol ip pref 2 u32 fh 800::800 order 2048 key ht 800 bkt 0 flowid 1:1 (rule hit 514 success 514)
match 00000000/00000000 at 0 (success 514 )
action order 1: gact action pass
random type none pass val 0
index 5 ref 1 bind 1 installed 506 sec used 4 sec
Action statistics:
Sent 35544 bytes 514 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
....
..try something that doesnt exist
$TC -s filter get dev $ETH parent ffff: protocol ip handle 800:0:803 prio 2 u32
.....
RTNETLINK answers: No such file or directory
We have an error talking to the kernel
.....
Note, added NLM_F_ECHO is for backward compatibility. old kernels never
before Eric's patch will not respond without it and newer kernels (after Erics patch)
will ignore it.
In old kernels there is a side effect:
In addition to a response to the GET you will receive an event (if you do tc mon).
But this is still better than what it was before (not working at all).
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Jamal Hadi Salim [Tue, 11 Oct 2016 11:00:45 +0000 (07:00 -0400)]
actions: add skbmod action
This action is intended to be an upgrade from a usability perspective
from pedit (as well as operational debugability).
Compare this:
sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \
u32 match ip protocol 1 0xff flowid 1:2 \
action pedit munge offset -14 u8 set 0x02 \
munge offset -13 u8 set 0x15 \
munge offset -12 u8 set 0x15 \
munge offset -11 u8 set 0x15 \
munge offset -10 u16 set 0x1515 \
pipe
to:
sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \
u32 match ip protocol 1 0xff flowid 1:2 \
action skbmod dmac 02:15:15:15:15:15
Or worse, try to debug a policy with destination mac, source mac and
etherype. Then make that a hundred rules and you'll get my point.
The most important ethernet use case at the moment is when redirecting or
mirroring packets to a remote machine. The dst mac address needs a re-write
so that it doesn't get dropped or confuse an interconnecting (learning) switch
or dropped by a target machine (which looks at the dst mac).
In the future common use cases on pedit can be migrated to this action
(as an example different fields in ip v4/6, transports like tcp/udp/sctp
etc). For this first cut, this allows modifying basic ethernet header.
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Hangbin Liu [Fri, 23 Sep 2016 03:25:54 +0000 (11:25 +0800)]
ip rule: merge ip rule flush and list, save together
iprule_flush() and iprule_list_or_save() both call function
rtnl_wilddump_request() and rtnl_dump_filter(). So merge them
together just like other files do.
ip link: Add support to configure SR-IOV VF to vlan protocol 802.1ad (VST QinQ)
Introduce a new API that exposes a list of vlans per VF (IFLA_VF_VLAN_LIST),
giving the ability for user-space application to specify it for the VF as
an option to support 802.1ad (VST QinQ).
We introduce struct vf_vlan_info, which extends struct vf_vlan and adds
an optional VF VLAN proto parameter.
Default VLAN-protocol is 802.1Q.
Add IFLA_VF_VLAN_LIST in addition to IFLA_VF_VLAN to keep backward
compatibility with older kernel versions.
Suitable ip link tool command examples:
- Set vf vlan protocol 802.1ad (S-TAG)
ip link set eth0 vf 1 vlan 100 proto 802.1ad
- Set vf vlan S-TAG and vlan C-TAG (VST QinQ)
ip link set eth0 vf 1 vlan 100 proto 802.1ad vlan 30 proto 802.1Q
- Set vf to VST (802.1Q) mode
ip link set eth0 vf 1 vlan 100 proto 802.1Q
- Or by omitting the new parameter (backward compatible)
ip link set eth0 vf 1 vlan 100
The 'vlan modify' action allows to replace an existing 802.1q tag
according to user provided settings.
It accepts same arguments as the 'vlan push' action.
For example, this replaces vid 6 with vid 5:
# tc filter add dev veth0 parent ffff: pref 1 protocol 802.1q \
basic match 'meta(vlan mask 0xfff eq 6)' \
action vlan modify id 5 continue
Add support to dump the mroute cache entry age if the show_stats (-s)
switch is provided.
Example:
$ ip -s mroute
(0.0.0.0, 239.10.10.10) Iif: eth0 Oifs: eth0
0 packets, 0 bytes, Age 245.44
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Anton Aksola [Tue, 20 Sep 2016 06:01:27 +0000 (06:01 +0000)]
iproute2: build nsid-name cache only for commands that need it
The calling of netns_map_init() before command parsing introduced
a performance issue with large number of namespaces.
As commands such as add, del and exec do not need to iterate through
/var/run/netns it would be good not no build the cache before executing
these commands.
Example:
unpatched:
time seq 1 1000 | xargs -n 1 ip netns add
real 0m16.832s
user 0m1.350s
sys 0m15.029s
patched:
time seq 1 1000 | xargs -n 1 ip netns add
real 0m3.859s
user 0m0.132s
sys 0m3.205s
Signed-off-by: Anton Aksola <aakso@iki.fi> Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Currently, 'linkid' input by the user is parsed but 'handle' is appended to the netlink message.
# tc filter add dev enp1s0f1 protocol ip parent ffff: prio 99 u32 ht 800: \
order 1 link 1: offset at 0 mask 0f00 shift 6 plus 0 eat match ip \
protocol 6 ff
resulted in:
filter protocol ip pref 99 u32 fh 800::1 order 1 key ht 800 bkt 0
match 00060000/00ff0000 at 8
offset 0f00>>6 at 0 eat
This patch results in:
filter protocol ip pref 99 u32 fh 800::1 order 1 key ht 800 bkt 0 link 1:
match 00060000/00ff0000 at 8
offset 0f00>>6 at 0 eat
Lorenzo Colitti [Wed, 21 Sep 2016 16:02:50 +0000 (01:02 +0900)]
ss: Support displaying and filtering on socket marks.
This allows the user to dump sockets with a given mark (via
"fwmark = 0x1234/0x1234" or "fwmark = 12345", etc.) , and to
display the socket marks of dumped sockets.
The relevant kernel commits are: d545caca827b ("net: inet: diag:
expose the socket mark to privileged processes.") and
- a52e95abf772 ("net: diag: allow socket bytecode filters to
match socket marks")
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
ipmonitor: fix ip monitor can't work when NET_NS is not enabled
In ip monitor, netns_map_init will check getnsid is supported or not.
But when /proc/self/ns/net does not exist, we just print out error
messages and exit. So user cannot use ip monitor anymore when
CONFIG_NET_NS is disabled:
# ip monitor
open("/proc/self/ns/net"): No such file or directory
If open "/proc/self/ns/net" failed, set have_rtnl_getnsid to false.
Fixes: d652ccbf8195 ("netns: allow to dump and monitor nsid") Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com> Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Dump useful TCP BBR state information from a struct tcp_bbr_info that
was grabbed using the inet_diag API.
We tolerate info that is shorter or longer than expected, in case the
kernel is older or newer than the ss binary. We simply print the
minimum of what is expected from the kernel and what is provided from
the kernel. We use the same trick as that used for struct tcp_info:
when the info from the kernel is shorter than we hoped, we pad the end
with zeroes, and don't print fields if they are zero.
The BBR output looks like:
bbr:(bw:1.2Mbps,mrtt:18.965,pacing_gain:2.88672,cwnd_gain:2.88672)
The motivation here is to be consistent with DCTCP, which looks like:
dctcp(ce_state:23,alpha:23,ab_ecn:23,ab_tot:23)
projects / mirror_iproute2.git / log