Bluetooth: Change the way we set ERTM mode as mandatory
If the socket type is SOCK_STREAM we set Enhanced Retransmisson Mode or
Streaming Mode as mandatory. That means that we will close the channel
if the other side doesn't support or request the the mandatory mode.
Basic mode can't be set as mandatory.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi> Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Bluetooth: Tweaks to l2cap_send_i_or_rr_or_rnr() flow
l2cap_send_sframe() already set the F-bit if we set L2CAP_CONN_SEND_FBIT
and unset L2CAP_CONN_SEND_FBIT after send the F-bit.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi> Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi> Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Bluetooth: Fix ERTM error reporting to the userspace
If any error occurs during transfers we have to tell userspace that
something wrong happened.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi> Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Bluetooth: Fix missing retransmission action with RR(P=1)
The Bluetooth SIG Profile Tuning Suite Software uses the CSA1 spec
to run the L2CAP tests. The new 3.0 spec has a missing
Retransmit-I-Frames action when the Remote side is Busy.
We still start the retransmission timer if Remote is Busy and unacked
frames > 0. We do everything we did before this change plus the
Retransmission of I-frames.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi> Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We have to check if the proposed tx_window value is not greater that
maximum value supported.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi> Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
ERTM spec mandates that after receive a P-bit we shall send an F-bit in
response. This patch fixes this for retransmitted packets, on
retransmitting we were missing to check for a pending F-bit to be sent.
Also we were missing some annotation to send a F-bit.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi> Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Bluetooth: Stop ack_timer if ERTM enters in Local Busy or SREJ_SENT
The ack_timer is implemation specific, disabling it in such situation
avoids some potencial errors in the ERTM protocol.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi> Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Amitkumar Karwar [Thu, 27 May 2010 23:38:37 +0000 (16:38 -0700)]
Bluetooth: Process interrupt in main thread of btmrvl driver as well
When driver is sending a command or data and the firmware is also
sending a sleep event, sometimes it is observed that driver will
continue to send the command/data to firmware right after processing
sleep event. Once sleep event is processed driver is not supposed to
send anything because firmware is in sleep state after that. Previously
interrupt processing was done in SDIO interrupt callback handler.
Now it is done in btmrvl driver main thread to solve the
cross-sending properly.
Ron Shaffer [Fri, 28 May 2010 15:53:46 +0000 (11:53 -0400)]
Bluetooth: Reassigned copyright to Code Aurora Forum
Qualcomm, Inc. has reassigned rights to Code Aurora Forum. Accordingly,
as files are modified by Code Aurora Forum members, the copyright
statement will be updated.
Signed-off-by: Ron Shaffer <rshaffer@codeaurora.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Bluetooth: Fix warning: variable 'tty' set but not used
The patch below fixes a warning message when using gcc 4.6.0.
CC [M] drivers/bluetooth/hci_ldisc.o
drivers/bluetooth/hci_ldisc.c: In function 'hci_uart_send_frame':
drivers/bluetooth/hci_ldisc.c:213:21: warning: variable 'tty' set but not used
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com> Reviewed-By: Gustavo F. Padovan <gustavo@padovan.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch silences a compiler warning:
drivers/bluetooth/btmrvl_sdio.c: In function ‘btmrvl_sdio_verify_fw_download’:
drivers/bluetooth/btmrvl_sdio.c:80: warning: ‘fws1’ may be used uninitialized in this function
drivers/bluetooth/btmrvl_sdio.c:80: note: ‘fws1’ was declared here
Johan Hedberg [Tue, 18 May 2010 11:20:32 +0000 (13:20 +0200)]
Bluetooth: Add blacklist support for incoming connections
In some circumstances it could be desirable to reject incoming
connections on the baseband level. This patch adds this feature through
two new ioctl's: HCIBLOCKADDR and HCIUNBLOCKADDR. Both take a simple
Bluetooth address as a parameter. BDADDR_ANY can be used with
HCIUNBLOCKADDR to remove all devices from the blacklist.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When resending an I-frame, ERTM was reusing the control bits from the last
time it was sent, that was causing a corruption in the new control field
due to it dirty fields.
This patches extracts only the SAR bits from the old field and reuse it to
resend the packet, the others bits should be reset and receive the
updated value.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Bluetooth: Proper shutdown ERTM when closing the channel
Fix a crash regarding the Monitor Timeout, it was running even after the
shutdown of the ACL connection, which doesn't make sense.
The same code also fixes another issue, before this patch L2CAP was sending
many Disconnections Requests while we have to send only one.
The issues are related to each other, a expired Monitor Timeout can
trigger a Disconnection Request and then we may have a crash if the link
was already deleted.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since all TxSeq values are modulo, we shall not compare them directly. We
have to compare their offset inside the TxWindow instead.
Signed-off-by: João Paulo Rechi Vita <jprvita@profusion.mobi> Acked-by: Gustavo F. Padovan <padovan@profusion.mobi> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch makes l2cap_ertm_send() similar to the Send-Data action of
the ERTM spec. We shall not check for RemoteBusy or WAIT_F state
inside l2cap_ertm_send().
Such checks were causing a bug in the retransmission logic of ERTM and
making ERTM stalls until the ACL is dropped.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi> Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Bluetooth: Only check SAR bits if frame is an I-frame
The SAR bits doesn't make sense for an S-frame. It doesn't use SAR.
Checking SAR for a S-frames can lead to L2CAP errors, it could close
the channel with an invalid packet length, since we was removing the 2
of the of any frame that match SAR start bits, without check if it is
an I-frame.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
All ERTM operations regarding the txWindow should be modulo 64,
otherwise we confuse the ERTM logic and connections will break.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi> Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Bluetooth: Fix drop of packets with invalid req_seq/tx_seq
We shall not use an unsigned var since we are expecting negatives value
there. Using unsigned causes ERTM connection to close due to invalid
ReqSeq numbers.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Bluetooth: Remove L2CAP Extended Features from Kconfig
This reverts commit 84fb0a6334af0ccad3544f6972c055d90fbb9fbe which adds
the L2CAP Extended Features to the Kconfig, that is actually not needed.
One can use other mechanisms to enable L2CAP Extended Features.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fix merge conflict in drivers/vhost/net.c with guidance from
Stephen Rothwell.
Revert the effects of net-2.6 commit 573201f36fd9c7c6d5218cdcd9948cee700b277d
since net-next-2.6 has fixes that make bridge netpoll work properly thus
we don't need it disabled.
Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Horman [Tue, 20 Jul 2010 06:45:56 +0000 (06:45 +0000)]
drop_monitor: convert some kfree_skb call sites to consume_skb
Convert a few calls from kfree_skb to consume_skb
Noticed while I was working on dropwatch that I was detecting lots of internal
skb drops in several places. While some are legitimate, several were not,
freeing skbs that were at the end of their life, rather than being discarded due
to an error. This patch converts those calls sites from using kfree_skb to
consume_skb, which quiets the in-kernel drop_monitor code from detecting them as
drops. Tested successfully by myself
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Horman [Tue, 20 Jul 2010 04:52:09 +0000 (04:52 +0000)]
drop_monitor: Add error code to detect duplicate state changes
Patch to add -EAGAIN error to dropwatch netlink message handling code.
-EAGAIN will be returned anytime userspace attempts to transition the state of
the drop monitor service to a state that its already in. That allows user space
to detect this condition, so it doesn't wait for a success ACK that will never
arrive. Tested successfully by me
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb4vf: Fix off-by-one error checking for the end of the mailbox delay array
Fix off-by-one error in checking for the end of the mailbox response delay
array. We ended up walking off the end and, if we were unlucky, we'd end up
pulling in a 0 and never terminate the mailbox response delay loop ...
Signed-off-by: Casey Leedom <leedom@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Mon, 19 Jul 2010 19:26:45 +0000 (19:26 +0000)]
bridge: Partially disable netpoll support
The new netpoll code in bridging contains use-after-free bugs
that are non-trivial to fix.
This patch fixes this by removing the code that uses skbs after
they're freed.
As a consequence, this means that we can no longer call bridge
from the netpoll path, so this patch also removes the controller
function in order to disable netpoll.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Thanks, Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 20 Jul 2010 05:01:26 +0000 (22:01 -0700)]
ipv6: Make IP6CB(skb)->nhoff 16-bit.
Even with jumbograms I cannot see any way in which we would need
to records a larger than 65535 valued next-header offset.
The maximum extension header length is (256 << 3) == 2048.
There are only a handful of extension headers specified which
we'd even accept (say 5 or 6), therefore the largest next-header
offset we'd ever have to contend with is something less than
say 16k.
Therefore make it a u16 instead of a u32.
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Mon, 19 Jul 2010 14:15:04 +0000 (14:15 +0000)]
bnx2: Remove some unnecessary smp_mb() in tx fast path.
smp_mb() inside bnx2_tx_avail() is used twice in the normal
bnx2_start_xmit() path (see illustration below). The full memory
barrier is only necessary during race conditions with tx completion.
We can speed up the tx path by replacing smp_mb() in bnx2_tx_avail()
with a compiler barrier. The compiler barrier is to force the
compiler to fetch the tx_prod and tx_cons from memory.
In the race condition between bnx2_start_xmit() and bnx2_tx_int(),
we have the following situation:
bnx2_start_xmit() bnx2_tx_int()
if (!bnx2_tx_avail())
BUG();
...
if (!bnx2_tx_avail())
netif_tx_stop_queue(); update_tx_index();
smp_mb(); smp_mb();
if (bnx2_tx_avail()) if (netif_tx_queue_stopped() &&
netif_tx_wake_queue(); bnx2_tx_avail())
With smp_mb() removed from bnx2_tx_avail(), we need to add smp_mb() to
bnx2_start_xmit() as shown above to properly order netif_tx_stop_queue()
and bnx2_tx_avail() to check the ring index. If it is not strictly
ordered, the tx queue can be stopped forever.
This improves performance by about 5% with 2 ports running bi-directional
64-byte packets.
Reviewed-by: Benjamin Li <benli@broadcom.com> Reviewed-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Mon, 19 Jul 2010 14:15:03 +0000 (14:15 +0000)]
bnx2: Call pci_enable_msix() with actual number of vectors.
Based on original patch by Breno Leitão <leitao@linux.vnet.ibm.com>.
Allocate the actual number of vectors and make use of fewer vectors
if pci_enable_msix() returns > 0. We must allocate one additional
vector for the cnic driver.
Cc: Breno Leitão <leitao@linux.vnet.ibm.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Reviewed-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Mon, 19 Jul 2010 14:15:02 +0000 (14:15 +0000)]
bnx2: Use proper counter for net_device_stats->multicast.
We were using the wrong tx multicast counter instead of the rx multicast
counter.
Reported-by: Peter Snellman <peter.snellman@cinnober.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Reviewed-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Don Skidmore [Mon, 19 Jul 2010 14:00:47 +0000 (14:00 +0000)]
ixgbe: fix version string for ixgbe
Bump the version string to better reflect what is in the driver.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yi Zou [Mon, 19 Jul 2010 14:00:24 +0000 (14:00 +0000)]
ixgbe: use GFP_ATOMIC when allocating FCoE DDP context from the dma pool
The FCoE protocol stack may hold a lock when this gets called.
Signed-off-by: Yi Zou <yi.zou@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yi Zou [Mon, 19 Jul 2010 13:59:52 +0000 (13:59 +0000)]
ixgbe: properly toggling netdev feature flags when disabling FCoE
When FCoE is disabled, there is a race condition that FCoE offload is
turned off but the FCoE protocol driver is still queuing I/O thinking
offload support still exists. This patch toggles off corresponding FCoE
netdev feature flags and notify the FCoE stack first, allowing FCoE
protocol stack driver to update its flags upon NETDEV_FEAT_CHANGE so no
I/O will be using offload.
Also, indicate FCoE offload flags in vlan_features in ixgbe_probe once
and do not toggle them in ixgbe_fcoe_enable/disable so when FCoE is
created on the VLAN interface, vlan_transfer_features() would properly
update the VLAN netdev features flag and notify the FCoE protocol driver
for NETDEV_FEAT_CHANGE.
Signed-off-by: Yi Zou <yi.zou@intel.com> Tested-by: Ross Brattain <ross.b.brattain@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Mon, 19 Jul 2010 13:59:27 +0000 (13:59 +0000)]
ixgbe: drop support for UDP in RSS hash generation
This change removes UDP from the supported protocols for RSS hashing. The
reason for removing this protocol is because IP fragmentation was causing a
network flow to be broken into two streams, one for fragmented, and one for
non-fragmented and this in turn was causing out-of-order issues.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Acked-by: Don Skidmore <donald.c.skidmore@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend [Mon, 19 Jul 2010 13:59:03 +0000 (13:59 +0000)]
ixgbe: dcb, set DPF bit when PFC is enabled
Set the DPF bit when PFC is enabled. This will discard
PFC frames so they do not get passed up the stack.
The DPF bit is set for flow control, but not priority
flow control this brings pfc inline with fc.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Tested-by: Ross Brattain <ross.b.brattain@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Mon, 19 Jul 2010 13:43:47 +0000 (13:43 +0000)]
e1000: allow option to limit number of descriptors down to 48 per ring
This change makes it possible to limit the number of descriptors down to 48
per ring. The reason for this change is to address a variation on hardware
errata 10 for 82546GB in which descriptors will be lost if more than 32
descriptors are fetched and the PCI-X MRBC is 512.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Emil Tantilov <emil.s.tantilov@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
On SMP systems, the SMSC911x registers may be accessed by multiple CPUs
and this seems to put the chip in an inconsistent state. The patch adds
spinlocks to the smsc911x_reg_read, smsc911x_reg_write,
smsc911x_rx_readfifo and smsc911x_tx_writefifo functions.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net-next: vmxnet3 fixes [4/5] Do not reset when the device is not opened
Hold rtnl_lock to get the right link state.
While asynchronously resetting the device, hold rtnl_lock to get the
right value from netif_running. If a reset is scheduled, and the device
goes thru close and open, it may happen that reset and open may run in
parallel. Holding rtnl_lock will avoid this.
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ilpo Järvinen [Mon, 19 Jul 2010 01:16:18 +0000 (01:16 +0000)]
tcp: fix crash in tcp_xmit_retransmit_queue
It can happen that there are no packets in queue while calling
tcp_xmit_retransmit_queue(). tcp_write_queue_head() then returns
NULL and that gets deref'ed to get sacked into a local var.
There is no work to do if no packets are outstanding so we just
exit early.
This oops was introduced by 08ebd1721ab8fd (tcp: remove tp->lost_out
guard to make joining diff nicer).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Reported-by: Lennart Schulte <lennart.schulte@nets.rwth-aachen.de> Tested-by: Lennart Schulte <lennart.schulte@nets.rwth-aachen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 19 Jul 2010 16:35:40 +0000 (09:35 -0700)]
net: 64bit stats for netdev_queue
Since struct netdev_queue tx_bytes/tx_packets/tx_dropped are already
protected by _xmit_lock, its easy to convert these fields to u64 instead
of unsigned long.
This completes 64bit stats for devices using them (vlan, macvlan, ...)
Strictly, we could avoid the locking in dev_txq_stats_fold() on 64bit
arches, but its slow path and we prefer keep it simple.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 19 Jul 2010 03:24:14 +0000 (03:24 +0000)]
bonding: fix bond_inet6addr_event()
After commit ad1afb0039391 (vlan_dev: VLAN 0 should be treated
as "no vlan tag" (802.1p packet)),
bond_inet6addr_event() might be called with a NULL bond->vlgrp pointer, and
a non empty bond->vlan_list. vlan_group_get_device() is dereferencing a NULL pointer.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
s2io: Remove unnecessary memset of netdev private data
The memory for the private data is allocated using kzalloc in
alloc_etherdev (or alloc_netdev_mq respectively) so there is no need to
set it to 0 again.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Richard Cochran [Sat, 17 Jul 2010 08:49:36 +0000 (08:49 +0000)]
net: support time stamping in phy devices.
This patch adds a new networking option to allow hardware time stamps
from PHY devices. When enabled, likely candidates among incoming and
outgoing network packets are offered to the PHY driver for possible
time stamping. When accepted by the PHY driver, incoming packets are
deferred for later delivery by the driver.
The patch also adds phylib driver methods for the SIOCSHWTSTAMP ioctl
and callbacks for transmit and receive time stamping. Drivers may
optionally implement these functions.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at> Signed-off-by: David S. Miller <davem@davemloft.net>
Richard Cochran [Sat, 17 Jul 2010 08:49:17 +0000 (08:49 +0000)]
net: added a BPF to help drivers detect PTP packets.
Certain kinds of hardware time stamping units in both MACs and PHYs have
the limitation that they can only time stamp PTP packets. Drivers for such
hardware are left with the task of correctly matching skbs to time stamps.
This patch adds a BPF that drivers can use to classify PTP packets when
needed.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at> Signed-off-by: David S. Miller <davem@davemloft.net>
Richard Cochran [Sat, 17 Jul 2010 08:48:55 +0000 (08:48 +0000)]
net: preserve ifreq parameter when calling generic phy_mii_ioctl().
The phy_mii_ioctl() function unnecessarily throws away the original ifreq.
We need access to the ifreq in order to support PHYs that can perform
hardware time stamping.
Two maverick drivers filter the ioctl commands passed to phy_mii_ioctl().
This is unnecessary since phylib will check the command in any case.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at> Signed-off-by: David S. Miller <davem@davemloft.net>
Richard Cochran [Sat, 17 Jul 2010 08:48:28 +0000 (08:48 +0000)]
net: add driver hook for tx time stamping.
This patch adds a hook for transmit time stamps. The transmit hook
allows a software fallback for transmit time stamps, for MACs
lacking time stamping hardware. Using the hook will still require
adding an inline function call to each MAC driver.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at> Signed-off-by: David S. Miller <davem@davemloft.net>
Pedro Garcia [Sun, 18 Jul 2010 22:38:44 +0000 (15:38 -0700)]
vlan_dev: VLAN 0 should be treated as "no vlan tag" (802.1p packet)
- Without the 8021q module loaded in the kernel, all 802.1p packets
(VLAN 0 but QoS tagging) are silently discarded (as expected, as
the protocol is not loaded).
- Without this patch in 8021q module, these packets are forwarded to
the module, but they are discarded also if VLAN 0 is not configured,
which should not be the default behaviour, as VLAN 0 is not really
a VLANed packet but a 802.1p packet. Defining VLAN 0 makes it almost
impossible to communicate with mixed 802.1p and non 802.1p devices on
the same network due to arp table issues.
- Changed logic to skip vlan specific code in vlan_skb_recv if VLAN
is 0 and we have not defined a VLAN with ID 0, but we accept the
packet with the encapsulated proto and pass it later to netif_rx.
- In the vlan device event handler, added some logic to add VLAN 0
to HW filter in devices that support it (this prevented any traffic
in VLAN 0 to reach the stack in e1000e with HW filter under 2.6.35,
and probably also with other HW filtered cards, so we fix it here).
- In the vlan unregister logic, prevent the elimination of VLAN 0
in devices with HW filter.
- The default behaviour is to ignore the VLAN 0 tagging and accept
the packet as if it was not tagged, but we can still define a
VLAN 0 if desired (so it is backwards compatible).
Signed-off-by: Pedro Garcia <pedro.netdev@dondevamos.com> Signed-off-by: David S. Miller <davem@davemloft.net>
MAX_SOCK_ADDR is no longer used because commit 230b1839 "net: Use standard
structures for generic socket address structures." replaced
"char address[MAX_SOCK_ADDR];" with "struct sockaddr_storage address;".
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Sat, 17 Jul 2010 07:21:28 +0000 (07:21 +0000)]
arcnet: fix signed bug in probe function
probe_irq_off() returns the first irq found or if two irqs are found
then it returns the negative of the first irq found. We can cast
dev->irq to an int so that the test for negative values works.
Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6: fix CoA check in RH2 input handler (mip6_rthdr_input())
The input handler for Type 2 Routing Header (mip6_rthdr_input())
checks if the CoA in the packet matches the CoA in the XFRM state.
Current check is buggy: it compares the adddress in the Type 2
Routing Header, i.e. the HoA, against the expected CoA in the state.
The comparison should be made against the address in the destination
field of the IPv6 header.
The bug remained unnoticed because the main (and possibly only current)
user of the code (UMIP MIPv6 Daemon) initializes the XFRM state with the
unspecified address, i.e. explicitly allows everything.
Yoshifuji-san, can you ack that one?
Signed-off-by: Arnaud Ebalard <arno@natisbad.org> Signed-off-by: David S. Miller <davem@davemloft.net>
net-next: vmxnet3 fixes [3/5] Initialize link state at probe time
This change initializes the state of link at the time when driver is
loaded. The ethtool output for 'link detected' and 'link speed'
is thus valid even before the interface is brought up.
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Use DMA API as PCI equivalents will be deprecated. This change also allow
to allocate with GFP_KERNEL in some places.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2: allocate with GFP_KERNEL flag on RX path init
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Jennings [Fri, 16 Jul 2010 04:57:25 +0000 (04:57 +0000)]
ibmveth: lost IRQ while closing/opening device leads to service loss
The order of freeing the IRQ and freeing the device in firmware
in ibmveth_close can cause the adapter to become unusable after a
subsequent ibmveth_open. Only a reboot of the OS will make the
network device usable again. This is seen when cycling the adapter
up and down while there is network activity.
There is a window where an IRQ will be left unserviced (H_EOI will not
be called). The solution is to make a VIO_IRQ_DISABLE h_call, free the
device with firmware, and then call free_irq.
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Boyd [Fri, 16 Jul 2010 16:50:10 +0000 (09:50 -0700)]
rt2x00: Fix lockdep warning in rt2x00lib_probe_dev()
The rt2x00dev->intf_work workqueue is never initialized when a driver is
probed for a non-existent device (in this case rt2500usb). On such a
path we call rt2x00lib_remove_dev() to free any resources initialized
during the probe before we use INIT_WORK to initialize the workqueue.
This causes lockdep to get confused since the lock used in the workqueue
hasn't been initialized yet but is now being acquired during
cancel_work_sync() called by rt2x00lib_remove_dev().
Fix this by initializing the workqueue first before we attempt to probe
the device. This should make lockdep happy and avoid breaking any
assumptions about how the library cleans up after a probe fails.
vhost: avoid pr_err on condition guest can trigger
Guest can trigger packet truncation by posting
a very short buffer and disabling buffer merging.
Convert pr_err to pr_debug to avoid log from filling
up when this happens.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Ben Greear [Thu, 15 Jul 2010 13:22:33 +0000 (13:22 +0000)]
ipmr: Don't leak memory if fib lookup fails.
This was detected using two mcast router tables. The
pimreg for the second interface did not have a specific
mrule, so packets received by it were handled by the
default table, which had nothing configured.
This caused the ipmr_fib_lookup to fail, causing
the memory leak.
Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net-next: vmxnet3 fixes [2/5] Interrupt control bitmap
A new bit map 'intrCtrl' is introduced in the DriverShared area. The
driver should update VMXNET3_IC_DISABLE_ALL bit before writing IMR.
Signed-off-by: Ronghua Zang <ronghua@vmware.com> Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 16 Jul 2010 04:41:00 +0000 (21:41 -0700)]
tcp: sizeof struct tcp_skb_cb is 44
Correct comment stating sizeof(struct tcp_skb_cb) is 36 or 40, since its
44 bytes, since commit 951dbc8ac714b04 ([IPV6]: Move nextheader offset
to the IP6CB).
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Mason [Thu, 15 Jul 2010 08:47:28 +0000 (08:47 +0000)]
vxge: Version update
Version update
Signed-off-by: Jon Mason <jon.mason@exar.com> Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@exar.com> Signed-off-by: Ramkrishna Vepa <ramkrishna.vepa@exar.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Mason [Thu, 15 Jul 2010 08:47:27 +0000 (08:47 +0000)]
vxge: Update maintainers information
Update and correct maintainers information
Signed-off-by: Jon Mason <jon.mason@exar.com> Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@exar.com> Signed-off-by: Ramkrishna Vepa <ramkrishna.vepa@exar.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Mason [Thu, 15 Jul 2010 08:47:26 +0000 (08:47 +0000)]
vxge: Update copyright information
Update copyright information to reflect the Exar purchase of Neterion
Signed-off-by: Jon Mason <jon.mason@exar.com> Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@exar.com> Signed-off-by: Ramkrishna Vepa <ramkrishna.vepa@exar.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Mason [Thu, 15 Jul 2010 08:47:25 +0000 (08:47 +0000)]
vxge: NETIF_F_LLTX removal
NETIF_F_LLTX and it's usage of local transmit locks are depricated in
favor of using the netdev queue's transmit lock. Remove the local
lock and all references to it, and use the netdev queue transmit lock
in the transmit completion handler.
Signed-off-by: Jon Mason <jon.mason@exar.com> Signed-off-by: Ramkrishna Vepa <ramkrishna.vepa@exar.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Mason [Thu, 15 Jul 2010 08:47:24 +0000 (08:47 +0000)]
vxge: Fix multicast issues
Fix error in multicast flag check, add calls to restore the status of
multicast and promiscuous mode settings after change_mtu, and style
cleanups to shorten the function calls by using a temporary variable.
Signed-off-by: Jon Mason <jon.mason@exar.com> Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@exar.com> Signed-off-by: Ramkrishna Vepa <ramkrishna.vepa@exar.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Mason [Thu, 15 Jul 2010 08:47:23 +0000 (08:47 +0000)]
vxge: Remove queue_state references
Remove queue_state references, as they are no longer necessary.
Also, The driver needs to start/stop the queue regardless of which type
of steering is enabled. Remove checks for TX_MULTIQ_STEERING only and
start/stop for all steering types.
Signed-off-by: Jon Mason <jon.mason@exar.com> Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@exar.com> Signed-off-by: Ramkrishna Vepa <ramkrishna.vepa@exar.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6_skip_exthdr() can return error code that is below zero.
'offset' is unsigned, so it makes no sense.
ipv6_skip_exthdr() returns 'int' so we can painlessly change type of
offset to int.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com> Acked-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
'count' is unsigned. It is initialized to zero, then it can be increased
multiple times, and finally it is used in such a way:
>>>> count--;
|
| /* clear timestamp and dma mappings for remaining portion of packet */
| while (count >= 0) {
| count--;
| ...
^
If count is zero here (so, it was never increased), we would have a very
long loop :)
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Shevchenko [Thu, 15 Jul 2010 02:37:20 +0000 (02:37 +0000)]
drivers: isdn: get rid of custom strtoul()
There were two methods isdn_gethex() and isdn_getnum() which are custom
implementations of strtoul(). Get rid of them in regard to
strict_strtoul() kernel's function.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: Hansjoerg Lipp <hjlipp@web.de> Cc: Tilman Schmidt <tilman@imap.cc> Cc: Karsten Keil <isdn@linux-pingi.de> Cc: gigaset307x-common@lists.sourceforge.net Cc: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-eoan-kernel.git / log