Ben Hutchings [Thu, 2 Dec 2010 13:47:01 +0000 (13:47 +0000)]
sfc: Remove broken automatic fallback for invalid Falcon chip/board config
If the Falcon board config is invalid, we cannot proceed - we do not
have a valid board type to pass to falcon_probe_board(), and if we
kluge that to work with an unknown board then other initialisation
code will crash.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Steve Hodgson [Thu, 2 Dec 2010 13:46:55 +0000 (13:46 +0000)]
sfc: Fix event based MCDI completion and MC REBOOT/CMDDONE ordering issue
The mcfw *never* sends CMDDONE when rebooting. Changing this so that it always
sends CMDDONE *before* REBOOT is easy on Siena, but it's not obvious that we
could guarantee to be able to implement this on future hardware.
Given this, I'm less convinced that the protocol should be changed.
To reiterate the failure mode: The driver sees this:
issue command
receive REBOOT event
Was that reboot event sent before the command was issued, or in
response to the command? If the former then there will be a subsequent
CMDDONE event, if the latter, then there will be no CMDDONE event.
Options to resolve this are:
1. REBOOT always completes an outstanding mcdi request, and we set
the credits count to ignore a subsequent CMDDONE event with
mismatching seqno.
2. REBOOT never completes an outstanding mcdi request. If there is
no CMDDONE event then we rely on the mcdi timeout code to complete
the outstanding request, incurring a 10s delay.
I'd argue that (2) is tidier, but that incurring a 10s delay is a little
needless. Let's go with (1).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Thu, 2 Dec 2010 13:46:37 +0000 (13:46 +0000)]
sfc: Clear RXIN_SEL when soft-resetting QT2025C
When we enable PMA/PMD loopback this automatically sets RXIN_SEL
(inverse polarity for RXIN). We need to clear that bit during the
soft-reset sequence, as it is not done automatically.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Thu, 2 Dec 2010 13:46:24 +0000 (13:46 +0000)]
sfc: Distinguish critical and non-critical over-temperature conditions
Set both the 'maximum' and critical temperature limits for LM87
hardware monitors on Falcon boards. Do not shut down a port until the
critical temperature is reached, but warn as soon as the 'maximum'
temperature is reached.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Thu, 2 Dec 2010 13:46:09 +0000 (13:46 +0000)]
sfc: Reduce log level for MCDI error response in efx_mcdi_rpc()
Some errors are expected, e.g. when sending new commands to an MC
running old firmware. Only the caller of efx_mcdi_rpc() can decide
what is a real error. Therefore log the error responses with
netif_dbg().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Tue, 30 Nov 2010 12:01:03 +0000 (12:01 +0000)]
tipc: Delete tipc_ownidentity()
Moves the content of the native API routine tipc_ownidentity() into the
sole routine that calls it, since it can no longer be called in isolation.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Tue, 30 Nov 2010 12:01:02 +0000 (12:01 +0000)]
tipc: Eliminate obsolete native API forwarding routines
Moves the content of each native API message forwarding routine
into the sole routine that calls it, since the forwarding routines
no longer be called in isolation. Also removes code in each routine
that altered the outgoing message's importance level since this is
now no longer possible.
The previous function mapping (parent function, and child API) was
as follows:
tipc_send2name
\--tipc_forward2name
tipc_send2port
\--tipc_forward2port
tipc_send_buf2port
\--tipc_forward_buf2port
After this commit, the children don't exist and their functionality
is completely in the respective parent.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Tue, 30 Nov 2010 12:01:01 +0000 (12:01 +0000)]
tipc: Eliminate an unused symbolic constant in link code
Removes a symbol that is not referenced anywhere by TIPC's link code.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Tue, 30 Nov 2010 12:01:00 +0000 (12:01 +0000)]
tipc: Eliminate useless initialization when creating subscriber
Removes initialization of a local variable that is always assigned
a different value before it is referenced.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Tue, 30 Nov 2010 12:00:59 +0000 (12:00 +0000)]
tipc: Remove unused domain argument from multicast send routine
Eliminates an unused argument from tipc_multicast(), now that this
routine can no longer be called by kernel-based applications.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Tue, 30 Nov 2010 12:00:58 +0000 (12:00 +0000)]
tipc: Remove support for TIPC mode change callback
Eliminates support for the callback routine invoked when TIPC
changes its mode of operation from inactive to standalone or from
standalone to networked. This callback was part of TIPC's obsolete
native API and is not used by TIPC internally.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Tue, 30 Nov 2010 12:00:57 +0000 (12:00 +0000)]
tipc: Delete useless function prototypes
Removes several function declarations that aren't used anywhere,
either because they reference routines that no longer exist or
because all users of the function reference it after it has already
been defined.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Tue, 30 Nov 2010 12:00:56 +0000 (12:00 +0000)]
tipc: Eliminate useless return value when disabling a bearer
Modifies bearer_disable() to return void since it always indicates
success anyway.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Tue, 30 Nov 2010 12:00:55 +0000 (12:00 +0000)]
tipc: Delete unused configuration service structure definition
Removes a structure definition that is no longer used by TIPC's
configuration service.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Tue, 30 Nov 2010 12:00:54 +0000 (12:00 +0000)]
tipc: Remove obsolete inclusions of header files
Gets rid of #include statements that are no longer required as a
result of the merging of obsolete native API header file content
into other TIPC include files.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Tue, 30 Nov 2010 12:00:53 +0000 (12:00 +0000)]
tipc: Remove obsolete native API files and exports
As part of the removal of TIPC's native API support it is no longer
necessary for TIPC to export symbols for routines that can be called
by kernel-based applications, nor for it to have header files that
kernel-based applications can include to access the declarations for
those routines. This commit eliminates the exporting of symbols by
TIPC and migrates the contents of each obsolete native API include
file into its corresponding non-native API equivalent.
The code which was migrated in this commit was migrated intact, in
that there are no technical changes combined with the relocation.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tomoya [Mon, 29 Nov 2010 18:19:52 +0000 (18:19 +0000)]
can: EG20T PCH: Delete unnecessary spin_lock
Delete unnecessary spin_lock for accessing Message Object.
Since all message objects are divided into tx/rx area completely,
spin_lock processing is unnecessary.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com> Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Tomoya [Mon, 29 Nov 2010 18:11:52 +0000 (18:11 +0000)]
can: EG20T PCH: Separate Interface Register(IF1/IF2)
CAN register of Intel PCH EG20T has 2 sets of interface register.
To reduce whole of code size, separate interface register.
As a result, the number of function also can be reduced.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com> Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 2 Dec 2010 20:14:29 +0000 (12:14 -0800)]
tcp: Add timewait recycling bits to ipv6 connect code.
This will also improve handling of ipv6 tcp socket request
backlog when syncookies are not enabled. When backlog
becomes very deep, last quarter of backlog is limited to
validated destinations. Previously only ipv4 implemented
this logic, but now ipv6 does too.
Now we are only one step away from enabling timewait
recycling for ipv6, and that step is simply filling in
the implementation of tcp_v6_get_peer() and
tcp_v6_tw_get_peer().
Signed-off-by: David S. Miller <davem@davemloft.net>
If ipip is built as a module the 'ip tunnel add' command would fail because
the ipip module was not being autoloaded. Adding an alias for
the tunl0 device name cause dev_load() to autoload it when needed.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
If gre is built as a module the 'ip tunnel add' command would fail because
the ip_gre module was not being autoloaded. Adding an alias for
the gre0 device name cause dev_load() to autoload it when needed.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 29 Nov 2010 08:14:37 +0000 (08:14 +0000)]
net sched: use xps information for qdisc NUMA affinity
Allocate qdisc memory according to NUMA properties of cpus included in
xps map.
To be effective, qdisc should be (re)setup after changes
of /sys/class/net/eth<n>/queues/tx-<n>/xps_cpus
I added a numa_node field in struct netdev_queue, containing NUMA node
if all cpus included in xps_cpus share same node, else -1.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Cc: Ben Hutchings <bhutchings@solarflare.com> Cc: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Kravkov [Wed, 1 Dec 2010 20:39:28 +0000 (12:39 -0800)]
bnx2x: Add Nic partitioning mode (57712 devices)
NIC partitioning is another flavor of multi function - having few
PCI functions share the same physical port. Unlike the currently
supported mode of multi-function which depends on the switch
configuration and uses outer-VLAN, the NPAR mode is switch independent
and uses the MAC addresses to distribute incoming packets to the different
functions. This patch adds the specific HW setting of the NPAR mode
and some distinctions between switch dependent (SD) and
switch independent (SI) multi-function (MF) modes where the configuration
is not the same.
Advance driver version to 1.60.00-6
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 29 Nov 2010 21:37:14 +0000 (13:37 -0800)]
inet: Turn ->remember_stamp into ->get_peer in connection AF ops.
Then we can make a completely generic tcp_remember_stamp()
that uses ->get_peer() as a helper, minimizing the AF specific
code and minimizing the eventual code duplication when we implement
the ipv6 side of TW recycling.
Signed-off-by: David S. Miller <davem@davemloft.net>
Shan Wei [Mon, 29 Nov 2010 00:14:58 +0000 (00:14 +0000)]
sctp: kill unused macros in head file
1. SCTP_CMD_NUM_VERBS,SCTP_CMD_MAX
These two macros have never been used for several years since v2.6.12-rc2.
2.sctp_port_rover,sctp_port_alloc_lock
The commit 063930 abandoned global variables of port_rover and port_alloc_lock,
but still keep two macros to refer to them.
So, remove them now.
Scott J. Goldman [Sat, 27 Nov 2010 10:33:55 +0000 (10:33 +0000)]
vmxnet3: fix compilation when RSS is disabled
If RSS is disabled, we can ifdef out some RSS specific code. This fixes
the compile error found by Randy Dunlap.
Signed-off-by: Scott J. Goldman <scottjg@vmware.com> Reviewed-by: Bhavesh Davda <bhavesh@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Fri, 26 Nov 2010 08:36:09 +0000 (08:36 +0000)]
xps: Add CONFIG_XPS
This patch adds XPS_CONFIG option to enable and disable XPS. This is
done in the same manner as RPS_CONFIG. This is also fixes build
failure in XPS code when SMP is not enabled.
Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Fri, 26 Nov 2010 02:41:19 +0000 (02:41 +0000)]
qeth: enable interface setup if LAN is offline
Device initialization of a qeth device contains a STARTLAN step.
This step may fail, if cable is not yet plugged in. The qeth device
stays in state HARDSETUP until cable is plugged in. This prevents
further preparational initialization steps of the qeth device and
its network interface. This patch makes sure initialization of qeth
device continues, even though cable is not yet plugged in.
Once carrier is available, qeth is notified, triggers a recovery
which results in a working network interface.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Fri, 26 Nov 2010 02:41:18 +0000 (02:41 +0000)]
drivers/s390/net: Remove unnecessary semicolons
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Update the s390 network drivers(qeth & lcs) code to adapt to this change.
V2 : Changes based on suggestions given by Eric Dumazet
Signed-off-by: Sachin Sant <sachinp@in.ibm.com> Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac: fix stmmac_resume removing not yet used shutdown flag
The commit to convert to use the dev_pm_ops struct
introduces a bug. The shutdown flag is not yet used
because the hibernation on memory is done by using
the freeze callback.
Thanks to Vlad for having reported it.
Reported-by: Vlad Lungu <vlad.lungu@windriver.com> Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Breno Leitao [Thu, 25 Nov 2010 07:53:55 +0000 (07:53 +0000)]
cxgb3: Removing unused return variable
Currently the ret variable is not used for anything other than
receive the value of the t3_adapter_error(), which will always be 0,
because the reset parameter is 0.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jozsef Kadlecsik [Thu, 25 Nov 2010 03:15:07 +0000 (03:15 +0000)]
ipv6: Prepare the tree for un-inlined jhash.
jhash is widely used in the kernel and because the functions
are inlined, the cost in size is significant. Also, the new jhash
functions are slightly larger than the previous ones so better un-inline.
As a preparation step, the calls to the internal macros are replaced
with the plain jhash function calls.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu> Signed-off-by: David S. Miller <davem@davemloft.net>
Jonas Bonn [Thu, 25 Nov 2010 02:30:30 +0000 (02:30 +0000)]
ethoc: rework mdio read/write
MDIO read and write were checking whether a timeout had expired to determine
whether to recheck the result of the MDIO operation. Under heavy CPU usage,
however, it was possible for the timeout to expire before the routine got
around to be able to check a second time even, thus erroneousy returning an
-EBUSY.
This patch changes the the MDIO IO routines to try up to five times to complete
the operation before giving up, thus lessening the dependency on CPU load.
This resolves a problem whereby a ping flood would keep the CPU so busy that
the above problem would manifest itself; the MDIO command to check link status
would fail and the interface would erroneously be shut down.
Signed-off-by: Jonas Bonn <jonas@southpole.se> Signed-off-by: David S. Miller <davem@davemloft.net>
Jonas Bonn [Thu, 25 Nov 2010 02:30:29 +0000 (02:30 +0000)]
ethoc: rework interrupt handling
The old interrupt handling was incorrect in that it did not account for the
fact that the interrupt source bits get set irregardless of whether or not
their corresponding mask is set. This patch fixes that by masking off the
source bits for masked interrupts.
Furthermore, the handling of transmission events is moved to the NAPI polling
handler alongside the reception handler, thus preventing a whole bunch of
interrupts during heavy traffic.
Signed-off-by: Jonas Bonn <jonas@southpole.se> Signed-off-by: David S. Miller <davem@davemloft.net>
Jonas Bonn [Thu, 25 Nov 2010 02:30:28 +0000 (02:30 +0000)]
ethoc: Double check pending RX packet
An interrupt may occur between checking bd.stat and clearing the
interrupt source register which would result in the packet going totally
unnoticed as the interrupt will be missed. Double check bd.stat after
clearing the interrupt source register to guard against such an
occurrence.
Signed-off-by: Jonas Bonn <jonas@southpole.se> Signed-off-by: David S. Miller <davem@davemloft.net>
Adam Edvardsson [Thu, 25 Nov 2010 02:30:27 +0000 (02:30 +0000)]
ethoc: enable interrupts after napi_complete
Occasionally, it seems that some race is causing the interrupts to not be
reenabled otherwise with the end result that networking just stops working.
Enabling interrupts after calling napi_complete is more in line with what
other drivers do.
Signed-off-by: Jonas Bonn <jonas@southpole.se> Signed-off-by: David S. Miller <davem@davemloft.net>
Jonas Bonn [Thu, 25 Nov 2010 02:30:25 +0000 (02:30 +0000)]
ethoc: Add device tree configuration
This patch adds the ability to describe ethernet devices via a flattened
device tree. As device tree remains an optional feature, these bits all
need to be guarded by CONFIG_OF ifdefs.
MAC address is settable via the device tree parameter "local-mac-address";
however, the selection of the phy id is limited to probing, for now.
Signed-off-by: Jonas Bonn <jonas@southpole.se> Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x: Use helpers instead of direct access to the shinfo(skb) fields
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Wed, 24 Nov 2010 13:48:55 +0000 (13:48 +0000)]
bnx2: Remove config access to non-standard registers
In KVM passthrough mode, the driver may not have config access to
non-standard registers. The BNX2_PCICFG_MISC_CONFIG config register
access to setup mailbox swapping can be done using MMIO.
Update version to 2.0.20.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eddie Wai [Wed, 24 Nov 2010 13:48:54 +0000 (13:48 +0000)]
bnx2: Fix reset bug on 5709
The 5709 chip requires the BNX2_MISC_NEW_CORE_CTL_DMA_ENABLE bit to be
cleared and polling for pending DMAs to complete before chip reset.
Without this step, we've seen NMIs during repeated resets of the chip.
Signed-off-by: Eddie Wai <waie@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-jammy-kernel.git / log