arch/m68k/include/asm/raw_io.h:20:19: error:
cast to pointer from integer of different size
arch/m68k/include/asm/raw_io.h:30:32: error:
cast to pointer from integer of different size [-Werror=int-to-p
On m68k, io functions are defined as macros. The problem is seen if the
macro parameter variable size differs from the size of a pointer. Cast
the parameter of all io macros to unsigned long before casting it to
a pointer to fix the problem.
The Synopsys Ethernet IP uses the CSR clock as a base clock for MDC.
The divisor used is set in the MAC_MDIO_Address register field CR
(Clock Rate)
The divisor is there to change the CSR clock into a clock that falls
below the IEEE 802.3 specified max frequency of 2.5MHz.
If the CSR clock is 300MHz, the code falls back to using the reset
value in the MAC_MDIO_Address register, as described in the comment
above this code.
However, 300MHz is actually an allowed value and the proper divider
can be estimated quite easily (it's just 1Hz difference!)
A CSR frequency of 300MHz with the maximum clock rate value of 0x5
(STMMAC_CSR_250_300M, a divisor of 124) gives somewhere around
~2.42MHz which is below the IEEE 802.3 specified maximum.
For the ARTPEC-8 SoC, the CSR clock is this problematic 300MHz,
and unfortunately, the reset-value of the MAC_MDIO_Address CR field
is 0x0.
This leads to a clock rate of zero and a divisor of 42, and gives an
MDC frequency of ~7.14MHz.
Allow CSR clock of 300MHz by making the comparison inclusive.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
plat_dev->dev->platform_data is released by platform_device_unregister(),
use of pclk and hclk is a use-after-free. Since device unregister won't
need a clk device we adjust the function call sequence to fix this issue.
[ 31.261225] BUG: KASAN: use-after-free in macb_remove+0x77/0xc6 [macb_pci]
[ 31.275563] Freed by task 306:
[ 30.276782] platform_device_release+0x25/0x80
Suggested-by: Nicolas Ferre <Nicolas.Ferre@microchip.com> Signed-off-by: Tong Zhang <ztong0001@gmail.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
ioctl$SG_IO(/dev/sda, SG_IO, ...)
// Enters trace_note_tsk() after blk_trace_free() returned
// Use mdelay in rcu region rather than msleep(which may schedule out)
Remove blk_trace from running_list before calling blk_trace_free() by
sysfs if blk_trace is at Blktrace_running state.
Commit b0140891a8cea3 ("md: Fix race when creating a new md device.")
not only moved assigning mddev->gendisk before calling add_disk, which
fixes the races described in the commit log, but also added a
mddev->open_mutex critical section over add_disk and creation of the
md kobj. Adding a kobject after add_disk is racy vs deleting the gendisk
right after adding it, but md already prevents against that by holding
a mddev->active reference.
On the other hand taking this lock added a lock order reversal with what
is not disk->open_mutex (used to be bdev->bd_mutex when the commit was
added) for partition devices, which need that lock for the internal open
for the partition scan, and a recent commit also takes it for
non-partitioned devices, leading to further lockdep splatter.
Fixes: b0140891a8ce ("md: Fix race when creating a new md device.") Fixes: d62633873590 ("block: support delayed holder registration") Reported-by: syzbot+fadc0aaf497e6a493b9f@syzkaller.appspotmail.com Signed-off-by: Christoph Hellwig <hch@lst.de> Tested-by: syzbot+fadc0aaf497e6a493b9f@syzkaller.appspotmail.com Reviewed-by: NeilBrown <neilb@suse.de> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The limit should be "PAGE_SIZE - len" instead of "PAGE_SIZE". We're not
going to hit the limit so this fix will not affect runtime.
Link: https://lore.kernel.org/r/20210916132331.GE25094@kili Fixes: 5b9e70b22cc5 ("scsi: lpfc: raise sg count for nvme to use available sg resources") Reviewed-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The problem is the mismatched types between "ctx->total_len" which is
an unsigned int, "rc" which is an int, and "ctx->rc" which is a
ssize_t. The code does:
ctx->rc = (rc == 0) ? ctx->total_len : rc;
We want "ctx->rc" to store the negative "rc" error code. But what
happens is that "rc" is type promoted to a high unsigned int and
'ctx->rc" will store the high positive value instead of a negative
value.
The fix is to change "rc" from an int to a ssize_t.
Fixes: c610c4b619e5 ("CIFS: Add asynchronous write support through kernel AIO") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
After printing the list of thermal governors, then this function prints
a newline character. The problem is that "size" has not been updated
after printing the last governor. This means that it can write one
character (the NUL terminator) beyond the end of the buffer.
Get rid of the "size" variable and just use "PAGE_SIZE - count" directly.
Fixes: 1b4f48494eb2 ("thermal: core: group functions related to governor handling") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20210916131342.GB25094@kili Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
'set_signals()' in synclink_gt.c conflicts with an exported symbol
in arch/um/, so change set_signals() to set_gtsignals(). Keep
the function names similar by also changing get_signals() to
get_gtsignals().
../drivers/tty/synclink_gt.c:442:13: error: conflicting types for ‘set_signals’
static void set_signals(struct slgt_info *info);
^~~~~~~~~~~
In file included from ../include/linux/irqflags.h:16:0,
from ../include/linux/spinlock.h:58,
from ../include/linux/mm_types.h:9,
from ../include/linux/buildid.h:5,
from ../include/linux/module.h:14,
from ../drivers/tty/synclink_gt.c:46:
../arch/um/include/asm/irqflags.h:6:5: note: previous declaration of ‘set_signals’ was here
int set_signals(int enable);
^~~~~~~~~~~
Fixes: 705b6c7b34f2 ("[PATCH] new driver synclink_gt") Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jirislaby@kernel.org> Cc: Paul Fulghum <paulkf@microgate.com> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Link: https://lore.kernel.org/r/20210902003806.17054-1-rdunlap@infradead.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Forward declarations make the code larger and rewrites harder. Harder as
they are often omitted from global changes. Remove forward declarations
which are not really needed, i.e. the definition of the function is
before its first use.
ISCSI_NET_PARAM_IFACE_ENABLE belongs to enum iscsi_net_param instead of
iscsi_iface_param so move it to ISCSI_NET_PARAM. Otherwise, when we call
into the driver, we might not match and return that we don't want attr
visible in sysfs. Found in code review.
Link: https://lore.kernel.org/r/20210901085336.2264295-1-libaokun1@huawei.com Fixes: e746f3451ec7 ("scsi: iscsi: Fix iface sysfs attr detection") Reviewed-by: Lee Duncan <lduncan@suse.com> Signed-off-by: Baokun Li <libaokun1@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
If the HW device is during recovery, the HW resources will never return,
hence we shouldn't wait for the CID (HW context ID) bitmaps to clear.
This fix speeds up the error recovery flow.
Fixes: 64515dc899df ("qed: Add infrastructure for error detection and recovery") Signed-off-by: Michal Kalderon <mkalderon@marvell.com> Signed-off-by: Ariel Elior <aelior@marvell.com> Signed-off-by: Shai Malin <smalin@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The smallest TX ring size we support must fit a TX SKB with MAX_SKB_FRAGS
+ 1. Because the first TX BD for a packet is always a long TX BD, we
need an extra TX BD to fit this packet. Define BNXT_MIN_TX_DESC_CNT with
this value to make this more clear. The current code uses a minimum
that is off by 1. Fix it using this constant.
The tx_wake_thresh to determine when to wake up the TX queue is half the
ring size but we must have at least BNXT_MIN_TX_DESC_CNT for the next
packet which may have maximum fragments. So the comparison of the
available TX BDs with tx_wake_thresh should be >= instead of > in the
current code. Otherwise, at the smallest ring size, we will never wake
up the TX queue and will cause TX timeout.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.") Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadocm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
irq_set_affinity_hit() stores a reference to the cpumask_t
parameter in the irq descriptor, and that reference can be
accessed later from irq_affinity_hint_proc_show(). Since
the cpu_mask parameter passed to irq_set_affinity_hit() has
only temporary storage (it's on the stack memory), later
accesses to it are illegal. Thus reads from the corresponding
procfs affinity_hint file can result in paging request oops.
The issue is fixed by the get_cpu_mask() helper, which provides
a permanent storage for the cpumask_t parameter.
Fixes: d4fd0404c1c9 ("enetc: Introduce basic PF and VF ENETC ethernet drivers") Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The AFS filesystem is currently triggering the silly-rename cleanup from
afs_d_revalidate() when it sees that a dentry has been changed by a third
party[1]. It should not be doing this as the cleanup includes deleting the
silly-rename target file on iput.
Fix this by removing the places in the d_revalidate handling that validate
anything other than the directory and the dirent. It probably should not
be looking to validate the target inode of the dentry also.
This includes removing the point in afs_d_revalidate() where the inode that
a dentry used to point to was marked as being deleted (AFS_VNODE_DELETED).
We don't know it got deleted. It could have been renamed or it could have
hard links remaining.
This was reproduced by cloning a git repo onto an afs volume on one
machine, switching to another machine and doing "git status", then
switching back to the first and doing "git status". The second status
would show weird output due to ".git/index" getting deleted by the above
mentioned mechanism.
A simpler way to do it is to do:
machine 1: touch a
machine 2: touch b; mv -f b a
machine 1: stat a
on an afs volume. The bug shows up as the stat failing with ENOENT and the
file server log showing that machine 1 deleted "a".
If resource allocation and registration fail for a muxed tty device
(e.g. if there are no more minor numbers) the driver should not try to
deregister the never-registered (or already-deregistered) tty.
Fix up the error handling to avoid dereferencing a NULL pointer when
attempting to remove the character device.
Fixes: 72dc1c096c70 ("HSO: add option hso driver") Cc: stable@vger.kernel.org # 2.6.27 Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
It's not uncommon where __btrfs_dump_space_info() gets called
under over-commit situations.
In that case free space would underflow as total allocated space is not
enough to handle all the over-committed space.
Such underflow values can sometimes cause confusion for users enabled
enospc_debug mount option, and takes some seconds for developers to
convert the underflow value to signed result.
Just output the free space as s64 to avoid such problem.
Reported-by: Eli V <eliventer@gmail.com> Link: https://lore.kernel.org/linux-btrfs/CAJtFHUSy4zgyhf-4d9T+KdJp9w=UgzC2A0V=VtmaeEpcGgm1-Q@mail.gmail.com/ CC: stable@vger.kernel.org # 5.4+ Reviewed-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
There are two bugs:
1) If ida_simple_get() fails then this code calls put_device(carrier)
but we haven't yet called get_device(carrier) and probably that
leads to a use after free.
2) After device_initialize() then we need to use put_device() to
release the bus. This will free the internal resources tied to the
device and call mcb_free_bus() which will free the rest.
Fixes: 5d9e2ab9fea4 ("mcb: Implement bus->dev.release callback") Fixes: 18d288198099 ("mcb: Correctly initialize the bus's device") Cc: stable@vger.kernel.org Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Johannes Thumshirn <jth@kernel.org> Link: https://lore.kernel.org/r/32e160cf6864ce77f9d62948338e24db9fd8ead9.1630931319.git.johannes.thumshirn@wdc.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
During BC_FREE_BUFFER processing, the BINDER_TYPE_FDA object
cleanup may close 1 or more fds. The close operations are
completed using the task work mechanism -- which means the thread
needs to return to userspace or the file object may never be
dereferenced -- which can lead to hung processes.
Force the binder thread back to userspace if an fd is closed during
BC_FREE_BUFFER handling.
Fixes: 80cd795630d6 ("binder: fix use-after-free due to ksys_close() during fdget()") Cc: stable <stable@vger.kernel.org> Reviewed-by: Martijn Coenen <maco@android.com> Acked-by: Christian Brauner <christian.brauner@ubuntu.com> Signed-off-by: Todd Kjos <tkjos@google.com> Link: https://lore.kernel.org/r/20210830195146.587206-1-tkjos@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
If the driver runs out of minor numbers it would release minor 0 and
allow another device to claim the minor while still in use.
Fortunately, registering the tty class device of the second device would
fail (with a stack dump) due to the sysfs name collision so no memory is
leaked.
Fixes: cae2bc768d17 ("usb: cdc-acm: Decrement tty port's refcount if probe() fail") Cc: stable@vger.kernel.org # 4.19 Cc: Jaejoong Kim <climbbb.kim@gmail.com> Acked-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20210907082318.7757-1-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
ScanLogic SL11R-IDE with firmware older than 2.6c (the latest one) has
broken tag handling, preventing the device from working at all:
usb 1-1: new full-speed USB device number 2 using uhci_hcd
usb 1-1: New USB device found, idVendor=04ce, idProduct=0002, bcdDevice= 2.60
usb 1-1: New USB device strings: Mfr=1, Product=1, SerialNumber=0
usb 1-1: Product: USB Device
usb 1-1: Manufacturer: USB Device
usb-storage 1-1:1.0: USB Mass Storage device detected
scsi host2: usb-storage 1-1:1.0
usbcore: registered new interface driver usb-storage
usb 1-1: reset full-speed USB device number 2 using uhci_hcd
usb 1-1: reset full-speed USB device number 2 using uhci_hcd
usb 1-1: reset full-speed USB device number 2 using uhci_hcd
usb 1-1: reset full-speed USB device number 2 using uhci_hcd
Add US_FL_BULK_IGNORE_TAG to fix it. Also update my e-mail address.
2.6c is the only firmware that claims Linux compatibility.
The firmware can be upgraded using ezotgdbg utility:
https://github.com/asciilifeform/ezotgdbg
Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Ondrej Zary <linux@zary.sk> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20210913210106.12717-1-linux@zary.sk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The initial observation was that in PV mode under Xen 32-bit user space
didn't work anymore. Attempts of system calls ended in #GP(0x402). All
of the sudden the vector 0x80 handler was not in place anymore. As it
turns out up to 5.13 redundant initialization did occur: Once from
cpu_initialize_context() (through its VCPUOP_initialise hypercall) and a
2nd time while each CPU was brought fully up. This 2nd initialization is
now gone, uncovering that the 1st one was flawed: Unlike for the
set_trap_table hypercall, a full virtual IDT needs to be specified here;
the "vector" fields of the individual entries are of no interest. With
many (kernel) IDT entries still(?) (i.e. at that point at least) empty,
the syscall vector 0x80 ended up in slot 0x20 of the virtual IDT, thus
becoming the domain's handler for vector 0x20.
Make xen_convert_trap_info() fit for either purpose, leveraging the fact
that on the xen_copy_trap_info() path the table starts out zero-filled.
This includes moving out the writing of the sentinel, which would also
have lead to a buffer overrun in the xen_copy_trap_info() case if all
(kernel) IDT entries were populated. Convert the writing of the sentinel
to clearing of the entire table entry rather than just the address
field.
(I didn't bother trying to identify the commit which uncovered the issue
in 5.14; the commit named below is the one which actually introduced the
bad code.)
Although very unlikely that the tlink pointer would be null in this case,
get_next_mid function can in theory return null (but not an error)
so need to check for null (not for IS_ERR, which can not be returned
here).
Address warning:
fs/smbfs_client/connect.c:2392 cifs_match_super()
warn: 'tlink' isn't an ERR_PTR
Pointed out by Dan Carpenter via smatch code analysis tool
CC: stable@vger.kernel.org Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
This is writing to the first 1 - 3 bytes of "val" and then writing all
four bytes to musb_writel(). The last byte is always going to be
garbage. Zero out the last bytes instead.
Fixes: 550a7375fe72 ("USB: Add MUSB and TUSB support") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20210916135737.GI25094@kili Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
When last descriptor in a descriptor list completed with XferComplete
interrupt, core switching to handle next descriptor and assert BNA
interrupt. Both these interrupts are set while dwc2_hsotg_epint()
handler called. Each interrupt should be handled separately: first
XferComplete interrupt then BNA interrupt, otherwise last completed
transfer will not be giveback to function driver as completed
request.
According USB spec each ISOC transaction should be performed in a
designated for that transaction interval. On bus errors or delays
in operating system scheduling of client software can result in no
packet being transferred for a (micro)frame. An error indication
should be returned as status to the client software in such a case.
Current implementation in case of missed/dropped interval send same
data in next possible interval instead of reporting missed isoc.
This fix complete requests with -ENODATA if interval elapsed.
HSOTG core in BDMA and Slave modes haven't HW support for
(micro)frames tracking, this is why SW should care about tracking
of (micro)frames. Because of that method and consider operating
system scheduling delays, added few additional checking's of elapsed
target (micro)frame:
1. Immediately before enabling EP to start transfer.
2. With any transfer completion interrupt.
3. With incomplete isoc in/out interrupt.
4. With EP disabled interrupt because of incomplete transfer.
5. With OUT token received while EP disabled interrupt (for OUT
transfers).
6. With NAK replied to IN token interrupt (for IN transfers).
As part of ISOC flow, additionally fixed 'current' and 'target' frame
calculation functions. In HS mode SOF limits provided by DSTS register
is 0x3fff, but in non HS mode this limit is 0x7ff.
Tested by internal tool which also using for dwc3 testing.
This loop is supposed to loop until if reads something other than
CS_IDST or until it times out after 30,000 attempts. But because of
the || vs && bug, it will never time out and instead it will loop a
minimum of 30,000 times.
This bug is quite old but the code is only used in USB_DEVICE_TEST_MODE
so it probably doesn't affect regular usage.
Fixes: 96fe53ef5498 ("usb: gadget: r8a66597-udc: add support for TEST_MODE") Cc: stable <stable@vger.kernel.org> Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Acked-by: Felipe Balbi <balbi@kernel.org> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/20210906094221.GA10957@kili Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
ocfs2_data_convert_worker() is currently dropping any cached acl info
for FILE before down-converting meta lock. It should also drop for
DIRECTORY. Otherwise the second acl lookup returns the cached one (from
VFS layer) which could be already stale.
The problem we are seeing is that the acl changes on one node doesn't
get refreshed on other nodes in the following case:
drivers/gpu/drm/nouveau/nvkm/engine/device/ctrl.c: In function 'nvkm_control_mthd_pstate_info':
drivers/gpu/drm/nouveau/nvkm/engine/device/ctrl.c:60:35: error: overflow in conversion from 'int' to '__s8' {aka 'signed char'} changes value from '-251' to '5'
The code builds on most architectures, but fails on parisc where ENOSYS
is defined as 251.
Replace the error code with -ENODEV (-19). The actual error code does
not really matter and is not passed to userspace - it just has to be
negative.
Fixes: 7238eca4cf18 ("drm/nouveau: expose pstate selection per-power source in sysfs") Signed-off-by: Guenter Roeck <linux@roeck-us.net> Cc: Ben Skeggs <bskeggs@redhat.com> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The pending timer has been set up in blk_throtl_init(). However, the
timer is not deleted in blk_throtl_exit(). This means that the timer
handler may still be running after freeing the timer, which would
result in a use-after-free.
Fix by calling del_timer_sync() to delete the timer in blk_throtl_exit().
A consumer is expected to disable a PWM before calling pwm_put(). And if
they didn't there is hopefully a good reason (or the consumer needs
fixing). Also if disabling an enabled PWM was the right thing to do,
this should better be done in the framework instead of in each low level
driver.
A consumer is expected to disable a PWM before calling pwm_put(). And if
they didn't there is hopefully a good reason (or the consumer needs
fixing). Also if disabling an enabled PWM was the right thing to do,
this should better be done in the framework instead of in each low level
driver.
A consumer is expected to disable a PWM before calling pwm_put(). And if
they didn't there is hopefully a good reason (or the consumer needs
fixing). Also if disabling an enabled PWM was the right thing to do,
this should better be done in the framework instead of in each low level
driver.
kobject_put() should be used to cleanup the memory associated with the
kobject instead of kobject_del(). See the section "Kobject removal" of
"Documentation/core-api/kobject.rst".
If kobject_init_and_add returns with error, kobject_put() is needed here
to avoid memory leak, because kobject_init_and_add may return error
without freeing the memory associated with the kobject it allocated.
The kobject_put() should be used to cleanup the memory associated with the
kobject instead of kobject_del. See the section "Kobject removal" of
"Documentation/core-api/kobject.rst".
If kobject_init_and_add return with error, kobject_put() is needed here to
avoid memory leak, because kobject_init_and_add may return error without
freeing the memory associated with the kobject it allocated.
In nilfs_##name##_attr_release, kobj->parent should not be referenced
because it is a NULL pointer. The release() method of kobject is always
called in kobject_put(kobj), in the implementation of kobject_put(), the
kobj->parent will be assigned as NULL before call the release() method.
So just use kobj to get the subgroups, which is more efficient and can fix
a NULL pointer reference problem.
Patch series "nilfs2: fix incorrect usage of kobject".
This patchset from Nanyong Sun fixes memory leak issues and a NULL
pointer dereference issue caused by incorrect usage of kboject in nilfs2
sysfs implementation.
If kobject_init_and_add return with error, then the cleanup of kobject
is needed because memory may be allocated in kobject_init_and_add
without freeing.
And the place of cleanup_dev_kobject should use kobject_put to free the
memory associated with the kobject. As the section "Kobject removal" of
"Documentation/core-api/kobject.rst" says, kobject_del() just makes the
kobject "invisible", but it is not cleaned up. And no more cleanup will
do after cleanup_dev_kobject, so kobject_put is needed here.
Both of these threads hold uuid_mutex which is sufficient to protect
getting the seed device(s) freed while we are trying to clone it for
sprouting [2] or mounting a sprout [1] (as above). A mounted seed device
can not free/write/replace because it is read-only. An unmounted seed
device can be freed by btrfs_free_stale_devices(), but it needs
uuid_mutex. So this patch removes the unnecessary device_list_mutex in
clone_fs_devices(). And adds a lockdep_assert_held(&uuid_mutex) in
clone_fs_devices().
Reported-by: Su Yue <l@damenly.su> Tested-by: Su Yue <l@damenly.su> Signed-off-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The current code will update the mtime and then try to get caps to
handle the write. If we end up having to request caps from the MDS, then
the mtime in the cap grant will clobber the updated mtime and it'll be
lost.
This is most noticable when two clients are alternately writing to the
same file. Fw caps are continually being granted and revoked, and the
mtime ends up stuck because the updated mtimes are always being
overwritten with the old one.
Fix this by changing the order of operations in ceph_write_iter to get
the caps before updating the times. Also, make sure we check the pool
full conditions before even getting any caps or uninlining.
URL: https://tracker.ceph.com/issues/46574 Reported-by: Jozef Kováč <kovac@firma.zoznam.sk> Signed-off-by: Jeff Layton <jlayton@kernel.org> Reviewed-by: Xiubo Li <xiubli@redhat.com> Reviewed-by: Luis Henriques <lhenriques@suse.de> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The xilinx dma driver uses the consistent allocations, so for correct
operation also set the DMA mask for coherent APIs. It fixes the below
kernel crash with dmatest client when DMA IP is configured with 64-bit
address width and linux is booted from high (>4GB) memory.
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zou Wei <zou_wei@huawei.com> Reviewed-by: Baolin Wang <baolin.wang7@gmail.com> Link: https://lore.kernel.org/r/1620094977-70146-1-git-send-email-zou_wei@huawei.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
DEFINE_SMP_CALL_CACHE_FUNCTION() was usefel before the CPU hotplug rework
to ensure that the cache related functions are called on the upcoming CPU
because the notifier itself could run on any online CPU.
The hotplug state machine guarantees that the callbacks are invoked on the
upcoming CPU. So there is no need to have this SMP function call
obfuscation. That indirection was missed when the hotplug notifiers were
converted.
This also solves the problem of ARM64 init_cache_level() invoking ACPI
functions which take a semaphore in that context. That's invalid as SMP
function calls run with interrupts disabled. Running it just from the
callback in context of the CPU hotplug thread solves this.
Fixes: 8571890e1513 ("arm64: Add support for ACPI based firmware tables") Reported-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Will Deacon <will@kernel.org> Acked-by: Peter Zijlstra <peterz@infradead.org> Link: https://lore.kernel.org/r/871r69ersb.ffs@tglx Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
There are two pairs of declarations for thermal_cooling_device_register()
and thermal_of_cooling_device_register(), and only one set was changed
in a recent patch, so the other one now causes a compile-time warning:
drivers/net/wireless/mediatek/mt76/mt7915/init.c: In function 'mt7915_thermal_init':
drivers/net/wireless/mediatek/mt76/mt7915/init.c:134:48: error: passing argument 1 of 'thermal_cooling_device_register' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
134 | cdev = thermal_cooling_device_register(wiphy_name(wiphy), phy,
| ^~~~~~~~~~~~~~~~~
In file included from drivers/net/wireless/mediatek/mt76/mt7915/init.c:7:
include/linux/thermal.h:407:39: note: expected 'char *' but argument is of type 'const char *'
407 | thermal_cooling_device_register(char *type, void *devdata,
| ~~~~~~^~~~
Change the dummy helper functions to have the same arguments as the
normal version.
Fixes: f991de53a8ab ("thermal: make device_register's type argument const") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20210722090717.1116748-1-arnd@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Commit 05a4a9527931 ("kernel/watchdog: split up config options") adds a
new config HARDLOCKUP_DETECTOR, which selects the non-existing config
HARDLOCKUP_DETECTOR_ARCH.
Refer to the databook of DesignWare Cores Ethernet MAC Universal:
6.2.1.5 Register 4 (Transmit Descriptor List Address Register
If this register is not changed when the ST bit is set to 0, then
the DMA takes the descriptor address where it was stopped earlier.
The stmmac_tx_err() does zero indices to Tx descriptors, but does
not reset HW current Tx descriptor address. To fix inconsistency,
the base address of the Tx descriptors should be rewritten before
restarting Tx.
Signed-off-by: Jongsung Kim <neidhard.kim@lge.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Macpaul Lin <macpaul.lin@mediatek.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
commit 93c0970493c71f ("net: phy: consider latched link-down status in
polling mode") removed double-read of latched link-state register for
polling mode from genphy_update_link(). This added extra ~1s delay into
sequence link down->up.
Following scenario:
- After boot link goes up
- phy_start() is called triggering an aneg restart, hence link goes
down and link-down info is latched.
- After aneg has finished link goes up. In phy_state_machine is checked
link state but it is latched "link is down". The state machine is
scheduled after one second and there is detected "link is up". This
extra delay can be avoided when we keep link-state register double read
in case when link was down previously.
With this solution we don't miss a link-down event in polling mode and
link-up is faster.
Details about this quirky behavior on Realtek phy:
Without patch:
T0: aneg is started, link goes down, link-down status is latched
T0+3s: state machine runs, up-to-date link-down is read
T0+4s: state machine runs, aneg is finished (BMSR_ANEGCOMPLETE==1),
here i read link-down (BMSR_LSTATUS==0),
T0+5s: state machine runs, aneg is finished (BMSR_ANEGCOMPLETE==1),
up-to-date link-up is read (BMSR_LSTATUS==1),
phydev->link goes up, state change PHY_NOLINK to PHY_RUNNING
With patch:
T0: aneg is started, link goes down, link-down status is latched
T0+3s: state machine runs, up-to-date link-down is read
T0+4s: state machine runs, aneg is finished (BMSR_ANEGCOMPLETE==1),
first BMSR read: BMSR_ANEGCOMPLETE==1 and BMSR_LSTATUS==0,
second BMSR read: BMSR_ANEGCOMPLETE==1 and BMSR_LSTATUS==1,
phydev->link goes up, state change PHY_NOLINK to PHY_RUNNING
Signed-off-by: Petr Oros <poros@redhat.com> Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Macpaul Lin <macpaul.lin@mediatek.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
This fixes a race condition: After pwmchip_add() is called there might
already be a consumer and then modifying the hardware behind the
consumer's back is bad. So set the default before.
(Side-note: I don't know what this register setting actually does, if
this modifies the polarity there is an inconsistency because the
inversed polarity isn't considered if the PWM is already running during
.probe().)
Fixes: acfd92fdfb93 ("pwm: lpc32xx: Set PWM_PIN_LEVEL bit to default value") Cc: Sylvain Lemieux <slemieux@tycoint.com> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Syzbot reported shift-out-of-bounds bug in profile_init().
The problem was in incorrect prof_shift. Since prof_shift value comes from
userspace we need to clamp this value into [0, BITS_PER_LONG -1]
boundaries.
Second possible shiht-out-of-bounds was found by Tetsuo:
sample_step local variable in read_profile() had "unsigned int" type,
but prof_shift allows to make a BITS_PER_LONG shift. So, to prevent
possible shiht-out-of-bounds sample_step type was changed to
"unsigned long".
Also, "unsigned short int" will be sufficient for storing
[0, BITS_PER_LONG] value, that's why there is no need for
"unsigned long" prof_shift.
Link: https://lkml.kernel.org/r/20210813140022.5011-1-paskripkin@gmail.com Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-and-tested-by: syzbot+e68c89a9510c159d9684@syzkaller.appspotmail.com Suggested-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp> Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
When the refcount is decreased to 0, the resource reclamation branch is
entered. Before CPU0 reaches the race point (1), CPU1 may obtain the
spinlock and traverse the rbtree to find 'root', see
nilfs_lookup_root().
Although CPU1 will call refcount_inc() to increase the refcount, it is
obviously too late. CPU0 will release 'root' directly, CPU1 then
accesses 'root' and triggers UAF.
Use refcount_dec_and_lock() to ensure that both the operations of
decrease refcount to 0 and link deletion are lock protected eliminates
this risk.
Keno Fischer reported that when a binray loaded via ld-linux-x the
prctl(PR_SET_MM_MAP) doesn't allow to setup brk value because it lays
before mm:end_data.
This of course prevent criu from restoring such programs. Looking into
how kernel operates with brk/start_brk inside brk() syscall I don't see
any problem if we allow to setup brk/start_brk without checking for
end_data. Even if someone pass some weird address here on a purpose then
the worst possible result will be an unexpected unmapping of existing vma
(own vma, since prctl works with the callers memory) but test for
RLIMIT_DATA is still valid and a user won't be able to gain more memory in
case of expanding VMAs via new values shipped with prctl call.
Link: https://lkml.kernel.org/r/20210121221207.GB2174@grain Fixes: bbdc6076d2e5 ("binfmt_elf: move brk out of mmap when doing direct loader exec") Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com> Reported-by: Keno Fischer <keno@juliacomputing.com> Acked-by: Andrey Vagin <avagin@gmail.com> Tested-by: Andrey Vagin <avagin@gmail.com> Cc: Dmitry Safonov <0x7f454c46@gmail.com> Cc: Kirill Tkhai <ktkhai@virtuozzo.com> Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: Pavel Tikhomirov <ptikhomirov@virtuozzo.com> Cc: Alexander Mikhalitsyn <alexander.mikhalitsyn@virtuozzo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Currently the CRST parsing relies on the fact that on most of x86 devices
the IRQ mapping is 1:1 with Linux vIRQ. However, it may be not true for
some. Fix this by converting GSI to Linux vIRQ before checking it.
drivers/staging/rtl8192u/r8192U_core.c:4268:20: warning: bitwise and of
boolean expressions; did you mean logical and? [-Wbool-operation-and]
bpacket_toself = bpacket_match_bssid &
^~~~~~~~~~~~~~~~~~~~~
&&
1 warning generated.
Replace the bitwise AND with a logical one to clear up the warning, as
that is clearly what was intended.
When SCTP handles an INIT chunk, it calls for example:
sctp_sf_do_5_1B_init
sctp_verify_init
sctp_verify_param
sctp_process_init
sctp_process_param
handling of SCTP_PARAM_SET_PRIMARY
sctp_verify_init() wasn't doing proper size validation and neither the
later handling, allowing it to work over the chunk itself, possibly being
uninitialized memory.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
In one of the fallbacks that SCTP has for identifying an association for an
incoming packet, it looks for AddIp chunk (from ASCONF) and take a peek.
Thing is, at this stage nothing was validating that the chunk actually had
enough content for that, allowing the peek to happen over uninitialized
memory.
Similar check already exists in actual asconf handling in
sctp_verify_asconf().
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
FTRACE_ADDR is only defined when CONFIG_DYNAMIC_FTRACE is defined, the
latter is even stronger requirement than CONFIG_FUNCTION_TRACER (which is
enough for MCOUNT_ADDR).
Link: https://lists.01.org/hyperkitty/list/kbuild-all@lists.01.org/thread/ZUVCQBHDMFVR7CCB7JPESLJEWERZDJ3T/ Fixes: 1f12fb25c5c5d22f ("ARM: 9079/1: ftrace: Add MODULE_PLTS support") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Strangely I hadn't had noticed the existence of the list_entry_is_head()
in apparmor code when added the same one in the list.h. Luckily it's
fully identical and didn't break builds. In any case we don't need a
duplicate anymore, thus remove it from apparmor code.
Link: https://lkml.kernel.org/r/20201208100639.88182-1-andriy.shevchenko@linux.intel.com Fixes: e130816164e244 ("include/linux/list.h: add a macro to test if entry is pointing to the head") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: John Johansen <john.johansen@canonical.com> Cc: James Morris <jmorris@namei.org> Cc: "Serge E . Hallyn " <serge@hallyn.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Nobuhiro Iwamatsu (CIP) <nobuhiro1.iwamatsu@toshiba.co.jp> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
We do not need a SWIOTLB unless we have DRAM that is addressable beyond
the arm_dma_limit. Compare max_pfn with arm_dma_pfn_limit to determine
whether we do need a SWIOTLB to be initialized.
Fixes: ad3c7b18c5b3 ("arm: use swiotlb for bounce buffering on LPAE configs") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
We should not walk/touch page tables outside of VMA boundaries when
holding only the mmap sem in read mode. Evil user space can modify the
VMA layout just before this function runs and e.g., trigger races with
page table removal code since commit dd2283f2605e ("mm: mmap: zap pages
with read mmap_sem in munmap").
find_vma() does not check if the address is >= the VMA start address;
use vma_lookup() instead.
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com> Reviewed-by: Liam R. Howlett <Liam.Howlett@oracle.com> Fixes: dd2283f2605e ("mm: mmap: zap pages with read mmap_sem in munmap") Signed-off-by: David Hildenbrand <david@redhat.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The Linux console's VT102 implementation already consumes OSC
("Operating System Command") sequences, probably because that's how
palette changes are transmitted.
In addition to OSC, there are three other major clases of ANSI control
strings: APC ("Application Program Command"), PM ("Privacy Message"),
and DCS ("Device Control String"). They are handled similarly to OSC in
terms of termination.
Source: vt100.net
Add three new enumerated states, one for each of these types. All three
are handled the same way right now--they simply consume input until
terminated. I hope to expand upon this firmament in the future. Add
new predicate ansi_control_string(), returning true for any of these
states. Replace explicit checks against ESosc with calls to this
function. Transition to these states appropriately from the escape
initiation (ESesc) state.
This was motivated by the following Notcurses bugs:
where standard VT sequences are not consumed by the Linux console. It's
not necessary that the Linux console *support* these sequences, but it
ought *consume* these well-specified classes of sequences.
Tested by sending a variety of escape sequences to the console, and
verifying that they still worked, or were now properly consumed.
Verified that the escapes were properly terminated at a generic level.
Verified that the Notcurses tools continued to show expected output on
the Linux console, except now without escape bleedthrough.
Link: https://lore.kernel.org/lkml/YSydL0q8iaUfkphg@schwarzgerat.orthanc/ Signed-off-by: nick black <dankamongmen@gmail.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jirislaby@kernel.org> Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Fetching an index for any vcpu in kvm->vcpus array by traversing
the entire array everytime is costly.
This patch remembers the position of each vcpu in kvm->vcpus array
by storing it in vcpus_idx under kvm_vcpu structure.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Nitesh Narayan Lal <nitesh@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[borntraeger@de.ibm.com]: backport to 4.19 (also fits for 5.4) Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Acked-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Set CRSVIS flag in emulated root PCI bridge to indicate support for
Completion Retry Status.
Add check for CRSSVE flag from root PCI brige when issuing Configuration
Read Request via PIO to correctly returns fabricated CRS value as it is
required by PCIe spec.
Most callers of config read do not check for return value. But most of the
ones that do, checks for error indication in 'val' variable.
This patch updates error handling in advk_pcie_rd_conf() function. If PIO
transfer fails then 'val' variable is set to 0xffffffff which indicates
failture.
Perform conversion to little-endian before every write to configuration
space and convert it back to CPU endianness on reads.
Additionally, initialise every multiple byte field of config space with
the cpu_to_le* macro, which is required since the structure describing
config space of emulated bridge assumes little-endian convention.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
projects / mirror_ubuntu-focal-kernel.git / log