The driver overrides the error codes returned by platform_get_irq() to
-ENXIO, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the
error codes upstream.
Fixes: 9ec36cafe43b ("of/irq: do irq resolution in platform_get_irq") Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru> Link: https://lore.kernel.org/r/20230617203622.6812-7-s.shtylyov@omp.ru Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The driver overrides the error codes returned by platform_get_irq() to
-ENXIO, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the
error codes upstream.
Fixes: 9ec36cafe43b ("of/irq: do irq resolution in platform_get_irq") Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru> Link: https://lore.kernel.org/r/20230617203622.6812-6-s.shtylyov@omp.ru Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The driver overrides the error codes returned by platform_get_irq() to
-ENXIO, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the
error codes upstream.
Fixes: 9ec36cafe43b ("of/irq: do irq resolution in platform_get_irq") Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru> Link: https://lore.kernel.org/r/20230617203622.6812-5-s.shtylyov@omp.ru Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The driver overrides the error codes returned by platform_get_irq() to
-EINVAL, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the
error codes upstream.
In case the QCA7000 is not available via SPI (e.g. in reset),
the driver will cause a high load. The reason for this is
that the synchronization is never finished and schedule()
is never called. Since the synchronization is not timing
critical, it's safe to drop this from the scheduling condition.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Fixes: 291ab06ecf67 ("net: qualcomm: new Ethernet over SPI driver for QCA7000") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When running workloads heavy unbalanced towards TX (high TX, low RX
traffic), sfc driver can retain the CPU during too long times. Although
in many cases this is not enough to be visible, it can affect
performance and system responsiveness.
A way to reproduce it is to use a debug kernel and run some parallel
netperf TX tests. In some systems, this will lead to this message being
logged:
kernel:watchdog: BUG: soft lockup - CPU#12 stuck for 22s!
The reason is that sfc driver doesn't account any NAPI budget for the TX
completion events work. With high-TX/low-RX traffic, this makes that the
CPU is held for long time for NAPI poll.
Documentations says "drivers can process completions for any number of Tx
packets but should only process up to budget number of Rx packets".
However, many drivers do limit the amount of TX completions that they
process in a single NAPI poll.
In the same way, this patch adds a limit for the TX work in sfc. With
the patch applied, the watchdog warning never appears.
Tested with netperf in different combinations: single process / parallel
processes, TCP / UDP and different sizes of UDP messages. Repeated the
tests before and after the patch, without any noticeable difference in
network or CPU performance.
Test hardware:
Intel(R) Xeon(R) CPU E5-1620 v4 @ 3.50GHz (4 cores, 2 threads/core)
Solarflare Communications XtremeScale X2522-25G Network Adapter
Fixes: 5227ecccea2d ("sfc: remove tx and MCDI handling from NAPI budget consideration") Fixes: d19a53721863 ("sfc_ef100: TX path for EF100 NICs") Reported-by: Fei Liu <feliu@redhat.com> Signed-off-by: Íñigo Huguet <ihuguet@redhat.com> Acked-by: Martin Habets <habetsm.xilinx@gmail.com> Link: https://lore.kernel.org/r/20230615084929.10506-1-ihuguet@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When TUNNEL_L3_TO_L2 decap action was created, a pointer to a local
variable was passed as its HW action data, resulting in attempt to
free invalid address:
BUG: KASAN: invalid-free in mlx5dr_action_destroy+0x318/0x410 [mlx5_core]
With offloading enabled, esp_xmit() gets invoked very late, from within
validate_xmit_xfrm() which is after validate_xmit_skb() validates and
linearizes the skb if the underlying device does not support fragments.
esp_output_tail() may add a fragment to the skb while adding the auth
tag/ IV. Devices without the proper support will then send skb->data
points to with the correct length so the packet will have garbage at the
end. A pcap sniffer will claim that the proper data has been sent since
it parses the skb properly.
It is not affected with INET_ESP_OFFLOAD disabled.
Linearize the skb after offloading if the sending hardware requires it.
It was tested on v4, v6 has been adopted.
Fixes: 7785bba299a8d ("esp: Add a software GRO codepath") Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
There are some MD5 tests which fail when the kernel is in FIPS mode,
since MD5 is not FIPS compliant. Add a check and only run those tests
if FIPS mode is not enabled.
Fixes: f0bee1ebb5594 ("fcnal-test: Add TCP MD5 tests") Fixes: 5cad8bce26e01 ("fcnal-test: Add TCP MD5 tests for VRF") Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: Magali Lemes <magali.lemes@canonical.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The vrf-xfrm-tests tests use the hmac(md5) and cbc(des3_ede)
algorithms for performing authentication and encryption, respectively.
This causes the tests to fail when fips=1 is set, since these algorithms
are not allowed in FIPS mode. Therefore, switch from hmac(md5) and
cbc(des3_ede) to hmac(sha1) and cbc(aes), which are FIPS compliant.
Fixes: 3f251d741150 ("selftests: Add tests for vrf and xfrms") Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: Magali Lemes <magali.lemes@canonical.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
TLS selftests use the ChaCha20-Poly1305 and SM4 algorithms, which are not
FIPS compliant. When fips=1, this set of tests fails. Add a check and only
run these tests if not in FIPS mode.
Fixes: 4f336e88a870 ("selftests/tls: add CHACHA20-POLY1305 to tls selftests") Fixes: e506342a03c7 ("selftests/tls: add SM4 GCM/CCM to tls selftests") Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Magali Lemes <magali.lemes@canonical.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The sysctl net/core/bpf_jit_enable does not work now due to commit 1022a5498f6f ("bpf, x86_64: Use bpf_jit_binary_pack_alloc"). The
commit saved the jitted insns into 'rw_image' instead of 'image'
which caused bpf_jit_dump not dumping proper content.
With 'echo 2 > /proc/sys/net/core/bpf_jit_enable', run
'./test_progs -t fentry_test'. Without this patch, one of jitted
image for one particular prog is:
flen=17 proglen=92 pass=4 image=0000000014c64883 from=test_progs pid=1807 00000000: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc 00000010: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc 00000020: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc 00000030: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc 00000040: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc 00000050: cc cc cc cc cc cc cc cc cc cc cc cc
With this patch, the jitte image for the same prog is:
Fixes: 1022a5498f6f ("bpf, x86_64: Use bpf_jit_binary_pack_alloc") Signed-off-by: Yonghong Song <yhs@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Song Liu <song@kernel.org> Link: https://lore.kernel.org/bpf/20230609005439.3173569-1-yhs@fb.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Before Linux v5.8 an AF_INET6 SOCK_DGRAM (udp/udplite) socket
with SOL_UDP, UDP_ENCAP, UDP_ENCAP_ESPINUDP{,_NON_IKE} enabled
would just unconditionally use xfrm4_udp_encap_rcv(), afterwards
such a socket would use the newly added xfrm6_udp_encap_rcv()
which only handles IPv6 packets.
Cc: Sabrina Dubroca <sd@queasysnail.net> Cc: Steffen Klassert <steffen.klassert@secunet.com> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Benedict Wong <benedictwong@google.com> Cc: Yan Yan <evitayan@google.com> Fixes: 0146dca70b87 ("xfrm: add support for UDPv6 encapsulation of ESP") Signed-off-by: Maciej Żenczykowski <maze@google.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Reviewed-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The following scenario describes a bug in the verifier where it
incorrectly concludes about equivalent scalar IDs which could lead to
verifier bypass in privileged mode:
1. Prepare a 32-bit rogue number.
2. Put the rogue number into the upper half of a 64-bit register, and
roll a random (unknown to the verifier) bit in the lower half. The
rest of the bits should be zero (although variations are possible).
3. Assign an ID to the register by MOVing it to another arbitrary
register.
4. Perform a 32-bit spill of the register, then perform a 32-bit fill to
another register. Due to a bug in the verifier, the ID will be
preserved, although the new register will contain only the lower 32
bits, i.e. all zeros except one random bit.
At this point there are two registers with different values but the same
ID, which means the integrity of the verifier state has been corrupted.
5. Compare the new 32-bit register with 0. In the branch where it's
equal to 0, the verifier will believe that the original 64-bit
register is also 0, because it has the same ID, but its actual value
still contains the rogue number in the upper half.
Some optimizations of the verifier prevent the actual bypass, so
extra care is needed: the comparison must be between two registers,
and both branches must be reachable (this is why one random bit is
needed). Both branches are still suitable for the bypass.
6. Right shift the original register by 32 bits to pop the rogue number.
7. Use the rogue number as an offset with any pointer. The verifier will
believe that the offset is 0, while in reality it's the given number.
The fix is similar to the 32-bit BPF_MOV handling in check_alu_op for
SCALAR_VALUE. If the spill is narrowing the actual register value, don't
keep the ID, make sure it's reset to 0.
Fixes: 354e8f1970f8 ("bpf: Support <8-byte scalar spill and refill") Signed-off-by: Maxim Mikityanskiy <maxim@isovalent.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Tested-by: Andrii Nakryiko <andrii@kernel.org> # Checked veristat delta Acked-by: Yonghong Song <yhs@fb.com> Link: https://lore.kernel.org/bpf/20230607123951.558971-2-maxtram95@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
For aligned stack writes using BPF_ST instruction track stored values
in a same way BPF_STX is handled, e.g. make sure that the following
commands produce similar verifier knowledge:
fp[-8] = 42; r1 = 42;
fp[-8] = r1;
This covers two cases:
- non-null values written to stack are stored as spill of fake
registers;
- null values written to stack are stored as STACK_ZERO marks.
Previously both cases above used STACK_MISC marks instead.
Some verifier test cases relied on the old logic to obtain STACK_MISC
marks for some stack values. These test cases are updated in the same
commit to avoid failures during bisect.
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com> Link: https://lore.kernel.org/r/20230214232030.1502829-2-eddyz87@gmail.com Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Stable-dep-of: 713274f1f2c8 ("bpf: Fix verifier id tracking of scalars on spill") Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Restore the host's PMUSERENR_EL0 value instead of clearing it,
before returning back to userspace, as the host's EL0 might have
a direct access to PMU registers (some bits of PMUSERENR_EL0 for
might not be zero for the host EL0).
Fixes: 83a7a4d643d3 ("arm64: perf: Enable PMU counter userspace access for perf event") Signed-off-by: Reiji Watanabe <reijiw@google.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20230603025035.3781797-2-reijiw@google.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This change adds methods in the XFRM-I input path that ensures that
policies are checked prior to processing of the subsequent decapsulated
packet, after which the relevant policies may no longer be resolvable
(due to changing src/dst/proto/etc).
Notably, raw ESP/AH packets did not perform policy checks inherently,
whereas all other encapsulated packets (UDP, TCP encapsulated) do policy
checks after calling xfrm_input handling in the respective encapsulation
layer.
Fixes: b0355dbbf13c ("Fix XFRM-I support for nested ESP tunnels")
Test: Verified with additional Android Kernel Unit tests
Test: Verified against Android CTS Signed-off-by: Benedict Wong <benedictwong@google.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This change allows inbound traffic through nested IPsec tunnels to
successfully match policies and templates, while retaining the secpath
stack trace as necessary for netfilter policies.
Specifically, this patch marks secpath entries that have already matched
against a relevant policy as having been verified, allowing it to be
treated as optional and skipped after a tunnel decapsulation (during
which the src/dst/proto/etc may have changed, and the correct policy
chain no long be resolvable).
This approach is taken as opposed to the iteration in b0355dbbf13c,
where the secpath was cleared, since that breaks subsequent validations
that rely on the existence of the secpath entries (netfilter policies, or
transport-in-tunnel mode, where policies remain resolvable).
Fixes: b0355dbbf13c ("Fix XFRM-I support for nested ESP tunnels")
Test: Tested against Android Kernel Unit Tests
Test: Tested against Android CTS Signed-off-by: Benedict Wong <benedictwong@google.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The driver overrides the error codes and IRQ0 returned by platform_get_irq()
to -EINVAL, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the error
codes upstream. Since commit ce753ad1549c ("platform: finally disallow IRQ0
in platform_get_irq() and its ilk") IRQ0 is no longer returned by those APIs,
so we now can safely ignore it...
Ensure that file_seals is non-NULL before using it in the memfd_create()
syscall. One situation in which memfd_file_seals_ptr() could return a
NULL pointer when CONFIG_SHMEM=n, oopsing the kernel.
Link: https://lkml.kernel.org/r/20230607132427.2867435-1-roberto.sassu@huaweicloud.com Fixes: 47b9012ecdc7 ("shmem: add sealing support to hugetlb-backed memfd") Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com> Cc: Marc-Andr Lureau <marcandre.lureau@redhat.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
KPTI keeps around two PGDs: one for userspace and another for the
kernel. Among other things, set_pgd() contains infrastructure to
ensure that updates to the kernel PGD are reflected in the user PGD
as well.
One side-effect of this is that set_pgd() expects to be passed whole
pages. Unfortunately, init_trampoline_kaslr() passes in a single entry:
'trampoline_pgd_entry'.
When KPTI is on, set_pgd() will update 'trampoline_pgd_entry' (an
8-Byte globally stored [.bss] variable) and will then proceed to
replicate that value into the non-existent neighboring user page
(located +4k away), leading to the corruption of other global [.bss]
stored variables.
Fix it by directly assigning 'trampoline_pgd_entry' and avoiding
set_pgd().
[ dhansen: tweak subject and changelog ]
Fixes: 0925dda5962e ("x86/mm/KASLR: Use only one PUD entry for real mode trampoline") Suggested-by: Dave Hansen <dave.hansen@linux.intel.com> Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/all/20230614163859.924309-1-lee@kernel.org/g Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In a syzbot stress test that deliberately causes file system errors on
nilfs2 with a corrupted disk image, it has been reported that
nilfs_clear_dirty_page() called from nilfs_clear_dirty_pages() can cause a
general protection fault.
In nilfs_clear_dirty_pages(), when looking up dirty pages from the page
cache and calling nilfs_clear_dirty_page() for each dirty page/folio
retrieved, the back reference from the argument page to "mapping" may have
been changed to NULL (and possibly others). It is necessary to check this
after locking the page/folio.
So, fix this issue by not calling nilfs_clear_dirty_page() on a page/folio
after locking it in nilfs_clear_dirty_pages() if the back reference
"mapping" from the page/folio is different from the "mapping" that held
the page/folio just before.
The register and range mappings for the PCIe controller in Rockchip's
RK356x SoCs are incorrect. Replace them with corrected values from the
vendor BSP sources, updated to match current DT schema.
These values are also used in u-boot.
Fixes: 66b51ea7d70f ("arm64: dts: rockchip: Add rk3568 PCIe2x1 controller") Cc: stable@vger.kernel.org Signed-off-by: Andrew Powers-Holmes <aholmes@omnom.net> Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com> Tested-by: Diederik de Haas <didi.debian@cknow.org> Link: https://lore.kernel.org/r/20230601132516.153934-1-frattaroli.nicolas@gmail.com Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The max_raw_write member of the regmap_spi_avmm_bus structure is defined
as:
.max_raw_write = SPI_AVMM_VAL_SIZE * MAX_WRITE_CNT
SPI_AVMM_VAL_SIZE == 4 and MAX_WRITE_CNT == 1 so this results in a
maximum write transfer size of 4 bytes which provides only enough space to
transfer the address of the target register. It provides no space for the
value to be transferred. This bug became an issue (divide-by-zero in
_regmap_raw_write()) after the following was accepted into mainline:
commit 3981514180c9 ("regmap: Account for register length when chunking")
Change max_raw_write to include space (4 additional bytes) for both the
register address and value:
Now spi_geni_grab_gpi_chan() errors are correctly reported, the
-EPROBE_DEFER error should be returned from probe in case the
GPI dma driver is built as module and/or not probed yet.
Fixes: b59c122484ec ("spi: spi-geni-qcom: Add support for GPI dma") Fixes: 6532582c353f ("spi: spi-geni-qcom: fix error handling in spi_geni_grab_gpi_chan()") Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://lore.kernel.org/r/20230615-topic-sm8550-upstream-fix-spi-geni-qcom-probe-v2-1-670c3d9e8c9c@linaro.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When subprograms are in use, the main program is not jit'd after the
subprograms because jit_subprogs sets a value for prog->bpf_func upon
success. Subsequent calls to the JIT are bypassed when this value is
non-NULL. This leads to a situation where the main program and its
func[0] counterpart are both in the bpf kallsyms tree, but only func[0]
has an extable. Extables are only created during JIT. Now there are
two nearly identical program ksym entries in the tree, but only one has
an extable. Depending upon how the entries are placed, there's a chance
that a fault will call search_extable on the aux with the NULL entry.
Since jit_subprogs already copies state from func[0] to the main
program, include the extable pointer in this state duplication.
Additionally, ensure that the copy of the main program in func[0] is not
added to the bpf_prog_kallsyms table. Instead, let the main program get
added later in bpf_prog_load(). This ensures there is only a single
copy of the main program in the kallsyms table, and that its tag matches
the tag observed by tooling like bpftool.
Cc: stable@vger.kernel.org Fixes: 1c2a088a6626 ("bpf: x64: add JIT support for multi-function programs") Signed-off-by: Krister Johansen <kjlx@templeofstupid.com> Acked-by: Yonghong Song <yhs@fb.com> Acked-by: Ilya Leoshkevich <iii@linux.ibm.com> Tested-by: Ilya Leoshkevich <iii@linux.ibm.com> Link: https://lore.kernel.org/r/6de9b2f4b4724ef56efbb0339daaa66c8b68b1e7.1686616663.git.kjlx@templeofstupid.com Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The driver overrides the error codes and IRQ0 returned by platform_get_irq()
to -EINVAL, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the error
codes upstream. Since commit ce753ad1549c ("platform: finally disallow IRQ0
in platform_get_irq() and its ilk") IRQ0 is no longer returned by those APIs,
so we now can safely ignore it...
Fixes: 2408a08583d2 ("mmc: sunxi-mmc: Handle return value of platform_get_irq") Cc: stable@vger.kernel.org # v5.19+ Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru> Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com> Link: https://lore.kernel.org/r/20230617203622.6812-12-s.shtylyov@omp.ru Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The driver overrides the error codes and IRQ0 returned by platform_get_irq()
to -EINVAL, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the error
codes upstream. Since commit ce753ad1549c ("platform: finally disallow IRQ0
in platform_get_irq() and its ilk") IRQ0 is no longer returned by those APIs,
so we now can safely ignore it...
Fixes: 660fc733bd74 ("mmc: bcm2835: Add new driver for the sdhost controller.") Cc: stable@vger.kernel.org # v5.19+ Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru> Link: https://lore.kernel.org/r/20230617203622.6812-2-s.shtylyov@omp.ru Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The driver overrides the error codes and IRQ0 returned by platform_get_irq()
to -EINVAL, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the error
codes upstream. Since commit ce753ad1549c ("platform: finally disallow IRQ0
in platform_get_irq() and its ilk") IRQ0 is no longer returned by those APIs,
so we now can safely ignore it...
Fixes: 682798a596a6 ("mmc: sdhci-spear: Handle return value of platform_get_irq") Cc: stable@vger.kernel.org # v5.19+ Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20230617203622.6812-10-s.shtylyov@omp.ru Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The way that the timeout is currently calculated could lead to a u64
timeout value in mmci_start_command(). This value is then cast in a u32
register that leads to mmc erase failed issue with some SD cards.
The call to mmc_request_done() can schedule, so it must not be called
from irq context. Wake the irq thread if it needs to be called, and let
its existing logic do its work.
While SDHCI claims to support 64-bit DMA on MSM8916 it does not seem to
be properly functional. It is not immediately obvious because SDHCI is
usually used with IOMMU bypassed on this SoC, and all physical memory
has 32-bit addresses. But when trying to enable the IOMMU it quickly
fails with an error such as the following:
Looking closely it's obvious that only the 32-bit part of the address
(0xfffff200) arrives at the SMMU, the higher 16-bit (0xffff...) get
lost somewhere. This might not be a limitation of the SDHCI itself but
perhaps the bus/interconnect it is connected to, or even the connection
to the SMMU.
Work around this by setting SDHCI_QUIRK2_BROKEN_64_BIT_DMA to avoid
using 64-bit addresses.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20230518-msm8916-64bit-v1-1-5694b0f35211@gerhold.net Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
mmc host drivers should have enabled the asynchronous probe option, but
it seems like we didn't set it for litex_mmc when introducing litex mmc
support, so let's set it now.
Tested with linux-on-litex-vexriscv on sipeed tang nano 20K fpga.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org> Acked-by: Gabriel Somlo <gsomlo@gmail.com> Fixes: 92e099104729 ("mmc: Add driver for LiteX's LiteSDCard interface") Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20230617085319.2139-1-jszhang@kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
syzbot is again reporting circular locking dependency between
cpu_hotplug_lock and freezer_mutex. Do like what we did with
commit 57dcd64c7e036299 ("cgroup,freezer: hold cpu_hotplug_lock
before freezer_mutex").
Inside css_task_iter_start/next/end, css_set_lock is hold and then
released, so when iterating task(left side), the css_set may be moved to
another list(right side), then it->cset_head points to the old list head
and it->cset_pos->next points to the head node of new list, which can't
be used as struct css_set.
To fix this issue, switch from all css_sets to only scgrp's css_sets to
patch in-flight iterators to preserve correct iteration, and then
update it->cset_head as well.
An orphaned msk releases the used resources via the worker,
when the latter first see the msk in CLOSED status.
If the msk status transitions to TCP_CLOSE in the release callback
invoked by the worker's final release_sock(), such instance of the
workqueue will not take any action.
Additionally the MPTCP code prevents scheduling the worker once the
socket reaches the CLOSE status: such msk resources will be leaked.
The only code path that can trigger the above scenario is the
__mptcp_check_send_data_fin() in fallback mode.
Address the issue removing the special handling of fallback socket
in __mptcp_check_send_data_fin(), consolidating the state machine
for fallback and non fallback socket.
Since non-fallback sockets do not send and do not receive data_fin,
the mptcp code can update the msk internal status to match the next
step in the SM every time data fin (ack) should be generated or
received.
As a consequence we can remove a bunch of checks for fallback from
the fastpath.
Fixes: 6e628cd3a8f7 ("mptcp: use mptcp release_cb for delayed tasks") Cc: stable@vger.kernel.org Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Mat Martineau <martineau@kernel.org> Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
At passive MPJ time, if the msk socket lock is held by the user,
the new subflow is appended to the msk->join_list under the msk
data lock.
In mptcp_release_cb()/__mptcp_flush_join_list(), the subflows in
that list are moved from the join_list into the conn_list under the
msk socket lock.
Append and removal could race, possibly corrupting such list.
Address the issue splicing the join list into a temporary one while
still under the msk data lock.
Found by code inspection, the race itself should be almost impossible
to trigger in practice.
Fixes: 3e5014909b56 ("mptcp: cleanup MPJ subflow list handling") Cc: stable@vger.kernel.org Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
mptcp_recvmsg is allowed to release the msk socket lock when
blocking, and before re-acquiring it another thread could have
switched the sock to TCP_LISTEN status - with a prior
connect(AF_UNSPEC) - also clearing icsk_ack.rcv_mss.
Address the issue preventing the disconnect if some other process is
concurrently performing a blocking syscall on the same socket, alike
commit 4faeee0cf8a5 ("tcp: deny tcp_disconnect() when threads are waiting").
Fixes: a6b118febbab ("mptcp: add receive buffer auto-tuning") Cc: stable@vger.kernel.org Reported-by: Christoph Paasch <cpaasch@apple.com> Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/404 Signed-off-by: Paolo Abeni <pabeni@redhat.com> Tested-by: Christoph Paasch <cpaasch@apple.com> Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Currently the mptcp code has assumes that disconnect() can fail only
at mptcp_sendmsg_fastopen() time - to avoid a deadlock scenario - and
don't even bother returning an error code.
Soon mptcp_disconnect() will handle more error conditions: let's track
them explicitly.
As a bonus, explicitly annotate TCP-level disconnect as not failing:
the mptcp code never blocks for event on the subflows.
Fixes: 7d803344fdc3 ("mptcp: fix deadlock in fastopen error path") Cc: stable@vger.kernel.org Signed-off-by: Paolo Abeni <pabeni@redhat.com> Tested-by: Christoph Paasch <cpaasch@apple.com> Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
We cannot sanely handle partial retries for recvmsg if we have cmsg
attached. If we don't, then we'd just be overwriting the initial cmsg
header on retries. Alternatively we could increment and handle this
appropriately, but it doesn't seem worth the complication.
Move the MSG_WAITALL check into the non-multishot case while at it,
since MSG_WAITALL is explicitly disabled for multishot anyway.
Link: https://lore.kernel.org/io-uring/0b0d4411-c8fd-4272-770b-e030af6919a0@kernel.dk/ Cc: stable@vger.kernel.org # 5.10+ Reported-by: Stefan Metzmacher <metze@samba.org> Reviewed-by: Stefan Metzmacher <metze@samba.org> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In the case of fast device addition/removal, it's possible that
hv_eject_device_work() can start to run before create_root_hv_pci_bus()
starts to run; as a result, the pci_get_domain_bus_and_slot() in
hv_eject_device_work() can return a 'pdev' of NULL, and
hv_eject_device_work() can remove the 'hpdev', and immediately send a
message PCI_EJECTION_COMPLETE to the host, and the host immediately
unassigns the PCI device from the guest; meanwhile,
create_root_hv_pci_bus() and the PCI device driver can be probing the
dead PCI device and reporting timeout errors.
Fix the issue by adding a per-bus mutex 'state_lock' and grabbing the
mutex before powering on the PCI bus in hv_pci_enter_d0(): when
hv_eject_device_work() starts to run, it's able to find the 'pdev' and call
pci_stop_and_remove_bus_device(pdev): if the PCI device driver has
loaded, the PCI device driver's probe() function is already called in
create_root_hv_pci_bus() -> pci_bus_add_devices(), and now
hv_eject_device_work() -> pci_stop_and_remove_bus_device() is able
to call the PCI device driver's remove() function and remove the device
reliably; if the PCI device driver hasn't loaded yet, the function call
hv_eject_device_work() -> pci_stop_and_remove_bus_device() is able to
remove the PCI device reliably and the PCI device driver's probe()
function won't be called; if the PCI device driver's probe() is already
running (e.g., systemd-udev is loading the PCI device driver), it must
be holding the per-device lock, and after the probe() finishes and releases
the lock, hv_eject_device_work() -> pci_stop_and_remove_bus_device() is
able to proceed to remove the device reliably.
Fixes: 4daace0d8ce8 ("PCI: hv: Add paravirtual PCI front-end for Microsoft Hyper-V VMs") Signed-off-by: Dexuan Cui <decui@microsoft.com> Reviewed-by: Michael Kelley <mikelley@microsoft.com> Acked-by: Lorenzo Pieralisi <lpieralisi@kernel.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20230615044451.5580-6-decui@microsoft.com Signed-off-by: Wei Liu <wei.liu@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When the host tries to remove a PCI device, the host first sends a
PCI_EJECT message to the guest, and the guest is supposed to gracefully
remove the PCI device and send a PCI_EJECTION_COMPLETE message to the host;
the host then sends a VMBus message CHANNELMSG_RESCIND_CHANNELOFFER to
the guest (when the guest receives this message, the device is already
unassigned from the guest) and the guest can do some final cleanup work;
if the guest fails to respond to the PCI_EJECT message within one minute,
the host sends the VMBus message CHANNELMSG_RESCIND_CHANNELOFFER and
removes the PCI device forcibly.
In the case of fast device addition/removal, it's possible that the PCI
device driver is still configuring MSI-X interrupts when the guest receives
the PCI_EJECT message; the channel callback calls hv_pci_eject_device(),
which sets hpdev->state to hv_pcichild_ejecting, and schedules a work
hv_eject_device_work(); if the PCI device driver is calling
pci_alloc_irq_vectors() -> ... -> hv_compose_msi_msg(), we can break the
while loop in hv_compose_msi_msg() due to the updated hpdev->state, and
leave data->chip_data with its default value of NULL; later, when the PCI
device driver calls request_irq() -> ... -> hv_irq_unmask(), the guest
crashes in hv_arch_irq_unmask() due to data->chip_data being NULL.
Fix the issue by not testing hpdev->state in the while loop: when the
guest receives PCI_EJECT, the device is still assigned to the guest, and
the guest has one minute to finish the device removal gracefully. We don't
really need to (and we should not) test hpdev->state in the loop.
Fixes: de0aa7b2f97d ("PCI: hv: Fix 2 hang issues in hv_compose_msi_msg()") Signed-off-by: Dexuan Cui <decui@microsoft.com> Reviewed-by: Michael Kelley <mikelley@microsoft.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20230615044451.5580-3-decui@microsoft.com Signed-off-by: Wei Liu <wei.liu@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The statement "the hv_pci_bus_exit() call releases structures of all its
child devices" in commit d6af2ed29c7c is not true: in the path
hv_pci_probe() -> hv_pci_enter_d0() -> hv_pci_bus_exit(hdev, true): the
parameter "keep_devs" is true, so hv_pci_bus_exit() does *not* release the
child "struct hv_pci_dev *hpdev" that is created earlier in
pci_devices_present_work() -> new_pcichild_device().
The commit d6af2ed29c7c was originally made in July 2020 for RHEL 7.7,
where the old version of hv_pci_bus_exit() was used; when the commit was
rebased and merged into the upstream, people didn't notice that it's
not really necessary. The commit itself doesn't cause any issue, but it
makes hv_pci_probe() more complicated. Revert it to facilitate some
upcoming changes to hv_pci_probe().
Signed-off-by: Dexuan Cui <decui@microsoft.com> Reviewed-by: Michael Kelley <mikelley@microsoft.com> Acked-by: Wei Hu <weh@microsoft.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20230615044451.5580-5-decui@microsoft.com Signed-off-by: Wei Liu <wei.liu@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Since day 1 of the driver, there has been a race between
hv_pci_query_relations() and survey_child_resources(): during fast
device hotplug, hv_pci_query_relations() may error out due to
device-remove and the stack variable 'comp' is no longer valid;
however, pci_devices_present_work() -> survey_child_resources() ->
complete() may be running on another CPU and accessing the no-longer-valid
'comp'. Fix the race by flushing the workqueue before we exit from
hv_pci_query_relations().
Fixes: 4daace0d8ce8 ("PCI: hv: Add paravirtual PCI front-end for Microsoft Hyper-V VMs") Signed-off-by: Dexuan Cui <decui@microsoft.com> Reviewed-by: Michael Kelley <mikelley@microsoft.com> Acked-by: Lorenzo Pieralisi <lpieralisi@kernel.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20230615044451.5580-2-decui@microsoft.com Signed-off-by: Wei Liu <wei.liu@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
vmbus_wait_for_unload() may be called in the panic path after other
CPUs are stopped. vmbus_wait_for_unload() currently loops through
online CPUs looking for the UNLOAD response message. But the values of
CONFIG_KEXEC_CORE and crash_kexec_post_notifiers affect the path used
to stop the other CPUs, and in one of the paths the stopped CPUs
are removed from cpu_online_mask. This removal happens in both
x86/x64 and arm64 architectures. In such a case, vmbus_wait_for_unload()
only checks the panic'ing CPU, and misses the UNLOAD response message
except when the panic'ing CPU is CPU 0. vmbus_wait_for_unload()
eventually times out, but only after waiting 100 seconds.
Fix this by looping through *present* CPUs in vmbus_wait_for_unload().
The cpu_present_mask is not modified by stopping the other CPUs in the
panic path, nor should it be.
Also, in a CoCo VM the synic_message_page is not allocated in
hv_synic_alloc(), but is set and cleared in hv_synic_enable_regs()
and hv_synic_disable_regs() such that it is set only when the CPU is
online. If not all present CPUs are online when vmbus_wait_for_unload()
is called, the synic_message_page might be NULL. Add a check for this.
Fixes: cd95aad55793 ("Drivers: hv: vmbus: handle various crash scenarios") Cc: stable@vger.kernel.org Reported-by: John Starks <jostarks@microsoft.com> Signed-off-by: Michael Kelley <mikelley@microsoft.com> Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com> Link: https://lore.kernel.org/r/1684422832-38476-1-git-send-email-mikelley@microsoft.com Signed-off-by: Wei Liu <wei.liu@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Commit 572086325ce9 ("Drivers: hv: vmbus: Cleanup synic memory free path")
says "Any memory allocations that succeeded will be freed when the caller
cleans up by calling hv_synic_free()", but if the get_zeroed_page() in
hv_synic_alloc() fails, currently hv_synic_free() is not really called
in vmbus_bus_init(), consequently there will be a memory leak, e.g.
hv_context.hv_numa_map is not freed in the error path. Fix this by
updating the goto labels.
Cc: stable@kernel.org Signed-off-by: Dexuan Cui <decui@microsoft.com> Fixes: 4df4cb9e99f8 ("x86/hyperv: Initialize clockevents earlier in CPU onlining") Reviewed-by: Michael Kelley <mikelley@microsoft.com> Link: https://lore.kernel.org/r/20230504224155.10484-1-decui@microsoft.com Signed-off-by: Wei Liu <wei.liu@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
We run into guest hang in edk2 firmware when KSM is kept as running on
the host. The edk2 firmware is waiting for status 0x80 from QEMU's pflash
device (TYPE_PFLASH_CFI01) during the operation of sector erasing or
buffered write. The status is returned by reading the memory region of
the pflash device and the read request should have been forwarded to QEMU
and emulated by it. Unfortunately, the read request is covered by an
illegal stage2 mapping when the guest hang issue occurs. The read request
is completed with QEMU bypassed and wrong status is fetched. The edk2
firmware runs into an infinite loop with the wrong status.
The illegal stage2 mapping is populated due to same page sharing by KSM
at (C) even the associated memory slot has been marked as invalid at (B)
when the memory slot is requested to be deleted. It's notable that the
active and inactive memory slots can't be swapped when we're in the middle
of kvm_mmu_notifier_change_pte() because kvm->mn_active_invalidate_count
is elevated, and kvm_swap_active_memslots() will busy loop until it reaches
to zero again. Besides, the swapping from the active to the inactive memory
slots is also avoided by holding &kvm->srcu in __kvm_handle_hva_range(),
corresponding to synchronize_srcu_expedited() in kvm_swap_active_memslots().
Fix the issue by skipping the invalid memory slot at (C) to avoid the
illegal stage2 mapping so that the read request for the pflash's status
is forwarded to QEMU and emulated by it. In this way, the correct pflash's
status can be returned from QEMU to break the infinite loop in the edk2
firmware.
We tried a git-bisect and the first problematic commit is cd4c71835228 ("
KVM: arm64: Convert to the gfn-based MMU notifier callbacks"). With this,
clean_dcache_guest_page() is called after the memory slots are iterated
in kvm_mmu_notifier_change_pte(). clean_dcache_guest_page() is called
before the iteration on the memory slots before this commit. This change
literally enlarges the racy window between kvm_mmu_notifier_change_pte()
and memory slot removal so that we're able to reproduce the issue in a
practical test case. However, the issue exists since commit d5d8184d35c9
("KVM: ARM: Memory virtualization setup").
Cc: stable@vger.kernel.org # v3.9+ Fixes: d5d8184d35c9 ("KVM: ARM: Memory virtualization setup") Reported-by: Shuai Hu <hshuai@redhat.com> Reported-by: Zhenyu Zhang <zhenyzha@redhat.com> Signed-off-by: Gavin Shan <gshan@redhat.com> Reviewed-by: David Hildenbrand <david@redhat.com> Reviewed-by: Oliver Upton <oliver.upton@linux.dev> Reviewed-by: Peter Xu <peterx@redhat.com> Reviewed-by: Sean Christopherson <seanjc@google.com> Reviewed-by: Shaoqin Huang <shahuang@redhat.com>
Message-Id: <20230615054259.14911-1-gshan@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The addition of might_sleep() to down_timeout() caused the latter to
enable interrupts unconditionally in some cases, which in turn broke
the ACPI S3 wakeup path in acpi_suspend_enter(), where down_timeout()
is called by acpi_disable_all_gpes() via acpi_ut_acquire_mutex().
Namely, if CONFIG_DEBUG_ATOMIC_SLEEP is set, might_sleep() causes
might_resched() to be used and if CONFIG_PREEMPT_VOLUNTARY is set,
this triggers __cond_resched() which may call preempt_schedule_common(),
so __schedule() gets invoked and it ends up with enabled interrupts (in
the prev == next case).
Now, enabling interrupts early in the S3 wakeup path causes the kernel
to crash.
Address this by modifying acpi_suspend_enter() to disable GPEs without
attempting to acquire the sleeping lock which is not needed in that code
path anyway.
Fixes: 99409b935c9a ("locking/semaphore: Add might_sleep() to down_*() family") Reported-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: 5.15+ <stable@vger.kernel.org> # 5.15+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
As a result of analysis of a syzbot report, it turned out that in three
cases where nilfs2 allocates block device buffers directly via sb_getblk,
concurrent reads to the device can corrupt the allocated buffers.
Nilfs2 uses sb_getblk for segment summary blocks, that make up a log
header, and the super root block, that is the trailer, and when moving and
writing the second super block after fs resize.
In any of these, since the uptodate flag is not set when storing metadata
to be written in the allocated buffers, the stored metadata will be
overwritten if a device read of the same block occurs concurrently before
the write. This causes metadata corruption and misbehavior in the log
write itself, causing warnings in nilfs_btree_assign() as reported.
Fix these issues by setting an uptodate flag on the buffer head on the
first or before modifying each buffer obtained with sb_getblk, and
clearing the flag on failure.
When setting the uptodate flag, the lock_buffer/unlock_buffer pair is used
to perform necessary exclusive control, and the buffer is filled to ensure
that uninitialized bytes are not mixed into the data read from others. As
for buffers for segment summary blocks, they are filled incrementally, so
if the uptodate flag was unset on their allocation, set the flag and zero
fill the buffer once at that point.
Also, regarding the superblock move routine, the starting point of the
memset call to zerofill the block is incorrectly specified, which can
cause a buffer overflow on file systems with block sizes greater than
4KiB. In addition, if the superblock is moved within a large block, it is
necessary to assume the possibility that the data in the superblock will
be destroyed by zero-filling before copying. So fix these potential
issues as well.
When commit 19343b5bdd16 ("mm/page-writeback: introduce tracepoint for
wait_on_page_writeback()") repurposed the writeback_dirty_page trace event
as a template to create its new wait_on_page_writeback trace event, it
ended up opening a window to NULL pointer dereference crashes due to the
(infrequent) occurrence of a race where an access to a page in the
swap-cache happens concurrently with the moment this page is being written
to disk and the tracepoint is enabled:
This problem arises from the fact that the repurposed writeback_dirty_page
trace event code was written assuming that every pointer to mapping
(struct address_space) would come from a file-mapped page-cache object,
thus mapping->host would always be populated, and that was a valid case
before commit 19343b5bdd16. The swap-cache address space
(swapper_spaces), however, doesn't populate its ->host (struct inode)
pointer, thus leading to the crashes in the corner-case aforementioned.
commit 19343b5bdd16 ended up breaking the assignment of __entry->name and
__entry->ino for the wait_on_page_writeback tracepoint -- both dependent
on mapping->host carrying a pointer to a valid inode. The assignment of
__entry->name was fixed by commit 68f23b89067f ("memcg: fix a crash in
wb_workfn when a device disappears"), and this commit fixes the remaining
case, for __entry->ino.
Link: https://lkml.kernel.org/r/20230606233613.1290819-1-aquini@redhat.com Fixes: 19343b5bdd16 ("mm/page-writeback: introduce tracepoint for wait_on_page_writeback()") Signed-off-by: Rafael Aquini <aquini@redhat.com> Reviewed-by: Yafang Shao <laoar.shao@gmail.com> Cc: Aristeu Rozanski <aris@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
It was not working because the commit ad3493746ebe ("selftests: mptcp:
add test-cases for mixed v4/v6 subflows") is not in v6.1. This commit
changes how the connections are being created in mptcp_join.sh selftest:
with IPv6 support always enabled. But then in v6.1, the server still
create IPv4 only connections, so without the v4-mapped-v6 format with
the "::ffff:" prefix like we have in v6.3.
The modification here adds a support for connections created in v4 as
well so it fixes the issue in v6.1. This patch is not needed for the
selftests in v6.3 because only IPv6 listening sockets are being created.
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
One of them is the support of the MP_FAIL / infinite mapping introduced
by commit 1e39e5a32ad7 ("mptcp: infinite mapping sending") and the
following ones.
It is possible to look for one of the infinite mapping counters to know
in advance if the this feature is available.
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
One of them is the support of the userspace PM introduced by commit 4638de5aefe5 ("mptcp: handle local addrs announced by userspace PMs")
and the following ones.
It is possible to look for the MPTCP pm_type's sysctl knob to know in
advance if the userspace PM is available.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368 Fixes: 5ac1d2d63451 ("selftests: mptcp: Add tests for userspace PM type") Cc: stable@vger.kernel.org Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
Some tests are using IPTables and/or TC commands to force some
behaviours. If one of these commands fails -- likely because some
features are not available due to missing kernel config -- we should
intercept the error and skip the tests requiring these features.
Note that if we expect to have these features available and if
SELFTESTS_MPTCP_LIB_EXPECT_ALL_FEATURES env var is set to 1, the tests
will be marked as failed instead of skipped.
This patch also replaces the 'exit 1' by 'return 1' not to stop the
selftest in the middle without the conclusion if there is an issue with
NF or TC.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368 Fixes: 8d014eaa9254 ("selftests: mptcp: add ADD_ADDR timeout test case") Cc: stable@vger.kernel.org Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
One of them is TCP_INQ cmsg support introduced in commit 2c9e77659a0c
("mptcp: add TCP_INQ cmsg support").
It is possible to look for "mptcp_ioctl" in kallsyms because it was
needed to introduce the mentioned feature. We can skip these tests and
not set TCPINQ option if the feature is not supported.
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
One of them is the listen diag dump support introduced by
commit 4fa39b701ce9 ("mptcp: listen diag dump support").
It looks like there is no good pre-check to do here, i.e. dedicated
function available in kallsyms. Instead, we try to get info if nothing
is returned, the test is marked as skipped.
That's not ideal because something could be wrong with the feature and
instead of reporting an error, the test could be marked as skipped. If
we know in advanced that the feature is supposed to be supported, the
tester can set SELFTESTS_MPTCP_LIB_EXPECT_ALL_FEATURES env var to 1: in
this case the test will report an error instead of marking the test as
skipped if nothing is returned.
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
One of them is the support of sending an MP_PRIO signal for the initial
subflow, introduced by commit c157bbe776b7 ("mptcp: allow the in kernel
PM to set MPC subflow priority").
It is possible to look for "mptcp_subflow_send_ack" in kallsyms because
it was needed to introduce the mentioned feature. So we can know in
advance if the feature is supported instead of trying and accepting any
results.
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
One of them is the support of the fullmesh flag for the in-kernel PM
introduced by commit 2843ff6f36db ("mptcp: remote addresses fullmesh")
and commit 1a0d6136c5f0 ("mptcp: local addresses fullmesh").
It looks like there is no easy external sign we can use to predict the
expected behaviour. We could add the flag and then check if it has been
added but for that, and for each fullmesh test, we would need to setup a
new environment, do the checks, clean it and then only start the test
from yet another clean environment. To keep it simple and avoid
introducing new issues, we look for a specific kernel version. That's
not ideal but an acceptable solution for this case.
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
Commit bccefb762439 ("selftests: mptcp: simplify pm_nl_change_endpoint")
has simplified the way the backup flag is set on an endpoint. Instead of
doing:
./pm_nl_ctl set 10.0.2.1 flags backup
Now we do:
./pm_nl_ctl set id 1 flags backup
The new way is easier to maintain but it is also incompatible with older
kernels not supporting the implicit endpoints putting in place the
infrastructure to set flags per ID, hence the second Fixes tag.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368 Fixes: bccefb762439 ("selftests: mptcp: simplify pm_nl_change_endpoint") Cc: stable@vger.kernel.org Fixes: 4cf86ae84c71 ("mptcp: strict local address ID selection") Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
One of them is the support of the implicit endpoints introduced by
commit d045b9eb95a9 ("mptcp: introduce implicit endpoints").
It is possible to look for "mptcp_subflow_send_ack" in kallsyms because
it was needed to introduce the mentioned feature. So we can know in
advance if the feature is supported instead of trying and accepting any
results.
Note that here and in the following commits, we re-do the same check for
each sub-test of the same function for a few reasons. The main one is
not to break the ID assign to each test in order to be able to easily
compare results between different kernel versions. Also, we can still
run a specific test even if it is skipped. Another reason is that it
makes it clear during the review that a specific subtest will be skipped
or not under certain conditions. At the end, it looks OK to call the
exact same helper multiple times: it is not a critical path and it is
the same code that is executed, not really more cases to maintain.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368 Fixes: 69c6ce7b6eca ("selftests: mptcp: add implicit endpoint test case") Cc: stable@vger.kernel.org Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
At some points, a new feature caused internal behaviour changes we are
verifying in the selftests, see the Fixes tag below. It was not a UAPI
change but because in these selftests, we check some internal
behaviours, it is normal we have to adapt them from time to time after
having added some features.
It looks like there is no external sign we can use to predict the
expected behaviour. Instead of accepting different behaviours and thus
not really checking for the expected behaviour, we are looking here for
a specific kernel version. That's not ideal but it looks better than
removing the test because it cannot support older kernel versions.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368 Fixes: 6fa0174a7c86 ("mptcp: more careful RM_ADDR generation") Cc: stable@vger.kernel.org Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
One of them is the support of MP_FASTCLOSE introduced in commit f284c0c77321 ("mptcp: implement fastclose xmit path").
If the MIB counter is not available, the test cannot be verified and the
behaviour will not be the expected one. So we can skip the test if the
counter is missing.
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
At some points, a new feature caused internal behaviour changes we are
verifying in the selftests, see the Fixes tag below. It was not a uAPI
change but because in these selftests, we check some internal
behaviours, it is normal we have to adapt them from time to time after
having added some features.
It is possible to look for "mptcp_pm_subflow_check_next" in kallsyms
because it was needed to introduce the mentioned feature. So we can know
in advance what the behaviour we are expecting here instead of
supporting the two behaviours.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368 Fixes: 86e39e04482b ("mptcp: keep track of local endpoint still available for each msk") Cc: stable@vger.kernel.org Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
One of them is the MPTCP MIB counters introduced in commit fc518953bc9c
("mptcp: add and use MIB counter infrastructure") and more later. The
MPTCP Join selftest heavily relies on these counters.
If a counter is not supported by the kernel, it is not displayed when
using 'nstat -z'. We can then detect that and skip the verification. A
new helper (get_counter()) has been added to do the required checks and
return an error if the counter is not available.
Note that if we expect to have these features available and if
SELFTESTS_MPTCP_LIB_EXPECT_ALL_FEATURES env var is set to 1, the tests
will be marked as failed instead of skipped.
This new helper also makes sure we get the exact counter we want to
avoid issues we had in the past, e.g. with MPTcpExtRmAddr and
MPTcpExtRmAddrDrop sharing the same prefix. While at it, we uniform the
way we fetch a MIB counter.
Note for the backports: we rarely change these modified blocks so if
there is are conflicts, it is very likely because a counter is not used
in the older kernels and we don't need that chunk.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368 Fixes: b08fbf241064 ("selftests: add test-cases for MPTCP MP_JOIN") Cc: stable@vger.kernel.org Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
Here are some helpers that will be used to mark subtests as skipped if a
feature is not supported. Marking as a fix for the commit introducing
this selftest to help with the backports.
While at it, also check if kallsyms feature is available as it will also
be used in the following commits to check if MPTCP features are
available before starting a test.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368 Fixes: b08fbf241064 ("selftests: add test-cases for MPTCP MP_JOIN") Cc: stable@vger.kernel.org Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
A new function is now available to easily detect if a feature is
missing by looking at the kernel version. That's clearly not ideal and
this kind of check should be avoided as soon as possible. But sometimes,
there are no external sign that a "feature" is available or not:
internal behaviours can change without modifying the uAPI and these
selftests are verifying the internal behaviours. Sometimes, the only
(easy) way to verify if the feature is present is to run the test but
then the validation cannot determine if there is a failure with the
feature or if the feature is missing. Then it looks better to check the
kernel version instead of having tests that can never fail. In any case,
we need a solution not to have a whole selftest being marked as failed
just because one sub-test has failed.
Note that this env var car be set to 1 not to do such check and run the
linked sub-test: SELFTESTS_MPTCP_LIB_NO_KVERSION_CHECK.
This new helper is going to be used in the following commits. In order
to ease the backport of such future patches, it would be good if this
patch is backported up to the introduction of MPTCP selftests, hence the
Fixes tag below: this type of check was supposed to be done from the
beginning.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368 Fixes: 048d19d444be ("mptcp: add basic kselftest for mptcp") Cc: stable@vger.kernel.org Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
One of them is the getsockopt(SOL_MPTCP) to get info about the MPTCP
connections introduced by commit 55c42fa7fa33 ("mptcp: add MPTCP_INFO
getsockopt") and the following ones.
It is possible to look for "mptcp_diag_fill_info" in kallsyms because
it is introduced by the mentioned feature. So we can know in advance if
the feature is supported and skip the sub-test if not.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368 Fixes: ce9979129a0b ("selftests: mptcp: add mptcp getsockopt test cases") Cc: stable@vger.kernel.org Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
One of them is the getsockopt(SOL_MPTCP) to get info about the MPTCP
connections introduced by commit 55c42fa7fa33 ("mptcp: add MPTCP_INFO
getsockopt") and the following ones.
We cannot guess in advance which sizes the kernel will returned: older
kernel can returned smaller sizes, e.g. recently the tcp_info structure
has been modified in commit 71fc704768f6 ("tcp: add rcv_wnd and
plb_rehash to TCP_INFO") where a new field has been added.
The userspace can also expect a smaller size if it is compiled with old
uAPI kernel headers.
So for these sizes, we can only check if they are above a certain
threshold, 0 for the moment. We can also only compared sizes with the
ones set by the kernel.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368 Fixes: ce9979129a0b ("selftests: mptcp: add mptcp getsockopt test cases") Cc: stable@vger.kernel.org Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
One of them is the fullmesh flag that can be given to the MPTCP
in-kernel path-manager and introduced in commit 2843ff6f36db ("mptcp:
remote addresses fullmesh").
If the flag is not visible in the dump after having set it, we don't
check the content. Note that if we expect to have this feature and
SELFTESTS_MPTCP_LIB_EXPECT_ALL_FEATURES env var is set to 1, we always
check the content to avoid regressions.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368 Fixes: 6da1dfdd037e ("selftests: mptcp: add set_flags tests in pm_netlink.sh") Cc: stable@vger.kernel.org Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
One of them is the checks of the default limits returned by the MPTCP
in-kernel path-manager. The default values have been modified by commit 72bcbc46a5c3 ("mptcp: increase default max additional subflows to 2").
Instead of comparing with hardcoded values, we can get the default one
and compare with them.
Note that if we expect to have the latest version, we continue to check
the hardcoded values to avoid unexpected behaviour changes.
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
One of them is the support of IP(V6)_TRANSPARENT socket option with
MPTCP connections introduced by commit c9406a23c116 ("mptcp: sockopt:
add SOL_IP freebind & transparent options").
It is possible to look for "__ip_sock_set_tos" in kallsyms because
IP(V6)_TRANSPARENT socket option support has been added after TOS
support which came with the required infrastructure in MPTCP sockopt
code. To support TOS, the following function has been exported (T). Not
great but better than checking for a specific kernel version.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368 Fixes: 5fb62e9cd3ad ("selftests: mptcp: add tproxy test case") Cc: stable@vger.kernel.org Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
New functions are now available to easily detect if a certain feature is
missing by looking at kallsyms.
These new helpers are going to be used in the following commits. In
order to ease the backport of such future patches, it would be good if
this patch is backported up to the introduction of MPTCP selftests,
hence the Fixes tag below: this type of check was supposed to be done
from the beginning.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368 Fixes: 048d19d444be ("mptcp: add basic kselftest for mptcp") Cc: stable@vger.kernel.org Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Most of the code had an issue according to ShellCheck.
That's mainly due to the fact it incorrectly believes most of the code
was unreachable because it's invoked by variable name, see how the
"tests" array is used.
Once SC2317 has been ignored, three small warnings were still visible:
- SC2155: Declare and assign separately to avoid masking return values.
- SC2046: Quote this to prevent word splitting: can be ignored because
"ip netns pids" can display more than one pid.
- SC2166: Prefer [ p ] || [ q ] as [ p -o q ] is not well defined.
This probably didn't fix any actual issues but it might help spotting
new interesting warnings reported by ShellCheck as just before,
ShellCheck was reporting issues for most lines making it a bit useless.
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
mptcp_connect tool was printing some duplicated entries when showing how
to use it: -j -l -r
While at it, I also:
- moved the very few entries that were not sorted,
- added -R that was missing since
commit 8a4b910d005d ("mptcp: selftests: add rcvbuf set option"),
- removed the -u parameter that has been removed in
commit f730b65c9d85 ("selftests: mptcp: try to set mptcp ulp mode in different sk states").
No need to backport this, it is just an internal tool used by our
selftests. The help menu is mainly useful for MPTCP kernel devs.
Acked-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The tick period is aligned very early while the first clock_event_device is
registered. At that point the system runs in periodic mode and switches
later to one-shot mode if possible.
The next wake-up event is programmed based on the aligned value
(tick_next_period) but the delta value, that is used to program the
clock_event_device, is computed based on ktime_get().
With the subtracted offset, the device fires earlier than the exact time
frame. With a large enough offset the system programs the timer for the
next wake-up and the remaining time left is too small to make any boot
progress. The system hangs.
Move the alignment later to the setup of tick_sched timer. At this point
the system switches to oneshot mode and a high resolution clocksource is
available. At this point it is safe to align tick_next_period because
ktime_get() will now return accurate (not jiffies based) time.
[bigeasy: Patch description + testing].
Fixes: e9523a0d81899 ("tick/common: Align tick period with the HZ tick.") Reported-by: Mathias Krause <minipli@grsecurity.net> Reported-by: "Bhatnagar, Rishabh" <risbhat@amazon.com> Suggested-by: Mathias Krause <minipli@grsecurity.net> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Richard W.M. Jones <rjones@redhat.com> Tested-by: Mathias Krause <minipli@grsecurity.net> Acked-by: SeongJae Park <sj@kernel.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/5a56290d-806e-b9a5-f37c-f21958b5a8c0@grsecurity.net Link: https://lore.kernel.org/12c6f9a3-d087-b824-0d05-0d18c9bc1bf3@amazon.com Link: https://lore.kernel.org/r/20230615091830.RxMV2xf_@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This patch validate session id and tree id in compound request.
If first operation in the compound is SMB2 ECHO request, ksmbd bypass
session and tree validation. So work->sess and work->tcon could be NULL.
If secound request in the compound access work->sess or tcon, It cause
NULL pointer dereferecing error.
Cc: stable@vger.kernel.org Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-21165 Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
ksmbd_smb2_check_message doesn't validate hdr->NextCommand. If
->NextCommand is bigger than Offset + Length of smb2 write, It will
allow oversized smb2 write length. It will cause OOB read in smb2_write.
Cc: stable@vger.kernel.org Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-21164 Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
->StructureSize2 indicates command payload size. ksmbd should validate
this size with rfc1002 length before accessing it.
This patch remove unneeded check and add the validation for this.
Pluton is an integrated security processor present in some recent Ryzen
parts. If it's enabled, it presents two devices - an MSFT0101 ACPI device
that's broadly an implementation of a Command Response Buffer TPM2, and an
MSFT0200 ACPI device whose functionality I haven't examined in detail yet.
This patch only attempts to add support for the TPM device.
There's a few things that need to be handled here. The first is that the
TPM2 ACPI table uses a previously undefined start method identifier. The
table format appears to include 16 bytes of startup data, which corresponds
to one 64-bit address for a start message and one 64-bit address for a
completion response. The second is that the ACPI tables on the Thinkpad Z13
I'm testing this on don't define any memory windows in _CRS (or, more
accurately, there are two empty memory windows). This check doesn't seem
strictly necessary, so I've skipped that.
Finally, it seems like chip needs to be explicitly asked to transition into
ready status on every command. Failing to do this means that if two
commands are sent in succession without an idle/ready transition in
between, everything will appear to work fine but the response is simply the
original command. I'm working without any docs here, so I'm not sure if
this is actually the required behaviour or if I'm missing something
somewhere else, but doing this results in the chip working reliably.
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Matthew Garrett <mjg59@srcf.ucam.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Cc: "Limonciello, Mario" <mario.limonciello@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Writing the TPM_INT_STATUS register in the interrupt handler to clear the
interrupts only has effect if a locality is held. Since this is not
guaranteed at the time the interrupt is fired, claim the locality
explicitly in the handler.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com> Tested-by: Michael Niewöhner <linux@mniewoehner.de> Tested-by: Jarkko Sakkinen <jarkko@kernel.org> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
There are several issues with copy_from_user_nofault():
- access_ok() is designed for user context only and for that reason
it has WARN_ON_IN_IRQ() which triggers when bpf, kprobe, eprobe
and perf on ppc are calling it from irq.
- it's missing nmi_uaccess_okay() which is a nop on all architectures
except x86 where it's required.
The comment in arch/x86/mm/tlb.c explains the details why it's necessary.
Calling copy_from_user_nofault() from bpf, [ke]probe without this check is not safe.
- __copy_from_user_inatomic() under CONFIG_HARDENED_USERCOPY is calling
check_object_size()->__check_object_size()->check_heap_object()->find_vmap_area()->spin_lock()
which is not safe to do from bpf, [ke]probe and perf due to potential deadlock.
Fix all three issues. At the end the copy_from_user_nofault() becomes
equivalent to copy_from_user_nmi() from safety point of view with
a difference in the return value.
LS1028A is using DMA with LPUART. Having RX watermark set to 1, means
DMA transactions are started only after receiving the second character.
On other platforms with newer LPUART IP, Receiver Idle Empty function
initiates the DMA request after the receiver is idling for 4 characters.
But this feature is missing on LS1028A, which is causing a 1-character
delay in the RX direction on this platform.
Set RX watermark to 0 to initiate RX DMA after each character.
Link: https://lore.kernel.org/linux-serial/20230607103459.1222426-1-robert.hodaszi@digi.com/ Fixes: 9ad9df844754 ("tty: serial: fsl_lpuart: Fix the wrong RXWATER setting for rx dma case") Cc: stable <stable@kernel.org> Signed-off-by: Robert Hodaszi <robert.hodaszi@digi.com>
Message-ID: <20230609121334.1878626-1-robert.hodaszi@digi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
[Why]
When the PSR enabled. If you try to adjust the timing parameters,
it may cause system hang. Because the timing mismatch with the
DMCUB settings.
[How]
Disable the PSR before adjusting timing parameters.
Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Acked-by: Stylon Wang <stylon.wang@amd.com> Signed-off-by: Tom Chung <chiahsuan.chung@amd.com> Reviewed-by: Wayne Lin <Wayne.Lin@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
[Why & How]
This commit is part of a sequence of changes that replaces the commit
sequence used in the DC with a new one. As a result of this transition,
we moved some specific parts from the commit sequence and brought them
to amdgpu_dm. This commit adds a wrapper inside DM that enable our
drivers to do any necessary preparation or change before we offload the
plane/stream update to DC.
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com> Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com> Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stable-dep-of: ea2062dd1f03 ("drm/amd/display: fix the system hang while disable PSR") Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
[Why & How]
The old dc_commit_updates_for_stream lacks manipulation for many corner
cases where the DC feature requires special attention; as a result, it
starts to show its limitation (e.g., the SubVP feature is not supported
by it, among other cases). To modernize and unify our internal API, this
commit replaces the old dc_commit_updates_for_stream with
dc_update_planes_and_stream, which has more features.
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com> Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com> Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stable-dep-of: ea2062dd1f03 ("drm/amd/display: fix the system hang while disable PSR") Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Kamal Mostafa [Fri, 1 Sep 2023 17:22:01 +0000 (10:22 -0700)]
UBUNTU: Upstream stable to v6.1.35, v6.3.9
BugLink: https://bugs.launchpad.net/bugs/2033931 Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
As noted by Michal, the blkg_iostat_set's in the lockless list hold
reference to blkg's to protect against their removal. Those blkg's
hold reference to blkcg. When a cgroup is being destroyed,
cgroup_rstat_flush() is only called at css_release_work_fn() which
is called when the blkcg reference count reaches 0. This circular
dependency will prevent blkcg and some blkgs from being freed after
they are made offline.
It is less a problem if the cgroup to be destroyed also has other
controllers like memory that will call cgroup_rstat_flush() which will
clean up the reference count. If block is the only controller that uses
rstat, these offline blkcg and blkgs may never be freed leaking more
and more memory over time.
To prevent this potential memory leak:
- flush blkcg per-cpu stats list in __blkg_release(), when no new stat
can be added
- add global blkg_stat_lock for covering concurrent parent blkg stat
update
- don't grab bio->bi_blkg reference when adding the stats into blkcg's
per-cpu stat list since all stats are guaranteed to be consumed before
releasing blkg instance, and grabbing blkg reference for stats was the
most fragile part of original patch
A recent patch replaced a tasklet execution of cq->comp_handler by a
direct call. While this made sense it let changes to cq->notify state be
unprotected and assumed that the cq completion machinery and the ulp done
callbacks were reentrant. The result is that in some cases completion
events can be lost. This patch moves the cq->comp_handler call inside of
the spinlock in rxe_cq_post which solves both issues. This is compatible
with the matching code in the request notify verb.
Fixes: 78b26a335310 ("RDMA/rxe: Remove tasklet call from rxe_cq.c") Link: https://lore.kernel.org/r/20230612155032.17036-1-rpearsonhpe@gmail.com Signed-off-by: Bob Pearson <rpearsonhpe@gmail.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>