After commit 92923ca3aacef63c92d ("mm: meminit: only set page reserved
in the memblock region"), the MIPS hibernation is broken. Because pages
in nosave data section should be "reserved", but currently they aren't
set to "reserved" at initialization. This patch makes hibernation work
again.
This makes the ath79 bootconsole behave the same way as the generic 8250
bootconsole.
Also waiting for TEMT (transmit buffer is empty) instead of just THRE
(transmit buffer is not full) ensures that all characters have been
transmitted before the real serial driver starts reconfiguring the serial
controller (which would sometimes result in garbage being transmitted.)
This change does not cause a visible performance loss.
In addition, this seems to fix a hang observed in certain configurations on
many AR7xxx/AR9xxx SoCs during autoconfig of the real serial driver.
A more complete follow-up patch will disable 8250 autoconfig for ath79
altogether (the serial controller is detected as a 16550A, which is not
fully compatible with the ath79 serial, and the autoconfig may lead to
undefined behavior on ath79.)
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
It's possible for pages to become visible prior to update_mmu_cache
running if a thread within the same address space preempts the current
thread or runs simultaneously on another CPU. That is, the following
scenario is possible:
CPU0 CPU1
write to page
flush_dcache_page
flush_icache_page
set_pte_at
map page
update_mmu_cache
If CPU1 maps the page in between CPU0's set_pte_at, which marks it valid
& visible, and update_mmu_cache where the dcache flush occurs then CPU1s
icache will fill from stale data (unless it fills from the dcache, in
which case all is good, but most MIPS CPUs don't have this property).
Commit 4d46a67a3eb8 ("MIPS: Fix race condition in lazy cache flushing.")
attempted to fix that by performing the dcache flush in
flush_icache_page such that it occurs before the set_pte_at call makes
the page visible. However it has the problem that not all code that
writes to pages exposed to userland call flush_icache_page. There are
many callers of set_pte_at under mm/ and only 2 of them do call
flush_icache_page. Thus the race window between a page becoming visible
& being coherent between the icache & dcache remains open in some cases.
To illustrate some of the cases, a WARN was added to __update_cache with
this patch applied that triggered in cases where a page about to be
flushed from the dcache was not the last page provided to
flush_icache_page. That is, backtraces were obtained for cases in which
the race window is left open without this patch. The 2 standout examples
follow.
These code paths write into a page, call flush_dcache_page then call
set_pte_at without flush_icache_page inbetween. The end result is that
the icache can become corrupted & userland processes may execute
unexpected or invalid code, typically resulting in a reserved
instruction exception, a trap or a segfault.
Fix this race condition fully by performing any cache maintenance
required to keep the icache & dcache in sync in set_pte_at, before the
page is made valid. This has the added bonus of ensuring the cache
maintenance always happens in one location, rather than being duplicated
in flush_icache_page & update_mmu_cache. It also matches the way other
architectures solve the same problem (see arm, ia64 & powerpc).
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Reported-by: Ionela Voinescu <ionela.voinescu@imgtec.com> Cc: Lars Persson <lars.persson@axis.com> Fixes: 4d46a67a3eb8 ("MIPS: Fix race condition in lazy cache flushing.") Cc: Steven J. Hill <sjhill@realitydiluted.com> Cc: David Daney <david.daney@cavium.com> Cc: Huacai Chen <chenhc@lemote.com> Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Jerome Marchand <jmarchan@redhat.com> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12722/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
The following patch will expose __update_cache to highmem pages. Handle
them by mapping them in for the duration of the cache maintenance, just
like in __flush_dcache_page. The code for that isn't shared because we
need the page address in __update_cache so sharing became messy. Given
that the entirity is an extra 5 lines, just duplicate it.
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: Lars Persson <lars.persson@axis.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Jerome Marchand <jmarchan@redhat.com> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12721/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
When flush_dcache_page is called on an executable page, that page is
about to be provided to userland & we can presume that the icache
contains no valid entries for its address range. However if the icache
does not fill from the dcache then we cannot presume that the pages
content has been written back as far as the memories that the dcache
will fill from (ie. L2 or further out).
This was being done for lowmem pages, but not for highmem which can lead
to icache corruption. Fix this by mapping highmem pages & flushing their
content from the dcache in __flush_dcache_page before providing the page
to userland, just as is done for lowmem pages.
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: Lars Persson <lars.persson@axis.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12720/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Commit f51246efee2b ("MIPS: Get rid of finish_arch_switch().") moved the
__restore_watch() call from finish_arch_switch() (i.e. after resume()
returns) to before the resume() call in switch_to(). This results in
watchpoints only being restored when a task is descheduled, preventing
the watchpoints from being effective most of the time, except due to
chance before the watchpoints are lazily removed.
Fix the call sequence from switch_to() through to
mips_install_watch_registers() to pass the task_struct pointer of the
next task, instead of using current. This allows the watchpoints for the
next (non-current) task to be restored without reintroducing
finish_arch_switch().
Fixes: f51246efee2b ("MIPS: Get rid of finish_arch_switch().") Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12726/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Since commit 8cb48fe169dd ("MIPS: Provide correct siginfo_t.si_stime"),
MIPS' uapi/asm/siginfo.h has included uapi/asm-generic/siginfo.h
directly before defining MIPS' struct siginfo, in order to get the
necessary definitions needed for the siginfo struct without the generic
copy_siginfo() hitting compiler errors due to struct siginfo not yet
being defined.
Now that the generic copy_siginfo() is moved out to linux/signal.h we
can safely include asm-generic/siginfo.h before defining the MIPS
specific struct siginfo, which avoids the uapi/ include as well as
breakage due to generic copy_siginfo() being defined before struct
siginfo.
Reported-by: Christopher Ferris <cferris@google.com> Fixes: 8cb48fe169dd ("MIPS: Provide correct siginfo_t.si_stime") Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Petr Malat <oss@malat.biz> Cc: linux-mips@linux-mips.org Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Commit 85efde6f4e0d ("make exported headers use strict posix types")
changed the asm-generic siginfo.h to use the __kernel_* types, and
commit 3a471cbc081b ("remove __KERNEL_STRICT_NAMES") make the internal
types accessible only to the kernel, but the MIPS implementation hasn't
been updated to match.
Switch to proper types now so that the exported asm/siginfo.h won't
produce quite so many compiler errors when included alone by a user
program.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Christopher Ferris <cferris@google.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12477/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
When showing backtraces in response to traps, for example crashes and
address errors (usually unaligned accesses) when they are set in debugfs
to be reported, unwind_stack will be used if the PC was in the kernel
text address range. However since EVA it is possible for user and kernel
address ranges to overlap, and even without EVA userland can still
trigger an address error by jumping to a KSeg0 address.
Adjust the check to also ensure that it was running in kernel mode. I
don't believe any harm can come of this problem, since unwind_stack() is
sufficiently defensive, however it is only meant for unwinding kernel
code, so to be correct it should use the raw backtracing instead.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Reviewed-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11701/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
(cherry picked from commit d2941a975ac745c607dfb590e92bb30bc352dad9) Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
When unwinding through IRQs and exceptions, the unwinding only continues
if the PC is a kernel text address, however since EVA it is possible for
user and kernel address ranges to overlap, potentially allowing
unwinding to continue to user mode if the user PC happens to be in the
kernel text address range.
Adjust the check to also ensure that the register state from before the
exception is actually running in kernel mode, i.e. !user_mode(regs).
I don't believe any harm can come of this problem, since the PC is only
output, the stack pointer is checked to ensure it resides within the
task's stack page before it is dereferenced in search of the return
address, and the return address register is similarly only output (if
the PC is in a leaf function or the beginning of a non-leaf function).
However unwind_stack() is only meant for unwinding kernel code, so to be
correct the unwind should stop there.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Reviewed-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11700/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Fix a build regression from commit c9017757c532 ("MIPS: init upper 64b
of vector registers when MSA is first used"):
arch/mips/built-in.o: In function `enable_restore_fp_context':
traps.c:(.text+0xbb90): undefined reference to `_init_msa_upper'
traps.c:(.text+0xbb90): relocation truncated to fit: R_MIPS_26 against `_init_msa_upper'
traps.c:(.text+0xbef0): undefined reference to `_init_msa_upper'
traps.c:(.text+0xbef0): relocation truncated to fit: R_MIPS_26 against `_init_msa_upper'
to !CONFIG_CPU_HAS_MSA configurations with older GCC versions, which are
unable to figure out that calls to `_init_msa_upper' are indeed dead.
Of the many ways to tackle this failure choose the approach we have
already taken in `thread_msa_context_live'.
[ralf@linux-mips.org: Drop patch segment to junk file.]
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13271/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
When emulating a jalr instruction with rd == $0, the code in
isBranchInstr was incorrectly writing to GPR $0 which should actually
always remain zeroed. This would lead to any further instructions
emulated which use $0 operating on a bogus value until the task is next
context switched, at which point the value of $0 in the task context
would be restored to the correct zero by a store in SAVE_SOME. Fix this
by not writing to rd if it is $0.
Fixes: 102cedc32a6e ("MIPS: microMIPS: Floating point support.") Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: Maciej W. Rozycki <macro@imgtec.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13160/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Igor Redko [Wed, 8 Jun 2016 16:58:08 +0000 (10:58 -0600)]
virtio_balloon: export 'available' memory to balloon statistics
BugLink: http://bugs.launchpad.net/bugs/1587091
Add a new field, VIRTIO_BALLOON_S_AVAIL, to virtio_balloon memory
statistics protocol, corresponding to 'Available' in /proc/meminfo.
It indicates to the hypervisor how big the balloon can be inflated
without pushing the guest system to swap.
Signed-off-by: Igor Redko <redkoi@virtuozzo.com> Signed-off-by: Denis V. Lunev <den@openvz.org> Reviewed-by: Roman Kagan <rkagan@virtuozzo.com> Cc: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
(cherry picked from commit 5057dcd0f1aaad57e07e728ba20a99e205c6b9de) Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Chris J Arges <chris.j.arges@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Igor Redko [Wed, 8 Jun 2016 16:58:07 +0000 (10:58 -0600)]
mm/page_alloc.c: calculate 'available' memory in a separate function
BugLink: http://bugs.launchpad.net/bugs/1587091
Add a new field, VIRTIO_BALLOON_S_AVAIL, to virtio_balloon memory
statistics protocol, corresponding to 'Available' in /proc/meminfo.
It indicates to the hypervisor how big the balloon can be inflated
without pushing the guest system to swap. This metric would be very
useful in VM orchestration software to improve memory management of
different VMs under overcommit.
This patch (of 2):
Factor out calculation of the available memory counter into a separate
exportable function, in order to be able to use it in other parts of the
kernel.
In particular, it appears a relevant metric to report to the hypervisor
via virtio-balloon statistics interface (in a followup patch).
Signed-off-by: Igor Redko <redkoi@virtuozzo.com> Signed-off-by: Denis V. Lunev <den@openvz.org> Reviewed-by: Roman Kagan <rkagan@virtuozzo.com> Cc: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
(back ported from commit d02bd27bd33dd7e8d22594cd568b81be0cb584cd) Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Conflicts:
fs/proc/meminfo.c
Acked-by: Chris J Arges <chris.j.arges@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Michael Neuling [Fri, 22 Apr 2016 04:57:49 +0000 (14:57 +1000)]
cxl: Poll for outstanding IRQs when detaching a context
BugLink: http://bugs.launchpad.net/bugs/1588468
When detaching contexts, we may still have interrupts in the system
which are yet to be delivered to any CPU and be acked in the PSL.
This can result in a subsequent unrelated process getting an spurious
IRQ or an interrupt for a non-existent context.
This polls the PSL to ensure that the PSL is clear of IRQs for the
detached context, before removing the context from the idr.
Signed-off-by: Michael Neuling <mikey@neuling.org> Tested-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com> Acked-by: Ian Munsie <imunsie@au1.ibm.com> Tested-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
(cherry picked from commit 2bc79ffcbb817873cc43d63118008ab75181b73d) Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Vaibhav Jain [Mon, 29 Feb 2016 05:40:53 +0000 (11:10 +0530)]
cxl: Ignore probes for virtual afu pci devices
BugLink: http://bugs.launchpad.net/bugs/1588468
Add a check at the beginning of cxl_probe function to ignore virtual pci
devices created for each afu registered. This fixes the the errors
messages logged about missing CXL vsec, when cxl probe is unable to
find necessary vsec entries in device pci config space. The error
message logged are of the form :
Frederic Barrat [Fri, 4 Mar 2016 11:26:44 +0000 (12:26 +0100)]
cxl: Remove cxl_get_phys_dev() kernel API
BugLink: http://bugs.launchpad.net/bugs/1588468
The cxl_get_phys_dev() API returns a struct device pointer which could
belong to either a struct pci_dev (bare-metal) or platform_device
(powerVM). To avoid potential problems in drivers, remove that API. It
was introduced to allow drivers to read the VPD of the adapter, but
the cxl driver now provides the cxl_pci_read_adapter_vpd() API for
that purpose.
Co-authored-by: Christophe Lombard <clombard@linux.vnet.ibm.com> Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com> Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com> Acked-by: Ian Munsie <imunsie@au1.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
(cherry picked from commit 0d3a13fbf1d1f3323d04499a727c17c80d156168) Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Frederic Barrat [Fri, 4 Mar 2016 11:26:43 +0000 (12:26 +0100)]
cxlflash: Use new cxl_pci_read_adapter_vpd() API
BugLink: http://bugs.launchpad.net/bugs/1588468
To read the adapter VPD, drivers can't rely on pci config APIs, as it
wouldn't work on powerVM. cxl introduced a new kernel API especially
for this, so start using it.
Co-authored-by: Christophe Lombard <clombard@linux.vnet.ibm.com> Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com> Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com> Reviewed-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com> Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com> Acked-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
(cherry picked from commit ca946d4e4a390a5121bfc9076d85be0ddd55c266) Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
BugLink: http://bugs.launchpad.net/bugs/1588468
Check the AFU state whenever an API is called. The hypervisor may
issue a reset of the adapter when it detects a fault. When it happens,
it launches an error recovery which will either move the AFU to a
permanent failure state, or in the disabled state.
If the AFU is found to be disabled, detach all existing contexts from
it before issuing a AFU reset to re-enable it.
Before detaching contexts, notify any kernel driver through the EEH
callbacks of the AFU pci device.
Co-authored-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com> Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com> Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com> Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com> Acked-by: Ian Munsie <imunsie@au1.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
(cherry picked from commit 0d400f77c19e8d2606f8194846bcf18ebdc9df2a) Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Frederic Barrat [Fri, 4 Mar 2016 11:26:40 +0000 (12:26 +0100)]
cxl: Support the cxl kernel API from a guest
BugLink: http://bugs.launchpad.net/bugs/1588468
Like on bare-metal, the cxl driver creates a virtual PHB and a pci
device for the AFU. The configuration space of the device is mapped to
the configuration record of the AFU.
Reuse the code defined in afu_cr_read8|16|32() when reading the
configuration space of the AFU device.
Even though the (virtual) AFU device is a pci device, the adapter is
not. So a driver using the cxl kernel API cannot read the VPD of the
adapter through the usual PCI interface. Therefore, we add a call to
the cxl kernel API:
ssize_t cxl_read_adapter_vpd(struct pci_dev *dev, void *buf, size_t count);
Co-authored-by: Christophe Lombard <clombard@linux.vnet.ibm.com> Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com> Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com> Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com> Acked-by: Ian Munsie <imunsie@au1.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
(cherry picked from commit d601ea918b878582e60b773f2f943d8d292b2abf) Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
cxl: Support to flash a new image on the adapter from a guest
BugLink: http://bugs.launchpad.net/bugs/1588468
The new flash.c file contains the logic to flash a new image on the
adapter, through a hcall. It is an iterative process, with chunks of
data of 1M at a time. There are also 2 phases: write and verify. The
flash operation itself is driven from a user-land tool.
Once flashing is successful, an rtas call is made to update the device
tree with the new properties values for the adapter and the AFU(s)
Add a new char device for the adapter, so that the flash tool can
access the card, even if there is no valid AFU on it.
Co-authored-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com> Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com> Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com> Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com> Acked-by: Ian Munsie <imunsie@au1.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
(cherry picked from commit 594ff7d067ca42676e27e2a7b5dcc0ff039d08ca) Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
guest.c implements the guest-specific callbacks for the backend API.
The process element ID is not known until the context is attached, so
we have to separate the context ID assigned by the cxl driver from the
process element ID visible to the user applications. In bare-metal,
the 2 IDs match.
Co-authored-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com> Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com> Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com> Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com> Acked-by: Ian Munsie <imunsie@au1.ibm.com>
[mpe: Fix SMP=n build, fix PSERIES=n build, minor whitespace fixes] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
(cherry picked from commit 14baf4d9c739e6e69150512d2eb23c71fffcc192) Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Uma Krishnan [Fri, 4 Mar 2016 21:55:18 +0000 (15:55 -0600)]
cxlflash: Reorder user context initialization
BugLink: http://bugs.launchpad.net/bugs/1588468
In order to support cxlflash in the PowerVM environment, underlying
hypervisor APIs have imposed a kernel API ordering change.
For the superpipe access to LUN, user applications need a context.
The cxlflash module creates this context by making a sequence of
cxl calls. In the current code, a context is initialized via
cxl_dev_context_init() followed by cxl_process_element(), a function
that obtains the process element id. Finally, cxl_start_work()
is called to attach the process element.
In the PowerVM environment, a process element id cannot be obtained
from the hypervisor until the process element is attached. The
cxlflash module is unable to create contexts without a valid
process element id.
To fix this problem, cxl_start_work() is called before obtaining
the process element id.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com> Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 5d1952acd0d56f6b6835aa45bea763ee97b9e66f) Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Matthew R. Ochs [Fri, 4 Mar 2016 21:55:17 +0000 (15:55 -0600)]
cxlflash: Simplify attach path error cleanup
BugLink: http://bugs.launchpad.net/bugs/1588468
The cxlflash_disk_attach() routine currently uses a cascading error
gate strategy for its error cleanup path. While this strategy is
commonly used to handle cleanup scenarios, it is too restrictive when
function callouts need to be restructured. Problems range from
inserting error path bugs in previously 'good' code to the cleanup
path imposing design changes to how the normal path is structured.
A less restrictive approach is needed to support ordering changes
that come about when operating in different environments.
To overcome this restriction, the error cleanup path is modified to
have a single entrypoint and use conditional logic to cleanup where
necessary. Entities that require multiple cleanup steps must be
carefully vetted to ensure their APIs support state. In cases where
they do not (none as of this commit) additional local variables can
be used to maintain state on their behalf.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com> Reviewed-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 8a96b52af58721caf4f7496d0737e8ec6b63c86e) Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Matthew R. Ochs [Fri, 4 Mar 2016 21:55:16 +0000 (15:55 -0600)]
cxlflash: Split out context initialization
BugLink: http://bugs.launchpad.net/bugs/1588468
Presently, context information structures are allocated and
initialized in the same routine, create_context(). This imposes
an ordering restriction such that all pieces of information needed
to initialize a context must be known before the context is even
allocated.
This design point is not flexible when the order of context
creation needs to be modified. Specifically, this can lead to
problems when members of the context information structure are
a part of an ordering dependency (i.e. - the 'work' structure
embedded within the context).
To remedy, the allocation is left as-is, inside of the existing
create_context() routine and the initialization is transitioned
to a new void routine, init_context(). At the same time, in
anticipation of these routines not being called in sequence, a
state boolean is added to the context information structure to
track when the context has been initilized. The context teardown
routine, destroy_context(), is modified to support being called
with a non-initialized context.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com> Reviewed-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 5e6632d19ea2fafaec1b7c4cda7f7157ee8ad983) Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Uma Krishnan [Fri, 4 Mar 2016 21:55:15 +0000 (15:55 -0600)]
cxlflash: Unmap problem state area before detaching master context
BugLink: http://bugs.launchpad.net/bugs/1588468
When operating in the PowerVM environment, the cxlflash module can
receive an error from the hypervisor indicating that there are
existing mappings in the page table for the process MMIO space.
This issue exists because term_afu() currently invokes term_mc()
before stop_afu(), allowing for the master context to be detached
first and the problem state area to be unmapped second.
To resolve this issue, stop_afu() should be called before term_mc().
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com> Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 6ded8b3cbd9a6254da5a38f35e20aa3c316d9092) Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Manoj N. Kumar [Fri, 4 Mar 2016 21:55:14 +0000 (15:55 -0600)]
cxlflash: Simplify PCI registration
BugLink: http://bugs.launchpad.net/bugs/1588468
The calls to pci_request_regions(), pci_resource_start(),
pci_set_dma_mask(), pci_set_master() and pci_save_state() are all
unnecessary for the IBM CXL flash adapter since data buffers
are not required to be mapped to the device's memory.
The use of services such as pci_set_dma_mask() are problematic on
hypervisor managed systems as the IBM CXL flash adapter is operating
under a virtual PCI Host Bridge (virtual PHB) which does not support
these services.
cxlflash 0001:00:00.0: init_pci: Failed to set PCI DMA mask rc=-5
The resolution is to simplify init_pci(), to a point where it does the
bare minimum (pci_enable_device). Similarly, remove the call the
pci_release_regions() from cxlflash_remove().
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com> Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com> Reviewed-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 961487e46a87079a573348896a0d39c1cb10947d) Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
cxl: Separate bare-metal fields in adapter and AFU data structures
BugLink: http://bugs.launchpad.net/bugs/1588468
Introduce sub-structures containing the bare-metal specific fields in
the structures describing the adapter (struct cxl) and AFU (struct
cxl_afu).
Update all their references.
Co-authored-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com> Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com> Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com> Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com> Acked-by: Ian Munsie <imunsie@au1.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
(cherry picked from commit cbffa3a5146a90f46806cef3a98b8be5833727e8) Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
BugLink: http://bugs.launchpad.net/bugs/1588468
The hypervisor calls provide an interface with a coherent platform
facility and function. It matches version 0.16 of the 'PAPR changes'
document.
The following hcalls are supported:
H_ATTACH_CA_PROCESS Attach a process element to a coherent platform
function.
H_DETACH_CA_PROCESS Detach a process element from a coherent
platform function.
H_CONTROL_CA_FUNCTION Allow the partition to manipulate or query
certain coherent platform function behaviors.
H_COLLECT_CA_INT_INFO Collect interrupt info about a coherent.
platform function after an interrupt occurred
H_CONTROL_CA_FAULTS Control the operation of a coherent platform
function after a fault occurs.
H_DOWNLOAD_CA_FACILITY Support for downloading a base adapter image to
the coherent platform facility, and for
validating the entire image after the download.
H_CONTROL_CA_FACILITY Allow the partition to manipulate or query
certain coherent platform facility behaviors.
Co-authored-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com> Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com> Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com> Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com> Acked-by: Ian Munsie <imunsie@au1.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
(cherry picked from commit 444c4ba4616503baf68cffbf6748047d308b8cd2) Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Frederic Barrat [Fri, 4 Mar 2016 11:26:32 +0000 (12:26 +0100)]
cxl: IRQ allocation for guests
BugLink: http://bugs.launchpad.net/bugs/1588468
The PSL interrupt cannot be multiplexed in a guest, as it is not
supported by the hypervisor. So an interrupt will be allocated
for it for each context. It will still be the first interrupt found in
the first interrupt range, but is treated almost like any other AFU
interrupt when creating/deleting the context. Only the handler is
different. Rework the code so that the range 0 is treated like the
other ranges.
Co-authored-by: Christophe Lombard <clombard@linux.vnet.ibm.com> Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com> Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com> Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com> Acked-by: Ian Munsie <imunsie@au1.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
(cherry picked from commit 73d55c3b59f7d9cadc1dbc07d75ccee6c81fdf5b) Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Frederic Barrat [Fri, 4 Mar 2016 11:26:30 +0000 (12:26 +0100)]
cxl: Isolate a few bare-metal-specific calls
BugLink: http://bugs.launchpad.net/bugs/1588468
A few functions are mostly common between bare-metal and guest and
just need minor tuning. To avoid crowding the backend API, introduce a
few 'if' based on the CPU being in HV mode.
Co-authored-by: Christophe Lombard <clombard@linux.vnet.ibm.com> Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com> Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com> Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com> Acked-by: Ian Munsie <imunsie@au1.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
(cherry picked from commit ea2d1f95efd7c100617235918bac370414aec1ad) Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Frederic Barrat [Fri, 4 Mar 2016 11:26:29 +0000 (12:26 +0100)]
cxl: Rename some bare-metal specific functions
BugLink: http://bugs.launchpad.net/bugs/1588468
Rename a few functions, changing the 'cxl_' prefix to either
'cxl_pci_' or 'cxl_native_', to make clear that the implementation is
bare-metal specific.
Those functions will have an equivalent implementation for a guest in
a later patch.
Co-authored-by: Christophe Lombard <clombard@linux.vnet.ibm.com> Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com> Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com> Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com> Acked-by: Ian Munsie <imunsie@au1.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
(cherry picked from commit 2b04cf310ba8c123e9957cfab80274e7606bf53c) Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Frederic Barrat [Fri, 4 Mar 2016 11:26:28 +0000 (12:26 +0100)]
cxl: Introduce implementation-specific API
BugLink: http://bugs.launchpad.net/bugs/1588468
The backend API (in cxl.h) lists some low-level functions whose
implementation is different on bare-metal and in a guest. Each
environment implements its own functions, and the common code uses
them through function pointers, defined in cxl_backend_ops
Co-authored-by: Christophe Lombard <clombard@linux.vnet.ibm.com> Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com> Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com> Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com> Acked-by: Ian Munsie <imunsie@au1.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
(cherry picked from commit 5be587b1110132b4f05e0bc3515a145365e910fe) Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Frederic Barrat [Fri, 4 Mar 2016 11:26:27 +0000 (12:26 +0100)]
cxl: Define process problem state area at attach time only
BugLink: http://bugs.launchpad.net/bugs/1588468
CXL kernel API was defining the process problem state area during
context initialization, making it possible to map the problem state
area before attaching the context. This won't work on a powerVM
guest. So force the logical behavior, like in userspace: attach first,
then map the problem state area.
Remove calls to cxl_assign_psn_space during init. The function is
already called on the attach paths.
Co-authored-by: Christophe Lombard <clombard@linux.vnet.ibm.com> Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com> Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com> Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com> Acked-by: Ian Munsie <imunsie@au1.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
(cherry picked from commit cca44c0192b03d179786ec34b070e7de42966cc6) Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Frederic Barrat [Fri, 4 Mar 2016 11:26:26 +0000 (12:26 +0100)]
cxl: Move bare-metal specific code to specialized files
BugLink: http://bugs.launchpad.net/bugs/1588468
Move a few functions around to better separate code specific to
bare-metal environment from code which will be commonly used between
guest and bare-metal.
Code specific to bare-metal is meant to be in native.c or pci.c
only. It's basically anything which touches the card p1 registers,
some p2 registers not needed from a guest and the PCI interface.
Co-authored-by: Christophe Lombard <clombard@linux.vnet.ibm.com> Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com> Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com> Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com> Acked-by: Ian Munsie <imunsie@au1.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
(cherry picked from commit d56d301b51746e71f7bdaaba10973f054c3c736e) Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
cxl: Move common code away from bare-metal-specific files
BugLink: http://bugs.launchpad.net/bugs/1588468
Move around some functions which will be accessed from the bare-metal
and guest environments.
Code in native.c and pci.c is meant to be bare-metal specific.
Other files contain code which may be shared with guests.
Co-authored-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com> Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com> Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com> Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com> Acked-by: Ian Munsie <imunsie@au1.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
(cherry picked from commit 8633186209e35dfafc27c3d0f0d5e702ab47265f) Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
block: fix blk_rq_get_max_sectors for driver private requests
BugLink: http://bugs.launchpad.net/bugs/1588449
Driver private request types should not get the artifical cap for the
FS requests. This is important to use the full device capabilities
for internal command or NVMe pass through commands.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reported-by: Jeff Lien <Jeff.Lien@hgst.com> Tested-by: Jeff Lien <Jeff.Lien@hgst.com> Reviewed-by: Keith Busch <keith.busch@intel.com>
Updated by me to use an explicit check for the one command type that
does support extended checking, instead of relying on the ordering
of the enum command values - as suggested by Keith.
Signed-off-by: Jens Axboe <axboe@fb.com>
(cherry picked from commit f21018427cb007a0894c36ad702990ab639cbbb4) Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
BugLink: http://bugs.launchpad.net/bugs/1588449
The block layer uses an unsigned short for max_segments. The way we
calculate the value for NVMe tends to generate very large 32-bit values,
which after integer truncation may lead to a zero value instead of
the desired outcome.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reported-by: Jeff Lien <Jeff.Lien@hgst.com> Tested-by: Jeff Lien <Jeff.Lien@hgst.com> Reviewed-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Jens Axboe <axboe@fb.com>
(cherry picked from commit 45686b6198bd824f083ff5293f191d78db9d708a) Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
BugLink: http://bugs.launchpad.net/bugs/1588449
Factor out a helper to set all the device specific queue limits and apply
them to the admin queue in addition to the I/O queues. Without this the
command size on the admin queue is arbitrarily low, and the missing
other limitations are just minefields waiting for victims.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reported-by: Jeff Lien <Jeff.Lien@hgst.com> Tested-by: Jeff Lien <Jeff.Lien@hgst.com> Reviewed-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Jens Axboe <axboe@fb.com>
(cherry picked from commit da35825d9a091a7a1d5824c8468168e2658333ff) Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
irqchip/gicv3-its: numa: Enable workaround for Cavium thunderx erratum 23144
BugLink: http://bugs.launchpad.net/bugs/1589704
The erratum fixes the hang of ITS SYNC command by avoiding inter node
io and collections/cpu mapping on thunderx dual-socket platform.
This fix is only applicable for Cavium's ThunderX dual-socket platform.
Reviewed-by: Robert Richter <rrichter@cavium.com> Signed-off-by: Ganapatrao Kulkarni <gkulkarni@caviumnetworks.com> Signed-off-by: Robert Richter <rrichter@cavium.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
(back-ported from commit fbf8f40e1658cb2f17452dbd3c708e329c5d27e0) Signed-off-by: dann frazier <dann.frazier@canonical.com>
[ dannf: Adjusted for offset changes; dropped Documentation/ updates for
file that didn't exist in v4.4 ] Acked-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
dann frazier [Mon, 6 Jun 2016 21:56:50 +0000 (15:56 -0600)]
UBUNTU: [Config] CONFIG_CAVIUM_ERRATUM_23144=y
Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
BugLink: http://bugs.launchpad.net/bugs/1588945 Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
gcc-6 started warning by default about variables that are not
used anywhere and that are marked 'const', generating many
false positives in an allmodconfig build, e.g.:
arch/arm/mach-davinci/board-da830-evm.c:282:20: warning: 'da830_evm_emif25_pins' defined but not used [-Wunused-const-variable=]
arch/arm/plat-omap/dmtimer.c:958:34: warning: 'omap_timer_match' defined but not used [-Wunused-const-variable=]
drivers/bluetooth/hci_bcm.c:625:39: warning: 'acpi_bcm_default_gpios' defined but not used [-Wunused-const-variable=]
drivers/char/hw_random/omap-rng.c:92:18: warning: 'reg_map_omap4' defined but not used [-Wunused-const-variable=]
drivers/devfreq/exynos/exynos5_bus.c:381:32: warning: 'exynos5_busfreq_int_pm' defined but not used [-Wunused-const-variable=]
drivers/dma/mv_xor.c:1139:34: warning: 'mv_xor_dt_ids' defined but not used [-Wunused-const-variable=]
This is similar to the existing -Wunused-but-set-variable warning
that was added in an earlier release and that we disable by default
now and only enable when W=1 is set, so it makes sense to do
the same here. Once we have eliminated the majority of the
warnings for both, we can put them back into the default list.
We probably want this in backport kernels as well, to allow building
them with gcc-6 without introducing extra warnings.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Olof Johansson <olof@lixom.net> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Michal Marek <mmarek@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Now that we've done a more comprehensive fix with the intermediate
target state we can remove the previous hack introduced with commit 90a88d6ef88e ("scsi: fix soft lockup in scsi_remove_target() on module
removal").
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Add intermediate STARGET_REMOVE state to scsi_target_state to avoid
running into the BUG_ON() in scsi_target_reap(). The STARGET_REMOVE
state is only valid in the path from scsi_remove_target() to
scsi_target_destroy() indicating this target is going to be removed.
This re-fixes the problem introduced in commits bc3f02a795d3 ("[SCSI]
scsi_remove_target: fix softlockup regression on hot remove") and 40998193560d ("scsi: restart list search after unlock in
scsi_remove_target") in a more comprehensive way.
[mkp: Included James' fix for scsi_target_destroy()]
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de> Fixes: 40998193560dab6c3ce8d25f4fa58a23e252ef38 Reported-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Tested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: James Bottomley <jejb@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
The HPFS filesystem used generic_show_options to produce string that is
displayed in /proc/mounts. However, there is a problem that the options
may disappear after remount. If we mount the filesystem with option1
and then remount it with option2, /proc/mounts should show both option1
and option2, however it only shows option2 because the whole option
string is replaced with replace_mount_options in hpfs_remount_fs.
To fix this bug, implement the hpfs_show_options function that prints
options that are currently selected.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Commit ce657611baf9 ("hpfs: kstrdup() out of memory handling") checks if
the kstrdup function returns NULL due to out-of-memory condition.
However, if we are remounting a filesystem with no change to
filesystem-specific options, the parameter data is NULL. In this case,
kstrdup returns NULL (because it was passed NULL parameter), although no
out of memory condition exists. The mount syscall then fails with
ENOMEM.
This patch fixes the bug. We fail with ENOMEM only if data is non-NULL.
The patch also changes the call to replace_mount_options - if we didn't
pass any filesystem-specific options, we don't call
replace_mount_options (thus we don't erase existing reported options).
Fixes: ce657611baf9 ("hpfs: kstrdup() out of memory handling") Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Ezequiel reported that he's facing UBI going into read-only
mode after power cut. It turned out that this behavior happens
only when updating a static volume is interrupted and Fastmap is
used.
UBI checks static volumes for data consistency and reads the
whole volume upon first open. If the volume is found erroneous
users of UBI cannot read from it, but another volume update is
possible to fix it. The check is performed by running
ubi_eba_read_leb() on every allocated LEB of the volume.
For static volumes ubi_eba_read_leb() computes the checksum of all
data stored in a LEB. To verify the computed checksum it has to read
the LEB's volume header which stores the original checksum.
If the volume header is not found UBI treats this as fatal internal
error and switches to RO mode. If the UBI device was attached via a
full scan the assumption is correct, the volume header has to be
present as it had to be there while scanning to get known as mapped.
If the attach operation happened via Fastmap the assumption is no
longer correct. When attaching via Fastmap UBI learns the mapping
table from Fastmap's snapshot of the system state and not via a full
scan. It can happen that a LEB got unmapped after a Fastmap was
written to the flash. Then UBI can learn the LEB still as mapped and
accessing it returns only 0xFF bytes. As UBI is not a FTL it is
allowed to have mappings to empty PEBs, it assumes that the layer
above takes care of LEB accounting and referencing.
UBIFS does so using the LEB property tree (LPT).
For static volumes UBI blindly assumes that all LEBs are present and
therefore special actions have to be taken.
The described situation can happen when updating a static volume is
interrupted, either by a user or a power cut.
The volume update code first unmaps all LEBs of a volume and then
writes LEB by LEB. If the sequence of operations is interrupted UBI
detects this either by the absence of LEBs, no volume header present
at scan time, or corrupted payload, detected via checksum.
In the Fastmap case the former method won't trigger as no scan
happened and UBI automatically thinks all LEBs are present.
Only by reading data from a LEB it detects that the volume header is
missing and incorrectly treats this as fatal error.
To deal with the situation ubi_eba_read_leb() from now on checks
whether we attached via Fastmap and handles the absence of a
volume header like a data corruption error.
This way interrupted static volume updates will correctly get detected
also when Fastmap is used.
Reported-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar> Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
The generic copy_siginfo() is currently defined in
asm-generic/siginfo.h, after including uapi/asm-generic/siginfo.h which
defines the generic struct siginfo. However this makes it awkward for an
architecture to use it if it has to define its own struct siginfo (e.g.
MIPS and potentially IA64), since it means that asm-generic/siginfo.h
can only be included after defining the arch-specific siginfo, which may
be problematic if the arch-specific definition needs definitions from
uapi/asm-generic/siginfo.h.
It is possible to work around this by first including
uapi/asm-generic/siginfo.h to get the constants before defining the
arch-specific siginfo, and include asm-generic/siginfo.h after. However
uapi headers can't be included by other uapi headers, so that first
include has to be in an ifdef __kernel__, with the non __kernel__ case
including the non-UAPI header instead.
Instead of that mess, move the generic copy_siginfo() definition into
linux/signal.h, which allows an arch-specific uapi/asm/siginfo.h to
include asm-generic/siginfo.h and define the arch-specific siginfo, and
for the generic copy_siginfo() to see that arch-specific definition.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Petr Malat <oss@malat.biz> Cc: Tony Luck <tony.luck@intel.com> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: Christopher Ferris <cferris@google.com> Cc: linux-arch@vger.kernel.org Cc: linux-mips@linux-mips.org Cc: linux-ia64@vger.kernel.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12478/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
The headphone has noise when playing sound or switching microphone sources.
It uses the same codec on XPS 13 9350, but with different subsystem ID.
Applying the fixup can solve the issue.
Also, changing the model name to better differentiate models.
v2: Reorder by device ID.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
The bar number is found in reg2 within the gdd. Therefore
we need to change the assigment from reg1 to reg2 which
is the correct location.
Signed-off-by: Andreas Werner <andreas.werner@men.de> Fixes: '3764e82e5' drivers: Introduce MEN Chameleon Bus Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Add missing locking to:
* bcm2835_pll_divider_on
* bcm2835_pll_divider_off
to protect the read modify write cycle for the
register access protecting both cm_reg and a2w_reg
registers.
Fixes: 41691b8862e2 ("clk: bcm2835: Add support for programming the
audio domain clocks")
Signed-off-by: Martin Sperl <kernel@martin.sperl.org> Signed-off-by: Eric Anholt <eric@anholt.net> Reviewed-by: Eric Anholt <eric@anholt.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
51d7d5205d33 ("powerpc: Add smp_mb() to arch_spin_is_locked()") d86b8da04dfa ("arm64: spinlock: serialise spin_unlock_wait against concurrent lockers")
qspinlock suffers from the fact that the _Q_LOCKED_VAL store is
unordered inside the ACQUIRE of the lock.
And while this is not a problem for the regular mutual exclusive
critical section usage of spinlocks, it breaks creative locking like:
spin_lock(A) spin_lock(B)
spin_unlock_wait(B) if (!spin_is_locked(A))
do_something() do_something()
In that both CPUs can end up running do_something at the same time,
because our _Q_LOCKED_VAL store can drop past the spin_unlock_wait()
spin_is_locked() loads (even on x86!!).
To avoid making the normal case slower, add smp_mb()s to the less used
spin_unlock_wait() / spin_is_locked() side of things to avoid this
problem.
Reported-and-tested-by: Davidlohr Bueso <dave@stgolabs.net> Reported-by: Giovanni Gherdovich <ggherdovich@suse.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
This patch fixes the broken serial log when changing the clock source
of uart device. Before disabling the original clock source, this patch
enables the new clock source to protect the clock off state for a split second.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
There is a special register that shows interrupt status by source. In
particular case the source can be a combination of DMA Tx, DMA Rx, and UART.
Read the register and call the handlers only for sources that request an
interrupt.
Fixes: 6ede6dcd87aa ("serial: 8250_mid: add support for DMA engine handling from UART MMIO") Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Unlike Intel Medfield and Tangier platforms DNV uses PCI BAR0 for IO compatible
resources and BAR1 for MMIO. We need latter in a way to support DMA. Introduce
an additional field in the internal structure and pass PCI BAR based on device
ID.
Reported-by: "Lai, Poey Seng" <poey.seng.lai@intel.com> Fixes: 6ede6dcd87aa ("serial: 8250_mid: add support for DMA engine handling from UART MMIO") Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Since commit 21947ba654a6 ("serial: 8250_pci: replace switch-case by
formula"), the 8250 driver crashes in the byt_set_termios() function
with a divide error. This is caused by the fact that a baud rate of 0 (B0)
is not handled properly. Fix it by falling back to B9600 in this case.
Signed-off-by: David Müller <d.mueller@elsoft.ch> Fixes: 21947ba654a6 ("serial: 8250_pci: replace switch-case by formula") Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
OpenSSH expects the (non-blocking) read() of pty master to return
EAGAIN only if it has received all of the slave-side output after
it has received SIGCHLD. This used to work on pre-3.12 kernels.
This fix effectively forces non-blocking read() and poll() to
block for parallel i/o to complete for all ttys. It also unwinds
these changes:
Inspired by analysis and patch from Marc Aurele La France <tsi@tuyoix.net>
Reported-by: Volth <openssh@volth.com> Reported-by: Marc Aurele La France <tsi@tuyoix.net> BugLink: https://bugzilla.mindrot.org/show_bug.cgi?id=52 BugLink: https://bugzilla.mindrot.org/show_bug.cgi?id=2492 Signed-off-by: Brian Bloniarz <brian.bloniarz@gmail.com> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Commit 1cf6e8fc8341 ("tty/serial: at91: fix RTS line management when
hardware handshake is enabled") actually allowed to enable hardware
handshaking.
Before, the CRTSCTS flags was silently ignored.
As the DMA controller can't drive RTS (as explain in the commit message).
Ensure that hardware flow control stays disabled when DMA is used and FIFOs
are not available.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Fixes: 1cf6e8fc8341 ("tty/serial: at91: fix RTS line management when hardware handshake is enabled") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
When csw->con_startup() fails in do_register_con_driver, we return no
error (i.e. 0). This was changed back in 2006 by commit 3e795de763.
Before that we used to return -ENODEV.
So fix the return value to be -ENODEV in that case again.
Fixes: 3e795de763 ("VT binding: Add binding/unbinding support for the VT console") Signed-off-by: Jiri Slaby <jslaby@suse.cz> Reported-by: "Dan Carpenter" <dan.carpenter@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
b4ff8389ed14 is incomplete: relies on nr_legacy_irqs() to get the number
of legacy interrupts when actually nr_legacy_irqs() returns 0 after
probe_8259A(). Use NR_IRQS_LEGACY instead.
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
This ensures that the guest doesn't see XSAVE extensions
(e.g. xgetbv1 or xsavec) that the host lacks.
Cc: stable@vger.kernel.org Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
[4.5 does have CPUID_D_1_EAX, but earlier kernels don't, so use
the numeric value. This is consistent with other occurrences
of cpuid_mask in arch/x86/kvm/cpuid.c - Paolo] Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Writing CP0_Compare clears the timer interrupt pending bit
(CP0_Cause.TI), but this wasn't being done atomically. If a timer
interrupt raced with the write of the guest CP0_Compare, the timer
interrupt could end up being pending even though the new CP0_Compare is
nowhere near CP0_Count.
We were already updating the hrtimer expiry with
kvm_mips_update_hrtimer(), which used both kvm_mips_freeze_hrtimer() and
kvm_mips_resume_hrtimer(). Close the race window by expanding out
kvm_mips_update_hrtimer(), and clearing CP0_Cause.TI and setting
CP0_Compare between the freeze and resume. Since the pending timer
interrupt should not be cleared when CP0_Compare is written via the KVM
user API, an ack argument is added to distinguish the source of the
write.
Fixes: e30492bbe95a ("MIPS: KVM: Rewrite count/compare timer emulation") Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: "Radim KrÄ\8dmář" <rkrcmar@redhat.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org Cc: kvm@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
There's a particularly narrow and subtle race condition when the
software emulated guest timer is frozen which can allow a guest timer
interrupt to be missed.
This happens due to the hrtimer expiry being inexact, so very
occasionally the freeze time will be after the moment when the emulated
CP0_Count transitions to the same value as CP0_Compare (so an IRQ should
be generated), but before the moment when the hrtimer is due to expire
(so no IRQ is generated). The IRQ won't be generated when the timer is
resumed either, since the resume CP0_Count will already match CP0_Compare.
With VZ guests in particular this is far more likely to happen, since
the soft timer may be frozen frequently in order to restore the timer
state to the hardware guest timer. This happens after 5-10 hours of
guest soak testing, resulting in an overflow in guest kernel timekeeping
calculations, hanging the guest. A more focussed test case to
intentionally hit the race (with the help of a new hypcall to cause the
timer state to migrated between hardware & software) hits the condition
fairly reliably within around 30 seconds.
Instead of relying purely on the inexact hrtimer expiry to determine
whether an IRQ should be generated, read the guest CP0_Compare and
directly check whether the freeze time is before or after it. Only if
CP0_Count is on or after CP0_Compare do we check the hrtimer expiry to
determine whether the last IRQ has already been generated (which will
have pushed back the expiry by one timer period).
Fixes: e30492bbe95a ("MIPS: KVM: Rewrite count/compare timer emulation") Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: "Radim KrÄ\8dmář" <rkrcmar@redhat.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org Cc: kvm@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Commit d28bc9dd25ce reversed the order of two lines which initialize cr0,
allowing the current (old) cr0 value to mess up vcpu initialization.
This was observed in the checks for cr0 X86_CR0_WP bit in the context of
kvm_mmu_reset_context(). Besides, setting vcpu->arch.cr0 after vmx_set_cr0()
is completely redundant. Change the order back to ensure proper vcpu
initialization.
The combination of booting with ovmf firmware when guest vcpus > 1 and kvm's
ept=N option being set results in a VM-entry failure. This patch fixes that.
Fixes: d28bc9dd25ce ("KVM: x86: INIT and reset sequences are different") Signed-off-by: Bruce Rogers <brogers@suse.com> Signed-off-by: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
DMA is optional with this driver. If it was not enabled the devpriv->dma
pointer will be NULL.
Fix the possible NULL pointer dereference when trying to disable the DMA
channels in das1800_ai_cancel() and tidy up the comments to fix the
checkpatch.pl issues:
WARNING: line over 80 characters
It's probably harmless in das1800_ai_setup_dma() because the 'desc' pointer
will not be used if DMA is disabled but fix it there also.
Fixes: 99dfc3357e98 ("staging: comedi: das1800: remove depends on ISA_DMA_API limitation") Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Reviewed-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
The current implemenentation restart the sent pattern for each entry in
the sg list. The receiving end expects a continuous pattern, and test
will fail unless scatterilst entries happen to be aligned with the
pattern
Fix this by calculating the pattern byte based on total sent size
instead of just the current sg entry.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Fixes: 8b5249019352 ("[PATCH] USB: usbtest: scatterlist OUT data pattern testing") Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
When binding the function to usb_configuration, check whether the thread
is running before starting another one. Without that, when function
instance is added to multiple configurations, fsg_bing starts multiple
threads with all but the latest one being forgotten by the driver. This
leads to obvious thread leaks, possible lockups when trying to halt the
machine and possible more issues.
This fixes issues with legacy/multi¹ gadget as well as configfs gadgets
when mass_storage function is added to multiple configurations.
This change also simplifies API since the legacy gadgets no longer need
to worry about starting the thread by themselves (which was where bug
in legacy/multi was in the first place).
N.B., this patch doesn’t address adding single mass_storage function
instance to a single configuration twice. Thankfully, there’s no
legitimate reason for such setup plus, if I’m not mistaken, configfs
gadget doesn’t even allow it to be expressed.
¹ I have no example failure though. Conclusion that legacy/multi has
a bug is based purely on me reading the code.
Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Michal Nazarewicz <mina86@mina86.com> Tested-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
In the current implementation functionfs generates a EFAULT for async read
operations if the read buffer size is larger than the URB data size. Since
a application does not necessarily know how much data the host side is
going to send it typically supplies a buffer larger than the actual data,
which will then result in a EFAULT error.
This behaviour was introduced while refactoring the code to use iov_iter
interface in commit c993c39b8639 ("gadget/function/f_fs.c: use put iov_iter
into io_data"). The original code took the minimum over the URB size and
the user buffer size and then attempted to copy that many bytes using
copy_to_user(). If copy_to_user() could not copy all data a EFAULT error
was generated. Restore the original behaviour by only generating a EFAULT
error when the number of bytes copied is not the size of the URB and the
target buffer has not been fully filled.
Commit 342f39a6c8d3 ("usb: gadget: f_fs: fix check in read operation")
already fixed the same problem for the synchronous read path.
Fixes: c993c39b8639 ("gadget/function/f_fs.c: use put iov_iter into io_data") Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: lei liu <liu.lei78@zte.com.cn>
[johan: rebase and replace commit message ] Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: lei liu <liu.lei78@zte.com.cn>
[properly sort them - gregkh] Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Added support for Gemalto's Cinterion PH8 and AHxx products
with 2 RmNet Interfaces and products with 1 RmNet + 1 USB Audio interface.
In addition some minor renaming and formatting.
Signed-off-by: Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com>
[johan: sort current entries and trim trailing whitespace ] Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
URBs and buffers allocated in attach for Epic devices would never be
deallocated in case of a later probe error (e.g. failure to allocate
minor numbers) as disconnect is then never called.
Fix by moving deallocation to release and making sure that the
URBs are first unlinked.
Fixes: f9c99bb8b3a1 ("USB: usb-serial: replace shutdown with disconnect,
release") Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Private data, URBs and buffers allocated for Epic devices during
attach were never released on errors (e.g. missing endpoints).
Fixes: 6e8cf7751f9f ("USB: add EPIC support to the io_edgeport driver") Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
The interface read URB is submitted in attach, but was only unlinked by
the driver at disconnect.
In case of a late probe error (e.g. due to failed minor allocation),
disconnect is never called and we would end up with active URBs for an
unbound interface. This in turn could lead to deallocated memory being
dereferenced in the completion callback.
Fixes: f7a33e608d9a ("USB: serial: add quatech2 usb to serial driver") Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
The interface instat and indat URBs were submitted in attach, but never
unlinked in release before deallocating the corresponding transfer
buffers.
In the case of a late probe error (e.g. due to failed minor allocation),
disconnect would not have been called before release, causing the
buffers to be freed while the URBs are still in use. We'd also end up
with active URBs for an unbound interface.
Fixes: f9c99bb8b3a1 ("USB: usb-serial: replace shutdown with disconnect,
release") Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
The interface read and event URBs are submitted in attach, but were
never explicitly unlinked by the driver. Instead the URBs would have
been killed by usb-serial core on disconnect.
In case of a late probe error (e.g. due to failed minor allocation),
disconnect is never called and we could end up with active URBs for an
unbound interface. This in turn could lead to deallocated memory being
dereferenced in the completion callbacks.
Fixes: ee467a1f2066 ("USB: serial: add Moxa UPORT 12XX/14XX/16XX
driver") Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Ensure that mei_cl_read_start is called under the device lock
also in the bus layer. The function updates global ctrl_wr_list
which should be locked.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
When a message is received and amthif client is not in reading state
the message is ignored and left dangling in the queue. This may happen
after one of the amthif host connections is closed w/o completing the
reading. Another client will pick up a wrong message on next read
attempt which will lead to link reset.
To prevent this the driver has to properly discard the message when
amthif client is not in reading state.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
We move the list flushing to the completion routine.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
hci_vhci driver creates a hci device object dynamically upon each
HCI_VENDOR_PKT write. Although it checks the already created object
and returns an error, it's still racy and may build multiple hci_dev
objects concurrently when parallel writes are performed, as the device
tracks only a single hci_dev object.
This patch introduces a mutex to protect against the concurrent device
creations.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
The write handler allocates skbs and queues them into data->readq.
Read side should read them, if there is any. If there is none, skbs
should be dropped by hdev->flush. But this happens only if the device
is HCI_UP, i.e. hdev->power_on work was triggered already. When it was
not, skbs stay allocated in the queue when /dev/vhci is closed. So
purge the queue in ->release.
Program to reproduce:
#include <err.h>
#include <fcntl.h>
#include <stdio.h>
#include <unistd.h>
Both vhci_get_user and vhci_release race with open_timeout work. They
both contain cancel_delayed_work_sync, but do not test whether the
work actually created hdev or not. Since the work can be in progress
and _sync will wait for finishing it, we can have data->hdev allocated
when cancel_delayed_work_sync returns. But the call sites do 'if
(data->hdev)' *before* cancel_delayed_work_sync.
As a result:
* vhci_get_user allocates a second hdev and puts it into
data->hdev. The former is leaked.
* vhci_release does not release data->hdev properly as it thinks there
is none.
Fix both cases by moving the actual test *after* the call to
cancel_delayed_work_sync.
This can be hit by this program:
#include <err.h>
#include <fcntl.h>
#include <stdio.h>
#include <stdlib.h>
#include <time.h>
#include <unistd.h>
#include <sys/stat.h>
#include <sys/types.h>
int main(int argc, char **argv)
{
int fd;
srand(time(NULL));
while (1) {
const int delta = (rand() % 200 - 100) * 100;
fd = open("/dev/vhci", O_RDWR);
if (fd < 0)
err(1, "open");
And the result is:
BUG: KASAN: use-after-free in skb_queue_tail+0x13e/0x150 at addr ffff88006b0c1228
Read of size 8 by task kworker/u13:1/32068
=============================================================================
BUG kmalloc-192 (Tainted: G E ): kasan: bad access detected
-----------------------------------------------------------------------------
Disabling lock debugging due to kernel taint
INFO: Allocated in vhci_open+0x50/0x330 [hci_vhci] age=260 cpu=3 pid=32040
...
kmem_cache_alloc_trace+0x150/0x190
vhci_open+0x50/0x330 [hci_vhci]
misc_open+0x35b/0x4e0
chrdev_open+0x23b/0x510
...
INFO: Freed in vhci_release+0xa4/0xd0 [hci_vhci] age=9 cpu=2 pid=32040
...
__slab_free+0x204/0x310
vhci_release+0xa4/0xd0 [hci_vhci]
...
INFO: Slab 0xffffea0001ac3000 objects=16 used=13 fp=0xffff88006b0c1e00 flags=0x5fffff80004080
INFO: Object 0xffff88006b0c1200 @offset=4608 fp=0xffff88006b0c0600
Bytes b4 ffff88006b0c11f0: 09 df 00 00 01 00 00 00 00 00 00 00 00 00 00 00 ................
Object ffff88006b0c1200: 00 06 0c 6b 00 88 ff ff 00 00 00 00 00 00 00 00 ...k............
Object ffff88006b0c1210: 10 12 0c 6b 00 88 ff ff 10 12 0c 6b 00 88 ff ff ...k.......k....
Object ffff88006b0c1220: c0 46 c2 6b 00 88 ff ff c0 46 c2 6b 00 88 ff ff .F.k.....F.k....
Object ffff88006b0c1230: 01 00 00 00 01 00 00 00 e0 ff ff ff 0f 00 00 00 ................
Object ffff88006b0c1240: 40 12 0c 6b 00 88 ff ff 40 12 0c 6b 00 88 ff ff @..k....@..k....
Object ffff88006b0c1250: 50 0d 6e a0 ff ff ff ff 00 02 00 00 00 00 ad de P.n.............
Object ffff88006b0c1260: 00 00 00 00 00 00 00 00 ab 62 02 00 01 00 00 00 .........b......
Object ffff88006b0c1270: 90 b9 19 81 ff ff ff ff 38 12 0c 6b 00 88 ff ff ........8..k....
Object ffff88006b0c1280: 03 00 20 00 ff ff ff ff ff ff ff ff 00 00 00 00 .. .............
Object ffff88006b0c1290: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
Object ffff88006b0c12a0: 00 00 00 00 00 00 00 00 00 80 cd 3d 00 88 ff ff ...........=....
Object ffff88006b0c12b0: 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 . ..............
Redzone ffff88006b0c12c0: bb bb bb bb bb bb bb bb ........
Padding ffff88006b0c13f8: 00 00 00 00 00 00 00 00 ........
CPU: 3 PID: 32068 Comm: kworker/u13:1 Tainted: G B E 4.4.6-0-default #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.8.1-0-g4adadbd-20151112_172657-sheep25 04/01/2014
Workqueue: hci0 hci_cmd_work [bluetooth] 00000000ffffffffffffffff81926cfaffff88006be37c68ffff88006bc27180 ffff88006b0c1200ffff88006b0c1234ffffffff81577993ffffffff82489320 ffff88006bc242400000000000000046ffff88006a100000000000026e51eb80
Call Trace:
...
[<ffffffff81ec8ebe>] ? skb_queue_tail+0x13e/0x150
[<ffffffffa06e027c>] ? vhci_send_frame+0xac/0x100 [hci_vhci]
[<ffffffffa0c61268>] ? hci_send_frame+0x188/0x320 [bluetooth]
[<ffffffffa0c61515>] ? hci_cmd_work+0x115/0x310 [bluetooth]
[<ffffffff811a1375>] ? process_one_work+0x815/0x1340
[<ffffffff811a1f85>] ? worker_thread+0xe5/0x11f0
[<ffffffff811a1ea0>] ? process_one_work+0x1340/0x1340
[<ffffffff811b3c68>] ? kthread+0x1c8/0x230
...
Memory state around the buggy address: ffff88006b0c1100: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff88006b0c1180: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff88006b0c1200: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff88006b0c1280: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc ffff88006b0c1300: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
008GE0 Toshiba mmc in some Intel Baytrail tablets responds to
MMC_SEND_EXT_CSD in 450-600ms.
This patch will...
() Increase the long read time quirk timeout from 300ms to 600ms. Original
author of that quirk says 300ms was only a guess and that the number
may need to be raised in the future.
() Add this specific MMC to the quirk
Signed-off-by: Matt Gumbel <matthew.k.gumbel@intel.com> Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Some BIOSes unconditionally send an ACPI notification to RBTN when the
system is resuming from suspend. This makes dell-rbtn send an input
event to userspace as if a function key was pressed. Prevent this by
ignoring all the notifications received while the device is suspended.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=106031 Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com> Tested-by: Alex Hung <alex.hung@canonical.com> Reviewed-by: Pali Rohár <pali.rohar@gmail.com> Signed-off-by: Darren Hart <dvhart@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>