The previous code assumed that a higher hardware value always resulted
in a bigger divider, which is correct for the regular clocks, but is
an invalid assumption when a divider table is provided for the clock.
Perfect example of this is the PLL0_HALF clock, which applies a /2
divider with the hardware value 0, and a /1 divider otherwise.
Fixes: a9fa2893fcc6 ("clk: ingenic: Add support for divider tables") Cc: <stable@vger.kernel.org> # 5.2 Signed-off-by: Paul Cercueil <paul@crapouillou.net> Link: https://lore.kernel.org/r/20201212135733.38050-1-paul@crapouillou.net Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
It is found on many allwinner soc that there is a low probability that
the interrupt status cannot be read in sunxi_pinctrl_irq_handler. This
will cause the interrupt status of a gpio bank to always be active on
gic, preventing gic from responding to other spi interrupts correctly.
So we should call the chained_irq_* each time enter sunxi_pinctrl_irq_handler().
md-cluster uses MD_CLUSTER_SEND_LOCK to make node can exclusively send msg.
During sending msg, node can concurrently receive msg from another node.
When node does resync job, grab token_lockres:EX may trigger a deadlock:
```
nodeA nodeB
-------------------- --------------------
a.
send METADATA_UPDATED
held token_lockres:EX
b.
md_do_sync
resync_info_update
send RESYNCING
+ set MD_CLUSTER_SEND_LOCK
+ wait for holding token_lockres:EX
c.
mdadm /dev/md0 --remove /dev/sdg
+ held reconfig_mutex
+ send REMOVE
+ wait_event(MD_CLUSTER_SEND_LOCK)
d.
recv_daemon //METADATA_UPDATED from A
process_metadata_update
+ (mddev_trylock(mddev) ||
MD_CLUSTER_HOLDING_MUTEX_FOR_RECVD)
//this time, both return false forever
```
Explaination:
a. A send METADATA_UPDATED
This will block another node to send msg
b. B does sync jobs, which will send RESYNCING at intervals.
This will be block for holding token_lockres:EX lock.
c. B do "mdadm --remove", which will send REMOVE.
This will be blocked by step <b>: MD_CLUSTER_SEND_LOCK is 1.
d. B recv METADATA_UPDATED msg, which send from A in step <a>.
This will be blocked by step <c>: holding mddev lock, it makes
wait_event can't hold mddev lock. (btw,
MD_CLUSTER_HOLDING_MUTEX_FOR_RECVD keep ZERO in this scenario.)
There is a similar deadlock in commit 0ba959774e93
("md-cluster: use sync way to handle METADATA_UPDATED msg")
In that commit, step c is "update sb". This patch step c is
"mdadm --remove".
For fixing this issue, we can refer the solution of function:
metadata_update_start. Which does the same grab lock_token action.
lock_comm can use the same steps to avoid deadlock. By moving
MD_CLUSTER_HOLDING_MUTEX_FOR_RECVD from lock_token to lock_comm.
It enlarge a little bit window of MD_CLUSTER_HOLDING_MUTEX_FOR_RECVD,
but it is safe & can break deadlock.
Repro steps (I only triggered 3 times with hundreds tests):
two nodes share 3 iSCSI luns: sdg/sdh/sdi. Each lun size is 1GB.
```
ssh root@node2 "mdadm -S --scan"
mdadm -S --scan
for i in {g,h,i};do dd if=/dev/zero of=/dev/sd$i oflag=direct bs=1M \
count=20; done
Reshape request should be blocked with ongoing resync job. In cluster
env, a node can start resync job even if the resync cmd isn't executed
on it, e.g., user executes "mdadm --grow" on node A, sometimes node B
will start resync job. However, current update_raid_disks() only check
local recovery status, which is incomplete. As a result, we see user will
execute "mdadm --grow" successfully on local, while the remote node deny
to do reshape job when it doing resync job. The inconsistent handling
cause array enter unexpected status. If user doesn't observe this issue
and continue executing mdadm cmd, the array doesn't work at last.
Fix this issue by blocking reshape request. When node executes "--grow"
and detects ongoing resync, it should stop and report error to user.
The following script reproduces the issue with ~100% probability.
(two nodes share 3 iSCSI luns: sdg/sdh/sdi. Each lun size is 1GB)
```
# on node1, node2 is the remote node.
ssh root@node2 "mdadm -S --scan"
mdadm -S --scan
for i in {g,h,i};do dd if=/dev/zero of=/dev/sd$i oflag=direct bs=1M \
count=20; done
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp() assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv() data with alignment
explicitly requested. This data is allocated with kzalloc() so no
data can leak apart from previous readings.
In this driver the timestamp can end up in various different locations
depending on what other channels are enabled. As a result, we don't
use a structure to specify it's position as that would be misleading.
Fixes: e717f8c6dfec ("iio: adc: Add the TI ads124s08 ADC code") Reported-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Cc: Dan Murphy <dmurphy@ti.com> Cc: <Stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200920112742.170751-9-jic23@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The buffer is expressed as a u32 array, yet the extra space for
the s64 timestamp was expressed as sizeof(s64)/sizeof(u16).
This will result in 2 extra u32 elements.
Fix by dividing by sizeof(u32).
Fixes: e717f8c6dfec ("iio: adc: Add the TI ads124s08 ADC code") Signed-off-by: Jonathan Cameron<Jonathan.Cameron@huawei.com> Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Cc: Dan Murphy <dmurphy@ti.com> Cc: <Stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200920112742.170751-8-jic23@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The comment implies this device has 3 sensor types, but it only
has an accelerometer and a gyroscope (both 3D). As such the
buffer does not need to be as long as stated.
Note I've separated this from the following patch which fixes
the alignment for passing to iio_push_to_buffers_with_timestamp()
as they are different issues even if they affect the same line
of code.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Cc: Daniel Baluta <daniel.baluta@oss.nxp.com> Cc: <Stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200920112742.170751-5-jic23@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Whilst this is another case of the issue Lars reported with
an array of elements of smaller than 8 bytes being passed
to iio_push_to_buffers_with_timestamp(), the solution here is
a bit different from the other cases and relies on __aligned
working on the stack (true since 4.6?)
This one is unusual. We have to do an explicit memset() each time
as we are reading 3 bytes into a potential 4 byte channel which
may sometimes be a 2 byte channel depending on what is enabled.
As such, moving the buffer to the heap in the iio_priv structure
doesn't save us much. We can't use a nice explicit structure
on the stack either as the data channels have different storage
sizes and are all separately controlled.
Fixes: cc26ad455f57 ("iio: Add Freescale MPL3115A2 pressure / temperature sensor driver") Reported-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Cc: Peter Meerwald <pmeerw@pmeerw.net> Cc: <Stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200920112742.170751-7-jic23@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp() assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv() data.
This data is allocated with kzalloc() so no data can leak apart from
previous readings.
The explicit alignment of ts is not necessary in this case but
does make the code slightly less fragile so I have included it.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp() assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv()
This data is allocated with kzalloc() so no data can leak apart
from previous readings.
A local unsigned int variable is used for the regmap call so it
is clear there is no potential issue with writing into the padding
of the structure.
Fixes: 3025c8688c1e ("iio: light: add support for UVIS25 sensor") Reported-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Acked-by: Lorenzo Bianconi <lorenzo@kernel.org> Cc: <Stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200920112742.170751-3-jic23@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp() assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv().
This data is allocated with kzalloc() so no data can leak apart
from previous readings and in this case the status byte from the device.
The forced alignment of ts is not necessary in this case but it
potentially makes the code less fragile.
>From personal communications with Mikko:
We could probably split the reading of the int register, but it
would mean a significant performance cost of 20 i2c clock cycles.
Fixes: e12ffd241c00 ("iio: light: rpr0521 triggered buffer") Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Cc: Mikko Koivunen <mikko.koivunen@fi.rohmeurope.com> Cc: <Stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200920112742.170751-2-jic23@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Fix the missing clk_disable_unprepare() of info->pclk
before return from rockchip_saradc_resume in the error
handling case when fails to prepare and enable info->clk.
Suggested-by: Robin Murphy <robin.murphy@arm.com> Fixes: 44d6f2ef94f9 ("iio: adc: add driver for Rockchip saradc") Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com> Cc: <Stable@vger.kernel.org> Link: https://lore.kernel.org/r/20201103120743.110662-1-miaoqinglang@huawei.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
When updating the buffer demux, we will skip a scan element from the
device in the case `in_ind != out_ind` and we enter the while loop.
in_ind should only be refreshed with `find_next_bit()` in the end of the
loop.
Note, to cause problems we need a situation where we are skippig over
an element (channel not enabled) that happens to not have the same size
as the next element. Whilst this is a possible situation we haven't
actually identified any cases in mainline where it happens as most drivers
have consistent channel storage sizes with the exception of the timestamp
which is the last element and hence never skipped over.
Fixes: 5ada4ea9be16 ("staging:iio: add demux optionally to path from device to buffer") Signed-off-by: Nuno Sá <nuno.sa@analog.com> Link: https://lore.kernel.org/r/20201112144323.28887-1-nuno.sa@analog.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Commit 9816ef6ecbc1 ("scsi: lpfc: Use after free in lpfc_rq_buf_free()")
was made to correct a use after free condition in lpfc_rq_buf_free().
Unfortunately, a subsequent patch cut on a tree without the fix
inadvertently reverted the fix.
Put the fix back: Move the freeing of the rqb_entry to after the print
function that references it.
Link: https://lore.kernel.org/r/20201020202719.54726-4-james.smart@broadcom.com Fixes: 411de511c694 ("scsi: lpfc: Fix RQ empty firmware trap") Cc: <stable@vger.kernel.org> # v4.17+ Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
BUG: sleeping function called from invalid context at mm/slab.h:494
...
Call Trace:
dump_stack+0x9a/0xf0
___might_sleep.cold.63+0x13d/0x178
slab_pre_alloc_hook+0x6a/0x90
kmem_cache_alloc_trace+0x3a/0x2d0
lpfc_sli4_nvmet_alloc+0x4c/0x280 [lpfc]
lpfc_post_rq_buffer+0x2e7/0xa60 [lpfc]
lpfc_sli4_hba_setup+0x6b4c/0xa4b0 [lpfc]
lpfc_pci_probe_one_s4.isra.15+0x14f8/0x2280 [lpfc]
lpfc_pci_probe_one+0x260/0x2880 [lpfc]
local_pci_probe+0xd4/0x180
work_for_cpu_fn+0x51/0xa0
process_one_work+0x8f0/0x17b0
worker_thread+0x536/0xb50
kthread+0x30c/0x3d0
ret_from_fork+0x3a/0x50
A prior patch introduced a spin_lock_irqsave(hbalock) in the
lpfc_post_rq_buffer() routine. Call trace is seen as the hbalock is held
with interrupts disabled during a GFP_KERNEL allocation in
lpfc_sli4_nvmet_alloc().
Fix by reordering locking so that hbalock not held when calling
sli4_nvmet_alloc() (aka rqb_buf_list()).
Link: https://lore.kernel.org/r/20201020202719.54726-2-james.smart@broadcom.com Fixes: 411de511c694 ("scsi: lpfc: Fix RQ empty firmware trap") Cc: <stable@vger.kernel.org> # v4.17+ Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
After each codeword NAND_FLASH_STATUS is read for possible operational
failures. But there is no DMA sync for CPU operation before reading it
and this leads to incorrect or older copy of DMA buffer in reg_read_buf.
This patch adds the DMA sync on reg_read_buf for CPU before reading it.
Fixes: 5bc36b2bf6e2 ("mtd: rawnand: qcom: check for operation errors in case of raw read") Cc: stable@vger.kernel.org Signed-off-by: Praveenkumar I <ipkumar@codeaurora.org> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/1602230872-25616-1-git-send-email-ipkumar@codeaurora.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Some devices (especially QCA ones) are already using hardcoded partition
names with colons in it. The OpenMesh A62 for example provides following
mtd relevant information via cmdline:
Such a partition list cannot be parsed and thus the device fails to boot.
Avoid this behavior by making sure that the start of the first part-name
("(") will also be the last byte the mtd-id split algorithm is using for
its colon search.
Fixes: eb13fa022741 ("mtd: parser: cmdline: Support MTD names containing one or more colons") Cc: stable@vger.kernel.org Cc: Ron Minnich <rminnich@google.com> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20201124062506.185392-1-sven@narfation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
smp2p_update_bits() should disable interrupts when it acquires its
spinlock. This is important because without the _irqsave, a priority
inversion can occur.
This function is called both with interrupts enabled in
qcom_q6v5_request_stop(), and with interrupts disabled in
ipa_smp2p_panic_notifier(). IRQ handling of spinlocks should be
consistent to avoid the panic notifier deadlocking because it's
sitting on the thread that's already got the lock via _request_stop().
Found via lockdep.
Cc: stable@vger.kernel.org Fixes: 50e99641413e7 ("soc: qcom: smp2p: Qualcomm Shared Memory Point to Point") Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Evan Green <evgreen@chromium.org> Link: https://lore.kernel.org/r/20200929133040.RESEND.1.Ideabf6dcdfc577cf39ce3d95b0e4aa1ac8b38f0c@changeid Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Following error was seen when mounting a 16MByte ubifs:
UBIFS error (ubi0:0 pid 1893): check_lpt_type.constprop.6: invalid type (15) in LPT node type
QSPI_IFR.TFRTYP was not set correctly. When data transfer is enabled
and one wants to access the serial memory through AHB in order to:
- read in the serial memory, but not a memory data, for example
a JEDEC-ID, QSPI_IFR.TFRTYP must be written to '0' (both sama5d2
and sam9x60).
- read in the serial memory, and particularly a memory data,
TFRTYP must be written to '1' (both sama5d2 and sam9x60).
- write in the serial memory, but not a memory data, for example
writing the configuration or the QSPI_SR, TFRTYP must be written
to '2' for sama5d2 and to '0' for sam9x60.
- write in the serial memory in particular to program a memory data,
TFRTYP must be written to '3' for sama5d2 and to '1' for sam9x60.
Fix the setting of the QSPI_IFR.TFRTYP field.
Fixes: 2d30ac5ed633 ("mtd: spi-nor: atmel-quadspi: Use spi-mem interface for atmel-quadspi driver") Cc: <stable@vger.kernel.org> # v5.0+ Reported-by: Tom Burkart <tom@aussec.com> Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com> Link: https://lore.kernel.org/r/20201207135959.154124-2-tudor.ambarus@microchip.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
If the call to of_device_get_match_data() fails on probe of the Atmel
QuadSPI driver, the clock "aq->pclk" is erroneously not unprepared and
disabled. Fix it.
Fixes: 2e5c88887358 ("spi: atmel-quadspi: add support for sam9x60 qspi controller") Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: <stable@vger.kernel.org> # v5.1+ Cc: Tudor Ambarus <tudor.ambarus@microchip.com> Cc: Boris Brezillon <boris.brezillon@collabora.com> Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com> Link: https://lore.kernel.org/r/8f8dc2815aa97b2378528f08f923bf81e19611f0.1604874488.git.lukas@wunner.de Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
If the calls to device_reset() or devm_spi_register_controller() fail on
probe of the MediaTek MT7621 SPI driver, the spi_controller struct is
erroneously not freed. Fix by switching over to the new
devm_spi_alloc_master() helper.
Additionally, there's an ordering issue in mt7621_spi_remove() wherein
the spi_controller is unregistered after disabling the SYS clock.
The correct order is to call spi_unregister_controller() *before* this
teardown step because bus accesses may still be ongoing until that
function returns.
All of these bugs have existed since the driver was first introduced,
so it seems fair to fix them together in a single commit.
Commit 702b15cb9712 ("spi: mt7621: fix missing clk_disable_unprepare()
on error in mt7621_spi_probe") sought to disable the SYS clock on probe
errors, but only did so for 2 of 3 potentially failing calls: The clock
needs to be disabled on failure of devm_spi_register_controller() as
well.
Moreover, the commit purports to fix a bug in commit cbd66c626e16 ("spi:
mt7621: Move SPI driver out of staging") but in reality the bug has
existed since the driver was first introduced.
If the calls to platform_get_irq() or devm_request_irq() fail on probe
of the SynQuacer SPI driver, the clock "sspi->clk" is erroneously not
unprepared and disabled.
If the clock rate "master->max_speed_hz" cannot be determined, the same
happens and in addition the spi_master struct is not freed.
Fix it.
Fixes: b0823ee35cf9 ("spi: Add spi driver for Socionext SynQuacer platform") Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: <stable@vger.kernel.org> # v5.3+ Cc: Masahisa Kojima <masahisa.kojima@linaro.org> Link: https://lore.kernel.org/r/232281df1ab91d8f0f553a62d5f97fc264ace4da.1604874488.git.lukas@wunner.de Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
If the calls to devm_platform_ioremap_resource(), irq_of_parse_and_map()
or devm_request_irq() fail on probe of the ST SSC4 SPI driver, the
runtime PM disable depth is incremented even though it was not
decremented before. Fix it.
If the calls to devm_clk_get(), devm_spi_register_master() or
clk_prepare_enable() fail on probe of the Mikrotik RB4xx SPI driver,
the spi_master struct is erroneously not freed.
Fix by switching over to the new devm_spi_alloc_master() helper.
If the calls to devm_request_irq() or devm_spi_register_master() fail
on probe of the PIC32 SPI driver, the DMA channels requested by
pic32_spi_dma_prep() are erroneously not released. Plug the leak.
If the call to devm_spi_register_master() fails on probe of the GPIO SPI
driver, the spi_master struct is erroneously not freed:
After allocating the spi_master, its reference count is 1. The driver
unconditionally decrements the reference count on unbind using a devm
action. Before calling devm_spi_register_master(), the driver
unconditionally increments the reference count because on success,
that function will decrement the reference count on unbind. However on
failure, devm_spi_register_master() does *not* decrement the reference
count, so the spi_master is leaked.
The issue was introduced by commits 8b797490b4db ("spi: gpio: Make sure
spi_master_put() is called in every error path") and 79567c1a321e ("spi:
gpio: Use devm_spi_register_master()"), which sought to plug leaks
introduced by 9b00bc7b901f ("spi: spi-gpio: Rewrite to use GPIO
descriptors") but missed this remaining leak.
The situation was later aggravated by commit d3b0ffa1d75d ("spi: gpio:
prevent memory leak in spi_gpio_probe"), which introduced a
use-after-free because it releases a reference on the spi_master if
devm_add_action_or_reset() fails even though the function already
does that.
Fix by switching over to the new devm_spi_alloc_master() helper.
Fixes: 9b00bc7b901f ("spi: spi-gpio: Rewrite to use GPIO descriptors") Signed-off-by: Lukas Wunner <lukas@wunner.de> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Cc: <stable@vger.kernel.org> # v4.17+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation Cc: <stable@vger.kernel.org> # v5.1-: 8b797490b4db: spi: gpio: Make sure spi_master_put() is called in every error path Cc: <stable@vger.kernel.org> # v5.1-: 45beec351998: spi: bitbang: Introduce spi_bitbang_init() Cc: <stable@vger.kernel.org> # v5.1-: 79567c1a321e: spi: gpio: Use devm_spi_register_master() Cc: <stable@vger.kernel.org> # v5.4-: d3b0ffa1d75d: spi: gpio: prevent memory leak in spi_gpio_probe Cc: <stable@vger.kernel.org> # v4.17+ Cc: Navid Emamdoost <navid.emamdoost@gmail.com> Cc: Andrey Smirnov <andrew.smirnov@gmail.com> Link: https://lore.kernel.org/r/86eaed27431c3d709e3748eb76ceecbfc790dd37.1607286887.git.lukas@wunner.de Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Commit 0f0581b24bd0 ("spi: fsl: Convert to use CS GPIO descriptors")
broke the use of the SPISEL_BOOT signal as a chip select on the
MPC8309.
pdata->max_chipselect, which becomes master->num_chipselect, must be
initialized to take into account the possibility that there's one more
chip select in use than the number of GPIO chip selects.
Cc: stable@vger.kernel.org # v5.4+ Cc: Christophe Leroy <christophe.leroy@c-s.fr> Cc: Linus Walleij <linus.walleij@linaro.org> Fixes: 0f0581b24bd0 ("spi: fsl: Convert to use CS GPIO descriptors") Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Link: https://lore.kernel.org/r/20201127152947.376-1-rasmus.villemoes@prevas.dk Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
atmel_qspi_remove() accesses the driver's private data after calling
spi_unregister_controller() even though that function releases the last
reference on the spi_controller and thereby frees the private data.
Fix by switching over to the new devm_spi_alloc_master() helper which
keeps the private data accessible until the driver has unbound.
Fixes: 2d30ac5ed633 ("mtd: spi-nor: atmel-quadspi: Use spi-mem interface for atmel-quadspi driver") Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: <stable@vger.kernel.org> # v5.0+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation Cc: <stable@vger.kernel.org> # v5.0+ Cc: Piotr Bugalski <bugalski.piotr@gmail.com> Link: https://lore.kernel.org/r/4b05c65cf6f1ea3251484fe9a00b4c65478a1ae3.1607286887.git.lukas@wunner.de Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
spi_sh_remove() accesses the driver's private data after calling
spi_unregister_master() even though that function releases the last
reference on the spi_master and thereby frees the private data.
Fix by switching over to the new devm_spi_alloc_master() helper which
keeps the private data accessible until the driver has unbound.
Fixes: 680c1305e259 ("spi/spi_sh: use spi_unregister_master instead of spi_master_put in remove path") Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: <stable@vger.kernel.org> # v3.0+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation Cc: <stable@vger.kernel.org> # v3.0+ Cc: Axel Lin <axel.lin@ingics.com> Link: https://lore.kernel.org/r/6d97628b536baf01d5e3e39db61108f84d44c8b2.1607286887.git.lukas@wunner.de Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
pxa2xx_spi_remove() accesses the driver's private data after calling
spi_unregister_controller() even though that function releases the last
reference on the spi_controller and thereby frees the private data.
Fix by switching over to the new devm_spi_alloc_master/slave() helper
which keeps the private data accessible until the driver has unbound.
When inserting a VMA, we restrict the placement to the low 4G unless the
caller opts into using the full range. This was done to allow usersapce
the opportunity to transition slowly from a 32b address space, and to
avoid breaking inherent 32b assumptions of some commands.
However, for insert we limited ourselves to 4G-4K, but on verification
we allowed the full 4G. This causes some attempts to bind a new buffer
to sporadically fail with -ENOSPC, but at other times be bound
successfully.
commit 48ea1e32c39d ("drm/i915/gen9: Set PIN_ZONE_4G end to 4GB - 1
page") suggests that there is a genuine problem with stateless addressing
that cannot utilize the last page in 4G and so we purposefully excluded
it. This means that the quick pin pass may cause us to utilize a buggy
placement.
Reported-by: CQ Tang <cq.tang@intel.com>
Testcase: igt/gem_exec_params/larger-than-life-batch Fixes: 48ea1e32c39d ("drm/i915/gen9: Set PIN_ZONE_4G end to 4GB - 1 page") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: CQ Tang <cq.tang@intel.com> Reviewed-by: CQ Tang <cq.tang@intel.com> Reviewed-by: Matthew Auld <matthew.auld@intel.com> Cc: <stable@vger.kernel.org> # v4.5+ Link: https://patchwork.freedesktop.org/patch/msgid/20201216092951.7124-1-chris@chris-wilson.co.uk
(cherry picked from commit 5f22cc0b134ab702d7f64b714e26018f7288ffee) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
I observed this when unplugging a DP monitor whilst a computer is asleep
and then waking it up. This left DP chardev nodes still being present on
the filesystem and accessing these device nodes caused an oops because
drm_dp_aux_dev_get_by_minor() assumes a device exists if it is opened.
This can also be reproduced by creating a device node with mknod(1) and
issuing an open(2)
EDID parsing in S3 resume pushes new display modes
to probed_modes list but doesn't consolidate to actual
mode list. This creates a race condition when
amdgpu_dm_connector_ddc_get_modes() re-initializes the
list head without walking the list and results in memory leak.
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=209987 Acked-by: Harry Wentland <harry.wentland@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Stylon Wang <stylon.wang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The only reference to the mlxplat_mlxcpld_psu[] array got removed,
so there is now a warning from clang:
drivers/platform/x86/mlx-platform.c:322:30: error: variable 'mlxplat_mlxcpld_psu' is not needed and will not be emitted [-Werror,-Wunneeded-internal-declaration]
static struct i2c_board_info mlxplat_mlxcpld_psu[] = {
Remove the array as well and adapt the ARRAY_SIZE() call
accordingly.
Bounds checking tools can flag a bug in dbAdjTree() for an array index
out of bounds in dmt_stree. Since dmt_stree can refer to the stree in
both structures dmaptree and dmapctl, use the larger array to eliminate
the false positive.
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com> Reported-by: butt3rflyh4ck <butterflyhuangxx@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The jffs2 mount options will be ignored when remounting jffs2.
It can be easily reproduced with the steps listed below.
1. mount -t jffs2 -o compr=none /dev/mtdblockx /mnt
2. mount -o remount compr=zlib /mnt
Since ec10a24f10c8, the option parsing happens before fill_super and
then pass fc, which contains the options parsing results, to function
jffs2_reconfigure during remounting. But function jffs2_reconfigure do
not update c->mount_opts.
This patch add a function jffs2_update_mount_opts to fix this problem.
By the way, I notice that tmpfs use the same way to update remounting
options. If it is necessary to unify them?
Cc: <stable@vger.kernel.org> Fixes: ec10a24f10c8 ("vfs: Convert jffs2 to use the new mount API") Signed-off-by: lizhe <lizhe67@huawei.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The log of this problem is:
jffs2: Error garbage collecting node at 0x***!
jffs2: No space for garbage collection. Aborting GC thread
This is because GC believe that it do nothing, so it abort.
After going over the image of jffs2, I find a scene that
can trigger this problem stably.
The scene is: there is a normal dirent node at summary-area,
but abnormal at corresponding not-summary-area with error
name_crc.
The reason that GC exit abnormally is because it find that
abnormal dirent node to GC, but when it goes to function
jffs2_add_fd_to_list, it cannot meet the condition listed
below:
if ((*prev)->nhash == new->nhash && !strcmp((*prev)->name, new->name))
So no node is marked obsolete, statistical information of
erase_block do not change, which cause GC exit abnormally.
The root cause of this problem is: we do not check the
name_crc of the abnormal dirent node with summary is enabled.
Noticed that in function jffs2_scan_dirent_node, we use
function jffs2_scan_dirty_space to deal with the dirent
node with error name_crc. So this patch add a checking
code in function read_direntry to ensure the correctness
of dirent node. If checked failed, the dirent node will
be marked obsolete so GC will pass this node and this
problem will be fixed.
Cc: <stable@vger.kernel.org> Signed-off-by: Zhe Li <lizhe67@huawei.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Write buffers use a kmalloc()'ed buffer, they can leak
up to seven bytes of kernel memory to flash if writes are not
aligned.
So use ubifs_pad() to fill these gaps with padding bytes.
This was never a problem while scanning because the scanner logic
manually aligns node lengths and skips over these gaps.
Cc: <stable@vger.kernel.org> Fixes: 1e51764a3c2ac05a2 ("UBIFS: add new flash file system") Signed-off-by: Richard Weinberger <richard@nod.at> Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Mounts to Azure cause an unneeded warning message in dmesg
"CIFS: VFS: parse_server_interfaces: incomplete interface info"
Azure rounds up the size (by 8 additional bytes, to a
16 byte boundary) of the structure returned on the query
of the server interfaces at mount time. This is permissible
even though different than other servers so do not log a warning
if query network interfaces response is only rounded up by 8
bytes or fewer.
CC: Stable <stable@vger.kernel.org> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
A NULL pointer dereference may occur in __ceph_remove_cap with some of the
callbacks used in ceph_iterate_session_caps, namely trim_caps_cb and
remove_session_caps_cb. Those callers hold the session->s_mutex, so they
are prevented from concurrent execution, but ceph_evict_inode does not.
Since the callers of this function hold the i_ceph_lock, the fix is simply
a matter of returning immediately if caps->ci is NULL.
Cc: stable@vger.kernel.org
URL: https://tracker.ceph.com/issues/43272 Suggested-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Luis Henriques <lhenriques@suse.de> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Commit a408e4a86b36b ("ima: open a new file instance if no read
permissions") already introduced a second open to measure a file when the
original file descriptor does not allow it. However, it didn't remove the
existing method of changing the mode of the original file descriptor, which
is still necessary if the current process does not have enough privileges
to open a new one.
Changing the mode isn't really an option, as the filesystem might need to
do preliminary steps to make the read possible. Thus, this patch removes
the code and keeps the second open as the only option to measure a file
when it is unreadable with the original file descriptor.
Resulting quickly in a kernel crash. Let's properly protect using a
mutex.
Fixes: 9d5171a8f248 ("powerpc/powernv: Enable removal of memory for in memory tracing") Cc: stable@vger.kernel.org# v4.14+ Signed-off-by: David Hildenbrand <david@redhat.com> Reviewed-by: Oscar Salvador <osalvador@suse.de> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20201111145322.15793-3-david@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
We currently leak kernel memory to user space, because memory
offlining doesn't do any implicit clearing of memory and we are
missing explicit clearing of memory.
Let's keep it simple and clear pages before removing the linear
mapping.
Reproduced in QEMU/TCG with 10 GiB of main memory:
[root@localhost ~]# dd obs=9G if=/dev/urandom of=/dev/null
[... wait until "free -m" used counter no longer changes and cancel] 19665802+0 records in
1+0 records out 9663676416 bytes (9.7 GB, 9.0 GiB) copied, 135.548 s, 71.3 MB/s
[root@localhost ~]# cat /sys/devices/system/memory/block_size_bytes 40000000
[root@localhost ~]# echo 0x40000000 > /sys/kernel/debug/powerpc/memtrace/enable
[ 402.978663][ T1086] page:000000001bc4bc74 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x24900
[ 402.980063][ T1086] flags: 0x7ffff000001000(reserved)
[ 402.980415][ T1086] raw: 007ffff000001000c00c000000924008c00c0000009240080000000000000000
[ 402.980627][ T1086] raw: 0000000000000000000000000000000000000001ffffffff0000000000000000
[ 402.980845][ T1086] page dumped because: unmovable page
[ 402.989608][ T1086] Offlined Pages 16384
[ 403.324155][ T1086] memtrace: Allocated trace memory on node 0 at 0x0000000200000000
Before this patch:
[root@localhost ~]# hexdump -C /sys/kernel/debug/powerpc/memtrace/00000000/trace | head 00000000 c8 25 72 51 4d 26 36 c5 5c c2 56 15 d5 1a cd 10 |.%rQM&6.\.V.....| 00000010 19 b9 50 b2 cb e3 60 b8 ec 0a f3 ec 4b 3c 39 f0 |..P...`.....K<9.|$ 00000020 4e 5a 4c cf bd 26 19 ff 37 79 13 67 24 b7 b8 57 |NZL..&..7y.g$..W|$ 00000030 98 3e f5 be 6f 14 6a bd a4 52 bc 6e e9 e0 c1 5d |.>..o.j..R.n...]|$ 00000040 76 b3 ae b5 88 d7 da e3 64 23 85 2c 10 88 07 b6 |v.......d#.,....|$ 00000050 9a d8 91 de f7 50 27 69 2e 64 9c 6f d3 19 45 79 |.....P'i.d.o..Ey|$ 00000060 6a 6f 8a 61 71 19 1f c7 f1 df 28 26 ca 0f 84 55 |jo.aq.....(&...U|$ 00000070 01 3f be e4 e2 e1 da ff 7b 8c 8e 32 37 b4 24 53 |.?......{..27.$S|$ 00000080 1b 70 30 45 56 e6 8c c4 0e b5 4c fb 9f dd 88 06 |.p0EV.....L.....|$ 00000090 ef c4 18 79 f1 60 b1 5c 79 59 4d f4 36 d7 4a 5c |...y.`.\yYM.6.J\|$
After this patch:
[root@localhost ~]# hexdump -C /sys/kernel/debug/powerpc/memtrace/00000000/trace | head 00000000 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
* 40000000
Fixes: 9d5171a8f248 ("powerpc/powernv: Enable removal of memory for in memory tracing") Cc: stable@vger.kernel.org # v4.14+ Reported-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: David Hildenbrand <david@redhat.com> Reviewed-by: Oscar Salvador <osalvador@suse.de> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20201111145322.15793-2-david@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
We execute certain NPU2 setup code (such as mapping an LPID to a device
in NPU2) unconditionally if an Nvlink bridge is detected. However this
cannot succeed on POWER8NVL machines and errors appear in dmesg. This is
harmless as skiboot returns an error and the only place we check it is
vfio-pci but that code does not get called on P8+ either.
This adds a check if pnv_npu2_xxx helpers are called on a machine with
NPU2 which initializes pnv_phb::npu in pnv_npu2_init();
pnv_phb::npu==NULL on POWER8/NVL (Naples).
While at this, fix NULL derefencing in pnv_npu_peers_take_ownership/
pnv_npu_peers_release_ownership which occurs when GPUs on mentioned P8s
cause EEH which happens if "vfio-pci" disables devices using
the D3 power state; the vfio-pci's disable_idle_d3 module parameter
controls this and must be set on Naples. The EEH handling clears
the entire pnv_ioda_pe struct in pnv_ioda_free_pe() hence
the NULL derefencing. We cannot recover from that but at least we stop
crashing.
When SMC1 is relocated and early debug is selected, the
board hangs is ppc_md.setup_arch(). This is because ones
the microcode has been loaded and SMC1 relocated, early
debug writes in the weed.
To allow smooth continuation, the SMC1 parameter RAM set up
by the bootloader have to be copied into the new location.
Commit bd59380c5ba4 ("powerpc/rtas: Restrict RTAS requests from userspace")
introduced the following error when invoking the errinjct userspace
tool:
[root@ltcalpine2-lp5 librtas]# errinjct open
[327884.071171] sys_rtas: RTAS call blocked - exploit attempt?
[327884.071186] sys_rtas: token=0x26, nargs=0 (called by errinjct)
errinjct: Could not open RTAS error injection facility
errinjct: librtas: open: Unexpected I/O error
The entry for ibm,open-errinjct in rtas_filter array has a typo where
the "j" is omitted in the rtas call name. After fixing this typo the
errinjct tool functions again as expected.
The placeholder for instruction selection should use the second
argument's operand, which is %1, not %0. This could generate incorrect
assembly code if the memory addressing of operand %0 is a different
form from that of operand %1.
Also remove the %Un placeholder because having %Un placeholders
for two operands which are based on the same local var (ptep) doesn't
make much sense. By the way, it doesn't change the current behaviour
because "<>" constraint is missing for the associated "=m".
[chleroy: revised commit log iaw segher's comments and removed %U0]
Olga K. observed that rpcrdma_marsh_req() allocates sparse pages
only when it has determined that a Reply chunk is necessary. There
are plenty of cases where no Reply chunk is needed, but the
XDRBUF_SPARSE_PAGES flag is set. The result would be a crash in
rpcrdma_inline_fixup() when it tries to copy parts of the received
Reply into a missing page.
To avoid crashing, handle sparse page allocation up front.
Until XATTR support was added, this issue did not appear often
because the only SPARSE_PAGES consumer always expected a reply large
enough to always require a Reply chunk.
Reported-by: Olga Kornievskaia <kolga@netapp.com> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Cc: <stable@vger.kernel.org> Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
CAN0 and CAN1 instances share the same message ram configured
at 0x210000 on sama5d2 Linux systems.
According to current configuration of CAN0, we need 0x1c00 bytes
so that the CAN1 don't overlap its message ram:
64 x RX FIFO0 elements => 64 x 72 bytes
32 x TXE (TX Event FIFO) elements => 32 x 8 bytes
32 x TXB (TX Buffer) elements => 32 x 72 bytes
So a total of 7168 bytes (0x1C00).
Fix offset to match this needed size.
Make the CAN0 message ram ioremap match exactly this size so that is
easily understandable. Adapt CAN1 size accordingly.
Xattr code using inodes with large xattr data can end up dropping last
inode reference (and thus deleting the inode) from places like
ext4_xattr_set_entry(). That function is called with transaction started
and so ext4_evict_inode() can deadlock against fs freezing like:
CPU1 CPU2
removexattr() freeze_super()
vfs_removexattr()
ext4_xattr_set()
handle = ext4_journal_start()
...
ext4_xattr_set_entry()
iput(old_ea_inode)
ext4_evict_inode(old_ea_inode)
sb->s_writers.frozen = SB_FREEZE_FS;
sb_wait_write(sb, SB_FREEZE_FS);
ext4_freeze()
jbd2_journal_lock_updates()
-> blocks waiting for all
handles to stop
sb_start_intwrite()
-> blocks as sb is already in SB_FREEZE_FS state
Generally it is advisable to delete inodes from a separate transaction
as it can consume quite some credits however in this case it would be
quite clumsy and furthermore the credits for inode deletion are quite
limited and already accounted for. So just tweak ext4_evict_inode() to
avoid freeze protection if we have transaction already started and thus
it is not really needed anyway.
Cc: stable@vger.kernel.org Fixes: dec214d00e0d ("ext4: xattr inode deduplication") Signed-off-by: Jan Kara <jack@suse.cz> Reviewed-by: Andreas Dilger <adilger@dilger.ca> Link: https://lore.kernel.org/r/20201127110649.24730-1-jack@suse.cz Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
When freeing metadata, we will create an ext4_free_data and
insert it into the pending free list. After the current
transaction is committed, the object will be freed.
ext4_mb_free_metadata() will check whether the area to be freed
overlaps with the pending free list. If true, return directly. At this
time, ext4_free_data is leaked. Fortunately, the probability of this
problem is small, since it only occurs if the file system is corrupted
such that a block is claimed by more one inode and those inodes are
deleted within a single jbd2 transaction.
While fixing up our ->last_byte_to_unpin locking I noticed that we will
shorten len based on ->last_byte_to_unpin if we're caching when we're
adding back the free space. This is correct for the free space, as we
cannot unpin more than ->last_byte_to_unpin, however we use len to
adjust the ->bytes_pinned counters and such, which need to track the
actual pinned usage. This could result in
WARN_ON(space_info->bytes_pinned) triggering at unmount time.
Fix this by using a local variable for the amount to add to free space
cache, and leave len untouched in this case.
CC: stable@vger.kernel.org # 5.4+ Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The driver did not update its view of the available device buffer space
until write() was called in task context. This meant that write_room()
would return 0 even after the device had sent a write-unthrottle
notification, something which could lead to blocked writers not being
woken up (e.g. when using OPOST).
Note that we must also request an unthrottle notification is case a
write() request fills the device buffer exactly.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Cc: stable <stable@vger.kernel.org> Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The driver's transmit-unthrottle work was never flushed on disconnect,
something which could lead to the driver port data being freed while the
unthrottle work is still scheduled.
Fix this by cancelling the unthrottle work when shutting down the port.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Cc: stable@vger.kernel.org Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The driver's deferred write wakeup was never flushed on disconnect,
something which could lead to the driver port data being freed while the
wakeup work is still scheduled.
Fix this by using the usb-serial write wakeup which gets cancelled
properly on disconnect.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Cc: stable@vger.kernel.org Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Make sure to clear the write-busy flag also in case no new data was
submitted due to lack of device buffer space so that writing is
resumed once space again becomes available.
Fixes: 507ca9bc0476 ("[PATCH] USB: add ability for usb-serial drivers to determine if their write urb is currently being used.") Cc: stable <stable@vger.kernel.org> # 2.6.13 Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The write() callback can be called in interrupt context (e.g. when used
as a console) so interrupts must be disabled while holding the port lock
to prevent a possible deadlock.
Fixes: e81ee637e4ae ("usb-serial: possible irq lock inversion (PPP vs. usb/serial)") Fixes: 507ca9bc0476 ("[PATCH] USB: add ability for usb-serial drivers to determine if their write urb is currently being used.") Cc: stable <stable@vger.kernel.org> # 2.6.19 Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Commit c528fcb116e6 ("USB: serial: keyspan_pda: fix receive sanity
checks") broke write-unthrottle handling by dropping well-formed
unthrottle-interrupt packets which are precisely two bytes long. This
could lead to blocked writers not being woken up when buffer space again
becomes available.
Instead, stop unconditionally printing the third byte which is
(presumably) only valid on modem-line changes.
Fixes: c528fcb116e6 ("USB: serial: keyspan_pda: fix receive sanity checks") Cc: stable <stable@vger.kernel.org> # 4.11 Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The driver must not call tty_wakeup() while holding its private lock as
line disciplines are allowed to call back into write() from
write_wakeup(), leading to a deadlock.
Also remove the unneeded work struct that was used to defer wakeup in
order to work around a possible race in ancient times (see comment about
n_tty write_chan() in commit 14b54e39b412 ("USB: serial: remove
changelogs and old todo entries")).
The parallel-port restore operations is called when a driver claims the
port and is supposed to restore the provided state (e.g. saved when
releasing the port).
Fixes: b69578df7e98 ("USB: usbserial: mos7720: add support for parallel port on moschip 7715") Cc: stable <stable@vger.kernel.org> # 2.6.35 Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
One of our machines keeled over trying to rebuild the scheduler domains.
Mainline produces the same splat:
BUG: unable to handle page fault for address: 0000607f820054db
CPU: 2 PID: 149 Comm: kworker/1:1 Not tainted 5.10.0-rc1-master+ #6
Workqueue: events cpuset_hotplug_workfn
RIP: build_sched_domains
Call Trace:
partition_sched_domains_locked
rebuild_sched_domains_locked
cpuset_hotplug_workfn
It happens with cgroup2 and exclusive cpusets only. This reproducer
triggers it on an 8-cpu vm and works most effectively with no
preexisting child cgroups:
tl->mask(cpu), which reads cpu_sibling_map on x86, returns an empty mask
and so cpumask_first() returns >= nr_cpu_ids, which leads to the bogus
value from per_cpu_ptr() above.
The problem is a race between cpuset_hotplug_workfn() and a later
offline of CPU N. cpuset_hotplug_workfn() updates the effective masks
when N is still online, the offline clears N from cpu_sibling_map, and
then the worker uses the stale effective masks that still have N to
generate the scheduling domains, leading the worker to read
N's empty cpu_sibling_map in sd_init().
rebuild_sched_domains_locked() prevented the race during the cgroup2
cpuset series up until the Fixes commit changed its check. Make the
check more robust so that it can detect an offline CPU in any exclusive
cpuset's effective mask, not just the top one.
Fixes: 0ccea8feb980 ("cpuset: Make generate_sched_domains() work with partition") Signed-off-by: Daniel Jordan <daniel.m.jordan@oracle.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Tejun Heo <tj@kernel.org> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20201112171711.639541-1-daniel.m.jordan@oracle.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
In order to setup its PCI component, the driver needs any node private
instance in order to get a reference to the PCI device and hand that
into edac_pci_create_generic_ctl(). For convenience, it uses the 0th
memory controller descriptor under the assumption that if any, the 0th
will be always present.
However, this assumption goes wrong when the 0th node doesn't have
memory and the driver doesn't initialize an instance for it:
ARM Cortex-A57 and Cortex-A72 cores running in 32-bit mode are affected
by silicon errata #1742098 and #1655431, respectively, where the second
instruction of a AES instruction pair may execute twice if an interrupt
is taken right after the first instruction consumes an input register of
which a single 32-bit lane has been updated the last time it was modified.
This is not such a rare occurrence as it may seem: in counter mode, only
the least significant 32-bit word is incremented in the absence of a
carry, which makes our counter mode implementation susceptible to these
errata.
So let's shuffle the counter assignments around a bit so that the most
recent updates when the AES instruction pair executes are 128-bit wide.
ecdh_set_secret() casts a void* pointer to a const u64* in order to
feed it into ecc_is_key_valid(). This is not generally permitted by
the C standard, and leads to actual misalignment faults on ARMv6
cores. In some cases, these are fixed up in software, but this still
leads to performance hits that are entirely avoidable.
So let's copy the key into the ctx buffer first, which we will do
anyway in the common case, and which guarantees correct alignment.
Perf event attritube supports exclude_kernel flag to avoid
sampling/profiling in supervisor state (kernel). Based on this event
attr flag, Monitor Mode Control Register bit is set to freeze on
supervisor state. But sometimes (due to hardware limitation), Sampled
Instruction Address Register (SIAR) locks on to kernel address even
when freeze on supervisor is set. Patch here adds a check to drop
those samples.
According to the event list from icelake_core_v1.09.json, the encoding
of the RTM_RETIRED.ABORTED event on Ice Lake should be,
"EventCode": "0xc9",
"UMask": "0x04",
"EventName": "RTM_RETIRED.ABORTED",
The event CYCLE_ACTIVITY.STALLS_MEM_ANY (0x14a3) should be available on
all 8 GP counters on ICL, but it's only scheduled on the first four
counters due to the current ICL constraint table.
Add a line for the CYCLE_ACTIVITY.STALLS_MEM_ANY event in the ICL
constraint table.
Correct the comments for the CYCLE_ACTIVITY.CYCLES_MEM_ANY event.
I have had reports from two different people that attempts to read the
analog input channels of the MF624 board fail with an `ETIMEDOUT` error.
After triggering the conversion, the code calls `comedi_timeout()` with
`mf6x4_ai_eoc()` as the callback function to check if the conversion is
complete. The callback returns 0 if complete or `-EBUSY` if not yet
complete. `comedi_timeout()` returns `-ETIMEDOUT` if it has not
completed within a timeout period which is propagated as an error to the
user application.
The existing code considers the conversion to be complete when the EOLC
bit is high. However, according to the user manuals for the MF624 and
MF634 boards, this test is incorrect because EOLC is an active low
signal that goes high when the conversion is triggered, and goes low
when the conversion is complete. Fix the problem by inverting the test
of the EOLC bit state.
The cx2072x codec driver defines multiple DAIs with the same stream
name "Playback" and "Capture". Although the current code works more
or less as is as the secondary streams are never used, it still leads
the error message like:
debugfs: File 'Playback' in directory 'dapm' already present!
debugfs: File 'Capture' in directory 'dapm' already present!
Fix it by renaming the secondary streams to unique names.
Fixes: a497a4363706 ("ASoC: Add support for Conexant CX2072X CODEC") Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Link: https://lore.kernel.org/r/20201208135154.9188-1-tiwai@suse.de Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Add a per-transaction flag to indicate that the buffer
must be cleared when the transaction is complete to
prevent copies of sensitive data from being preserved
in memory.
In dasd_alias_disconnect_device_from_lcu the device is removed from any
list on the LCU. Afterwards the LCU is removed from the lcu list if it
does not contain devices any longer.
The lcu->lock protects the lcu from parallel updates. But to cancel all
workers and wait for completion the lcu->lock has to be unlocked.
If two devices are removed in parallel and both are removed from the LCU
the first device that takes the lcu->lock again will delete the LCU because
it is already empty but the second device also tries to free the LCU which
leads to a list corruption of the lcu list.
Fix by removing the device right before the lcu is checked without
unlocking the lcu->lock in between.
Fixes: 8e09f21574ea ("[S390] dasd: add hyper PAV support to DASD device driver, part 1") Cc: stable@vger.kernel.org Signed-off-by: Stefan Haberland <sth@linux.ibm.com> Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
dasd_alias_add_device() moves devices to the active_devices list in case
of a scheduled LCU update regardless if they have previously been in a
pavgroup or not.
Example: device A and B are in the same pavgroup.
Device A has already been in a pavgroup and the private->pavgroup pointer
is set and points to a valid pavgroup. While going through dasd_add_device
it is moved from the pavgroup to the active_devices list.
In parallel device B might be removed from the same pavgroup in
remove_device_from_lcu() which in turn checks if the group is empty
and deletes it accordingly because device A has already been removed from
there.
When now device A enters remove_device_from_lcu() it is tried to remove it
from the pavgroup again because the pavgroup pointer is still set and again
the empty group will be cleaned up which leads to a list corruption.
Fix by setting private->pavgroup to NULL in dasd_add_device.
If the device has been the last device on the pavgroup an empty pavgroup
remains but this will be cleaned up by the scheduled lcu_update which
iterates over all existing pavgroups.
Fixes: 8e09f21574ea ("[S390] dasd: add hyper PAV support to DASD device driver, part 1") Cc: stable@vger.kernel.org Signed-off-by: Stefan Haberland <sth@linux.ibm.com> Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Prevent _lcu_update from adding a device to a pavgroup if the LCU still
requires an update. The data is not reliable any longer and in parallel
devices might have been moved on the lists already.
This might lead to list corruptions or invalid PAV grouping.
Only add devices to a pavgroup if the LCU is up to date. Additional steps
are taken by the scheduled lcu update.
Fixes: 8e09f21574ea ("[S390] dasd: add hyper PAV support to DASD device driver, part 1") Cc: stable@vger.kernel.org Signed-off-by: Stefan Haberland <sth@linux.ibm.com> Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
For an LCU update a read unit address configuration IO is required.
This is started using sleep_on(), which has early exit paths in case the
device is not usable for IO. For example when it is in offline processing.
In those cases the LCU update should fail and not be retried.
Therefore lcu_update_work checks if EOPNOTSUPP is returned or not.
Commit 41995342b40c ("s390/dasd: fix endless loop after read unit address configuration")
accidentally removed the EOPNOTSUPP return code from
read_unit_address_configuration(), which in turn might lead to an endless
loop of the LCU update in offline processing.
Fix by returning EOPNOTSUPP again if the device is not able to perform the
request.
Fixes: 41995342b40c ("s390/dasd: fix endless loop after read unit address configuration") Cc: stable@vger.kernel.org #5.3 Signed-off-by: Stefan Haberland <sth@linux.ibm.com> Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
diag308 subcode 0 performes a clear reset which inlcudes the reset of
all registers in the system. While this is the preferred behavior when
loading a normal kernel via kexec it prevents the crash kernel to store
the register values in the dump. To prevent this use subcode 1 when
loading a crash kernel instead.
Fixes: ee337f5469fd ("s390/kexec_file: Add crash support to image loader") Cc: <stable@vger.kernel.org> # 4.17 Signed-off-by: Philipp Rudo <prudo@linux.ibm.com> Reported-by: Xiaoying Yan <yiyan@redhat.com> Tested-by: Lianbo Jiang <lijiang@redhat.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Not resetting the SMT siblings might leave them in unpredictable
state. One of the observed problems was that the CPU timer wasn't
reset and therefore large system time values where accounted during
CPU bringup.
Since mmap for userspace is based on page alignment, add page alignment
for iram alloc from pool, otherwise, some good data located in the same
page of dmab->area maybe touched wrongly by userspace like pulseaudio.
Signed-off-by: Robin Gong <yibin.gong@nxp.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/1608221747-3474-1-git-send-email-yibin.gong@nxp.com Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Some buggy firmware don't give the current sample rate but leaves
zero. Handle this case more gracefully without warning but just skip
the current rate verification from the next time.
The Quanta NL3 laptop has both a headphone output jack and a headset
jack, on the right edge of the chassis.
The pin information suggests that both of these are at the Front.
The PulseAudio is confused to differentiate them so one of the jack
can neither get the jack sense working nor the audio output.
The ALC269_FIXUP_LIFEBOOK chained with ALC269_FIXUP_QUANTA_MUTE can
help to differentiate 2 jacks and get the 'Auto-Mute Mode' working
correctly.
This Acer Veriton N4640G/N6640G/N2510G desktops have 2 headphone
jacks(front and rear), and a separate Mic In jack.
The rear headphone jack is actually a line out jack but always silent
while playing audio. The front 'Mic In' also fails the jack sensing.
Apply the ALC269_FIXUP_LIFEBOOK to have all audio jacks to work as
expected.
Signed-off-by: Chris Chiu <chiu@endlessos.org> Signed-off-by: Jian-Hong Pan <jhp@endlessos.org> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20201222150459.9545-2-chiu@endlessos.org Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
There are a few places that call round{up|down}_pow_of_two() with the
value zero, and this causes undefined behavior warnings. Avoid
calling those macros if such a nonsense value is passed; it's a minor
optimization as well, as we handle it as either an error or a value to
be skipped, instead.