While vb2_mmap took the mmap_lock mutex, vb2_get_unmapped_area didn't.
Add this.
Also take this opportunity to move the 'q->memory != VB2_MEMORY_MMAP'
check and vb2_fileio_is_active() check into __find_plane_by_offset() so
both vb2_mmap and vb2_get_unmapped_area do the same checks.
Since q->memory is checked while mmap_lock is held, also take that lock
in reqbufs and create_bufs when it is set, and set it back to
MEMORY_UNKNOWN on error.
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So remove kfree_skb()
from the spin_lock_irqsave() section and use the already existing
"drop" label in xenvif_start_xmit() for dropping the SKB. At the
same time replace the dev_kfree_skb() call there with a call of
dev_kfree_skb_any(), as xenvif_start_xmit() can be called with
disabled interrupts.
This is XSA-424 / CVE-2022-42328 / CVE-2022-42329.
Fixes: be81992f9086 ("xen/netback: don't queue unlimited number of packages") Reported-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 5d0fa6fc8899fe842329c0109f8ddd01144b1ed8) Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
In some cases, the frontend may send a packet where the protocol headers
are spread across multiple slots. This would result in netback creating
an skb where the protocol headers spill over into the non-linear area.
Some drivers and NICs don't handle this properly resulting in an
interface reset or worse.
This issue was introduced by the removal of an unconditional skb pull in
the tx path to improve performance. Fix this without reintroducing the
pull by setting up grant copy ops for as many slots as needed to reach
the XEN_NETBACK_TX_COPY_LEN size. Adjust the rest of the code to handle
multiple copy operations per skb.
This is XSA-423 / CVE-2022-3643.
Fixes: 7e5d7753956b ("xen-netback: remove unconditional __pskb_pull_tail() in guest Tx path") Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com> Reviewed-by: Paul Durrant <paul@xen.org> Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 0fe29bd92594a747a2561589bd452c259451929e) Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
edid_read() was assumed to return 0 on success. After commit 7f16d0f3b8e2("drm/bridge: anx7625: Propagate errors from sp_tx_rst_aux()"),
the function will return > 0 for successful case, representing the i2c
read bytes. Otherwise -EIO on failure cases. Update the g_edid_break
break condition accordingly.
Fixes: 7f16d0f3b8e2("drm/bridge: anx7625: Propagate errors from sp_tx_rst_aux()") Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org> Reviewed-by: Robert Foss <robert.foss@linaro.org> Reviewed-by: Xin Ji <xji@analogixsemi.com> Signed-off-by: Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20211118193002.407168-1-hsinyi@chromium.org Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit f01677be31d1d52f2330f6f94d6bd943b9317692) Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
`hostname` needs to be set as null-pointer after free in
`cifs_put_tcp_session` function, or when `cifsd` thread attempts
to resolve hostname and reconnect the host, the thread would deref
the invalid pointer.
Here is one of practical backtrace examples as reference:
cifsd
---------------------------
kthread
cifs_demultiplex_thread
cifs_reconnect
reconn_set_ipaddr_from_hostname
--> if (!server->hostname)
--> if (server->hostname[0] == '\0') // !! UAF fault here
CIFS: VFS: cifs_mount failed w/return code = -112
mount error(112): Host is down
BUG: KASAN: use-after-free in reconn_set_ipaddr_from_hostname+0x2ba/0x310
Read of size 1 at addr ffff888108f35380 by task cifsd/480
CPU: 2 PID: 480 Comm: cifsd Not tainted 6.1.0-rc2-00106-gf705792f89dd-dirty #25
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x68/0x85
print_report+0x16c/0x4a3
kasan_report+0x95/0x190
reconn_set_ipaddr_from_hostname+0x2ba/0x310
__cifs_reconnect.part.0+0x241/0x800
cifs_reconnect+0x65f/0xb60
cifs_demultiplex_thread+0x1570/0x2570
kthread+0x2c5/0x380
ret_from_fork+0x22/0x30
</TASK>
Allocated by task 477:
kasan_save_stack+0x1e/0x40
kasan_set_track+0x21/0x30
__kasan_kmalloc+0x7e/0x90
__kmalloc_node_track_caller+0x52/0x1b0
kstrdup+0x3b/0x70
cifs_get_tcp_session+0xbc/0x19b0
mount_get_conns+0xa9/0x10c0
cifs_mount+0xdf/0x1970
cifs_smb3_do_mount+0x295/0x1660
smb3_get_tree+0x352/0x5e0
vfs_get_tree+0x8e/0x2e0
path_mount+0xf8c/0x1990
do_mount+0xee/0x110
__x64_sys_mount+0x14b/0x1f0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Freed by task 477:
kasan_save_stack+0x1e/0x40
kasan_set_track+0x21/0x30
kasan_save_free_info+0x2a/0x50
__kasan_slab_free+0x10a/0x190
__kmem_cache_free+0xca/0x3f0
cifs_put_tcp_session+0x30c/0x450
cifs_mount+0xf95/0x1970
cifs_smb3_do_mount+0x295/0x1660
smb3_get_tree+0x352/0x5e0
vfs_get_tree+0x8e/0x2e0
path_mount+0xf8c/0x1990
do_mount+0xee/0x110
__x64_sys_mount+0x14b/0x1f0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
The buggy address belongs to the object at ffff888108f35380
which belongs to the cache kmalloc-16 of size 16
The buggy address is located 0 bytes inside of
16-byte region [ffff888108f35380, ffff888108f35390)
The buggy address belongs to the physical page:
page:00000000333f8e58 refcount:1 mapcount:0 mapping:0000000000000000 index:0xffff888108f350e0 pfn:0x108f35
flags: 0x200000000000200(slab|node=0|zone=2)
raw: 02000000000002000000000000000000dead000000000122ffff8881000423c0
raw: ffff888108f350e0000000008080007a00000001ffffffff0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address: ffff888108f35280: fa fb fc fc fa fb fc fc fa fb fc fc fa fb fc fc ffff888108f35300: fa fb fc fc fa fb fc fc fa fb fc fc fa fb fc fc
>ffff888108f35380: fa fb fc fc fa fb fc fc fa fb fc fc fa fb fc fc
^ ffff888108f35400: fa fb fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff888108f35480: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
Fixes: 7be3248f3139 ("cifs: To match file servers, make sure the server hostname matches") Signed-off-by: Zeng Heng <zengheng4@huawei.com> Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit ee2536830b161d16859b2771effdde6b819c253f) Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
Some Intel chipsets disconnect the time and date RTC registers when the
clock update is in progress: during this time reads may return bogus
values and writes fail silently. This includes the RTC alarm registers.
[1]
cmos_read_alarm() did not take account for that, which caused alarm time
reads to sometimes return bogus values. This can be shown with a test
patch that I am attaching to this patch series.
Fix this, by using mc146818_avoid_UIP().
[1] 7th Generation Intel ® Processor Family I/O for U/Y Platforms [...]
Datasheet, Volume 1 of 2 (Intel's Document Number: 334658-006)
Page 208
https://www.intel.com/content/dam/www/public/us/en/documents/datasheets/7th-and-8th-gen-core-family-mobile-u-y-processor-lines-i-o-datasheet-vol-1.pdf
"If a RAM read from the ten time and date bytes is attempted
during an update cycle, the value read do not necessarily
represent the true contents of those locations. Any RAM writes
under the same conditions are ignored."
Some Intel chipsets disconnect the time and date RTC registers when the
clock update is in progress: during this time reads may return bogus
values and writes fail silently. This includes the RTC alarm registers.
[1]
cmos_set_alarm() did not take account for that, fix it.
[1] 7th Generation Intel ® Processor Family I/O for U/Y Platforms [...]
Datasheet, Volume 1 of 2 (Intel's Document Number: 334658-006)
Page 208
https://www.intel.com/content/dam/www/public/us/en/documents/datasheets/7th-and-8th-gen-core-family-mobile-u-y-processor-lines-i-o-datasheet-vol-1.pdf
"If a RAM read from the ten time and date bytes is attempted
during an update cycle, the value read do not necessarily
represent the true contents of those locations. Any RAM writes
under the same conditions are ignored."
Function mc146818_get_time() contains an elaborate mechanism of reading
the RTC time while no RTC update is in progress. It turns out that
reading the RTC alarm clock also requires avoiding the RTC update.
Therefore, the mechanism in mc146818_get_time() should be reused - so
extract it into a separate function.
The logic in mc146818_avoid_UIP() is same as in mc146818_get_time()
except that after every
if (CMOS_READ(RTC_FREQ_SELECT) & RTC_UIP) {
there is now "mdelay(1)".
To avoid producing a very unreadable patch, mc146818_get_time() will be
refactored to use mc146818_avoid_UIP() in the next patch.
Any codepath that zaps page table entries must invoke MMU notifiers to
ensure that secondary MMUs (like KVM) don't keep accessing pages which
aren't mapped anymore. Secondary MMUs don't hold their own references to
pages that are mirrored over, so failing to notify them can lead to page
use-after-free.
I'm marking this as addressing an issue introduced in commit f3f0e1d2150b
("khugepaged: add support of collapse for tmpfs/shmem pages"), but most of
the security impact of this only came in commit 27e1f8273113 ("khugepaged:
enable collapse pmd for pte-mapped THP"), which actually omitted flushes
for the removal of present PTEs, not just for the removal of empty page
tables.
Since commit 70cbc3cc78a99 ("mm: gup: fix the fast GUP race against THP
collapse"), the lockless_pages_from_mm() fastpath rechecks the pmd_t to
ensure that the page table was not removed by khugepaged in between.
However, lockless_pages_from_mm() still requires that the page table is
not concurrently freed. Fix it by sending IPIs (if the architecture uses
semi-RCU-style page table freeing) before freeing/reusing page tables.
pagetable walks on address ranges mapped by VMAs can be done under the
mmap lock, the lock of an anon_vma attached to the VMA, or the lock of the
VMA's address_space. Only one of these needs to be held, and it does not
need to be held in exclusive mode.
Under those circumstances, the rules for concurrent access to page table
entries are:
- Terminal page table entries (entries that don't point to another page
table) can be arbitrarily changed under the page table lock, with the
exception that they always need to be consistent for
hardware page table walks and lockless_pages_from_mm().
This includes that they can be changed into non-terminal entries.
- Non-terminal page table entries (which point to another page table)
can not be modified; readers are allowed to READ_ONCE() an entry, verify
that it is non-terminal, and then assume that its value will stay as-is.
Retracting a page table involves modifying a non-terminal entry, so
page-table-level locks are insufficient to protect against concurrent page
table traversal; it requires taking all the higher-level locks under which
it is possible to start a page walk in the relevant range in exclusive
mode.
The collapse_huge_page() path for anonymous THP already follows this rule,
but the shmem/file THP path was getting it wrong, making it possible for
concurrent rmap-based operations to cause corruption.
LARA-L6 module can be configured (by AT interface) in three different
USB modes:
* Default mode (Vendor ID: 0x1546 Product ID: 0x1341) with 4 serial
interfaces
* RmNet mode (Vendor ID: 0x1546 Product ID: 0x1342) with 4 serial
interfaces and 1 RmNet virtual network interface
* CDC-ECM mode (Vendor ID: 0x1546 Product ID: 0x1343) with 4 serial
interface and 1 CDC-ECM virtual network interface
In RmNet mode LARA-L6 exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parset/alternative functions
If 4: RMNET interface
Signed-off-by: Davide Tronchin <davide.tronchin.94@gmail.com> Acked-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 26f084e554669b203ef33c2f753a9629d77c2823) Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
trans_xen did not check the data fits into the buffer before copying
from the xen ring, but we probably should.
Add a check that just skips the request and return an error to
userspace if it did not fit
If there's a disconnection while operating in eSS, there may be a delay
in VBUS drop response from the connector. In that case, the internal
link state may drop to operate in usb2 speed while the controller thinks
the VBUS is still high. The driver must make sure to disable
GUSB2PHYCFG.SUSPHY when sending endpoint command while in usb2 speed.
The End Transfer command may be called, and only that command needs to
go through at this point. Let's keep it simple and unconditionally
disable GUSB2PHYCFG.SUSPHY whenever we issue the command.
This scenario is not seen in real hardware. In a rare case, our
prototype type-c controller/interface may have a slow response
triggerring this issue.
Status is reported as always off in the 6032 case. Status
reporting now matches the logic in the setters. Once of
the differences to the 6030 is that there are no groups,
therefore the state needs to be read out in the lower bits.
When trying to see if we can clone a file range, there are cases where we
end up sending two write operations in case the inode from the source root
has an i_size that is not sector size aligned and the length from the
current offset to its i_size is less than the remaining length we are
trying to clone.
Issuing two write operations when we could instead issue a single write
operation is not incorrect. However it is not optimal, specially if the
extents are compressed and the flag BTRFS_SEND_FLAG_COMPRESSED was passed
to the send ioctl. In that case we can end up sending an encoded write
with an offset that is not sector size aligned, which makes the receiver
fallback to decompressing the data and writing it using regular buffered
IO (so re-compressing the data in case the fs is mounted with compression
enabled), because encoded writes fail with -EINVAL when an offset is not
sector size aligned.
The following example, which triggered a bug in the receiver code for the
fallback logic of decompressing + regular buffer IO and is fixed by the
patchset referred in a Link at the bottom of this changelog, is an example
where we have the non-optimal behaviour due to an unaligned encoded write:
$ cat test.sh
#!/bin/bash
DEV=/dev/sdj
MNT=/mnt/sdj
mkfs.btrfs -f $DEV > /dev/null
mount -o compress $DEV $MNT
# File foo has a size of 33K, not aligned to the sector size.
xfs_io -f -c "pwrite -S 0xab 0 33K" $MNT/foo
xfs_io -f -c "pwrite -S 0xcd 0 64K" $MNT/bar
# Now clone the first 32K of file bar into foo at offset 0.
xfs_io -c "reflink $MNT/bar 0 0 32K" $MNT/foo
# Snapshot the default subvolume and create a full send stream (v2).
btrfs subvolume snapshot -r $MNT $MNT/snap
echo -e "\nFile bar in the original filesystem:"
od -A d -t x1 $MNT/snap/bar
umount $MNT
mkfs.btrfs -f $DEV > /dev/null
mount $DEV $MNT
echo -e "\nReceiving stream in a new filesystem..."
btrfs receive -f /tmp/test.send $MNT
echo -e "\nFile bar in the new filesystem:"
od -A d -t x1 $MNT/snap/bar
umount $MNT
Before this patch, the send stream included one regular write and one
encoded write for file 'bar', with the later being not sector size aligned
and causing the receiver to fallback to decompression + buffered writes.
The output of the btrfs receive command in verbose mode (-vvv):
(...)
mkfile o258-7-0
rename o258-7-0 -> bar
utimes
clone bar - source=foo source offset=0 offset=0 length=32768
write bar - offset=32768 length=1024
encoded_write bar - offset=33792, len=4096, unencoded_offset=33792, unencoded_file_len=31744, unencoded_len=65536, compression=1, encryption=0
encoded_write bar - falling back to decompress and write due to errno 22 ("Invalid argument")
(...)
This patch avoids the regular write followed by an unaligned encoded write
so that we end up sending a single encoded write that is aligned. So after
this patch the stream content is (output of btrfs receive -vvv):
(...)
mkfile o258-7-0
rename o258-7-0 -> bar
utimes
clone bar - source=foo source offset=0 offset=0 length=32768
encoded_write bar - offset=32768, len=4096, unencoded_offset=32768, unencoded_file_len=32768, unencoded_len=65536, compression=1, encryption=0
(...)
So we get more optimal behaviour and avoid the silent data loss bug in
versions of btrfs-progs affected by the bug referred by the Link tag
below (btrfs-progs v5.19, v5.19.1, v6.0 and v6.0.1).
The `nettest` binary, built from `selftests/net/nettest.c`,
was expected to be found in the path during test execution of
`fcnal-test.sh` and `pmtu.sh`, leading to tests getting
skipped when the binary is not installed in the system, as can
be seen in these logs found in the wild [1]:
# TEST: vti4: PMTU exceptions [SKIP]
[ 350.600250] IPv6: ADDRCONF(NETDEV_CHANGE): veth_b: link becomes ready
[ 350.607421] IPv6: ADDRCONF(NETDEV_CHANGE): veth_a: link becomes ready
# 'nettest' command not found; skipping tests
# xfrm6udp not supported
# TEST: vti6: PMTU exceptions (ESP-in-UDP) [SKIP]
[ 351.605102] IPv6: ADDRCONF(NETDEV_CHANGE): veth_b: link becomes ready
[ 351.612243] IPv6: ADDRCONF(NETDEV_CHANGE): veth_a: link becomes ready
# 'nettest' command not found; skipping tests
# xfrm4udp not supported
The `unicast_extensions.sh` tests also rely on `nettest`, but
it runs fine there because it looks for the binary in the
current working directory [2]:
The same mechanism that works for the Unicast extensions tests
is here copied over to the PMTU and functional tests.
Signed-off-by: Daniel Díaz <daniel.diaz@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit f54e1edf579d7f58476c57de97f85abaa7b97bc0) Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed.
seq_copy_in_user() and seq_copy_in_kernel() did not have prototypes
matching snd_seq_dump_func_t. Adjust this and remove the casts. There
are not resulting binary output differences.
This was found as a result of Clang's new -Wcast-function-type-strict
flag, which is more sensitive than the simpler -Wcast-function-type,
which only checks for type width mismatches.
Sony's downstream driver [1], among some other changes, adds a
seemingly random 10ms usleep_range, which turned out to be necessary
for the hardware to function properly on at least Sony Xperia 1 IV.
Without this, I2C transactions with the SLG51000 straight up fail.
Relax (10-10ms -> 10-11ms) and add the aforementioned sleep to make
sure the hardware has some time to wake up.
Due to the hardware behavior, it takes some time for CBJ detection/impedance sensing/de-bounce.
The ClockStop_NotFinished flag will be raised until these functions are completed.
In ClockStopMode0 mode case, the SdW controller might check this flag from D3 to D0 when the
jack detection interrupt happened.
The clock source and the sched_clock provided by the arm_global_timer
on Rockchip rk3066a/rk3188 are quite unstable because their rates
depend on the CPU frequency.
Recent changes to the arm_global_timer driver makes it impossible to use.
On the other side, the arm_global_timer has a higher rating than the
ROCKCHIP_TIMER, it will be selected by default by the time framework
while we want to use the stable Rockchip clock source.
Keep the arm_global_timer disabled in order to have the
DW_APB_TIMER (rk3066a) or ROCKCHIP_TIMER (rk3188) selected by default.
A DEVAPC violation occurs when removing the module
due to accessing HW registers without base clock.
To fix this bug, the correct method is:
1. Call the runtime resume function to enable the
clock;
2. Operate the registers to reset the HW;
3. Turn off the clocks and disable the device
RPM mechanism.
DSPCLK_DIV field in WM8962_CLOCKING1 register is used to generate
correct frequency of LRCLK and BCLK. Sometimes the read-only value
can't be updated timely after enabling SYSCLK. This results in wrong
calculation values. Delay is introduced here to wait for newest value
from register. The time of the delay should be at least 500~1000us
according to test.
Actually in no-MMU SoCs(i.e. i.MXRT) ZERO_PAGE(vaddr) expands to
```
virt_to_page(0)
```
that in order expands to:
```
pfn_to_page(virt_to_pfn(0))
```
and then virt_to_pfn(0) to:
```
((((unsigned long)(0) - PAGE_OFFSET) >> PAGE_SHIFT) +
PHYS_PFN_OFFSET)
```
where PAGE_OFFSET and PHYS_PFN_OFFSET are the DRAM offset(0x80000000) and
PAGE_SHIFT is 12. This way we obtain 16MB(0x01000000) summed to the base of
DRAM(0x80000000).
When ZERO_PAGE(0) is then used, for example in bio_add_page(), the page
gets an address that is out of DRAM bounds.
So instead of using fake virtual page 0 let's allocate a dedicated
zero_page during paging_init() and assign it to a global 'struct page *
empty_zero_page' the same way mmu.c does and it's the same approach used
in m68k with commit dc068f462179 as discussed here[0]. Then let's move
ZERO_PAGE() definition to the top of pgtable.h to be in common between
mmu.c and nommu.c.
Store the frame address where arm_get_current_stackframe() looks for it
(ARM_r7 instead of ARM_fp if CONFIG_THUMB2_KERNEL=y). Otherwise frame->fp
gets set to 0, causing unwind_frame() to fail.
We must prevent the CPU from reordering the files->count read with the
FD table access like this, on architectures where read-read reordering is
possible:
I would like to mark this for stable, but the stable rules explicitly say
"no theoretical races", and given that the FD table pointer and
files->count are explicitly stored in the same cacheline, this sort of
reordering seems quite unlikely in practice...
Signed-off-by: Jann Horn <jannh@google.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 66717ad03b80802752c9931afeedfcbd6806a8c2) Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
The clk_disable_unprepare() should be called in the error handling
of devm_clk_bulk_get_optional, fix it by replacing devm_clk_get_optional
and clk_prepare_enable by devm_clk_get_optional_enabled.
Fixes: f5eccd94b63f ("mmc: mediatek: Add subsys clock control for MT8192 msdc") Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20221125090141.3626747-1-cuigaosheng1@huawei.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 5a1122e1a896117485bd58634ca39ed2d4950a66) Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
Allow to add an exit hook to devm managed clocks. Also use
clk_get_optional() in devm_clk_get_optional instead of open coding it.
The generalisation will be used in the next commit to add some more
devm_clk helpers.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Reviewed-by: Alexandru Ardelean <aardelean@deviqon.com> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Link: https://lore.kernel.org/r/20220520075737.758761-3-u.kleine-koenig@pengutronix.de Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Stable-dep-of: c61bfb1cb63d ("mmc: mtk-sd: Fix missing clk_disable_unprepare in msdc_of_clock_parse()") Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit eb94a7a20f3c8dee1eb3a4f47ac21a3ec8229d97) Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
proc_skip_spaces() seems to think it is working on C strings, and ends
up being just a wrapper around skip_spaces() with a really odd calling
convention.
Instead of basing it on skip_spaces(), it should have looked more like
proc_skip_char(), which really is the exact same function (except it
skips a particular character, rather than whitespace). So use that as
inspiration, odd coding and all.
Now the calling convention actually makes sense and works for the
intended purpose.
Reported-and-tested-by: Kyle Zeng <zengyhkyle@gmail.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 48642f94311b0cf9667aa6833f9f5e3a87d2a0ce) Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
proc_get_long() is passed a size_t, but then assigns it to an 'int'
variable for the length. Let's not do that, even if our IO paths are
limited to MAX_RW_COUNT (exactly because of these kinds of type errors).
When __do_semtimedop() goes to sleep because it has to wait for a
semaphore value becoming zero or becoming bigger than some threshold, it
links the on-stack sem_queue to the sem_array, then goes to sleep
without holding a reference on the sem_array.
When __do_semtimedop() comes back out of sleep, one of two things must
happen:
a) We prove that the on-stack sem_queue has been disconnected from the
(possibly freed) sem_array, making it safe to return from the stack
frame that the sem_queue exists in.
b) We stabilize our reference to the sem_array, lock the sem_array, and
detach the sem_queue from the sem_array ourselves.
sem_array has RCU lifetime, so for case (b), the reference can be
stabilized inside an RCU read-side critical section by locklessly
checking whether the sem_queue is still connected to the sem_array.
However, the current code does the lockless check on sem_queue before
starting an RCU read-side critical section, so the result of the
lockless check immediately becomes useless.
Fix it by doing rcu_read_lock() before the lockless check. Now RCU
ensures that if we observe the object being on our queue, the object
can't be freed until rcu_read_unlock().
This bug is only hittable on kernel builds with full preemption support
(either CONFIG_PREEMPT or PREEMPT_DYNAMIC with preempt=full).
Fixes: 370b262c896e ("ipc/sem: avoid idr tree lookup for interrupted semop") Cc: stable@vger.kernel.org Signed-off-by: Jann Horn <jannh@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 4a4073a2e2fe392db08c00c39fdc5e2f8f198547) Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
Currently tpm transactions are executed unconditionally in
tpm_pm_suspend() function, which may lead to races with other tpm
accessors in the system.
Specifically, the hw_random tpm driver makes use of tpm_get_random(),
and this function is called in a loop from a kthread, which means it's
not frozen alongside userspace, and so can race with the work done
during system suspend:
On the subject of suspend, the RISC-V SBI spec states:
This does not cover whether any given events actually reach the hart or
not, just what the hart will do if it receives an event. On PolarFire
SoC, and potentially other SiFive based implementations, events from the
RISC-V timer do reach a hart during suspend. This is not the case for the
implementation on the Allwinner D1 - there timer events are not received
during suspend.
To fix this, the CLOCK_EVT_FEAT_C3STOP (mis)feature was enabled for the
timer driver - but this has broken both RCU stall detection and timers
generally on PolarFire SoC and potentially other SiFive based
implementations.
If an AXI read to the PCIe controller on PolarFire SoC times out, the
system will stall, however, with CLOCK_EVT_FEAT_C3STOP active, the system
just locks up without RCU stalling:
Similarly issues were reported with clock_nanosleep() - with a test app
that sleeps each cpu for 6, 5, 4, 3 ms respectively, HZ=250 & the blamed
commit in place, the sleep times are rounded up to the next jiffy:
Fortunately, the D1 has a second timer, which is "currently used in
preference to the RISC-V/SBI timer driver" so a revert here does not
hurt operation of D1 in its current form.
Ultimately, a DeviceTree property (or node) will be added to encode the
behaviour of the timers, but until then revert the addition of
CLOCK_EVT_FEAT_C3STOP.
In a system with a single initiator node, and one or more memory-only
'target' nodes, the memory-only node(s) would fail to register their
initiator node correctly. i.e. in sysfs:
# ls /sys/devices/system/node/node0/access0/targets/
node0
Where as the correct behavior should be:
# ls /sys/devices/system/node/node0/access0/targets/
node0 node1
This happened because hmat_register_target_initiators() uses list_sort()
to sort the initiator list, but the sort comparision function
(initiator_cmp()) is overloaded to also set the node mask's bits.
In a system with a single initiator, the list is singular, and list_sort
elides the comparision helper call. Thus the node mask never gets set,
and the subsequent search for the best initiator comes up empty.
Add a new helper to consume the sorted initiator list, and generate the
nodemask, decoupling it from the overloaded initiator_cmp() comparision
callback. This prevents the singular list corner case naturally, and
makes the code easier to follow as well.
Cc: <stable@vger.kernel.org> Cc: Rafael J. Wysocki <rafael@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Reported-by: Chris Piper <chris.d.piper@intel.com> Signed-off-by: Vishal Verma <vishal.l.verma@intel.com> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Link: https://lore.kernel.org/r/20221116-acpi_hmat_fix-v2-2-3712569be691@intel.com Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit a759057af7285263093ab10b0bac3e14f35e5fea) Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
In hmat_register_target_initiators(), the variable 'best' gets
initialized in the outer per-locality-type for loop. The initialization
just before setting up 'Access 1' targets was unnecessary. Remove it.
Cc: Rafael J. Wysocki <rafael@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Dan Williams <dan.j.williams@intel.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Vishal Verma <vishal.l.verma@intel.com> Link: https://lore.kernel.org/r/20221116-acpi_hmat_fix-v2-1-3712569be691@intel.com Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Stable-dep-of: 48d4180939e1 ("ACPI: HMAT: Fix initiator registration for single-initiator systems") Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit da8a794d71ec99ee92bde4e174d6a6169c00b381) Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
Recent changes to the DMA code has resulting in the IMX driver failing
I2C transfers when the buffer has been vmalloc. Only perform DMA
transfers if the message has the I2C_M_DMA_SAFE flag set, indicating
the client is providing a buffer which is DMA safe.
This is a minimal fix for stable. The I2C core provides helpers to
allocate a bounce buffer. For a fuller fix the master should make use
of these helpers.
Fixes: 4544b9f25e70 ("dma-mapping: Add vmap checks to dma_map_single()") Signed-off-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 2d16161a2c98730dc56d456e6dd1702a0a9fe735) Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
A problem about i2c-npcm7xx create debugfs failed is triggered with the
following log given:
[ 173.827310] debugfs: Directory 'npcm_i2c' with parent '/' already present!
The reason is that npcm_i2c_init() returns platform_driver_register()
directly without checking its return value, if platform_driver_register()
failed, it returns without destroy the newly created debugfs, resulting
the debugfs of npcm_i2c can never be created later.
The STM32 USART can control RS-485 Transmit Enable in hardware. Since
commit 7df5081cbf5e ("serial: stm32: Add RS485 RTS GPIO control"),
it can alternatively be controlled in software. That was done to allow
RS-485 even if the RTS pin is unavailable because it's pinmuxed to a
different function.
However the commit neglected to deassert Transmit Enable upon invocation
of the ->rs485_config() callback. Fix it.
Avoid forward declarations by moving stm32_usart_tx_empty(),
stm32_usart_rs485_rts_enable() and stm32_usart_rs485_rts_disable()
further up in the driver.
In case the RS485 mode is emulated using GPIO RTS, use the TC interrupt
to deassert the GPIO RTS, otherwise the GPIO RTS stays asserted after a
transmission ended and the RS485 cannot work.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: Erwan Le Ray <erwan.leray@foss.st.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jean Philippe Romain <jean-philippe.romain@foss.st.com> Cc: Valentin Caron <valentin.caron@foss.st.com> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-serial@vger.kernel.org Link: https://lore.kernel.org/r/20220430162845.244655-2-marex@denx.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 45f628f4fd816f4843f6860996fcaa2b461165d1) Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
When the kernel receives a route deletion request from user space it
tries to delete a route that matches the route attributes specified in
the request.
If only prefix information is specified in the request, the kernel
should delete the first matching FIB alias regardless of its associated
FIB info. However, an error is currently returned when the FIB info is
backed by a nexthop object:
# ip nexthop add id 1 via 192.0.2.2 dev dummy10
# ip route add 198.51.100.0/24 nhid 1
# ip route del 198.51.100.0/24
RTNETLINK answers: No such process
Fix by matching on such a FIB info when legacy nexthop attributes are
not specified in the request. An earlier check already covers the case
where a nexthop ID is specified in the request.
Add tests that cover these flows. Before the fix:
# ./fib_nexthops.sh -t ipv4_fcnal
...
TEST: Delete route when not specifying nexthop attributes [FAIL]
Tests passed: 11
Tests failed: 1
After the fix:
# ./fib_nexthops.sh -t ipv4_fcnal
...
TEST: Delete route when not specifying nexthop attributes [ OK ]
Gwangun Jung reported a slab-out-of-bounds access in fib_nh_match:
fib_nh_match+0xf98/0x1130 linux-6.0-rc7/net/ipv4/fib_semantics.c:961
fib_table_delete+0x5f3/0xa40 linux-6.0-rc7/net/ipv4/fib_trie.c:1753
inet_rtm_delroute+0x2b3/0x380 linux-6.0-rc7/net/ipv4/fib_frontend.c:874
Separate nexthop objects are mutually exclusive with the legacy
multipath spec. Fix fib_nh_match to return if the config for the
to be deleted route contains a multipath spec while the fib_info
is using a nexthop object.
Fixes: 493ced1ac47c ("ipv4: Allow routes to use nexthop objects") Fixes: 6bf92d70e690 ("net: ipv4: fix route with nexthop object delete warning") Reported-by: Gwangun Jung <exsociety@gmail.com> Signed-off-by: David Ahern <dsahern@kernel.org> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Tested-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: d5082d386eee ("ipv4: Fix route deletion when nexthop info is not specified") Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 25174d91e4a32a24204060d283bd5fa6d0ddf133) Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
I made a stupid typo when adding the nexthop route warning selftest and
added both $IP and ip after it (double ip) on the cleanup path. The
error doesn't show up when running the test, but obviously it doesn't
cleanup properly after it.
Fixes: 392baa339c6a ("selftests: net: add delete nexthop route warning test") Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: d5082d386eee ("ipv4: Fix route deletion when nexthop info is not specified") Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit a0ad247e55ea5a9dd40115a152bf4fde24a81bab) Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
Add a test which causes a WARNING on kernels which treat a
nexthop route like a normal route when comparing for deletion and a
device is specified. That is, a route is found but we hit a warning while
matching it. The warning is from fib_info_nh() in include/net/nexthop.h
because we run it on a fib_info with nexthop object. The call chain is:
inet_rtm_delroute -> fib_table_delete -> fib_nh_match (called with a
nexthop fib_info and also with fc_oif set thus calling fib_info_nh on
the fib_info and triggering the warning).
Repro steps:
$ ip nexthop add id 12 via 172.16.1.3 dev veth1
$ ip route add 172.16.101.1/32 nhid 12
$ ip route delete 172.16.101.1/32 dev veth1
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: d5082d386eee ("ipv4: Fix route deletion when nexthop info is not specified") Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 532847b69c29943460aa928ce7267c63501a94e1) Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
When enabled, KASAN enlarges function's stack-frames. Pushing quite a few
over the current threshold. This can mainly be seen on 32-bit
architectures where the present limit (when !GCC) is a lowly 1024-Bytes.
Link: https://lkml.kernel.org/r/20221125120750.3537134-3-lee@kernel.org Signed-off-by: Lee Jones <lee@kernel.org> Acked-by: Arnd Bergmann <arnd@arndb.de> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: "Christian König" <christian.koenig@amd.com> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: David Airlie <airlied@gmail.com> Cc: Harry Wentland <harry.wentland@amd.com> Cc: Leo Li <sunpeng.li@amd.com> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Maxime Ripard <mripard@kernel.org> Cc: Nathan Chancellor <nathan@kernel.org> Cc: Nick Desaulniers <ndesaulniers@google.com> Cc: "Pan, Xinhui" <Xinhui.Pan@amd.com> Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Cc: Thomas Zimmermann <tzimmermann@suse.de> Cc: Tom Rix <trix@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit e0783558817d7fcac060c0602afe5764e3392f93) Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
PA-RISC uses a much bigger frame size for functions than other
architectures. So increase it to 2048 for 32- and 64-bit kernels.
This fixes e.g. a warning in lib/xxhash.c.
Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Helge Deller <deller@gmx.de>
Stable-dep-of: 152fe65f300e ("Kconfig.debug: provide a little extra FRAME_WARN leeway when KASAN is enabled") Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 723fa02e0e0ad2398e2a6c0e6b2087c9dacf4212) Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
The issue is reported when removing memory through virtio_mem device. The
transparent huge page, experienced copy-on-write fault, is wrongly
regarded as pinned. The transparent huge page is escaped from being
isolated in isolate_migratepages_block(). The transparent huge page can't
be migrated and the corresponding memory block can't be put into offline
state.
Fix it by replacing page_mapcount() with total_mapcount(). With this, the
transparent huge page can be isolated and migrated, and the memory block
can be put into offline state. Besides, The page's refcount is increased
a bit earlier to avoid the page is released when the check is executed.
Link: https://lkml.kernel.org/r/20221124095523.31061-1-gshan@redhat.com Fixes: 1da2f328fa64 ("mm,thp,compaction,cma: allow THP migration for CMA allocations") Signed-off-by: Gavin Shan <gshan@redhat.com> Reported-by: Zhenyu Zhang <zhenyzha@redhat.com> Tested-by: Zhenyu Zhang <zhenyzha@redhat.com> Suggested-by: David Hildenbrand <david@redhat.com> Acked-by: David Hildenbrand <david@redhat.com> Cc: Alistair Popple <apopple@nvidia.com> Cc: Hugh Dickins <hughd@google.com> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: William Kucharski <william.kucharski@oracle.com> Cc: Zi Yan <ziy@nvidia.com> Cc: <stable@vger.kernel.org> [5.7+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit b951ab4b35ba15018abfb6ebe7e53c28adaf786f) Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
__isolate_lru_page_prepare() conflates two unrelated functions, with the
flags to one disjoint from the flags to the other; and hides some of the
important checks outside of isolate_migratepages_block(), where the
sequence is better to be visible. It comes from the days of lumpy
reclaim, before compaction, when the combination made more sense.
Move what's needed by mm/compaction.c isolate_migratepages_block() inline
there, and what's needed by mm/vmscan.c isolate_lru_pages() inline there.
Shorten "isolate_mode" to "mode", so the sequence of conditions is easier
to read. Declare a "mapping" variable, to save one call to page_mapping()
(but not another: calling again after page is locked is necessary).
Simplify isolate_lru_pages() with a "move_to" list pointer.
Link: https://lkml.kernel.org/r/879d62a8-91cc-d3c6-fb3b-69768236df68@google.com Signed-off-by: Hugh Dickins <hughd@google.com> Acked-by: David Rientjes <rientjes@google.com> Reviewed-by: Alex Shi <alexs@kernel.org> Cc: Alexander Duyck <alexander.duyck@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stable-dep-of: 829ae0f81ce0 ("mm: migrate: fix THP's mapcount on isolation") Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit c5eda6029cf9099120d2d788c73490ac813549cc) Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
for_each_pci_dev() is implemented by pci_get_device(). The comment of
pci_get_device() says that it will increase the reference count for the
returned pci_dev and also decrease the reference count for the input
pci_dev @from if it is not NULL.
If we break for_each_pci_dev() loop with pdev not NULL, we need to call
pci_dev_put() to decrease the reference count. Add the missing
pci_dev_put() for the error path to avoid reference count leak.
Fixes: 2e4552893038 ("iommu/vt-d: Unify the way to process DMAR device scope array") Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com> Link: https://lore.kernel.org/r/20221121113649.190393-3-wangxiongfeng2@huawei.com Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit bdb613ef179ad4bb9d56a2533e9b30e434f1dfb7) Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
for_each_pci_dev() is implemented by pci_get_device(). The comment of
pci_get_device() says that it will increase the reference count for the
returned pci_dev and also decrease the reference count for the input
pci_dev @from if it is not NULL.
If we break for_each_pci_dev() loop with pdev not NULL, we need to call
pci_dev_put() to decrease the reference count. Add the missing
pci_dev_put() before 'return true' to avoid reference count leak.
Fixes: 89a6079df791 ("iommu/vt-d: Force IOMMU on for platform opt in hint") Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com> Link: https://lore.kernel.org/r/20221121113649.190393-2-wangxiongfeng2@huawei.com Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit b6eea8b2e858a20ad58ac62dc2de90fea2413f94) Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
Walking the nvme_ns_head siblings list is protected by the head's srcu
in nvme_ns_head_submit_bio() but not nvme_mpath_revalidate_paths().
Removing namespaces from the list also fails to synchronize the srcu.
Concurrent scan work can therefore cause use-after-frees.
Hold the head's srcu lock in nvme_mpath_revalidate_paths() and
synchronize with the srcu, not the global RCU, in nvme_ns_remove().
Observed the following panic when making NVMe/RDMA connections
with native multipath on the Rocky Linux 8.6 kernel
(it seems the upstream kernel has the same race condition).
Disassembly shows the faulting instruction is cmp 0x50(%rdx),%rcx;
computing capacity != get_capacity(ns->disk).
Address 0x50 is dereferenced because ns->disk is NULL.
The NULL disk appears to be the result of concurrent scan work
freeing the namespace (note the log line in the middle of the panic).
If a crash happens on cpu3 and all interrupts are binding on cpu0, the
bad irq routing will cause a crash kernel which can't receive any irq.
Because crash kernel won't clean up all harts' PLIC enable bits in
enable registers. This patch is similar to 9141a003a491 ("ARM: 7316/1:
kexec: EOI active and mask all interrupts in kexec crash path") and 78fd584cdec0 ("arm64: kdump: implement machine_crash_shutdown()"), and
PowerPC also has the same mechanism.
Currently, when detecting vmap stack overflow, riscv firstly switches
to the so called shadow stack, then use this shadow stack to call the
get_overflow_stack() to get the overflow stack. However, there's
a race here if two or more harts use the same shadow stack at the same
time.
To solve this race, we introduce spin_shadow_stack atomic var, which
will be swap between its own address and 0 in atomic way, when the
var is set, it means the shadow_stack is being used; when the var
is cleared, it means the shadow_stack isn't being used.
Fixes: 31da94c25aea ("riscv: add VMAP_STACK overflow detection") Signed-off-by: Jisheng Zhang <jszhang@kernel.org> Suggested-by: Guo Ren <guoren@kernel.org> Reviewed-by: Guo Ren <guoren@kernel.org> Link: https://lore.kernel.org/r/20221030124517.2370-1-jszhang@kernel.org
[Palmer: Add AQ to the swap, and also some comments.] Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit ac00301adb19df54f2eae1efc4bad7447c0156ce) Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
The EFI page table is initially created as a copy of the kernel page table.
With VMAP_STACK enabled, kernel stacks are allocated in the vmalloc area:
if the stack is allocated in a new PGD (one that was not present at the
moment of the efi page table creation or not synced in a previous vmalloc
fault), the kernel will take a trap when switching to the efi page table
when the vmalloc kernel stack is accessed, resulting in a kernel panic.
Fix that by updating the efi kernel mappings before switching to the efi
page table.
There is a possibility of dividing by zero due to the pcs->bits_per_pin
if pcs->fmask() also has a value of zero and called fls
from asm-generic/bitops/builtin-fls.h or arch/x86/include/asm/bitops.h.
The function pcs_probe() has the branch that assigned to fmask 0 before
pcs_allocate_pin_table() was called
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 4e7e8017a80e ("pinctrl: pinctrl-single: enhance to configure multiple pins of different modules") Signed-off-by: Maxim Korotkov <korotkov.maxim.s@gmail.com> Reviewed-by: Tony Lindgren <tony@atomide.com> Link: https://lore.kernel.org/r/20221117123034.27383-1-korotkov.maxim.s@gmail.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit d86d698925456f88f44183c70ce1b46656a28fed) Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
For _sx controls the semantics of the max field is not the usual one, max
is the number of steps rather than the maximum value. This means that our
check in snd_soc_put_volsw_sx() needs to just check against the maximum
value.
Fixes: 4f1e50d6a9cf9c1b ("ASoC: ops: Reject out of bounds values in snd_soc_put_volsw_sx()") Signed-off-by: Mark Brown <broonie@kernel.org> Link: https://lore.kernel.org/r/20220511134137.169575-1-broonie@kernel.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 98b15c706644bebc19d2e77ccc360cc51444f6d0) Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
make_mmu_pages_available() must be called with mmu_lock held for write.
However, if the TDP MMU is used, it will be called with mmu_lock held for
read.
This function does nothing unless shadow pages are used, so there is no
race unless nested TDP is used.
Since nested TDP uses shadow pages, old shadow pages may be zapped by this
function even when the TDP MMU is enabled.
Since shadow pages are never allocated by kvm_tdp_mmu_map(), a race
condition can be avoided by not calling make_mmu_pages_available() if the
TDP MMU is currently in use.
I encountered this when repeatedly starting and stopping nested VM.
It can be artificially caused by allocating a large number of nested TDP
SPTEs.
For example, the following BUG and general protection fault are caused in
the host kernel.
The root cause for this is a tiny overlooking in
io_poll_check_events() when cocurrently run with poll cancel routine
io_poll_cancel_req().
The interleaving to trigger use-after-free:
CPU0 | CPU1
|
io_apoll_task_func() | io_poll_cancel_req()
io_poll_check_events() |
// do while first loop |
v = atomic_read(...) |
// v = poll_refs = 1 |
... | io_poll_mark_cancelled()
| atomic_or()
| // poll_refs =
IO_POLL_CANCEL_FLAG | 1
|
atomic_sub_return(...) |
// poll_refs = IO_POLL_CANCEL_FLAG |
// loop continue |
|
| io_poll_execute()
| io_poll_get_ownership()
| // poll_refs =
IO_POLL_CANCEL_FLAG | 1
| // gets the ownership
v = atomic_read(...) |
// poll_refs not change |
|
if (v & IO_POLL_CANCEL_FLAG) |
return -ECANCELED; |
// io_poll_check_events return |
// will go into |
// io_req_complete_failed() free req |
|
| io_apoll_task_func()
| // also go into
io_req_complete_failed()
And the interleaving to trigger the kernel WARNING:
CPU0 | CPU1
|
io_apoll_task_func() | io_poll_cancel_req()
io_poll_check_events() |
// do while first loop |
v = atomic_read(...) |
// v = poll_refs = 1 |
... | io_poll_mark_cancelled()
| atomic_or()
| // poll_refs =
IO_POLL_CANCEL_FLAG | 1
|
atomic_sub_return(...) |
// poll_refs = IO_POLL_CANCEL_FLAG |
// loop continue |
|
v = atomic_read(...) |
// v = IO_POLL_CANCEL_FLAG |
| io_poll_execute()
| io_poll_get_ownership()
| // poll_refs =
IO_POLL_CANCEL_FLAG | 1
| // gets the ownership
|
WARN_ON_ONCE(!(v & IO_POLL_REF_MASK))) |
// v & IO_POLL_REF_MASK = 0 WARN |
|
| io_apoll_task_func()
| // also go into
io_req_complete_failed()
By looking up the source code and communicating with Pavel, the
implementation of this atomic poll refs should continue the loop of
io_poll_check_events() just to avoid somewhere else to grab the
ownership. Therefore, this patch simply adds another AND operation to
make sure the loop will stop if it finds the poll_refs is exactly equal
to IO_POLL_CANCEL_FLAG. Since io_poll_cancel_req() grabs ownership and
will finally make its way to io_req_complete_failed(), the req will
be reclaimed as expected.
Fixes: aa43477b0402 ("io_uring: poll rework") Signed-off-by: Lin Ma <linma@zju.edu.cn> Reviewed-by: Pavel Begunkov <asml.silence@gmail.com>
[axboe: tweak description and code style] Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Pavel Begunkov <asml.silence@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit df4b177b48516da64b988722a22d93d257dcda9a) Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
poll_refs carry two functions, the first is ownership over the request.
The second is notifying the io_poll_check_events() that there was an
event but wake up couldn't grab the ownership, so io_poll_check_events()
should retry.
We want to make poll_refs more robust against overflows. Instead of
always incrementing it, which covers two purposes with one atomic, check
if poll_refs is elevated enough and if so set a retry flag without
attempts to grab ownership. The gap between the bias check and following
atomics may seem racy, but we don't need it to be strict. Moreover there
might only be maximum 4 parallel updates: by the first and the second
poll entries, __io_arm_poll_handler() and cancellation. From those four,
only poll wake ups may be executed multiple times, but they're protected
by a spin.
Replace atomically substracting the ownership reference at the end of
arming a poll with a cmpxchg. We try to release ownership by setting 0
assuming that poll_refs didn't change while we were arming. If it did
change, we keep the ownership and use it to queue a tw, which is fully
capable to process all events and (even tolerates spurious wake ups).
It's a bit more elegant as we reduce races b/w setting the cancellation
flag and getting refs with this release, and with that we don't have to
worry about any kinds of underflows. It's not the fastest path for
polling. The performance difference b/w cmpxchg and atomic dec is
usually negligible and it's not the fastest path.
We may never try to process a poll wake and its mask if there was
multiple wake ups racing for queueing up a tw. Force
io_poll_check_events() to update the mask by vfs_poll().
When io_poll_check_events() collides with someone attempting to queue a
task work, it'll spin for one more time. However, it'll continue to use
the mask from the first iteration instead of updating it. For example,
if the first wake up was a EPOLLIN and the second EPOLLOUT, the
userspace will not get EPOLLOUT in time.
Clear the mask for all subsequent iterations to force vfs_poll().
After 65536 dynamic events have been added and removed, the "type" field
of the event then uses the first type number that is available (not
currently used by other events). A type number is the identifier of the
binary blobs in the tracing ring buffer (known as events) to map them to
logic that can parse the binary blob.
The issue is that if a dynamic event (like a kprobe event) is traced and
is in the ring buffer, and then that event is removed (because it is
dynamic, which means it can be created and destroyed), if another dynamic
event is created that has the same number that new event's logic on
parsing the binary blob will be used.
To show how this can be an issue, the following can crash the kernel:
# cd /sys/kernel/tracing
# for i in `seq 65536`; do
echo 'p:kprobes/foo do_sys_openat2 $arg1:u32' > kprobe_events
# done
For every iteration of the above, the writing to the kprobe_events will
remove the old event and create a new one (with the same format) and
increase the type number to the next available on until the type number
reaches over 65535 which is the max number for the 16 bit type. After it
reaches that number, the logic to allocate a new number simply looks for
the next available number. When an dynamic event is removed, that number
is then available to be reused by the next dynamic event created. That is,
once the above reaches the max number, the number assigned to the event in
that loop will remain the same.
Now that means deleting one dynamic event and created another will reuse
the previous events type number. This is where bad things can happen.
After the above loop finishes, the kprobes/foo event which reads the
do_sys_openat2 function call's first parameter as an integer.
==================================================================
BUG: KASAN: use-after-free in string+0xd4/0x1c0
Read of size 1 at addr ffff88805fdbbfa0 by task cat/2049
This was found when Zheng Yejian sent a patch to convert the event type
number assignment to use IDA, which gives the next available number, and
this bug showed up in the fuzz testing by Yujie Liu and the kernel test
robot. But after further analysis, I found that this behavior is the same
as when the event type numbers go past the 16bit max (and the above shows
that).
As modules have a similar issue, but is dealt with by setting a
"WAS_ENABLED" flag when a module event is enabled, and when the module is
freed, if any of its events were enabled, the ring buffer that holds that
event is also cleared, to prevent reading stale events. The same can be
done for dynamic events.
If any dynamic event that is being removed was enabled, then make sure the
buffers they were enabled in are now cleared.
Link: https://lkml.kernel.org/r/20221123171434.545706e3@gandalf.local.home Link: https://lore.kernel.org/all/20221110020319.1259291-1-zhengyejian1@huawei.com/ Cc: stable@vger.kernel.org Cc: Andrew Morton <akpm@linux-foundation.org>
Depends-on: e18eb8783ec49 ("tracing: Add tracing_reset_all_online_cpus_unlocked() function")
Depends-on: 5448d44c38557 ("tracing: Add unified dynamic event framework")
Depends-on: 6212dd29683ee ("tracing/kprobes: Use dyn_event framework for kprobe events")
Depends-on: 065e63f951432 ("tracing: Only have rmmod clear buffers that its events were active in")
Depends-on: 575380da8b469 ("tracing: Only clear trace buffer on module unload if event was traced") Fixes: 77b44d1b7c283 ("tracing/kprobes: Rename Kprobe-tracer to kprobe-event") Reported-by: Zheng Yejian <zhengyejian1@huawei.com> Reported-by: Yujie Liu <yujie.liu@intel.com> Reported-by: kernel test robot <yujie.liu@intel.com> Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 417d5ea6e735e5d88ffb6c436cf2938f3f476dd1) Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
commit 94eedf3dded5 ("tracing: Fix race where eprobes can be called before
the event") fixed an issue where if an event is soft disabled, and the
trigger is being added, there's a small window where the event sees that
there's a trigger but does not see that it requires reading the event yet,
and then calls the trigger with the record == NULL.
This could be solved with adding memory barriers in the hot path, or to
make sure that all the triggers requiring a record check for NULL. The
latter was chosen.
Commit 94eedf3dded5 set the eprobe trigger handle to check for NULL, but
the same needs to be done with histograms.
Users of intel_gt_retire_requests_timeout() expect 0 return value on
success. However, we have no protection from passing back 0 potentially
returned by a call to dma_fence_wait_timeout() when it succedes right
after its timeout has expired.
Replace 0 with -ETIME before potentially using the timeout value as return
code, so -ETIME is returned if there are still some requests not retired
after timeout, 0 otherwise.
v3: Use conditional expression, more compact but also better reflecting
intention standing behind the change.
v2: Move the added lines down so flush_submission() is not affected.
Commit b97060a99b01 ("drm/i915/guc: Update intel_gt_wait_for_idle to work
with GuC") extended the API of intel_gt_retire_requests_timeout() with an
extra argument 'remaining_timeout', intended for passing back unconsumed
portion of requested timeout when 0 (success) is returned. However, when
request retirement happens to succeed despite an error returned by a call
to dma_fence_wait_timeout(), that error code (a negative value) is passed
back instead of remaining time. If we then pass that negative value
forward as requested timeout to intel_uc_wait_for_idle(), an explicit BUG
will be triggered.
If request retirement succeeds but an error code is passed back via
remaininig_timeout, we may have no clue on how much of the initial timeout
might have been left for spending it on waiting for GuC to become idle.
OTOH, since all pending requests have been successfully retired, that
error code has been already ignored by intel_gt_retire_requests_timeout(),
then we shouldn't fail.
Assume no more time has been left on error and pass 0 timeout value to
intel_uc_wait_for_idle() to give it a chance to return success if GuC is
already idle.
v3: Don't fail on any error passed back via remaining_timeout.
v2: Fix the issue on the caller side, not the provider.
Fixes: 0c2c02b66c672e ("drm/amdgpu/vcn: add firmware support for dimgrey_cavefish") Signed-off-by: Leo Liu <leo.liu@amd.com> Reviewed-by: James Zhu <James.Zhu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit ff1591ba33b8b83977e46a340f2d9b22099766d2) Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
Patch series "Fix a bunch of allmodconfig errors", v2.
Since b339ec9c229aa ("kbuild: Only default to -Werror if COMPILE_TEST")
WERROR now defaults to COMPILE_TEST meaning that it's enabled for
allmodconfig builds. This leads to some interesting build failures when
using Clang, each resolved in this set.
With this set applied, I am able to obtain a successful allmodconfig Arm
build.
This patch (of 2):
calculate_bandwidth() is presently broken on all !(X86_64 || SPARC64 ||
ARM64) architectures built with Clang (all released versions), whereby the
stack frame gets blown up to well over 5k. This would cause an immediate
kernel panic on most architectures. We'll revert this when the following
bug report has been resolved:
https://github.com/llvm/llvm-project/issues/41896.
Link: https://lkml.kernel.org/r/20221125120750.3537134-1-lee@kernel.org Link: https://lkml.kernel.org/r/20221125120750.3537134-2-lee@kernel.org Signed-off-by: Lee Jones <lee@kernel.org> Suggested-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Arnd Bergmann <arnd@arndb.de> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: "Christian König" <christian.koenig@amd.com> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: David Airlie <airlied@gmail.com> Cc: Harry Wentland <harry.wentland@amd.com> Cc: Lee Jones <lee@kernel.org> Cc: Leo Li <sunpeng.li@amd.com> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Maxime Ripard <mripard@kernel.org> Cc: Nathan Chancellor <nathan@kernel.org> Cc: Nick Desaulniers <ndesaulniers@google.com> Cc: "Pan, Xinhui" <Xinhui.Pan@amd.com> Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Cc: Thomas Zimmermann <tzimmermann@suse.de> Cc: Tom Rix <trix@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit ac2d7fa9084892c2c1232016ecdeadf4b354212f) Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
Commit 20b92a30b561 ("mmc: sdhci: update signal voltage switch code")
removed voltage switch delays from sdhci because mmc core had been
enhanced to support them. However that assumed that sdhci_set_ios()
did a single clock change, which it did not, and so the delays in mmc
core, which should have come after the first clock change, were not
effective.
Fix by avoiding re-configuring UHS and preset settings when the clock
is turning on and the settings have not changed. That then also avoids
the associated clock changes, so that then sdhci_set_ios() does a single
clock change when voltage switching, and the mmc core delays become
effective.
To do that has meant keeping track of driver strength (host->drv_type),
and cases of reinitialization (host->reinit_uhs).
Note also, the 'turning_on_clk' restriction should not be necessary
but is done to minimize the impact of the change on stable kernels.
Fixes: 20b92a30b561 ("mmc: sdhci: update signal voltage switch code") Cc: stable@vger.kernel.org Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20221128133259.38305-2-adrian.hunter@intel.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 57ee7bc4c60a630f771d387e7fa4a7856b972bd2) Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
With the current logic the "failed to exit halt state" error would be
shown even if any other bit than CQHCI_HALT was set in the CQHCI_CTL
register, since the right hand side is always true. Fix this by using
the correct operator (bit-wise instead of logical AND) to only check for
the halt bit flag, which was obviously intended here.
Fixes: 85236d2be844 ("mmc: sdhci-esdhc-imx: clear the HALT bit when enable CQE") Signed-off-by: Sebastian Falbesoner <sebastian.falbesoner@gmail.com> Acked-by: Haibo Chen <haibo.chen@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20221121105721.1903878-1-sebastian.falbesoner@gmail.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 4c7681c1a52fb6cb5b370635d27df7f610f554e7) Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
Clean up the MMC_TRIM_ARGS define that became ambiguous with DISCARD
introduction. While at it, let's fix one usage where MMC_TRIM_ARGS falsely
included DISCARD too.
Fixes: b3bf915308ca ("mmc: core: new discard feature support at eMMC v4.5") Signed-off-by: Christian Loehle <cloehle@hyperstone.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/11376b5714964345908f3990f17e0701@hyperstone.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 01dbe4db590a8a7e4698f83e2d3cf5cc618e7bb3) Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
In __mmc_test_register_dbgfs_file(), we need to assign 'file', as it's
being used when removing the debugfs files when the mmc_test module is
removed.
Fixes: a04c50aaa916 ("mmc: core: no need to check return value of debugfs_create functions") Signed-off-by: Ye Bin <yebin10@huawei.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org
[Ulf: Re-wrote the commit msg] Link: https://lore.kernel.org/r/20221123095506.1965691-1-yebin@huaweicloud.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 738946e35504f66dfda1978ec72d0253a434ffc0) Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
Currently, pause frame register GMAC_RX_FLOW_CTRL_RFE is not updated
correctly when 'ethtool -A <IFACE> autoneg off rx off tx off' command
is issued. This fix ensures the flow control change is reflected directly
in the GMAC_RX_FLOW_CTRL_RFE register.
Fixes: 46f69ded988d ("net: stmmac: Use resolved link config in mac_link_up()") Cc: <stable@vger.kernel.org> # 5.10.x Signed-off-by: Goh, Wei Sheng <wei.sheng.goh@intel.com> Signed-off-by: Noor Azura Ahmad Tarmizi <noor.azura.ahmad.tarmizi@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 635d0517348e0d437158ddfac913354f0fe1819f) Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
The V4L2_MEMORY_USERPTR interface is long deprecated and shouldn't be
used (and is discouraged for any modern v4l drivers). And Seth Jenkins
points out that the fallback to VM_PFNMAP/VM_IO is fundamentally racy
and dangerous.
Note that it's not even a case that should trigger, since any normal
user pointer logic ends up just using the pin_user_pages_fast() call
that does the proper page reference counting. That's not the problem
case, only if you try to use special device mappings do you have any
issues.
Normally I'd just remove this during the merge window, but since Seth
pointed out the problem cases, we really want to know as soon as
possible if there are actually any users of this odd special case of a
legacy interface. Neither Hans nor Mauro seem to think that such
mis-uses of the old legacy interface should exist. As Mauro says:
"See, V4L2 has actually 4 streaming APIs:
- Kernel-allocated mmap (usually referred simply as just mmap);
- USERPTR mmap;
- read();
- dmabuf;
The USERPTR is one of the oldest way to use it, coming from V4L
version 1 times, and by far the least used one"
And Hans chimed in on the USERPTR interface:
"To be honest, I wouldn't mind if it goes away completely, but that's a
bit of a pipe dream right now"
but while removing this legacy interface entirely may be a pipe dream we
can at least try to remove the unlikely (and actively broken) case of
using special device mappings for USERPTR accesses.
This replaces it with a WARN_ONCE() that we can remove once we've
hopefully confirmed that no actual users exist.
NOTE! Longer term, this means that a 'struct frame_vector' only ever
contains proper page pointers, and all the games we have with converting
them to pages can go away (grep for 'frame_vector_to_pages()' and the
uses of 'vec->is_pfns'). But this is just the first step, to verify
that this code really is all dead, and do so as quickly as possible.
Reported-by: Seth Jenkins <sethjenkins@google.com> Acked-by: Hans Verkuil <hverkuil@xs4all.nl> Acked-by: Mauro Carvalho Chehab <mchehab@kernel.org> Cc: David Hildenbrand <david@redhat.com> Cc: Jan Kara <jack@suse.cz> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 9132dcdf3bf602609f5947deac44692054245f5f) Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
The firmware on some systems may configure GPIO pins to be
an interrupt source in so called "direct IRQ" mode. In such
cases the GPIO controller driver has no idea if those pins
are being used or not. At the same time, there is a known bug
in the firmwares that don't restore the pin settings correctly
after suspend, i.e. by an unknown reason the Rx value becomes
inverted.
Hence, let's save and restore the pins that are configured
as GPIOs in the input mode with GPIROUTIOXAPIC bit set.
The "force" argument to write_spec_ctrl_current() is currently ambiguous
as it does not guarantee the MSR write. This is due to the optimization
that writes to the MSR happen only when the new value differs from the
cached value.
This is fine in most cases, but breaks for S3 resume when the cached MSR
value gets out of sync with the hardware MSR value due to S3 resetting
it.
When x86_spec_ctrl_current is same as x86_spec_ctrl_base, the MSR write
is skipped. Which results in SPEC_CTRL mitigations not getting restored.
Move the MSR write from write_spec_ctrl_current() to a new function that
unconditionally writes to the MSR. Update the callers accordingly and
rename functions.
If DAT metadata file is corrupted on disk, there is a case where
req->pr_desc_bh is NULL and blocknr is 0 at nilfs_dat_commit_end() during
a b-tree operation that cascadingly updates ancestor nodes of the b-tree,
because nilfs_dat_commit_alloc() for a lower level block can initialize
the blocknr on the same DAT entry between nilfs_dat_prepare_end() and
nilfs_dat_commit_end().
If this happens, nilfs_dat_commit_end() calls nilfs_dat_commit_free()
without valid buffer heads in req->pr_desc_bh and req->pr_bitmap_bh, and
causes the NULL pointer dereference above in
nilfs_palloc_commit_free_entry() function, which leads to a crash.
Fix this by adding a NULL check on req->pr_desc_bh and req->pr_bitmap_bh
before nilfs_palloc_commit_free_entry() in nilfs_dat_commit_free().
This also calls nilfs_error() in that case to notify that there is a fatal
flaw in the filesystem metadata and prevent further operations.
The latest version of grep claims the egrep is now obsolete so the build
now contains warnings that look like:
egrep: warning: egrep is obsolescent; using grep -E
fix this up by moving the related file to use "grep -E" instead.
sed -i "s/egrep/grep -E/g" `grep egrep -rwl tools/vm`
Here are the steps to install the latest grep:
wget http://ftp.gnu.org/gnu/grep/grep-3.8.tar.gz
tar xf grep-3.8.tar.gz
cd grep-3.8 && ./configure && make
sudo make install
export PATH=/usr/local/bin:$PATH
Link: https://lkml.kernel.org/r/1668825419-30584-1-git-send-email-yangtiezhu@loongson.cn Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn> Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 2e44dd9a8dd66910a917953d0a062d05eb10151f) Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
The config to be able to inject error codes into any function annotated
with ALLOW_ERROR_INJECTION() is enabled when FUNCTION_ERROR_INJECTION is
enabled. But unfortunately, this is always enabled on x86 when KPROBES
is enabled, and there's no way to turn it off.
As kprobes is useful for observability of the kernel, it is useful to
have it enabled in production environments. But error injection should
be avoided. Add a prompt to the config to allow it to be disabled even
when kprobes is enabled, and get rid of the "def_bool y".
This is a kernel debug feature (it's in Kconfig.debug), and should have
never been something enabled by default.
Cc: stable@vger.kernel.org Fixes: 540adea3809f6 ("error-injection: Separate error-injection from kprobe") Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit b60a8ad771fd15a1539fe6488bc424bd7dabce2a) Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
For Lexicon I-ONIX FW810S, the call of ioctl(2) with
SNDRV_PCM_IOCTL_HW_PARAMS can returns -ETIMEDOUT. This is a regression due
to the commit 41319eb56e19 ("ALSA: dice: wait just for
NOTIFY_CLOCK_ACCEPTED after GLOBAL_CLOCK_SELECT operation"). The device
does not emit NOTIFY_CLOCK_ACCEPTED notification when accepting
GLOBAL_CLOCK_SELECT operation with the same parameters as current ones.
This commit fixes the regression. When receiving no notification, return
-ETIMEDOUT as long as operating for any change.
Fixes: 41319eb56e19 ("ALSA: dice: wait just for NOTIFY_CLOCK_ACCEPTED after GLOBAL_CLOCK_SELECT operation") Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Link: https://lore.kernel.org/r/20221130130604.29774-1-o-takashi@sakamocchi.jp Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 757eb00c4c4063749649ef992cd989bc9043656d) Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
64-bit RISC-V kernels have the kernel image mapped separately to alias
the linear map. The linear map and the kernel image map are documented
as "direct mapping" and "kernel" respectively in [1].
At image load time, the linear map corresponding to the kernel image
is set to PAGE_READ permission, and the kernel image map is set to
PAGE_READ|PAGE_EXEC.
When the initmem is freed, the pages in the linear map should be
restored to PAGE_READ|PAGE_WRITE, whereas the corresponding pages in
the kernel image map should be restored to PAGE_READ, by removing the
PAGE_EXEC permission.
This is not the case. For 64-bit kernels, only the linear map is
restored to its proper page permissions at initmem free, and not the
kernel image map.
In practise this results in that the kernel can potentially jump to
dead __init code, and start executing invalid instructions, without
getting an exception.
Restore the freed initmem properly, by setting both the kernel image
map to the correct permissions.
[1] Documentation/riscv/vm-layout.rst
Fixes: e5c35fa04019 ("riscv: Map the kernel with correct permissions the first time") Signed-off-by: Björn Töpel <bjorn@rivosinc.com> Reviewed-by: Alexandre Ghiti <alex@ghiti.fr> Tested-by: Alexandre Ghiti <alex@ghiti.fr> Link: https://lore.kernel.org/r/20221115090641.258476-1-bjorn@kernel.org Cc: stable@vger.kernel.org Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit a1a96a6f302cad356e905ee7b87dbbb353975529) Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
lkp reported a build error, I tried the config and can reproduce
build error as below:
VDSOLD arch/riscv/kernel/vdso/vdso.so.dbg
ld.lld: error: section .note file range overlaps with .text
>>> .note range is [0x7C8, 0x803]
>>> .text range is [0x800, 0x1993]
ld.lld: error: section .text file range overlaps with .dynamic
>>> .text range is [0x800, 0x1993]
>>> .dynamic range is [0x808, 0x937]
ld.lld: error: section .note virtual address range overlaps with .text
>>> .note range is [0x7C8, 0x803]
>>> .text range is [0x800, 0x1993]
Fix it by setting DISABLE_BRANCH_PROFILING which will disable branch
tracing for vdso, thus avoid useless _ftrace_annotated_branch section
and _ftrace_branch section. Although we can also fix it by removing
the hardcoded .text begin address, but I think that's another story
and should be put into another patch.
As comment of pci_get_domain_bus_and_slot() says, it returns
a pci device with refcount increment, when finish using it,
the caller must decrement the reference count by calling
pci_dev_put(). So call it after using to avoid refcount leak.
If coretemp_add_core() gets an error then pdata->core_data[indx]
is already NULL and has been kfreed. Don't pass that to
sysfs_remove_group() as that will crash in sysfs_remove_group().
After system resumed on some environment board, the promiscuous mode
is disabled because the SoC turned off. So, call ravb_set_rx_mode() in
the ravb_resume() to fix the issue.
projects / mirror_ubuntu-jammy-kernel.git / log