Jon Hunter [Wed, 21 Aug 2019 15:02:40 +0000 (16:02 +0100)]
clocksource/drivers/timer-of: Do not warn on deferred probe
Deferred probe is an expected return value for clk_get() on many
platforms. The driver deals with it properly, so there's no need
to output a warning that may potentially confuse users.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Avi Fishman [Mon, 29 Jul 2019 17:03:54 +0000 (20:03 +0300)]
clocksource/drivers/npcm: Fix GENMASK and timer operation
NPCM7XX_Tx_OPER GENMASK bits are wrong, fix them.
Hopefully the NPCM7XX_REG_TICR0 register reset value of those bits was 0,
so it did not cause an issue.
The function npcm7xx_timer_oneshot() reads the register
NPCM7XX_REG_TCSR0, modifies it and then reads it again overwriting the
previous changes. Remove the extra read which is pointless.
The function npcm7xx_timer_periodic() is correct but the code writes
to the NPCM7XX_REG_TICR0 register while it is dealing with the
NPCM7XX_REG_TCSR0 register, that is confusing. Separate the write to
the registers in the code for the sake of clarity.
Fixes: 1c00289ecd12 ("clocksource/drivers/npcm: Add NPCM7xx timer driver") Signed-off-by: Avi Fishman <avifishman70@gmail.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The system counter block guide states that the base clock is
internally divided by 3 before use, that means the clock input of
system counter defined in DT should be base clock which is normally
from OSC, and then internally divided by 3 before use.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Maxime Ripard [Mon, 22 Jul 2019 08:12:22 +0000 (10:12 +0200)]
dt-bindings: timer: Convert Allwinner A13 HSTimer to a schema
The newer Allwinner SoCs have a High Speed Timer supported in Linux, with a
matching Device Tree binding.
Now that we have the DT validation in place, let's convert the device tree
bindings for that controller over to a YAML schemas.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Maxime Ripard [Mon, 22 Jul 2019 08:12:21 +0000 (10:12 +0200)]
clocksource: sun4i: Add missing compatibles
Newer Allwinner SoCs have different number of interrupts, let's add
different compatibles for all of them to deal with this properly.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Maxime Ripard [Mon, 22 Jul 2019 08:12:20 +0000 (10:12 +0200)]
dt-bindings: timer: Add missing compatibles
Newer Allwinner SoCs have different number of interrupts, let's add
different compatibles for all of them to deal with this properly.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Maxime Ripard [Mon, 22 Jul 2019 08:12:19 +0000 (10:12 +0200)]
dt-bindings: timer: Convert Allwinner A10 Timer to a schema
The older Allwinner SoCs have a Timer supported in Linux, with a matching
Device Tree binding.
While the original binding only mentions one interrupt, the timer actually
has 6 of them.
Now that we have the DT validation in place, let's convert the device tree
bindings for that controller over to a YAML schemas.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Stephen Boyd [Tue, 30 Jul 2019 18:15:04 +0000 (11:15 -0700)]
clocksource: Remove dev_err() usage after platform_get_irq()
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
Vitaly Kuznetsov [Thu, 22 Aug 2019 08:36:30 +0000 (10:36 +0200)]
clocksource/drivers/hyperv: Enable TSC page clocksource on 32bit
There is no particular reason to not enable TSC page clocksource on
32-bit. mul_u64_u64_shr() is available and despite the increased
computational complexity (compared to 64bit) TSC page is still a huge win
compared to MSR-based clocksource.
Tianyu Lan [Wed, 14 Aug 2019 12:32:16 +0000 (20:32 +0800)]
clocksource/drivers/hyperv: Add Hyper-V specific sched clock function
Hyper-V guests use the default native_sched_clock() in
pv_ops.time.sched_clock on x86. But native_sched_clock() directly uses the
raw TSC value, which can be discontinuous in a Hyper-V VM.
Add the generic hv_setup_sched_clock() to set the sched clock function
appropriately. On x86, this sets pv_ops.time.sched_clock to read the
Hyper-V reference TSC value that is scaled and adjusted to be continuous.
Also move the Hyper-V reference TSC initialization much earlier in the boot
process so no discontinuity is observed when pv_ops.time.sched_clock
calculates its offset.
Prepare to add Hyper-V sched clock callback and move Hyper-V Reference TSC
initialization much earlier in the boot process. Earlier initialization is
needed so that it happens while the timestamp value is still 0 and no
discontinuity in the timestamp will occur when pv_ops.time.sched_clock
calculates its offset.
The earlier initialization requires that the Hyper-V TSC page be allocated
statically instead of with vmalloc(), so fixup the references to the TSC
page and the method of getting its physical address.
Thomas Gleixner [Mon, 19 Aug 2019 14:31:46 +0000 (16:31 +0200)]
posix-cpu-timers: Sanitize bogus WARNONS
Warning when p == NULL and then proceeding and dereferencing p does not
make any sense as the kernel will crash with a NULL pointer dereference
right away.
Bailing out when p == NULL and returning an error code does not cure the
underlying problem which caused p to be NULL. Though it might allow to
do proper debugging.
Same applies to the clock id check in set_process_cpu_timer().
Clean them up and make them return without trying to do further damage.
Julien Grall [Wed, 21 Aug 2019 09:24:09 +0000 (10:24 +0100)]
hrtimer: Don't take expiry_lock when timer is currently migrated
migration_base is used as a placeholder when an hrtimer is migrated to a
different CPU. In the case that hrtimer_cancel_wait_running() hits a timer
which is currently migrated it would pointlessly acquire the expiry lock of
the migration base, which is even not initialized.
Surely it could be initialized, but there is absolutely no point in
acquiring this lock because the timer is guaranteed not to run it's
callback for which the caller waits to finish on that base. So it would
just do the inc/lock/dec/unlock dance for nothing.
As the base switch is short and non-preemptible, there is no issue when the
wait function returns immediately.
The timer base and base->cpu_base cannot be NULL in the code path which is
invoking that, so just replace those checks with a check whether base is
migration base.
Julien Grall [Wed, 21 Aug 2019 09:24:07 +0000 (10:24 +0100)]
hrtimer: Protect lockless access to timer->base
The update to timer->base is protected by the base->cpu_base->lock().
However, hrtimer_cancel_wait_running() does access it lockless. So the
compiler is allowed to refetch timer->base which can cause havoc when the
timer base is changed concurrently.
Thomas Gleixner [Mon, 19 Aug 2019 14:31:43 +0000 (16:31 +0200)]
alarmtimers: Avoid rtc.h include
rtc.h is not needed in alarmtimers when a forward declaration of struct
rtc_device is provided. That allows to include posix-timers.h without
adding more includes to alarmtimer.h or creating circular include
dependencies.
Thomas Gleixner [Mon, 19 Aug 2019 14:31:42 +0000 (16:31 +0200)]
posix-timers: Cleanup forward declarations and includes
- Rename struct siginfo to kernel_siginfo as that is used and required
- Add a forward declaration for task_struct and remove sched.h include
- Remove timex.h include as it is not needed
Thomas Gleixner [Fri, 2 Aug 2019 05:35:59 +0000 (07:35 +0200)]
posix-timers: Use a callback for cancel synchronization on PREEMPT_RT
Posix timer delete retry loops are affected by the same priority inversion
and live lock issues as the other timers.
Provide a RT specific synchronization function which keeps a reference to
the timer by holding rcu read lock to prevent the timer from being freed,
dropping the timer lock and invoking the timer specific wait function via a
new callback.
This does not yet cover posix CPU timers because they need more special
treatment on PREEMPT_RT.
[ This is folded into the original attempt which did not use a callback. ]
Timer deletion on PREEMPT_RT is prone to priority inversion and live
locks. The hrtimer code has a synchronization mechanism for this. Posix CPU
timers will grow one.
But that mechanism cannot be invoked while holding the k_itimer lock
because that can deadlock against the running timer callback. So the lock
must be dropped which allows the timer to be freed.
The timer free can be prevented by taking RCU readlock before dropping the
lock, but because the rcu_head is part of the 'it' union a concurrent free
will overwrite the hrtimer on which the task is trying to synchronize.
Move the rcu_head out of the union to prevent this.
Thomas Gleixner [Tue, 30 Jul 2019 22:33:53 +0000 (00:33 +0200)]
posix-timers: Rework cancel retry loops
As a preparatory step for adding the PREEMPT RT specific synchronization
mechanism to wait for a running timer callback, rework the timer cancel
retry loops so they call a common function. This allows trivial
substitution in one place.
Use the hrtimer_cancel_wait_running() synchronization mechanism to prevent
priority inversion and live locks on PREEMPT_RT.
As a benefit the retry loop gains the missing cpu_relax() on !RT.
[ tglx: Split out of combo patch ]
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20190730223828.690771827@linutronix.de
Use the hrtimer_cancel_wait_running() synchronization mechanism to prevent
priority inversion and live locks on PREEMPT_RT.
[ tglx: Split out of combo patch ]
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20190730223828.600085866@linutronix.de
Use the hrtimer_cancel_wait_running() synchronization mechanism to prevent
priority inversion and live locks on PREEMPT_RT.
[ tglx: Split out of combo patch ]
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20190730223828.508744705@linutronix.de
When PREEMPT_RT is enabled, the soft interrupt thread can be preempted. If
the soft interrupt thread is preempted in the middle of a timer callback,
then calling del_timer_sync() can lead to two issues:
- If the caller is on a remote CPU then it has to spin wait for the timer
handler to complete. This can result in unbound priority inversion.
- If the caller originates from the task which preempted the timer
handler on the same CPU, then spin waiting for the timer handler to
complete is never going to end.
To avoid these issues, add a new lock to the timer base which is held
around the execution of the timer callbacks. If del_timer_sync() detects
that the timer callback is currently running, it blocks on the expiry
lock. When the callback is finished, the expiry lock is dropped by the
softirq thread which wakes up the waiter and the system makes progress.
This addresses both the priority inversion and the life lock issues.
This mechanism is not used for timers which are marked IRQSAFE as for those
preemption is disabled accross the callback and therefore this situation
cannot happen. The callbacks for such timers need to be individually
audited for RT compliance.
The same issue can happen in virtual machines when the vCPU which runs a
timer callback is scheduled out. If a second vCPU of the same guest calls
del_timer_sync() it will spin wait for the other vCPU to be scheduled back
in. The expiry lock mechanism would avoid that. It'd be trivial to enable
this when paravirt spinlocks are enabled in a guest, but it's not clear
whether this is an actual problem in the wild, so for now it's an RT only
mechanism.
As the softirq thread can be preempted with PREEMPT_RT=y, the SMP variant
of del_timer_sync() needs to be used on UP as well.
[ tglx: Refactored it for mainline ]
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20190726185753.832418500@linutronix.de
When PREEMPT_RT is enabled, the soft interrupt thread can be preempted. If
the soft interrupt thread is preempted in the middle of a timer callback,
then calling hrtimer_cancel() can lead to two issues:
- If the caller is on a remote CPU then it has to spin wait for the timer
handler to complete. This can result in unbound priority inversion.
- If the caller originates from the task which preempted the timer
handler on the same CPU, then spin waiting for the timer handler to
complete is never going to end.
To avoid these issues, add a new lock to the timer base which is held
around the execution of the timer callbacks. If hrtimer_cancel() detects
that the timer callback is currently running, it blocks on the expiry
lock. When the callback is finished, the expiry lock is dropped by the
softirq thread which wakes up the waiter and the system makes progress.
This addresses both the priority inversion and the life lock issues.
The same issue can happen in virtual machines when the vCPU which runs a
timer callback is scheduled out. If a second vCPU of the same guest calls
hrtimer_cancel() it will spin wait for the other vCPU to be scheduled back
in. The expiry lock mechanism would avoid that. It'd be trivial to enable
this when paravirt spinlocks are enabled in a guest, but it's not clear
whether this is an actual problem in the wild, so for now it's an RT only
mechanism.
[ tglx: Refactored it for mainline ]
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20190726185753.737767218@linutronix.de
hrtimer: Determine hard/soft expiry mode for hrtimer sleepers on RT
On PREEMPT_RT enabled kernels hrtimers which are not explicitely marked for
hard interrupt expiry mode are moved into soft interrupt context either for
latency reasons or because the hrtimer callback takes regular spinlocks or
invokes other functions which are not suitable for hard interrupt context
on PREEMPT_RT.
The hrtimer_sleeper callback is RT compatible in hard interrupt context,
but there is a latency concern: Untrusted userspace can spawn many threads
which arm timers for the same expiry time on the same CPU. On expiry that
causes a latency spike due to the wakeup of a gazillion threads.
OTOH, priviledged real-time user space applications rely on the low latency
of hard interrupt wakeups. These syscall related wakeups are all based on
hrtimer sleepers.
If the current task is in a real-time scheduling class, mark the mode for
hard interrupt expiry.
[ tglx: Split out of a larger combo patch. Added changelog ]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20190726185753.645792403@linutronix.de
hrtimer: Move unmarked hrtimers to soft interrupt expiry on RT
On PREEMPT_RT not all hrtimers can be expired in hard interrupt context
even if that is perfectly fine on a PREEMPT_RT=n kernel, e.g. because they
take regular spinlocks. Also for latency reasons PREEMPT_RT tries to defer
most hrtimers' expiry into softirq context.
hrtimers marked with HRTIMER_MODE_HARD must be kept in hard interrupt
context expiry mode. Add the required logic.
No functional change for PREEMPT_RT=n kernels.
[ tglx: Split out of a larger combo patch. Added changelog ]
tick: Mark tick related hrtimers to expiry in hard interrupt context
The tick related hrtimers, which drive the scheduler tick and hrtimer based
broadcasting are required to expire in hard interrupt context for obvious
reasons.
Mark them so PREEMPT_RT kernels wont move them to soft interrupt expiry.
Make the horribly formatted RCU_NONIDLE bracket maze readable while at it.
No functional change,
[ tglx: Split out from larger combo patch. Add changelog ]
KVM: LAPIC: Mark hrtimer to expire in hard interrupt context
On PREEMPT_RT enabled kernels unmarked hrtimers are moved into soft
interrupt expiry mode by default.
While that's not a functional requirement for the KVM local APIC timer
emulation, it's a latency issue which can be avoided by marking the timer
so hard interrupt context expiry is enforced.
No functional change.
[ tglx: Split out from larger combo patch. Add changelog. ]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Paolo Bonzini <pbonzini@redhat.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20190726185753.363363474@linutronix.de
watchdog: Mark watchdog_hrtimer to expire in hard interrupt context
The watchdog hrtimer must expire in hard interrupt context even on
PREEMPT_RT=y kernels as otherwise the hard/softlockup detection logic would
not work.
No functional change.
[ tglx: Split out from larger combo patch. Added changelog ]
perf/core: Mark hrtimers to expire in hard interrupt context
To guarantee that the multiplexing mechanism and the hrtimer driven events
work on PREEMPT_RT enabled kernels it's required that the related hrtimers
expire in hard interrupt context. Mark them so PREEMPT_RT kernels wont
defer them to soft interrupt context.
No functional change.
[ tglx: Split out of larger combo patch. Added changelog ]
Thomas Gleixner [Tue, 30 Jul 2019 18:15:25 +0000 (20:15 +0200)]
hrtimer: Make enqueue mode check work on RT
hrtimer_start_range_ns() has a WARN_ONCE() which verifies that a timer
which is marker for softirq expiry is not queued in the hard interrupt base
and vice versa.
When PREEMPT_RT is enabled, timers which are not explicitely marked to
expire in hard interrupt context are deferrred to the soft interrupt. So
the regular check would trigger.
Change the check, so when PREEMPT_RT is enabled, it is verified that the
timers marked for hard interrupt expiry are not tried to be queued for soft
interrupt expiry or any of the unmarked and softirq marked is tried to be
expired in hard interrupt context.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
On PREEMPT_RT not all hrtimers can be expired in hard interrupt context
even if that is perfectly fine on a PREEMPT_RT=n kernel, e.g. because they
take regular spinlocks. Also for latency reasons PREEMPT_RT tries to defer
most hrtimers' expiry into soft interrupt context.
But there are hrtimers which must be expired in hard interrupt context even
when PREEMPT_RT is enabled:
- hrtimers which must expiry in hard interrupt context, e.g. scheduler,
perf, watchdog related hrtimers
- latency critical hrtimers, e.g. nanosleep, ..., kvm lapic timer
Add a new mode flag HRTIMER_MODE_HARD which allows to mark these timers so
PREEMPT_RT will not move them into softirq expiry mode.
[ tglx: Split out of a larger combo patch. Added changelog ]
Thomas Gleixner [Tue, 30 Jul 2019 19:16:55 +0000 (21:16 +0200)]
hrtimer/treewide: Use hrtimer_sleeper_start_expires()
hrtimer_sleepers will gain a scheduling class dependent treatment on
PREEMPT_RT. Use the new hrtimer_sleeper_start_expires() function to make
that possible.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Tue, 30 Jul 2019 19:03:53 +0000 (21:03 +0200)]
hrtimer: Provide hrtimer_sleeper_start_expires()
hrtimer_sleepers will gain a scheduling class dependent treatment on
PREEMPT_RT. Create a wrapper around hrtimer_start_expires() to make that
possible.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
hrtimer_init_sleeper() calls require prior initialisation of the hrtimer
object which is embedded into the hrtimer_sleeper.
Combine the initialization and spare a function call. Fixup all call sites.
This is also a preparatory change for PREEMPT_RT to do hrtimer sleeper
specific initializations of the embedded hrtimer without modifying any of
the call sites.
No functional change.
[ anna-maria: Minor cleanups ]
[ tglx: Adopted to the removal of the task argument of
hrtimer_init_sleeper() and trivial polishing.
Folded a fix from Stephen Rothwell for the vsoc code ]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20190726185752.887468908@linutronix.de
lib/timerqueue: Rely on rbtree semantics for next timer
Simplify the timerqueue code by using cached rbtrees and rely on the tree
leftmost node semantics to get the timer with earliest expiration time.
This is a drop in conversion, and therefore semantics remain untouched.
The runtime overhead of cached rbtrees is be pretty much the same as the
current head->next method, noting that when removing the leftmost node,
a common operation for the timerqueue, the rb_next(leftmost) is O(1) as
well, so the next timer will either be the right node or its parent.
Therefore no extra pointer chasing. Finally, the size of the struct
timerqueue_head remains the same.
Merge branch 'parisc-5.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
- Fix build issues when kprobes are enabled
- Speed up ITLB/DTLB cache flushes when running on machines with
combined TLBs
* 'parisc-5.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Flush ITLB in flush_tlb_all_local() only on split TLB machines
parisc: add kprobe_fault_handler()
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull preemption Kconfig fix from Thomas Gleixner:
"The PREEMPT_RT stub config renamed PREEMPT to PREEMPT_LL and defined
PREEMPT outside of the menu and made it selectable by both PREEMPT_LL
and PREEMPT_RT.
Stupid me missed that 114 defconfigs select CONFIG_PREEMPT which
obviously can't work anymore. oldconfig builds are affected as well,
but it's more obvious as the user gets asked. [old]defconfig silently
fixes it up and selects PREEMPT_NONE.
Unbreak it by undoing the rename and adding a intermediate config
symbol which is selected by both PREEMPT and PREEMPT_RT. That requires
to chase down a few #ifdefs, but it's better than tweaking 114
defconfigs and annoying users"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/rt, Kconfig: Unbreak def/oldconfig with CONFIG_PREEMPT=y
Merge tag 'for-5.3-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
- fixes for leaks caused by recently merged patches
- one build fix
- a fix to prevent mixing of incompatible features
* tag 'for-5.3-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: don't leak extent_map in btrfs_get_io_geometry()
btrfs: free checksum hash on in close_ctree
btrfs: Fix build error while LIBCRC32C is module
btrfs: inode: Don't compress if NODATASUM or NODATACOW set
Thomas Gleixner [Mon, 22 Jul 2019 15:59:19 +0000 (17:59 +0200)]
sched/rt, Kconfig: Unbreak def/oldconfig with CONFIG_PREEMPT=y
The merge of the CONFIG_PREEMPT_RT stub renamed CONFIG_PREEMPT to
CONFIG_PREEMPT_LL which causes all defconfigs which have CONFIG_PREEMPT=y
set to fall back to CONFIG_PREEMPT_NONE because CONFIG_PREEMPT depends on
the preemption mode choice wich defaults to NONE. This also affects
oldconfig builds.
So rather than changing 114 defconfig files and being an annoyance to
users, revert the rename and select a new config symbol PREEMPTION. That
keeps everything working smoothly and the revelant ifdef's are going to be
fixed up step by step.
Reported-by: Mark Rutland <mark.rutland@arm.com> Fixes: a50a3f4b6a31 ("sched/rt, Kconfig: Introduce CONFIG_PREEMPT_RT") Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Merge tag 'media/v5.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"For two regressions in media core:
- v4l2-subdev: fix regression in check_pad()
- videodev2.h: change V4L2_PIX_FMT_BGRA444 define: fourcc was already
in use"
* tag 'media/v5.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: videodev2.h: change V4L2_PIX_FMT_BGRA444 define: fourcc was already in use
media: v4l2-subdev: fix regression in check_pad()
1) Several netfilter fixes including a nfnetlink deadlock fix from
Florian Westphal and fix for dropping VRF packets from Miaohe Lin.
2) Flow offload fixes from Pablo Neira Ayuso including a fix to restore
proper block sharing.
3) Fix r8169 PHY init from Thomas Voegtle.
4) Fix memory leak in mac80211, from Lorenzo Bianconi.
5) Missing NULL check on object allocation in cxgb4, from Navid
Emamdoost.
6) Fix scaling of RX power in sfp phy driver, from Andrew Lunn.
7) Check that there is actually an ip header to access in skb->data in
VRF, from Peter Kosyh.
8) Remove spurious rcu unlock in hv_netvsc, from Haiyang Zhang.
9) One more tweak the the TCP fragmentation memory limit changes, to be
less harmful to applications setting small SO_SNDBUF values. From
Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (40 commits)
tcp: be more careful in tcp_fragment()
hv_netvsc: Fix extra rcu_read_unlock in netvsc_recv_callback()
vrf: make sure skb->data contains ip header to make routing
connector: remove redundant input callback from cn_dev
qed: Prefer pcie_capability_read_word()
igc: Prefer pcie_capability_read_word()
cxgb4: Prefer pcie_capability_read_word()
be2net: Synchronize be_update_queues with dev_watchdog
bnx2x: Prevent load reordering in tx completion processing
net: phy: sfp: hwmon: Fix scaling of RX power
net: sched: verify that q!=NULL before setting q->flags
chelsio: Fix a typo in a function name
allocate_flower_entry: should check for null deref
net: hns3: typo in the name of a constant
kbuild: add net/netfilter/nf_tables_offload.h to header-test blacklist.
tipc: Fix a typo
mac80211: don't warn about CW params when not using them
mac80211: fix possible memory leak in ieee80211_assign_beacon
nl80211: fix NL80211_HE_MAX_CAPABILITY_LEN
nl80211: fix VENDOR_CMD_RAW_DATA
...
There is a race between reading task->exit_state in pidfd_poll and
writing it after do_notify_parent calls do_notify_pidfd. Expected
sequence of events is:
CPU 0 CPU 1
------------------------------------------------
exit_notify
do_notify_parent
do_notify_pidfd
tsk->exit_state = EXIT_DEAD
pidfd_poll
if (tsk->exit_state)
However nothing prevents the following sequence:
CPU 0 CPU 1
------------------------------------------------
exit_notify
do_notify_parent
do_notify_pidfd
pidfd_poll
if (tsk->exit_state)
tsk->exit_state = EXIT_DEAD
This causes a polling task to wait forever, since poll blocks because
exit_state is 0 and the waiting task is not notified again. A stress
test continuously doing pidfd poll and process exits uncovered this bug.
To fix it, we make sure that the task's exit_state is always set before
calling do_notify_pidfd.
Fixes: b53b0b9d9a6 ("pidfd: add polling support") Cc: kernel-team@android.com Cc: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Suren Baghdasaryan <surenb@google.com> Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org> Link: https://lore.kernel.org/r/20190717172100.261204-1-joel@joelfernandes.org
[christian@brauner.io: adapt commit message and drop unneeded changes from wait_task_zombie] Signed-off-by: Christian Brauner <christian@brauner.io>
Eric Dumazet [Fri, 19 Jul 2019 18:52:33 +0000 (11:52 -0700)]
tcp: be more careful in tcp_fragment()
Some applications set tiny SO_SNDBUF values and expect
TCP to just work. Recent patches to address CVE-2019-11478
broke them in case of losses, since retransmits might
be prevented.
We should allow these flows to make progress.
This patch allows the first and last skb in retransmit queue
to be split even if memory limits are hit.
It also adds the some room due to the fact that tcp_sendmsg()
and tcp_sendpage() might overshoot sk_wmem_queued by about one full
TSO skb (64KB size). Note this allowance was already present
in stable backports for kernels < 4.15
Note for < 4.15 backports :
tcp_rtx_queue_tail() will probably look like :
Fixes: f070ef2ac667 ("tcp: tcp_fragment() should apply sane memory limits") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Andrew Prout <aprout@ll.mit.edu> Tested-by: Andrew Prout <aprout@ll.mit.edu> Tested-by: Jonathan Lemon <jonathan.lemon@gmail.com> Tested-by: Michal Kubecek <mkubecek@suse.cz> Acked-by: Neal Cardwell <ncardwell@google.com> Acked-by: Yuchung Cheng <ycheng@google.com> Acked-by: Christoph Paasch <cpaasch@apple.com> Cc: Jonathan Looney <jtl@netflix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
hv_netvsc: Fix extra rcu_read_unlock in netvsc_recv_callback()
There is an extra rcu_read_unlock left in netvsc_recv_callback(),
after a previous patch that removes RCU from this function.
This patch removes the extra RCU unlock.
Fixes: 345ac08990b8 ("hv_netvsc: pass netvsc_device to receive callback") Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Peter Kosyh [Fri, 19 Jul 2019 08:11:47 +0000 (11:11 +0300)]
vrf: make sure skb->data contains ip header to make routing
vrf_process_v4_outbound() and vrf_process_v6_outbound() do routing
using ip/ipv6 addresses, but don't make sure the header is available
in skb->data[] (skb_headlen() is less then header size).
Case:
1) igb driver from intel.
2) Packet size is greater then 255.
3) MPLS forwards to VRF device.
So, patch adds pskb_may_pull() calls in vrf_process_v4/v6_outbound()
functions.
Signed-off-by: Peter Kosyh <p.kosyh@gmail.com> Reviewed-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Frederick Lawler [Thu, 18 Jul 2019 02:07:42 +0000 (21:07 -0500)]
qed: Prefer pcie_capability_read_word()
Commit 8c0d3a02c130 ("PCI: Add accessors for PCI Express Capability")
added accessors for the PCI Express Capability so that drivers didn't
need to be aware of differences between v1 and v2 of the PCI
Express Capability.
Replace pci_read_config_word() and pci_write_config_word() calls with
pcie_capability_read_word() and pcie_capability_write_word().
Signed-off-by: Frederick Lawler <fred@fredlawl.com> Acked-by: Michal Kalderon <michal.kalderon@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Frederick Lawler [Thu, 18 Jul 2019 02:07:39 +0000 (21:07 -0500)]
igc: Prefer pcie_capability_read_word()
Commit 8c0d3a02c130 ("PCI: Add accessors for PCI Express Capability")
added accessors for the PCI Express Capability so that drivers didn't
need to be aware of differences between v1 and v2 of the PCI
Express Capability.
Replace pci_read_config_word() and pci_write_config_word() calls with
pcie_capability_read_word() and pcie_capability_write_word().
Signed-off-by: Frederick Lawler <fred@fredlawl.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Frederick Lawler [Thu, 18 Jul 2019 02:07:36 +0000 (21:07 -0500)]
cxgb4: Prefer pcie_capability_read_word()
Commit 8c0d3a02c130 ("PCI: Add accessors for PCI Express Capability")
added accessors for the PCI Express Capability so that drivers didn't
need to be aware of differences between v1 and v2 of the PCI
Express Capability.
Replace pci_read_config_word() and pci_write_config_word() calls with
pcie_capability_read_word() and pcie_capability_write_word().
Signed-off-by: Frederick Lawler <fred@fredlawl.com> Reviewed-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Poirier [Thu, 18 Jul 2019 01:42:18 +0000 (10:42 +0900)]
be2net: Synchronize be_update_queues with dev_watchdog
As pointed out by Firo Yang, a netdev tx timeout may trigger just before an
ethtool set_channels operation is started. be_tx_timeout(), which dumps
some queue structures, is not written to run concurrently with
be_update_queues(), which frees/allocates those queues structures. Add some
synchronization between the two.
Message-id: <CH2PR18MB31898E033896F9760D36BFF288C90@CH2PR18MB3189.namprd18.prod.outlook.com> Signed-off-by: Benjamin Poirier <bpoirier@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Brian King [Mon, 15 Jul 2019 21:41:50 +0000 (16:41 -0500)]
bnx2x: Prevent load reordering in tx completion processing
This patch fixes an issue seen on Power systems with bnx2x which results
in the skb is NULL WARN_ON in bnx2x_free_tx_pkt firing due to the skb
pointer getting loaded in bnx2x_free_tx_pkt prior to the hw_cons
load in bnx2x_tx_int. Adding a read memory barrier resolves the issue.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 21 Jul 2019 16:50:08 +0000 (18:50 +0200)]
net: phy: sfp: hwmon: Fix scaling of RX power
The RX power read from the SFP uses units of 0.1uW. This must be
scaled to units of uW for HWMON. This requires a divide by 10, not the
current 100.
With this change in place, sensors(1) and ethtool -m agree:
sff2-isa-0000
Adapter: ISA adapter
in0: +3.23 V
temp1: +33.1 C
power1: 270.00 uW
power2: 200.00 uW
curr1: +0.01 A
Laser output power : 0.2743 mW / -5.62 dBm
Receiver signal average optical power : 0.2014 mW / -6.96 dBm
Reported-by: chris.healy@zii.aero Signed-off-by: Andrew Lunn <andrew@lunn.ch> Fixes: 1323061a018a ("net: phy: sfp: Add HWMON support for module sensors") Signed-off-by: David S. Miller <davem@davemloft.net>
net: sched: verify that q!=NULL before setting q->flags
In function int tc_new_tfilter() q pointer can be NULL when adding filter
on a shared block. With recent change that resets TCQ_F_CAN_BYPASS after
filter creation, following NULL pointer dereference happens in case parent
block is shared:
allocate_flower_entry: should check for null deref
allocate_flower_entry does not check for allocation success, but tries
to deref the result. I only moved the spin_lock under null check, because
the caller is checking allocation's status at line 652.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jeremy Sowden [Sun, 21 Jul 2019 11:31:05 +0000 (12:31 +0100)]
kbuild: add net/netfilter/nf_tables_offload.h to header-test blacklist.
net/netfilter/nf_tables_offload.h includes net/netfilter/nf_tables.h
which is itself on the blacklist.
Reported-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Jeremy Sowden <jeremy@azazel.net> Acked-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 21 Jul 2019 18:39:05 +0000 (11:39 -0700)]
Merge tag 'mac80211-for-davem-2019-07-20' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
We have a handful of fixes:
* ignore bad CW parameters if we aren't using them,
instead of warning
* fix operation (and then build) with the new netlink vendor
command policy requirement
* fix a memory leak in an error path when setting beacons
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge tag 'devicetree-fixes-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree fixes from Rob Herring:
"Fix several warnings/errors in validation of binding schemas"
* tag 'devicetree-fixes-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: pinctrl: stm32: Fix missing 'clocks' property in examples
dt-bindings: iio: ad7124: Fix dtc warnings in example
dt-bindings: iio: avia-hx711: Fix avdd-supply typo in example
dt-bindings: pinctrl: aspeed: Fix AST2500 example errors
dt-bindings: pinctrl: aspeed: Fix 'compatible' schema errors
dt-bindings: riscv: Limit cpus schema to only check RiscV 'cpu' nodes
dt-bindings: Ensure child nodes are of type 'object'
Merge tag '5.3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Two fixes for stable, one that had dependency on earlier patch in this
merge window and can now go in, and a perf improvement in SMB3 open"
* tag '5.3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: update internal module number
cifs: flush before set-info if we have writeable handles
smb3: optimize open to not send query file internal info
cifs: copy_file_range needs to strip setuid bits and update timestamps
CIFS: fix deadlock in cached root handling
Qian Cai [Thu, 11 Jul 2019 16:17:45 +0000 (12:17 -0400)]
iommu/amd: fix a crash in iova_magazine_free_pfns
The commit b3aa14f02254 ("iommu: remove the mapping_error dma_map_ops
method") incorrectly changed the checking from dma_ops_alloc_iova() in
map_sg() causes a crash under memory pressure as dma_ops_alloc_iova()
never return DMA_MAPPING_ERROR on failure but 0, so the error handling
is all wrong.
Mike Rapoport [Tue, 30 Apr 2019 14:27:50 +0000 (17:27 +0300)]
hexagon: switch to generic version of pte allocation
The hexagon implementation pte_alloc_one(), pte_alloc_one_kernel(),
pte_free_kernel() and pte_free() is identical to the generic except of
lack of __GFP_ACCOUNT for the user PTEs allocation.
Switch hexagon to use generic version of these functions.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge tag 'ntb-5.3' of git://github.com/jonmason/ntb
Pull NTB updates from Jon Mason:
"New feature to add support for NTB virtual MSI interrupts, the ability
to test and use this feature in the NTB transport layer.
Also, bug fixes for the AMD and Switchtec drivers, as well as some
general patches"
* tag 'ntb-5.3' of git://github.com/jonmason/ntb: (22 commits)
NTB: Describe the ntb_msi_test client in the documentation.
NTB: Add MSI interrupt support to ntb_transport
NTB: Add ntb_msi_test support to ntb_test
NTB: Introduce NTB MSI Test Client
NTB: Introduce MSI library
NTB: Rename ntb.c to support multiple source files in the module
NTB: Introduce functions to calculate multi-port resource index
NTB: Introduce helper functions to calculate logical port number
PCI/switchtec: Add module parameter to request more interrupts
PCI/MSI: Support allocating virtual MSI interrupts
ntb_hw_switchtec: Fix setup MW with failure bug
ntb_hw_switchtec: Skip unnecessary re-setup of shared memory window for crosslink case
ntb_hw_switchtec: Remove redundant steps of switchtec_ntb_reinit_peer() function
NTB: correct ntb_dev_ops and ntb_dev comment typos
NTB: amd: Silence shift wrapping warning in amd_ntb_db_vector_mask()
ntb_hw_switchtec: potential shift wrapping bug in switchtec_ntb_init_sndev()
NTB: ntb_transport: Ensure qp->tx_mw_dma_addr is initaliazed
NTB: ntb_hw_amd: set peer limit register
NTB: ntb_perf: Clear stale values in doorbell and command SPAD register
NTB: ntb_perf: Disable NTB link after clearing peer XLAT registers
...
parisc: Flush ITLB in flush_tlb_all_local() only on split TLB machines
flush_tlb_all_local() flushes the ITLB and DTLB of the CPU.
In case the machine does not have separate ITLBs and DTLBs, use the
alternative functionality to replace the code which flushes the ITLB
with nops while keeping the code which flushes the DTLB.
Sven Schnelle [Sun, 21 Jul 2019 09:00:39 +0000 (11:00 +0200)]
parisc: add kprobe_fault_handler()
Add kprobe_fault_handler() to fix compilation for PA-RISC.
On PA-RISC we actually don't need that function as the recovery counter
is restored after interrupt. See the PA-RISC 2.0 Architecture Manual,
pg. 4-8, Figure 4-4: "Interruption Processing".
Fixes: b98cca444d28 ("mm, kprobes: generalize and rename notify_page_fault() as kprobe_page_fault()") Signed-off-by: Sven Schnelle <svens@stackframe.org> Signed-off-by: Helge Deller <deller@gmx.de>
Rob Herring [Tue, 16 Jul 2019 21:34:40 +0000 (15:34 -0600)]
dt-bindings: pinctrl: stm32: Fix missing 'clocks' property in examples
Now that examples are validated against the DT schema, an error with
required 'clocks' property missing is exposed:
Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.example.dt.yaml: \
pinctrl@40020000: gpio@0: 'clocks' is a required property
Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.example.dt.yaml: \
pinctrl@50020000: gpio@1000: 'clocks' is a required property
Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.example.dt.yaml: \
pinctrl@50020000: gpio@2000: 'clocks' is a required property
Add the missing 'clocks' properties to the examples to fix the errors.
Fixes: 2c9239c125f0 ("dt-bindings: pinctrl: Convert stm32 pinctrl bindings to json-schema") Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: linux-gpio@vger.kernel.org Cc: linux-stm32@st-md-mailman.stormreply.com Acked-by: Alexandre TORGUE <alexandre.torgue@st.com> Signed-off-by: Rob Herring <robh@kernel.org>
There's a default #size-cells and #address-cells values of 1 for
examples. For examples needing different values such as this one on a
SPI bus, they need to provide a SPI bus parent node.
Fixes: 26ae15e62d3c ("Convert AD7124 bindings documentation to YAML format.") Cc: Jonathan Cameron <jic23@kernel.org> Cc: linux-iio@vger.kernel.org Signed-off-by: Rob Herring <robh@kernel.org>
Rob Herring [Mon, 15 Jul 2019 22:48:41 +0000 (16:48 -0600)]
dt-bindings: pinctrl: aspeed: Fix AST2500 example errors
The schema examples are now validated against the schema itself. The
AST2500 pinctrl schema has a couple of errors:
Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.example.dt.yaml: \
example-0: $nodename:0: 'example-0' does not match '^(bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.example.dt.yaml: \
pinctrl: aspeed,external-nodes: [[1, 2]] is too short
Fixes: 0a617de16730 ("dt-bindings: pinctrl: aspeed: Convert AST2500 bindings to json-schema") Cc: Andrew Jeffery <andrew@aj.id.au> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Joel Stanley <joel@jms.id.au> Cc: linux-aspeed@lists.ozlabs.org Cc: linux-gpio@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Acked-by: Andrew Jeffery <andrew@aj.id.au> Signed-off-by: Rob Herring <robh@kernel.org>
The Aspeed pinctl schema have errors in the 'compatible' schema:
Documentation/devicetree/bindings/pinctrl/aspeed,ast2400-pinctrl.yaml: \
properties:compatible:enum: ['aspeed', 'ast2400-pinctrl', 'aspeed', 'g4-pinctrl'] has non-unique elements
Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.yaml: \
properties:compatible:enum: ['aspeed', 'ast2500-pinctrl', 'aspeed', 'g5-pinctrl'] has non-unique elements
Flow style sequences have to be quoted if the vales contain ','. Fix
this by using the more common one line per entry formatting.
Fixes: 0a617de16730 ("dt-bindings: pinctrl: aspeed: Convert AST2500 bindings to json-schema") Fixes: 07457937bb5c ("dt-bindings: pinctrl: aspeed: Convert AST2400 bindings to json-schema") Cc: Andrew Jeffery <andrew@aj.id.au> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Joel Stanley <joel@jms.id.au> Cc: linux-aspeed@lists.ozlabs.org Cc: linux-gpio@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Acked-by: Andrew Jeffery <andrew@aj.id.au> Signed-off-by: Rob Herring <robh@kernel.org>
Rob Herring [Wed, 26 Jun 2019 23:57:59 +0000 (17:57 -0600)]
dt-bindings: riscv: Limit cpus schema to only check RiscV 'cpu' nodes
Matching on the 'cpus' node was a bad choice because the schema is
incorrectly applied to non-RiscV cpus nodes. As we now have a common cpus
schema which checks the general structure, it is also redundant to do so
in the Risc-V CPU schema.
The downside is one could conceivably mix different architecture's cpu
nodes or have typos in the compatible string. The latter problem pretty
much exists for every schema.
Acked-by: Paul Walmsley <paul.walmsley@sifive.com> Signed-off-by: Rob Herring <robh@kernel.org>
Rob Herring [Wed, 3 Jul 2019 20:17:06 +0000 (14:17 -0600)]
dt-bindings: Ensure child nodes are of type 'object'
Properties which are child node definitions need to have an explict
type. Otherwise, a matching (DT) property can silently match when an
error is desired. Fix this up tree-wide. Once this is fixed, the
meta-schema will enforce this on any child node definitions.
Cc: Chen-Yu Tsai <wens@csie.org> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Brian Norris <computersforpeace@gmail.com> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Richard Weinberger <richard@nod.at> Cc: Vignesh Raghavendra <vigneshr@ti.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: linux-mtd@lists.infradead.org Cc: linux-gpio@vger.kernel.org Cc: linux-stm32@st-md-mailman.stormreply.com Cc: linux-spi@vger.kernel.org Acked-by: Miquel Raynal <miquel.raynal@bootlin.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Acked-by: Mark Brown <broonie@kernel.org> Acked-by: Alexandre TORGUE <alexandre.torgue@st.com> Signed-off-by: Rob Herring <robh@kernel.org>
Brian Norris [Thu, 18 Jul 2019 01:57:12 +0000 (18:57 -0700)]
mac80211: don't warn about CW params when not using them
ieee80211_set_wmm_default() normally sets up the initial CW min/max for
each queue, except that it skips doing this if the driver doesn't
support ->conf_tx. We still end up calling drv_conf_tx() in some cases
(e.g., ieee80211_reconfig()), which also still won't do anything
useful...except it complains here about the invalid CW parameters.
Let's just skip the WARN if we weren't going to do anything useful with
the parameters.
Thomas Voegtle [Sat, 20 Jul 2019 17:01:22 +0000 (19:01 +0200)]
r8169: fix RTL8168g PHY init
This fixes a copy&paste error in the original patch. Setting the wrong
register resulted in massive packet loss on some systems.
Fixes: a2928d28643e ("r8169: use paged versions of phylib MDIO access functions") Tested-by: Thomas Voegtle <tv@lio96.de> Signed-off-by: Thomas Voegtle <tv@lio96.de> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge tag 'dma-mapping-5.3-1' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping fixes from Christoph Hellwig:
"Fix various regressions:
- force unencrypted dma-coherent buffers if encryption bit can't fit
into the dma coherent mask (Tom Lendacky)
- avoid limiting request size if swiotlb is not used (me)
- fix swiotlb handling in dma_direct_sync_sg_for_cpu/device (Fugang
Duan)"
* tag 'dma-mapping-5.3-1' of git://git.infradead.org/users/hch/dma-mapping:
dma-direct: correct the physical addr in dma_direct_sync_sg_for_cpu/device
dma-direct: only limit the mapping size if swiotlb could be used
dma-mapping: add a dma_addressing_limited helper
dma-direct: Force unencrypted DMA under SME for certain DMA masks
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A set of x86 specific fixes and updates:
- The CR2 corruption fixes which store CR2 early in the entry code
and hand the stored address to the fault handlers.
- Revert a forgotten leftover of the dropped FSGSBASE series.
- Plug a memory leak in the boot code.
- Make the Hyper-V assist functionality robust by zeroing the shadow
page.
- Remove a useless check for dead processes with LDT
- Update paravirt and VMware maintainers entries.
- A few cleanup patches addressing various compiler warnings"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/entry/64: Prevent clobbering of saved CR2 value
x86/hyper-v: Zero out the VP ASSIST PAGE on allocation
x86, boot: Remove multiple copy of static function sanitize_boot_params()
x86/boot/compressed/64: Remove unused variable
x86/boot/efi: Remove unused variables
x86/mm, tracing: Fix CR2 corruption
x86/entry/64: Update comments and sanity tests for create_gap
x86/entry/64: Simplify idtentry a little
x86/entry/32: Simplify common_exception
x86/paravirt: Make read_cr2() CALLEE_SAVE
MAINTAINERS: Update PARAVIRT_OPS_INTERFACE and VMWARE_HYPERVISOR_INTERFACE
x86/process: Delete useless check for dead process with LDT
x86: math-emu: Hide clang warnings for 16-bit overflow
x86/e820: Use proper booleans instead of 0/1
x86/apic: Silence -Wtype-limits compiler warnings
x86/mm: Free sme_early_buffer after init
x86/boot: Fix memory leak in default_get_smp_config()
Revert "x86/ptrace: Prevent ptrace from clearing the FS/GS selector" and fix the test
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf tooling updates from Thomas Gleixner:
"A set of perf improvements and fixes:
perf db-export:
- Improvements in how COMM details are exported to databases for post
processing and use in the sql-viewer.py UI.
- Export switch events to the database.
BPF:
- Bump rlimit(MEMLOCK) for 'perf test bpf' and 'perf trace', just
like selftests/bpf/bpf_rlimit.h do, which makes errors due to
exhaustion of this limit, which are kinda cryptic (EPERM sometimes)
less frequent.
perf version:
- Fix segfault due to missing OPT_END(), noticed on PowerPC.
perf vendor events:
- Add JSON files for IBM s/390 machine type 8561.
perf cs-etm (ARM):
- Fix two cases of error returns not bing done properly: Invalid
ERR_PTR() use and loss of propagation error codes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (28 commits)
perf version: Fix segfault due to missing OPT_END()
perf vendor events s390: Add JSON files for machine type 8561
perf cs-etm: Return errcode in cs_etm__process_auxtrace_info()
perf cs-etm: Remove errnoeous ERR_PTR() usage in cs_etm__process_auxtrace_info
perf scripts python: export-to-postgresql.py: Export switch events
perf scripts python: export-to-sqlite.py: Export switch events
perf db-export: Export switch events
perf db-export: Factor out db_export__threads()
perf script: Add scripting operation process_switch()
perf scripts python: exported-sql-viewer.py: Use new 'has_calls' column
perf scripts python: exported-sql-viewer.py: Remove redundant semi-colons
perf scripts python: export-to-postgresql.py: Add has_calls column to comms table
perf scripts python: export-to-sqlite.py: Add has_calls column to comms table
perf db-export: Also export thread's current comm
perf db-export: Factor out db_export__comm()
perf scripts python: export-to-postgresql.py: Export comm details
perf scripts python: export-to-sqlite.py: Export comm details
perf db-export: Export comm details
perf db-export: Fix a white space issue in db_export__sample()
perf db-export: Move export__comm_thread into db_export__sample()
...
Merge branch 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull core fixes from Thomas Gleixner:
- A collection of objtool fixes which address recent fallout partially
exposed by newer toolchains, clang, BPF and general code changes.
- Force USER_DS for user stack traces
[ Note: the "objtool fixes" are not all to objtool itself, but for
kernel code that triggers objtool warnings.
Things like missing function size annotations, or code that confuses
the unwinder etc. - Linus]
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
objtool: Support conditional retpolines
objtool: Convert insn type to enum
objtool: Fix seg fault on bad switch table entry
objtool: Support repeated uses of the same C jump table
objtool: Refactor jump table code
objtool: Refactor sibling call detection logic
objtool: Do frame pointer check before dead end check
objtool: Change dead_end_function() to return boolean
objtool: Warn on zero-length functions
objtool: Refactor function alias logic
objtool: Track original function across branches
objtool: Add mcsafe_handle_tail() to the uaccess safe list
bpf: Disable GCC -fgcse optimization for ___bpf_prog_run()
x86/uaccess: Remove redundant CLACs in getuser/putuser error paths
x86/uaccess: Don't leak AC flag into fentry from mcsafe_handle_tail()
x86/uaccess: Remove ELF function annotation from copy_user_handle_tail()
x86/head/64: Annotate start_cpu0() as non-callable
x86/entry: Fix thunk function ELF sizes
x86/kvm: Don't call kvm_spurious_fault() from .fixup
x86/kvm: Replace vmx_vmenter()'s call to kvm_spurious_fault() with UD2
...