Bart Van Assche [Thu, 14 Feb 2019 22:50:57 +0000 (14:50 -0800)]
nvme: avoid that deleting a controller triggers a circular locking complaint
Rework nvme_delete_ctrl_sync() such that it does not have to wait for
queued work. This patch avoids that test nvme/008 triggers the following
complaint:
WARNING: possible circular locking dependency detected
5.0.0-rc6-dbg+ #10 Not tainted
------------------------------------------------------
nvme/7918 is trying to acquire lock: 000000009a1a7b69 ((work_completion)(&ctrl->delete_work)){+.+.}, at: __flush_work+0x379/0x410
but task is already holding lock: 00000000ef5a45b4 (kn->count#389){++++}, at: kernfs_remove_self+0x196/0x210
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
Bart Van Assche [Thu, 14 Feb 2019 22:50:54 +0000 (14:50 -0800)]
nvme-pci: check kstrtoint() return value in queue_count_set()
This patch avoids that the compiler complains about 'ret' being set
but not being used when building with W=1.
Fixes: 3b6592f70ad7 ("nvme: utilize two queue maps, one for reads and one for writes") # v5.0-rc1 Signed-off-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Hannes Reinecke [Mon, 18 Feb 2019 10:43:26 +0000 (11:43 +0100)]
nvme-multipath: round-robin I/O policy
Implement a simple round-robin I/O policy for multipathing. Path
selection is done in two rounds, first iterating across all optimized
paths, and if that doesn't return any valid paths, iterate over all
optimized and non-optimized paths. If no paths are found, use the
existing algorithm. Also add a sysfs attribute 'iopolicy' to switch
between the current NUMA-aware I/O policy and the 'round-robin' I/O
policy.
Signed-off-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Ming Lei [Tue, 19 Feb 2019 03:08:19 +0000 (11:08 +0800)]
block: avoid to READ fields of null bio
rq->bio can be NULL sometimes, such as flush request, so don't
read bio->bi_seg_front_size until this 'bio' is checked as valid.
Cc: Bart Van Assche <bvanassche@acm.org> Reported-by: Bart Van Assche <bvanassche@acm.org> Fixes: dcebd755926b0f39dd1e ("block: use bio_for_each_bvec() to compute multi-page bvec count") Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jens Axboe [Fri, 15 Feb 2019 15:43:59 +0000 (08:43 -0700)]
Merge tag 'v5.0-rc6' into for-5.1/block
Pull in 5.0-rc6 to avoid a dumb merge conflict with fs/iomap.c.
This is needed since io_uring is now based on the block branch,
to avoid a conflict between the multi-page bvecs and the bits
of io_uring that touch the core block parts.
* tag 'v5.0-rc6': (525 commits)
Linux 5.0-rc6
x86/mm: Make set_pmd_at() paravirt aware
MAINTAINERS: Update the ocores i2c bus driver maintainer, etc
blk-mq: remove duplicated definition of blk_mq_freeze_queue
Blk-iolatency: warn on negative inflight IO counter
blk-iolatency: fix IO hang due to negative inflight counter
MAINTAINERS: unify reference to xen-devel list
x86/mm/cpa: Fix set_mce_nospec()
futex: Handle early deadlock return correctly
futex: Fix barrier comment
net: dsa: b53: Fix for failure when irq is not defined in dt
blktrace: Show requests without sector
mips: cm: reprime error cause
mips: loongson64: remove unreachable(), fix loongson_poweroff().
sit: check if IPv6 enabled before calling ip6_err_gen_icmpv6_unreach()
geneve: should not call rt6_lookup() when ipv6 was disabled
KVM: nVMX: unconditionally cancel preemption timer in free_nested (CVE-2019-7221)
KVM: x86: work around leak of uninitialized stack contents (CVE-2019-7222)
kvm: fix kvm_ioctl_create_device() reference counting (CVE-2019-6974)
signal: Better detection of synchronous signals
...
Ming Lei [Fri, 15 Feb 2019 11:13:23 +0000 (19:13 +0800)]
block: kill QUEUE_FLAG_NO_SG_MERGE
Since bdced438acd83ad83a6c ("block: setup bi_phys_segments after splitting"),
physical segment number is mainly figured out in blk_queue_split() for
fast path, and the flag of BIO_SEG_VALID is set there too.
Now only blk_recount_segments() and blk_recalc_rq_segments() use this
flag.
Basically blk_recount_segments() is bypassed in fast path given BIO_SEG_VALID
is set in blk_queue_split().
For another user of blk_recalc_rq_segments():
- run in partial completion branch of blk_update_request, which is an unusual case
- run in blk_cloned_rq_check_limits(), still not a big problem if the flag is killed
since dm-rq is the only user.
Multi-page bvec is enabled now, not doing S/G merging is rather pointless with the
current setup of the I/O path, as it isn't going to save you a significant amount
of cycles.
Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Omar Sandoval <osandov@fb.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Ming Lei [Fri, 15 Feb 2019 11:13:19 +0000 (19:13 +0800)]
block: allow bio_for_each_segment_all() to iterate over multi-page bvec
This patch introduces one extra iterator variable to bio_for_each_segment_all(),
then we can allow bio_for_each_segment_all() to iterate over multi-page bvec.
Given it is just one mechannical & simple change on all bio_for_each_segment_all()
users, this patch does tree-wide change in one single patch, so that we can
avoid to use a temporary helper for this conversion.
Reviewed-by: Omar Sandoval <osandov@fb.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Ming Lei [Fri, 15 Feb 2019 11:13:18 +0000 (19:13 +0800)]
bcache: avoid to use bio_for_each_segment_all() in bch_bio_alloc_pages()
bch_bio_alloc_pages() is always called on one new bio, so it is safe
to access the bvec table directly. Given it is the only kind of this
case, open code the bvec table access since bio_for_each_segment_all()
will be changed to support for iterating over multipage bvec.
Acked-by: Coly Li <colyli@suse.de> Reviewed-by: Omar Sandoval <osandov@fb.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Ming Lei [Fri, 15 Feb 2019 11:13:17 +0000 (19:13 +0800)]
block: loop: pass multi-page bvec to iov_iter
iov_iter is implemented on bvec itererator helpers, so it is safe to pass
multi-page bvec to it, and this way is much more efficient than passing one
page in each bvec.
Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Omar Sandoval <osandov@fb.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Ming Lei [Fri, 15 Feb 2019 11:13:12 +0000 (19:13 +0800)]
block: use bio_for_each_bvec() to compute multi-page bvec count
First it is more efficient to use bio_for_each_bvec() in both
blk_bio_segment_split() and __blk_recalc_rq_segments() to compute how
many multi-page bvecs there are in the bio.
Secondly once bio_for_each_bvec() is used, the bvec may need to be
splitted because its length can be very longer than max segment size,
so we have to split the big bvec into several segments.
Thirdly when splitting multi-page bvec into segments, the max segment
limit may be reached, so the bio split need to be considered under
this situation too.
Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Omar Sandoval <osandov@fb.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Ming Lei [Fri, 15 Feb 2019 11:13:10 +0000 (19:13 +0800)]
block: introduce multi-page bvec helpers
This patch introduces helpers of 'mp_bvec_iter_*' for multi-page bvec
support.
The introduced helpers treate one bvec as real multi-page segment,
which may include more than one pages.
The existed helpers of bvec_iter_* are interfaces for supporting current
bvec iterator which is thought as single-page by drivers, fs, dm and
etc. These introduced helpers will build single-page bvec in flight, so
this way won't break current bio/bvec users, which needn't any change.
Follows some multi-page bvec background:
- bvecs stored in bio->bi_io_vec is always multi-page style
- bvec(struct bio_vec) represents one physically contiguous I/O
buffer, now the buffer may include more than one page after
multi-page bvec is supported, and all these pages represented
by one bvec is physically contiguous. Before multi-page bvec
support, at most one page is included in one bvec, we call it
single-page bvec.
- .bv_page of the bvec points to the 1st page in the multi-page bvec
- .bv_offset of the bvec is the offset of the buffer in the bvec
The effect on the current drivers/filesystem/dm/bcache/...:
- almost everyone supposes that one bvec only includes one single
page, so we keep the sp interface not changed, for example,
bio_for_each_segment() still returns single-page bvec
- bio_for_each_segment_all() will return single-page bvec too
- during iterating, iterator variable(struct bvec_iter) is always
updated in multi-page bvec style, and bvec_iter_advance() is kept
not changed
- returned(copied) single-page bvec is built in flight by bvec
helpers from the stored multi-page bvec
Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Omar Sandoval <osandov@fb.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Ming Lei [Fri, 15 Feb 2019 11:13:08 +0000 (19:13 +0800)]
block: don't use bio->bi_vcnt to figure out segment number
It is wrong to use bio->bi_vcnt to figure out how many segments
there are in the bio even though CLONED flag isn't set on this bio,
because this bio may be splitted or advanced.
So always use bio_segments() in blk_recount_segments(), and it shouldn't
cause any performance loss now because the physical segment number is figured
out in blk_queue_split() and BIO_SEG_VALID is set meantime since bdced438acd83ad83a6c ("block: setup bi_phys_segments after splitting").
Reviewed-by: Omar Sandoval <osandov@fb.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Fixes: 76d8137a3113 ("blk-merge: recaculate segment if it isn't less than max segments") Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
bio_readpage_error currently uses bi_vcnt to decide if it is worth
retrying an I/O. But the vector count is mostly an implementation
artifact - it really should figure out if there is more than a
single sector worth retrying. Use bi_size for that and shift by
PAGE_SHIFT. This really should be blocks/sectors, but given that
btrfs doesn't support a sector size different from the PAGE_SIZE
using the page size keeps the changes to a minimum.
Reviewed-by: Omar Sandoval <osandov@fb.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Heiner Litz [Mon, 11 Feb 2019 12:25:09 +0000 (13:25 +0100)]
lightnvm: pblk: fix race condition on GC
This patch fixes a race condition where a write is mapped to the last
sectors of a line. The write is synced to the device but the L2P is not
updated yet. When the line is garbage collected before the L2P update
is performed, the sectors are ignored by the GC logic and the line is
freed before all sectors are moved. When the L2P is finally updated, it
contains a mapping to a freed line, subsequent reads of the
corresponding LBAs fail.
This patch introduces a per line counter specifying the number of
sectors that are synced to the device but have not been updated in the
L2P. Lines with a counter of greater than zero will not be selected
for GC.
Signed-off-by: Heiner Litz <hlitz@ucsc.edu> Reviewed-by: Hans Holmberg <hans.holmberg@cnexlabs.com> Reviewed-by: Javier González <javier@javigon.com> Signed-off-by: Matias Bjørling <mb@lightnvm.io> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Javier González [Mon, 11 Feb 2019 12:25:08 +0000 (13:25 +0100)]
lightnvm: pblk: prevent stall due to wb threshold
In order to respect mw_cuinits, pblk's write buffer maintains a
backpointer to protect data not yet persisted; when writing to the write
buffer, this backpointer defines a threshold that pblk's rate-limiter
enforces.
On small PU configurations, the following scenarios might take place: (i)
the threshold is larger than the write buffer and (ii) the threshold is
smaller than the write buffer, but larger than the maximun allowed
split bio - 256KB at this moment (Note that writes are not always
split - we only do this when we the size of the buffer is smaller
than the buffer). In both cases, pblk's rate-limiter prevents the I/O to
be written to the buffer, thus stalling.
This patch fixes the original backpointer implementation by considering
the threshold both on buffer creation and on the rate-limiters path,
when bio_split is triggered (case (ii) above).
Fixes: 766c8ceb16fc ("lightnvm: pblk: guarantee that backpointer is respected on writer stall") Signed-off-by: Javier González <javier@javigon.com> Reviewed-by: Hans Holmberg <hans.holmberg@cnexlabs.com> Signed-off-by: Matias Bjørling <mb@lightnvm.io> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Hans Holmberg [Mon, 11 Feb 2019 12:25:07 +0000 (13:25 +0100)]
lightnvm: pblk: extend line wp balance check
pblk stripes writes of minimal write size across all non-offline chunks
in a line, which means that the maximum write pointer delta should not
exceed the minimal write size.
Extend the line write pointer balance check to cover this case, and
ignore the offline chunk wps.
This will render us a warning during recovery if something unexpected
has happened to the chunk write pointers (i.e. powerloss, a spurious
chunk reset, ..).
Masahiro Yamada [Mon, 11 Feb 2019 12:25:06 +0000 (13:25 +0100)]
lightnvm: pblk: fix TRACE_INCLUDE_PATH
As the comment block in include/trace/define_trace.h says,
TRACE_INCLUDE_PATH should be a relative path to the define_trace.h
../../drivers/lightnvm is the correct relative path.
../../../drivers/lightnvm is working by coincidence because the top
Makefile adds -I$(srctree)/arch/$(SRCARCH)/include as a header
search path, but we should not rely on it.
Andy Shevchenko [Mon, 11 Feb 2019 12:25:04 +0000 (13:25 +0100)]
lightnvm: Use u64 instead of __le64 for CPU visible side
Sparse complains about using strict data types:
drivers/lightnvm/pblk-read.c:254:43: warning: incorrect type in assignment (different base types)
drivers/lightnvm/pblk-read.c:254:43: expected restricted __le64 <noident>
drivers/lightnvm/pblk-read.c:254:43: got unsigned long long [unsigned] [usertype] <noident>
drivers/lightnvm/pblk-read.c:255:29: warning: cast from restricted __le64
drivers/lightnvm/pblk-read.c:268:29: warning: cast from restricted __le64
drivers/lightnvm/pblk-read.c:328:41: warning: incorrect type in assignment (different base types)
drivers/lightnvm/pblk-read.c:328:41: expected restricted __le64 <noident>
drivers/lightnvm/pblk-read.c:328:41: got unsigned long long [unsigned] [usertype] <noident>
In the code it seems explicit that lba_list_mem and lba_list_media members
of struct pblk_pr_ctx are used on CPU side, which means they should not be
of strict types.
Change types of lba_list_mem and lba_list_media members to be u64.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Javier González <javier@javigon.com> Signed-off-by: Matias Bjørling <mb@lightnvm.io> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Hans Holmberg [Mon, 11 Feb 2019 12:25:02 +0000 (13:25 +0100)]
lightnvm: pblk: stop taking the free lock in in pblk_lines_free
pblk_line_meta_free might sleep (it can end up calling vfree, depending
on how we allocate lba lists), and this can lead to a BUG()
if we wake up on a different cpu and release the lock.
As there is no point of grabbing the free lock when pblk has shut down,
remove the lock.
Linus Torvalds [Sun, 10 Feb 2019 18:39:37 +0000 (10:39 -0800)]
Merge tag 'dmaengine-fix-5.0-rc6' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
- Fix in at_xdmac fr wrongful channel state
- Fix for imx driver for wrong callback invocation
- Fix to bcm driver for interrupt race & transaction abort.
- Fix in dmatest to abort in mapping error
* tag 'dmaengine-fix-5.0-rc6' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: dmatest: Abort test in case of mapping error
dmaengine: bcm2835: Fix abort of transactions
dmaengine: bcm2835: Fix interrupt race on RT
dmaengine: imx-dma: fix wrong callback invoke
dmaengine: at_xdmac: Fix wrongfull report of a channel as in use
Linus Torvalds [Sun, 10 Feb 2019 17:57:42 +0000 (09:57 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"A handful of fixes:
- Fix an MCE corner case bug/crash found via MCE injection testing
- Fix 5-level paging boot crash
- Fix MCE recovery cache invalidation bug
- Fix regression on Xen guests caused by a recent PMD level mremap
speedup optimization"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Make set_pmd_at() paravirt aware
x86/mm/cpa: Fix set_mce_nospec()
x86/boot/compressed/64: Do not corrupt EDX on EFER.LME=1 setting
x86/MCE: Initialize mce.bank in the case of a fatal error in mce_no_way_out()
Linus Torvalds [Sun, 10 Feb 2019 17:54:19 +0000 (09:54 -0800)]
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Ingo Molnar:
"irqchip driver fixes: most of them are race fixes for ARM GIC (General
Interrupt Controller) variants, but also a fix for the ARM MMP
(Marvell PXA168 et al) irqchip affecting OLPC keyboards"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3-its: Fix ITT_entry_size accessor
irqchip/mmp: Only touch the PJ4 IRQ & FIQ bits on enable/disable
irqchip/gic-v3-its: Gracefully fail on LPI exhaustion
irqchip/gic-v3-its: Plug allocation race for devices sharing a DevID
irqchip/gic-v4: Fix occasional VLPI drop
Linus Torvalds [Sun, 10 Feb 2019 17:48:18 +0000 (09:48 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"A couple of kernel side fixes:
- Fix the Intel uncore driver on certain hardware configurations
- Fix a CPU hotplug related memory allocation bug
- Remove a spurious WARN()
... plus also a handful of perf tooling fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf script python: Add Python3 support to tests/attr.py
perf trace: Support multiple "vfs_getname" probes
perf symbols: Filter out hidden symbols from labels
perf symbols: Add fallback definitions for GELF_ST_VISIBILITY()
tools headers uapi: Sync linux/in.h copy from the kernel sources
perf clang: Do not use 'return std::move(something)'
perf mem/c2c: Fix perf_mem_events to support powerpc
perf tests evsel-tp-sched: Fix bitwise operator
perf/core: Don't WARN() for impossible ring-buffer sizes
perf/x86/intel: Delay memory deallocation until x86_pmu_dead_cpu()
perf/x86/intel/uncore: Add Node ID mask
blk-sysfs: Rework documention of __blk_release_queue
The Notes section of the comment was removed, because now
blk_release_queue can only be executed from blk_cleanup_queue (being
called when the q->kobj reaches zero), and also blk_init_queue was removed
in a1ce35fa4985.
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Since 4cf6324b17e9, a portion of function blk_cleanup_queue was moved to
a newly created function called blk_exit_queue, including the call of
blkcg_exit_queue. So, adjust the documenation according.
Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Juergen Gross [Sun, 10 Feb 2019 07:40:56 +0000 (08:40 +0100)]
x86/mm: Make set_pmd_at() paravirt aware
set_pmd_at() calls native_set_pmd() unconditionally on x86. This was
fine as long as only huge page entries were written via set_pmd_at(),
as Xen pv guests don't support those.
Commit 2c91bd4a4e2e53 ("mm: speed up mremap by 20x on large regions")
introduced a usage of set_pmd_at() possible on pv guests, leading to
failures like:
BUG: unable to handle kernel paging request at ffff888023e26778
#PF error: [PROT] [WRITE]
RIP: e030:move_page_tables+0x7c1/0xae0
move_vma.isra.3+0xd1/0x2d0
__se_sys_mremap+0x3c6/0x5b0
do_syscall_64+0x49/0x100
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Make set_pmd_at() paravirt aware by just letting it use set_pmd().
Fixes: 2c91bd4a4e2e53 ("mm: speed up mremap by 20x on large regions") Reported-by: Sander Eikelenboom <linux@eikelenboom.it> Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: xen-devel@lists.xenproject.org Cc: boris.ostrovsky@oracle.com Cc: sstabellini@kernel.org Cc: hpa@zytor.com Cc: bp@alien8.de Cc: torvalds@linux-foundation.org Link: https://lkml.kernel.org/r/20190210074056.11842-1-jgross@suse.com
Jens Axboe [Sat, 9 Feb 2019 22:42:07 +0000 (15:42 -0700)]
block: queue flag cleanup
We have QUEUE_FLAG_DEFAULT defined, but it's not used anymore since
the legacy IO stack is gone. Kill it.
Sanitize the queue flags in general, they use spaces (for some
reason), and the space is pretty sparse. With the flags renumbered,
we can more clearly see how many we have available.
Jens Axboe [Sat, 9 Feb 2019 22:40:24 +0000 (15:40 -0700)]
block: kill QUEUE_FLAG_FLUSH_NQ
We have various helpers for setting/clearing this flag, and also
a helper to check if the queue supports queueable flushes or not.
But nobody uses them anymore, kill it with fire.
Linus Torvalds [Sat, 9 Feb 2019 21:43:12 +0000 (13:43 -0800)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"One PM related driver bugfix and a MAINTAINERS update"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
MAINTAINERS: Update the ocores i2c bus driver maintainer, etc
i2c: omap: Use noirq system sleep pm ops to idle device for suspend
Linus Torvalds [Sat, 9 Feb 2019 20:41:14 +0000 (12:41 -0800)]
Merge tag 'mips_fixes_5.0_3' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Paul Burton:
"A batch of MIPS fixes for 5.0, nothing too scary.
- A workaround for a Loongson 3 CPU bug is the biggest change, but
still fairly straightforward. It adds extra memory barriers (sync
instructions) around atomics to avoid a CPU bug that can break
atomicity.
- Loongson64 also sees a fix for powering off some systems which
would incorrectly reboot rather than waiting for the power down
sequence to complete.
- We have DT fixes for the Ingenic JZ4740 SoC & the JZ4780-based Ci20
board, and a DT warning fix for the Nexsys4/MIPSfpga board.
- The Cavium Octeon platform sees a further fix to the behaviour of
the pcie_disable command line argument that was introduced in v3.3.
- The VDSO, introduced in v4.4, sees build fixes for configurations
of GCC that were built using the --with-fp-32= flag to specify a
default 32-bit floating point ABI.
- get_frame_info() sees a fix for configurations with
CONFIG_KALLSYMS=n, for which it previously always returned an
error.
- If the MIPS Coherence Manager (CM) reports an error then we'll now
clear that error correctly so that the GCR_ERROR_CAUSE register
will be updated with information about any future errors"
* tag 'mips_fixes_5.0_3' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
mips: cm: reprime error cause
mips: loongson64: remove unreachable(), fix loongson_poweroff().
MIPS: Remove function size check in get_frame_info()
MIPS: Use lower case for addresses in nexys4ddr.dts
MIPS: Loongson: Introduce and use loongson_llsc_mb()
MIPS: VDSO: Include $(ccflags-vdso) in o32,n32 .lds builds
MIPS: VDSO: Use same -m%-float cflag as the kernel proper
MIPS: OCTEON: don't set octeon_dma_bar_type if PCI is disabled
DTS: CI20: Fix bugs in ci20's device tree.
MIPS: DTS: jz4740: Correct interrupt number of DMA core
* tag 'for-linus-20190209' of git://git.kernel.dk/linux-block:
blk-mq: remove duplicated definition of blk_mq_freeze_queue
Blk-iolatency: warn on negative inflight IO counter
blk-iolatency: fix IO hang due to negative inflight counter
blktrace: Show requests without sector
fs: ratelimit __find_get_block_slow() failure message.
m68k: set proper major_num when specifying module param major_num
libata: Add NOLPM quirk for SAMSUNG MZ7TE512HMHP-000L1 SSD
nvme-pci: fix rapid add remove sequence
nvme: lock NS list changes while handling command effects
aio: initialize kiocb private in case any filesystems expect it.
Linus Torvalds [Sat, 9 Feb 2019 18:17:01 +0000 (10:17 -0800)]
Merge tag 'mtd/fixes-for-5.0-rc6' of git://git.infradead.org/linux-mtd
Pull mtd fixes from Boris Brezillon:
- Fix a problem with the imx28 ECC engine
- Remove a debug trace introduced in 2b6f0090a333 ("mtd: Check
add_mtd_device() ret code")
- Make sure partitions of size 0 can be registered
- Fix kernel-doc warning in the rawnand core
- Fix the error path of spinand_init() (missing manufacturer cleanup in
a few places)
- Address a problem with the SPI NAND PROGRAM LOAD operation which does
not work as expected on some parts.
* tag 'mtd/fixes-for-5.0-rc6' of git://git.infradead.org/linux-mtd:
mtd: rawnand: gpmi: fix MX28 bus master lockup problem
mtd: Make sure mtd->erasesize is valid even if the partition is of size 0
mtd: Remove a debug trace in mtdpart.c
mtd: rawnand: fix kernel-doc warnings
mtd: spinand: Fix the error/cleanup path in spinand_init()
mtd: spinand: Handle the case where PROGRAM LOAD does not reset the cache
Linus Torvalds [Sat, 9 Feb 2019 17:44:08 +0000 (09:44 -0800)]
Merge tag 'for-linus-5.0-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"Two very minor fixes: one remove of a #include for an unused header
and a fix of the xen ML address in MAINTAINERS"
* tag 'for-linus-5.0-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
MAINTAINERS: unify reference to xen-devel list
arch/arm/xen: Remove duplicate header
Coly Li [Sat, 9 Feb 2019 04:53:11 +0000 (12:53 +0800)]
bcache: use (REQ_META|REQ_PRIO) to indicate bio for metadata
In 'commit 752f66a75aba ("bcache: use REQ_PRIO to indicate bio for
metadata")' REQ_META is replaced by REQ_PRIO to indicate metadata bio.
This assumption is not always correct, e.g. XFS uses REQ_META to mark
metadata bio other than REQ_PRIO. This is why Nix noticed that bcache
does not cache metadata for XFS after the above commit.
Thanks to Dave Chinner, he explains the difference between REQ_META and
REQ_PRIO from view of file system developer. Here I quote part of his
explanation from mailing list,
REQ_META is used for metadata. REQ_PRIO is used to communicate to
the lower layers that the submitter considers this IO to be more
important that non REQ_PRIO IO and so dispatch should be expedited.
IOWs, if the filesystem considers metadata IO to be more important
that user data IO, then it will use REQ_PRIO | REQ_META rather than
just REQ_META.
Then it seems bios with REQ_META or REQ_PRIO should both be cached for
performance optimation, because they are all probably low I/O latency
demand by upper layer (e.g. file system).
So in this patch, when we want to decide whether to bypass the cache,
REQ_META and REQ_PRIO are both checked. Then both metadata and
high priority I/O requests will be handled properly.
Reported-by: Nix <nix@esperi.org.uk> Signed-off-by: Coly Li <colyli@suse.de> Reviewed-by: Andre Noll <maan@tuebingen.mpg.de> Tested-by: Nix <nix@esperi.org.uk> Cc: stable@vger.kernel.org Cc: Dave Chinner <david@fromorbit.com> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Coly Li [Sat, 9 Feb 2019 04:53:10 +0000 (12:53 +0800)]
bcache: fix input overflow to cache set sysfs file io_error_halflife
Cache set sysfs entry io_error_halflife is used to set c->error_decay.
c->error_decay is in type unsigned int, and it is converted by
strtoul_or_return(), therefore overflow to c->error_decay is possible
for a large input value.
This patch fixes the overflow by using strtoul_safe_clamp() to convert
input string to an unsigned long value in range [0, UINT_MAX], then
divides by 88 and set it to c->error_decay.
Signed-off-by: Coly Li <colyli@suse.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Coly Li [Sat, 9 Feb 2019 04:53:09 +0000 (12:53 +0800)]
bcache: fix input overflow to cache set io_error_limit
c->error_limit is in type unsigned int, it is set via cache set sysfs
file io_error_limit. Inside the bcache code, input string is converted
by strtoul_or_return() and set the converted value to c->error_limit.
Because the converted value is unsigned long, and c->error_limit is
unsigned int, if the input is large enought, overflow will happen to
c->error_limit.
This patch uses sysfs_strtoul_clamp() to convert input string, and set
the range in [0, UINT_MAX] to avoid the potential overflow.
Signed-off-by: Coly Li <colyli@suse.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Coly Li [Sat, 9 Feb 2019 04:53:08 +0000 (12:53 +0800)]
bcache: fix input overflow to journal_delay_ms
c->journal_delay_ms is in type unsigned short, it is set via sysfs
interface and converted by sysfs_strtoul() from input string to
unsigned short value. Therefore overflow to unsigned short might be
happen when the converted value exceed USHRT_MAX. e.g. writing
65536 into sysfs file journal_delay_ms, c->journal_delay_ms is set to
0.
This patch uses sysfs_strtoul_clamp() to convert the input string and
limit value range in [0, USHRT_MAX], to avoid the input overflow.
Signed-off-by: Coly Li <colyli@suse.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Coly Li [Sat, 9 Feb 2019 04:53:07 +0000 (12:53 +0800)]
bcache: fix input overflow to writeback_rate_minimum
dc->writeback_rate_minimum is type unsigned integer variable, it is set
via sysfs interface, and converte from input string to unsigned integer
by d_strtoul_nonzero(). When the converted input value is larger than
UINT_MAX, overflow to unsigned integer happens.
This patch fixes the overflow by using sysfs_strotoul_clamp() to
convert input string and limit the value in range [1, UINT_MAX], then
the overflow can be avoided.
Signed-off-by: Coly Li <colyli@suse.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Coly Li [Sat, 9 Feb 2019 04:53:06 +0000 (12:53 +0800)]
bcache: fix potential div-zero error of writeback_rate_p_term_inverse
Current code already uses d_strtoul_nonzero() to convert input string
to an unsigned integer, to make sure writeback_rate_p_term_inverse
won't be zero value. But overflow may happen when converting input
string to an unsigned integer value by d_strtoul_nonzero(), then
dc->writeback_rate_p_term_inverse can still be set to 0 even if the
sysfs file input value is not zero, e.g. 4294967296 (a.k.a UINT_MAX+1).
If dc->writeback_rate_p_term_inverse is set to 0, it might cause a
dev-zero error in following code from __update_writeback_rate(),
int64_t proportional_scaled =
div_s64(error, dc->writeback_rate_p_term_inverse);
This patch replaces d_strtoul_nonzero() by sysfs_strtoul_clamp() and
limit the value range in [1, UINT_MAX]. Then the unsigned integer
overflow and dev-zero error can be avoided.
Signed-off-by: Coly Li <colyli@suse.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Coly Li [Sat, 9 Feb 2019 04:53:05 +0000 (12:53 +0800)]
bcache: fix potential div-zero error of writeback_rate_i_term_inverse
dc->writeback_rate_i_term_inverse can be set via sysfs interface. It is
in type unsigned int, and convert from input string by d_strtoul(). The
problem is d_strtoul() does not check valid range of the input, if 4294967296 is written into sysfs file writeback_rate_i_term_inverse,
an overflow of unsigned integer will happen and value 0 is set to
dc->writeback_rate_i_term_inverse.
In writeback.c:__update_writeback_rate(), there are following lines of
code,
integral_scaled = div_s64(dc->writeback_rate_integral,
dc->writeback_rate_i_term_inverse);
If dc->writeback_rate_i_term_inverse is set to 0 via sysfs interface,
a div-zero error might be triggered in the above code.
Therefore we need to add a range limitation in the sysfs interface,
this is what this patch does, use sysfs_stroul_clamp() to replace
d_strtoul() and restrict the input range in [1, UINT_MAX].
Signed-off-by: Coly Li <colyli@suse.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Coly Li [Sat, 9 Feb 2019 04:53:04 +0000 (12:53 +0800)]
bcache: fix input overflow to writeback_delay
Sysfs file writeback_delay is used to configure dc->writeback_delay
which is type unsigned int. But bcache code uses sysfs_strtoul() to
convert the input string, therefore it might be overflowed if the input
value is too large. E.g. input value is 4294967296 but indeed 0 is
set to dc->writeback_delay.
This patch uses sysfs_strtoul_clamp() to convert the input string and
set the result value range in [0, UINT_MAX] to avoid such unsigned
integer overflow.
Signed-off-by: Coly Li <colyli@suse.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Coly Li [Sat, 9 Feb 2019 04:53:03 +0000 (12:53 +0800)]
bcache: use sysfs_strtoul_bool() to set bit-field variables
When setting bcache parameters via sysfs, there are some variables are
defined as bit-field value. Current bcache code in sysfs.c uses either
d_strtoul() or sysfs_strtoul() to convert the input string to unsigned
integer value and set it to the corresponded bit-field value.
The problem is, the bit-field value only takes the lowest bit of the
converted value. If input is 2, the expected value (like bool value)
of the bit-field value should be 1, but indeed it is 0.
The following sysfs files for bit-field variables have such problem,
bypass_torture_test, for dc->bypass_torture_test
writeback_metadata, for dc->writeback_metadata
writeback_running, for dc->writeback_running
verify, for c->verify
key_merging_disabled, for c->key_merging_disabled
gc_always_rewrite, for c->gc_always_rewrite
btree_shrinker_disabled,for c->shrinker_disabled
copy_gc_enabled, for c->copy_gc_enabled
This patch uses sysfs_strtoul_bool() to set such bit-field variables,
then if the converted value is non-zero, the bit-field variables will
be set to 1, like setting a bool value like expensive_debug_checks.
Signed-off-by: Coly Li <colyli@suse.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Coly Li [Sat, 9 Feb 2019 04:53:02 +0000 (12:53 +0800)]
bcache: add sysfs_strtoul_bool() for setting bit-field variables
When setting bool values via sysfs interface, e.g. writeback_metadata,
if writing 1 into writeback_metadata file, dc->writeback_metadata is
set to 1, but if writing 2 into the file, dc->writeback_metadata is
0. This is misleading, a better result should be 1 for all non-zero
input value.
It is because dc->writeback_metadata is a bit-field variable, and
current code simply use d_strtoul() to convert a string into integer
and takes the lowest bit value. To fix such error, we need a routine
to convert the input string into unsigned integer, and set target
variable to 1 if the converted integer is non-zero.
This patch introduces a new macro called sysfs_strtoul_bool(), it can
be used to convert input string into bool value, we can use it to set
bool value for bit-field vairables.
Signed-off-by: Coly Li <colyli@suse.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Coly Li [Sat, 9 Feb 2019 04:53:01 +0000 (12:53 +0800)]
bcache: fix input overflow to sequential_cutoff
People may set sequential_cutoff of a cached device via sysfs file,
but current code does not check input value overflow. E.g. if value 4294967295 (UINT_MAX) is written to file sequential_cutoff, its value
is 4GB, but if 4294967296 (UINT_MAX + 1) is written into, its value
will be 0. This is an unexpected behavior.
This patch replaces d_strtoi_h() by sysfs_strtoul_clamp() to convert
input string to unsigned integer value, and limit its range in
[0, UINT_MAX]. Then the input overflow can be fixed.
Signed-off-by: Coly Li <colyli@suse.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Coly Li [Sat, 9 Feb 2019 04:53:00 +0000 (12:53 +0800)]
bcache: fix input integer overflow of congested threshold
Cache set congested threshold values congested_read_threshold_us and
congested_write_threshold_us can be set via sysfs interface. These
two values are 'unsigned int' type, but sysfs interface uses strtoul
to convert input string. So if people input a large number like 9999999999, the value indeed set is 1410065407, which is not expected
behavior.
This patch replaces sysfs_strtoul() by sysfs_strtoul_clamp() when
convert input string to unsigned int value, and set value range in
[0, UINT_MAX], to avoid the above integer overflow errors.
Signed-off-by: Coly Li <colyli@suse.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Coly Li [Sat, 9 Feb 2019 04:52:59 +0000 (12:52 +0800)]
bcache: improve sysfs_strtoul_clamp()
Currently sysfs_strtoul_clamp() is defined as,
82 #define sysfs_strtoul_clamp(file, var, min, max) \
83 do { \
84 if (attr == &sysfs_ ## file) \
85 return strtoul_safe_clamp(buf, var, min, max) \
86 ?: (ssize_t) size; \
87 } while (0)
The problem is, if bit width of var is less then unsigned long, min and
max may not protect var from integer overflow, because overflow happens
in strtoul_safe_clamp() before checking min and max.
To fix such overflow in sysfs_strtoul_clamp(), to make min and max take
effect, this patch adds an unsigned long variable, and uses it to macro
strtoul_safe_clamp() to convert an unsigned long value in range defined
by [min, max]. Then assign this value to var. By this method, if bit
width of var is less than unsigned long, integer overflow won't happen
before min and max are checking.
Now sysfs_strtoul_clamp() can properly handle smaller data type like
unsigned int, of cause min and max should be defined in range of
unsigned int too.
Signed-off-by: Coly Li <colyli@suse.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Tang Junhui [Sat, 9 Feb 2019 04:52:58 +0000 (12:52 +0800)]
bcache: treat stale && dirty keys as bad keys
Stale && dirty keys can be produced in the follow way:
After writeback in write_dirty_finish(), dirty keys k1 will
replace by clean keys k2
==>ret = bch_btree_insert(dc->disk.c, &keys, NULL, &w->key);
==>btree_insert_fn(struct btree_op *b_op, struct btree *b)
==>static int bch_btree_insert_node(struct btree *b,
struct btree_op *op,
struct keylist *insert_keys,
atomic_t *journal_ref,
Then two steps:
A) update k1 to k2 in btree node memory;
bch_btree_insert_keys(b, op, insert_keys, replace_key)
B) Write the bset(contains k2) to cache disk by a 30s delay work
bch_btree_leaf_dirty(b, journal_ref).
But before the 30s delay work write the bset to cache device,
these things happened:
A) GC works, and reclaim the bucket k2 point to;
B) Allocator works, and invalidate the bucket k2 point to,
and increase the gen of the bucket, and place it into free_inc
fifo;
C) Until now, the 30s delay work still does not finish work,
so in the disk, the key still is k1, it is dirty and stale
(its gen is smaller than the gen of the bucket). and then the
machine power off suddenly happens;
D) When the machine power on again, after the btree reconstruction,
the stale dirty key appear.
In bch_extent_bad(), when expensive_debug_checks is off, it would
treat the dirty key as good even it is stale keys, and it would
cause bellow probelms:
A) In read_dirty() it would cause machine crash:
BUG_ON(ptr_stale(dc->disk.c, &w->key, 0));
B) It could be worse when reads hits stale dirty keys, it would
read old incorrect data.
This patch tolerate the existence of these stale && dirty keys,
and treat them as bad key in bch_extent_bad().
(Coly Li: fix indent which was modified by sender's email client)
Coly Li [Sat, 9 Feb 2019 04:52:56 +0000 (12:52 +0800)]
bcache: export backing_dev_uuid via sysfs
When there are multiple bcache devices, after a reboot the name of
bcache devices may change (e.g. current /dev/bcache1 was /dev/bcache0
before reboot). Therefore we need the backing device UUID (sb.uuid) to
identify each bcache device.
Backing device uuid can be found by program bcache-super-show, but
directly exporting backing_dev_uuid by sysfs file
/sys/block/bcache<?>/bcache/backing_dev_uuid is a much simpler method.
With backing_dev_uuid, and partition uuids from /dev/disk/by-partuuid/,
now we can identify each bcache device and its partitions conveniently.
Signed-off-by: Coly Li <colyli@suse.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Coly Li [Sat, 9 Feb 2019 04:52:55 +0000 (12:52 +0800)]
bcache: export backing_dev_name via sysfs
This patch export dc->backing_dev_name to sysfs file
/sys/block/bcache<?>/bcache/backing_dev_name, then people or user space
tools may know the backing device name of this bcache device.
Of cause it can be done by parsing sysfs links, but this method can be
much simpler to find the link between bcache device and backing device.
Signed-off-by: Coly Li <colyli@suse.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Coly Li [Sat, 9 Feb 2019 04:52:54 +0000 (12:52 +0800)]
bcache: not use hard coded memset size in bch_cache_accounting_clear()
In stats.c:bch_cache_accounting_clear(), a hard coded number '7' is
used in memset(). It is because in struct cache_stats, there are 7
atomic_t type members. This is not good when new members added into
struct stats, the hard coded number will only clear part of memory.
This patch replaces 'sizeof(unsigned long) * 7' by more generic
'sizeof(struct cache_stats))', to avoid potential error if new
member added into struct cache_stats.
Signed-off-by: Coly Li <colyli@suse.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
We have observed it where both:
1) LVM/devmapper is involved (bcache backing device is LVM volume) and
2) writeback cache is involved (bcache cache_mode is writeback)
On one machine, we can reliably reproduce it with:
# echo writeback > /sys/block/bcache0/bcache/cache_mode
(not sure whether above line is required)
# mount /dev/bcache0 /test
# for i in {0..10}; do
file="$(mktemp /test/zero.XXX)"
dd if=/dev/zero of="$file" bs=1M count=256
sync
rm $file
done
# fstrim -v /test
Observing this with tracepoints on, we see the following writes:
Note the final one has different hit/bypass flags.
This is because in should_writeback(), we were hitting a case where
the partial stripe condition was returning true and so
should_writeback() was returning true early.
If that hadn't been the case, it would have hit the would_skip test, and
as would_skip == s->iop.bypass == true, should_writeback() would have
returned false.
Looking at the git history from 'commit 72c270612bd3 ("bcache: Write out
full stripes")', it looks like the idea was to optimise for raid5/6:
* If a stripe is already dirty, force writes to that stripe to
writeback mode - to help build up full stripes of dirty data
To fix this issue, make sure that should_writeback() on a discard op
never returns true.
More details of debugging:
https://www.spinics.net/lists/linux-bcache/msg06996.html
(Coly Li: minor modification to follow maximum 75 chars per line rule)
Cc: Kent Overstreet <koverstreet@google.com> Cc: stable@vger.kernel.org Fixes: 72c270612bd3 ("bcache: Write out full stripes") Signed-off-by: Daniel Axtens <dja@axtens.net> Signed-off-by: Coly Li <colyli@suse.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Ingo Molnar [Sat, 9 Feb 2019 12:13:45 +0000 (13:13 +0100)]
Merge tag 'perf-urgent-for-mingo-5.0-20190205' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
perf trace:
Arnaldo Carvalho de Melo:
Fix handling of probe:vfs_getname when the probed routine is
inlined in multiple places, fixing the collection of the 'filename'
parameter in open syscalls.
perf test:
Gustavo A. R. Silva:
Fix bitwise operator usage in evsel-tp-sched test, which made tat
test always detect fields as signed.
Jiri Olsa:
Filter out hidden symbols from labels, added in systems where the
annobin plugin is used, such as RHEL8, which, if left in place make
the DWARF unwind 'perf test' to fail on PPC.
Tony Jones:
Fix 'perf_event_attr' tests when building with python3.
perf mem/c2c:
Ravi Bangoria:
Fix perf_mem_events on PowerPC.
tools headers UAPI:
Arnaldo Carvalho de Melo:
Sync linux/in.h copy from the kernel sources, silencing a perf build warning.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Ingo Molnar <mingo@kernel.org>
Linus Torvalds [Sat, 9 Feb 2019 00:23:41 +0000 (16:23 -0800)]
Merge tag 'armsoc-fixes-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"This is a bit larger than normal, as we had not managed to send out a
pull request before traveling for a week without my signing key.
There are multiple code fixes for older bugs, all of which should get
backported into stable kernels:
- tango: one fix for multiplatform configurations broken on other
platforms when tango is enabled
- arm_scmi: device unregistration fix
- iop32x: fix kernel oops from extraneous __init annotation
- pxa: remove a double kfree
- fsl qbman: close an interrupt clearing race
The rest is the usual collection of smaller fixes for device tree
files, on the renesas, allwinner, meson, omap, davinci, qualcomm and
imx platforms.
Some of these are for compile-time warnings, most are for board
specific functionality that fails to work because of incorrect
settings"
* tag 'armsoc-fixes-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (30 commits)
ARM: tango: Improve ARCH_MULTIPLATFORM compatibility
firmware: arm_scmi: provide the mandatory device release callback
ARM: iop32x/n2100: fix PCI IRQ mapping
arm64: dts: add msm8996 compatible to gicv3
ARM: dts: am335x-shc.dts: fix wrong cd pin level
ARM: dts: n900: fix mmc1 card detect gpio polarity
ARM: dts: omap3-gta04: Fix graph_port warning
ARM: pxa: ssp: unneeded to free devm_ allocated data
ARM: dts: r8a7743: Convert to new LVDS DT bindings
soc: fsl: qbman: avoid race in clearing QMan interrupt
arm64: dts: renesas: r8a77965: Enable DMA for SCIF2
arm64: dts: renesas: r8a7796: Enable DMA for SCIF2
arm64: dts: renesas: r8a774a1: Enable DMA for SCIF2
ARM: dts: da850: fix interrupt numbers for clocksource
dt-bindings: imx8mq: Number clocks consecutively
arm64: dts: meson: Fix mmc cd-gpios polarity
ARM: dts: imx6sx: correct backward compatible of gpt
ARM: dts: imx: replace gpio-key,wakeup with wakeup-source property
ARM: dts: vf610-bk4: fix incorrect #address-cells for dspi3
ARM: dts: meson8m2: mxiii-plus: mark the SD card detection GPIO active-low
...
Linus Torvalds [Sat, 9 Feb 2019 00:21:33 +0000 (16:21 -0800)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Two arm64 fixes for -rc6. They resolve a kernel NULL dereference in
kexec and bogus kernel page table dumping when userspace is configured
for 52-bit virtual addressing.
Summary:
- Fix kernel oops when attemping kexec_file() with a NULL cmdline
- Fix page table output in debugfs when ARM64_USER_VA_BITS_52=y"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: kexec_file: handle empty command-line
arm64: ptdump: Don't iterate kernel page tables using PTRS_PER_PXX
Linus Torvalds [Sat, 9 Feb 2019 00:04:12 +0000 (16:04 -0800)]
Merge tag 'powerpc-5.0-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Just two fixes, both going to stable.
- Our support for split pmd page table lock had a bug which could
lead to a crash on mremap() when using the Radix MMU (Power9 only).
- A fix for the PAPR SCM driver (nvdimm) we added last release, which
had a bug where we might mis-handle a hypervisor response leading
to us failing to attach the memory region.
Thanks to: Aneesh Kumar K.V, Oliver O'Halloran"
* tag 'powerpc-5.0-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/papr_scm: Use the correct bind address
powerpc/radix: Fix kernel crash with mremap()
Linus Torvalds [Fri, 8 Feb 2019 23:39:28 +0000 (15:39 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull signal fixes from Eric Biederman:
"This contains four small fixes for signal handling. A missing range
check, a regression fix, prioritizing signals we have already started
a signal group exit for, and better detection of synchronous signals.
The confused decision of which signals to handle failed spectacularly
when a timer was pointed at SIGBUS and the stack overflowed. Resulting
in an unkillable process in an infinite loop instead of a SIGSEGV and
core dump"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
signal: Better detection of synchronous signals
signal: Always notice exiting tasks
signal: Always attempt to allocate siginfo for SIGSTOP
signal: Make siginmask safe when passed a signal of 0
Linus Torvalds [Fri, 8 Feb 2019 23:37:17 +0000 (15:37 -0800)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of five minor fixes (although, tecnhincally, the aicxxx
fix is for a major problem in that the driver won't load without it,
but I think the fact it's taken us since 4.10 to discover this
indicates that the user base for these things has declined)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: cxlflash: Prevent deadlock when adapter probe fails
Revert "scsi: libfc: Add WARN_ON() when deleting rports"
scsi: sd_zbc: Fix zone information messages
scsi: target: make the pi_prot_format ConfigFS path readable
scsi: aic94xx: fix module loading
Linus Torvalds [Fri, 8 Feb 2019 23:34:10 +0000 (15:34 -0800)]
Merge tag 'iommu-fixes-v5.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fix from Joerg Roedel:
"Intel decided to leave the newly added Scalable Mode Feature
default-disabled for now. The patch here accomplishes that"
* tag 'iommu-fixes-v5.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/vt-d: Leave scalable mode default off
Linus Torvalds [Fri, 8 Feb 2019 23:32:10 +0000 (15:32 -0800)]
Merge tag 'pci-v5.0-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fix from Bjorn Helgaas:
"Work around Synopsys duplicate Device ID (HAPS USB3, NXP i.MX) that
breaks PCIe on I.MX SoCs (Thinh Nguyen)"
* tag 'pci-v5.0-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Work around Synopsys duplicate Device ID (HAPS USB3, NXP i.MX)
Linus Torvalds [Fri, 8 Feb 2019 23:30:02 +0000 (15:30 -0800)]
Merge tag 'acpi-5.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"This prevents excessive ACPI debug messages from being printed to the
kernel log, which has started to happen after one of the recent ACPICA
commits (Erik Schmauss)"
* tag 'acpi-5.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: Set debug output flags independent of ACPICA
projects / mirror_ubuntu-focal-kernel.git / log