powerpc: Remove redundant selection of E500 and E500MC
PPC_85xx and PPC_BOOK3E_64 already select E500 so no need
to select it again by PPC_QEMU_E500 and CORENET_GENERIC
as they depend on PPC_85xx || PPC_BOOK3E_64.
PPC_BOOK3E_64 already selects E500MC so no need to
select it again by PPC_QEMU_E500 if PPC64, PPC_BOOK3E_64
is the only way into PPC_QEMU_E500 with PPC64.
powerpc/cputable: Split cpu_specs[] out of cputable.h
cpu_specs[] is full of #ifdefs depending on the different
types of CPU.
CPUs are mutually exclusive, it is therefore possible to split
cpu_specs[] into smaller more readable pieces.
Create cpu_specs_XXX.h that will each be dedicated on one
of the following mutually exclusive families:
- 40x
- 44x
- 47x
- 8xx
- e500
- book3s/32
- book3s/64
In book3s/32, the block for 603 has been moved in front in order
to not have two 604 blocks.
The only 64-bit Book3E CPUs we support require the selection
of CONFIG_PPC_E500MC.
However our Kconfig allows configurating a kernel that has 64-bit
Book3E support, but without CONFIG_PPC_E500MC enabled. Such a kernel
would never boot, it doesn't know about any CPUs.
To fix this, force CONFIG_PPC_E500MC to be selected whenever we are
building a 64-bit Book3E kernel.
And add a test to detect future situations where cpu_specs is empty.
Pali Rohár [Tue, 30 Aug 2022 22:55:00 +0000 (00:55 +0200)]
powerpc: dts: turris1x.dts: Fix NOR partitions labels
Partition partition@20000 contains generic kernel image and it does not
have to be used only for rescue purposes. Partition partition@1c0000
contains bootable rescue system and partition partition@340000 contains
factory image/data for restoring to NAND. So change partition labels to
better fit their purpose by removing possible misleading substring "rootfs"
from these labels.
Currently powerpc selects HAVE_EFFICIENT_UNALIGNED_ACCESS in all cases
but one. The exception is if the kernel is being built little endian and
explicitly targeted for Power7.
The combination of Power7 and little endian was never commercially
supported, or widely used. It was only ever possible on bare metal
machines, using unofficial firmware, or in qemu guests hosted on those
machines.
The bare metal firmware support for Power7 was removed in 2019, see
skiboot commit 16b7ae64 ("Remove POWER7 and POWER7+ support").
Little endian kernel builds were switched to target Power8 or later in
2018, in commit a73657ea19ae ("powerpc/64: Add GENERIC_CPU support for
little endian"). Since then it's only been possible to boot a Power7/LE
kernel by explicitly building for Power7.
So drop the exception and always select HAVE_EFFICIENT_UNALIGNED_ACCESS.
If anyone does still have a Power7/LE machine it should hopefully
continue to boot, just with some performance penality, and if not they
can report a bug.
powerpc/book3s: Inline first level of update_mmu_cache()
update_mmu_cache() voids when hash page tables are not used.
On PPC32 that means when MMU_FTR_HPTE_TABLE is not defined.
On PPC64 that means when RADIX is enabled.
Rename core part of update_mmu_cache() as __update_mmu_cache()
and include the initial verification in an inlined caller.
Because 64-bit Book3S uses pgtable-nop4d.h, the P4D is folded into the
PGD. So P4D entries are actually PGD entries, or vice versa.
The other way to think of it is that the P4D is a single entry page
table below the PGD. Zero bits of the address are needed to index into
the P4D, therefore a P4D entry maps the same size address space as a PGD
entry.
As explained in the previous commit, there are no huge page sizes
supported directly at the PGD level on 64-bit Book3S, so there are also
no huge page sizes supported at the P4D level.
Therefore p4d_is_leaf() can never be true, so drop the definition and
fallback to the default implementation that always returns false.
On powerpc there are two ways for huge pages to be represented in the
top level page table, aka PGD (Page Global Directory).
If the address space mapped by an individual PGD entry does not
correspond to a given huge page size, then the PGD entry points to a
non-standard page table, known as a "hugepd" (Huge Page Directory).
The hugepd contains some number of huge page PTEs sufficient to map the
address space with the given huge page size.
On the other hand, if the address space mapped by an individual PGD
entry does correspond exactly to a given huge page size, that PGD entry
is used to directly encode the huge page PTE in place. In this case the
pgd_huge() wrapper indicates to generic code that the PGD entry is
actually a huge page PTE.
This commit deals with the pgd_huge() case only, it does nothing with
respect to the hugepd case.
Over time the size of the virtual address space supported on powerpc has
increased several times, which means the location at which huge pages
can sit in the tree has also changed. There have also been new huge page
sizes added, with the introduction of the Radix MMU.
On Power9 and later with the Radix MMU, the largest huge page size in
any implementation is 1GB.
Since the introduction of Radix, 1GB entries have been supported at the
PUD level, with both 4K and 64K base page size. Radix has never had a
supported huge page size at the PGD level.
On Power8 or earlier, which uses the Hash MMU, or Power9 or later with
the Hash MMU enabled, the largest huge page size is 16GB.
Using the Hash MMU and a base page size of 4K, 16GB has never been a
supported huge page size at the PGD level, due to the geometry being
incompatible. The two supported huge page sizes (16M & 16GB) both use
the hugepd format.
Using the Hash MMU and a base page size of 64K, 16GB pages were
supported in the past at the PGD level.
However in commit ba95b5d03596 ("powerpc/mm/book3s/64: Rework page table
geometry for lower memory usage") the page table layout was reworked to
shrink the size of the PGD.
As a result the 16GB page size now fits at the PUD level when using 64K
base page size.
Therefore there are no longer any supported configurations where
pgd_huge() can be true, so drop the definitions for pgd_huge(), and
fallback to the generic definition which is always false.
Michael Ellerman [Mon, 19 Sep 2022 05:27:55 +0000 (15:27 +1000)]
powerpc/microwatt: Remove unused early debug code
The original microwatt submission[1] included some early debug code for
using the Microwatt "potato" UART.
The series that was eventually merged switched to using a standard UART,
and so doesn't need any special early debug handling. But some of the
original code was merged accidentally under the non-existent
CONFIG_PPC_EARLY_DEBUG_MICROWATT.
Fixes: 48b545b8018d ("powerpc/microwatt: Use standard 16550 UART for console") Reported-by: Lukas Bulwahn <lukas.bulwahn@gmail.com> Reviewed-by: Andrew Donnellan <ajd@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20220919052755.800907-1-mpe@ellerman.id.au
Nicholas Piggin [Fri, 16 Sep 2022 04:07:55 +0000 (14:07 +1000)]
powerpc/build: put sys_call_table in .data.rel.ro if RELOCATABLE
Const function pointers by convention live in .data.rel.ro if they need
to be relocated. Now that .data.rel.ro is linked into the read-only
region, put them in the right section. This doesn't make much practical
difference, but it will make the C conversion of sys_call_table a
smaller change as far as linking goes.
Nicholas Piggin [Fri, 16 Sep 2022 04:07:52 +0000 (14:07 +1000)]
powerpc/build: move .data.rel.ro, .sdata2 to read-only
.sdata2 is a readonly small data section for ppc32, and .data.rel.ro
is data that needs relocating but is read-only after that so these
can both be moved to the read only memory region.
Nicholas Piggin [Fri, 16 Sep 2022 04:07:51 +0000 (14:07 +1000)]
powerpc/build: move got, toc, plt, branch_lt sections to read-only
This moves linker-related tables from .data to read-only area.
Relocations are performed at early boot time before memory is protected,
after which there should be no modifications required.
Nicholas Piggin [Fri, 16 Sep 2022 04:07:49 +0000 (14:07 +1000)]
powerpc: move __end_rodata to cover arch read-only sections
powerpc has a number of read-only sections and tables that are put after
RO_DATA(). Move the __end_rodata symbol to cover these as well.
Setting memory to read-only at boot is done using __init_begin, change
that to use __end_rodata.
This makes is_kernel_rodata() exactly cover the read-only region, as
well as other things using __end_rodata (e.g., kernel/dma/debug.c).
Boot dmesg also prints the rodata size more accurately.
Michael Ellerman [Fri, 16 Sep 2022 04:41:24 +0000 (14:41 +1000)]
powerpc/vmlinux.lds: Add an explicit symbol for the SRWX boundary
Currently __init_begin is used as the boundary for strict RWX between
executable/read-only text and data, and non-executable (after boot) code
and data.
But that's a little subtle, so add an explicit symbol to document that
the SRWX boundary lies there, and add a comment making it clear that
__init_begin must also begin there.
Nicholas Piggin [Mon, 26 Sep 2022 05:38:23 +0000 (15:38 +1000)]
powerpc/pseries: move hcall_tracepoint_refcount out of .toc
The .toc section is not really intended for arbitrary data. Writable
data in particular prevents making the TOC read-only after relocation.
Move hcall_tracepoint_refcount into the .data section.
Gaosheng Cui [Tue, 13 Sep 2022 07:50:29 +0000 (15:50 +0800)]
KVM: PPC: remove orphan declarations from kvm_ppc.h
Remove the following orphan declarations from kvm_ppc.h:
1. kvmppc_mmu_priv_switch() has been removed since
commit dd9ebf1f9435 ("KVM: PPC: e500: Add shadow PID
support").
2. kvmppc_core_destroy_mmu() has been removed since
commit ecc0981ff07c ("KVM: ppc: cosmetic changes to mmu
hook names").
3. kvmppc_prepare_vrma() has been removed since
commit aa04b4cc5be6 ("KVM: PPC: Allocate RMAs (Real Mode
Areas) at boot for use by guests").
So remove the declarations for them from header file.
Gaosheng Cui [Tue, 13 Sep 2022 07:50:25 +0000 (15:50 +0800)]
powerpc/mm: remove orphan declarations from mmu_context.h
Remove the following orphan declarations from mmu_context.h:
1. switch_cop() and drop_cop() have been removed since
commit 6ff4d3e96652 ("powerpc: Remove old unused icswx
based coprocessor support").
2. mm_iommu_cleanup() has been removed since
commit 4b6fad7097f8 ("powerpc/mm/iommu, vfio/spapr: Put
pages on VFIO container shutdown").
So remove the declarations for them from header file.
Gaosheng Cui [Tue, 13 Sep 2022 07:50:22 +0000 (15:50 +0800)]
powerpc/spufs: remove orphan declarations from spufs.h
Remove the following orphan declarations from spufs.h:
1. spufs_coredump_calls has been removed since
commit 48cad41f7ee7 ("[POWERPC] spufs: Combine
spufs_coredump_calls with spufs_calls").
2. spufs_coredump_num_notes has been removed since
commit 936d5bf1d7dc ("[POWERPC] spufs: Get rid of spufs_coredump_num_notes,
it's not needed if we NULL terminate").
At the time this was submitted by Leonardo, I confirmed -- or thought
I had confirmed -- with PowerVM partition firmware development that
the following RTAS functions:
Recent discussion with firmware development makes it clear that this
is not true, and that the code in commit b664db8e3f97 ("powerpc/rtas:
Implement reentrant rtas call") is unsafe, likely explaining several
strange bugs we've seen in internal testing involving DLPAR and
LPM. These scenarios use ibm,configure-connector, whose internal state
can be corrupted by the concurrent use of the "reentrant" functions,
leading to symptoms like endless busy statuses from RTAS.
Nicholas Piggin [Thu, 1 Sep 2022 11:03:34 +0000 (21:03 +1000)]
powerpc/64s: add pte_needs_flush and huge_pmd_needs_flush
Allow PTE changes to avoid flushing the TLB when access permissions are
being relaxed, the dirty bit is being set, and the accessed bit is being
changed.
Relaxing access permissions and setting dirty and accessed bits do not
require a flush because the MMU will re-load the PTE and notice the
updates (it may also cause a spurious fault).
Clearing the accessed bit does not require a flush because of the
imprecise PTE accessed bit accounting that is already performed, as
documented in ptep_clear_flush_young().
This reduces TLB flushing for some mprotect(2) calls.
arch/powerpc/math-emu/fre.c:6:5: error: no previous prototype for 'fre' [-Werror=missing-prototypes]
arch/powerpc/math-emu/fsqrt.c:11:1: error: no previous prototype for 'fsqrt' [-Werror=missing-prototypes]
arch/powerpc/math-emu/fsqrts.c:12:1: error: no previous prototype for 'fsqrts' [-Werror=missing-prototypes]
arch/powerpc/math-emu/frsqrtes.c:6:5: error: no previous prototype for 'frsqrtes' [-Werror=missing-prototypes]
arch/powerpc/math-emu/mtfsf.c:10:1: error: no previous prototype for 'mtfsf' [-Werror=missing-prototypes]
arch/powerpc/math-emu/mtfsfi.c:10:1: error: no previous prototype for 'mtfsfi' [-Werror=missing-prototypes]
arch/powerpc/math-emu/fabs.c:7:1: error: no previous prototype for 'fabs' [-Werror=missing-prototypes]
arch/powerpc/math-emu/fadd.c:11:1: error: no previous prototype for 'fadd' [-Werror=missing-prototypes]
arch/powerpc/math-emu/fadds.c:12:1: error: no previous prototype for 'fadds' [-Werror=missing-prototypes]
arch/powerpc/math-emu/fcmpo.c:11:1: error: no previous prototype for 'fcmpo' [-Werror=missing-prototypes]
arch/powerpc/math-emu/fcmpu.c:11:1: error: no previous prototype for 'fcmpu' [-Werror=missing-prototypes]
arch/powerpc/math-emu/fcmpu.c:14:19: error: variable 'B_c' set but not used [-Werror=unused-but-set-variable]
arch/powerpc/math-emu/fcmpu.c:13:19: error: variable 'A_c' set but not used [-Werror=unused-but-set-variable]
arch/powerpc/math-emu/fctiw.c:11:1: error: no previous prototype for 'fctiw' [-Werror=missing-prototypes]
arch/powerpc/math-emu/fctiwz.c:11:1: error: no previous prototype for 'fctiwz' [-Werror=missing-prototypes]
arch/powerpc/math-emu/fdiv.c:11:1: error: no previous prototype for 'fdiv' [-Werror=missing-prototypes]
arch/powerpc/math-emu/fdivs.c:12:1: error: no previous prototype for 'fdivs' [-Werror=missing-prototypes]
arch/powerpc/math-emu/fmadd.c:11:1: error: no previous prototype for 'fmadd' [-Werror=missing-prototypes]
arch/powerpc/math-emu/fmadds.c:12:1: error: no previous prototype for 'fmadds' [-Werror=missing-prototypes]
arch/powerpc/math-emu/fmsub.c:11:1: error: no previous prototype for 'fmsub' [-Werror=missing-prototypes]
arch/powerpc/math-emu/fmsubs.c:12:1: error: no previous prototype for 'fmsubs' [-Werror=missing-prototypes]
arch/powerpc/math-emu/fmul.c:11:1: error: no previous prototype for 'fmul' [-Werror=missing-prototypes]
arch/powerpc/math-emu/fmuls.c:12:1: error: no previous prototype for 'fmuls' [-Werror=missing-prototypes]
arch/powerpc/math-emu/fnabs.c:7:1: error: no previous prototype for 'fnabs' [-Werror=missing-prototypes]
arch/powerpc/math-emu/fneg.c:7:1: error: no previous prototype for 'fneg' [-Werror=missing-prototypes]
arch/powerpc/math-emu/fnmadd.c:11:1: error: no previous prototype for 'fnmadd' [-Werror=missing-prototypes]
arch/powerpc/math-emu/fnmadds.c:12:1: error: no previous prototype for 'fnmadds' [-Werror=missing-prototypes]
arch/powerpc/math-emu/fnmsub.c:11:1: error: no previous prototype for 'fnmsub' [-Werror=missing-prototypes]
arch/powerpc/math-emu/fnmsubs.c:12:1: error: no previous prototype for 'fnmsubs' [-Werror=missing-prototypes]
arch/powerpc/math-emu/fres.c:7:1: error: no previous prototype for 'fres' [-Werror=missing-prototypes]
arch/powerpc/math-emu/frsp.c:12:1: error: no previous prototype for 'frsp' [-Werror=missing-prototypes]
arch/powerpc/math-emu/fsel.c:11:1: error: no previous prototype for 'fsel' [-Werror=missing-prototypes]
arch/powerpc/math-emu/lfs.c:12:1: error: no previous prototype for 'lfs' [-Werror=missing-prototypes]
arch/powerpc/math-emu/frsqrte.c:7:1: error: no previous prototype for 'frsqrte' [-Werror=missing-prototypes]
arch/powerpc/math-emu/fsub.c:11:1: error: no previous prototype for 'fsub' [-Werror=missing-prototypes]
arch/powerpc/math-emu/fsubs.c:12:1: error: no previous prototype for 'fsubs' [-Werror=missing-prototypes]
arch/powerpc/math-emu/mcrfs.c:10:1: error: no previous prototype for 'mcrfs' [-Werror=missing-prototypes]
arch/powerpc/math-emu/mffs.c:10:1: error: no previous prototype for 'mffs' [-Werror=missing-prototypes]
arch/powerpc/math-emu/mtfsb0.c:10:1: error: no previous prototype for 'mtfsb0' [-Werror=missing-prototypes]
arch/powerpc/math-emu/mtfsb1.c:10:1: error: no previous prototype for 'mtfsb1' [-Werror=missing-prototypes]
arch/powerpc/math-emu/stfiwx.c:7:1: error: no previous prototype for 'stfiwx' [-Werror=missing-prototypes]
arch/powerpc/math-emu/stfs.c:12:1: error: no previous prototype for 'stfs' [-Werror=missing-prototypes]
arch/powerpc/math-emu/fmr.c:7:1: error: no previous prototype for 'fmr' [-Werror=missing-prototypes]
arch/powerpc/math-emu/lfd.c:10:1: error: no previous prototype for 'lfd' [-Werror=missing-prototypes]
arch/powerpc/math-emu/stfd.c:7:1: error: no previous prototype for 'stfd' [-Werror=missing-prototypes]
arch/powerpc/math-emu/math_efp.c:177:5: error: no previous prototype for 'do_spe_mathemu' [-Werror=missing-prototypes]
arch/powerpc/math-emu/math_efp.c:726:5: error: no previous prototype for 'speround_handler' [-Werror=missing-prototypes]
arch/powerpc/math-emu/math_efp.c:893:12: error: no previous prototype for 'spe_mathemu_init' [-Werror=missing-prototypes]
Fix the warnings in math_efp.c by adding prototypes of do_spe_mathemu()
and speround_handler() to asm/processor.h and declare spe_mathemu_init()
static.
The other warnings are benign and not worth the churn of fixing them,
expecially the 'unused-but-set-variable' which would impact the core
part of 'math-emu'.
So silence them by adding -Wno-missing-prototypes -Wno-unused-but-set-variable.
But then you get:
arch/powerpc/math-emu/fre.c:6:5: error: no previous declaration for 'fre' [-Werror=missing-declarations]
arch/powerpc/math-emu/fsqrt.c:11:1: error: no previous declaration for 'fsqrt' [-Werror=missing-declarations]
arch/powerpc/math-emu/fsqrts.c:12:1: error: no previous declaration for 'fsqrts' [-Werror=missing-declarations]
arch/powerpc/math-emu/frsqrtes.c:6:5: error: no previous declaration for 'frsqrtes' [-Werror=missing-declarations]
arch/powerpc/math-emu/mtfsf.c:10:1: error: no previous declaration for 'mtfsf' [-Werror=missing-declarations]
arch/powerpc/math-emu/mtfsfi.c:10:1: error: no previous declaration for 'mtfsfi' [-Werror=missing-declarations]
arch/powerpc/math-emu/fabs.c:7:1: error: no previous declaration for 'fabs' [-Werror=missing-declarations]
arch/powerpc/math-emu/fadd.c:11:1: error: no previous declaration for 'fadd' [-Werror=missing-declarations]
arch/powerpc/math-emu/fadds.c:12:1: error: no previous declaration for 'fadds' [-Werror=missing-declarations]
arch/powerpc/math-emu/fcmpo.c:11:1: error: no previous declaration for 'fcmpo' [-Werror=missing-declarations]
arch/powerpc/math-emu/fcmpu.c:11:1: error: no previous declaration for 'fcmpu' [-Werror=missing-declarations]
arch/powerpc/math-emu/fctiw.c:11:1: error: no previous declaration for 'fctiw' [-Werror=missing-declarations]
arch/powerpc/math-emu/fctiwz.c:11:1: error: no previous declaration for 'fctiwz' [-Werror=missing-declarations]
arch/powerpc/math-emu/fdiv.c:11:1: error: no previous declaration for 'fdiv' [-Werror=missing-declarations]
arch/powerpc/math-emu/fdivs.c:12:1: error: no previous declaration for 'fdivs' [-Werror=missing-declarations]
arch/powerpc/math-emu/fmadd.c:11:1: error: no previous declaration for 'fmadd' [-Werror=missing-declarations]
arch/powerpc/math-emu/fmadds.c:12:1: error: no previous declaration for 'fmadds' [-Werror=missing-declarations]
arch/powerpc/math-emu/fmsub.c:11:1: error: no previous declaration for 'fmsub' [-Werror=missing-declarations]
arch/powerpc/math-emu/fmsubs.c:12:1: error: no previous declaration for 'fmsubs' [-Werror=missing-declarations]
arch/powerpc/math-emu/fmul.c:11:1: error: no previous declaration for 'fmul' [-Werror=missing-declarations]
arch/powerpc/math-emu/fmuls.c:12:1: error: no previous declaration for 'fmuls' [-Werror=missing-declarations]
arch/powerpc/math-emu/fnabs.c:7:1: error: no previous declaration for 'fnabs' [-Werror=missing-declarations]
arch/powerpc/math-emu/fneg.c:7:1: error: no previous declaration for 'fneg' [-Werror=missing-declarations]
arch/powerpc/math-emu/fnmadd.c:11:1: error: no previous declaration for 'fnmadd' [-Werror=missing-declarations]
arch/powerpc/math-emu/fnmadds.c:12:1: error: no previous declaration for 'fnmadds' [-Werror=missing-declarations]
arch/powerpc/math-emu/fnmsub.c:11:1: error: no previous declaration for 'fnmsub' [-Werror=missing-declarations]
arch/powerpc/math-emu/fnmsubs.c:12:1: error: no previous declaration for 'fnmsubs' [-Werror=missing-declarations]
arch/powerpc/math-emu/fres.c:7:1: error: no previous declaration for 'fres' [-Werror=missing-declarations]
arch/powerpc/math-emu/frsp.c:12:1: error: no previous declaration for 'frsp' [-Werror=missing-declarations]
arch/powerpc/math-emu/fsel.c:11:1: error: no previous declaration for 'fsel' [-Werror=missing-declarations]
arch/powerpc/math-emu/lfs.c:12:1: error: no previous declaration for 'lfs' [-Werror=missing-declarations]
arch/powerpc/math-emu/frsqrte.c:7:1: error: no previous declaration for 'frsqrte' [-Werror=missing-declarations]
arch/powerpc/math-emu/fsub.c:11:1: error: no previous declaration for 'fsub' [-Werror=missing-declarations]
arch/powerpc/math-emu/fsubs.c:12:1: error: no previous declaration for 'fsubs' [-Werror=missing-declarations]
arch/powerpc/math-emu/mcrfs.c:10:1: error: no previous declaration for 'mcrfs' [-Werror=missing-declarations]
arch/powerpc/math-emu/mffs.c:10:1: error: no previous declaration for 'mffs' [-Werror=missing-declarations]
arch/powerpc/math-emu/mtfsb0.c:10:1: error: no previous declaration for 'mtfsb0' [-Werror=missing-declarations]
arch/powerpc/math-emu/mtfsb1.c:10:1: error: no previous declaration for 'mtfsb1' [-Werror=missing-declarations]
arch/powerpc/math-emu/stfiwx.c:7:1: error: no previous declaration for 'stfiwx' [-Werror=missing-declarations]
arch/powerpc/math-emu/stfs.c:12:1: error: no previous declaration for 'stfs' [-Werror=missing-declarations]
arch/powerpc/math-emu/fmr.c:7:1: error: no previous declaration for 'fmr' [-Werror=missing-declarations]
arch/powerpc/math-emu/lfd.c:10:1: error: no previous declaration for 'lfd' [-Werror=missing-declarations]
arch/powerpc/math-emu/stfd.c:7:1: error: no previous declaration for 'stfd' [-Werror=missing-declarations]
As reported[1] by Nathan, the recently added plpks driver will crash if
it's built into the kernel and booted on a non-pseries machine, eg
powernv:
kernel BUG at arch/powerpc/kernel/syscall.c:39!
Oops: Exception in kernel mode, sig: 5 [#1]
LE PAGE_SIZE=64K MMU=Radix SMP NR_CPUS=2048 NUMA PowerNV
...
NIP system_call_exception+0x90/0x3d0
LR system_call_common+0xec/0x250
Call Trace:
0xc0000000035c3e10 (unreliable)
system_call_common+0xec/0x250
--- interrupt: c00 at plpar_hcall+0x38/0x60
NIP: c0000000000e4300 LR: c00000000202945c CTR: 0000000000000000
REGS: c0000000035c3e80 TRAP: 0c00 Not tainted (6.0.0-rc4)
MSR: 9000000002009033 <SF,HV,VEC,EE,ME,IR,DR,RI,LE> CR: 28000284 XER: 00000000
...
NIP plpar_hcall+0x38/0x60
LR pseries_plpks_init+0x64/0x23c
--- interrupt: c00
On powernv Linux is the hypervisor, so a hypercall just ends up going to
the syscall path, which BUGs if the syscall (hypercall) didn't come from
userspace.
The fix is simply to not probe the plpks driver on non-pseries machines.
Currently in pas_pci_init() a reference to the root node is leaked due
to a missing of_node_put(). Instead just use of_root directly.
Note that converting to of_find_compatible_node(NULL, ...) would
not be entirely equivalent, because that would check the compatible
property of the root node, whereas using of_root skips checking the root
node and start the search at the first child of the root.
Russell Currey [Sat, 27 Aug 2022 06:39:46 +0000 (16:39 +1000)]
powerpc/pasemi: Use strscpy instead of strlcpy
find_i2c_driver() contained the last usage of strlcpy() in arch/powerpc.
The return value was used to check if strlen(src) >= n, for which
strscpy() returns -E2BIG.
Liang He [Sat, 16 Jul 2022 07:43:44 +0000 (15:43 +0800)]
powerpc/powermac/udbg_scc: Add missing of_node_put()s in udbg_scc_init()
During the iteration of for_each_child_of_node(), we need to call
of_node_put() for the old references stored in to 'ch_def' and 'ch_a'
as their refcounters have been increased in last iteration.
In probe_one_macio(), call of_node_put() for the refernece 'node'
escaped out of the for_each_node_by_name() which has increased its
refcount. While the 'node' will finally escaped into a global reference,
we should still call of_node_put() in fail path which will stop global
reference creation.
Liang He [Sat, 2 Jul 2022 02:29:36 +0000 (10:29 +0800)]
powerpc/pci-common: Fix refcount bug for 'phb->dn'
In pcibios_alloc_controller(), 'phb' is allocated and escaped into
global 'hose_list'. So we should call of_node_get() when a new reference
created into 'phb->dn'. And when phb is freed, we should call
of_node_put() on it.
NOTE: This function is called in the iteration of for_each_xx in
chrp_find_bridges() and pSeries_discover_phbs(). If there is no
of_node_get(), the object may be prematurely freed.
Liang He [Mon, 20 Jun 2022 13:25:53 +0000 (21:25 +0800)]
powerpc/powernv: Add missing of_node_put()s
In these driver init functions, there are two kinds of errors:
(1) missing of_put_node() for of_find_compatible_node()'s returned
pointer (refcount incremented) in fail path or when it is not
used anymore.
(2) missing of_put_node() for 'for_each_xxx' loop's break
Liang He [Wed, 20 Jul 2022 12:45:57 +0000 (20:45 +0800)]
powerpc/fsl_pci: Remove of_node_put() when reference escaped out
In fsl_pci_assign_primary(), we should remove the of_node_put()
when breaking out of the for_each_matching_node() as the 'np'
is escaped out by global 'fsl_pci_primary'.
Liang He [Fri, 1 Jul 2022 14:01:19 +0000 (22:01 +0800)]
powerpc/85xx: Add missing of_node_get/put() in ge_imp3a_pci_assign_primary()
for_each_node_by_type() will automatically increase and decrease
the refcount during the iteration. However, there is a reference
escaped into global 'fsl_pci_primary' and we need to handle it.
Liang He [Fri, 1 Jul 2022 13:31:26 +0000 (21:31 +0800)]
powerpc/44x: Add of_node_put() when break out from for_each
In ppc47x_init_irq(), we need to call of_node_put() when there is
a break during the iteration of for_each_node_with_property() which
will automatically increase and decrease the refcount.
Liang He [Tue, 21 Jun 2022 11:17:01 +0000 (19:17 +0800)]
powerpc/pseries: Add missing of_node_put()s in hotplug-cpu.c
In pseries_cpuhp_cache_use_count() and pseries_cpuhp_detach_nodes(),
we need carefully hold the reference returned by
of_find_next_cache_node() and use it to call of_node_put() to keep
refcount balance.
Liang He [Tue, 21 Jun 2022 08:03:49 +0000 (16:03 +0800)]
powerpc/512x: Add missing of_node_put() in clock-commonclk.c
In mpc5121_clk_provide_migration_support(), hold the reference returned
by of_find_compatible_node() and use it to call of_node_put() for refcount
balance.
Liang He [Mon, 4 Jul 2022 14:52:33 +0000 (22:52 +0800)]
powerpc/sysdev/fsl_msi: Add missing of_node_put()
In fsl_setup_msi_irqs(), use of_node_put() to drop the reference
returned by of_parse_phandle().
Fixes: 895d603f945ba ("powerpc/fsl_msi: add support for the fsl, msi property in PCI nodes") Co-authored-by: Miaoqian Lin <linmq006@gmail.com> Signed-off-by: Liang He <windhl@126.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20220704145233.278539-1-windhl@126.com
Liang He [Fri, 1 Jul 2022 14:49:48 +0000 (22:49 +0800)]
powerpc/cell: Add missing of_node_put()s in cbe_regs.c
There are several bugs as following:
(1) In cbe_get_be_node(), hold the reference returned by of_find_xxx and
of_get_xxx OF APIs and use it to call of_node_put().
(2) In cbe_fill_regs_map(), same as above.
(3) In cbe_regs_init(), during the iteration of for_each_node_by_type(),
the refcount of 'cpu' will be automatically increased and decreased.
However, there is a reference escaped out into 'map->cpu_node' and
it should be properly handled.
Liang He [Sun, 19 Jun 2022 07:08:11 +0000 (15:08 +0800)]
powerpc/kernel: Add missing of_node_put() in legacy_serial.c
In find_legacy_serial_ports(), of_find_node_by_path() will return a node
pointer with refcount incremented. The reference should be dropped with
of_node_put() when it is not used anymore.
Liang He [Sat, 18 Jun 2022 07:13:53 +0000 (15:13 +0800)]
powerpc/perf: Add missing of_node_put()s in imc-pmu.c
In update_events_in_group(), of_find_node_by_phandle() will return
a node pointer with refcount incremented. The reference should be
dropped with of_node_put() in the failure path or when it is not used
anymore.
Liang He [Sat, 18 Jun 2022 02:49:30 +0000 (10:49 +0800)]
powerpc/8xx: Add missing of_node_put() in tqm8xx_setup.c
In init_ioports(), of_find_node_by_name() will return a node pointer
with refcount incremented. The reference should be dropped with
of_node_put() when it is not used anymore.
Liang He [Fri, 17 Jun 2022 12:40:45 +0000 (20:40 +0800)]
powerpc/maple: Add missing of_node_put() in time.c
In maple_get_boot_time(), of_find_compatible_node() will return
a node pointer with refcount incremented. The reference should be
dropped with of_node_put() when it is not used anymore.
Liang He [Fri, 17 Jun 2022 10:50:11 +0000 (18:50 +0800)]
powerpc/85xx: Add missing of_node_put() in sgy_cst1000
In gpio_halt_probe(), of_find_matching_node() will return a node
pointer with refcount incremented. The reference should be dropped with
of_node_put() in the failure path.
Liang He [Thu, 16 Jun 2022 14:40:07 +0000 (22:40 +0800)]
powerpc/52xx: Add missing of_node_put() in media5200.c
In media5200_init_irq(), of_find_compatible_node() will return a
node pointer with refcount incremented. The reference should be dropped
with of_node_put() in the failure path or when it is not used anymore.
Don't worry about 'fpga_np == NULL' as of_node_put() can correctly
handle that.
Liang He [Thu, 16 Jun 2022 13:29:22 +0000 (21:29 +0800)]
powerpc/85xx: Add missing of_node_put() in ksi8560.c
In ksi8560_setup_arch(), of_find_compatible_node() will return a
node pointer with refcount incremented. The reference should be dropped
with of_node_put() when it is not used anymore.
Liang He [Wed, 15 Jun 2022 14:37:03 +0000 (22:37 +0800)]
powerpc/512x: Add missing of_node_put() in mpc5121_clk_init()
In mpc5121_clk_init(), of_find_compatible_node() will return a
node pointer with refcount incremented. The reference should be dropped
with of_node_put() when it is not used anymore.
With recent binutils, the following warning appears:
VDSO32L arch/powerpc/kernel/vdso/vdso32.so.dbg
/opt/gcc-12.2.0-nolibc/powerpc64-linux/bin/../lib/gcc/powerpc64-linux/12.2.0/../../../../powerpc64-linux/bin/ld: warning: arch/powerpc/kernel/vdso/getcpu-32.o: missing .note.GNU-stack section implies executable stack
/opt/gcc-12.2.0-nolibc/powerpc64-linux/bin/../lib/gcc/powerpc64-linux/12.2.0/../../../../powerpc64-linux/bin/ld: NOTE: This behaviour is deprecated and will be removed in a future version of the linker
To avoid that, explicitly tell the linker we don't want executable
stack.
For more explanations, see commit ffcf9c5700e4 ("x86: link vdso
and boot with -z noexecstack --no-warn-rwx-segments")
powerpc/math-emu: Remove -w build flag and fix warnings
As reported by Nathan, the module_init() macro was not taken into
account because the header was missing. That means spe_mathemu_init()
was never called.
This should have been detected by gcc at build time, but due to
'-w' flag it went undetected.
Removing that flag leads to many warnings hence errors.
When building with a recent version of clang, there are a couple of
errors around the call to module_init():
arch/powerpc/math-emu/math_efp.c:927:1: error: type specifier missing, defaults to 'int'; ISO C99 and later do not support implicit int [-Wimplicit-int]
module_init(spe_mathemu_init);
^
int
arch/powerpc/math-emu/math_efp.c:927:13: error: a parameter list without types is only allowed in a function definition
module_init(spe_mathemu_init);
^
2 errors generated.
module_init() is a macro, which is not getting expanded because module.h
is not included in this file. Add the include so that the macro can
expand properly, clearing up the build failure.
Nicholas Piggin [Fri, 2 Sep 2022 08:53:16 +0000 (18:53 +1000)]
powerpc/pseries: Move dtl scanning and steal time accounting to pseries platform
dtl is the PAPR Dispatch Trace Log, which is entirely a pseries feature.
The pseries platform alrady has a file dealing with the dtl, so move
scanning for stolen time accounting there from kernel/time.c.
Nicholas Piggin [Fri, 2 Sep 2022 08:53:15 +0000 (18:53 +1000)]
powerpc/64: Remove PPC64 special case for cputime accounting default
Distro kernels tend to be moving to VIRT_CPU_ACCOUNTING_GEN, and there
is not much reason why PPC64 should be special here. Remove the special
case and make the ppc64 and pseries defconfigs use GEN accounting
(others will use TICK, as-per Kconfig defaults).
VIRT_CPU_ACCOUNTING_NATIVE does provide scaled vtime and stolen time
apportioned between system and user time, and vtime accounting is not
unconditionally enabled, and possibly other things. But it would be
better at this point to extend GEN to cover important missing features
rather than directing users back to a less used option.
CONFIG_VIRT_CPU_ACCOUNTING_GEN under pseries does not provide stolen
time accounting unless CONFIG_PARAVIRT_TIME_ACCOUNTING is enabled.
Implement this using the VPA accumulated wait counters.
Note this will not work on current KVM hosts because KVM does not
implement the VPA dispatch counters (yet). It could be implemented
with the dispatch trace log as it is for VIRT_CPU_ACCOUNTING_NATIVE,
but that is not necessary for the more limited accounting provided
by PARAVIRT_TIME_ACCOUNTING, and it is more expensive, complex, and
has downsides like potential log wrap.
From Shrikanth:
[...] it was tested on Power10 [PowerVM] Shared LPAR. system has two
LPAR. we will call first one LPAR1 and second one as LPAR2. Test was
carried out in SMT=1. Similar observation was seen in SMT=8 as well.
LPAR config header from each LPAR is below. LPAR1 is twice as big as
LPAR2. Since Both are sharing the same underlying hardware, work
stealing will happen when both the LPAR's are contending for the same
resource.
mpstat was used to check for the utilization. stress-ng has been used
as the workload. Few cases are tested. when the both LPAR are idle
there is no steal time. when LPAR1 starts running at 100% which
consumes all of the physical resource, steal time starts to get
accounted. With LPAR1 running at 100% and LPAR2 starts running, steal
time starts increasing. This is as expected. When the LPAR2 Load is
increased further, steal time increases further.
Patch is accounting for the steal time and basic tests are holding
good.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Tested-by: Shrikanth Hegde <sshegde@linux.ibm.com>
[mpe: Add SPDX tag to new paravirt_api_clock.h] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20220902085316.2071519-3-npiggin@gmail.com
Nicholas Piggin [Fri, 2 Sep 2022 08:53:13 +0000 (18:53 +1000)]
powerpc/pseries: Add wait interval counter definitions to struct lppaca
The hypervisor exposes accumulated partition scheduling interval times
in the VPA (lppaca). These can be used to implement a simple stolen time
in the guest without complex and costly dtl scanning.
projects / mirror_ubuntu-kernels.git / log