Dai Haruki [Tue, 16 Dec 2008 23:30:48 +0000 (15:30 -0800)]
gianfar: Fix VLAN HW feature related frame/buffer size calculation.
Optimize the VLAN checking logic as well.
Signed-off-by: Dai Haruki <dai.haruki@freescale.com> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dai Haruki [Tue, 16 Dec 2008 23:30:20 +0000 (15:30 -0800)]
gianfar: Fix eTSEC configuration procedure
Fix some bugs in the ethtool configuration functions:
* gfar_clean_rx_ring should not be called with interrupts disabled.
* Update last transmission time to avoid tx timeout.
* Delete redundant NETIF_F_IP_CSUM check in gfar_start_xmit
* Use netif_tx_lock_bh when reconfiguring the tx csum
Signed-off-by: Dai Haruki <dai.haruki@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Store the interrupt coalescing values in the form in which they will be
written to the interrupt coalescing registers. This puts a little overhead
into the ethtool configuration, and takes it out of the interrupt handler
Signed-off-by: Dai Haruki <dai.haruki@freescale.com> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Fleming [Tue, 16 Dec 2008 23:29:15 +0000 (15:29 -0800)]
gianfar: Convert gianfar to an of_platform_driver
Does the same for the accompanying MDIO driver, and then modifies the TBI
configuration method. The old way used fields in einfo, which no longer
exists. The new way is to create an MDIO device-tree node for each instance
of gianfar, and create a tbi-handle property to associate ethernet controllers
with the TBI PHYs they are connected to.
Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yang Hongyang [Tue, 16 Dec 2008 10:08:29 +0000 (02:08 -0800)]
ipv6: fix the outgoing interface selection order in udpv6_sendmsg()
1.When no interface is specified in an IPV6_PKTINFO ancillary data
item, the interface specified in an IPV6_PKTINFO sticky optionis
is used.
RFC3542:
6.7. Summary of Outgoing Interface Selection
This document and [RFC-3493] specify various methods that affect the
selection of the packet's outgoing interface. This subsection
summarizes the ordering among those in order to ensure deterministic
behavior.
For a given outgoing packet on a given socket, the outgoing interface
is determined in the following order:
1. if an interface is specified in an IPV6_PKTINFO ancillary data
item, the interface is used.
2. otherwise, if an interface is specified in an IPV6_PKTINFO sticky
option, the interface is used.
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yang Hongyang [Tue, 16 Dec 2008 10:07:45 +0000 (02:07 -0800)]
ipv6: fix the return interface index when get it while no message is received
When get receiving interface index while no message is received,
the the value seted with setsockopt() should be returned.
RFC 3542:
Issuing getsockopt() for the above options will return the sticky
option value i.e., the value set with setsockopt(). If no sticky
option value has been set getsockopt() will return the following
values:
- For the IPV6_PKTINFO option, it will return an in6_pktinfo
structure with ipi6_addr being in6addr_any and ipi6_ifindex being
zero.
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yang Hongyang [Tue, 16 Dec 2008 10:06:23 +0000 (02:06 -0800)]
ipv6: Add IPV6_PKTINFO sticky option support to setsockopt()
There are three reasons for me to add this support:
1.When no interface is specified in an IPV6_PKTINFO ancillary data
item, the interface specified in an IPV6_PKTINFO sticky optionis
is used.
RFC3542:
6.7. Summary of Outgoing Interface Selection
This document and [RFC-3493] specify various methods that affect the
selection of the packet's outgoing interface. This subsection
summarizes the ordering among those in order to ensure deterministic
behavior.
For a given outgoing packet on a given socket, the outgoing interface
is determined in the following order:
1. if an interface is specified in an IPV6_PKTINFO ancillary data
item, the interface is used.
2. otherwise, if an interface is specified in an IPV6_PKTINFO sticky
option, the interface is used.
2.When no IPV6_PKTINFO ancillary data is received,getsockopt() should
return the sticky option value which set with setsockopt().
RFC 3542:
Issuing getsockopt() for the above options will return the sticky
option value i.e., the value set with setsockopt(). If no sticky
option value has been set getsockopt() will return the following
values:
3.Make the setsockopt implementation POSIX compliant.
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
These 4 drivers have identical full duplex flow control resolution
functions. This patch changes them all to use one common function.
The function in question decides whether a device should enable TX and
RX flow control in a standard way (IEEE 802.3-2005 table 28B-3), so this
should also be useful for other drivers.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Divy Le Ray [Tue, 16 Dec 2008 09:51:47 +0000 (01:51 -0800)]
cxgb3: untie strict FW matching
The NIC driver can work with mutliple versions of the FW.
Let the driver load when the embedded FW does not match,
and the FW update mechanism failed.
The iWARP module will make its own loading decision.
Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Baruch Siach [Mon, 15 Dec 2008 20:18:52 +0000 (20:18 +0000)]
enc28j60: use netif_rx_ni() to deliver RX packets
The enc28j60 driver reads incoming packets in the process (workqueue) context,
not in a tasklet or the interrupt context. Thus, we should use netif_rx_ni()
to deliver those packets to the networking layer, instead of netif_rx(). This
way incoming packets don't wait in the incoming queue for the next IRQ to be
serviced.
Signed-off-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
Sakari Ailus [Tue, 16 Dec 2008 09:44:05 +0000 (01:44 -0800)]
tlan: Fix small (< 64 bytes) datagram transmissions
The TLAN chip does not support tranmissions smaller than 64
bytes. Smaller transfers need to be padded up to that size. This was
broken by commit id 41873e9aff0632d80c74380d58a89e8d420151bd ("tlan:
get rid of padding buffer").
James Chapman [Tue, 16 Dec 2008 09:23:49 +0000 (01:23 -0800)]
l2tp: fix UDP checksum support
The pppol2tp driver has had broken UDP checksum code for a long
time. This patch fixes it. If UDP checksums are enabled in the
tunnel's UDP socket, the L2TP driver now properly validates the
checksum on receive and fills in the checksum on transmit. If the
network device has hardware checksum support and is enabled, it is
used instead of generating/checking the checksum in software.
Signed-off-by: James Chapman <jchapman@katalix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an inconsistency in nfnetlink_conntrack.h that
I introduced myself. The problem is that CTA_NAT_SEQ_UNSPEC is
missing from enum ctattr_natseq. This inconsistency may lead to
problems in the message parsing in userspace (if the message
contains the CTA_NAT_SEQ_* attributes, of course).
This patch breaks backward compatibility, however, the only known
client of this code is libnetfilter_conntrack which indeed crashes
because it assumes the existence of CTA_NAT_SEQ_UNSPEC to do
the parsing.
The CTA_NAT_SEQ_* attributes were introduced in 2.6.25.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Hannes Eder [Tue, 16 Dec 2008 09:17:33 +0000 (01:17 -0800)]
isdn: eicon: fix sparse warning: make global functions static
Fix this sparse warnings by making the functions static:
drivers/isdn/hardware/eicon/di.c:356:6: warning: symbol 'isdn_rc' was not declared. Should it be static?
drivers/isdn/hardware/eicon/di.c:558:6: warning: symbol 'isdn_ind' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:595:6: warning: symbol 'api_parse' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:634:6: warning: symbol 'api_save_msg' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:666:6: warning: symbol 'api_load_msg' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:3417:6: warning: symbol 'manufacturer_req' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:3745:6: warning: symbol 'manufacturer_res' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:4077:6: warning: symbol 'control_rc' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:4743:6: warning: symbol 'data_rc' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:4779:6: warning: symbol 'data_ack' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:4805:6: warning: symbol 'sig_ind' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:6173:6: warning: symbol 'SendInfo' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:6349:6: warning: symbol 'SendMultiIE' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:6468:6: warning: symbol 'nl_ind' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:7250:6: warning: symbol 'get_plci' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:7409:6: warning: symbol 'add_d' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:7427:6: warning: symbol 'add_ai' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:7448:6: warning: symbol 'add_b1' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:7912:6: warning: symbol 'add_b23' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:8709:6: warning: symbol 'nl_req_ncci' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:8731:6: warning: symbol 'send_req' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:8866:6: warning: symbol 'listen_check' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:8909:6: warning: symbol 'IndParse' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:8994:6: warning: symbol 'ie_compare' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:9003:6: warning: symbol 'find_cip' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:9071:6: warning: symbol 'SetVoiceChannel' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:9089:6: warning: symbol 'VoiceChannelOff' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:9102:6: warning: symbol 'AdvCodecSupport' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:9198:6: warning: symbol 'CodecIdCheck' was not declared. Should it be static?
Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
It seems that pimlen arg could be left out as well and
eq-sizedness of structs trapped with BUILD_BUG_ON but
I don't think that's more than a cosmetic flaw since there
aren't that many args anyway.
Compile tested.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Tue, 16 Dec 2008 07:44:31 +0000 (23:44 -0800)]
ethtool: Add GGRO and SGRO ops
This patch adds the ethtool ops to enable and disable GRO. It also
makes GRO depend on RX checksum offload much the same as how TSO
depends on SG support.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Tue, 16 Dec 2008 07:43:36 +0000 (23:43 -0800)]
tcp: Add GRO support
This patch adds the TCP-specific portion of GRO. The criterion for
merging is extremely strict (the TCP header must match exactly apart
from the checksum) so as to allow refragmentation. Otherwise this
is pretty much identical to LRO, except that we support the merging
of ECN packets.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Tue, 16 Dec 2008 07:42:33 +0000 (23:42 -0800)]
net: Add skb_gro_receive
This patch adds the helper skb_gro_receive to merge packets for
GRO. The current method is to allocate a new header skb and then
chain the original packets to its frag_list. This is done to
make it easier to integrate into the existing GSO framework.
In future as GSO is moved into the drivers, we can undo this and
simply chain the original packets together.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Tue, 16 Dec 2008 07:41:09 +0000 (23:41 -0800)]
ipv4: Add GRO infrastructure
This patch adds GRO support for IPv4.
The criteria for merging is more stringent than LRO, in particular,
we require all fields in the IP header to be identical except for
the length, ID and checksum. In addition, the ID must form an
arithmetic sequence with a difference of one.
The ID requirement might seem overly strict, however, most hardware
TSO solutions already obey this rule. Linux itself also obeys this
whether GSO is in use or not.
In future we could relax this rule by storing the IDs (or rather
making sure that we don't drop them when pulling the aggregate
skb's tail).
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Tue, 16 Dec 2008 07:38:52 +0000 (23:38 -0800)]
net: Add Generic Receive Offload infrastructure
This patch adds the top-level GRO (Generic Receive Offload) infrastructure.
This is pretty similar to LRO except that this is protocol-independent.
Instead of holding packets in an lro_mgr structure, they're now held in
napi_struct.
For drivers that intend to use this, they can set the NETIF_F_GRO bit and
call napi_gro_receive instead of netif_receive_skb or just call netif_rx.
The latter will call napi_receive_skb automatically. When napi_gro_receive
is used, the driver must either call napi_complete/napi_rx_complete, or
call napi_gro_flush in softirq context if the driver uses the primitives
__napi_complete/__napi_rx_complete.
Protocols will set the gro_receive and gro_complete function pointers in
order to participate in this scheme.
In addition to the packet, gro_receive will get a list of currently held
packets. Each packet in the list has a same_flow field which is non-zero
if it is a potential match for the new packet. For each packet that may
match, they also have a flush field which is non-zero if the held packet
must not be merged with the new packet.
Once gro_receive has determined that the new skb matches a held packet,
the held packet may be processed immediately if the new skb cannot be
merged with it. In this case gro_receive should return the pointer to
the existing skb in gro_list. Otherwise the new skb should be merged into
the existing packet and NULL should be returned, unless the new skb makes
it impossible for any further merges to be made (e.g., FIN packet) where
the merged skb should be returned.
Whenever the skb is merged into an existing entry, the gro_receive
function should set NAPI_GRO_CB(skb)->same_flow. Note that if an skb
merely matches an existing entry but can't be merged with it, then
this shouldn't be set.
If gro_receive finds it pointless to hold the new skb for future merging,
it should set NAPI_GRO_CB(skb)->flush.
Held packets will be flushed by napi_gro_flush which is called by
napi_complete and napi_rx_complete.
Currently held packets are stored in a singly liked list just like LRO.
The list is limited to a maximum of 8 entries. In future, this may be
expanded to use a hash table to allow more flows to be held for merging.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Tue, 16 Dec 2008 07:27:47 +0000 (23:27 -0800)]
net: Add frag_list support to GSO
This patch allows GSO to handle frag_list in a limited way for the
purposes of allowing packets merged by GRO to be refragmented on
output.
Most hardware won't (and aren't expected to) support handling GRO
frag_list packets directly. Therefore we will perform GSO in
software for those cases.
However, for drivers that can support it (such as virtual NICs) we
may not have to segment the packets at all.
Whether the added overhead of GRO/GSO is worthwhile for bridges
and routers when weighed against the benefit of potentially
increasing the MTU within the host is still an open question.
However, for the case of host nodes this is undoubtedly a win.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Tue, 16 Dec 2008 07:26:06 +0000 (23:26 -0800)]
net: Add frag_list support to skb_segment
This patch adds limited support for handling frag_list packets in
skb_segment. The intention is to support GRO (Generic Receive Offload)
packets which will be constructed by chaining normal packets using
frag_list.
As such we require all frag_list members terminate on exact MSS
boundaries. This is checked using BUG_ON.
As there should only be one producer in the kernel of such packets,
namely GRO, this requirement should not be difficult to maintain.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 16 Dec 2008 00:31:05 +0000 (16:31 -0800)]
Merge master.kernel.org:/home/rmk/linux-2.6-arm
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 5348/1: fix documentation wrt location of the alignment trap interface
[ARM] Ensure linux/hardirqs.h is included where required
[ARM] fix kernel-doc syntax
[ARM] arch/arm/common/sa1111.c: Correct error handling code
[ARM] 5341/2: there is no copy_page on nommu ARM
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
Phonet: keep TX queue disabled when the device is off
SCHED: netem: Correct documentation comment in code.
netfilter: update rwlock initialization for nat_table
netlabel: Compiler warning and NULL pointer dereference fix
e1000e: fix double release of mutex
IA64: HP_SIMETH needs to depend upon NET
netpoll: fix race on poll_list resulting in garbage entry
ipv6: silence log messages for locally generated multicast
sungem: improve ethtool output with internal pcs and serdes
tcp: tcp_vegas cong avoid fix
sungem: Make PCS PHY support partially work again.
Rusty Russell [Mon, 15 Dec 2008 08:34:35 +0000 (19:04 +1030)]
Define smp_call_function_many for UP
Otherwise those using it in transition patches (eg. kvm) can't compile
with CONFIG_SMP=n:
arch/x86/kvm/../../../virt/kvm/kvm_main.c: In function 'make_all_cpus_request':
arch/x86/kvm/../../../virt/kvm/kvm_main.c:380: error: implicit declaration of function 'smp_call_function_many'
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Menage [Mon, 15 Dec 2008 21:54:22 +0000 (13:54 -0800)]
cgroups: fix a race between rmdir and remount
When a cgroup is removed, it's unlinked from its parent's children list,
but not actually freed until the last dentry on it is released (at which
point cgrp->root->number_of_cgroups is decremented).
Currently rebind_subsystems checks for the top cgroup's child list being
empty in order to rebind subsystems into or out of a hierarchy - this can
result in the set of subsystems bound to a hierarchy being
removed-but-not-freed cgroup.
The simplest fix for this is to forbid remounts that change the set of
subsystems on a hierarchy that has removed-but-not-freed cgroups. This
bug can be reproduced via:
ACPI toshiba: only register rfkill if bt is enabled
Part of the rfkill initialization was done whenever BT was on or not. The
following patch checks for BT presence before registering the rfkill to
the input layer. Some minor cleanups (> 80 char lines) were also added in
the process.
Signed-off-by: Frederik Deweerdt <frederik.deweerdt@gmail.com> Tested-by: Andrey Borzenkov <arvidjaar@mail.ru> Acked-by: Len Brown <len.brown@intel.com> Cc: Richard Purdie <rpurdie@rpsys.net> Acked-by: Philip Langdale <philipl@overt.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Catalin Marinas [Mon, 15 Dec 2008 21:54:16 +0000 (13:54 -0800)]
slob: do not pass the SLAB flags as GFP in kmem_cache_create()
The kmem_cache_create() function in the slob allocator passes the SLAB
flags as GFP flags to the slob_alloc() function. The patch changes this
call to pass GFP_KERNEL as the other allocators seem to do.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Acked-by: Matt Mackall <mpm@selenic.com> Cc: Cyrill Gorcunov <gorcunov@gmail.com> Cc: Christoph Lameter <cl@linux-foundation.org> Cc: Pekka Enberg <penberg@cs.helsinki.fi> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David S. Miller [Mon, 15 Dec 2008 23:14:59 +0000 (15:14 -0800)]
8390/8390p: Fix compat netdev ops handling.
Based upon a report from Randy Dunlap.
The compat netdev ops assignments need to happen in
8390.c and 8390p.c, not lib8390.c, as only the type
specific code can assign the correct function pointers.
Signed-off-by: David S. Miller <davem@davemloft.net>
Don Skidmore [Mon, 15 Dec 2008 09:06:23 +0000 (01:06 -0800)]
net: fix dcbnl_setnumtcs operation check
dcbml_setnumtcs wasn't checking for the presence of the setnumtcs
function. Instead, it was checking for setstate which was a bug.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Signed-off-by: Eric W Multanen <eric.w.multanen@intel.com> Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jesse Brandeburg [Mon, 15 Dec 2008 09:00:57 +0000 (01:00 -0800)]
ixgbe: fix dma mapping unbalance
This issue was initially reported by Joerg Roedel <joerg.roedel@amd.com>
It appears that ixgbe has had a long standing bug where it was unmapping a different size than it had mapped.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Steven Rostedt [Mon, 15 Dec 2008 08:19:14 +0000 (00:19 -0800)]
netfilter: update rwlock initialization for nat_table
The commit e099a173573ce1ba171092aee7bb3c72ea686e59
(netfilter: netns nat: per-netns NAT table) renamed the
nat_table from __nat_table to nat_table without updating the
__RW_LOCK_UNLOCKED(__nat_table.lock).
Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Zachary Amsden [Sat, 13 Dec 2008 20:36:58 +0000 (12:36 -0800)]
x86 Fix VMI crash on boot in 2.6.28-rc8
VMI initialiation can relocate the fixmap, causing early_ioremap to
malfunction if it is initialized before the relocation. To fix this,
VMI activation is split into two phases; the detection, which must
happen before setting up ioremap, and the activation, which must happen
after parsing early boot parameters.
This fixes a crash on boot when VMI is enabled under VMware.
Randy Dunlap [Mon, 1 Dec 2008 22:15:37 +0000 (14:15 -0800)]
[ARM] fix kernel-doc syntax
Fix kernel-doc notation to use correct syntax. Even though this should be
moved to where the function is actually implemented...
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We got interrupted after setting up the MAS registers before the
tlbwe and the interrupt handler that caused the interrupt also did
a kmap_atomic (ide code) and thus on returning from the interrupt
the MAS registers no longer contained the proper values.
Since we dont save/restore MAS registers for normal interrupts we
need to disable interrupts in _tlbil_va to ensure atomicity.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Ingo Brueckl [Wed, 10 Dec 2008 22:35:00 +0000 (23:35 +0100)]
console ASCII glyph 1:1 mapping
For the console, there is a 1:1 mapping of glyphs which cannot be found
in the current font. This seems to be meant as a kind of 'emergency
fallback' for fonts without unicode mapping which otherwise would
display nothing readable on the screen.
At the moment it affects all chars for which no substitution character
is defined. In particular this means that for all chars (>= 128) where
there is no iso88591-1/unicode character (e.g. control character area)
you'll get the very strange 1:1 mapping of the (cp437) graphics card
glyphs.
I'm pretty sure that the 1:1 mapping should only affect strict ASCII
code characters, i.e. chars < 128.
The patch limits the mapping as it probably was meant anyway.
Signed-off-by: Ingo Brueckl <ib@wupperonline.de> Acked-by: H. Peter Anvin <hpa@zytor.com> Cc: Egmont Koblinger <egmont@uhulinux.hu> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ingo Brueckl [Wed, 10 Dec 2008 22:34:00 +0000 (23:34 +0100)]
unicode table for cp437
There is a major bug in the cp437 to unicode translation table. Char
0x7c is mapped to U+00a5 which is the Yen sign and wrong. The right
mapping is U+00a6 (broken bar).
Furthermore, a mapping for U+00b4 (a widely used character) is missing
even though easily possible.
The patch fixes these, as well as it provides a few other useful
mappings.
The changes are as follows:
0x0f (enhancement) enables a sort of currency symbol
0x27 (bug) enables a sort of acute accent which is a widely used character
0x44 (enhancement) enables a sort of icelandic capital letter eth
0x7c (major bug) corrects mapping
0xeb (enhancement) enables a sort of icelandic small letter eth
0xee (enhancement) enables a sort of math 'element of'
Signed-off-by: Ingo Brueckl <ib@wupperonline.de> Acked-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ben Hutchings [Sat, 13 Dec 2008 06:09:38 +0000 (22:09 -0800)]
sfc: Fix synchronisation of efx_mtd_{probe,rename,remove}
Currently efx_mtd_rename() can race with the probe() and remove()
functions.
Move probe() before device registration and remove() after
unregistration. Move initialisation/update of all names based on the
netdev name into a new function and call it under the RTNL immediately
after registration.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Sat, 13 Dec 2008 06:06:24 +0000 (22:06 -0800)]
sfc: Use mutex_lock_interruptible() for ethtool EEPROM access
ethtool must contend with the MTD driver for the SPI bus lock, which
may carry out long operations such as flash erase. Allow it to be
interrupted while waiting.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Sat, 13 Dec 2008 06:05:48 +0000 (22:05 -0800)]
sfc: Specify a meaningful component for loopback RX-side and PHY tests
Our ethtool self-test result names each begin with a component name. For
some results this is "port0", which is not very meaningful. Change that
to "rx" or "phy" as appropriate.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Sat, 13 Dec 2008 05:59:24 +0000 (21:59 -0800)]
sfc: Rework MAC, PHY and board event handling
From: Steve Hodgson <shodgson@solarflare.com>
MAC, PHY and board events may be separately enabled and signalled.
Our current arrangement of chaining the polling functions can result
in events being missed. Change them to be more independent.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Sat, 13 Dec 2008 05:50:08 +0000 (21:50 -0800)]
sfc: Add support for sub-10G speeds
The SFC4000 has a separate MAC for use at sub-10G speeds. Introduce
an efx_mac_operations structure with implementations for the two MACs.
Switch between the MACs as necessary.
PHY settings are independent of the MAC, so add get_settings() and
set_settings() to efx_phy_operations. Also add macs field to indicate
which MACs the PHY is connected to.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Sat, 13 Dec 2008 05:48:57 +0000 (21:48 -0800)]
sfc: Clean up MDIO flag setting
We often want to set or clear a flag in an MDIO register, but avoid
writing if no change is required since this can have side-effects.
Encapsulate this in a function, mdio_clause45_set_flag().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Sat, 13 Dec 2008 05:42:42 +0000 (21:42 -0800)]
sfc: Don't count RX checksum errors during loopback self-test
The loopback self-test checks that IP packets with incorrect checksums
are not altered when sent on a queue with checksum generation off.
These should not contribute to RX error statistics.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Turton [Sat, 13 Dec 2008 05:41:06 +0000 (21:41 -0800)]
sfc: Add option to use a separate channel for TX completions
In a bidirectional forwarding test, we find that the best performance
is achieved by sending the TX completion interrupts from one NIC to a
CPU which shares an L2 cache with RX completion interrupts from the
other NIC. To facilitate this, add an option (through a module
parameter) to create separate channels for RX and TX completion with
separate IRQs when MSI-X is available.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-hirsute-kernel.git / log