The system doesn't more fail to bind the memory, and hence not falling
back to the PCI mode (if other failures aren't detected).
This is just a simple write down from the following patches:
agp/amd-k7: Allow binding user memory to the AGP GART
agp/hp-agp: Allow binding user memory to the AGP GART
parisc: Fix cache routines to ignore vma's with an invalid pfn
The parisc architecture does not have a pte special bit. As a result,
special mappings are handled with the VM_PFNMAP and VM_MIXEDMAP flags.
VM_MIXEDMAP mappings may or may not have a "struct page" backing. When
pfn_valid() is false, there is no "struct page" backing. Otherwise, they
are treated as normal pages.
The FireGL driver uses the VM_MIXEDMAP without a backing "struct page".
This treatment caused a panic due to a TLB data miss in
update_mmu_cache. This appeared to be in the code generated for
page_address(). We were in fact using a very circular bit of code to
determine the physical address of the PFN in various cache routines.
This wasn't valid when there was no "struct page" backing. The needed
address can in fact be determined simply from the PFN itself without
using the "struct page".
The attached patch updates update_mmu_cache(), flush_cache_mm(),
flush_cache_range() and flush_cache_page() to check pfn_valid() and to
directly compute the PFN physical and virtual addresses.
Signed-off-by: John David Anglin <dave.anglin@bell.net> Cc: <stable@vger.kernel.org> # 3.10 Signed-off-by: Helge Deller <deller@gmx.de>
1) Fix association failures not triggering a connect-failure event in
cfg80211, from Johannes Berg.
2) Eliminate a potential NULL deref with older iptables tools when
configuring xt_socket rules, from Eric Dumazet.
3) Missing RTNL locking in wireless regulatory code, from Johannes
Berg.
4) Fix OOPS caused by firmware loading races in ath9k_htc, from Alexey
Khoroshilov.
5) Fix usb URB leak in usb_8dev CAN driver, also from Alexey
Khoroshilov.
6) VXLAN namespace teardown fails to unregister devices, from Stephen
Hemminger.
7) Fix multicast settings getting dropped by firmware in qlcnic driver,
from Sucheta Chakraborty.
8) Add sysctl range enforcement for tcp_syn_retries, from Michal Tesar.
9) Fix a nasty bug in bridging where an active timer would get
reinitialized with a setup_timer() call. From Eric Dumazet.
10) Fix use after free in new mlx5 driver, from Dan Carpenter.
11) Fix freed pointer reference in ipv6 multicast routing on namespace
cleanup, from Hannes Frederic Sowa.
12) Some usbnet drivers report TSO and SG in their feature set, but the
usbnet layer doesn't really support them. From Eric Dumazet.
13) Fix crash on EEH errors in tg3 driver, from Gavin Shan.
14) Drop cb_lock when requesting modules in genetlink, from Stanislaw
Gruszka.
15) Kernel stack leaks in cbq scheduler and af_key pfkey messages, from
Dan Carpenter.
16) FEC driver erroneously signals NETDEV_TX_BUSY on transmit leading to
endless loops, from Uwe Kleine-König.
17) Fix hangs from loading mvneta driver, from Arnaud Patard.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (84 commits)
mlx5: fix error return code in mlx5_alloc_uuars()
mvneta: Try to fix mvneta when compiled as module
mvneta: Fix hang when loading the mvneta driver
atl1c: Fix misuse of netdev_alloc_skb in refilling rx ring
genetlink: fix usage of NLM_F_EXCL or NLM_F_REPLACE
af_key: more info leaks in pfkey messages
net/fec: Don't let ndo_start_xmit return NETDEV_TX_BUSY without link
net_sched: Fix stack info leak in cbq_dump_wrr().
igb: fix vlan filtering in promisc mode when not in VT mode
ixgbe: Fix Tx Hang issue with lldpad on 82598EB
genetlink: release cb_lock before requesting additional module
net: fec: workaround stop tx during errata ERR006358
qlcnic: Fix diagnostic interrupt test for 83xx adapters.
qlcnic: Fix setting Guest VLAN
qlcnic: Fix operation type and command type.
qlcnic: Fix initialization of work function.
Revert "atl1c: Fix misuse of netdev_alloc_skb in refilling rx ring"
atl1c: Fix misuse of netdev_alloc_skb in refilling rx ring
net/tg3: Fix warning from pci_disable_device()
net/tg3: Fix kernel crash
...
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
- BMIPS SMP fixes
- a build fix necessary for older compilers
- two more bugs found my Chandras' testing
- and one more build fix
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: BMIPS: fix slave CPU booting when physical CPU is not 0
MIPS: BMIPS: do not change interrupt routing depending on boot CPU
MIPS: powertv: Fix arguments for free_reserved_area()
MIPS: Set default CPU type for BCM47XX platforms
MIPS: uapi/asm/siginfo.h: Fix GCC 4.1.2 compilation
MIPS: Fix multiple definitions of UNCAC_BASE.
Merge tag 'stable/for-linus-3.11-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen fixes from Konrad Rzeszutek Wilk:
- Three fixes for ARM/ARM64 to either compile or not certain generic
drivers
- Fix for avoiding a potential deadlock when an user space event
channel is destroyed.
- Fix a workqueue resuming multiple times.
* tag 'stable/for-linus-3.11-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/tmem: do not allow XEN_TMEM on ARM64
xen/evtchn: avoid a deadlock when unbinding an event channel
xen/arm: enable PV control for ARM
xen/arm64: Don't compile cpu hotplug
xenbus: frontend resume cleanup
Merge tag 'xen-arm-3.11-rc2-warn-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/sstabellini/xen
Pull Xen ARM fix from Stefano Stabellini.
Update xen_restart to new calling convention.
* tag 'xen-arm-3.11-rc2-warn-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/sstabellini/xen:
xen/arm,arm64: update xen_restart after ff701306cd49 and 7b6d864b48d9
Merge tag 'usb-3.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some tiny USB fixes for 3.11-rc4
Nothing major, some gadget fixes, some new device ids, a new tiny
driver for the ANT+ USB device, and a number of fixes for the mos7840
driver that were much needed"
* tag 'usb-3.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: serial: ftdi_sio: add more RT Systems ftdi devices
usb: chipidea: fix the build error with randconfig
usb: chipidea: cast PORTSC_PTS and DEVLC_PTS macros
usb: gadget: udc-core: fix the typo of udc state attribute
usb: gadget: f_phonet: remove unused preprocessor conditional
usb: gadget: multi: fix error return code in cdc_do_config()
USB: mos7840: fix pointer casts
USB: mos7840: fix race in led handling
USB: mos7840: fix device-type detection
USB: mos7840: fix race in register handling
USB: serial: add driver for Suunto ANT+ USB device
usb: gadget: free opts struct on error recovery
usb: gadget: ether: put_usb_function on unbind
usb: musb: fix resource passed from glue layer to musb
Merge tag 'tty-3.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are 4 tiny tty and serial driver fixes for 3.11-rc4.
Nothing big, a refcount leak, a module alias fix, and two fixes to the
mxs-auart serial driver"
* tag 'tty-3.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: arc_uart: Fix module alias
tty_port: Fix refcounting leak in tty_port_tty_hangup()
serial/mxs-auart: increase time to wait for transmitter to become idle
serial/mxs-auart: fix race condition in interrupt handler
When the mvneta driver is compiled as module, the clock is disabled before
it's loading. This will reset the registers values and all configuration
made by the bootloader.
This patch sets the "sgmii serdes configuration" register to a magical value
found in:
https://github.com/yellowback/ubuntu-precise-armadaxp/blob/master/arch/arm/mach-armadaxp/armada_xp_family/ctrlEnv/mvCtrlEnvLib.c
With this change, the interrupts are working/generated and ethernet is
working.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org> Signed-off-by: David S. Miller <davem@davemloft.net>
When the mvneta driver is compiled, it'll be loaded with clocks disabled.
This implies that the clocks should be enabled again before any register
access or it'll hang.
To fix it:
- enable clock earlier
- move timer callback after setting timer.data
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 29 Jul 2013 17:24:04 +0000 (10:24 -0700)]
atl1c: Fix misuse of netdev_alloc_skb in refilling rx ring
On Mon, 2013-07-29 at 08:30 -0700, Eric Dumazet wrote:
> On Mon, 2013-07-29 at 13:09 +0100, Luis Henriques wrote:
>
> >
> > I confirm that I can't reproduce the issue using this patch.
> >
>
> Thanks, I'll send a polished patch, as this one had an error if
> build_skb() returns NULL (in case sk_buff allocation fails)
Please try the following patch : It should use 2K frags instead of 4K
for normal 1500 mtu
Thanks !
[PATCH] atl1c: use custom skb allocator
We had reports ( https://bugzilla.kernel.org/show_bug.cgi?id=54021 )
that using high order pages for skb allocations is problematic for atl1c
We do not know exactly what the problem is, but we suspect that crossing
4K pages is not well supported by this hardware.
Use a custom allocator, using page allocator and 2K fragments for
optimal stack behavior. We might make this allocator generic
in future kernels.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Luis Henriques <luis.henriques@canonical.com> Cc: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira [Mon, 29 Jul 2013 10:30:04 +0000 (12:30 +0200)]
genetlink: fix usage of NLM_F_EXCL or NLM_F_REPLACE
Currently, it is not possible to use neither NLM_F_EXCL nor
NLM_F_REPLACE from genetlink. This is due to this checking in
genl_family_rcv_msg:
if (nlh->nlmsg_flags & NLM_F_DUMP)
NLM_F_DUMP is NLM_F_MATCH|NLM_F_ROOT. Thus, if NLM_F_EXCL or
NLM_F_REPLACE flag is set, genetlink believes that you're
requesting a dump and it calls the .dumpit callback.
The solution that I propose is to refine this checking to
make it stricter:
if ((nlh->nlmsg_flags & NLM_F_DUMP) == NLM_F_DUMP)
And given the combination NLM_F_REPLACE and NLM_F_EXCL does
not make sense to me, it removes the ambiguity.
There was a patch that tried to fix this some time ago (0ab03c2
netlink: test for all flags of the NLM_F_DUMP composite) but it
tried to resolve this ambiguity in *all* existing netlink subsystems,
not only genetlink. That patch was reverted since it broke iproute2,
which is using NLM_F_ROOT to request the dump of the routing cache.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Sun, 28 Jul 2013 20:04:45 +0000 (23:04 +0300)]
af_key: more info leaks in pfkey messages
This is inspired by a5cc68f3d6 "af_key: fix info leaks in notify
messages". There are some struct members which don't get initialized
and could disclose small amounts of private information.
Acked-by: Mathias Krause <minipli@googlemail.com> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/fec: Don't let ndo_start_xmit return NETDEV_TX_BUSY without link
Don't test for having link and let hardware deal with this situation.
Without this patch I see a machine running an -rt patched Linux being
stuck in sch_direct_xmit when it looses link while there is still a
packet to be sent. In this case the fec_enet_start_xmit routine returned
NETDEV_TX_BUSY which makes the network stack reschedule the packet and
so sch_direct_xmit calls fec_enet_start_xmit again.
I failed to reproduce a complete hang without -rt, but I think the
problem exists there, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
MIPS: BMIPS: fix slave CPU booting when physical CPU is not 0
The current BMIPS SMP code assumes that the slave CPU is physical and
logical CPU 1, but on some systems such as BCM3368, the slave CPU is
physical CPU0. Fix the code to read the physical CPU (thread ID) we are
running this code on, and adjust the relocation vector address based on
it. This allows bringing up the second CPU on BCM3368 for instance.
MIPS: BMIPS: do not change interrupt routing depending on boot CPU
Commit 4df715aa ("MIPS: BMIPS: support booting from physical CPU other
than 0") changed the interupt routing when we are booting from physical
CPU 0, but the settings are actually correct if we are booting from
physical CPU 0 or CPU 1. Revert that specific change.
merged in 3.11-rc1, broke the build for the powertv defconfig with
the following build error:
arch/mips/powertv/asic/asic_devices.c: In function 'platform_release_memory':
arch/mips/powertv/asic/asic_devices.c:533:7: error: passing argument 1 of
'free_reserved_area' makes pointer from integer without a cast [-Werror]
The free_reserved_area() function expects a void * pointer for the start
address and a void * pointer for the end one.
If neither BCM47XX_SSD nor BCM47XX_BCMA is selected, then no
CPU type is available leading to build problems. We fix
this problem by using MIPS32r1 as the default CPU type for
the BCM47XX platform.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com> Acked-by: Steven J. Hill <Steven.Hill@imgtec.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5618/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It wasn't until GCC 4.3 I believe that the __SIZEOF_*__ predefined macros
were added. The change below switches <uapi/asm/siginfo.h> to the
_MIPS_SZLONG macro so that compilation with e.g. GCC 4.1.2 succeeds.
This is a user API header so I think this is even more important, for
older userland support. The change adds an unsuccessful default too, to
catch any compiler configuration oddities.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5630/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Steven J. Hill [Wed, 3 Jul 2013 17:28:22 +0000 (17:28 +0000)]
MIPS: Fix multiple definitions of UNCAC_BASE.
Fix build error below:
arch/mips/include/asm/mach-generic/spaces.h:29:0: warning:
"UNCAC_BASE" redefined [enabled by default]
In file included from arch/mips/include/asm/addrspace.h:13:0,
from arch/mips/include/asm/barrier.h:11,
from arch/mips/include/asm/bitops.h:18,
from include/linux/bitops.h:22,
from include/linux/kernel.h:10,
from include/asm-generic/bug.h:13,
from arch/mips/include/asm/bug.h:41,
from include/linux/bug.h:4,
from include/linux/page-flags.h:9,
from kernel/bounds.c:9:
arch/mips/include/asm/mach-ar7/spaces.h:20:0: note: this is the
location of the previous definition
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5583/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Vrabel [Fri, 19 Jul 2013 14:51:58 +0000 (15:51 +0100)]
xen/evtchn: avoid a deadlock when unbinding an event channel
Unbinding an event channel (either with the ioctl or when the evtchn
device is closed) may deadlock because disable_irq() is called with
port_user_lock held which is also locked by the interrupt handler.
Think of the IOCTL_EVTCHN_UNBIND is being serviced, the routine has
just taken the lock, and an interrupt happens. The evtchn_interrupt
is invoked, tries to take the lock and spins forever.
A quick glance at the code shows that the spinlock is a local IRQ
variant. Unfortunately that does not help as "disable_irq() waits for
the interrupt handler on all CPUs to stop running. If the irq occurs
on another VCPU, it tries to take port_user_lock and can't because
the unbind ioctl is holding it." (from David). Hence we cannot
depend on the said spinlock to protect us. We could make it a system
wide IRQ disable spinlock but there is a better way.
We can piggyback on the fact that the existence of the spinlock is
to make get_port_user() checks be up-to-date. And we can alter those
checks to not depend on the spin lock (as it's protected by u->bind_mutex
in the ioctl) and can remove the unnecessary locking (this is
IOCTL_EVTCHN_UNBIND) path.
In the interrupt handler we cannot use the mutex, but we do not
need it.
"The unbind disables the irq before making the port user stale, so when
you clear it you are guaranteed that the interrupt handler that might
use that port cannot be running." (from David).
Hence this patch removes the spinlock usage on the teardown path
and piggybacks on disable_irq happening before we muck with the
get_port_user() data. This ensures that the interrupt handler will
never run on stale data.
Signed-off-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
[v1: Expanded the commit description a bit]
Merge tag 'firewire-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull firewire regression fix from Stefan Richter:
"This fixes corrupted video capture, seen with IIDC/DCAM video and
certain buffer settings. (Regression since v3.4 inclusive.)"
* tag 'firewire-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: fix libdc1394/FlyCap2 iso event regression
USB: serial: ftdi_sio: add more RT Systems ftdi devices
RT Systems makes many usb serial cables based on the ftdi_sio driver for
programming various amateur radios. This patch is a full listing of
their current product offerings and should allow these cables to all
be recognized.
usb: chipidea: cast PORTSC_PTS and DEVLC_PTS macros
Fix the following build warnings on x86:
drivers/usb/chipidea/core.c: In function 'hw_phymode_configure':
drivers/usb/chipidea/core.c:226:3: warning: large integer implicitly truncated to unsigned type [-Woverflow]
drivers/usb/chipidea/core.c:230:3: warning: large integer implicitly truncated to unsigned type [-Woverflow]
drivers/usb/chipidea/core.c:243:3: warning: large integer implicitly truncated to unsigned type [-Woverflow]
drivers/usb/chipidea/core.c:246:3: warning: large integer implicitly truncated to unsigned type [-Woverflow]
Reported-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge tag 'fixes-for-v3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v3.11-rc3
Here are some fixes for v3.11-rc3. Mostly related to
the recent conversion to configfs done on the gadget
drivers, but we also have a fix for MUSB resources
on platforms which need 3 resources instead of 2, and
a fix for the sysfs_notify() call on udc-core.c which
was notifying an unexistent file.
Rong Wang [Sun, 28 Jul 2013 15:01:35 +0000 (23:01 +0800)]
usb: gadget: udc-core: fix the typo of udc state attribute
The name of udc state attribute file under sysfs is registered as
"state", while usb_gadget_set_state take it as "status" when it's
going to update. This patch fixes the typo.
Signed-off-by: Rong Wang <Rong.Wang@csr.com> Signed-off-by: Barry Song <Baohua.Song@csr.com> Cc: <stable@kernel.org> Signed-off-by: Felipe Balbi <balbi@ti.com>
The compatibility layer which the USBF_PHONET_INCLUDED was a part of
is no longer present - the USBF_PHONET_INCLUDED is not #defined by anyone
anymore, so the ifndef is always true. Removing it.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: multi: fix error return code in cdc_do_config()
Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.
Introduced by commit 59835a (usb: gadget: multi: use
function framework for ACM.)
Make rndis_do_config() consistent with cdc_do_config() in the way it
handles returning the PTR_ERR(f_acm_*).
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Merge tag 'pinctrl-for-v3.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
- Driver fixes for AM33xx, SIRF and PFC pin controllers
- Fix a compile warning from the pinctrl single-register driver
- Fix a little nasty memory leak
* tag 'pinctrl-for-v3.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: fix a memleak when freeing maps
pinctrl: pinctrl-single: fix compile warning when no CONFIG_PM
pinctrl: sh-pfc: fix SDHI0 VccQ regulator on sh73a0 with DT
arm/dts: sirf: fix the pingroup name mismatch between drivers and dts
pinctrl: sirf: add usp0_uart_nostreamctrl pin group for usp-uart without flowctrl
pinctrl: sirf: fix the pin number and mux bit for usp0
pinctrl: am33xx dt binding: correct include path
Merge tag 'trace-fixes-3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Oleg is working on fixing a very tight race between opening a event
file and deleting that event at the same time (both must be done as
root).
I also found a bug while testing Oleg's patches which has to do with a
race with kprobes using the function tracer.
There's also a deadlock fix that was introduced with the previous
fixes"
* tag 'trace-fixes-3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Remove locking trace_types_lock from tracing_reset_all_online_cpus()
ftrace: Add check for NULL regs if ops has SAVE_REGS set
tracing: Kill trace_cpu struct/members
tracing: Change tracing_fops/snapshot_fops to rely on tracing_get_cpu()
tracing: Change tracing_entries_fops to rely on tracing_get_cpu()
tracing: Change tracing_stats_fops to rely on tracing_get_cpu()
tracing: Change tracing_buffers_fops to rely on tracing_get_cpu()
tracing: Change tracing_pipe_fops() to rely on tracing_get_cpu()
tracing: Introduce trace_create_cpu_file() and tracing_get_cpu()
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is five bug fixes, two of which fix long standing problems
causing crashes (sd and mvsas). The remaining three are hung (isci
race) or lost (qla2xxx, isci) devices"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] isci: fix breakage caused by >16byte CDB patch
[SCSI] mvsas: Fix kernel panic on tile due to unaligned data access
[SCSI] sd: fix crash when UA received on DIF enabled device
[SCSI] qla2xxx: Properly set the tagging for commands.
[SCSI] isci: Fix a race condition in the SSP task management path
Emil Tantilov [Fri, 26 Jul 2013 12:46:36 +0000 (05:46 -0700)]
igb: fix vlan filtering in promisc mode when not in VT mode
This patch fixes a VT mode check to make sure VLAN filters are disabled when
in promisc mode and VT is not enabled.
The problem with the previous check was that:
E1000_MRQC_ENABLE_VMDQ is defined as 0x00000003
but when not in VT mode:
mrqc |= E1000_MRQC_ENABLE_RSS_4Q (0x00000002)
So the above check will trigger regardless if VT mode is being used or not.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an issue with the 82598EB device, where lldpad is causing Tx
Hangs on the card as soon as it attempts to configure DCB for the device. The
adapter will continually Tx hang and reset in a loop.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Cc: Stable <stable@vger.kernel.org> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Tested-by: Jack Morgan <jack.morgan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hovold [Sat, 27 Jul 2013 11:34:42 +0000 (13:34 +0200)]
USB: mos7840: fix pointer casts
Silence compiler warnings on 64-bit systems introduced by commit 05cf0dec ("USB: mos7840: fix race in led handling") which uses the
usb-serial data pointer to temporarily store the device type during
probe but failed to add the required casts.
[gregkh - change uintptr_t to unsigned long]
Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
genetlink: release cb_lock before requesting additional module
Requesting external module with cb_lock taken can result in
the deadlock like showed below:
[ 2458.111347] Showing all locks held in the system:
[ 2458.111347] 1 lock held by NetworkManager/582:
[ 2458.111347] #0: (cb_lock){++++++}, at: [<ffffffff8162bc79>] genl_rcv+0x19/0x40
[ 2458.111347] 1 lock held by modprobe/603:
[ 2458.111347] #0: (cb_lock){++++++}, at: [<ffffffff8162baa5>] genl_lock_all+0x15/0x30
Problem start to happen after adding net-pf-16-proto-16-family-nl80211
alias name to cfg80211 module by below commit (though that commit
itself is perfectly fine):
nl80211: Add generic netlink module alias for cfg80211/nl80211
Reported-and-tested-by: Jeff Layton <jlayton@redhat.com> Reported-by: Richard W.M. Jones <rjones@redhat.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Reviewed-by: Pravin B Shelar <pshelar@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Frank Li [Thu, 25 Jul 2013 06:05:53 +0000 (14:05 +0800)]
net: fec: workaround stop tx during errata ERR006358
If the ready bit in the transmit buffer descriptor (TxBD[R])
is previously detected as not set during a prior frame transmission,
then the ENET_TDAR[TDAR] bit is cleared at a later time, even if
additional TxBDs were added to the ring and the ENET_TDAR[TDAR]
bit is set. This results in frames not being transmitted until
there is a 0-to-1 transition on ENET_TDAR[TDAR].
Workarounds:
code can use the transmit frame interrupt flag (ENET_EIR[TXF])
as a method to detect whether the ENET has completed transmission
and the ENET_TDAR[TDAR] has been cleared. If ENET_TDAR[TDAR] is
detected as cleared when packets are queued and waiting for transmit,
then a write to the TDAR bit will restart TxBD processing.
This case main happen when loading is light. A ethernet package may
not send out utile next package put into tx queue.
How to test:
while [ true ]
do
ping <IP> -s 10000 -w 4
ping <IP> -s 6000 -w 2
ping <IP> -s 4000 -w 2
ping <IP> -s 10000 -w 2
done
You will see below result in overnight test.
6008 bytes from 10.192.242.116: seq=1 ttl=128 time=0.722 ms
4008 bytes from 10.192.242.116: seq=0 ttl=128 time=1001.008 ms
4008 bytes from 10.192.242.116: seq=1 ttl=128 time=1.010 ms
10008 bytes from 10.192.242.116: seq=0 ttl=128 time=0.896 ms
After apply this patch, >1000ms delay disappear.
Signed-off-by: Frank Li <Frank.Li@freescale.com> Acked-by: Fugang Duan <B38611@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
qlcnic: Fix diagnostic interrupt test for 83xx adapters.
o Initialize proper interrupt handler for 83xx.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
o When configuring guest VLAN after PVID configuration, VF was loading
with previously configured PVID. Clear the PVID which was previously
configured before configuring guest VLAN.
o Display guest VLAN when it is configured
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Operation type and command type is not set correct in back channel
response.
Signed-off-by: Pratik Pujar <pratik.pujar@qlogic.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Work function needs to be initialized before we participate in
inter device communication (IDC).
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Clemens Ladisch [Mon, 22 Jul 2013 19:32:09 +0000 (21:32 +0200)]
firewire: fix libdc1394/FlyCap2 iso event regression
Commit 18d627113b83 (firewire: prevent dropping of completed iso packet
header data) was intended to be an obvious bug fix, but libdc1394 and
FlyCap2 depend on the old behaviour by ignoring all returned information
and thus not noticing that not all packets have been received yet. The
result was that the video frame buffers would be saved before they
contained the correct data.
Reintroduce the old behaviour for old clients.
Tested-by: Stepan Salenikovich <stepan.salenikovich@gmail.com> Tested-by: Josep Bosch <jep250@gmail.com> Cc: <stable@vger.kernel.org> # 3.4+ Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Uwe Kleine-König [Fri, 28 Jun 2013 09:49:41 +0000 (11:49 +0200)]
serial/mxs-auart: increase time to wait for transmitter to become idle
Without this patch the driver waits ~1 ms for the UART to become idle. At
115200n8 this time is (theoretically) enough to transfer 11.5 characters
(= 115200 bits/s / (10 Bits/char) * 1ms). As the mxs-auart has a fifo size
of 16 characters the clock is gated too early. The problem is worse for
lower baud rates.
This only happens to really shut down the transmitter in the middle of a
transfer if /dev/ttyAPPx isn't opened in userspace (e.g. by a getty) but
was at least once (because the bootloader doesn't disable the transmitter).
So increase the timeout to 20 ms which should be enough for 9600n8, too.
Moreover skip gating the clock if the timeout is elapsed.
serial/mxs-auart: fix race condition in interrupt handler
The handler needs to ack the pending events before actually handling them.
Otherwise a new event might come in after it it considered non-pending or
handled and is acked then without being handled. So this event is only
noticed when the next interrupt happens.
Without this patch an i.MX28 based machine running an rt-patched kernel
regularly hangs during boot.
Neil Horman [Fri, 26 Jul 2013 16:47:14 +0000 (12:47 -0400)]
atl1c: Fix misuse of netdev_alloc_skb in refilling rx ring
atl1c uses netdev_alloc_skb to refill its rx dma ring, but that call makes no
guarantees about the suitability of the memory for use in DMA. As a result
we've gotten reports of atl1c drivers occasionally hanging and needing to be
reset:
https://bugzilla.kernel.org/show_bug.cgi?id=54021
Fix this by modifying the call to use the internal version __netdev_alloc_skb,
where you can set the gfp_mask explicitly to include GFP_DMA.
Tested by two reporters in the above bug, who have the hardware to validate it.
Both report immediate cessation of the problem with this patch
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> CC: Jay Cliburn <jcliburn@gmail.com> CC: "David S. Miller" <davem@davemloft.net> CC: stable@vger.kernel.org Tested-by: Luis Henriques <luis.henriques@canonical.com> Tested-by: Vincent Alquier <vincent.alquier@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"This is just a regular fixes pull apart from the qxl one, it has
radeon and intel bits in it,
The intel fixes are for a regression with the RC6 fix and a 3.10 hdmi
regression, whereas radeon is more DPM fixes, a few lockup fixes and
some rn50/r100 DAC fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/dpm: fix r600_enable_sclk_control()
drm/radeon/dpm: implement force performance levels for rv6xx
drm/radeon/dpm: fix displaygap programming on rv6xx
drm/radeon/dpm: fix a typo in the rv6xx mclk setup
drm/i915: initialize gt_lock early with other spin locks
drm/i915: fix hdmi portclock limits
drm/radeon: fix combios tables on older cards
drm/radeon: improve dac adjust heuristics for legacy pdac
drm/radeon: Another card with wrong primary dac adj
drm/radeon: fix endian issues with DP handling (v3)
drm/radeon/vm: only align the pt base to 32k
drm/radeon: wait for 3D idle before using CP DMA
Merge branch 'qxl-fixes' of git://people.freedesktop.org/~airlied/linux
Pull qxl drm fixes from Dave Airlie:
"Okay as I warned, the qxl driver was running a bit free and loose with
its ttm object reservations and the new lockdep enabled reservation
tracking shone a bright light into it, it also with the new
reservations mutexes hits a possible deadlock during boot.
The first patch is a real fix to render the console correctly as the
driver used to just drop irq renderering as too hard, this also fixes
a sleeping while atomic warning.
The other two patches are the big ugly ones that redo how the driver
allocates objects and reserves them and makes things all work
properly, I've tested this in a VM, and compared to the current code
which hits a lockdep warning and the sleep while atomic warning before
failing.
So sorry this is coming in late, I should have tested qxl before
merging the mutex code, but I'd rather just fix qxl with this than
revert the reservations code at this point"
* 'qxl-fixes' of git://people.freedesktop.org/~airlied/linux:
qxl: convert qxl driver to proper use for reservations
qxl: allow creation of pre-pinned objects and use for releases.
drm/qxl: add delayed fb operations
Merge tag 'pm+acpi-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These are just two fixes, a revert of the would-be backlight fix that
didn't work and an intel_pstate fix for two problems related to
maximum P-state selection.
Specifics:
- Revert of the ACPI video commit that I hoped would help fix
backlight problems related to Windows 8 compatibility on some
systems. Unfortunately, it turned out to cause problems to happen
too.
- Fix for two problems in intel_pstate, a possible failure to respond
to a load change on a quiet system and a possible failure to select
the highest available P-state on some systems. From Dirk
Brandewie"
* tag 'pm+acpi-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "ACPI / video / i915: No ACPI backlight if firmware expects Windows 8"
cpufreq / intel_pstate: Change to scale off of max P-state
Reported-by: Wei Yang <weiyang@linux.vnet.ibm.com> Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com> Acked-by: Nithin Nayak Sujir <nsujir@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
While EEH error happens, we might not have network device instance
(struct net_device) yet. So we can't access the instance safely and
check its link state, which causes kernel crash. The patch fixes it.
Reported-by: Wei Yang <weiyang@linux.vnet.ibm.com> Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com> Acked-by: Nithin Nayak Sujir <nsujir@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Francesco Fusco [Wed, 24 Jul 2013 08:39:07 +0000 (10:39 +0200)]
sysctl: range checking in do_proc_dointvec_ms_jiffies_conv
When (integer) sysctl values are expressed in ms and have to be
represented internally as jiffies. The msecs_to_jiffies function
returns an unsigned long, which gets assigned to the integer.
This patch prevents the value to be assigned if bigger than
INT_MAX, done in a similar way as in cba9f3 ("Range checking in
do_proc_dointvec_(userhz_)jiffies_conv").
Signed-off-by: Francesco Fusco <ffusco@redhat.com> CC: Andrew Morton <akpm@linux-foundation.org> CC: linux-kernel@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
Francesco Fusco [Wed, 24 Jul 2013 08:39:06 +0000 (10:39 +0200)]
neigh: prevent overflowing params in /proc/sys/net/ipv4/neigh/
Without this patch, the fields app_solicit, gc_thresh1, gc_thresh2,
gc_thresh3, proxy_qlen, ucast_solicit, mcast_solicit could have
assumed negative values when setting large numbers.
Signed-off-by: Francesco Fusco <ffusco@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hovold [Fri, 26 Jul 2013 09:55:19 +0000 (11:55 +0200)]
USB: mos7840: fix race in led handling
Fix race in LED handling introduced by commit 0eafe4de ("USB: serial:
mos7840: add support for MCS7810 devices") which reused the port control
urb for manipulating the LED without making sure that the urb is not
already in use. This could lead to the control urb being manipulated
while in flight.
Fix by adding a dedicated LED urb and ctrlrequest along with a LED-busy
flag to handle concurrency.
Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Fri, 26 Jul 2013 09:55:18 +0000 (11:55 +0200)]
USB: mos7840: fix device-type detection
Fix race in device-type detection introduced by commit 0eafe4de ("USB:
serial: mos7840: add support for MCS7810 devices") which used a static
variable to hold the device type.
Move type detection to probe and use serial data to store the device
type.
Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: serial: add driver for Suunto ANT+ USB device
This adds a driver for the Suunto ANT+ USB device, exposing it as a usb
serial device. This lets the userspace "gant" program to talk to the
device to communicate over the ANT+ protocol to any devices it finds.
Eric Dumazet [Wed, 24 Jul 2013 00:15:54 +0000 (17:15 -0700)]
usbnet: do not pretend to support SG/TSO
usbnet doesn't support yet SG, so drivers should not advertise SG or TSO
capabilities, as they allow TCP stack to build large TSO packets that
need to be linearized and might use order-5 pages.
This adds an extra copy overhead and possible allocation failures.
Current code ignore skb_linearize() return code so crashes are even
possible.
Best is to not pretend SG/TSO is supported, and add this again when/if
usbnet really supports SG for devices who could get a performance gain.
Based on a prior patch from Freddy Xin <freddy@asix.com.tw>
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge tag 'arm64-stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64
Pull arm64 fixes from Catalin Marinas:
- Stack size increased to 16K (similar to other 64-bit architectures)
- Additional cache flushing for secondary CPUs boot mode
* tag 'arm64-stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
arm64: Change kernel stack size to 16K
arm64: Fix definition of arm_pm_restart to match the declaration
arm64: virt: ensure visibility of __boot_cpu_mode
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"This is a largeish batch of fixes, mostly because I missed -rc2 due to
travel/vacation. So in number these are a bit more than ideal unless
you amortize them over two -rcs.
Quick breakdown:
- Defconfig updates
- Making multi_v7_defconfig useful on more hardware to encourage
single-image usage
- Davinci and nomadik updates due to new code merged this merge
window
- Fixes for UART on Samsung platforms, both PM and clock-related
- A handful of warning fixes from defconfig builds, including for
max8925 backlight and pxamci (both with appropriate acks)
- Exynos5440 fixes for LPAE configuration, PM
- ...plus a bunch of other smaller changes all over the place
I expect to switch to regressions-or-severe-bugs-only fixes from here
on out"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (37 commits)
mfd: max8925: fix dt code for backlight
ARM: omap5: Only select errata 798181 if SMP
ARM: EXYNOS: Update CONFIG_ARCH_NR_GPIO for Exynos
ARM: EXYNOS: Fix low level debug support
ARM: SAMSUNG: Save/restore only selected uart's registers
ARM: SAMSUNG: Add SAMSUNG_PM config option to select pm
ARM: S3C24XX: Add missing clkdev entries for s3c2440 UART
ARM: multi_v7_defconfig: Select USB chipidea driver
ARM: pxa: propagate errors from regulator_enable() to pxamci
ARM: zynq: fix compilation warning
ARM: keystone: fix compilation warning
ARM: highbank: Only touch common coherency control register fields
ARM: footbridge: fix overlapping PCI mappings
dmaengine: shdma: fix a build failure on platforms with no DMA support
ARM: STi: Set correct ARM ERRATAs.
ARM: dts: STi: Fix pinconf setup for STiH416 serial2
ARM: nomadik: configure for NO_HZ and HRTIMERS
ARM: nomadik: update defconfig base
ARM: nomadik: Update MMC defconfigs
ARM: davinci: defconfig: enable EDMA driver
...
Merge tag 'usb-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of USB fixes for 3.11-rc3.
Lots of little things, nothing major. A number of new device ids,
build fixes for DMA, and a bunch of other minor things. All of these
have been in the linux-next tree"
* tag 'usb-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (40 commits)
usb: Clear both buffers when clearing a control transfer TT buffer.
usb/gadget: free opts struct on error recovery
USB: mos7840: fix memory leak in open
usb: serial: option.c: remove ONDA MT825UP product ID fromdriver
usb: serial: option: add Olivetti Olicard 200
usb: serial: option: blacklist ONDA MT689DC QMI interface
xhci: fix null pointer dereference on ring_doorbell_for_active_rings
usb: host: xhci: Enable XHCI_SPURIOUS_SUCCESS for all controllers with xhci 1.0
usb: fix build warning in pci-quirks.h when CONFIG_PCI is not enabled
usb: xhci: Mark two functions __maybe_unused
xhci: Avoid NULL pointer deref when host dies.
usb: serial: option: Add ONYX 3G device support
USB: ti_usb_3410_5052: fix dynamic-id matching
usb: option: add TP-LINK MA260
USB: option: add D-Link DWM-152/C1 and DWM-156/C1
USB: EHCI: Fix resume signalling on remote wakeup
USB: cp210x: add MMB and PI ZigBee USB Device Support
usb: cp210x support SEL C662 Vendor/Device
USB: option: append Petatel NP10T device to GSM modems list
USB: misc: Add Manhattan Hi-Speed USB DVI Converter to sisusbvga
...
Merge tag 'tty-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are 3 fixes for TTY and serial issues that have been reported.
Nothing huge, but nice to get fixed"
* tag 'tty-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: tegra: correct help message in Kconfig from 'ttyHS' to 'ttyTHS'
tty/8250_early: Don't truncate last character of options
TTY: snyclinkmp: calculating wrong addresses
Merge tag 'staging-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging fixes from Greg KH:
"Here are some tiny drivers/staging/ fixes for 3.11-rc3
A number of bugfixes, all pretty tiny, but resolve issues that have
been reported (the kstrtos32 change fixes a data corruption problem
that Dan found). And a MAINTAINERS file update for the comedi
drivers"
* tag 'staging-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
MAINTAINERS: Update the list of maintainers for staging/comedi driver.
staging: tidspbridge: replace strict_strtol() with kstrtos32()
staging: android: logger: Correct write offset reset on error
staging: zram: protect zram_reset_device() call
staging: gdm72xx: potential use after free in send_qos_list()
staging: drm/imx: drop "select OF_VIDEOMODE"
staging: frontier: use after free in disconnect()
staging: comedi: fix a race between do_cmd_ioctl() and read/write
staging: comedi: COMEDI_CANCEL ioctl should wake up read/write
Merge tag 'char-misc-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc patches from Greg KH:
"Here are some char/misc patches for 3.11-rc3. It's pretty much just:
- mei fixes
- hyperv fixes
- new ja_JP translation update
all tiny stuff, but fixes for issues people have reported."
* tag 'char-misc-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
HOWTO ja_JP sync
mei: me: fix waiting for hw ready
mei: don't have to clean the state on power up
mei: me: fix reset state machine
mei: hbm: fix typo in error message
Tools: hv: KVP: Fix a bug in IPV6 subnet enumeration
Drivers: hv: balloon: Do not post pressure status if interrupted
Drivers: hv: balloon: Fix a bug in the hot-add code
Drivers: hv: vmbus: incorrect device name is printed when child device is unregistered
Merge tag 'sound-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Just a handful of regression and small fixes in ASoC, HD-audio and
USB-audio drivers.
- Sigmetal HD-audio codec regression fixes
- A copule of XRUN indication fixes for usb-audio devices
- ASoC: ep93xx build fix, sgtl5000 fix for probe order changes,
max98088 register access fix, etc"
* tag 'sound-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hiface: return correct XRUN indication
ASoC: tegra: correct playback_dma_data setup
ASoC: core: double free in snd_soc_add_platform()
ALSA: usb-audio: 6fire: return correct XRUN indication
ASoC: ep93xx: fix build of ep93xx-ac97.c
ALSA: hda - Remove NO_PRESENCE bit override for Dell 1420n Laptop
ALSA: hda - Fix EAPD GPIO control for Sigmatel codecs
ASoC: atmel-ssc: remove clk_disable_unprepare call from critical section
ASoC: sgtl5000: defer the probe if clock is not found
ASoC: max98088 - fix element type of the register cache.
Merge tag 'for-linus-v3.11-rc3' of git://oss.sgi.com/xfs/xfs
Pull xfs fix from Ben Myers:
"Fix for regression in commit cca9f93a52d2 ("xfs: don't do IO when
creating an new inode"), recovery causing filesystem corruption after
a crash"
* tag 'for-linus-v3.11-rc3' of git://oss.sgi.com/xfs/xfs:
xfs: di_flushiter considered harmful
Merge branch 'for-3.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"Assorted libata updates.
The most critical one is a fix for ahci oops during boot. Also, a new
smallish platform ahci driver is added and sata_inic162x is marked
clearly as experimental (it whines during boot too) as data corruption
seems rather common on the device and it's unlikely to get any love in
the foreseeable future. If the whining doesn't draw any attention, I
think we'd probably be better of making the driver depend on BROKEN in
a couple releases"
This is v2 of this pull request with fixed dependencies for ahci_imx.
* 'for-3.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci_imx: depend on CONFIG_MFD_SYSCON
ahci_imx: add ahci sata support on imx platforms
ARM: imx6q: update the sata bits definitions of gpr13
ahci: fix Null pointer dereference in achi_host_active()
libata: make it clear that sata_inic162x is experimental
libata: replace strict_strtol() with kstrtol()
ata: Fix DVD not dectected at some platform with Wellsburg PCH
Revert "ACPI / video / i915: No ACPI backlight if firmware expects Windows 8"
We attempted to address a regression introduced by commit a57f7f9
(ACPICA: Add Windows8/Server2012 string for _OSI method.) after which
ACPI video backlight support doesn't work on a number of systems,
because the relevant AML methods in the ACPI tables in their BIOSes
become useless after the BIOS has been told that the OS is compatible
with Windows 8. That problem is tracked by the bug entry at:
https://bugzilla.kernel.org/show_bug.cgi?id=51231
Commit 8c5bd7a (ACPI / video / i915: No ACPI backlight if firmware
expects Windows 8) introduced for this purpose essentially prevented
the ACPI backlight support from being used if the BIOS had been told
that the OS was compatible with Windows 8 and the i915 driver was
loaded, in which case the backlight would always be handled by i915.
Unfortunately, however, that turned out to cause problems with
backlight to appear on multiple systems with symptoms indicating that
i915 was unable to control the backlight on those systems as
expected.
For this reason, revert commit 8c5bd7a, but leave the function
acpi_video_backlight_quirks() introduced by it, because another
commit on top of it uses that function.
References: https://lkml.org/lkml/2013/7/21/119
References: https://lkml.org/lkml/2013/7/22/261
References: https://lkml.org/lkml/2013/7/23/429
References: https://lkml.org/lkml/2013/7/23/459
References: https://lkml.org/lkml/2013/7/23/81
References: https://lkml.org/lkml/2013/7/24/27 Reported-and-tested-by: James Hogan <james@albanarts.com> Reported-and-tested-by: Kamal Mostafa <kamal@canonical.com> Reported-and-tested-by: Jörg Otte <jrg.otte@gmail.com> Reported-and-tested-by: Steven Newbury <steve@snewbury.org.uk> Reported-by: Martin Steigerwald <Martin@lichtvoll.de> Reported-by: Kalle Valo <kvalo@adurom.com> Tested-by: Joerg Platte <jplatte@naasa.net> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ahci_imx makes use of regmap but the dependency wasn't specified in
Kconfig leading build failures if CONFIG_AHCI_IMX is enabled but
CONFIG_MFD_SYSCON is not. Add the Kconfig dependency.
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
tracing: Remove locking trace_types_lock from tracing_reset_all_online_cpus()
Commit a82274151af "tracing: Protect ftrace_trace_arrays list in trace_events.c"
added taking the trace_types_lock mutex in trace_events.c as there were
several locations that needed it for protection. Unfortunately, it also
encapsulated a call to tracing_reset_all_online_cpus() which also takes
the trace_types_lock, causing a deadlock.
This happens when a module has tracepoints and has been traced. When the
module is removed, the trace events module notifier will grab the
trace_types_lock, do a bunch of clean ups, and also clears the buffer
by calling tracing_reset_all_online_cpus. This doesn't happen often
which explains why it wasn't caught right away.
Commit a82274151af was marked for stable, which means this must be
sent to stable too.
Link: http://lkml.kernel.org/r/51EEC646.7070306@broadcom.com Reported-by: Arend van Spril <arend@broadcom.com> Tested-by: Arend van Spriel <arend@broadcom.com> Cc: Alexander Z Lam <azl@google.com> Cc: Vaibhav Nagarnaik <vnagarnaik@google.com> Cc: David Sharp <dhsharp@google.com> Cc: stable@vger.kernel.org # 3.10 Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Dave Airlie [Fri, 26 Jul 2013 10:38:14 +0000 (20:38 +1000)]
Merge tag 'drm-intel-fixes-2013-07-25' of git://people.freedesktop.org/~danvet/drm-intel into drm-fixes
Brown-paper-bag pull request here. The snb rc6 fix from the last pull
broke forcewake BIOS dirt cleanup, which with fixed. But that fix broke
the spinlock init sequence, which results in an ugly BUG when spinlock
debugging is enabled :( So I get to throw another patch at cc: stable to
fix up the mess ...
* tag 'drm-intel-fixes-2013-07-25' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: initialize gt_lock early with other spin locks
drm/i915: fix hdmi portclock limits
Dave Airlie [Fri, 26 Jul 2013 10:37:15 +0000 (20:37 +1000)]
Merge branch 'drm-fixes-3.11' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
r600 dpm fixes, old school card dac fixes, lockup fixes
endian fixes
* 'drm-fixes-3.11' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon/dpm: fix r600_enable_sclk_control()
drm/radeon/dpm: implement force performance levels for rv6xx
drm/radeon/dpm: fix displaygap programming on rv6xx
drm/radeon/dpm: fix a typo in the rv6xx mclk setup
drm/radeon: fix combios tables on older cards
drm/radeon: improve dac adjust heuristics for legacy pdac
drm/radeon: Another card with wrong primary dac adj
drm/radeon: fix endian issues with DP handling (v3)
drm/radeon/vm: only align the pt base to 32k
drm/radeon: wait for 3D idle before using CP DMA
Olof Johansson [Wed, 24 Jul 2013 15:42:27 +0000 (08:42 -0700)]
mfd: max8925: fix dt code for backlight
The device-tree enablement for max8925 has several problems, but besides
the bindings being wrong (and not having seen review) there's also some
bad coding practices on how to fill in the platform_data from device tree.
I came across this since it causes a warning when compiling
mmp2_defconfig, and instead of doing the minimal fix to silence the
warning, I restructured the code a bit.
This silences the warning:
drivers/video/backlight/max8925_bl.c: In function 'max8925_backlight_probe':
drivers/video/backlight/max8925_bl.c:177:3: warning: statement with no effect [-Wunused-value]
Note that the bindings themselves need to be revisited too, but that will
affect more than just the backlight driver and is best done separately;
this just fixes the bad code for the backlight driver.
Acked-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Olof Johansson <olof@lixom.net>
William Gulland [Thu, 27 Jun 2013 23:10:20 +0000 (16:10 -0700)]
usb: Clear both buffers when clearing a control transfer TT buffer.
Control transfers have both IN and OUT (or SETUP) packets, so when
clearing TT buffers for a control transfer it's necessary to send
two HUB_CLEAR_TT_BUFFER requests to the hub.
Signed-off-by: William Gulland <wgulland@google.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: serial: option.c: remove ONDA MT825UP product ID fromdriver
Some (very few) early devices like mine, where not exposting a proper CDC
descriptor. This was fixed with an immediate firmware update from the vendor,
and pre-installed on newer devices.
So actual devices can be driven by cdc_acm.c + cdc_ether.c.
projects / mirror_ubuntu-jammy-kernel.git / log