Plantronics BT300 does not support reading the sample rate which leads
to many lines of "cannot get freq at ep 0x1". This patch adds the USB
ID of the BT300 to quirks.c and avoids those error messages.
Signed-off-by: Dennis Kadioglu <denk@post.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Phoenix Audio TMX320 gives the similar error when the sample rate is
asked:
usb 2-1.3: 2:1: cannot get freq at ep 0x85
usb 2-1.3: 1:1: cannot get freq at ep 0x2
....
Add the corresponding USB-device ID (1de7:0014) to
snd_usb_get_sample_rate_quirk() list.
HP EliteBook 755 G2 with ALC3228 (ALC280) codec [103c:221c] requires
the known fixup (ALC269_FIXUP_HEADSET_MIC) for making the headset mic
working. Also, it suffers from the loopback noise problem, so we
should disable aamix path as well.
On one of the machines we enable, we found that the actual speaker volume
did not always correspond to the volume set in alsamixer. This patch
fixes that problem.
This patch was orginally written by Kailang @ Realtek, I've rebased it
to fit sound git master.
Add support and PCI IDs for more Broxton host controllers
Other BXT IDs were added in v4.4 so cc'ing stable. This patch
is dependent on commit 163cbe31e516 ("mmc: sdhci-pci: Fix card
detect race for Intel BXT/APL") but that is already in stable
since v4.4.4.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Because event_sched_out() checks event->pending_disable _before_
actually disabling the event, it can happen that the event fires after
it checks but before it gets disabled.
This would leave event->pending_disable set and the queued irq_work
will try and process it.
However, if the event trigger was during schedule(), the event might
have been de-scheduled by the time the irq_work runs, and
perf_event_disable_local() will fail.
Fix this by checking event->pending_disable _after_ we call
event->pmu->del(). This depends on the latter being a compiler
barrier, such that the compiler does not lift the load and re-creates
the problem.
Tested-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: dvyukov@google.com Cc: eranian@google.com Cc: oleg@redhat.com Cc: panand@redhat.com Cc: sasha.levin@oracle.com Cc: vince@deater.net Link: http://lkml.kernel.org/r/20160224174948.040469884@infradead.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
BUG: sleeping function called from invalid context at kernel/locking/rtmutex.c:917
in_atomic(): 1, irqs_disabled(): 128, pid: 383, name: sh
Preemption disabled at:[<ffff800000124c18>] kgdb_cpu_enter+0x158/0x6b8
This issue is similar with 62c6c61("arm64: replace read_lock to rcu lock in
call_break_hook"), but comes to single_step_handler.
This also solves kgdbts boot test silent hang issue on 4.4 -rt kernel.
Signed-off-by: Yang Shi <yang.shi@linaro.org> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
If we rename an inode A (be it a file or a directory), create a new
inode B with the old name of inode A and under the same parent directory,
fsync inode B and then power fail, at log tree replay time we end up
removing inode A completely. If inode A is a directory then all its files
are gone too.
Example scenarios where this happens:
This is reproducible with the following steps, taken from a couple of
test cases written for fstests which are going to be submitted upstream
soon:
The next time the fs is mounted, log tree replay happens and
the directory "y" does not exist nor do the files "foo" and
"bar" exist anywhere (neither in "y" nor in "x", nor the root
nor anywhere).
The next time the fs is mounted, log tree replay happens and the
file "bar" does not exists anymore. A file with the name "foo"
exists and it matches the second file we created.
Another related problem that does not involve file/data loss is when a
new inode is created with the name of a deleted snapshot and we fsync it:
The next time the fs is mounted the log replay procedure fails because
it attempts to delete the snapshot entry (which has dir item key type
of BTRFS_ROOT_ITEM_KEY) as if it were a regular (non-root) entry,
resulting in the following error that causes mount to fail:
Fix this by forcing a transaction commit when such cases happen.
This means we check in the commit root of the subvolume tree if there
was any other inode with the same reference when the inode we are
fsync'ing is a new inode (created in the current transaction).
Test cases for fstests, covering all the scenarios given above, were
submitted upstream for fstests:
* fstests: generic test for fsync after renaming directory
https://patchwork.kernel.org/patch/8694281/
* fstests: generic test for fsync after renaming file
https://patchwork.kernel.org/patch/8694301/
* fstests: add btrfs test for fsync after snapshot deletion
https://patchwork.kernel.org/patch/8670671/
Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
IOMMU drivers that do not support default domains, but make
use of the the group->domain pointer can get that pointer
overwritten with NULL on device add/remove.
Make sure this can't happen by only overwriting the domain
pointer when it is NULL.
Previously, ext4 would fail the mount if the file system had the quota
feature enabled and quota mount options (used for the older quota
setups) were present. This broke xfstests, since xfs silently ignores
the usrquote and grpquota mount options if they are specified. This
commit changes things so that we are consistent with xfs; having the
mount options specified is harmless, so no sense break users by
forbidding them.
With the internal Quota feature, mke2fs creates empty quota inodes and
quota usage tracking is enabled as soon as the file system is mounted.
Since quotacheck is no longer preallocating all of the blocks in the
quota inode that are likely needed to be written to, we are now seeing
a lockdep false positive caused by needing to allocate a quota block
from inside ext4_map_blocks(), while holding i_data_sem for a data
inode. This results in this complaint:
If the lower or upper directory of an overlayfs mount belong to a btrfs
file system and we fsync the file through the overlayfs' merged directory
we ended up accessing an inode that didn't belong to btrfs as if it were
a btrfs inode at btrfs_sync_file() resulting in a crash like the following:
This started happening since commit 4bacc9c9234 (overlayfs: Make f_path
always point to the overlay and f_inode to the underlay) and even though
after this change we could still access the btrfs inode through
struct file->f_mapping->host or struct file->f_inode, we would end up
resulting in more similar issues later on at check_parent_dirs_for_sync()
because the dentry we got (from struct file->f_path.dentry) was from
overlayfs and not from btrfs, that is, we had no way of getting the dentry
that belonged to btrfs (we always got the dentry that belonged to
overlayfs).
The new patch from Miklos Szeredi, titled "vfs: add file_dentry()" and
recently submitted to linux-fsdevel, adds a file_dentry() API that allows
us to get the btrfs dentry from the input file and therefore being able
to fsync when the upper and lower directories belong to btrfs filesystems.
This issue has been reported several times by users in the mailing list
and bugzilla. A test case for xfstests is being submitted as well.
Fixes: 4bacc9c9234c ("overlayfs: Make f_path always point to the overlay and f_inode to the underlay")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=101951
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=109791 Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
NFS may be used as lower layer of overlayfs and accessing f_path.dentry can
lead to a crash.
Fix by replacing direct access of file->f_path.dentry with the
file_dentry() accessor, which will always return a native object.
Fixes: 4bacc9c9234c ("overlayfs: Make f_path always point to the overlay and f_inode to the underlay") Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Tested-by: Goldwyn Rodrigues <rgoldwyn@suse.com> Acked-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Cc: David Howells <dhowells@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
This series fixes bugs in nfs and ext4 due to 4bacc9c9234c ("overlayfs:
Make f_path always point to the overlay and f_inode to the underlay").
Regular files opened on overlayfs will result in the file being opened on
the underlying filesystem, while f_path points to the overlayfs
mount/dentry.
This confuses filesystems which get the dentry from struct file and assume
it's theirs.
Add a new helper, file_dentry() [*], to get the filesystem's own dentry
from the file. This checks file->f_path.dentry->d_flags against
DCACHE_OP_REAL, and returns file->f_path.dentry if DCACHE_OP_REAL is not
set (this is the common, non-overlayfs case).
In the uncommon case it will call into overlayfs's ->d_real() to get the
underlying dentry, matching file_inode(file).
The reason we need to check against the inode is that if the file is copied
up while being open, d_real() would return the upper dentry, while the open
file comes from the lower dentry.
[*] If possible, it's better simply to use file_inode() instead.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Tested-by: Goldwyn Rodrigues <rgoldwyn@suse.com> Reviewed-by: Trond Myklebust <trond.myklebust@primarydata.com> Cc: David Howells <dhowells@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Daniel Axtens <dja@axtens.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
During revalidate we check whether device capacity has changed before we
decide whether to output disk information or not.
The check for old capacity failed to take into account that we scaled
sdkp->capacity based on the reported logical block size. And therefore
the capacity test would always fail for devices with sectors bigger than
512 bytes and we would print several copies of the same discovery
information.
Avoid scaling sdkp->capacity and instead adjust the value on the fly
when setting the block device capacity and generating fake C/H/S
geometry.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Reported-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Hannes Reinicke <hare@suse.de> Reviewed-by: Ewan Milne <emilne@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
For big endian platforms, reading the axes will return
invalid values.
The device stores each axis value in a 16 bit little
endian register. The driver uses regmap_read_bulk to get
the axis value, resulting in a 16 bit little endian value.
This needs to be converted to cpu endianness to work
on big endian platforms.
Fix endianness for big endian platforms by converting
the values for the axes read from little endian to
cpu.
This is also partially fixed in commit 82d8e5da1a33 ("iio:
accel: bmg160: optimize transfers in trigger handler").
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
When reading gyroscope axes using iio buffers, the values
returned are always 0. In the interrupt handler, the return
value of the read operation is returned to the user instead
of the value read. Return the value read to the user.
This is also fixed in commit 82d8e5da1a33 ("iio:
accel: bmg160: optimize transfers in trigger handler").
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
For big endian platforms, reading the axes will return
invalid values.
The device stores each axis value in a 16 bit little
endian register. The driver uses regmap_read_bulk to get
the axis value, resulting in a 16 bit little endian value.
This needs to be converted to cpu endianness to work
on big endian platforms.
Fix endianness for big endian platforms by converting
the values for the axes read from little endian to
cpu.
This is also partially fixed in commit b6fb9b6d6552 ("iio:
accel: bmc150: optimize transfers in trigger handler").
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
When CONFIG_IIO_TRIGGER is enabled but CONFIG_IIO_BUFFER is
not, we get a build error in the st_magn driver:
drivers/iio/magnetometer/st_magn_core.c:573:23: error: 'ST_MAGN_TRIGGER_SET_STATE' undeclared here (not in a function)
.set_trigger_state = ST_MAGN_TRIGGER_SET_STATE,
^~~~~~~~~~~~~~~~~~~~~~~~~
Apparently, this ST_MAGN_TRIGGER_SET_STATE macro was meant to
be set to NULL when the definition is not available because
st_magn_buffer.c is not compiled, but the alternative definition
was not included in the original patch. This adds it.
This patch fixes an issue that usbhsg_queue_done() may cause kernel
panic when dma callback is running and usb_ep_disable() is called
by interrupt handler. (Especially, we can reproduce this issue using
g_audio with usb-dmac driver.)
For example of a flow:
usbhsf_dma_complete (on tasklet)
--> usbhsf_pkt_handler (on tasklet)
--> usbhsg_queue_done (on tasklet)
*** interrupt happened and usb_ep_disable() is called ***
--> usbhsg_queue_pop (on tasklet)
Then, oops happened.
This patch adds a code to surely disable TX IRQ of the pipe before
starting TX DMAC transfer. Otherwise, a lot of unnecessary TX IRQs
may happen in rare cases when DMAC is used.
When unexpected situation happened (e.g. tx/rx irq happened while
DMAC is used), the usbhsf_pkt_handler() was possible to cause NULL
pointer dereference like the followings:
The driver can access the queue simultanously
while mac80211 tears down the interface. Without
spinlock protection this could lead to corrupting
sk_buff_head and subsequently to an invalid
pointer dereference.
Fixes: ba8c3d6f16a1 ("mac80211: add an intermediate software queue implementation") Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
The ieee80211_queue_stopped() expects hw queue
number but it was given raw WMM AC number instead.
This could cause frame drops and problems with
traffic in some cases - most notably if driver
doesn't map AC numbers to queue numbers 1:1 and
uses ieee80211_stop_queues() and
ieee80211_wake_queue() only without ever calling
ieee80211_wake_queues().
On ath10k it was possible to hit this problem in
the following case:
1. wlan0 uses queue 0
(ath10k maps queues per vif)
2. offchannel uses queue 15
3. queues 1-14 are unused
4. ieee80211_stop_queues()
5. ieee80211_wake_queue(q=0)
6. ieee80211_wake_queue(q=15)
(other queues are not woken up because both
driver and mac80211 know other queues are
unused)
7. ieee80211_rx_h_mesh_fwding()
8. ieee80211_select_queue_80211() returns 2
9. ieee80211_queue_stopped(q=2) returns true
10. frame is dropped (oops!)
Fixes: d3c1597b8d1b ("mac80211: fix forwarded mesh frame queue mapping") Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
When joining IBSS a full scan should be initiated in order to search
for existing cell, unless the fixed_channel parameter was set.
A default channel to create the IBSS on if no cell was found is
provided as well.
However - a scan is initiated only on the default channel provided
regardless of whether ifibss->fixed_channel is set or not, with the
obvious result of the cell not joining existing IBSS cell that is
on another channel.
Fixes: 76bed0f43b27 ("mac80211: IBSS fix scan request") Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
When CONFIG_OPTIMIZE_INLINING is set, the sta_info_insert_finish
function consumes more stack than normally, exceeding the
1024 byte limit on ARM:
net/mac80211/sta_info.c: In function 'sta_info_insert_finish':
net/mac80211/sta_info.c:561:1: error: the frame size of 1080 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
It turns out that there are two functions that put a 'struct station_info'
on the stack: __sta_info_destroy_part2 and sta_info_insert_finish, and
this structure alone requires up to 792 bytes.
Hoping that both are called rarely enough, this replaces the
on-stack structure with a dynamic allocation, which unfortunately
requires some suboptimal error handling for out-of-memory.
The __sta_info_destroy_part2 function is actually affected by the
stack usage twice because it calls cfg80211_del_sta_sinfo(), which
has another instance of struct station_info on its stack.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: 98b6218388e3 ("mac80211/cfg80211: add station events") Fixes: 6f7a8d26e266 ("mac80211: send statistics with delete station event") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
The original hand-implemented hash-table in mac80211 couldn't result
in insertion errors, and while converting to rhashtable I evidently
forgot to check the errors.
This surfaced now only because Ben is adding many identical keys and
that resulted in hidden insertion errors.
Fixes: 7bedd0cfad4e1 ("mac80211: use rhashtable for station table") Reported-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
The spec says: after writing 0 to device_status, the driver MUST wait
for a read of device_status to return 0 before reinitializing the
device.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
As of 5a60e87603c4c533492c515b7f62578189b03c9c, RBD object request
allocations are made via rbd_obj_request_create() with GFP_NOIO.
However, subsequent OSD request allocations in rbd_osd_req_create*()
use GFP_ATOMIC.
With heavy page cache usage (e.g. OSDs running on same host as krbd
client), rbd_osd_req_create() order-1 GFP_ATOMIC allocations have been
observed to fail, where direct reclaim would have allowed GFP_NOIO
allocations to succeed.
Suggested-by: Vlastimil Babka <vbabka@suse.cz> Suggested-by: Neil Brown <neilb@suse.com> Signed-off-by: David Disseldorp <ddiss@suse.de> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
remove the usage of removed irq_to_gpio() function. On pre-DB1200
boards, pass the actual carddetect GPIO number instead of the IRQ,
because we need the gpio to actually test card status (inserted or
not) and can get the irq number with gpio_to_irq() instead.
Tested on DB1300 and DB1500, this patch fixes PCMCIA on the DB1500,
which used irq_to_gpio().
Fixes: 832f5dacfa0b ("MIPS: Remove all the uses of custom gpio.h") Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Cc: linux-pcmcia@lists.infradead.org Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/12747/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Commit 58f896d859ce ("[media] v4l: vsp1: sru: Make the intensity
controllable during streaming") refactored the stream start code and
removed the SRU CTRL0 register write by mistake. Add it back.
Fixes: 58f896d859ce ("[media] v4l: vsp1: sru: Make the intensity controllable during streaming") Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
The au0828 dev_state is actually a bit mask. It should not be
checking with "==" but, instead, with a logic and. There are some
places where it was doing it wrong.
Fix that by replacing the dev_state set/clear/test with the
bitops.
As reviewed by Shuah:
"Looks good. Tested running bind/unbind au0828 loop for 1000 times.
Didn't see any problems and the v4l2_querycap() problem has been
fixed with this patch.
After the above test, ran bind/unbind snd_usb_audio 1000 times.
Didn't see any problems. Generated media graph and the graph
looks good."
au0828_v4l2_close() check for dev_state == DEV_DISCONNECTED will fail to
detect the device disconnected state correctly, if au0828_v4l2_open() runs
to set the DEV_INITIALIZED bit. A loop test of bind/unbind found this bug
by increasing the likelihood of au0828_v4l2_open() occurring while unbind
is in progress. When au0828_v4l2_close() fails to detect that the device
is in disconnect state, it attempts to power down the device and fails with
the following general protection fault:
pinctrl-sun8i-a33.c (and the dts) declare only 2 interrupt banks,
where as the closely related a23 has 3 banks. This matches with the
datasheet for the A33 where only interrupt banks B and G are specified
where as the A23 has banks A, B and G.
However the A33 being the A23 derative it is means that the interrupt
configure/status io-addresses for the 2 banks it has are not changed
from the A23, iow they have the same address as if bank A was still
present. Where as the sunxi pinctrl currently tries to use the A23 bank
A addresses for bank B, since the pinctrl code does not know about the
removed bank A.
Add a irq_bank_base parameter and use this where appropriate to take
the missing bank A into account.
This fixes external interrupts not working on the A33 (tested with
an i2c touchscreen controller which uses an external interrupt).
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
If pinctrl_provide_dummies() is used unconditionally, then the dummy
state will be used even on DT platforms when the "init" state was
intentionally left out. Instead of "default", the dummy "init" state
will then be used during probe. Thus, when probing an I2C controller on
cold boot, communication triggered by bus notifiers broke because the
pins were not initialized.
Do it like OMAP2: use the dummy state only for non-DT platforms.
Fixes: ef0eebc05130 ("drivers/pinctrl: Add the concept of an "init" state") Reported-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Copying the content of an MSA vector from user memory may involve TLB
faults & mapping in pages. This will fail when preemption is disabled
due to an inability to acquire mmap_sem from do_page_fault, which meant
such vector loads to unmapped pages would always fail to be emulated.
Fix this by disabling preemption later only around the updating of
vector register state.
This change does however introduce a race between performing the load
into thread context & the thread being preempted, saving its current
live context & clobbering the loaded value. This should be a rare
occureence, so optimise for the fast path by simply repeating the load if
we are preempted.
Additionally if the copy failed then the failure path was taken with
preemption left disabled, leading to the kernel typically encountering
further issues around sleeping whilst atomic. The change to where
preemption is disabled avoids this issue.
Fixes: e4aa1f153add "MIPS: MSA unaligned memory access support" Reported-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Paul Burton <paul.burton@imgtec.com> Reviewed-by: James Hogan <james.hogan@imgtec.com> Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com> Cc: Maciej W. Rozycki <macro@linux-mips.org> Cc: James Cowgill <James.Cowgill@imgtec.com> Cc: Markos Chandras <markos.chandras@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12345/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Windows lets applications choose the frequency of the timer tick,
and in Windows 10 the maximum rate was changed from 1024 Hz to
2048 Hz. Unfortunately, because of the way the Windows API
works, most applications who need a higher rate than the default
64 Hz will just do
and pick the maximum rate. This causes very high CPU usage when
playing media or games on Windows 10, even if the guest does not
actually use the CPU very much, because the frequent timer tick
causes halt_poll_ns to kick in.
There is no really good solution, especially because Microsoft
could sooner or later bump the limit to 4096 Hz, but for now
the best we can do is lower a bit the upper limit for
halt_poll_ns. :-(
Reported-by: Jon Panozzo <jonp@lime-technology.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Non maskable interrupts (NMI) are preferred to interrupts in current
implementation. If a NMI is pending and NMI is blocked by the result
of nmi_allowed(), pending interrupt is not injected and
enable_irq_window() is not executed, even if interrupts injection is
allowed.
In old kernel (e.g. 2.6.32), schedule() is often called in NMI context.
In this case, interrupts are needed to execute iret that intends end
of NMI. The flag of blocking new NMI is not cleared until the guest
execute the iret, and interrupts are blocked by pending NMI. Due to
this, iret can't be invoked in the guest, and the guest is starved
until block is cleared by some events (e.g. canceling injection).
This patch injects pending interrupts, when it's allowed, even if NMI
is blocked. And, If an interrupts is pending after executing
inject_pending_event(), enable_irq_window() is executed regardless of
NMI pending counter.
Signed-off-by: Yuki Shibuya <shibuya.yk@ncos.nec.co.jp> Suggested-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
The union descriptor must be checked. Its usage was conditional
before the parser was introduced. This is important, because
many RNDIS device, which also use the common parser, have
bogus extra descriptors.
Signed-off-by: Oliver Neukum <oneukum@suse.com> Tested-by: Vasily Galkin <galkin-vv@yandex.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Add a new NO_REPORT_LUNS quirk and set it for Seagate drives with
an usb-id of: 0bc2:331a, as these will fail to respond to a
REPORT_LUNS command.
Reported-and-tested-by: David Webb <djw@noc.ac.uk> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Commit 64d513ac31bd ("scsi: use host wide tags by default") causes
the SCSI core to queue more commands then we can handle on devices with
multiple LUNs, limit the queue depth at the scsi-host level instead of
per slave to fix this.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1315013 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
find_outdev calls inet{,6}_fib_lookup_dev() or dev_get_by_index() to
find the output device. In case of an error, inet{,6}_fib_lookup_dev()
returns error pointer and dev_get_by_index() returns NULL. But the function
only checks for NULL and thus can end up calling dev_put on an ERR_PTR.
This patch adds an additional check for err ptr after the NULL check.
After patch:
$ip -f mpls route add 100 as 200 via inet 10.1.1.8
RTNETLINK answers: Network is unreachable
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Reported-by: David Miller <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
When sending a UDPv6 message longer than MTU, account for the length
of fragmentable IPv6 extension headers in skb->network_header offset.
Same as we do in alloc_new_skb path in __ip6_append_data().
This ensures that later on __ip6_make_skb() will make space in
headroom for fragmentable extension headers:
/* move skb->data to ip header from ext header */
if (skb->data < skb_network_header(skb))
__skb_pull(skb, skb_network_offset(skb));
Reported-by: Ji Jianwen <jiji@redhat.com> Signed-off-by: Jakub Sitnicki <jkbs@redhat.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
When creating an ip6tnl tunnel with ip tunnel, rtnl_link_ops is not set
before ip6_tnl_create2 is called. When register_netdevice is called, there
is no linkinfo attribute in the NEWLINK message because of that.
Setting rtnl_link_ops before calling register_netdevice fixes that.
Fixes: 0b112457229d ("ip6tnl: add support of link creation via rtnl") Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@redhat.com> Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
pskb_may_pull() can change skb->data, so we have to load ptr/optr at the
right place.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
pskb_may_pull() can change skb->data, so we have to load ptr/optr at the
right place.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
After commit f84bb1eac027 ("net: fix IFF_NO_QUEUE for drivers using
alloc_netdev"), default qdisc was changed to noqueue because
tuntap does not set tx_queue_len during .setup(). This patch restores
default qdisc by setting tx_queue_len in tun_setup().
Fixes: f84bb1eac027 ("net: fix IFF_NO_QUEUE for drivers using alloc_netdev") Cc: Phil Sutter <phil@nwl.cc> Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Phil Sutter <phil@nwl.cc> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Same can be triggered with PROVE_RCU (+ PROVE_RCU_REPEATEDLY) enabled
from tun_attach_filter() when user space calls ioctl(tun_fd, TUN{ATTACH,
DETACH}FILTER, ...) for adding/removing a BPF filter on tap devices.
Since the fix in f91ff5b9ff52 ("net: sk_{detach|attach}_filter() rcu
fixes") sk_attach_filter()/sk_detach_filter() now dereferences the
filter with rcu_dereference_protected(), checking whether socket lock
is held in control path.
Since its introduction in 994051625981 ("tun: socket filter support"),
tap filters are managed under RTNL lock from __tun_chr_ioctl(). Thus the
sock_owned_by_user(sk) doesn't apply in this specific case and therefore
triggers the false positive.
Extend the BPF API with __sk_attach_filter()/__sk_detach_filter() pair
that is used by tap filters and pass in lockdep_rtnl_is_held() for the
rcu_dereference_protected() checks instead.
Reported-by: Sasha Levin <sasha.levin@oracle.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Size of the attribute IFLA_PHYS_PORT_NAME was missing.
Fixes: db24a9044ee1 ("net: add support for phys_port_name") CC: David Ahern <dsahern@gmail.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
When NET_SWITCHDEV=n, switchdev_port_attr_set will return -EOPNOTSUPP,
we should ignore this error code and continue to set the ageing time.
Fixes: c62987bbd8a1 ("bridge: push bridge setting ageing_time down to switchdev") Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com> Acked-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
IPv6 counters updates use a different macro than IPv4.
Fixes: 36cbb2452cbaf ("udp: Increment UDP_MIB_IGNOREDMULTI for arriving unmatched multicasts") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Rick Jones <rick.jones2@hp.com> Cc: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Reported-by: Thomas Schäfer <tschaefer@t-online.de> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
A crash is observed when a decrypted packet is processed in receive
path. get_rps_cpus() tries to dereference the skb->dev fields but it
appears that the device is freed from the poison pattern.
-013|get_rps_cpu(
| dev = 0xFFFFFFC08B688000,
| skb = 0xFFFFFFC0C76AAC00 -> (
| dev = 0xFFFFFFC08B688000 -> (
| name =
"......................................................
| name_hlist = (next = 0xAAAAAAAAAAAAAAAA, pprev =
0xAAAAAAAAAAA
Following are the sequence of events observed -
- Encrypted packet in receive path from netdevice is queued
- Encrypted packet queued for decryption (asynchronous)
- Netdevice brought down and freed
- Packet is decrypted and returned through callback in esp_input_done
- Packet is queued again for process in network stack using netif_rx
Since the device appears to have been freed, the dereference of
skb->dev in get_rps_cpus() leads to an unhandled page fault
exception.
Fix this by holding on to device reference when queueing packets
asynchronously and releasing the reference on call back return.
v2: Make the change generic to xfrm as mentioned by Steffen and
update the title to xfrm
Suggested-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Jerome Stanislaus <jeromes@codeaurora.org> Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Let channels hold a reference on their network namespace.
Some channel types, like ppp_async and ppp_synctty, can have their
userspace controller running in a different namespace. Therefore they
can't rely on them to preclude their netns from being removed from
under them.
==================================================================
BUG: KASAN: use-after-free in ppp_unregister_channel+0x372/0x3a0 at
addr ffff880064e217e0
Read of size 8 by task syz-executor/11581
=============================================================================
BUG net_namespace (Not tainted): kasan: bad access detected
-----------------------------------------------------------------------------
Field fl4.flowi4_flags is not initialized in fib_compute_spec_dst()
before calling fib_lookup(), which means fib_table_lookup() is
using non-deterministic data at this line:
if (!(flp->flowi4_flags & FLOWI_FLAG_SKIP_NH_OIF)) {
Fix by initializing the entire fl4 structure, which will prevent
similar issues as fields are added in the future by ensuring that
all fields are initialized to zero unless explicitly initialized
to another value.
Fixes: 58189ca7b2741 ("net: Fix vti use case with oif in dst lookups") Suggested-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: Lance Richardson <lrichard@redhat.com> Acked-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Currently, ingress ipv4 broadcast datagrams are dropped since,
in udp_v4_early_demux(), ip_check_mc_rcu() is invoked even on
bcast packets.
This patch addresses the issue, invoking ip_check_mc_rcu()
only for mcast packets.
Fixes: 6e5403093261 ("ipv4/udp: Verify multicast group is ours in upd_v4_early_demux()") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
bond_get_stats() can be called from rtnetlink (with RTNL held)
or from /proc/net/dev seq handler (with RCU held)
The logic added in commit 5f0c5f73e5ef ("bonding: make global bonding
stats more reliable") kind of assumed only one cpu could run there.
If multiple threads are reading /proc/net/dev, stats can be really
messed up after a while.
A second problem is that some fields are 32bit, so we need to properly
handle the wrap around problem.
Given that RTNL is not always held, we need to use
bond_for_each_slave_rcu().
Fixes: 5f0c5f73e5ef ("bonding: make global bonding stats more reliable") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Andy Gospodarek <gospo@cumulusnetworks.com> Cc: Jay Vosburgh <j.vosburgh@gmail.com> Cc: Veaceslav Falico <vfalico@gmail.com> Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
When un-mapping skb->data in __bcmgenet_tx_reclaim(),
we must use the length that was used in original dma_map_single(),
instead of skb->len that might be bigger (includes the frags)
We simply can store skb_len into tx_cb_ptr->dma_len and use it
at unmap time.
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file") Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
When running small packets [length < 256 bytes] traffic, packets were
being dropped due to invalid data in those packets which were
delivered by the driver upto the stack. Using pci_dma_sync_single_for_cpu
ensures copying latest and updated data into skb from the receive buffer.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com> Signed-off-by: Manish Chopra <manish.chopra@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Now SYN_RECV request sockets are installed in ehash table, an ICMP
handler can find a request socket while another cpu handles an incoming
packet transforming this SYN_RECV request socket into an ESTABLISHED
socket.
We need to remove the now obsolete WARN_ON(req->sk), since req->sk
is set when a new child is created and added into listener accept queue.
If this race happens, the ICMP will do nothing special.
Fixes: 079096f103fa ("tcp/dccp: install syn_recv requests into ehash table") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Ben Lazarus <blazarus@google.com> Reported-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Locking ppp_mutex must be done before dereferencing file->private_data,
otherwise it could be modified before ppp_unattached_ioctl() takes the
lock. This could lead ppp_unattached_ioctl() to override ->private_data,
thus leaking reference to the ppp_file previously pointed to.
v2: lock all ppp_ioctl() instead of just checking private_data in
ppp_unattached_ioctl(), to avoid ambiguous behaviour.
Fixes: f3ff8a4d80e8 ("ppp: push BKL down into the driver") Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Code that was added back in 2.6.38 has an obvious overflow
when accessing a static array, and at the time it was added
only a code comment was put in front of it as a reminder
to have it reviewed properly.
This has not happened, but gcc-6 now points to the specific
overflow:
drivers/net/wireless/ath/ath9k/eeprom.c: In function 'ath9k_hw_get_gain_boundaries_pdadcs':
drivers/net/wireless/ath/ath9k/eeprom.c:483:44: error: array subscript is above array bounds [-Werror=array-bounds]
maxPwrT4[i] = data_9287[idxL].pwrPdg[i][4];
~~~~~~~~~~~~~~~~~~~~~~~~~^~~
It turns out that the correct array length exists in the local
'intercepts' variable of this function, so we can just use that
instead of hardcoding '4', so this patch changes all three
instances to use that variable. The other two instances were
already correct, but it's more consistent this way.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: 940cd2c12ebf ("ath9k_hw: merge the ar9287 version of ath9k_hw_get_gain_boundaries_pdadcs") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
gcc-6 finds an out of bounds access in the fst_add_one function
when calculating the end of the mmio area:
drivers/net/wan/farsync.c: In function 'fst_add_one':
drivers/net/wan/farsync.c:418:53: error: index 2 denotes an offset greater than size of 'u8[2][8192] {aka unsigned char[2][8192]}' [-Werror=array-bounds]
#define BUF_OFFSET(X) (BFM_BASE + offsetof(struct buf_window, X))
^
include/linux/compiler-gcc.h:158:21: note: in definition of macro '__compiler_offsetof'
__builtin_offsetof(a, b)
^
drivers/net/wan/farsync.c:418:37: note: in expansion of macro 'offsetof'
#define BUF_OFFSET(X) (BFM_BASE + offsetof(struct buf_window, X))
^~~~~~~~
drivers/net/wan/farsync.c:2519:36: note: in expansion of macro 'BUF_OFFSET'
+ BUF_OFFSET ( txBuffer[i][NUM_TX_BUFFER][0]);
^~~~~~~~~~
The warning is correct, but not critical because this appears
to be a write-only variable that is set by each WAN driver but
never accessed afterwards.
I'm taking the minimal fix here, using the correct pointer by
pointing 'mem_end' to the last byte inside of the register area
as all other WAN drivers do, rather than the first byte outside of
it. An alternative would be to just remove the mem_end member
entirely.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
The implementation of QP paravirtualization back in linux-3.7 included
some code that looks very dubious, and gcc-6 has grown smart enough
to warn about it:
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'verify_qp_parameters':
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:3154:5: error: statement is indented as if it were guarded by... [-Werror=misleading-indentation]
if (optpar & MLX4_QP_OPTPAR_ALT_ADDR_PATH) {
^~
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:3144:4: note: ...this 'if' clause, but it is not
if (slave != mlx4_master_func_num(dev))
>From looking at the context, I'm reasonably sure that the indentation
is correct but that it should have contained curly braces from the
start, as the update_gid() function in the same patch correctly does.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: 54679e148287 ("mlx4: Implement QP paravirtualization and maintain phys_pkey_cache for smp_snoop") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
And, as Dmitry rightly assessed, that is because we can drop the
reference and then touch it when the underlying recvmsg calls return
some packets and then hit an error, which will make recvmmsg to set
sock->sk->sk_err, oops, fix it.
Reported-and-Tested-by: Dmitry Vyukov <dvyukov@google.com> Cc: Alexander Potapenko <glider@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Kostya Serebryany <kcc@google.com> Cc: Sasha Levin <sasha.levin@oracle.com> Fixes: a2e2725541fa ("net: Introduce recvmmsg socket syscall")
http://lkml.kernel.org/r/20160122211644.GC2470@redhat.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
When an inetdev is destroyed, every address assigned to the interface
is removed. And in this scenerio we do two pointless things which can
be very expensive if the number of assigned interfaces is large:
1) Address promotion. We are deleting all addresses, so there is no
point in doing this.
2) A full nf conntrack table purge for every address. We only need to
do this once, as is already caught by the existing
masq_dev_notifier so masq_inet_event() can skip this.
Reported-by: Solar Designer <solar@openwall.com> Signed-off-by: David S. Miller <davem@davemloft.net> Tested-by: Cyrill Gorcunov <gorcunov@openvz.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
This fixes a regression in the bridge ageing time caused by:
commit c62987bbd8a1 ("bridge: push bridge setting ageing_time down to switchdev")
There are users of Linux bridge which use the feature that if ageing time
is set to 0 it causes entries to never expire. See:
https://www.linuxfoundation.org/collaborate/workgroups/networking/bridge
For a pure software bridge, it is unnecessary for the code to have
arbitrary restrictions on what values are allowable.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
In rocker, ageing time is a per-port attribute, so the next time the FDB
cleanup timer fires should be set according to the lowest ageing time.
This will later allow us to delete the BR_MIN_AGEING_TIME macro, which was
added to guarantee minimum ageing time in the bridge layer, thereby breaking
existing behavior.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Commit c62987bbd8a1 ("bridge: push bridge setting ageing_time down to
switchdev") added a check for minimum and maximum ageing time, but this
breaks existing behaviour where one can set ageing time to 0 for a
non-learning bridge.
Push this check down to the driver and allow the check in the bridge
layer to be removed. Currently ageing time 0 is refused by the driver,
but we can later add support for this functionality.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
The stack expects link layer headers in the skb linear section.
Macvtap can create skbs with llheader in frags in edge cases:
when (IFF_VNET_HDR is off or vnet_hdr.hdr_len < ETH_HLEN) and
prepad + len > PAGE_SIZE and vnet_hdr.flags has no or bad csum.
Add checks to ensure linear is always at least ETH_HLEN.
At this point, len is already ensured to be >= ETH_HLEN.
For backwards compatiblity, rounds up short vnet_hdr.hdr_len.
This differs from tap and packet, which return an error.
Fixes b9fb9ee07e67 ("macvtap: add GSO/csum offload support") Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
o While the driver is in the middle of a MB completion processing
and it receives a spurious MB interrupt, it is mistaken as a good MB
completion interrupt leading to premature completion of the next MB
request. Fix the driver to guard against this by checking the current
state of MB processing and ignore the spurious interrupt.
Also added a stats counter to record this condition.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
o atomic_t usage is incorrect as we are not implementing
any atomicity.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Iff dma_map_single() fails, 'rxdesc' should point to the last filled RX
descriptor, so that it can be marked as the last one, however the driver
would have already advanced it by that time. In order to fix that, only
fill an RX descriptor once all the data for it is ready.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
In a low memory situation, if netdev_alloc_skb() fails on a first RX ring
loop iteration in sh_eth_ring_format(), 'rxdesc' is still NULL. Avoid
kernel oops by adding the 'rxdesc' check after the loop.
Reported-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Lots of places in the kernel use memcpy(buf, comm, TASK_COMM_LEN); but
the result is typically passed to print("%s", buf) and extra bytes
after zero don't cause any harm.
In bpf the result of bpf_get_current_comm() is used as the part of
map key and was causing spurious hash map mismatches.
Use strlcpy() to guarantee zero-terminated string.
bpf verifier checks that output buffer is zero-initialized,
so even for short task names the output buffer don't have junk bytes.
Note it's not a security concern, since kprobe+bpf is root only.
Fixes: ffeedafbf023 ("bpf: introduce current->pid, tgid, uid, gid, comm accessors") Reported-by: Tobias Waldekranz <tobias@waldekranz.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Replace link layer header validation check ll_header_truncate with
more generic dev_validate_header.
Validation based on hard_header_len incorrectly drops valid packets
in variable length protocols, such as AX25. dev_validate_header
calls header_ops.validate for such protocols to ensure correctness
below hard_header_len.
See also http://comments.gmane.org/gmane.linux.network/401064
Fixes 9c7077622dd9 ("packet: make packet_snd fail on len smaller than l2 header") Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
As variable length protocol, AX25 fails link layer header validation
tests based on a minimum length. header_ops.validate allows protocols
to validate headers that are shorter than hard_header_len. Implement
this callback for AX25.
See also http://comments.gmane.org/gmane.linux.network/401064
Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Netdevice parameter hard_header_len is variously interpreted both as
an upper and lower bound on link layer header length. The field is
used as upper bound when reserving room at allocation, as lower bound
when validating user input in PF_PACKET.
Clarify the definition to be maximum header length. For validation
of untrusted headers, add an optional validate member to header_ops.
Allow bypassing of validation by passing CAP_SYS_RAWIO, for instance
for deliberate testing of corrupt input. In this case, pad trailing
bytes, as some device drivers expect completely initialized headers.
See also http://comments.gmane.org/gmane.linux.network/401064
Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Add missing rtnl_unlock() in the error path of ppp_create_interface().
Fixes: 58a89ecaca53 ("ppp: fix lockdep splat in ppp_dev_uninit()") Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Fixes: 2efd055c53c06 ("tcp: add tcpi_segs_in and tcpi_segs_out to tcp_info") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
IPv4 interprets a negative return value from a protocol handler as a
request to redispatch to a new protocol. In contrast, IPv6 interprets a
negative value as an error, and interprets a positive value as a request
for redispatch.
UDP for IPv6 was unaware of this difference. Change __udp6_lib_rcv() to
return a positive value for redispatch. Note that the socket's
encap_rcv hook still needs to return a negative value to request
dispatch, and in the case of IPv6 packets, adjust IP6CB(skb)->nhoff to
identify the byte containing the next protocol.
Signed-off-by: Bill Sommerfeld <wsommerfeld@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Some devices will silently fail setup unless they are reset first.
This is necessary even if the data interface is already in
altsetting 0, which it will be when the device is probed for the
first time. Briefly toggling the altsetting forces a function
reset regardless of the initial state.
This fixes a setup problem observed on a number of Huawei devices,
appearing to operate in NTB-32 mode even if we explicitly set them
to NTB-16 mode.
Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
When signalling to metadata consumers that the metadata_dst entry
carries additional GBP extension data for vxlan (TUNNEL_VXLAN_OPT),
the dst's vxlan_metadata information is populated, but options_len
is left to zero. F.e. in ovs, ovs_flow_key_extract() checks for
options_len before extracting the data through ip_tunnel_info_opts_get().
Geneve uses ip_tunnel_info_opts_set() helper in receive path, which
sets options_len internally, vxlan however uses ip_tunnel_info_opts(),
so when filling vxlan_metadata, we do need to update options_len.
Fixes: 4c22279848c5 ("ip-tunnel: Use API to access tunnel metadata options.") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
When ipv6_find_hdr is used to find a fragment header
(caller specifies target NEXTHDR_FRAGMENT) we erronously return
-ENOENT for all fragments with nonzero offset.
Before commit 9195bb8e381d, when target was specified, we did not
enter the exthdr walk loop as nexthdr == target so this used to work.
Now we do (so we can skip empty route headers). When we then stumble upon
a frag with nonzero frag_off we must return -ENOENT ("header not found")
only if the caller did not specifically request NEXTHDR_FRAGMENT.
This allows nfables exthdr expression to match ipv6 fragments, e.g. via
nft add rule ip6 filter input frag frag-off gt 0
Fixes: 9195bb8e381d ("ipv6: improve ipv6_find_hdr() to skip empty routing headers") Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
The MC74xx and EM74xx modules use different IDs by default, according
to the Lenovo EM7455 driver for Windows.
Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
reverts commit 94153e36e709e ("tipc: use existing sk_write_queue for
outgoing packet chain")
In Commit 94153e36e709e, we assume that we fill & empty the socket's
sk_write_queue within the same lock_sock() session.
This is not true if the link is congested. During congestion, the
socket lock is released while we wait for the congestion to cease.
This implementation causes a nullptr exception, if the user space
program has several threads accessing the same socket descriptor.
Consider two threads of the same program performing the following:
Thread1 Thread2
-------------------- ----------------------
Enter tipc_sendmsg() Enter tipc_sendmsg()
lock_sock() lock_sock()
Enter tipc_link_xmit(), ret=ELINKCONG spin on socket lock..
sk_wait_event() :
release_sock() grab socket lock
: Enter tipc_link_xmit(), ret=0
: release_sock()
Wakeup after congestion
lock_sock()
skb = skb_peek(pktchain);
!! TIPC_SKB_CB(skb)->wakeup_pending = tsk->link_cong;
In this case, the second thread transmits the buffers belonging to
both thread1 and thread2 successfully. When the first thread wakeup
after the congestion it assumes that the pktchain is intact and
operates on the skb's in it, which leads to the following exception:
In this commit, we maintain the skb list always in the stack.
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com> Acked-by: Ying Xue <ying.xue@windriver.com> Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
The current reserved_tailroom calculation fails to take hlen and tlen into
account.
skb:
[__hlen__|__data____________|__tlen___|__extra__]
^ ^
head skb_end_offset
In this representation, hlen + data + tlen is the size passed to alloc_skb.
"extra" is the extra space made available in __alloc_skb because of
rounding up by kmalloc. We can reorder the representation like so:
[__hlen__|__data____________|__extra__|__tlen___]
^ ^
head skb_end_offset
The maximum space available for ip headers and payload without
fragmentation is min(mtu, data + extra). Therefore,
reserved_tailroom
= data + extra + tlen - min(mtu, data + extra)
= skb_end_offset - hlen - min(mtu, skb_end_offset - hlen - tlen)
= skb_tailroom - min(mtu, skb_tailroom - tlen) ; after skb_reserve(hlen)
Compare the second line to the current expression:
reserved_tailroom = skb_end_offset - min(mtu, skb_end_offset)
and we can see that hlen and tlen are not taken into account.
The min() in the third line can be expanded into:
if mtu < skb_tailroom - tlen:
reserved_tailroom = skb_tailroom - mtu
else:
reserved_tailroom = tlen
Depending on hlen, tlen, mtu and the number of multicast address records,
the current code may output skbs that have less tailroom than
dev->needed_tailroom or it may output more skbs than needed because not all
space available is used.
Fixes: 4c672e4b ("ipv6: mld: fix add_grhead skb_over_panic for devs with large MTUs") Signed-off-by: Benjamin Poirier <bpoirier@suse.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
As the member .cmp_addr of sctp_af_inet6, sctp_v6_cmp_addr should also check
the port of addresses, just like sctp_v4_cmp_addr, cause it's invoked by
sctp_cmp_addr_exact().
Now sctp_v6_cmp_addr just check the port when two addresses have different
family, and lack the port check for two ipv6 addresses. that will make
sctp_hash_cmp() cannot work well.
so fix it by adding ports comparison in sctp_v6_cmp_addr().
Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
We need to update the skb->csum after pulling the skb, otherwise
an unnecessary checksum (re)computation can ocure for IGMP/MLD packets
in the bridge code. Additionally this fixes the following splats for
network devices / bridge ports with support for and enabled RX checksum
offloading:
[...]
[ 43.986968] eth0: hw csum failure
[ 43.990344] CPU: 3 PID: 0 Comm: swapper/3 Not tainted 4.4.0 #2
[ 43.996193] Hardware name: BCM2709
[ 43.999647] [<800204e0>] (unwind_backtrace) from [<8001cf14>] (show_stack+0x10/0x14)
[ 44.007432] [<8001cf14>] (show_stack) from [<801ab614>] (dump_stack+0x80/0x90)
[ 44.014695] [<801ab614>] (dump_stack) from [<802e4548>] (__skb_checksum_complete+0x6c/0xac)
[ 44.023090] [<802e4548>] (__skb_checksum_complete) from [<803a055c>] (ipv6_mc_validate_checksum+0x104/0x178)
[ 44.032959] [<803a055c>] (ipv6_mc_validate_checksum) from [<802e111c>] (skb_checksum_trimmed+0x130/0x188)
[ 44.042565] [<802e111c>] (skb_checksum_trimmed) from [<803a06e8>] (ipv6_mc_check_mld+0x118/0x338)
[ 44.051501] [<803a06e8>] (ipv6_mc_check_mld) from [<803b2c98>] (br_multicast_rcv+0x5dc/0xd00)
[ 44.060077] [<803b2c98>] (br_multicast_rcv) from [<803aa510>] (br_handle_frame_finish+0xac/0x51c)
[...]
Fixes: 9afd85c9e455 ("net: Export IGMP/MLD message validation code") Reported-by: Álvaro Fernández Rojas <noltari@gmail.com> Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
ether_setup sets IFF_TX_SKB_SHARING but this is not supported by
qca_spi as it modifies the skb on xmit.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Fixes: 291ab06ecf67 (net: qualcomm: new Ethernet over SPI driver for QCA7000) Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Currently qcaspi_netdev_setup accidentally clears IFF_BROADCAST.
So fix this by keeping the flags from ether_setup.
Reported-by: Michael Heimpold <michael.heimpold@i2se.com> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Fixes: 291ab06ecf67 (net: qualcomm: new Ethernet over SPI driver for QCA7000) Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Nik pointed that the VRF driver should be using skb_header_pointer
instead of accessing skb->data and bits beyond directly which can
be garbage.
Fixes: 35402e313663 ("net: Add IPv6 support to VRF device") Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
The JMC260 network card fails to suspend/resume because the call to
jme_start_irq() was too early, moving the call to jme_start_irq() after
the call to jme_reset_link() makes it work.
Prior this change suspend/resume would fail unless /sys/power/pm_async=0
was explicitly specified.
Signed-off-by: Diego Viola <diego.viola@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
IPCB may contain data from previous layers (in the observed case the
qdisc layer). In the observed scenario, the data was misinterpreted as
ip header options, which later caused the ihl to be set to an invalid
value (<5). This resulted in an infinite loop in the mips implementation
of ip_fast_csum.
This patch clears IPCB(skb)->opt before dst_link_failure can be called for
various types of tunnels. This change only applies to encapsulated ipv4
packets.
The code introduced in 11c21a30 which clears all of IPCB has been removed
to be consistent with these changes, and instead the opt field is cleared
unconditionally in ip_tunnel_xmit. The change in ip_tunnel_xmit applies to
SIT, GRE, and IPIP tunnels.
The relevant vti, l2tp, and pptp functions already contain similar code for
clearing the IPCB.
Signed-off-by: Bernie Harris <bernie.harris@alliedtelesis.co.nz> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>