David S. Miller [Sun, 13 Nov 2016 04:38:08 +0000 (23:38 -0500)]
Merge branch 'fix-bpf_redirect'
Martin KaFai Lau says:
====================
bpf: Fix bpf_redirect to an ipip/ip6tnl dev
This patch set fixes a bug in bpf_redirect(dev, flags) when dev is an
ipip/ip6tnl. The current problem is IP-EthHdr-IP is sent out instead of
IP-IP.
Patch 1 adds a dev->type test similar to dev_is_mac_header_xmit()
in act_mirred.c which is only available in net-next. We can consider to
refactor it once this patch is pulled into net-next from net.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The test creates two netns, ns1 and ns2. The host (the default netns)
has an ipip or ip6tnl dev configured for tunneling traffic to the ns2.
ping VIPS from ns1 <----> host <--tunnel--> ns2 (VIPs at loopback)
The test is to have ns1 pinging VIPs configured at the loopback
interface in ns2.
The VIPs are 10.10.1.102 and 2401:face::66 (which are configured
at lo@ns2). [Note: 0x66 => 102].
At ns1, the VIPs are routed _via_ the host.
At the host, bpf programs are installed at the veth to redirect packets
from a veth to the ipip/ip6tnl. The test is configured in a way so
that both ingress and egress can be tested.
At ns2, the ipip/ip6tnl dev is configured with the local and remote address
specified. The return path is routed to the dev ipip/ip6tnl.
During egress test, the host also locally tests pinging the VIPs to ensure
that bpf_redirect at egress also works for the direct egress (i.e. not
forwarding from dev ve1 to ve2).
Acked-by: Alexei Starovoitov <ast@fb.com> Signed-off-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
If the bpf program calls bpf_redirect(dev, 0) and dev is
an ipip/ip6tnl, it currently includes the mac header.
e.g. If dev is ipip, the end result is IP-EthHdr-IP instead
of IP-IP.
The fix is to pull the mac header. At ingress, skb_postpull_rcsum()
is not needed because the ethhdr should have been pulled once already
and then got pushed back just before calling the bpf_prog.
At egress, this patch calls skb_postpull_rcsum().
If bpf_redirect(dev, BPF_F_INGRESS) is called,
it also fails now because it calls dev_forward_skb() which
eventually calls eth_type_trans(skb, dev). The eth_type_trans()
will set skb->type = PACKET_OTHERHOST because the mac address
does not match the redirecting dev->dev_addr. The PACKET_OTHERHOST
will eventually cause the ip_rcv() errors out. To fix this,
____dev_forward_skb() is added.
Joint work with Daniel Borkmann.
Fixes: cfc7381b3002 ("ip_tunnel: add collect_md mode to IPIP tunnel") Fixes: 8d79266bc48c ("ip6_tunnel: add collect_md mode to IPv6 tunnels") Acked-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@fb.com> Signed-off-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 10 Nov 2016 11:31:05 +0000 (12:31 +0100)]
mlxsw: spectrum_router: Ignore FIB notification events for non-init namespaces
Since now, the table with same id in multiple netnamespaces were squashed
to a single virtual router. That is not only incorrect, it also causes
error messages when trying to use RALUE register to do double remove
of FIB entries, like this one:
Since we don't allow ports to change namespaces (NETIF_F_NETNS_LOCAL),
and the infrastructure is not yet prepared to handle netnamespaces, just
ignore FIB notification events for non-init namespaces. That is clear to
do since we don't need to offload them.
Fixes: b45f64d16d45 ("mlxsw: spectrum_router: Use FIB notifications instead of switchdev calls") Signed-off-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 10 Nov 2016 11:31:04 +0000 (12:31 +0100)]
mlxsw: spectrum_router: Fix handling of neighbour structure
__neigh_create function works in a different way than assumed.
It passes "n" as a parameter to ndo_neigh_construct. But this "n" might
be destroyed right away before __neigh_create() returns in case there is
already another neighbour struct in the hashtable with the same dev and
primary key. That is not expected by mlxsw_sp_router_neigh_construct()
and the stored "n" points to freed memory, eventually leading to crash.
Fix this by doing tight 1:1 coupling between neighbour struct and
internal driver neigh_entry. That allows to narrow down the key in
internal driver hashtable to do lookups by "n" only.
Fixes: 6cf3c971dc84 ("mlxsw: spectrum_router: Add private neigh table") Signed-off-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 10 Nov 2016 17:55:26 +0000 (12:55 -0500)]
Merge branch 'qed-fixes'
Yuval Mintz says:
====================
qed: Fix RoCE infrastructure
This series fixes 2 basic issues with RoCE support,
one handles a missing configuration in the initial infrastructure
support while the other is a regression introduced by one of the
initial fix submissions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ram Amrani [Wed, 9 Nov 2016 20:48:44 +0000 (22:48 +0200)]
qed: Correct rdma params configuration
Previous fix has broken RoCE support as the rdma_pf_params are now
being set into the parameters only after the params are alrady assigned
into the hw-function.
Fixes: 0189efb8f4f8 ("qed*: Fix Kconfig dependencies with INFINIBAND_QEDR") Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ram Amrani [Wed, 9 Nov 2016 20:48:43 +0000 (22:48 +0200)]
qed: configure ll2 RoCE v1/v2 flavor correctly
Currently RoCE v2 won't operate with RDMA CM due to missing setting of
the roce-flavour in the ll2 configuration.
This patch properly sets the flavour, and deletes incorrect HSI
that doesn't [yet] exist.
Fixes: abd49676c707 ("qed: Add RoCE ll2 & GSI support") Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ipv4: update comment to document GSO fragmentation cases.
This is a follow-up to commit 9ee6c5dc816a ("ipv4: allow local
fragmentation in ip_finish_output_gso()"), updating the comment
documenting cases in which fragmentation is needed for egress
GSO packets.
Suggested-by: Shmulik Ladkani <shmulik.ladkani@gmail.com> Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com> Signed-off-by: Lance Richardson <lrichard@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 9 Nov 2016 17:07:26 +0000 (09:07 -0800)]
net: tcp response should set oif only if it is L3 master
Lorenzo noted an Android unit test failed due to e0d56fdd7342:
"The expectation in the test was that the RST replying to a SYN sent to a
closed port should be generated with oif=0. In other words it should not
prefer the interface where the SYN came in on, but instead should follow
whatever the routing table says it should do."
Revert the change to ip_send_unicast_reply and tcp_v6_send_response such
that the oif in the flow is set to the skb_iif only if skb_iif is an L3
master.
Fixes: e0d56fdd7342 ("net: l3mdev: remove redundant calls") Reported-by: Lorenzo Colitti <lorenzo@google.com> Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Tested-by: Lorenzo Colitti <lorenzo@google.com> Acked-by: Lorenzo Colitti <lorenzo@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Chou [Tue, 8 Nov 2016 22:08:01 +0000 (16:08 -0600)]
Net Driver: Add Cypress GX3 VID=04b4 PID=3610.
Add support for Cypress GX3 SuperSpeed to Gigabit Ethernet
Bridge Controller (Vendor=04b4 ProdID=3610).
Patch verified on x64 linux kernel 4.7.4, 4.8.6, 4.9-rc4 systems
with the Kensington SD4600P USB-C Universal Dock with Power,
which uses the Cypress GX3 SuperSpeed to Gigabit Ethernet Bridge
Controller.
A similar patch was signed-off and tested-by Allan Chou
<allan@asix.com.tw> on 2015-12-01.
Allan verified his similar patch on x86 Linux kernel 4.1.6 system
with Cypress GX3 SuperSpeed to Gigabit Ethernet Bridge Controller.
Tested-by: Allan Chou <allan@asix.com.tw> Tested-by: Chris Roth <chris.roth@usask.ca> Tested-by: Artjom Simon <artjom.simon@gmail.com> Signed-off-by: Allan Chou <allan@asix.com.tw> Signed-off-by: Chris Roth <chris.roth@usask.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
The following patchset contains a larger than usual batch of Netfilter
fixes for your net tree. This series contains a mixture of old bugs and
recently introduced bugs, they are:
1) Fix a crash when using nft_dynset with nft_set_rbtree, which doesn't
support the set element updates from the packet path. From Liping
Zhang.
2) Fix leak when nft_expr_clone() fails, from Liping Zhang.
3) Fix a race when inserting new elements to the set hash from the
packet path, also from Liping.
4) Handle segmented TCP SIP packets properly, basically avoid that the
INVITE in the allow header create bogus expectations by performing
stricter SIP message parsing, from Ulrich Weber.
5) nft_parse_u32_check() should return signed integer for errors, from
John Linville.
6) Fix wrong allocation instead of connlabels, allocate 16 instead of
32 bytes, from Florian Westphal.
7) Fix compilation breakage when building the ip_vs_sync code with
CONFIG_OPTIMIZE_INLINING on x86, from Arnd Bergmann.
8) Destroy the new set if the transaction object cannot be allocated,
also from Liping Zhang.
9) Use device to route duplicated packets via nft_dup only when set by
the user, otherwise packets may not follow the right route, again
from Liping.
10) Fix wrong maximum genetlink attribute definition in IPVS, from
WANG Cong.
11) Ignore untracked conntrack objects from xt_connmark, from Florian
Westphal.
12) Allow to use conntrack helpers that are registered NFPROTO_UNSPEC
via CT target, otherwise we cannot use the h.245 helper, from
Florian.
13) Revisit garbage collection heuristic in the new workqueue-based
timer approach for conntrack to evict objects earlier, again from
Florian.
14) Fix crash in nf_tables when inserting an element into a verdict map,
from Liping Zhang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Mathias Krause [Mon, 7 Nov 2016 22:22:19 +0000 (23:22 +0100)]
rtnl: reset calcit fptr in rtnl_unregister()
To avoid having dangling function pointers left behind, reset calcit in
rtnl_unregister(), too.
This is no issue so far, as only the rtnl core registers a netlink
handler with a calcit hook which won't be unregistered, but may become
one if new code makes use of the calcit hook.
Fixes: c7ac8679bec9 ("rtnetlink: Compute and store minimum ifinfo...") Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: Greg Rose <gregory.v.rose@intel.com> Signed-off-by: Mathias Krause <minipli@googlemail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Mon, 7 Nov 2016 21:09:07 +0000 (22:09 +0100)]
vxlan: hide unused local variable
A bugfix introduced a harmless warning in v4.9-rc4:
drivers/net/vxlan.c: In function 'vxlan_group_used':
drivers/net/vxlan.c:947:21: error: unused variable 'sock6' [-Werror=unused-variable]
This hides the variable inside of the same #ifdef that is
around its user. The extraneous initialization is removed
at the same time, it was accidentally introduced in the
same commit.
Fixes: c6fcc4fc5f8b ("vxlan: avoid using stale vxlan socket.") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
John Allen [Mon, 7 Nov 2016 20:27:28 +0000 (14:27 -0600)]
ibmvnic: Start completion queue negotiation at server-provided optimum values
Use the opt_* fields to determine the starting point for negotiating the
number of tx/rx completion queues with the vnic server. These contain the
number of queues that the vnic server estimates that it will be able to
allocate. While renegotiation may still occur, using the opt_* fields will
reduce the number of times this needs to happen and will prevent driver
probe timeout on systems using large numbers of ibmvnic client devices per
vnic port.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 7 Nov 2016 20:03:09 +0000 (12:03 -0800)]
net: icmp_route_lookup should use rt dev to determine L3 domain
icmp_send is called in response to some event. The skb may not have
the device set (skb->dev is NULL), but it is expected to have an rt.
Update icmp_route_lookup to use the rt on the skb to determine L3
domain.
Fixes: 613d09b30f8b ("net: Use VRF device index for lookups on TX") Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 9 Nov 2016 23:45:36 +0000 (18:45 -0500)]
Merge branch 'qcom-emac-pause'
Timur Tabi says:
====================
net: qcom/emac: ensure that pause frames are enabled
The qcom emac driver experiences significant packet loss (through frame
check sequence errors) if flow control is not enabled and the phy is
not configured to allow pause frames to pass through it. Therefore, we
need to enable flow control and force the phy to pass pause frames.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Timur Tabi [Mon, 7 Nov 2016 16:51:40 +0000 (10:51 -0600)]
net: qcom/emac: configure the external phy to allow pause frames
Pause frames are used to enable flow control. A MAC can send and
receive pause frames in order to throttle traffic. However, the PHY
must be configured to allow those frames to pass through.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Timur Tabi <timur@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Rafał Miłecki [Mon, 7 Nov 2016 12:53:27 +0000 (13:53 +0100)]
net: bgmac: fix reversed checks for clock control flag
This fixes regression introduced by patch adding feature flags. It was
already reported and patch followed (it got accepted) but it appears it
was incorrect. Instead of fixing reversed condition it broke a good one.
This patch was verified to actually fix SoC hanges caused by bgmac on
BCM47186B0.
Fixes: db791eb2970b ("net: ethernet: bgmac: convert to feature flags") Fixes: 4af1474e6198 ("net: bgmac: Fix errant feature flag check") Cc: Jon Mason <jon.mason@broadcom.com> Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
We received two reports of BUG_ON in bnad_txcmpl_process() where
hw_consumer_index appeared to be ahead of producer_index. Out of order
write/read of these variables could explain these reports.
bnad_start_xmit(), as a producer of tx descriptors, has a few memory
barriers sprinkled around writes to producer_index and the device's
doorbell but they're not paired with anything in bnad_txcmpl_process(), a
consumer.
Since we are synchronizing with a device, we must use mandatory barriers,
not smp_*. Also, I didn't see the purpose of the last smp_mb() in
bnad_start_xmit().
Signed-off-by: Benjamin Poirier <bpoirier@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net-ipv6: on device mtu change do not add mtu to mtu-less routes
Routes can specify an mtu explicitly or inherit the mtu from
the underlying device - this inheritance is implemented in
dst->ops->mtu handlers ip6_mtu() and ip6_blackhole_mtu().
Currently changing the mtu of a device adds mtu explicitly
to routes using that device.
ie.
# ip link set dev lo mtu 65536
# ip -6 route add local 2000::1 dev lo
# ip -6 route get 2000::1
local 2000::1 dev lo table local src ... metric 1024 pref medium
# ip link set dev lo mtu 65535
# ip -6 route get 2000::1
local 2000::1 dev lo table local src ... metric 1024 mtu 65535 pref medium
# ip link set dev lo mtu 65536
# ip -6 route get 2000::1
local 2000::1 dev lo table local src ... metric 1024 mtu 65536 pref medium
# ip -6 route del local 2000::1
After this patch the route entry no longer changes unless it already has an mtu.
There is no need: this inheritance is already done in ip6_mtu()
# ip link set dev lo mtu 65536
# ip -6 route add local 2000::1 dev lo
# ip -6 route add local 2000::2 dev lo mtu 2000
# ip -6 route get 2000::1; ip -6 route get 2000::2
local 2000::1 dev lo table local src ... metric 1024 pref medium
local 2000::2 dev lo table local src ... metric 1024 mtu 2000 pref medium
# ip link set dev lo mtu 65535
# ip -6 route get 2000::1; ip -6 route get 2000::2
local 2000::1 dev lo table local src ... metric 1024 pref medium
local 2000::2 dev lo table local src ... metric 1024 mtu 2000 pref medium
# ip link set dev lo mtu 1501
# ip -6 route get 2000::1; ip -6 route get 2000::2
local 2000::1 dev lo table local src ... metric 1024 pref medium
local 2000::2 dev lo table local src ... metric 1024 mtu 1501 pref medium
# ip link set dev lo mtu 65536
# ip -6 route get 2000::1; ip -6 route get 2000::2
local 2000::1 dev lo table local src ... metric 1024 pref medium
local 2000::2 dev lo table local src ... metric 1024 mtu 65536 pref medium
# ip -6 route del local 2000::1
# ip -6 route del local 2000::2
This is desirable because changing device mtu and then resetting it
to the previous value shouldn't change the user visible routing table.
Signed-off-by: Maciej Żenczykowski <maze@google.com> CC: Eric Dumazet <edumazet@google.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Do not send the next message in sendmmsg for partial sendmsg
invocations.
sendmmsg assumes that it can continue sending the next message
when the return value of the individual sendmsg invocations
is positive. It results in corrupting the data for TCP,
SCTP, and UNIX streams.
For example, sendmmsg([["abcd"], ["efgh"]]) can result in a stream
of "aefgh" if the first sendmsg invocation sends only the first
byte while the second sendmsg goes through.
Datagram sockets either send the entire datagram or fail, so
this patch affects only sockets of type SOCK_STREAM and
SOCK_SEQPACKET.
Fixes: 228e548e6020 ("net: Add sendmmsg socket system call") Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Neal Cardwell <ncardwell@google.com> Acked-by: Maciej Żenczykowski <maze@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gao Feng [Fri, 4 Nov 2016 02:28:49 +0000 (10:28 +0800)]
driver: macvlan: Destroy new macvlan port if macvlan_common_newlink failed.
When there is no existing macvlan port in lowdev, one new macvlan port
would be created. But it doesn't be destoried when something failed later.
It casues some memleak.
Now add one flag to indicate if new macvlan port is created.
Signed-off-by: Gao Feng <fgao@ikuai8.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Liping Zhang [Sun, 6 Nov 2016 06:40:01 +0000 (14:40 +0800)]
netfilter: nf_tables: fix oops when inserting an element into a verdict map
Dalegaard says:
The following ruleset, when loaded with 'nft -f bad.txt'
----snip----
flush ruleset
table ip inlinenat {
map sourcemap {
type ipv4_addr : verdict;
}
chain postrouting {
ip saddr vmap @sourcemap accept
}
}
add chain inlinenat test
add element inlinenat sourcemap { 100.123.10.2 : jump test }
----snip----
Nicolas Dichtel says:
After commit b87a2f9199ea ("netfilter: conntrack: add gc worker to
remove timed-out entries"), netlink conntrack deletion events may be
sent with a huge delay.
and indeed, this isn't optimal at all. Rationale here was to ensure that
we don't block other work items for too long, even if
nf_conntrack_htable_size is huge. But in order to have some guarantee
about maximum time period where a scan of the full conntrack table
completes we should always use a fixed slice size, so that once every
N scans the full table has been examined at least once.
We also need to balance this vs. the case where the system is either idle
(i.e., conntrack table (almost) empty) or very busy (i.e. eviction happens
from packet path).
So, after some discussion with Nicolas:
1. want hard guarantee that we scan entire table at least once every X s
-> need to scan fraction of table (get rid of upper bound)
2. don't want to eat cycles on idle or very busy system
-> increase interval if we did not evict any entries
3. don't want to block other worker items for too long
-> make fraction really small, and prefer small scan interval instead
4. Want reasonable short time where we detect timed-out entry when
system went idle after a burst of traffic, while not doing scans
all the time.
-> Store next gc scan in worker, increasing delays when no eviction
happened and shrinking delay when we see timed out entries.
The old gc interval is turned into a max number, scans can now happen
every jiffy if stale entries are present.
Longest possible time period until an entry is evicted is now 2 minutes
in worst case (entry expires right after it was deemed 'not expired').
Reported-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: Florian Westphal <fw@strlen.de> Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Florian Westphal [Sat, 29 Oct 2016 01:01:50 +0000 (03:01 +0200)]
netfilter: connmark: ignore skbs with magic untracked conntrack objects
The (percpu) untracked conntrack entries can end up with nonzero connmarks.
The 'untracked' conntrack objects are merely a way to distinguish INVALID
(i.e. protocol connection tracker says payload doesn't meet some
requirements or packet was never seen by the connection tracking code)
from packets that are intentionally not tracked (some icmpv6 types such as
neigh solicitation, or by using 'iptables -j CT --notrack' option).
Untracked conntrack objects are implementation detail, we might as well use
invalid magic address instead to tell INVALID and UNTRACKED apart.
Check skb->nfct for untracked dummy and behave as if skb->nfct is NULL.
Alexander Duyck [Fri, 4 Nov 2016 19:11:57 +0000 (15:11 -0400)]
fib_trie: Correct /proc/net/route off by one error
The display of /proc/net/route has had a couple issues due to the fact that
when I originally rewrote most of fib_trie I made it so that the iterator
was tracking the next value to use instead of the current.
In addition it had an off by 1 error where I was tracking the first piece
of data as position 0, even though in reality that belonged to the
SEQ_START_TOKEN.
This patch updates the code so the iterator tracks the last reported
position and key instead of the next expected position and key. In
addition it shifts things so that all of the leaves start at 1 instead of
trying to report leaves starting with offset 0 as being valid. With these
two issues addressed this should resolve any off by one errors that were
present in the display of /proc/net/route.
Fixes: 25b97c016b26 ("ipv4: off-by-one in continuation handling in /proc/net/route") Cc: Andy Whitcroft <apw@canonical.com> Reported-by: Jason Baron <jbaron@akamai.com> Tested-by: Jason Baron <jbaron@akamai.com> Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Add Qualcomm QCA tagging introduced in cafdc45c9 to the
list of supported protocols.
Signed-off-by: Fabian Mewes <architekt@coding4coffee.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Virtio 1.0 spec says VIRTIO_F_ANY_LAYOUT and VIRTIO_NET_F_GSO are
legacy-only feature bits. Do not negotiate them in virtio 1 mode. Note
this is a spec violation so we need to backport it to stable/downstream
kernels.
Cc: stable@vger.kernel.org Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 3 Nov 2016 23:17:26 +0000 (16:17 -0700)]
net: icmp6_send should use dst dev to determine L3 domain
icmp6_send is called in response to some event. The skb may not have
the device set (skb->dev is NULL), but it is expected to have a dst set.
Update icmp6_send to use the dst on the skb to determine L3 domain.
Fixes: ca254490c8dfd ("net: Add VRF support to IPv6 stack") Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Thu, 3 Nov 2016 23:56:31 +0000 (00:56 +0100)]
bpf: fix map not being uncharged during map creation failure
In map_create(), we first find and create the map, then once that
suceeded, we charge it to the user's RLIMIT_MEMLOCK, and then fetch
a new anon fd through anon_inode_getfd(). The problem is, once the
latter fails f.e. due to RLIMIT_NOFILE limit, then we only destruct
the map via map->ops->map_free(), but without uncharging the previously
locked memory first. That means that the user_struct allocation is
leaked as well as the accounted RLIMIT_MEMLOCK memory not released.
Make the label names in the fix consistent with bpf_prog_load().
Fixes: aaac3ba95e4c ("bpf: charge user for creation of BPF maps and programs") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Thu, 3 Nov 2016 23:01:19 +0000 (00:01 +0100)]
bpf: fix htab map destruction when extra reserve is in use
Commit a6ed3ea65d98 ("bpf: restore behavior of bpf_map_update_elem")
added an extra per-cpu reserve to the hash table map to restore old
behaviour from pre prealloc times. When non-prealloc is in use for a
map, then problem is that once a hash table extra element has been
linked into the hash-table, and the hash table is destroyed due to
refcount dropping to zero, then htab_map_free() -> delete_all_elements()
will walk the whole hash table and drop all elements via htab_elem_free().
The problem is that the element from the extra reserve is first fed
to the wrong backend allocator and eventually freed twice.
Fixes: a6ed3ea65d98 ("bpf: restore behavior of bpf_map_update_elem") Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
sctp_wait_for_connect() currently already holds the asoc to keep it
alive during the sleep, in case another thread release it. But Andrey
Konovalov and Dmitry Vyukov reported an use-after-free in such
situation.
Problem is that __sctp_connect() doesn't get a ref on the asoc and will
do a read on the asoc after calling sctp_wait_for_connect(), but by then
another thread may have closed it and the _put on sctp_wait_for_connect
will actually release it, causing the use-after-free.
Fix is, instead of doing the read after waiting for the connect, do it
before so, and avoid this issue as the socket is still locked by then.
There should be no issue on returning the asoc id in case of failure as
the application shouldn't trust on that number in such situations
anyway.
This issue doesn't exist in sctp_sendmsg() path.
Reported-by: Dmitry Vyukov <dvyukov@google.com> Reported-by: Andrey Konovalov <andreyknvl@google.com> Tested-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Reviewed-by: Xin Long <lucien.xin@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This series fixes a number of device reference leaks (and one of_node
leak) due to failure to drop the references taken by bus_find_device()
and friends.
Note that the final two patches have been compile tested only.
v2
- hold reference to cpsw-phy-sel device while accessing private data as
requested by David. Also update the commit message. (patch 1/4)
- add linux-omap on CC where appropriate
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to drop the references taken by bus_find_device() before
returning from emac_dev_open().
Note that phy_connect still takes a reference to the phy device.
Fixes: 5d69e0076a72 ("net: davinci_emac: switch to new mdio") Cc: Mugunthan V N <mugunthanvnm@ti.com> Cc: Grygorii Strashko <grygorii.strashko@ti.com> Cc: linux-omap@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hovold [Thu, 3 Nov 2016 17:40:20 +0000 (18:40 +0100)]
net: ethernet: ti: cpsw: fix device and of_node leaks
Make sure to drop the references taken by of_get_child_by_name() and
bus_find_device() before returning from cpsw_phy_sel().
Note that holding a reference to the cpsw-phy-sel device does not
prevent the devres-managed private data from going away.
Fixes: 5892cd135e16 ("drivers: net: cpsw-phy-sel: Add new driver...") Cc: Mugunthan V N <mugunthanvnm@ti.com> Cc: Grygorii Strashko <grygorii.strashko@ti.com> Cc: linux-omap@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hovold [Thu, 3 Nov 2016 17:40:19 +0000 (18:40 +0100)]
phy: fix device reference leaks
Make sure to drop the reference taken by bus_find_device_by_name()
before returning from phy_connect() and phy_attach().
Note that both function still take a reference to the phy device
through phy_attach_direct().
Fixes: e13934563db0 ("[PATCH] PHY Layer fixup") Cc: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
This series contains six hot fixes of the mlx5 core and mlx5e driver.
Huy fixed an invalid pointer dereference on initialization flow for when
the selected mlx5 load profile is out of range.
Or provided three eswitch offloads related fixes
- Prevent changing NS of a VF representor.
- Handle matching on vlan priority for offloaded TC rules
- Set the actions for offloaded rules properly
On my part I here addressed the error flow related issues in
mlx5e_open_channel reported by Jesper just this week.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Huy Nguyen [Thu, 3 Nov 2016 23:48:47 +0000 (01:48 +0200)]
net/mlx5: Fix invalid pointer reference when prof_sel parameter is invalid
When prof_sel is invalid, mlx5_core_warn is called but the
mlx5_core_dev is not initialized yet. Solution is moving the prof_sel code
after dev->pdev assignment
Fixes: 2974ab6e8bd8 ('net/mlx5: Improve driver log messages') Signed-off-by: Huy Nguyen <huyn@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Thu, 3 Nov 2016 23:48:46 +0000 (01:48 +0200)]
net/mlx5: E-Switch, Set the actions for offloaded rules properly
As for the current generation of the mlx5 HW (CX4/CX4-Lx) per flow vlan
push/pop actions are emulated, we must not program them to the firmware.
Fixes: f5f82476090f ('net/mlx5: E-Switch, Support VLAN actions in the offloads mode') Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Reported-by: Paul Blakey <paulb@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Thu, 3 Nov 2016 23:48:45 +0000 (01:48 +0200)]
net/mlx5e: Handle matching on vlan priority for offloaded TC rules
We ignored the vlan priority in offloaded TC rules matching part,
fix that.
Fixes: 095b6cfd69ce ('net/mlx5e: Add TC vlan match parsing') Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Reported-by: Paul Blakey <paulb@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Thu, 3 Nov 2016 23:48:44 +0000 (01:48 +0200)]
net/mlx5e: Disallow changing name-space for VF representors
VF reps should be altogether on the same NS as they were created.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Thu, 3 Nov 2016 23:48:42 +0000 (01:48 +0200)]
net/mlx5e: Fix XDP error path of mlx5e_open_channel()
In case of mlx5e_open_rq fails the error handling will jump to
label err_close_xdp_sq and will try to close the xdp_sq unconditionally.
xdp_sq is valid only in case of XDP use cases, i.e priv->xdp_prog is
not null.
To fix this in this patch we test xdp_sq validity prior to closing it.
In addition we now close the xdp_sq.cq as well.
Fixes: b5503b994ed5 ("net/mlx5e: XDP TX forwarding support") Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Reported-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
WANG Cong [Thu, 3 Nov 2016 16:42:36 +0000 (09:42 -0700)]
taskstats: fix the length of cgroupstats_cmd_get_policy
cgroupstats_cmd_get_policy is [CGROUPSTATS_CMD_ATTR_MAX+1],
taskstats_cmd_get_policy[TASKSTATS_CMD_ATTR_MAX+1],
but their family.maxattr is TASKSTATS_CMD_ATTR_MAX.
CGROUPSTATS_CMD_ATTR_MAX is less than TASKSTATS_CMD_ATTR_MAX,
so we could end up accessing out-of-bound.
Change cgroupstats_cmd_get_policy to TASKSTATS_CMD_ATTR_MAX+1,
this is safe because the rest are initialized to 0's.
Reported-by: Andrey Konovalov <andreyknvl@google.com> Tested-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
WANG Cong [Thu, 3 Nov 2016 16:42:35 +0000 (09:42 -0700)]
genetlink: fix a memory leak on error path
In __genl_register_family(), when genl_validate_assign_mc_groups()
fails, we forget to free the memory we possibly allocate for
family->attrbuf.
Note, some callers call genl_unregister_family() to clean up
on error path, it doesn't work because the family is inserted
to the global list in the nearly last step.
Cc: Jakub Kicinski <kubakici@wp.pl> Cc: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 3 Nov 2016 15:59:46 +0000 (08:59 -0700)]
ipv6: dccp: add missing bind_conflict to dccp_ipv6_mapped
While fuzzing kernel with syzkaller, Andrey reported a nasty crash
in inet6_bind() caused by DCCP lacking a required method.
Fixes: ab1e0a13d7029 ("[SOCK] proto: Add hashinfo member to struct proto") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Andrey Konovalov <andreyknvl@google.com> Tested-by: Andrey Konovalov <andreyknvl@google.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the ehea driver is missing a call to netif_carrier_off()
before the interface bring-up; this is necessary in order to
initialize the __LINK_STATE_NOCARRIER bit in the net_device state
field. Otherwise, we observe state UNKNOWN on "ip address" command
output.
This patch adds a call to netif_carrier_off() on ehea's net device
open callback.
Reported-by: Xiong Zhou <zhou@redhat.com>
Reference-ID: IBM bz #137702, Red Hat bz #1089134 Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com> Signed-off-by: Douglas Miller <dougmill@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 3 Nov 2016 03:21:20 +0000 (20:21 -0700)]
netlink: netlink_diag_dump() runs without locks
A recent commit removed locking from netlink_diag_dump() but forgot
one error case.
=====================================
[ BUG: bad unlock balance detected! ]
4.9.0-rc3+ #336 Not tainted
-------------------------------------
syz-executor/4018 is trying to release lock ([ 36.220068] nl_table_lock
) at:
[<ffffffff82dc8683>] netlink_diag_dump+0x1a3/0x250 net/netlink/diag.c:182
but there are no more locks to release!
other info that might help us debug this:
3 locks held by syz-executor/4018:
#0: [ 36.220068] (
sock_diag_mutex[ 36.220068] ){+.+.+.}
, at: [ 36.220068] [<ffffffff82c3873b>] sock_diag_rcv+0x1b/0x40
#1: [ 36.220068] (
sock_diag_table_mutex[ 36.220068] ){+.+.+.}
, at: [ 36.220068] [<ffffffff82c38e00>] sock_diag_rcv_msg+0x140/0x3a0
#2: [ 36.220068] (
nlk->cb_mutex[ 36.220068] ){+.+.+.}
, at: [ 36.220068] [<ffffffff82db6600>] netlink_dump+0x50/0xac0
Fixes: ad202074320c ("netlink: Use rhashtable walk interface in diag dump") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Andrey Konovalov <andreyknvl@google.com> Tested-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 3 Nov 2016 02:00:40 +0000 (19:00 -0700)]
dccp: fix out of bound access in dccp_v4_err()
dccp_v4_err() does not use pskb_may_pull() and might access garbage.
We only need 4 bytes at the beginning of the DCCP header, like TCP,
so the 8 bytes pulled in icmp_socket_deliver() are more than enough.
This patch might allow to process more ICMP messages, as some routers
are still limiting the size of reflected bytes to 28 (RFC 792), instead
of extended lengths (RFC 1812 4.3.2.3)
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fix this the same way we did for TCP in commit 565b7b2d2e63
("tcp: do not send reset to already closed sockets")
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Andrey Konovalov <andreyknvl@google.com> Tested-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
It turns out DCCP calls __sk_receive_skb(), and this broke when
lookups no longer took a reference on listeners.
Fix this issue by adding a @refcounted parameter to __sk_receive_skb(),
so that sock_put() is used only when needed.
Fixes: 3b24d854cb35 ("tcp/dccp: do not touch listener sk_refcnt under synflood") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Andrey Konovalov <andreyknvl@google.com> Tested-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ipv4: allow local fragmentation in ip_finish_output_gso()
Some configurations (e.g. geneve interface with default
MTU of 1500 over an ethernet interface with 1500 MTU) result
in the transmission of packets that exceed the configured MTU.
While this should be considered to be a "bad" configuration,
it is still allowed and should not result in the sending
of packets that exceed the configured MTU.
Fix by dropping the assumption in ip_finish_output_gso() that
locally originated gso packets will never need fragmentation.
Basic testing using iperf (observing CPU usage and bandwidth)
have shown no measurable performance impact for traffic not
requiring fragmentation.
Fixes: c7ba65d7b649 ("net: ip: push gso skb forwarding handling down the stack") Reported-by: Jan Tluka <jtluka@redhat.com> Signed-off-by: Lance Richardson <lrichard@redhat.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
MD5 has a code path that calls __inet_lookup_listener with a null skb,
so inet{6}_exact_dif_match needs to check skb against null before pulling
the flag.
Fixes: a04a480d4392 ("net: Require exact match for TCP socket lookups if
dif is l3mdev") Reported-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Tested-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 2 Nov 2016 14:53:17 +0000 (07:53 -0700)]
tcp: fix potential memory corruption
Imagine initial value of max_skb_frags is 17, and last
skb in write queue has 15 frags.
Then max_skb_frags is lowered to 14 or smaller value.
tcp_sendmsg() will then be allowed to add additional page frags
and eventually go past MAX_SKB_FRAGS, overflowing struct
skb_shared_info.
Fixes: 5f74f82ea34c ("net:Add sysctl_max_skb_frags") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Hans Westgaard Ry <hans.westgaard.ry@oracle.com> Cc: Håkon Bugge <haakon.bugge@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mintz, Yuval [Wed, 2 Nov 2016 14:36:46 +0000 (16:36 +0200)]
qede: Correctly map aggregation replacement pages
Driver allocates replacement buffers before-hand to make
sure whenever an aggregation begins there would be a replacement
for the Rx buffers, as we can't release the buffer until
aggregation is terminated and driver logic assumes the Rx rings
are always full.
For every other Rx page that's being allocated [I.e., regular]
the page is being completely mapped while for the replacement
buffers only the first portion of the page is being mapped.
This means that:
a. Once replacement buffer replenishes the regular Rx ring,
assuming there's more than a single packet on page we'd post unmapped
memory toward HW [assuming mapping is actually done in granularity
smaller than page].
b. Unmaps are being done for the entire page, which is incorrect.
Fixes: 55482edc25f06 ("qede: Add slowpath/fastpath support and enable hardware GRO") Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike commit 26cabd31259ba43f68026ce3f62b78094124333f
("sched, net: Clean up sk_wait_event() vs. might_sleep()"), the
sleeping function is called before schedule_timeout(), this is indeed
a bug. Fix this by moving the wait logic to the new API, it is similar
to commit ff960a731788a7408b6f66ec4fd772ff18833211
("netdev, sched/wait: Fix sleeping inside wait event").
Reported-by: Andrey Konovalov <andreyknvl@google.com> Cc: Andrey Konovalov <andreyknvl@google.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dongli Zhang [Wed, 2 Nov 2016 01:04:33 +0000 (09:04 +0800)]
xen-netfront: cast grant table reference first to type int
IS_ERR_VALUE() in commit 87557efc27f6a50140fb20df06a917f368ce3c66
("xen-netfront: do not cast grant table reference to signed short") would
not return true for error code unless we cast ref first to type int.
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eli Cooper [Tue, 1 Nov 2016 15:45:13 +0000 (23:45 +0800)]
ip6_udp_tunnel: remove unused IPCB related codes
Some IPCB fields are currently set in udp_tunnel6_xmit_skb(), which are
never used before it reaches ip6tunnel_xmit(), and past that point the
control buffer is no longer interpreted as IPCB.
This clears these unused IPCB related codes. Currently there is no skb
scrubbing in ip6_udp_tunnel, otherwise IPCB(skb)->opt might need to be
cleared for IPv4 packets, as shown in 5146d1f1511
("tunnel: Clear IPCB(skb)->opt before dst_link_failure called").
Signed-off-by: Eli Cooper <elicooper@gmx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eli Cooper [Tue, 1 Nov 2016 15:45:12 +0000 (23:45 +0800)]
ip6_tunnel: Clear IP6CB in ip6tunnel_xmit()
skb->cb may contain data from previous layers. In the observed scenario,
the garbage data were misinterpreted as IP6CB(skb)->frag_max_size, so
that small packets sent through the tunnel are mistakenly fragmented.
This patch unconditionally clears the control buffer in ip6tunnel_xmit(),
which affects ip6_tunnel, ip6_udp_tunnel and ip6_gre. Currently none of
these tunnels set IP6CB(skb)->flags, otherwise it needs to be done earlier.
Cc: stable@vger.kernel.org Signed-off-by: Eli Cooper <elicooper@gmx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This occurs due to rounding errors when calculating the microseconds
value - the divisons round down. This causes (eg) the rx-usecs to
decrease by one every time the tx-usecs value is set as per the above.
Fix this by making the divison round-to-nearest.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
'create_root_ns()' does not return an error pointer, so the test can be
simplified to be more consistent.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Acked-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Isaac Boukris [Tue, 1 Nov 2016 00:41:35 +0000 (02:41 +0200)]
unix: escape all null bytes in abstract unix domain socket
Abstract unix domain socket may embed null characters,
these should be translated to '@' when printed out to
proc the same way the null prefix is currently being
translated.
This helps for tools such as netstat, lsof and the proc
based implementation in ss to show all the significant
bytes of the name (instead of getting cut at the first
null occurrence).
Signed-off-by: Isaac Boukris <iboukris@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
1. Since ethernet v1 hardware has a bug related to coalescing,
disabling this feature
2. Fixing ethernet v2 hardware, interrupt trigger region
id to 2, to kickoff coalescing
====================
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 1 Nov 2016 01:01:03 +0000 (21:01 -0400)]
Merge tag 'linux-can-fixes-for-4.9-20161031' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2016-10-31
this is a pull request of two patches for the upcoming v4.9 release.
The first patch is by Lukas Resch for the sja1000 plx_pci driver that adds
support for Moxa CAN devices. The second patch is by Oliver Hartkopp and fixes
a potential kernel panic in the CAN broadcast manager.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Gospodarek [Mon, 31 Oct 2016 17:32:03 +0000 (13:32 -0400)]
bgmac: stop clearing DMA receive control register right after it is set
Current bgmac code initializes some DMA settings in the receive control
register for some hardware and then immediately clears those settings.
Not clearing those settings results in ~420Mbps *improvement* in
throughput; this system can now receive frames at line-rate on Broadcom
5871x hardware compared to ~520Mbps today. I also tested a few other
values but found there to be no discernible difference in CPU
utilization even if burst size and prefetching values are different.
On the hardware tested there was no need to keep the code that cleared
all but bits 16-17, but since there is a wide variety of hardware that
used this driver (I did not look at all hardware docs for hardware using
this IP block), I find it wise to move this call up and clear bits just
after reading the default value from the hardware rather than completely
removing it.
This is a good candidate for -stable >=3.14 since that is when the code
that was supposed to improve performance (but did not) was introduced.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com> Fixes: 56ceecde1f29 ("bgmac: initialize the DMA controller of core...") Cc: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Mon, 31 Oct 2016 12:32:33 +0000 (20:32 +0800)]
sctp: hold transport instead of assoc when lookup assoc in rx path
Prior to this patch, in rx path, before calling lock_sock, it needed to
hold assoc when got it by __sctp_lookup_association, in case other place
would free/put assoc.
But in __sctp_lookup_association, it lookup and hold transport, then got
assoc by transport->assoc, then hold assoc and put transport. It means
it didn't hold transport, yet it was returned and later on directly
assigned to chunk->transport.
Without the protection of sock lock, the transport may be freed/put by
other places, which would cause a use-after-free issue.
This patch is to fix this issue by holding transport instead of assoc.
As holding transport can make sure to access assoc is also safe, and
actually it looks up assoc by searching transport rhashtable, to hold
transport here makes more sense.
Note that the function will be renamed later on on another patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Mon, 31 Oct 2016 12:32:32 +0000 (20:32 +0800)]
sctp: return back transport in __sctp_rcv_init_lookup
Prior to this patch, it used a local variable to save the transport that is
looked up by __sctp_lookup_association(), and didn't return it back. But in
sctp_rcv, it is used to initialize chunk->transport. So when hitting this,
even if it found the transport, it was still initializing chunk->transport
with null instead.
This patch is to return the transport back through transport pointer
that is from __sctp_rcv_lookup_harder().
Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Mon, 31 Oct 2016 12:32:31 +0000 (20:32 +0800)]
sctp: hold transport instead of assoc in sctp_diag
In sctp_transport_lookup_process(), Commit 1cceda784980 ("sctp: fix
the issue sctp_diag uses lock_sock in rcu_read_lock") moved cb() out
of rcu lock, but it put transport and hold assoc instead, and ignore
that cb() still uses transport. It may cause a use-after-free issue.
This patch is to hold transport instead of assoc there.
Fixes: 1cceda784980 ("sctp: fix the issue sctp_diag uses lock_sock in rcu_read_lock") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Oliver Hartkopp [Mon, 24 Oct 2016 19:11:26 +0000 (21:11 +0200)]
can: bcm: fix warning in bcm_connect/proc_register
Andrey Konovalov reported an issue with proc_register in bcm.c.
As suggested by Cong Wang this patch adds a lock_sock() protection and
a check for unsuccessful proc_create_data() in bcm_connect().
David S. Miller [Mon, 31 Oct 2016 19:37:30 +0000 (15:37 -0400)]
Merge tag 'wireless-drivers-for-davem-2016-10-30' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.9
iwlwifi
* some fixes for suspend/resume with unified FW images
* a fix for a false-positive lockdep report
* a fix for multi-queue that caused an unnecessary 1 second latency
* a fix for an ACPI parsing bug that caused a misleading error message
brcmfmac
* fix a variable uninitialised warning in brcmf_cfg80211_start_ap()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Sun, 30 Oct 2016 09:09:22 +0000 (10:09 +0100)]
mlxsw: spectrum: Fix incorrect reuse of MID entries
In the device, a MID entry represents a group of local ports, which can
later be bound to a MDB entry.
The lookup of an existing MID entry is currently done using the provided
MC MAC address and VID, from the Linux bridge. However, this can result
in an incorrect reuse of the same MID index in different VLAN-unaware
bridges (same IP MC group and VID 0).
Fix this by performing the lookup based on FID instead of VID, which is
unique across different bridges.
Fixes: 3a49b4fde2a1 ("mlxsw: Adding layer 2 multicast support") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Acked-by: Elad Raz <eladr@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mintz, Yuval [Sun, 30 Oct 2016 08:25:42 +0000 (10:25 +0200)]
qede: Fix statistics' strings for Tx/Rx queues
When an interface is configured to use Tx/Rx-only queues,
the length of the statistics would be shortened to accomodate only the
statistics required per-each queue, and the values would be provided
accordingly.
However, the strings provided would still contain both Tx and Rx strings
for each one of the queues [regardless of its configuration], which might
lead to out-of-bound access when filling the buffers as well as incorrect
statistics presented.
Fixes: 9a4d7e86acf3 ("qede: Add support for Tx/Rx-only queues.") Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 29 Oct 2016 18:02:36 +0000 (11:02 -0700)]
net: mangle zero checksum in skb_checksum_help()
Sending zero checksum is ok for TCP, but not for UDP.
UDPv6 receiver should by default drop a frame with a 0 checksum,
and UDPv4 would not verify the checksum and might accept a corrupted
packet.
Simply replace such checksum by 0xffff, regardless of transport.
This error was caught on SIT tunnels, but seems generic.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Willem de Bruijn <willemb@google.com> Acked-by: Maciej Żenczykowski <maze@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 28 Oct 2016 20:40:24 +0000 (13:40 -0700)]
net: clear sk_err_soft in sk_clone_lock()
At accept() time, it is possible the parent has a non zero
sk_err_soft, leftover from a prior error.
Make sure we do not leave this value in the child, as it
makes future getsockopt(SO_ERROR) calls quite unreliable.
Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
... which makes sense for reno (it sets ssthresh to half the current cwnd),
but it makes no sense for dctcp, which sets ssthresh based on the current
congestion estimate.
This can cause severe growth of cwnd (eventually overflowing u32).
Fix this by saving last cwnd on loss and restore cwnd based on that,
similar to cubic and other algorithms.
Fixes: e3118e8359bb7c ("net: tcp: add DCTCP congestion control algorithm") Cc: Lawrence Brakmo <brakmo@fb.com> Cc: Andrew Shewmaker <agshew@gmail.com> Cc: Glenn Judd <glenn.judd@morganstanley.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Fri, 28 Oct 2016 10:18:01 +0000 (18:18 +0800)]
ipv6: add mtu lock check in __ip6_rt_update_pmtu
Prior to this patch, ipv6 didn't do mtu lock check in ip6_update_pmtu.
It leaded to that mtu lock doesn't really work when receiving the pkt
of ICMPV6_PKT_TOOBIG.
This patch is to add mtu lock check in __ip6_rt_update_pmtu just as ipv4
did in __ip_rt_update_pmtu.
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Sitnicki [Wed, 26 Oct 2016 09:21:14 +0000 (11:21 +0200)]
ipv6: Don't use ufo handling on later transformed packets
Similar to commit c146066ab802 ("ipv4: Don't use ufo handling on later
transformed packets"), don't perform UFO on packets that will be IPsec
transformed. To detect it we rely on the fact that headerlen in
dst_entry is non-zero only for transformation bundles (xfrm_dst
objects).
Unwanted segmentation can be observed with a NETIF_F_UFO capable device,
such as a dummy device:
DEV=dum0 LEN=1493
ip li add $DEV type dummy
ip addr add fc00::1/64 dev $DEV nodad
ip link set $DEV up
ip xfrm policy add dir out src fc00::1 dst fc00::2 \
tmpl src fc00::1 dst fc00::2 proto esp spi 1
ip xfrm state add src fc00::1 dst fc00::2 \
proto esp spi 1 enc 'aes' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b
Fixes: e89e9cf539a2 ("[IPv4/IPv6]: UFO Scatter-gather approach") Signed-off-by: Jakub Sitnicki <jkbs@redhat.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Liping Zhang [Sat, 29 Oct 2016 14:03:05 +0000 (22:03 +0800)]
netfilter: nf_tables: destroy the set if fail to add transaction
When the memory is exhausted, then we will fail to add the NFT_MSG_NEWSET
transaction. In such case, we should destroy the set before we free it.
Fixes: 958bee14d071 ("netfilter: nf_tables: use new transaction infrastructure to handle sets") Signed-off-by: Liping Zhang <zlpnobody@gmail.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Mark Lord [Sun, 30 Oct 2016 23:28:27 +0000 (19:28 -0400)]
r8152: Fix broken RX checksums.
The r8152 driver has been broken since (approx) 3.16.xx
when support was added for hardware RX checksums
on newer chip versions. Symptoms include random
segfaults and silent data corruption over NFS.
The hardware checksum logig does not work on the VER_02
dongles I have here when used with a slow embedded system CPU.
Google reveals others reporting similar issues on Raspberry Pi.
So, disable hardware RX checksum support for VER_02, and fix
an obvious coding error for IPV6 checksums in the same function.
Because this bug results in silent data corruption,
it is a good candidate for back-porting to -stable >= 3.16.xx.
Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Lots of fixes, mostly drivers as is usually the case.
1) Don't treat zero DMA address as invalid in vmxnet3, from Alexey
Khoroshilov.
2) Fix element timeouts in netfilter's nft_dynset, from Anders K.
Pedersen.
3) Don't put aead_req crypto struct on the stack in mac80211, from
Ard Biesheuvel.
4) Several uninitialized variable warning fixes from Arnd Bergmann.
5) Fix memory leak in cxgb4, from Colin Ian King.
6) Fix bpf handling of VLAN header push/pop, from Daniel Borkmann.
7) Several VRF semantic fixes from David Ahern.
8) Set skb->protocol properly in ip6_tnl_xmit(), from Eli Cooper.
9) Socket needs to be locked in udp_disconnect(), from Eric Dumazet.
10) Div-by-zero on 32-bit fix in mlx4 driver, from Eugenia Emantayev.
11) Fix stale link state during failover in NCSCI driver, from Gavin
Shan.
12) Fix netdev lower adjacency list traversal, from Ido Schimmel.
13) Propvide proper handle when emitting notifications of filter
deletes, from Jamal Hadi Salim.
14) Memory leaks and big-endian issues in rtl8xxxu, from Jes Sorensen.
15) Fix DESYNC_FACTOR handling in ipv6, from Jiri Bohac.
16) Several routing offload fixes in mlxsw driver, from Jiri Pirko.
17) Fix broadcast sync problem in TIPC, from Jon Paul Maloy.
18) Validate chunk len before using it in SCTP, from Marcelo Ricardo
Leitner.
19) Revert a netns locking change that causes regressions, from Paul
Moore.
20) Add recursion limit to GRO handling, from Sabrina Dubroca.
21) GFP_KERNEL in irq context fix in ibmvnic, from Thomas Falcon.
22) Avoid accessing stale vxlan/geneve socket in data path, from
Pravin Shelar"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (189 commits)
geneve: avoid using stale geneve socket.
vxlan: avoid using stale vxlan socket.
qede: Fix out-of-bound fastpath memory access
net: phy: dp83848: add dp83822 PHY support
enic: fix rq disable
tipc: fix broadcast link synchronization problem
ibmvnic: Fix missing brackets in init_sub_crq_irqs
ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt context
Revert "ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt context"
arch/powerpc: Update parameters for csum_tcpudp_magic & csum_tcpudp_nofold
net/mlx4_en: Save slave ethtool stats command
net/mlx4_en: Fix potential deadlock in port statistics flow
net/mlx4: Fix firmware command timeout during interrupt test
net/mlx4_core: Do not access comm channel if it has not yet been initialized
net/mlx4_en: Fix panic during reboot
net/mlx4_en: Process all completions in RX rings after port goes up
net/mlx4_en: Resolve dividing by zero in 32-bit system
net/mlx4_core: Change the default value of enable_qos
net/mlx4_core: Avoid setting ports to auto when only one port type is supported
net/mlx4_core: Fix the resource-type enum in res tracker to conform to FW spec
...
pravin shelar [Fri, 28 Oct 2016 16:59:16 +0000 (09:59 -0700)]
geneve: avoid using stale geneve socket.
This patch is similar to earlier vxlan patch.
Geneve device close operation frees geneve socket. This
operation can race with geneve-xmit function which
dereferences geneve socket. Following patch uses RCU
mechanism to avoid this situation.
Signed-off-by: Pravin B Shelar <pshelar@ovn.org> Acked-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
pravin shelar [Fri, 28 Oct 2016 16:59:15 +0000 (09:59 -0700)]
vxlan: avoid using stale vxlan socket.
When vxlan device is closed vxlan socket is freed. This
operation can race with vxlan-xmit function which
dereferences vxlan socket. Following patch uses RCU
mechanism to avoid this situation.
Signed-off-by: Pravin B Shelar <pshelar@ovn.org> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-kernels.git / log