The SCSI PRE-FETCH (10 or 16) command is present both on hard disks
and some SSDs. It is useful when the address of the next block(s) to
be read is known but it is not following the LBA of the current READ
(so read-ahead won't help). It returns two "good" SCSI Status values.
If the requested blocks have fitted (or will most likely fit (when
the IMMED bit is set)) into the disk's cache, it returns CONDITION
MET. If it didn't (or will not) fit then it returns GOOD status.
The goal of this patch is to stop the SCSI subsystem treating the
CONDITION MET SCSI status as an error. The current state makes the
PRE-FETCH command effectively unusable via pass-throughs.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com> Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If a recursive IOP_RESET is invoked, usually due to the eh_thread
handling errors after the first reset, be sure we flag that the command
thread has been stopped to avoid an Oops of the form;
iscsi tcp will first send out data, then calculate and send data
digest. If we don't have BDI_CAP_STABLE_WRITES, the page cache will be
written in spite of the on going writeback. Consequently, wrong digest
will be got and sent to target.
To fix this, set BDI_CAP_STABLE_WRITES when data digest is enabled
in iscsi_tcp .slave_configure callback.
Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com> Acked-by: Chris Leech <cleech@redhat.com> Acked-by: Lee Duncan <lduncan@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This commit reads the disk's old state and combines it with the device
disk-reported state rather than unconditionally marking it as RW.
Reported-by: Li Ning <lining916740672@icloud.com> Signed-off-by: Jeremy Cline <jeremy@jcline.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The firmware event workqueue should not be marked as WQ_MEM_RECLAIM
as it's doesn't need to make forward progress under memory pressure.
In the current state it will result in a deadlock if the device had been
forcefully removed.
Cc: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com> Acked-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com> Signed-off-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
and that assumes shost has been assigned with pci_set_drvdata().
However, pci_set_drvdata(pdev, shost) is done in aac_probe_one() far
after bailing out with error from calling the init function
((*aac_drivers[index].init)(aac)), and when the init function fails, no
error is returned from aac_probe_one() so PCI layer assumes there is
driver attached, and tries to shut it down later.
Fix it by returning error from aac_probe_one() when card-specific init
function fails.
This fixes reboot on my HP NetRAID-4M with dead battery.
Signed-off-by: Meelis Roos <mroos@linux.ee> Reviewed-by: Dave Carroll <david.carroll@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The data in NVRAM is not guaranteed to be NUL terminated. Since
snprintf expects byte-stream to accommodate null byte, the CHAP secret
is truncated. Use sprintf instead of snprintf to fix the truncation of
CHAP name and secret.
Signed-off-by: Andrew Vasquez <andrew.vasquez@cavium.com> Signed-off-by: Nilesh Javali <nilesh.javali@cavium.com> Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com> Acked-by: Chris Leech <cleech@redhat.com> Acked-by: Lee Duncan <lduncan@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Increase cmd_per_lun to allow more I/Os in progress per device,
particularly for NVMe's. The Hyper-V host side can handle the higher
count with no issues.
Signed-off-by: Michael Kelley <mikelley@microsoft.com> Reviewed-by: K. Y. Srinivasan <kys@microsoft.com> Acked-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We wanted to exit the loop with "div" set to zero, but instead, if we
don't hit the break then "div" is -1 when we finish the loop. It leads
to an array underflow a few lines later.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Acked-by: Matthew Wilcox <mawilcox@microsoft.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When a request times out we set the io_req flag BNX2FC_FLAG_IO_COMPL so
that if a subsequent completion comes in on that task ID we will ignore
it. The issue is that in the check for this flag there is a missing
return so we will continue to process a request which may have already
been returned to the ownership of the SCSI layer. This can cause
unpredictable results.
Solution is to add in the missing return.
[mkp: typo plus title shortening]
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com> Reviewed-by: Laurence Oberman <loberman@redhat.com> Tested-by: Laurence Oberman <loberman@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
cpu_msix_table is allocated to store online cpus, but pci_irq_get_affinity
may return cpu_possible_mask which is then used to access cpu_msix_table.
That causes bad user experience. Fix limits access to only online cpus,
I've also added an additional test to protect from an unlikely change in
cpu_online_mask.
[mkp: checkpatch]
Fixes: 1d55abc0e98a ("scsi: mpt3sas: switch to pci_alloc_irq_vectors") Signed-off-by: Tomas Henzl <thenzl@redhat.com> Acked-by: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When exiting a transformation, the cra_exit() helper is called in each
driver providing one. The Inside Secure SafeXcel driver has one, which
is responsible of freeing some areas and of sending one invalidation
request to the crypto engine, to invalidate the context that was used
during the transformation.
We could see in some setups (when lots of transformations were being
used with a short lifetime, and hence lots of cra_exit() calls) NULL
pointer dereferences and other weird issues. All these issues were
coming from accessing the tfm context.
The issue is the invalidation request completion is checked using a
wait_for_completion_interruptible() call in both the cipher and hash
cra_exit() helpers. In some cases this was interrupted while the
invalidation request wasn't processed yet. And then cra_exit() returned,
and its caller was freeing the tfm instance. Only then the request was
being handled by the SafeXcel driver, which lead to the said issues.
This patch fixes this by using wait_for_completion() calls in these
specific cases.
This patch fixes the extra cache computation when the queued data is a
multiple of a block size. This fixes the hash support in some cases.
Fixes: 809778e02cd4 ("crypto: inside-secure - fix hash when length is a multiple of a block") Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This patch fixes the cache length computation as cache_len could end up
being a negative value. The check between the queued size and the
block size is updated to reflect the caching mechanism which can cache
up to a full block size (included!).
Fixes: 809778e02cd4 ("crypto: inside-secure - fix hash when length is a multiple of a block") Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This patch adds a check in the SafeXcel dequeue function, to avoid
processing request further if no hardware command was issued. This can
happen in certain cases where the ->send() function caches all the data
that would have been send.
Fixes: 809778e02cd4 ("crypto: inside-secure - fix hash when length is a multiple of a block") Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
I don't why we need take a single write lock and disable interrupts
while setting up debugfs. This is what what happens when we try anyway:
|ccp 0000:03:00.2: enabling device (0000 -> 0002)
|BUG: sleeping function called from invalid context at kernel/locking/rwsem.c:69
|in_atomic(): 1, irqs_disabled(): 1, pid: 3, name: kworker/0:0
|irq event stamp: 17150
|hardirqs last enabled at (17149): [<0000000097a18c49>] restore_regs_and_return_to_kernel+0x0/0x23
|hardirqs last disabled at (17150): [<000000000773b3a9>] _raw_write_lock_irqsave+0x1b/0x50
|softirqs last enabled at (17148): [<0000000064d56155>] __do_softirq+0x3b8/0x4c1
|softirqs last disabled at (17125): [<0000000092633c18>] irq_exit+0xb1/0xc0
|CPU: 0 PID: 3 Comm: kworker/0:0 Not tainted 4.16.0-rc2+ #30
|Workqueue: events work_for_cpu_fn
|Call Trace:
| dump_stack+0x7d/0xb6
| ___might_sleep+0x1eb/0x250
| down_write+0x17/0x60
| start_creating+0x4c/0xe0
| debugfs_create_dir+0x9/0x100
| ccp5_debugfs_setup+0x191/0x1b0
| ccp5_init+0x8a7/0x8c0
| ccp_dev_init+0xb8/0xe0
| sp_init+0x6c/0x90
| sp_pci_probe+0x26e/0x590
| local_pci_probe+0x3f/0x90
| work_for_cpu_fn+0x11/0x20
| process_one_work+0x1ff/0x650
| worker_thread+0x1d4/0x3a0
| kthread+0xfe/0x130
| ret_from_fork+0x27/0x50
If any locking is required, a simple mutex will do it.
Cc: Gary R Hook <gary.hook@amd.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: Gary R Hook <gary.hook@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The Atmel AES driver uses memzero_explicit on the keys on error, but the
variable zeroed isn't the right one because of a typo. Fix this by using
the right variable.
Fixes: 89a82ef87e01 ("crypto: atmel-authenc - add support to authenc(hmac(shaX), Y(aes)) modes") Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This patch updates the safexcel_hmac_init_pad() function to also wait
for completion when the digest return code is -EBUSY, as it would mean
the request is in the backlog to be processed later.
Commit 8f18c8a48b73 ("staging: lustre: lmv: separate master object
with master stripe") changed how lmo_root inodes were managed,
particularly when LMV_HASH_FLAG_MIGRATION is not set.
Previously lsm_md_oinfo[0].lmo_root was always a borrowed
inode reference and didn't need to by iput().
Since the change, that special case only applies when
LMV_HASH_FLAG_MIGRATION is set
In the upstream (lustre-release) version of this patch [Commit 60e07b972114 ("LU-4690 lod: separate master object with master
stripe")] the for loop in the lmv_unpack_md() was changed to count
from 0 and to ignore entry 0 if LMV_HASH_FLAG_MIGRATION is set.
In the patch that got applied to Linux, that change was missing,
so lsm_md_oinfo[0].lmo_root is never iput().
This results in a "VFS: Busy inodes" warning at unmount.
Fixes: 8f18c8a48b73 ("staging: lustre: lmv: separate master object with master stripe") Signed-off-by: NeilBrown <neilb@suse.com> Reviewed-by: James Simmons <jsimmons@infradead.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The case statement in get_ap_information() should not use literal integers
to parse information element IDs when these values are provided by name
in 'enum ieee80211_eid' in the header 'linux/ieee80211.h'.
Currently the allocation of priv->oldaddr is not null checked which will
lead to subsequent errors when accessing priv->oldaddr. Fix this with
a null pointer check and a return of -ENOMEM on allocation failure.
Detected with Coccinelle:
drivers/staging/rtl8192u/r8192U_core.c:1708:2-15: alloc with no test,
possible model on line 1723
Fixes: 8fc8598e61f6 ("Staging: Added Realtek rtl8192u driver to staging") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Hauppauge em28xx bulk devices exhibit continuity errors and corrupted
packets, when run in VMWare virtual machines. Unknown if other
manufacturers bulk models exhibit the same issue. KVM/Qemu is unaffected.
According to documentation the maximum packet multiplier for em28xx in bulk
transfer mode is 256 * 188 bytes. This changes the size of bulk transfers
to maximum supported value and have a bonus beneficial alignment.
Before:
After:
This sets up USB to expect just as many bytes as the em28xx is set to emit.
Successful usage under load afterwards natively and in both VMWare
and KVM/Qemu virtual machines.
Signed-off-by: Brad Love <brad@nextdimension.cc> Reviewed-by: Michael Ira Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When used as an i2c device there is a module usage count mismatch on
removal, preventing the driver from being used thereafter. dvb_attach
increments the usage count so it is properly balanced on removal.
When handling an OS descriptor request, one of the first operations is
to zero out the request buffer using the wLength from the setup packet.
There is no bounds checking, so a wLength > 4096 would clobber memory
adjacent to the request buffer. Fix this by taking the min of wLength
and the request buffer length prior to the memset. While at it, define
the buffer length in a header file so that magic numbers don't appear
throughout the code.
When returning data to the host, the data length should be the min of
the wLength and the valid data we have to return. Currently we are
returning wLength, thus requests for a wLength greater than the amount
of data in the OS descriptor buffer would return invalid (albeit zero'd)
data following the valid descriptor data. Fix this by counting the
number of bytes when constructing the data and using this when
determining the length of the request.
Signed-off-by: Chris Dickens <christopher.a.dickens@gmail.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When using a AIO read() operation on the function FS gadget driver a URB is
submitted asynchronously and on URB completion the received data is copied
to the userspace buffer associated with the read operation.
This is done from a kernel worker thread invoking copy_to_user() (through
copy_to_iter()). And while the user space process memory is made available
to the kernel thread using use_mm(), some architecture require in addition
to this that the operation runs with USER_DS set. Otherwise the userspace
memory access will fail.
For example on ARM64 with Privileged Access Never (PAN) and User Access
Override (UAO) enabled the following crash occurs.
Internal error: Accessing user space memory with fs=KERNEL_DS: 9600004f [#1] SMP
Modules linked in:
CPU: 2 PID: 1636 Comm: kworker/2:1 Not tainted 4.9.0-04081-g8ab2dfb-dirty #487
Hardware name: ZynqMP ZCU102 Rev1.0 (DT)
Workqueue: events ffs_user_copy_worker
task: ffffffc87afc8080 task.stack: ffffffc87a00c000
PC is at __arch_copy_to_user+0x190/0x220
LR is at copy_to_iter+0x78/0x3c8
[...]
[<ffffff800847b790>] __arch_copy_to_user+0x190/0x220
[<ffffff80086f25d8>] ffs_user_copy_worker+0x70/0x130
[<ffffff80080b8c64>] process_one_work+0x1dc/0x460
[<ffffff80080b8f38>] worker_thread+0x50/0x4b0
[<ffffff80080bf5a0>] kthread+0xd8/0xf0
[<ffffff8008083680>] ret_from_fork+0x10/0x50
Address this by placing a set_fs(USER_DS) before of the copy operation
and revert it again once the copy operation has finished.
This patch is analogous to commit d7ffde35e31a ("vhost: use USER_DS in
vhost_worker thread") which addresses the same underlying issue.
Some UDC drivers (like the DWC3) expect that the response to a setup()
request is queued from within the setup function itself so that it is
available as soon as setup() has completed.
Upon receiving a setup request the function fs driver creates an event that
is made available to userspace. And only once userspace has acknowledged
that event the response to the setup request is queued.
So it violates the requirement of those UDC drivers and random failures can
be observed. This is basically a race condition and if userspace is able to
read the event and queue the response fast enough all is good. But if it is
not, for example because other processes are currently scheduled to run,
the USB host that sent the setup request will observe an error.
To avoid this the gadget framework provides the USB_GADGET_DELAYED_STATUS
return code. If a setup() callback returns this value the UDC driver is
aware that response is not yet available and can uses the appropriate
methods to handle this case.
Since in the case of function fs the response will never be available when
the setup() function returns make sure that this status code is used.
This fixed random occasional failures that were previously observed on a
DWC3 based system under high system load.
Added missing GUSBCFG programming in host mode, which fixes
transaction errors issue on HiKey and Altera Cyclone V boards.
These field even if was programmed in device mode (in function
dwc2_hsotg_core_init_disconnected()) will be resetting to POR values
after core soft reset applied.
So, each time when switching to host mode required to set this field
to correct value.
set udev->slot_id to zero when disabling and freeing the xhci slot.
Prevents usb core from calling xhci with a stale slot id.
xHC controller may be reset during resume to recover from some error.
All slots are unusable as they are disabled and freed.
xhci driver starts slot enumeration again from 1 in the order they are
enabled. In the worst case a stale udev->slot_id for one device matches
a newly enabled slot_id for a different device, causing us to
perform a action on the wrong device.
If building a kernel without FTRACE but with TRACING, dwc3.ko fails to
link due to missing trace events. Fix this by using the correct
Kconfig symbol on Makefile.
Reported-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
>From DWC_usb31 programming guide section 1.3.2, once DWC3_DCTL_CSFTRST
bit is cleared, we must wait at least 50ms before accessing the PHY
domain (synchronization delay).
Add native DSD support quirk for Luxman DA-06 DAC, by adding the
PID/VID 1852:5065.
Rename "is_marantz_denon_dac()" function to "is_itf_usb_dsd_2alts_dac()"
to cover broader device family sharing the same USB audio
implementation(*).
For the same reason, rename "is_teac_dsd_dac()" function to
"is_itf_usb_dsd_3alts_dac()".
(*)
These devices have the same USB controller "ITF-USB DSD", supplied by
INTERFACE Co., Ltd.
"ITF-USB DSD" USB controller has two patterns,
Pattern 1. (2 altsets version)
- Altset 0: for control
- Altset 1: for stream (S32)
- Altset 2: for stream (S32, DSD_U32)
Pattern 2. (3 altsets version)
- Altset 0: for control
- Altset 1: for stream (S16)
- Altset 2: for stream (S32)
- Altset 3: for stream (S32, DSD_U32)
"is_itf_usb_dsd_2alts_dac()" returns true, if the DAC has "Pattern 1"
USB controller, and "is_itf_usb_dsd_3alts_dac()" returns true, if
"Pattern2".
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Scatter-gather needs to be disabled when using dma_declare_coherent_memory
and HCD_LOCAL_MEM. Andrea Righi made the equivalent fix for EHCI drivers
in commit 4307a28eb01284 "USB: EHCI: fix NULL pointer dererence in HCDs
that use HCD_LOCAL_MEM".
The following NULL pointer WARN_ON_ONCE triggered with OHCI drivers:
This patch reverts the commit 835e4241e714 ("usb: host: xhci-plat:
enable clk in resume timing") because this driver also has runtime PM
and the commit 560869100b99 ("clk: renesas: cpg-mssr: Restore module
clocks during resume") will restore the clock on R-Car H3 environment.
If the xhci_plat_suspend() disables the clk, the system cannot enable
the clk in resume like the following behavior:
< In resume >
- genpd_resume_noirq() runs and enable the clk (enable_count = 1)
- cpg_mssr_resume_noirq() restores the clk register.
-- Since the clk was disabled in suspend, cpg_mssr_resume_noirq()
will disable the clk and keep the enable_count.
- Even if xhci_plat_resume() calls clk_prepare_enable(), since
the enable_count is 1, the clk will be not enabled.
After this patch is applied, the cpg-mssr driver will save the clk
as enable, so the clk will be enabled in resume.
ACM driver may accept data to transmit while system is not fully
resumed. In this case ACM driver buffers data and prepare URBs
on usb anchor list.
There is a little chance that two tasks put a char and initiate
acm_tty_flush_chars(). In such a case, driver will put one URB
twice on usb anchor list.
This patch also reset length of data before resue of a buffer.
This not only prevent sending rubbish, but also lower risc of race.
Without this patch we hit following kernel panic in one of our
stabilty/stress tests.
We should call dwc2_hsotg_enqueue_setup() after properly
setting lx_state. Because it may cause error-out from
dwc2_hsotg_enqueue_setup() due to wrong value in lx_state.
Issue can be reproduced by loading driver while connected
A-Connector (start in A-HOST mode) then disconnect A-Connector
to switch to B-DEVICE.
Clang reports the following warning:
drivers/usb/gadget/udc/fsl_udc_core.c:1312:10: warning: address of array
'ep->name' will always evaluate to 'true' [-Wpointer-bool-conversion]
if (ep->name)
~~ ~~~~^~~~
It seems that the authors intention was to check if the ep has been
configured through struct_ep_setup. Check whether struct usb_ep name
pointer has been set instead.
Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If there are multiple functions associated with a configuration, then
the UAC2 interfaces may not start at zero. Set the correct first
interface number in the association descriptor so that the audio
interfaces are enumerated correctly in this case.
Reviewed-by: Krzysztof Opasiak <k.opasiak@samsung.com> Signed-off-by: John Keeping <john@metanate.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
syzbot is reporting crashes after memory allocation failure inside
do_kexec_load() [1]. This is because free_transition_pgtable() is called
by both init_transition_pgtable() and machine_kexec_cleanup() when memory
allocation failed inside init_transition_pgtable().
Regarding 32bit code, machine_kexec_free_page_tables() is called by both
machine_kexec_alloc_page_tables() and machine_kexec_cleanup() when memory
allocation failed inside machine_kexec_alloc_page_tables().
Fix this by leaving the error handling to machine_kexec_cleanup()
(and optionally setting NULL after free_page()).
syzbot is reporting ODEBUG messages at hfsplus_fill_super() [1]. This
is because hfsplus_fill_super() forgot to call cancel_delayed_work_sync().
As far as I can see, it is hfsplus_mark_mdb_dirty() from
hfsplus_new_inode() in hfsplus_fill_super() that calls
queue_delayed_work(). Therefore, I assume that hfsplus_new_inode() does
not fail if queue_delayed_work() was called, and the out_put_hidden_dir
label is the appropriate location to call cancel_delayed_work_sync().
There's currently no limit on wiphy names, other than netlink
message size and memory limitations, but that causes issues when,
for example, the wiphy name is used in a uevent, e.g. in rfkill
where we use the same name for the rfkill instance, and then the
buffer there is "only" 2k for the environment variables.
This was reported by syzkaller, which used a 4k name.
Limit the name to something reasonable, I randomly picked 128.
Reported-by: syzbot+230d9e642a85d3fec29c@syzkaller.appspotmail.com Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 2d1d4c1e591f made loop_get_status() drop lo_ctx_mutex before
returning, but the loop_get_status_old(), loop_get_status64(), and
loop_get_status_compat() wrappers don't call loop_get_status() if the
passed argument is NULL. The callers expect that the lock is dropped, so
make sure we drop it in that case, too.
We hit an issue where a loop device on NFS was stuck in
loop_get_status() doing vfs_getattr() after the NFS server died, which
caused a pile-up of uninterruptible processes waiting on lo_ctl_mutex.
There's no reason to hold this lock while we wait on the filesystem;
let's drop it so that other processes can do their thing. We need to
grab a reference on lo_backing_file while we use it, and we can get rid
of the check on lo_device, which has been unnecessary since commit a34c0ae9ebd6 ("[PATCH] loop: remove the bio remapping capability") in
the linux-history tree.
zfcp_erp_adapter_reopen() schedules blocking of all of the adapter's
rports via zfcp_scsi_schedule_rports_block() and enqueues a reopen
adapter ERP action via zfcp_erp_action_enqueue(). Both are separately
processed asynchronously and concurrently.
Blocking of rports is done in a kworker by zfcp_scsi_rport_work(). It
calls zfcp_scsi_rport_block(), which then traces a DBF REC "scpdely" via
zfcp_dbf_rec_trig(). zfcp_dbf_rec_trig() acquires the DBF REC spin lock
and then iterates with list_for_each() over the adapter's ERP ready list
without holding the ERP lock. This opens a race window in which the
current list entry can be moved to another list, causing list_for_each()
to iterate forever on the wrong list, as the erp_ready_head is never
encountered as terminal condition.
Meanwhile the ERP action can be processed in the ERP thread by
zfcp_erp_thread(). It calls zfcp_erp_strategy(), which acquires the ERP
lock and then calls zfcp_erp_action_to_running() to move the ERP action
from the ready to the running list. zfcp_erp_action_to_running() can
move the ERP action using list_move() just during the aforementioned
race window. It then traces a REC RUN "erator1" via zfcp_dbf_rec_run().
zfcp_dbf_rec_run() tries to acquire the DBF REC spin lock. If this is
held by the infinitely looping kworker, it effectively spins forever.
Any adapter recovery can trigger this, such as setting the device offline
or reboot.
V4.9 commit 4eeaa4f3f1d6 ("zfcp: close window with unblocked rport
during rport gone") introduced additional tracing of (un)blocking of
rports. It missed that the adapter->erp_lock must be held when calling
zfcp_dbf_rec_trig().
This fix uses the approach formerly introduced by commit aa0fec62391c
("[SCSI] zfcp: Fix sparse warning by providing new entry in dbf") that got
later removed by commit ae0904f60fab ("[SCSI] zfcp: Redesign of the debug
tracing for recovery actions.").
Introduce zfcp_dbf_rec_trig_lock(), a wrapper for zfcp_dbf_rec_trig() that
acquires and releases the adapter->erp_lock for read.
Reported-by: Sebastian Ott <sebott@linux.ibm.com> Signed-off-by: Jens Remus <jremus@linux.ibm.com> Fixes: 4eeaa4f3f1d6 ("zfcp: close window with unblocked rport during rport gone") Cc: <stable@vger.kernel.org> # 2.6.32+ Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com> Signed-off-by: Steffen Maier <maier@linux.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The BPF JIT need safe guarding against spectre v2 in the sk_load_xxx
assembler stubs and the indirect branches generated by the JIT itself
need to be converted to expolines.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The nospec-branch.c file is compiled without the gcc options to
generate expoline thunks. The return branch of the sysfs show
functions cpu_show_spectre_v1 and cpu_show_spectre_v2 is an indirect
branch as well. These need to be compiled with expolines.
Move the sysfs functions for spectre reporting to a separate file
and loose an '.' for one of the messages.
Cc: stable@vger.kernel.org # 4.16 Fixes: d424986f1d ("s390: add sysfs attributes for spectre") Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The return from the ftrace_stub, _mcount, ftrace_caller and
return_to_handler functions is done with "br %r14" and "br %r1".
These are indirect branches as well and need to use execute
trampolines for CONFIG_EXPOLINE=y.
The ftrace_caller function is a special case as it returns to the
start of a function and may only use %r0 and %r1. For a pre z10
machine the standard execute trampoline uses a LARL + EX to do
this, but this requires *two* registers in the range %r1..%r15.
To get around this the 'br %r1' located in the lowcore is used,
then the EX instruction does not need an address register.
But the lowcore trick may only be used for pre z14 machines,
with noexec=on the mapping for the first page may not contain
instructions. The solution for that is an ALTERNATIVE in the
expoline THUNK generated by 'GEN_BR_THUNK %r1' to switch to
EXRL, this relies on the fact that a machine that supports
noexec=on has EXRL as well.
Cc: stable@vger.kernel.org # 4.16 Fixes: f19fbd5ed6 ("s390: introduce execute-trampolines for branches") Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The return from the memmove, memset, memcpy, __memset16, __memset32 and
__memset64 functions are done with "br %r14". These are indirect branches
as well and need to use execute trampolines for CONFIG_EXPOLINE=y.
Cc: stable@vger.kernel.org # 4.16 Fixes: f19fbd5ed6 ("s390: introduce execute-trampolines for branches") Reviewed-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The return from the crc32_le_vgfm_16/crc32c_le_vgfm_16 and the
crc32_be_vgfm_16 functions are done with "br %r14". These are indirect
branches as well and need to use execute trampolines for CONFIG_EXPOLINE=y.
Cc: stable@vger.kernel.org # 4.16 Fixes: f19fbd5ed6 ("s390: introduce execute-trampolines for branches") Reviewed-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Add a header with macros usable in assembler files to emit alternative
code sequences. It works analog to the alternatives for inline assmeblies
in C files, with the same restrictions and capabilities.
The syntax is
ALTERNATIVE "<default instructions sequence>", \
"<alternative instructions sequence>", \
"<features-bit>"
and
open file, unlink it, then use ioctl(2) to make it immutable or
append only. Now close it and watch the blocks *not* freed...
Immutable/append-only checks belong in ->setattr().
Note: the bug is old and backport to anything prior to 737f2e93b972
("ext2: convert to use the new truncate convention") will need
these checks lifted into ext2_setattr().
Cc: stable@kernel.org Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Recently people reported the NIC stops working after
"ifdown eth0; ifup eth0". It turns out in this case the TX queues are not
enabled, after the refactoring of the common detach logic: when the NIC
has sub-channels, usually we enable all the TX queues after all
sub-channels are set up: see rndis_set_subchannel() ->
netif_device_attach(), but in the case of "ifdown eth0; ifup eth0" where
the number of channels doesn't change, we also must make sure the TX queues
are enabled. The patch fixes the regression.
Fixes: 7b2ee50c0cd5 ("hv_netvsc: common detach logic") Signed-off-by: Dexuan Cui <decui@microsoft.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: K. Y. Srinivasan <kys@microsoft.com> Cc: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Prior to commit 0cf737808ae7 ("hv_netvsc: netvsc_teardown_gpadl() split")
the call sequence in netvsc_device_remove() was as follows (as
implemented in netvsc_destroy_buf()):
1- Send NVSP_MSG1_TYPE_REVOKE_RECV_BUF message
2- Teardown receive buffer GPADL
3- Send NVSP_MSG1_TYPE_REVOKE_SEND_BUF message
4- Teardown send buffer GPADL
5- Close vmbus
This didn't work for WS2016 hosts. Commit 0cf737808ae7
("hv_netvsc: netvsc_teardown_gpadl() split") rearranged the
teardown sequence as follows:
1- Send NVSP_MSG1_TYPE_REVOKE_RECV_BUF message
2- Send NVSP_MSG1_TYPE_REVOKE_SEND_BUF message
3- Close vmbus
4- Teardown receive buffer GPADL
5- Teardown send buffer GPADL
That worked well for WS2016 hosts, but it prevented guests on older hosts from
shutting down after changing network settings. Commit 0ef58b0a05c1
("hv_netvsc: change GPAD teardown order on older versions") ensured the
following message sequence for older hosts
1- Send NVSP_MSG1_TYPE_REVOKE_RECV_BUF message
2- Send NVSP_MSG1_TYPE_REVOKE_SEND_BUF message
3- Teardown receive buffer GPADL
4- Teardown send buffer GPADL
5- Close vmbus
However, with this sequence calling `ip link set eth0 mtu 1000` hangs and the
process becomes uninterruptible. On futher analysis it turns out that on tearing
down the receive buffer GPADL the kernel is waiting indefinitely
in vmbus_teardown_gpadl() for a completion to be signaled.
Here is a snippet of where this occurs:
int vmbus_teardown_gpadl(struct vmbus_channel *channel, u32 gpadl_handle)
{
struct vmbus_channel_gpadl_teardown *msg;
struct vmbus_channel_msginfo *info;
unsigned long flags;
int ret;
info = kmalloc(sizeof(*info) +
sizeof(struct vmbus_channel_gpadl_teardown), GFP_KERNEL);
if (!info)
return -ENOMEM;
The completion is signaled from vmbus_ongpadl_torndown(), which gets called when
the corresponding message is received from the host, which apparently never happens
in that case.
This patch works around the issue by restoring the first mentioned message sequence
for older hosts
Fixes: 0ef58b0a05c1 ("hv_netvsc: change GPAD teardown order on older versions") Signed-off-by: Mohammed Gamal <mgamal@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Split each of the functions into two for each of send/recv buffers.
This will be needed in order to implement a fine-grained messaging
sequence to the host so that we accommodate the requirements of
different Windows versions
Fixes: 0ef58b0a05c12 ("hv_netvsc: change GPAD teardown order on older versions") Signed-off-by: Mohammed Gamal <mgamal@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When changing network interface settings, Windows guests
older than WS2016 can no longer shutdown. This was addressed
by commit 0ef58b0a05c12 ("hv_netvsc: change GPAD teardown order
on older versions"), however the issue also occurs on WS2012
guests that share NVSP protocol versions with WS2016 guests.
Hence we use Windows version directly to differentiate them.
Fixes: 0ef58b0a05c12 ("hv_netvsc: change GPAD teardown order on older versions") Signed-off-by: Mohammed Gamal <mgamal@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Make common function for detaching internals of device
during changes to MTU and RSS. Make sure no more packets
are transmitted and all packets have been received before
doing device teardown.
Change the wait logic to be common and use usleep_range().
Changes transmit enabling logic so that transmit queues are disabled
during the period when lower device is being changed. And enabled
only after sub channels are setup. This avoids issue where it could
be that a packet was being sent while subchannel was not initialized.
Fixes: 8195b1396ec8 ("hv_netvsc: fix deadlock on hotplug") Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
On older versions of Windows, the host ignores messages after
vmbus channel is closed.
Workaround this by doing what Windows does and send the teardown
before close on older versions of NVSP protocol.
Reported-by: Mohammed Gamal <mgamal@redhat.com> Fixes: 0cf737808ae7 ("hv_netvsc: netvsc_teardown_gpadl() split") Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The receive processing may continue to happen while the
internal network device state is in RCU grace period.
The internal RNDIS structure is associated with the
internal netvsc_device structure; both have the same
RCU lifetime.
Defer freeing all associated parts until after grace
period.
Fixes: 0cf737808ae7 ("hv_netvsc: netvsc_teardown_gpadl() split") Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This makes sure that no CPU is still process packets when
the channel is closed.
Fixes: 76bb5db5c749 ("netvsc: fix use after free on module removal") Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When VF is used for accelerated networking it will likely have
more queues (and different policy) than the synthetic NIC.
This patch defers the queue policy to the VF so that all the
queues can be used. This impacts workloads like local generate UDP.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
There is a race between napi_reschedule and re-enabling interrupts
which could lead to missed host interrrupts. This occurs when
interrupts are re-enabled (hv_end_read) and vmbus irq callback
(netvsc_channel_cb) has already scheduled NAPI.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Block setup of multiple channels earlier in the teardown
process. This avoids possible races between halt and subchannel
initialization.
Suggested-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Need to delete NAPI association if vmbus_open fails.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Change the initialization order so that the device is ready to transmit
(ie connect vsp is completed) before setting the internal reference
to the device with RCU.
This avoids any races on initialization and prevents retry issues
on shutdown.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Since we no longer localize channel/CPU affiliation within one NUMA
node, num_online_cpus() is used as the number of channel cap, instead of
the number of processors in a NUMA node.
This patch allows a bigger range for tuning the number of channels.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If the transmit queue is known full, then don't keep aggregating
data. And the cp_partial flag which indicates that the current
aggregation buffer is full can be folded in to avoid more
conditionals.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The gen bits must be read first from (resp. written last to) DMA memory.
The proper way to enforce this on Linux is to call dma_rmb() (resp.
dma_wmb()).
Signed-off-by: Regis Duchesne <hpreg@vmware.com> Acked-by: Ronak Doshi <doshir@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The DMA mask must be set before, not after, the first DMA map operation, or
the first DMA map operation could in theory fail on some systems.
Fixes: b0eb57cb97e78 ("VMXNET3: Add support for virtual IOMMU") Signed-off-by: Regis Duchesne <hpreg@vmware.com> Acked-by: Ronak Doshi <doshir@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We must not call sock_diag_has_destroy_listeners(sk) on a socket
that has no reference on net structure.
BUG: KASAN: use-after-free in sock_diag_has_destroy_listeners include/linux/sock_diag.h:75 [inline]
BUG: KASAN: use-after-free in __sk_free+0x329/0x340 net/core/sock.c:1609
Read of size 8 at addr ffff88018a02e3a0 by task swapper/1/0