Andi Kleen [Wed, 18 Jun 2008 11:58:36 +0000 (13:58 +0200)]
[netdrvr] Fix IOMMU overflow checking in s2io.c
s2io has IOMMU overflow checking, but unfortunately it is wrong.
It didn't use the standard macros, which meant that it only worked
on POWER and SPARC because only those define DMA_ERROR_CODE. Convert it to
use the standard macros instead.
I also commented two more bugs in the IOMMU handling. It assumes
that 0 DMA addresses cannot happen, but that's not true in all IOMMU setups.
The information if a buffer has been already mapped needs to be stored
elsewhere.
Didn't fix those because it needs careful checking of the buffer handling
by the maintainers.
Andy Gospodarek [Thu, 19 Jun 2008 21:19:02 +0000 (17:19 -0400)]
e1000: only enable TSO6 via ethtool when using correct hardware
When enabling TSO via ethool on e1000, it is possible to set
NETIF_F_TSO6 on hardware that does not support it. Setting TSO via
ethtool now matches the settings used when the hardware is probed.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Al Viro [Mon, 23 Jun 2008 01:04:50 +0000 (02:04 +0100)]
[netdrvr] netxen: fix netxen_pci_tbl[] breakage
PCI_DEVICE_CLASS sets .device and .vendor to PCI_ANY_DEV,
which overrides the effect of preceding PCI_DEVICE() and makes
all elements of netxen_pci_tbl[] identical. Introduced in the
commit dcd56fdbaeae1008044687b973c4a3e852e8a726.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Ingo Molnar [Mon, 23 Jun 2008 08:41:23 +0000 (10:41 +0200)]
[netdrvr] 3c59x: remove irqs_disabled warning from local_bh_enable
Original Author: Michael Buesch <mb@bu3sch.de>
net, vortex: fix lockup
Ingo Molnar reported:
-tip testing found that Johannes Berg's "softirq: remove irqs_disabled
warning from local_bh_enable" enhancement to lockdep triggers a new
warning on an old testbox that uses 3c59x vortex and netlogging:
----->
calling vortex_init+0x0/0xb0
PCI: Found IRQ 10 for device 0000:00:0b.0
PCI: Sharing IRQ 10 with 0000:00:0a.0
PCI: Sharing IRQ 10 with 0000:00:0b.1
3c59x: Donald Becker and others.
0000:00:0b.0: 3Com PCI 3c556 Laptop Tornado at e0800400.
PCI: Enabling bus mastering for device 0000:00:0b.0
initcall vortex_init+0x0/0xb0 returned 0 after 47 msecs
...
calling init_netconsole+0x0/0x1b0
netconsole: local port 4444
netconsole: local IP 10.0.1.9
netconsole: interface eth0
netconsole: remote port 4444
netconsole: remote IP 10.0.1.16
netconsole: remote ethernet address 00:19:xx:xx:xx:xx
netconsole: device eth0 not up yet, forcing it
eth0: setting half-duplex.
eth0: setting full-duplex.
------------[ cut here ]------------
WARNING: at kernel/softirq.c:137 local_bh_enable_ip+0xd1/0xe0()
Pid: 1, comm: swapper Not tainted 2.6.26-rc6-tip #2091
[<c0125ecf>] warn_on_slowpath+0x4f/0x70
[<c0126834>] ? release_console_sem+0x1b4/0x1d0
[<c0126d00>] ? vprintk+0x2a0/0x450
[<c012fde5>] ? __mod_timer+0xa5/0xc0
[<c046f7fd>] ? mdio_sync+0x3d/0x50
[<c0160ef6>] ? marker_probe_cb+0x46/0xa0
[<c0126ed7>] ? printk+0x27/0x50
[<c046f4c3>] ? vortex_set_duplex+0x43/0xc0
[<c046f521>] ? vortex_set_duplex+0xa1/0xc0
[<c0471b92>] ? vortex_timer+0xe2/0x3e0
[<c012b361>] local_bh_enable_ip+0xd1/0xe0
[<c08d9f9f>] _spin_unlock_bh+0x2f/0x40
[<c0471b92>] vortex_timer+0xe2/0x3e0
[<c014743b>] ? trace_hardirqs_on+0xb/0x10
[<c0147358>] ? trace_hardirqs_on_caller+0x88/0x160
[<c012f8b2>] run_timer_softirq+0x162/0x1c0
[<c0471ab0>] ? vortex_timer+0x0/0x3e0
[<c012b361>] local_bh_enable_ip+0xd1/0xe0
[<c08d9f9f>] _spin_unlock_bh+0x2f/0x40
[<c0471b92>] vortex_timer+0xe2/0x3e0
[<c014743b>] ? trace_hardirqs_on+0xb/0x10
[<c0147358>] ? trace_hardirqs_on_caller+0x88/0x160
[<c012f8b2>] run_timer_softirq+0x162/0x1c0
[<c0471ab0>] ? vortex_timer+0x0/0x3e0
[<c0471ab0>] ? vortex_timer+0x0/0x3e0
[<c012b60a>] __do_softirq+0x9a/0x160
[<c012b570>] ? __do_softirq+0x0/0x160
[<c0106775>] call_on_stack+0x15/0x30
[<c012b4f5>] ? irq_exit+0x55/0x60
[<c0106e85>] ? do_IRQ+0x85/0xd0
[<c0147391>] ? trace_hardirqs_on_caller+0xc1/0x160
[<c0104888>] ? common_interrupt+0x28/0x30
[<c08d8ac8>] ? mutex_unlock+0x8/0x10
[<c08d8180>] ? _cond_resched+0x10/0x30
[<c07a3be7>] ? netpoll_setup+0x117/0x390
[<c0cbfcfe>] ? init_netconsole+0x14e/0x1b0
[<c013d539>] ? ktime_get+0x19/0x40
[<c0c9bab2>] ? kernel_init+0x1b2/0x2c0
[<c0cbfbb0>] ? init_netconsole+0x0/0x1b0
[<c0396aa4>] ? trace_hardirqs_on_thunk+0xc/0x10
[<c0103f12>] ? restore_nocheck_notrace+0x0/0xe
[<c0c9b900>] ? kernel_init+0x0/0x2c0
[<c0c9b900>] ? kernel_init+0x0/0x2c0
[<c0104aa7>] ? kernel_thread_helper+0x7/0x10
=======================
---[ end trace 37f9c502aff112e0 ]---
console [netcon0] enabled
netconsole: network logging started
initcall init_netconsole+0x0/0x1b0 returned 0 after 2914 msecs
looking at the driver I think the bug is real and the fix actually
is trivial.
vp->lock is also taken in hardware IRQ context, so we _have_ to always
use irqsafe locking. As we run in a timer with IRQs disabled,
we can simply use spin_lock.
Cc: <stable@kernel.org> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Atsushi Nemoto [Thu, 26 Jun 2008 08:14:15 +0000 (17:14 +0900)]
tc35815: Fix receiver hangup on Rx FIFO overflow
On Rx FIFO overflow error, the controller consume a buffer descriptor
but currently the driver does not give it back to the controller.
This results unrecoverable 'Buffer List Exhausted' condition. This
patch fix this problem by moving a "fbl_count--" line to proper place.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Michal Schmidt [Thu, 26 Jun 2008 14:06:19 +0000 (16:06 +0200)]
s2io: fix documentation about intr_type
The documentation for intr_type module parameter of the s2io driver is
not consistent with the code. The comments in drivers/net/s2io.c are
OK, but Documentation/networking/s2io.txt is wrong.
Pointed out by Andrew Hecox.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Ron Rindjunsky [Wed, 25 Jun 2008 08:46:31 +0000 (16:46 +0800)]
iwlwifi: improve scanning band selection management
This patch modifies the band selection management when scanning, so
bands are now scanned according to HW band support.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Fri, 20 Jun 2008 20:11:00 +0000 (22:11 +0200)]
rt2x00: Fix unbalanced mutex locking
The usb_cache_mutex was not correctly released
under all circumstances. Both rt73usb as rt2500usb
didn't release the mutex under certain conditions
when the register access failed. Obviously such
failure would lead to deadlocks.
In addition under similar circumstances when the
bbp register couldn't be read the value must be
set to 0xff to indicate that the value is wrong.
This too didn't happen under all circumstances.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Buesch [Fri, 20 Jun 2008 09:40:46 +0000 (11:40 +0200)]
b43legacy: Fix possible NULL pointer dereference in DMA code
This fixes a possible NULL pointer dereference in an error path of the
DMA allocation error checking code. This is also necessary for a future
DMA API change that is on its way into the mainline kernel that adds
an additional dev parameter to dma_mapping_error().
Signed-off-by: Michael Buesch <mb@bu3sch.de> Cc: stable <stable@kernel.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Buesch [Sun, 15 Jun 2008 14:01:24 +0000 (16:01 +0200)]
b43: Fix possible MMIO access while device is down
This fixes a possible MMIO access while the device is still down
from a suspend cycle. MMIO accesses with the device powered down
may cause crashes on certain devices.
Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Buesch [Sun, 15 Jun 2008 13:17:29 +0000 (15:17 +0200)]
b43: Do not return TX_BUSY from op_tx
Never return TX_BUSY from op_tx. It doesn't make sense to return
TX_BUSY, if we can not transmit the packet.
Drop the packet and return TX_OK.
This will fix the resume hang.
Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tony Vroon [Wed, 11 Jun 2008 20:23:56 +0000 (16:23 -0400)]
mac80211: implement EU regulatory domain
Implement missing EU regulatory domain for mac80211. Based on the
information in IEEE 802.11-2007 (specifically pages 1142, 1143 & 1148)
and ETSI 301 893 (V1.4.1).
With thanks to Johannes Berg.
Signed-off-by: Tony Vroon <tony@linx.net> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Receiving packets while we are cleaning up a network namespace is a
racy proposition. It is possible when the packet arrives that we have
removed some but not all of the state we need to fully process it. We
have the choice of either playing wack-a-mole with the cleanup routines
or simply dropping packets when we don't have a network namespace to
handle them.
Since the check looks inexpensive in netif_receive_skb let's just
drop the incoming packets.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fix warning:
drivers/net/pppoe.c: In function 'pppoe_recvmsg':
drivers/net/pppoe.c:945: warning: comparison of distinct pointer types lacks a cast
because skb->len is unsigned int and total_len is size_t
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6: Drop packets for loopback address from outside of the box.
[ Based upon original report and patch by Karsten Keil. Karsten
has verified that this fixes the TAHI test case "ICMPv6 test
v6LC.5.1.2 Part F". -DaveM ]
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Shan Wei [Thu, 19 Jun 2008 23:29:39 +0000 (16:29 -0700)]
ipv6: Remove options header when setsockopt's optlen is 0
Remove the sticky Hop-by-Hop options header by calling setsockopt()
for IPV6_HOPOPTS with a zero option length, per RFC3542.
Routing header and Destination options header does the same as
Hop-by-Hop options header.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com> Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Wed, 18 Jun 2008 22:39:48 +0000 (15:39 -0700)]
mac80211: detect driver tx bugs
When a driver rejects a frame in it's ->tx() callback, it must also
stop queues, otherwise mac80211 can go into a loop here. Detect this
situation and abort the loop after five retries, warning about the
driver bug.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Wed, 18 Jun 2008 09:07:07 +0000 (02:07 -0700)]
netlink: genl: fix circular locking
genetlink has a circular locking dependency when dumping the registered
families:
- dump start:
genl_rcv() : take genl_mutex
genl_rcv_msg() : call netlink_dump_start() while holding genl_mutex
netlink_dump_start(),
netlink_dump() : take nlk->cb_mutex
ctrl_dumpfamily() : try to detect this case and not take genl_mutex a
second time
- dump continuance:
netlink_rcv() : call netlink_dump
netlink_dump : take nlk->cb_mutex
ctrl_dumpfamily() : take genl_mutex
Register genl_lock as callback mutex with netlink to fix this. This slightly
widens an already existing module unload race, the genl ops used during the
dump might go away when the module is unloaded. Thomas Graf is working on a
seperate fix for this.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
The problem is that the mac80211 stack not only needs to be able to
muck with the link-level headers, it also might need to mangle all of
the packet data if doing sw wireless encryption.
This fixes kernel bugzilla #10903. Thanks to Didier Raboud (for the
bugzilla report), Andrew Prince (for bisecting), Johannes Berg (for
bringing this bisection analysis to my attention), and Ilpo (for
trying to analyze this purely from the TCP side).
In 2.6.27 we can take another stab at this, by using something like
skb_cow_data() when the TX path of mac80211 ends up with a non-NULL
tx->key. The ESP protocol code in the IPSEC stack can be used as a
model for implementation.
Signed-off-by: David S. Miller <davem@davemloft.net>
Rainer Weikusat [Wed, 18 Jun 2008 05:28:05 +0000 (22:28 -0700)]
af_unix: fix 'poll for write'/ connected DGRAM sockets
The unix_dgram_sendmsg routine implements a (somewhat crude)
form of receiver-imposed flow control by comparing the length of the
receive queue of the 'peer socket' with the max_ack_backlog value
stored in the corresponding sock structure, either blocking
the thread which caused the send-routine to be called or returning
EAGAIN. This routine is used by both SOCK_DGRAM and SOCK_SEQPACKET
sockets. The poll-implementation for these socket types is
datagram_poll from core/datagram.c. A socket is deemed to be writeable
by this routine when the memory presently consumed by datagrams
owned by it is less than the configured socket send buffer size. This
is always wrong for connected PF_UNIX non-stream sockets when the
abovementioned receive queue is currently considered to be full.
'poll' will then return, indicating that the socket is writeable, but
a subsequent write result in EAGAIN, effectively causing an
(usual) application to 'poll for writeability by repeated send request
with O_NONBLOCK set' until it has consumed its time quantum.
The change below uses a suitably modified variant of the datagram_poll
routines for both type of PF_UNIX sockets, which tests if the
recv-queue of the peer a socket is connected to is presently
considered to be 'full' as part of the 'is this socket
writeable'-checking code. The socket being polled is additionally
put onto the peer_wait wait queue associated with its peer, because the
unix_dgram_sendmsg routine does a wake up on this queue after a
datagram was received and the 'other wakeup call' is done implicitly
as part of skb destruction, meaning, a process blocked in poll
because of a full peer receive queue could otherwise sleep forever
if no datagram owned by its socket was already sitting on this queue.
Among this change is a small (inline) helper routine named
'unix_recvq_full', which consolidates the actual testing code (in three
different places) into a single location.
Signed-off-by: Rainer Weikusat <rweikusat@mssgmbh.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ang Way Chuang [Wed, 18 Jun 2008 04:10:33 +0000 (21:10 -0700)]
tun: Proper handling of IPv6 header in tun driver when TUN_NO_PI is set
By default, tun.c running in TUN_TUN_DEV mode will set the protocol of
packet to IPv4 if TUN_NO_PI is set. My program failed to work when I
assumed that the driver will check the first nibble of packet,
determine IP version and set the appropriate protocol.
Signed-off-by: Ang Way Chuang <wcang@nav6.org> Acked-by: Max Krasnyansky <maxk@qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Radu Cristescu [Thu, 12 Jun 2008 22:04:54 +0000 (17:04 -0500)]
atl1: relax eeprom mac address error check
The atl1 driver tries to determine the MAC address thusly:
- If an EEPROM exists, read the MAC address from EEPROM and
validate it.
- If an EEPROM doesn't exist, try to read a MAC address from
SPI flash.
- If that fails, try to read a MAC address directly from the
MAC Station Address register.
- If that fails, assign a random MAC address provided by the
kernel.
We now have a report of a system fitted with an EEPROM containing all
zeros where we expect the MAC address to be, and we currently handle
this as an error condition. Turns out, on this system the BIOS writes
a valid MAC address to the NIC's MAC Station Address register, but we
never try to read it because we return an error when we find the all-
zeros address in EEPROM.
This patch relaxes the error check and continues looking for a MAC
address even if it finds an illegal one in EEPROM.
Signed-off-by: Radu Cristescu <advantis@gmx.net> Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
David Brownell [Fri, 13 Jun 2008 04:38:06 +0000 (21:38 -0700)]
net/enc28j60: low power mode
Keep enc28j60 chips in low-power mode when they're not in use.
At typically 120 mA, these chips run hot even when idle; this
low power mode cuts that power usage by a factor of around 100.
This version provides a generic routine to poll a register until
its masked value equals some value ... e.g. bit set or cleared.
It's basically what the previous wait_phy_ready() did, but this
version is generalized to support the handshaking needed to
enter and exit low power mode.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Claudio Lanconelli <lanconelli.claudio@eptar.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Josh Boyer [Tue, 17 Jun 2008 23:27:55 +0000 (19:27 -0400)]
ibm_newemac: select CRC32 in Kconfig
The ibm_newemac driver requires ether_crc to be defined. Apparently it is
possible to generate a .config without CONFIG_CRC32 set which causes the
following link errors if IBM_NEW_EMAC is selected:
LD .tmp_vmlinux1
drivers/built-in.o: In function `emac_hash_mc':
core.c:(.text+0x2f524): undefined reference to `crc32_le'
core.c:(.text+0x2f528): undefined reference to `bitrev32'
make: *** [.tmp_vmlinux1] Error 1
This patch has IBM_NEW_EMAC select CRC32 so we don't hit this error.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Steffen Klassert [Tue, 17 Jun 2008 23:37:13 +0000 (16:37 -0700)]
xfrm: fix fragmentation for ipv4 xfrm tunnel
When generating the ip header for the transformed packet we just copy
the frag_off field of the ip header from the original packet to the ip
header of the new generated packet. If we receive a packet as a chain
of fragments, all but the last of the new generated packets have the
IP_MF flag set. We have to mask the frag_off field to only keep the
IP_DF flag from the original packet. This got lost with git commit 36cf9acf93e8561d9faec24849e57688a81eb9c5 ("[IPSEC]: Separate
inner/outer mode processing on output")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
The H.245 helper is not registered/unregistered, but assigned to
connections manually from the Q.931 helper. This means on unload
existing expectations and connections using the helper are not
cleaned up, leading to the following oops on module unload:
One way to fix this would be to split helper cleanup from the unregistration
function and invoke it for the H.245 helper, but since ctnetlink needs to be
able to find the helper for synchonization purposes, a better fix is to
register it normally and make sure its not assigned to connections during
helper lookup. The missing l3num initialization is enough for this, this
patch changes it to use AF_UNSPEC to make it more explicit though.
Reported-by: liannan <liannan@twsz.com> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Tue, 17 Jun 2008 22:51:47 +0000 (15:51 -0700)]
netfilter: nf_nat: fix RCU races
Fix three ct_extend/NAT extension related races:
- When cleaning up the extension area and removing it from the bysource hash,
the nat->ct pointer must not be set to NULL since it may still be used in
a RCU read side
- When replacing a NAT extension area in the bysource hash, the nat->ct
pointer must be assigned before performing the replacement
- When reallocating extension storage in ct_extend, the old memory must
not be freed immediately since it may still be used by a RCU read side
atm: [iphase] doesn't call phy->start due to a bogus #ifndef
This causes the suni driver to oops if you try to use sonetdiag to get
the statistics. Also add the corresponding phy->stop call to fix another
oops if you try to remove the module.
Signed-off-by: Jorge Boncompte [DTI2] <jorge@dti2.net> Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil> Signed-off-by: David S. Miller <davem@davemloft.net>
atm: [iphase] set drvdata before enabling interrupts
Signed-off-by: Jorge Boncompte [DTI2] <jorge@dti2.net> Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil> Signed-off-by: David S. Miller <davem@davemloft.net>
It happens that if a packet arrives in a VC between the call to open it on
the hardware and the call to change the backend to br2684, br2684_regvcc
processes the packet and oopses dereferencing skb->dev because it is
NULL before the call to br2684_push().
Signed-off-by: Jorge Boncompte [DTI2] <jorge@dti2.net> Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil>
Ben Hutchings [Tue, 17 Jun 2008 00:02:28 +0000 (17:02 -0700)]
net: Fix test for VLAN TX checksum offload capability
Selected device feature bits can be propagated to VLAN devices, so we
can make use of TX checksum offload and TSO on VLAN-tagged packets.
However, if the physical device does not do VLAN tag insertion or
generic checksum offload then the test for TX checksum offload in
dev_queue_xmit() will see a protocol of htons(ETH_P_8021Q) and yield
false.
This splits the checksum offload test into two functions:
- can_checksum_protocol() tests a given protocol against a feature bitmask
- dev_can_checksum() first tests the skb protocol against the device
features; if that fails and the protocol is htons(ETH_P_8021Q) then
it tests the encapsulated protocol against the effective device
features for VLANs
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Acked-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Yasevich [Tue, 17 Jun 2008 00:00:29 +0000 (17:00 -0700)]
sctp: Correclty set changeover_active for SFR-CACC
Right now, any time we set a primary transport we set
the changeover_active flag. As a result, we invoke SFR-CACC
even when there has been no changeover events.
Only set changeover_active, when there is a true changeover
event, i.e. we had a primary path and we are changing to
another transport.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Mon, 16 Jun 2008 23:59:55 +0000 (16:59 -0700)]
sctp: Correctly cleanup procfs entries upon failure.
This patch remove the proc fs entry which has been created if fail to
set up proc fs entry for the SCTP protocol.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6 sit: Avoid extra need for compat layer in PRL management.
We've introduced extra need of compat layer for ip_tunnel_prl{}
for PRL (Potential Router List) management. Though compat_ioctl
is still missing in ipv4/ipv6, let's make the interface more
straight-forward and eliminate extra need for nasty compat layer
anyway since the interface is new for 2.6.26.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
pkt_sched: HTB scheduler, change default hysteresis mode to off.
The HTB hysteresis mode reduce the CPU load, but at the
cost of scheduling accuracy.
On ADSL links (512 kbit/s upstream), this inaccuracy introduce
significant jitter, enought to disturbe VoIP. For details see my
masters thesis (http://www.adsl-optimizer.dk/thesis/), chapter 7,
section 7.3.1, pp 69-70.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk> Acked-by: Martin Devera <devik@cdi.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
Abhijeet Kolekar [Thu, 12 Jun 2008 01:47:16 +0000 (09:47 +0800)]
mac80211 : fix for iwconfig in ad-hoc mode
The patch checks interface status, if it is in IBSS_JOINED mode
show cell id it is associated with.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Randy Dunlap [Wed, 11 Jun 2008 20:32:22 +0000 (13:32 -0700)]
rt2x00: LEDS build failure
Config symbols that select LEDS_CLASS need to depend on NEW_LEDS so that
undefined symbols are not used in the build.
The alternative is to select NEW_LEDS, which some drivers do.
This patch fixes the led_* symbols build errors.
(.text+0x174cdc): undefined reference to `input_unregister_device'
(.text+0x174d9f): undefined reference to `input_allocate_device'
(.text+0x174e2d): undefined reference to `input_register_device'
(.text+0x174e53): undefined reference to `input_free_device'
rt2x00rfkill.c:(.text+0x176dc4): undefined reference to `input_allocate_polled_device'
rt2x00rfkill.c:(.text+0x176e8b): undefined reference to `input_event'
rt2x00rfkill.c:(.text+0x176e9f): undefined reference to `input_event'
(.text+0x176eca): undefined reference to `input_unregister_polled_device'
(.text+0x176efc): undefined reference to `input_free_polled_device'
(.text+0x176f37): undefined reference to `input_free_polled_device'
(.text+0x176fd8): undefined reference to `input_register_polled_device'
(.text+0x1772c0): undefined reference to `led_classdev_resume'
(.text+0x1772d4): undefined reference to `led_classdev_resume'
(.text+0x1772e8): undefined reference to `led_classdev_resume'
(.text+0x17730a): undefined reference to `led_classdev_suspend'
(.text+0x17731e): undefined reference to `led_classdev_suspend'
(.text+0x17732f): undefined reference to `led_classdev_suspend'
rt2x00leds.c:(.text+0x177348): undefined reference to `led_classdev_unregister'
rt2x00leds.c:(.text+0x1773c0): undefined reference to `led_classdev_register'
rfkill-input.c:(.text+0x209e4c): undefined reference to `input_close_device'
rfkill-input.c:(.text+0x209e53): undefined reference to `input_unregister_handle'
rfkill-input.c:(.text+0x209ea1): undefined reference to `input_register_handle'
rfkill-input.c:(.text+0x209eae): undefined reference to `input_open_device'
rfkill-input.c:(.text+0x209ebb): undefined reference to `input_unregister_handle'
rfkill-input.c:(.init.text+0x17405): undefined reference to `input_register_handler'
rfkill-input.c:(.exit.text+0x194f): undefined reference to `input_unregister_handler'
make[1]: *** [vmlinux] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Randy Dunlap [Wed, 11 Jun 2008 19:57:58 +0000 (12:57 -0700)]
rt2x00: INPUT build failure
Config symbols that select RFKILL need to depend on INPUT so that
undefined symbols are not used in the build.
This patch fixes the input_* symbols build errors.
(.text+0x174cdc): undefined reference to `input_unregister_device'
(.text+0x174d9f): undefined reference to `input_allocate_device'
(.text+0x174e2d): undefined reference to `input_register_device'
(.text+0x174e53): undefined reference to `input_free_device'
rt2x00rfkill.c:(.text+0x176dc4): undefined reference to `input_allocate_polled_device'
rt2x00rfkill.c:(.text+0x176e8b): undefined reference to `input_event'
rt2x00rfkill.c:(.text+0x176e9f): undefined reference to `input_event'
(.text+0x176eca): undefined reference to `input_unregister_polled_device'
(.text+0x176efc): undefined reference to `input_free_polled_device'
(.text+0x176f37): undefined reference to `input_free_polled_device'
(.text+0x176fd8): undefined reference to `input_register_polled_device'
(.text+0x1772c0): undefined reference to `led_classdev_resume'
(.text+0x1772d4): undefined reference to `led_classdev_resume'
(.text+0x1772e8): undefined reference to `led_classdev_resume'
(.text+0x17730a): undefined reference to `led_classdev_suspend'
(.text+0x17731e): undefined reference to `led_classdev_suspend'
(.text+0x17732f): undefined reference to `led_classdev_suspend'
rt2x00leds.c:(.text+0x177348): undefined reference to `led_classdev_unregister'
rt2x00leds.c:(.text+0x1773c0): undefined reference to `led_classdev_register'
rfkill-input.c:(.text+0x209e4c): undefined reference to `input_close_device'
rfkill-input.c:(.text+0x209e53): undefined reference to `input_unregister_handle'
rfkill-input.c:(.text+0x209ea1): undefined reference to `input_register_handle'
rfkill-input.c:(.text+0x209eae): undefined reference to `input_open_device'
rfkill-input.c:(.text+0x209ebb): undefined reference to `input_unregister_handle'
rfkill-input.c:(.init.text+0x17405): undefined reference to `input_register_handler'
rfkill-input.c:(.exit.text+0x194f): undefined reference to `input_unregister_handler'
make[1]: *** [vmlinux] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Buesch [Thu, 12 Jun 2008 09:58:56 +0000 (11:58 +0200)]
b43: Fix possible NULL pointer dereference in DMA code
This fixes a possible NULL pointer dereference in an error path of the
DMA allocation error checking code. This is also necessary for a future
DMA API change that is on its way into the mainline kernel that adds
an additional dev parameter to dma_mapping_error().
This patch moves the whole struct b43_dmaring struct initialization
right before any DMA allocation operation.
Reported-by: Miles Lane <miles.lane@gmail.com> Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
None of the rt2x00 PCI devices support 64-bit DMA addresses (they all
only accept 32-bit buffer addresses). Hence it makes no sense to try to
enable 64-bit DMA addresses. Only try to enable 32-bit DMA addresses.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Tue, 3 Jun 2008 18:29:50 +0000 (20:29 +0200)]
rt2x00: Don't kill guardian_urb when it wasn't created
This fixes a "BUG: unable to handle kernel paging request"
bug in rt73usb which was caused by killing the guardian_urb
while it had never been allocated for rt73usb.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
parisc: update my email address
parisc: fix miscompilation of ip_fast_csum with gcc >= 4.3
parisc: fix off by one in setup_sigcontext32
parisc: export empty_zero_page
parisc: export copy_user_page_asm
parisc: move head.S to head.text section
Revert "parisc: fix trivial section name warnings"
Linus Torvalds [Fri, 13 Jun 2008 14:40:57 +0000 (07:40 -0700)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ahci: Workaround HW bug for SB600/700 SATA controller PMP support
ahci: workarounds for mcp65
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
tcp: Revert 'process defer accept as established' changes.
ipv6: Fix duplicate initialization of rawv6_prot.destroy
bnx2x: Updating the Maintainer
net: Eliminate flush_scheduled_work() calls while RTNL is held.
drivers/net/r6040.c: correct bad use of round_jiffies()
fec_mpc52xx: MPC52xx_MESSAGES_DEFAULT: 2nd NETIF_MSG_IFDOWN => IFUP
ipg: fix receivemode IPG_RM_RECEIVEMULTICAST{,HASH} in ipg_nic_set_multicast_list()
netfilter: nf_conntrack: fix ctnetlink related crash in nf_nat_setup_info()
netfilter: Make nflog quiet when no one listen in userspace.
ipv6: Fail with appropriate error code when setting not-applicable sockopt.
ipv6: Check IPV6_MULTICAST_LOOP option value.
ipv6: Check the hop limit setting in ancillary data.
ipv6 route: Fix route lifetime in netlink message.
ipv6 mcast: Check address family of gf_group in getsockopt(MS_FILTER).
dccp: Bug in initial acknowledgment number assignment
dccp ccid-3: X truncated due to type conversion
dccp ccid-3: TFRC reverse-lookup Bug-Fix
dccp ccid-2: Bug-Fix - Ack Vectors need to be ignored on request sockets
dccp: Fix sparse warnings
dccp ccid-3: Bug-Fix - Zero RTT is possible
Tejun Heo [Mon, 9 Jun 2008 15:13:04 +0000 (00:13 +0900)]
ahci: workarounds for mcp65
MCP65 ahci can do NCQ but doesn't set the CAP bit and rev A0 and A1
can't do MSI but have MSI capability. Implement AHCI_HFLAG_YES_NCQ
and apply appropriate workarounds.
Sergey Lapin [Thu, 12 Jun 2008 22:21:55 +0000 (15:21 -0700)]
rtc: Ramtron FM3130 RTC support
Ramtron FM3130 is a chip with two separate devices inside, RTC clock and
FRAM. This driver provides only RTC functionality.
This chip is met in lots of custom boards with AT91SAMXXXX CPU I work
with, is cheap and in no way better or worse than any other RTC on market.
While it is mostly met on much smaller devices, I think it is great to
have it supported in Linux.
Signed-off-by: Sergey Lapin <slapin@ossfans.org> Signed-off-by: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Brownell [Thu, 12 Jun 2008 22:21:55 +0000 (15:21 -0700)]
rtc: make HPET_RTC_IRQ track HPET_EMULATE_RTC
More Kconfig tweaks related to the legacy PC RTC code:
- Describe the legacy PC RTC driver as such ... it's never quite
been clear that this driver is for PC RTCs, and now it's fair
to call this the "legacy" driver.
- Force it to understand about HPET stealing its IRQs ... kernel
code does this always when HPET is in use, there should be no
option for users to goof up the config.
This seems to fix kernel bugzilla #10729.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Maxim Levitsky <maximlevitsky@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stas Sergeev [Thu, 12 Jun 2008 22:21:54 +0000 (15:21 -0700)]
provide rtc_cmos platform device
Recently (around 2.6.25) I've noticed that RTC no longer works for me. It
turned out this is because I use pnpacpi=off kernel option to work around
the parport_pc bugs. I always did so, but RTC used to work fine in the
past, and now it have regressed.
The patch fixes the problem by creating the platform device for the RTC
when PNP is disabled. This may also help running the PNP-enabled kernel
on an older PCs.
Signed-off-by: Stas Sergeev <stsp@aknet.ru> Cc: David Brownell <david-b@pacbell.net> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Bjorn Helgaas <bjorn.helgaas@hp.com> Cc: Adam Belay <ambx1@neo.rr.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nick Piggin [Thu, 12 Jun 2008 22:21:52 +0000 (15:21 -0700)]
radix-tree: fix small lockless radix-tree bug
We shrink a radix tree when its root node has only one child, in the left
most slot. The child becomes the new root node. To perform this
operation in a manner compatible with concurrent lockless lookups, we
atomically switch the root pointer from the parent to its child.
However a concurrent lockless lookup may now have loaded a pointer to the
parent (and is presently deciding what to do next). For this reason, we
also have to keep the parent node in a valid state after shrinking the
tree, until the next RCU grace period -- otherwise this lookup with the
parent pointer may not do the right thing. Notably, we need to keep the
child in the left most slot there in case that is requested by the lookup.
This is all pretty standard RCU stuff. It is worth repeating because in
my eagerness to obey the radix tree node constructor scheme, I had broken
it by zeroing the radix tree node before the grace period.
What could happen is that a lookup can load the parent pointer, then
decide it wants to follow the left most child slot, only to find the slot
contained NULL due to the concurrent shrinker having zeroed the parent
node before waiting for a grace period. The lookup would return a false
negative as a result.
Fix it by doing that clearing in the RCU callback. I would normally want
to rip out the constructor entirely, but radix tree nodes are one of those
places where they make sense (only few cachelines will be touched soon
after allocation).
This was never actually found in any lockless pagecache testing or by the
test harness, but by seeing the odd problem with my scalable vmap rewrite.
I have not tickled the test harness into reproducing it yet, but I'll
keep working at it.
Fortunately, it is not a problem anywhere lockless pagecache is used in
mainline kernels (pagecache probe is not a guarantee, and brd does not
have concurrent lookups and deletes).
Signed-off-by: Nick Piggin <npiggin@suse.de> Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: "Paul E. McKenney" <paulmck@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
because that changeset made k_self consider the value as a latin1
character when in Unicode mode, which is wrong; k_self should still take
the console map into account.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Menage [Thu, 12 Jun 2008 22:21:49 +0000 (15:21 -0700)]
/proc/sysvipc/shm: fix 32-bit truncation of segment sizes
sysvipc_shm_proc_show() picks between format strings (based on the
expected maximum length of a SHM segment) in a way that prevents gcc from
performing format checks on the seq_printf() parameters. This hid two
format errors - shp->shm_segsz and shp->shm_nattach are both unsigned
long, but were being printed as unsigned int and signed int respectively.
This leads to 32-bit truncation of SHM segment sizes reported in
/proc/sysvipc/shm. (And for nattach, but that's less of a problem for
most users).
This patch makes the format string directly visible to gcc's format
specifier checker, and fixes the two broken format specifiers.
Signed-off-by: Paul Menage <menage@google.com> Cc: Nadia Derbey <Nadia.Derbey@bull.net> Cc: Manfred Spraul <manfred@colorfullife.com> Cc: Pierre Peiffer <peifferp@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Hansen [Thu, 12 Jun 2008 22:21:47 +0000 (15:21 -0700)]
pagemap: pass mm into pagewalkers
We need this at least for huge page detection for now, because powerpc
needs the vm_area_struct to be able to determine whether a virtual address
is referring to a huge page (its pmd_huge() doesn't work).
It might also come in handy for some of the other users.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com> Acked-by: Matt Mackall <mpm@selenic.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The generic nvram driver announces itself as
'Macintosh non-volatile memory driver'
instead of 'Generic non-volatile memory driver'. Fix that.
Signed-off-by: Philippe De Muyter <phdm@macqel.be> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Paul Mackerras <paulus@samba.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / mirror_ubuntu-artful-kernel.git / log